| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The DSU PMU allows monitoring performance events in the DSU cluster,
which is done by configuring and reading back values from the DSU PMU
system registers. However, for write-access to be allowed by ELs lower
than EL3, the EL3 firmware needs to update the setting on the ACTLR3_EL3
register, as it is disallowed by default.
That configuration is not done on the firmware used by the MT8195 SoC,
as a consequence, booting a MT8195-based machine like
mt8195-cherry-tomato-r2 with CONFIG_ARM_DSU_PMU enabled hangs the kernel
just as it writes to the CLUSTERPMOVSCLR_EL1 register, since the
instruction faults to EL3, and BL31 apparently just re-runs the
instruction over and over.
Mark the DSU PMU node in the Devicetree with status "fail", as the
machine doesn't have a suitable firmware to make use of it from the
kernel, and allowing its driver to probe would hang the kernel.
Fixes: 37f2582883be ("arm64: dts: Add mediatek SoC mt8195 and evaluation board")
Signed-off-by: Nícolas F. R. A. Prado <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Signed-off-by: AngeloGioacchino Del Regno <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
dtbs_check throws a warning at t-phy nodes:
Warning (unit_address_vs_reg): /t-phy@1a243000: node has a unit name, but no reg or ranges property
Warning (unit_address_vs_reg): /soc/t-phy@11c00000: node has a unit name, but no reg or ranges property
The ranges is empty thus removing the `@1a243000`, `@11c00000` from
the node name.
Fixes: 6029cae696c8 ("arm64: dts: mediatek: mt7622: harmonize node names and compatibles")
Fixes: 918aed7abd2d ("arm64: dts: mt7986: add pcie related device nodes")
Signed-off-by: Eugen Hristev <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Signed-off-by: AngeloGioacchino Del Regno <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
The dts file of the MediaTek MT8195 demo board has been updated to include
new reserved memory regions.
These reserved memory regions are:
- SCP
- VPU,
- Sound DMA
- APU.
These regions are defined with the "shared-dma-pool" compatible property.
In addition, the existing reserved memory regions have been reordered by
their addresses to improve readability and maintainability of the DTS
file.
Cc: [email protected] # 6.1, 6.4, 6.5
Fixes: e4a417520101 ("arm64: dts: mediatek: mt8195-demo: fix the memory size of node secmon")
Signed-off-by: Macpaul Lin <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Signed-off-by: AngeloGioacchino Del Regno <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
The onboard dram of mt8195-demo board is 8GB.
Cc: [email protected] # 6.1, 6.4, 6.5
Fixes: 6147314aeedc ("arm64: dts: mediatek: Add device-tree for MT8195 Demo board")
Signed-off-by: Macpaul Lin <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Signed-off-by: AngeloGioacchino Del Regno <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
I am a top reviewer mainly for MediaTek SoC related patches in most
subsystems and I've also been upstreaming both improvements, fixes
and new drivers and devicetrees when required.
The MediaTek scene saw a generous increase in number of patches that
are sent to the lists every week, increasing the amount of required
efforts to maintain the MTK bits overall, and we will possibly see
even more of that.
For this reason, and also because of suggestions and encouragement
coming from the community, I'm stepping up to be a co-maintainer of
MediaTek SoCs support.
Acked-by: Matthias Brugger <[email protected]>
Signed-off-by: AngeloGioacchino Del Regno <[email protected]>
Acked-by: Mathieu Poirier <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
https://git.linaro.org/people/jens.wiklander/linux-tee into arm/fixes
AMDTEE fix possible use-after-free
* tag 'amdtee-fix-for-v6.6' of https://git.linaro.org/people/jens.wiklander/linux-tee:
tee: amdtee: fix use-after-free vulnerability in amdtee_close_session
Link: https://lore.kernel.org/r/20231003171835.GA669924@rayden
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
The correct name of this chip is MXC4005, not MX4005. This is confirmed
both by the manufacturer website and by the title of the original commit,
which added other MXCxxxx devices as well but only this one misses a "c" in
the compatible string.
Signed-off-by: Luca Ceresoli <[email protected]>
Fixes: d9bf5d37fd58 ("dt-bindings:trivial-devices: Add memsic,mxc4005/mxc6255/mxc6655 entries")
Reviewed-by: Krzysztof Kozlowski <[email protected]>
Link: https://lore.kernel.org/r/20231004-mxc4005-device-tree-support-v1-1-e7c0faea72e4@bootlin.com
Signed-off-by: Rob Herring <[email protected]>
|
|
The 'msi' child node schema is missing constraints on additional properties.
It turns out it is incomplete and properties for it are documented in the
parent node by mistake. Move the reference to msi-controller.yaml and
the custom properties to the 'msi' node. Adding 'unevaluatedProperties'
ensures all the properties in the 'msi' node are documented.
With the schema corrected, a minimal interrupt controller node is needed
to properly decode the interrupt properties since the example has
multiple interrupt parents.
Acked-by: Conor Dooley <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Fixes: 905b986d099c ("dt-bindings: pci: Convert iProc PCIe to YAML")
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Rob Herring <[email protected]>
|
|
Drop the unnecessary listing of properties already defined in
pci-bus.yaml. Unless there are additional constraints, it is not
necessary.
Acked-by: Conor Dooley <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Rob Herring <[email protected]>
|
|
The example's indentation is off. While fixing this, the 'bus' node
is unnecessary and can be dropped. It is also preferred to split up
unrelated examples to their own entries.
Reviewed-by: Florian Fainelli <[email protected]>
Acked-by: Conor Dooley <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Rob Herring <[email protected]>
|
|
Just as unevaluatedProperties or additionalProperties are required at
the top level of schemas, they should (and will) also be required for
child node schemas. That ensures only documented properties are
present for any node.
Acked-by: Conor Dooley <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Rob Herring <[email protected]>
|
|
A bus schema based on simple-pm-bus shouldn't define how many 'reg' entries
a child device has. That is a property of the device. Drop the 'reg' entry.
Reviewed-by: Liu Ying <[email protected]>
Acked-by: Conor Dooley <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Rob Herring <[email protected]>
|
|
On i.MX8MQ the MIPI CSI block does have an associated power-domain, but
the CSI bridge does not.
