| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The driver on R8A77995 requests the same IRQ twice since
platform_get_resource() is always called for the 1st IRQ resource.
Fixes: 1969d9dc2079 ("thermal: rcar_thermal: add r8a77995 support")
Signed-off-by: Sergei Shtylyov <[email protected]>
Reviewed-by: Geert Uytterhoeven <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Reviewed-by: Daniel Lezcano <[email protected]>
Signed-off-by: Eduardo Valentin <[email protected]>
|
|
Older versions of bintutils do not allow symbol math across different
segments on sparc:
====================
Assembler messages:
99: Error: operation combines symbols in different segments
====================
This is controlled by whether or not DIFF_EXPR_OK is defined in
gas/config/tc-*.h and for sparc this was not the case until mid-2017.
So we have to patch between %stick and %tick another way.
Do what powerpc does and emit two versions of the relevant functions,
one using %tick and one using %stick, and patch the symbols in the
dynamic symbol table.
Fixes: 2f6c9bf31a0b ("sparc: Improve VDSO instruction patching.")
Reported-by: Meelis Roos <[email protected]>
Tested-by: Meelis Roos <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Since commit 2d29c9f89fcd ("block, bfq: improve asymmetric scenarios
detection"), a scenario is defined asymmetric when one of the
following conditions holds:
- active bfq_queues have different weights
- one or more group of entities (bfq_queue or other groups of entities)
are active
bfq grants fairness and low latency also in such asymmetric scenarios,
by plugging the dispatching of I/O if the bfq_queue in service happens
to be temporarily idle. This plugging may lower throughput, so it is
important to do it only when strictly needed.
By mistake, in commit '2d29c9f89fcd' ("block, bfq: improve asymmetric
scenarios detection") the num_active_groups counter was firstly
incremented and subsequently decremented at any entity (group or
bfq_queue) weight change.
This is useless, because only transitions from active to inactive and
vice versa matter for that counter. Unfortunately this is also
incorrect in the following case: the entity at issue is a bfq_queue
and it is under weight raising. In fact in this case there is a
spurious increment of the num_active_groups counter.
This spurious increment may cause scenarios to be wrongly detected as
asymmetric, thus causing useless plugging and loss of throughput.
This commit fixes this issue by simply removing the above useless and
wrong increments and decrements.
Fixes: 2d29c9f89fcd ("block, bfq: improve asymmetric scenarios detection")
Tested-by: Oleksandr Natalenko <[email protected]>
Signed-off-by: Federico Motta <[email protected]>
Signed-off-by: Paolo Valente <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
Apparently the kbuild bots missed this one originally, but at least
it caught it now. Fix compilation error:
All errors (new ones prefixed by >>):
drivers/cdrom/gdrom.c: In function 'probe_gdrom':
>> drivers/cdrom/gdrom.c:797:3: error: 'rc' undeclared (first use in this function)
rc = PTR_ERR(gd.gdrom_rq);
^~
drivers/cdrom/gdrom.c:797:3: note: each undeclared identifier is reported only once for each function it appears in
Fixes: ad5fc6bb7221 ("gdrom: convert to blk-mq")
Signed-off-by: Jens Axboe <[email protected]>
|
|
trace_block_getrq() is to indicate a request struct has been allocated
for queue, so put it in right place.
Reviewed-by: Jianchao Wang <[email protected]>
Signed-off-by: Xiaoguang Wang <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
Drivers exposing zoned block devices have to initialize and maintain
correctness (i.e. revalidate) of the device zone bitmaps attached to
the device request queue (seq_zones_bitmap and seq_zones_wlock).
To simplify coding this, introduce a generic helper function
blk_revalidate_disk_zones() suitable for most (and likely all) cases.
This new function always update the seq_zones_bitmap and seq_zones_wlock
bitmaps as well as the queue nr_zones field when called for a disk
using a request based queue. For a disk using a BIO based queue, only
the number of zones is updated since these queues do not have
schedulers and so do not need the zone bitmaps.
With this change, the zone bitmap initialization code in sd_zbc.c can be
replaced with a call to this function in sd_zbc_read_zones(), which is
called from the disk revalidate block operation method.
A call to blk_revalidate_disk_zones() is also added to the null_blk
driver for devices created with the zoned mode enabled.
Finally, to ensure that zoned devices created with dm-linear or
dm-flakey expose the correct number of zones through sysfs, a call to
blk_revalidate_disk_zones() is added to dm_table_set_restrictions().
The zone bitmaps allocated and initialized with
blk_revalidate_disk_zones() are freed automatically from
__blk_release_queue() using the block internal function
blk_queue_free_zone_bitmaps().