Remove the power-domains requirement from the i.MX8MQ CSI bridge
to fix the following schema warning:
imx8mq-librem5-r4.dtb: csi@30a90000: 'power-domains' is a required property
from schema $id: http://devicetree.org/schemas/media/nxp,imx7-csi.yaml#
Fixes: de655386845a ("media: dt-bindings: media: imx7-csi: Document i.MX8M power-domains property")
Signed-off-by: Fabio Estevam <[email protected]>
Acked-by: Conor Dooley <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Rob Herring <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull PCI fixes from Bjorn Helgaas:
- Fix a qcom register offset that broke IPQ8074 PCIe controller
enumeration (Sricharan Ramabadhran)
- Handle interrupt parsing failures when creating a device tree node to
avoid using uninitialized data (Lizhi Hou)
- Clean up if adding PCI device node fails when creating a device tree
node to avoid a memory leak (Lizhi Hou)
- If a link is down, mark all downstream devices as "disconnected" so
we don't wait for them on resume (Mika Westerberg)
* tag 'pci-v6.6-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
PCI/PM: Mark devices disconnected if upstream PCIe link is down on resume
PCI: of: Destroy changeset when adding PCI device node fails
PCI: of_property: Handle interrupt parsing failures
PCI: qcom: Fix IPQ8074 enumeration
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver fixes from Hans de Goede:
"Bug fixes, build warning fixes and DMI quirk additions"
* tag 'platform-drivers-x86-v6.6-4' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86: hp-wmi:: Mark driver struct with __refdata to prevent section mismatch warning
platform/x86: touchscreen_dmi: Add info for the Positivo C4128B
platform/x86: touchscreen_dmi: Add info for the BUSH Bush Windows tablet
platform/mellanox: tmfifo: fix kernel-doc warnings
platform/x86/intel/ifs: release cpus_read_lock()
platform/x86: hp-bioscfg: Fix reference leak
platform/x86: think-lmi: Fix reference leak
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
- reject unknown mount options
- adjust transaction abort error message level
- fix one more build warning with -Wmaybe-uninitialized
- proper error handling in several COW-related cases
* tag 'for-6.6-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: error out when reallocating block for defrag using a stale transaction
btrfs: error when COWing block from a root that is being deleted
btrfs: error out when COWing block using a stale transaction
btrfs: always print transaction aborted messages with an error level
btrfs: reject unknown mount options early
btrfs: fix some -Wmaybe-uninitialized warnings in ioctl.c
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"A typo fix for a PMU driver, a workround for a side-channel erratum on
Cortex-A520 and a fix for the local timer save/restore when using ACPI
with Qualcomm's custom CPUs:
- Workaround for Cortex-A520 erratum #2966298
- Fix typo in Arm CMN PMU driver that breaks counter overflow handling
- Fix timer handling across idle for Qualcomm custom CPUs"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
cpuidle, ACPI: Evaluate LPI arch_flags for broadcast timer
arm64: errata: Add Cortex-A520 speculative unprivileged load workaround
arm64: Add Cortex-A520 CPU part definition
perf/arm-cmn: Fix the unhandled overflow status of counter 4 to 7
|
|
Pull drm fixes from Dave Airlie:
"Regular weekly pull, all seems pretty normal, i915 and amdgpu mostly.
There is one small new uAPI addition for nouveau but getting it in now
avoids a bunch of userspace dances, and it's for a userspace that
hasn't yet released, so should have no side effects.
i915:
- Fix for OpenGL CTS regression on Compute Shaders
- Fix for default engines initialization
- Fix TLB invalidation for Multi-GT devices
amdgpu:
- Add missing unique_id for GC 11.0.3
- Fix memory leak in FRU error path
- Fix PCIe link reporting on some SMU 11 parts
- Fix ACPI _PR3 detection
- Fix DISPCLK WDIVIDER handling in OTG code
tests:
- Fix kunit release
panel:
- panel-orientation: Add quirk for One Mix 25
nouveau:
- Report IB limit via getparams
- Replace some magic numbers with constants
- small clean up"
* tag 'drm-fixes-2023-10-06' of git://anongit.freedesktop.org/drm/drm:
drm/amd/display: apply edge-case DISPCLK WDIVIDER changes to master OTG pipes only
drm/amd: Fix detection of _PR3 on the PCIe root port
drm/amd: Fix logic error in sienna_cichlid_update_pcie_parameters()
drm/amdgpu: Fix a memory leak
drm/amd/pm: add unique_id for gc 11.0.3
drm/i915: Invalidate the TLBs on each GT
drm/i915: Register engines early to avoid type confusion
drm/i915: Don't set PIPE_CONTROL_FLUSH_L3 for aux inval
drm/nouveau: exec: report max pushs through getparam
drm/nouveau: chan: use channel class definitions
drm/nouveau: chan: use struct nvif_mclass
drm: panel-orientation-quirks: Add quirk for One Mix 2S
drm/tests: Fix kunit_release_action ctx argument
|
|
hidpp_connect_event() has *four* time-of-check vs time-of-use (TOCTOU)
races when it races with itself.
hidpp_connect_event() primarily runs from a workqueue but it also runs
on probe() and if a "device-connected" packet is received by the hw
when the thread running hidpp_connect_event() from probe() is waiting on
the hw, then a second thread running hidpp_connect_event() will be
started from the workqueue.
This opens the following races (note the below code is simplified):
1. Retrieving + printing the protocol (harmless race):
if (!hidpp->protocol_major) {
hidpp_root_get_protocol_version()
hidpp->protocol_major = response.rap.params[0];
}
We can actually see this race hit in the dmesg in the abrt output
attached to rhbz#2227968:
[ 3064.624215] logitech-hidpp-device 0003:046D:4071.0049: HID++ 4.5 device connected.
[ 3064.658184] logitech-hidpp-device 0003:046D:4071.0049: HID++ 4.5 device connected.
Testing with extra logging added has shown that after this the 2 threads
take turn grabbing the hw access mutex (send_mutex) so they ping-pong
through all the other TOCTOU cases managing to hit all of them:
2. Updating the name to the HIDPP name (harmless race):
if (hidpp->name == hdev->name) {
...
hidpp->name = new_name;
}
3. Initializing the power_supply class for the battery (problematic!):
hidpp_initialize_battery()
{
if (hidpp->battery.ps)
return 0;
probe_battery(); /* Blocks, threads take turns executing this */
hidpp->battery.desc.properties =
devm_kmemdup(dev, hidpp_battery_props, cnt, GFP_KERNEL);
hidpp->battery.ps =
devm_power_supply_register(&hidpp->hid_dev->dev,
&hidpp->battery.desc, cfg);
}
4. Creating delayed input_device (potentially problematic):
if (hidpp->delayed_input)
return;
hidpp->delayed_input = hidpp_allocate_input(hdev);
The really big problem here is 3. Hitting the race leads to the following
sequence:
hidpp->battery.desc.properties =
devm_kmemdup(dev, hidpp_battery_props, cnt, GFP_KERNEL);
hidpp->battery.ps =
devm_power_supply_register(&hidpp->hid_dev->dev,
&hidpp->battery.desc, cfg);
...
hidpp->battery.desc.properties =
devm_kmemdup(dev, hidpp_battery_props, cnt, GFP_KERNEL);
hidpp->battery.ps =
devm_power_supply_register(&hidpp->hid_dev->dev,
&hidpp->battery.desc, cfg);
So now we have registered 2 power supplies for the same battery,
which looks a bit weird from userspace's pov but this is not even
the really big problem.
Notice how:
1. This is all devm-maganaged
2. The hidpp->battery.desc struct is shared between the 2 power supplies
3. hidpp->battery.desc.properties points to the result from the second
devm_kmemdup()
This causes a use after free scenario on USB disconnect of the receiver:
1. The last registered power supply class device gets unregistered
2. The memory from the last devm_kmemdup() call gets freed,
hidpp->battery.desc.properties now points to freed memory
3. The first registered power supply class device gets unregistered,
this involves sending a remove uevent to userspace which invokes
power_supply_uevent() to fill the uevent data
4. power_supply_uevent() uses hidpp->battery.desc.properties which
now points to freed memory leading to backtraces like this one:
Sep 22 20:01:35 eric kernel: BUG: unable to handle page fault for address: ffffb2140e017f08
...
Sep 22 20:01:35 eric kernel: Workqueue: usb_hub_wq hub_event
Sep 22 20:01:35 eric kernel: RIP: 0010:power_supply_uevent+0xee/0x1d0
...
Sep 22 20:01:35 eric kernel: ? asm_exc_page_fault+0x26/0x30
Sep 22 20:01:35 eric kernel: ? power_supply_uevent+0xee/0x1d0
Sep 22 20:01:35 eric kernel: ? power_supply_uevent+0x10d/0x1d0
Sep 22 20:01:35 eric kernel: dev_uevent+0x10f/0x2d0
Sep 22 20:01:35 eric kernel: kobject_uevent_env+0x291/0x680
Sep 22 20:01:35 eric kernel: power_supply_unregister+0x8e/0xa0
Sep 22 20:01:35 eric kernel: release_nodes+0x3d/0xb0
Sep 22 20:01:35 eric kernel: devres_release_group+0xfc/0x130
Sep 22 20:01:35 eric kernel: hid_device_remove+0x56/0xa0
Sep 22 20:01:35 eric kernel: device_release_driver_internal+0x19f/0x200
Sep 22 20:01:35 eric kernel: bus_remove_device+0xc6/0x130
Sep 22 20:01:35 eric kernel: device_del+0x15c/0x3f0
Sep 22 20:01:35 eric kernel: ? __queue_work+0x1df/0x440
Sep 22 20:01:35 eric kernel: hid_destroy_device+0x4b/0x60
Sep 22 20:01:35 eric kernel: logi_dj_remove+0x9a/0x100 [hid_logitech_dj 5c91534a0ead2b65e04dd799a0437e3b99b21bc4]
Sep 22 20:01:35 eric kernel: hid_device_remove+0x44/0xa0
Sep 22 20:01:35 eric kernel: device_release_driver_internal+0x19f/0x200
Sep 22 20:01:35 eric kernel: bus_remove_device+0xc6/0x130
Sep 22 20:01:35 eric kernel: device_del+0x15c/0x3f0
Sep 22 20:01:35 eric kernel: ? __queue_work+0x1df/0x440
Sep 22 20:01:35 eric kernel: hid_destroy_device+0x4b/0x60
Sep 22 20:01:35 eric kernel: usbhid_disconnect+0x47/0x60 [usbhid 727dcc1c0b94e6b4418727a468398ac3bca492f3]
Sep 22 20:01:35 eric kernel: usb_unbind_interface+0x90/0x270
Sep 22 20:01:35 eric kernel: device_release_driver_internal+0x19f/0x200
Sep 22 20:01:35 eric kernel: bus_remove_device+0xc6/0x130
Sep 22 20:01:35 eric kernel: device_del+0x15c/0x3f0
Sep 22 20:01:35 eric kernel: ? kobject_put+0xa0/0x1d0
Sep 22 20:01:35 eric kernel: usb_disable_device+0xcd/0x1e0
Sep 22 20:01:35 eric kernel: usb_disconnect+0xde/0x2c0
Sep 22 20:01:35 eric kernel: usb_disconnect+0xc3/0x2c0
Sep 22 20:01:35 eric kernel: hub_event+0xe80/0x1c10
There have been quite a few bug reports (see Link tags) about this crash.