Reviewed-by: Hannes Reinecke <[email protected]>
Reviewed-by: Christoph Hellwig <[email protected]>
Reviewed-by: Martin K. Petersen <[email protected]>
Reviewed-by: Mike Snitzer <[email protected]>
Signed-off-by: Damien Le Moal <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
Dispatching a report zones command through the request queue is a major
pain due to the command reply payload rewriting necessary. Given that
blkdev_report_zones() is executing everything synchronously, implement
report zones as a block device file operation instead, allowing major
simplification of the code in many places.
sd, null-blk, dm-linear and dm-flakey being the only block device
drivers supporting exposing zoned block devices, these drivers are
modified to provide the device side implementation of the
report_zones() block device file operation.
For device mappers, a new report_zones() target type operation is
defined so that the upper block layer calls blkdev_report_zones() can
be propagated down to the underlying devices of the dm targets.
Implementation for this new operation is added to the dm-linear and
dm-flakey targets.
Reviewed-by: Hannes Reinecke <[email protected]>
Signed-off-by: Christoph Hellwig <[email protected]>
[Damien]
* Changed method block_device argument to gendisk
* Various bug fixes and improvements
* Added support for null_blk, dm-linear and dm-flakey.
Reviewed-by: Martin K. Petersen <[email protected]>
Reviewed-by: Mike Snitzer <[email protected]>
Signed-off-by: Damien Le Moal <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
Expose through sysfs the nr_zones field of struct request_queue.
Exposing this value helps in debugging disk issues as well as
facilitating scripts based use of the disk (e.g. blktests).
For zoned block devices, the nr_zones field indicates the total number
of zones of the device calculated using the known disk capacity and
zone size. This number of zones is always 0 for regular block devices.
Since nr_zones is defined conditionally with CONFIG_BLK_DEV_ZONED,
introduce the blk_queue_nr_zones() function to return the correct value
for any device, regardless if CONFIG_BLK_DEV_ZONED is set.
Reviewed-by: Christoph Hellwig <[email protected]>
Reviewed-by: Hannes Reinecke <[email protected]>
Signed-off-by: Damien Le Moal <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
There is no need to synchronously execute all REQ_OP_ZONE_RESET BIOs
necessary to reset a range of zones. Similarly to what is done for
discard BIOs in blk-lib.c, all zone reset BIOs can be chained and
executed asynchronously and a synchronous call done only for the last
BIO of the chain.
Modify blkdev_reset_zones() to operate similarly to
blkdev_issue_discard() using the next_bio() helper for chaining BIOs. To
avoid code duplication of that function in blk_zoned.c, rename
next_bio() into blk_next_bio() and declare it as a block internal
function in blk.h.
Reviewed-by: Christoph Hellwig <[email protected]>
Reviewed-by: Hannes Reinecke <[email protected]>
Signed-off-by: Damien Le Moal <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
Get a zoned block device total number of zones. The device can be a
partition of the whole device. The number of zones is always 0 for
regular block devices.
Reviewed-by: Hannes Reinecke <[email protected]>
Reviewed-by: Christoph Hellwig <[email protected]>
Signed-off-by: Damien Le Moal <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
Get a zoned block device zone size in number of 512 B sectors.
The zone size is always 0 for regular block devices.
Reviewed-by: Hannes Reinecke <[email protected]>
Reviewed-by: Christoph Hellwig <[email protected]>
Signed-off-by: Damien Le Moal <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
There is no point in allocating more zone descriptors than the number of
zones a block device has for doing a zone report. Avoid doing that in
blkdev_report_zones_ioctl() by limiting the number of zone decriptors
allocated internally to process the user request.
Reviewed-by: Christoph Hellwig <[email protected]>
Reviewed-by: Hannes Reinecke <[email protected]>
Signed-off-by: Damien Le Moal <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
Introduce the blkdev_nr_zones() helper function to get the total
number of zones of a zoned block device. This number is always 0 for a
regular block device (q->limits.zoned == BLK_ZONED_NONE case).
Replace hard-coded number of zones calculation in dmz_get_zoned_device()
with a call to this helper.
Reviewed-by: Christoph Hellwig <[email protected]>
Reviewed-by: Hannes Reinecke <[email protected]>
Signed-off-by: Damien Le Moal <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
The unsigned 32 bits overflow check for the zone size value is already
done within sd_zbc_check_zones() with the test:
} else if (logical_to_sectors(sdkp->device, zone_blocks) > UINT_MAX) {
so there is no need to check again for an out of range value in
sd_zbc_read_zones(). Simplify the code and fix sd_zbc_check_zones()
error return to -EFBIG instead of -ENODEV if the zone size is too large.
Change the return type of sd_zbc_check_zones() to an int for the error
code and return the zone size (zone_blocks) through a u32 pointer to
avoid overflowing the signed 32 return value.