Fix all the TOCTOU issues, including the really bad power-supply related
system crash on USB disconnect, by making probe() use the workqueue for
running hidpp_connect_event() too, so that it can never run more then once.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2227221
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2227968
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2227968
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2242189
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217412#c58
Cc: [email protected]
Signed-off-by: Hans de Goede <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Benjamin Tissoires <[email protected]>
|
|
mismatch warning
As described in the added code comment, a reference to .exit.text is ok
for drivers registered via module_platform_driver_probe(). Make this
explicit to prevent a section mismatch warning:
WARNING: modpost: drivers/platform/x86/hp/hp-wmi: section mismatch in reference: hp_wmi_driver+0x8 (section: .data) -> hp_wmi_bios_remove (section: .exit.text)
Fixes: c165b80cfecc ("hp-wmi: fix handling of platform device")
Signed-off-by: Uwe Kleine-König <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Hans de Goede <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: More fixes for v6.6
Some additional fixes for v6.6, some fairly unremarkable driver specific
ones and a couple of minor core fixes for error handling and improved
logging.
|
|
Adopt FlexCAN stop mode to new A1 revision of imx93 SoCs.
Link: https://lore.kernel.org/all/[email protected]
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
Fix id2_register content for tcan4553. This slipped through my testing.
Reported-by: Sean Anderson <[email protected]>
Closes: https://lore.kernel.org/lkml/[email protected]/
Fixes: 142c6dc6d9d7 ("can: tcan4x5x: Add support for tcan4552/4553")
Signed-off-by: Markus Schneider-Pargmann <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Link: https://lore.kernel.org/all/[email protected]
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
IMX93 A0 chip involve the internal q-channel handshake in LPCG and
CCM to automatically handle the Flex-CAN IPG STOP signal. Only after
FLEX-CAN enter stop mode then can support the self-wakeup feature.
But meet issue when do the continue system PM stress test. When config
the CAN as wakeup source, the first time after system suspend, any data
on CAN bus can wakeup the system, this is as expect. But the second time
when system suspend, data on CAN bus can't wakeup the system. If continue
this test, we find in odd time system enter suspend, CAN can wakeup the
system, but in even number system enter suspend, CAN can't wakeup the
system. IC find a bug in the auto stop mode logic, and can't fix it easily.
So for the new imx93 A1, IC drop the auto stop mode and involve the
GPR to support stop mode (used before). IC define a bit in GPR which can
trigger the IPG STOP signal to Flex-CAN, let it go into stop mode.
And NXP claim to drop IMX93 A0, and only support IMX93 A1. So this patch
remove the auto stop mode, and add flag FLEXCAN_QUIRK_SETUP_STOP_MODE_GPR
to imx93.
Signed-off-by: Haibo Chen <[email protected]>
Link: https://lore.kernel.org/all/[email protected]
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
Upstream commit 717c6ec241b5 ("can: sja1000: Prevent overrun stalls with
a soft reset on Renesas SoCs") fixes an issue with Renesas own SJA1000
CAN controller reception: the Rx buffer is only 5 messages long, so when
the bus loaded (eg. a message every 50us), overrun may easily
happen. Upon an overrun situation, due to a possible internal crosstalk
situation, the controller enters a frozen state which only can be
unlocked with a soft reset (experimentally). The solution was to offload
a call to sja1000_start() in a threaded handler. This needs to happen in
process context as this operation requires to sleep. sja1000_start()
basically enters "reset mode", performs a proper software reset and
returns back into "normal mode".
Since this fix was introduced, we no longer observe any stalls in
reception. However it was sporadically observed that the transmit path
would now freeze. Further investigation blamed the fix mentioned above,
and especially the reset operation. Reproducing the reset in a loop
helped identifying what could possibly go wrong. The sja1000 is a single
Tx queue device, which leverages the netdev helpers to process one Tx
message at a time. The logic is: the queue is stopped, the message sent
to the transceiver, once properly transmitted the controller sets a
status bit which triggers an interrupt, in the interrupt handler the
transmission status is checked and the queue woken up. Unfortunately, if
an overrun happens, we might perform the soft reset precisely between
the transmission of the buffer to the transceiver and the advent of the
transmission status bit. We would then stop the transmission operation
without re-enabling the queue, leading to all further transmissions to
be ignored.
The reset interrupt can only happen while the device is "open", and
after a reset we anyway want to resume normal operations, no matter if a
packet to transmit got dropped in the process, so we shall wake up the
queue. Restarting the device and waking-up the queue is exactly what
sja1000_set_mode(CAN_MODE_START) does. In order to be consistent about
the queue state, we must acquire a lock both in the reset handler and in
the transmit path to ensure serialization of both operations. It turns
out, a lock is already held when entering the transmit path, so we can
just acquire/release it as well with the regular net helpers inside the
threaded interrupt handler and this way we should be safe. As the
reset handler might still be called after the transmission of a frame to
the transceiver but before it actually gets transmitted, we must ensure
we don't leak the skb, so we free it (the behavior is consistent, no
matter if there was an skb on the stack or not).
Fixes: 717c6ec241b5 ("can: sja1000: Prevent overrun stalls with a soft reset on Renesas SoCs")
Cc: [email protected]
Signed-off-by: Miquel Raynal <[email protected]>
Link: https://lore.kernel.org/all/[email protected]
[mkl: fixed call to can_free_echo_skb()]
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
imx93 A0 chip use the internal q-channel handshake signal in LPCG
and CCM to automatically handle the Flex-CAN stop mode. But this
method meet issue when do the system PM stress test. IC can't fix
it easily. So in the new imx93 A1 chip, IC drop this method, and
involve back the old way，use the GPR method to trigger the Flex-CAN
stop mode signal. Now NXP claim to drop imx93 A0, and only support
imx93 A1. So here add the stop mode through GPR.
This patch also fix a typo for aonmix_ns_gpr.
Signed-off-by: Haibo Chen <[email protected]>
Link: https://lore.kernel.org/all/[email protected]
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
When adding the RISCV option I didn't gate it behind ARCH_SUNXI.
As a result this option shows up with Allwinner support isn't enabled.
Fix that by requiring ARCH_SUNXI to be set if RISCV is set.
Fixes: 8abb95250ae6 ("can: sun4i_can: Add support for the Allwinner D1")
Reported-by: Geert Uytterhoeven <[email protected]>
Closes: https://lore.kernel.org/linux-sunxi/CAMuHMdV2m54UAH0X2dG7stEg=grFihrdsz4+o7=_DpBMhjTbkw@mail.gmail.com/
Signed-off-by: John Watts <[email protected]>
Reviewed-by: Geert Uytterhoeven <[email protected]>
Link: https://lore.kernel.org/all/[email protected]
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
With patch [1], isotp_poll was updated to also queue the poller in the
so->wait queue, which is used for send state changes. Since the queue
now also contains polling tasks that are not interested in sending, the
queue fill state can no longer be used as an indication of send
readiness. As a consequence, nonblocking writes can lead to a race and
lock-up of the socket if there is a second task polling the socket in
parallel.
With this patch, isotp_sendmsg does not consult wq_has_sleepers but
instead tries to atomically set so->tx.state and waits on so->wait if it
is unable to do so. This behavior is in alignment with isotp_poll, which
also checks so->tx.state to determine send readiness.
V2:
- Revert direct exit to goto err_event_drop
[1] https://lore.kernel.org/all/[email protected]
Reported-by: Maxime Jayat <[email protected]>
Closes: https://lore.kernel.org/linux-can/[email protected]/
Signed-off-by: Lukas Magel <[email protected]>
Reviewed-by: Oliver Hartkopp <[email protected]>
Fixes: 79e19fa79cb5 ("can: isotp: isotp_ops: fix poll() to not report false EPOLLOUT events")
Link: https://github.com/pylessard/python-udsoncan/issues/178#issuecomment-1743786590
Link: https://lore.kernel.org/all/[email protected]
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
commit d61491a51f7e ("net/sched: cls_u32: Replace one-element array
with flexible-array member") incorrecly replaced an instance of
`sizeof(*tp_c)` with `struct_size(tp_c, hlist->ht, 1)`. This results
in a an over-allocation of 8 bytes.
This change is wrong because `hlist` in `struct tc_u_common` is a
pointer:
net/sched/cls_u32.c:
struct tc_u_common {
struct tc_u_hnode __rcu *hlist;
void *ptr;
int refcnt;
struct idr handle_idr;
struct hlist_node hnode;
long knodes;
};
So, the use of `struct_size()` makes no sense: we don't need to allocate
any extra space for a flexible-array member. `sizeof(*tp_c)` is just fine.
So, `struct_size(tp_c, hlist->ht, 1)` translates to:
sizeof(*tp_c) + sizeof(tp_c->hlist->ht) ==
sizeof(struct tc_u_common) + sizeof(struct tc_u_knode *) ==
144 + 8 == 0x98 (byes)
^^^
|
unnecessary extra
allocation size
$ pahole -C tc_u_common net/sched/cls_u32.o
struct tc_u_common {
struct tc_u_hnode * hlist; /* 0 8 */
void * ptr; /* 8 8 */
int refcnt; /* 16 4 */
/* XXX 4 bytes hole, try to pack */
struct idr handle_idr; /* 24 96 */
/* --- cacheline 1 boundary (64 bytes) was 56 bytes ago --- */
struct hlist_node hnode; /* 120 16 */
/* --- cacheline 2 boundary (128 bytes) was 8 bytes ago --- */
long int knodes; /* 136 8 */
/* size: 144, cachelines: 3, members: 6 */
/* sum members: 140, holes: 1, sum holes: 4 */
/* last cacheline: 16 bytes */
};
And with `sizeof(*tp_c)`, we have:
sizeof(*tp_c) == sizeof(struct tc_u_common) == 144 == 0x90 (bytes)
which is the correct and original allocation size.
Fix this issue by replacing `struct_size(tp_c, hlist->ht, 1)` with
`sizeof(*tp_c)`, and avoid allocating 8 too many bytes.
The following difference in binary output is expected and reflects the
desired change:
| net/sched/cls_u32.o
| @@ -6148,7 +6148,7 @@
| include/linux/slab.h:599
| 2cf5: mov 0x0(%rip),%rdi # 2cfc <u32_init+0xfc>
| 2cf8: R_X86_64_PC32 kmalloc_caches+0xc
|- 2cfc: mov $0x98,%edx
|+ 2cfc: mov $0x90,%edx
Reported-by: Alejandro Colomar <[email protected]>
Closes: https://lore.kernel.org/lkml/[email protected]/
Signed-off-by: Gustavo A. R. Silva <[email protected]>
Acked-by: Jamal Hadi Salim <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Marek Behún says:
====================
net: dsa: qca8k: fix qca8k driver for Turris 1.x
this is v2 of
https://lore.kernel.org/netdev/[email protected]/
Changes since v1:
- fixed a typo in commit message noticed by Simon Horman
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
PHYs via management frames
Besides the QCA8337 switch the Turris 1.x device has on it's MDIO bus
also Micron ethernet PHY (dedicated to the WAN port).
We've been experiencing a strange behavior of the WAN ethernet
interface, wherein the WAN PHY started timing out the MDIO accesses, for
example when the interface was brought down and then back up.
Bisecting led to commit 2cd548566384 ("net: dsa: qca8k: add support for
phy read/write with mgmt Ethernet"), which added support to access the
QCA8337 switch's internal PHYs via management ethernet frames.
Connecting the MDIO bus pins onto an oscilloscope, I was able to see
that the MDIO bus was active whenever a request to read/write an
internal PHY register was done via an management ethernet frame.
My theory is that when the switch core always communicates with the
internal PHYs via the MDIO bus, even when externally we request the
access via ethernet. This MDIO bus is the same one via which the switch
and internal PHYs are accessible to the board, and the board may have
other devices connected on this bus. An ASCII illustration may give more
insight:
+---------+
+----| |
| | WAN PHY |
| +--| |
| | +---------+
| |
| | +----------------------------------+
| | | QCA8337 |
MDC | | | +-------+ |
------o-+--|--------o------------o--| | |
MDIO | | | | | PHY 1 |-|--to RJ45
--------o--|---o----+---------o--+--| | |
| | | | | +-------+ |
| +-------------+ | o--| | |
| | MDIO MDC | | | | PHY 2 |-|--to RJ45
eth1 | | | o--+--| | |
-----------|-|port0 | | | +-------+ |
| | | | o--| | |
| | switch core | | | | PHY 3 |-|--to RJ45
| +-------------+ o--+--| | |
| | | +-------+ |
| | o--| ... | |
+----------------------------------+
When we send a request to read an internal PHY register via an ethernet
management frame via eth1, the switch core receives the ethernet frame
on port 0 and then communicates with the internal PHY via MDIO. At this
time, other potential devices, such as the WAN PHY on Turris 1.x, cannot
use the MDIO bus, since it may cause a bus conflict.
Fix this issue by locking the MDIO bus even when we are accessing the
PHY registers via ethernet management frames.
Fixes: 2cd548566384 ("net: dsa: qca8k: add support for phy read/write with mgmt Ethernet")
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Christian Marangi <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Commit c766e077d927 ("net: dsa: qca8k: convert to regmap read/write
API") introduced bulk read/write methods to qca8k's regmap.
The regmap bulk read/write methods get the register address in a buffer
passed as a void pointer parameter (the same buffer contains also the
read/written values). The register address occupies only as many bytes
as it requires at the beginning of this buffer. For example if the
.reg_bits member in regmap_config is 16 (as is the case for this
driver), the register address occupies only the first 2 bytes in this
buffer, so it can be cast to u16.
But the original commit implementing these bulk read/write methods cast
the buffer to u32:
u32 reg = *(u32 *)reg_buf & U16_MAX;
taking the first 4 bytes. This works on little endian systems where the
first 2 bytes of the buffer correspond to the low 16-bits, but it
obviously cannot work on big endian systems.
Fix this by casting the beginning of the buffer to u16 as
u32 reg = *(u16 *)reg_buf;
Fixes: c766e077d927 ("net: dsa: qca8k: convert to regmap read/write API")
Signed-off-by: Marek Behún <[email protected]>
Tested-by: Christian Marangi <[email protected]>
Reviewed-by: Christian Marangi <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Vladimir Oltean says:
====================
Fixes for lynx-28g PHY driver
This series fixes some issues in the Lynx 28G SerDes driver, namely an
oops when unloading the module, a race between the periodic workqueue
and the PHY API, and a race between phy_set_mode_ext() calls on multiple
lanes on the same SerDes.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
The protocol converter configuration registers PCC8, PCCC, PCCD
(implemented by the driver), as well as others, control protocol
converters from multiple lanes (each represented as a different
struct phy). So, if there are simultaneous calls to phy_set_mode_ext()
to lanes sharing the same PCC register (either for the "old" or for the
"new" protocol), corruption of the values programmed to hardware is
possible, because lynx_28g_rmw() has no locking.
Add a spinlock in the struct lynx_28g_priv shared by all lanes, and take
the global spinlock from the phy_ops :: set_mode() implementation. There
are no other callers which modify PCC registers.
Fixes: 8f73b37cf3fb ("phy: add support for the Layerscape SerDes 28G")
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
lynx_28g_cdr_lock_check() runs once per second in a workqueue to reset
the lane receiver if the CDR has not locked onto bit transitions in the
RX stream. But the PHY consumer may do stuff with the PHY simultaneously,
and that isn't okay. Block concurrent generic PHY calls by holding the
PHY mutex from this workqueue.
Fixes: 8f73b37cf3fb ("phy: add support for the Layerscape SerDes 28G")
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The blamed commit added the CDR check work item but didn't cancel it on
the remove path. Fix this by adding a remove function which takes care
of it.
Fixes: 8f73b37cf3fb ("phy: add support for the Layerscape SerDes 28G")
Signed-off-by: Ioana Ciornei <[email protected]>
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Intel RVP board (0x12cc) has Headset Mic issue for reboot.
If system plugged headset when system reboot the headset Mic was gone.
Fixes: 1a93f10c5b12 ("ALSA: hda/realtek: Add "Intel Reference board" and "NUC 13" SSID in the ALC256")
Signed-off-by: Kailang Yang <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
When a Opencomm2 Headset is connected to a Bluetooth USB dongle,
the audio playback functions properly, but the microphone does not work.
In the dmesg logs, there are messages indicating that the init_pitch
function fails when the capture process begins.
The microphone only functions when the ep pitch control is not set.
Toggling the pitch control off bypasses the init_piatch function
and allows the microphone to work.
Signed-off-by: WhaleChang <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
There is an unlikely but possible double free when loading firmware,
and a missing free calls if a firmware is successfully requested but
the coefficient file request fails, leading to the fallback firmware
request occurring without clearing the previously loaded firmware.
Fixes: cd40dad2ca91 ("ALSA: hda: cs35l41: Ensure firmware/tuning pairs are always loaded")
Reported-by: kernel test robot <[email protected]>
Reported-by: Dan Carpenter <[email protected]>
Closes: https://lore.kernel.org/r/[email protected]/
Signed-off-by: Stefan Binding <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
Eric has reported that commit dabc8b207566 ("quota: fix dqput() to
follow the guarantees dquot_srcu should provide") heavily increases
runtime of generic/270 xfstest for ext4 in nojournal mode. The reason
for this is that ext4 in nojournal mode leaves dquots dirty until the last
dqput() and thus the cleanup done in quota_release_workfn() has to write
them all. Due to the way quota_release_workfn() is written this results
in synchronize_srcu() call for each dirty dquot which makes the dquot
cleanup when turning quotas off extremely slow.
To be able to avoid synchronize_srcu() for each dirty dquot we need to
rework how we track dquots to be cleaned up. Instead of keeping the last
dquot reference while it is on releasing_dquots list, we drop it right
away and mark the dquot with new DQ_RELEASING_B bit instead. This way we
can we can remove dquot from releasing_dquots list when new reference to
it is acquired and thus there's no need to call synchronize_srcu() each
time we drop dq_list_lock.
References: https://lore.kernel.org/all/ZRytn6CxFK2oECUt@debian-BULLSEYE-live-builder-AMD64
Reported-by: Eric Whitney <[email protected]>
Fixes: dabc8b207566 ("quota: fix dqput() to follow the guarantees dquot_srcu should provide")
CC: [email protected]
Signed-off-by: Jan Kara <[email protected]>
|
|
A recent commit reordered probe so that the interrupt line is now
requested before making sure that the device exists.
This breaks machines like the Lenovo ThinkPad X13s which rely on the
HID driver to probe second-source devices and only register the variant
that is actually populated. Specifically, the interrupt line may now
already be (temporarily) claimed when doing asynchronous probing of the
touchpad:
genirq: Flags mismatch irq 191. 00082008 (hid-over-i2c) vs. 00082008 (hid-over-i2c)
i2c_hid_of 21-0015: Could not register for hid-over-i2c interrupt, irq = 191, ret = -16
i2c_hid_of: probe of 21-0015 failed with error -16
Fix this by restoring the old behaviour of first making sure the device
exists before requesting the interrupt line.
Note that something like this should probably be implemented also for
"panel followers", whose actual probe is currently effectively deferred
until the DRM panel is probed (e.g. by powering down the device after
making sure it exists and only then register it as a follower).
Fixes: 675cd877c952 ("HID: i2c-hid: Rearrange probe() to power things up later")
Cc: Douglas Anderson <[email protected]>
Cc: Maxime Ripard <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
Tested-by: Dennis Gilmore <[email protected]>
Reviewed-by: Douglas Anderson <[email protected]>
Tested-by: Douglas Anderson <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Benjamin Tissoires <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs
Pull erofs fixes from Gao Xiang:
- Fix a memory leak issue when using LZMA global compressed
deduplication
- Fix empty device tags in flatdev mode
- Update documentation for recent new features
* tag 'erofs-for-6.6-rc5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs:
erofs: update documentation
erofs: allow empty device tags in flatdev mode
erofs: fix memory leak of LZMA global compressed deduplication
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID fixes from Jiri Kosina:
- power management fix for intel-ish-hid (Srinivas Pandruvada)
- power management fix for hid-nintendo (Martino Fontana)
- error handling fixes for nvidia-shield (Christophe JAILLET)
- memory leak fix for hid-sony (Christophe JAILLET)
- fix for slab out-of-bound write in hid-holtek (Ma Ke)
- other assorted smaller fixes and device ID / quirk entry additions
* tag 'for-linus-2023100502' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: Add quirk to ignore the touchscreen battery on HP ENVY 15-eu0556ng
HID: intel-ish-hid: ipc: Disable and reenable ACPI GPE bit
HID: sony: remove duplicate NULL check before calling usb_free_urb()
HID: nintendo: reinitialize USB Pro Controller after resuming from suspend
HID: nvidia-shield: Fix some missing function calls() in the probe error handling path
HID: nvidia-shield: Fix a missing led_classdev_unregister() in the probe error handling path
HID: multitouch: Add required quirk for Synaptics 0xcd7e device
HID: nvidia-shield: Select POWER_SUPPLY Kconfig option
HID: holtek: fix slab-out-of-bounds Write in holtek_kbd_input_event
HID: nvidia-shield: add LEDS_CLASS dependency
HID: logitech-hidpp: Add Bluetooth ID for the Logitech M720 Triathlon mouse
HID: steelseries: Fix signedness bug in steelseries_headset_arctis_1_fetch_battery()
HID: sony: Fix a potential memory leak in sony_probe()
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Short summary of fixes pull:
* test: Fix kunit release
* panel-orientation: Add quirk for One Mix 25
* nouveau:
* Report IB limit via getparams
* Replace some magic numbers with constants
* Clean up
Signed-off-by: Dave Airlie <[email protected]>
From: Thomas Zimmermann <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/20231005092632.GA17332@linux-uq9g
|
|
https://gitlab.freedesktop.org/agd5f/linux into drm-fixes
amd-drm-fixes-6.6-2023-10-04:
amdgpu:
- Add missing unique_id for GC 11.0.3
- Fix memory leak in FRU error path
- Fix PCIe link reporting on some SMU 11 parts
- Fix ACPI _PR3 detection
- Fix DISPCLK WDIVIDER handling in OTG code
Signed-off-by: Dave Airlie <[email protected]>
From: Alex Deucher <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
A skcipher_request object is made up of struct skcipher_request
followed by a variable-sized trailer. The allocation of the
skcipher_request and IV in crypt_iv_eboiv_gen is missing the
memory for struct skcipher_request. Fix it by adding it to
reqsize.
Fixes: e3023094dffb ("dm crypt: Avoid using MAX_CIPHER_BLOCKSIZE")
Cc: <[email protected]> #6.5+
Reported-by: Tatu Heikkilä <[email protected]>
Reviewed-by: Mike Snitzer <[email protected]>
Signed-off-by: Herbert Xu <[email protected]>
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
- Fix for OpenGL CTS regression on Compute Shaders (Nirmoy)
- Fix for default engines initialization (Mathias)
- Fix TLB invalidation for Multi-GT devices (Chris)
Signed-off-by: Dave Airlie <[email protected]>
From: Rodrigo Vivi <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
I received a bug report with the following signature:
[ 1759.937637] BUG: unable to handle page fault for address: ffffffffffffffe8
[ 1759.944564] #PF: supervisor read access in kernel mode
[ 1759.949732] #PF: error_code(0x0000) - not-present page
[ 1759.954901] PGD 7ab615067 P4D 7ab615067 PUD 7ab617067 PMD 0
[ 1759.960596] Oops: 0000 1 PREEMPT SMP PTI
[ 1759.964804] CPU: 15 PID: 109 Comm: cpuhp/15 Kdump: loaded Tainted: G X ------- — 5.14.0-362.3.1.el9_3.x86_64 #1
[ 1759.976609] Hardware name: HPE ProLiant DL380 Gen10/ProLiant DL380 Gen10, BIOS U30 06/20/2018
[ 1759.985181] RIP: 0010:io_wq_for_each_worker.isra.0+0x24/0xa0
[ 1759.990877] Code: 90 90 90 90 90 90 0f 1f 44 00 00 41 56 41 55 41 54 55 48 8d 6f 78 53 48 8b 47 78 48 39 c5 74 4f 49 89 f5 49 89 d4 48 8d 58 e8 <8b> 13 85 d2 74 32 8d 4a 01 89 d0 f0 0f b1 0b 75 5c 09 ca 78 3d 48
[ 1760.009758] RSP: 0000:ffffb6f403603e20 EFLAGS: 00010286
[ 1760.015013] RAX: 0000000000000000 RBX: ffffffffffffffe8 RCX: 0000000000000000
[ 1760.022188] RDX: ffffb6f403603e50 RSI: ffffffffb11e95b0 RDI: ffff9f73b09e9400
[ 1760.029362] RBP: ffff9f73b09e9478 R08: 000000000000000f R09: 0000000000000000
[ 1760.036536] R10: ffffffffffffff00 R11: ffffb6f403603d80 R12: ffffb6f403603e50
[ 1760.043712] R13: ffffffffb11e95b0 R14: ffffffffb28531e8 R15: ffff9f7a6fbdf548
[ 1760.050887] FS: 0000000000000000(0000) GS:ffff9f7a6fbc0000(0000) knlGS:0000000000000000
[ 1760.059025] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 1760.064801] CR2: ffffffffffffffe8 CR3: 00000007ab610002 CR4: 00000000007706e0
[ 1760.071976] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 1760.079150] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 1760.086325] PKRU: 55555554
[ 1760.089044] Call Trace:
[ 1760.091501] <TASK>
[ 1760.093612] ? show_trace_log_lvl+0x1c4/0x2df
[ 1760.097995] ? show_trace_log_lvl+0x1c4/0x2df
[ 1760.102377] ? __io_wq_cpu_online+0x54/0xb0
[ 1760.106584] ? __die_body.cold+0x8/0xd
[ 1760.110356] ? page_fault_oops+0x134/0x170
[ 1760.114479] ? kernelmode_fixup_or_oops+0x84/0x110
[ 1760.119298] ? exc_page_fault+0xa8/0x150
[ 1760.123247] ? asm_exc_page_fault+0x22/0x30
[ 1760.127458] ? __pfx_io_wq_worker_affinity+0x10/0x10
[ 1760.132453] ? __pfx_io_wq_worker_affinity+0x10/0x10
[ 1760.137446] ? io_wq_for_each_worker.isra.0+0x24/0xa0
[ 1760.142527] __io_wq_cpu_online+0x54/0xb0
[ 1760.146558] cpuhp_invoke_callback+0x109/0x460
[ 1760.151029] ? __pfx_io_wq_cpu_offline+0x10/0x10
[ 1760.155673] ? __pfx_smpboot_thread_fn+0x10/0x10
[ 1760.160320] cpuhp_thread_fun+0x8d/0x140
[ 1760.164266] smpboot_thread_fn+0xd3/0x1a0
[ 1760.168297] kthread+0xdd/0x100
[ 1760.171457] ? __pfx_kthread+0x10/0x10
[ 1760.175225] ret_from_fork+0x29/0x50
[ 1760.178826] </TASK>
[ 1760.181022] Modules linked in: rpcsec_gss_krb5 auth_rpcgss nfsv4 dns_resolver nfs lockd grace fscache netfs rfkill sunrpc vfat fat dm_multipath intel_rapl_msr intel_rapl_common isst_if_common ipmi_ssif nfit libnvdimm mgag200 i2c_algo_bit ioatdma drm_shmem_helper drm_kms_helper acpi_ipmi syscopyarea x86_pkg_temp_thermal sysfillrect ipmi_si intel_powerclamp sysimgblt ipmi_devintf coretemp acpi_power_meter ipmi_msghandler rapl pcspkr dca intel_pch_thermal intel_cstate ses lpc_ich intel_uncore enclosure hpilo mei_me mei acpi_tad fuse drm xfs sd_mod sg bnx2x nvme nvme_core crct10dif_pclmul crc32_pclmul nvme_common ghash_clmulni_intel smartpqi tg3 t10_pi mdio uas libcrc32c crc32c_intel scsi_transport_sas usb_storage hpwdt wmi dm_mirror dm_region_hash dm_log dm_mod
[ 1760.248623] CR2: ffffffffffffffe8
A cpu hotplug callback was issued before wq->all_list was initialized.
This results in a null pointer dereference. The fix is to fully setup
the io_wq before calling cpuhp_state_add_instance_nocalls().
Signed-off-by: Jeff Moyer <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jens Axboe <[email protected]>
|
|
When cpufreq's policy is 'single', there is a scenario that will
cause sg_policy's next_freq to be unable to update.
When the CPU's util is always max, the cpufreq will be max,
and then if we change the policy's scaling_max_freq to be a
lower freq, indeed, the sg_policy's next_freq need change to
be the lower freq, however, because the cpu_is_busy, the next_freq
would keep the max_freq.
For example:
The cpu7 is a single CPU:
unisoc:/sys/devices/system/cpu/cpufreq/policy7 # while true;do done& [1] 4737
unisoc:/sys/devices/system/cpu/cpufreq/policy7 # taskset -p 80 4737
pid 4737's current affinity mask: ff
pid 4737's new affinity mask: 80
unisoc:/sys/devices/system/cpu/cpufreq/policy7 # cat scaling_max_freq
2301000
unisoc:/sys/devices/system/cpu/cpufreq/policy7 # cat scaling_cur_freq
2301000
unisoc:/sys/devices/system/cpu/cpufreq/policy7 # echo 2171000 > scaling_max_freq
unisoc:/sys/devices/system/cpu/cpufreq/policy7 # cat scaling_max_freq
2171000
At this time, the sg_policy's next_freq would stay at 2301000, which
is wrong.
To fix this, add a check for the ->need_freq_update flag.
[ mingo: Clarified the changelog. ]
Co-developed-by: Guohua Yan <[email protected]>
Signed-off-by: Xuewen Yan <[email protected]>
Signed-off-by: Guohua Yan <[email protected]>
Signed-off-by: Ingo Molnar <[email protected]>
Acked-by: "Rafael J. Wysocki" <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Add information for the Positivo C4128B, a notebook/tablet convertible.
Link: https://github.com/onitake/gsl-firmware/pull/217
Signed-off-by: Renan Guilherme Lebre Ramos <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Hans de Goede <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
|