Reviewed-by: Hannes Reinecke <[email protected]>
Acked-by: Martin K. Petersen <[email protected]>
Reviewed-by: Christoph Hellwig <[email protected]>
Signed-off-by: Damien Le Moal <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
Handling checks of ZBC device capacity using the max_lba field of the
REPORT ZONES command reply for disks with rc_basis == 0 can be done
using the same report zones command reply used to check the "same"
field.
Avoid executing a report zones command solely to check the disk capacity
by merging sd_zbc_check_capacity() into sd_zbc_check_zone_size() and
renaming that function to sd_zbc_check_zones(). This removes a costly
execution of a full report zones command and so reduces device scan
duration at boot time as well as the duration of disk revalidate calls.
Furthermore, setting the partial report bit in the REPORT ZONES command
cdb can significantly reduce this command execution time as the device
does not have to count and report the total number of zones that could
be reported assuming a large enough reply buffer. A non-partial zone
report is necessary only for the first execution of report zones used to
check the same field value (to ensure that this value applies to all
zones of the disk). All other calls to sd_zbc_report_zones() can use a
partial report to reduce execution time.
Using a 14 TB ZBC disk, these simple changes reduce device scan time at
boot from about 3.5s down to about 900ms. Disk revalidate times are also
reduced from about 450ms down to 230ms.
Reviewed-by: Christoph Hellwig <[email protected]>
Reviewed-by: Hannes Reinecke <[email protected]>
Acked-by: Martin K. Petersen <[email protected]>
Signed-off-by: Damien Le Moal <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
Move the urswrz check out of sd_zbc_read_zones() and into
sd_zbc_read_zoned_characteristics() where that value is obtained (read
from the disk zoned characteristics VPD page). Since this function now
does more than simply reading the VPD page, rename it to
sd_zbc_check_zoned_characteristics().
Also fix the error message displayed when reading that VPD page fails.
Reviewed-by: Christoph Hellwig <[email protected]>
Reviewed-by: Hannes Reinecke <[email protected]>
Acked-by: Martin K. Petersen <[email protected]>
Signed-off-by: Damien Le Moal <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
tocuse is not used after setting its value. It is safe to remove
the unused variable.
Signed-off-by: zhong jiang <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
Check return values of dma_set_mask_and_coherent().
Otherwise, if dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(64));
fails, the following piece of code will be executed even when the call
to dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32)); returns 0:
dev_err(&pdev->dev, "DMA mask error %d\n", rc);
goto err_out_regions;
Addresses-Coverity-ID: 1474553 ("Unchecked return value")
Fixes: 138126214868 ("skd: switch to the generic DMA API")
Reviewed-by: Christoph Hellwig <[email protected]>
Signed-off-by: Gustavo A. R. Silva <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
If a block device is hot-added when we are out of grants,
gnttab_grant_foreign_access fails with -ENOSPC (log message "28
granting access to ring page") in this code path:
talk_to_blkback ->
setup_blkring ->
xenbus_grant_ring ->
gnttab_grant_foreign_access
and the failing path in talk_to_blkback sets the driver_data to NULL:
destroy_blkring:
blkif_free(info, 0);
mutex_lock(&blkfront_mutex);
free_info(info);
mutex_unlock(&blkfront_mutex);
dev_set_drvdata(&dev->dev, NULL);
This results in a NULL pointer BUG when blkfront_remove and blkif_free
try to access the failing device's NULL struct blkfront_info.
Cc: [email protected] # 4.5 and later
Signed-off-by: Vasilis Liaskovitis <[email protected]>
Reviewed-by: Roger Pau Monné <[email protected]>
Signed-off-by: Konrad Rzeszutek Wilk <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"There have been little changes in ALSA core stuff, but ASoC core still
kept rolling for the continued restructuring. The rest are lots of
small driver-specific changes and some minor API updates. Here are
highlights:
General:
- Appropriate fall-through annotations everywhere
- Some code cleanup in memalloc code, handling non-cacahed pages more
commonly in the helper
- Deployment of SNDRV_PCM_INFO_SYNC_APPLPTR flag consistently
Drivers:
- More HD-audio CA0132 codec improvement for supporting other Creative
boards
- Plumbing legacy HD-audio codecs as ASoC BE on Intel SST; this will
give move support of existing HD-audio devices with DSP
- A few device-specific HD-audio quirks as usual
- New quirk for RME CC devices and correction for B&W PX for USB-audio
- FireWire: code refactoring including devres usages
ASoC Core:
- Continued componentization works; it's almost done!
- A bunch of new for_each_foo macros
- Cleanups and fixes in DAPM code
ASoC Drivers:
- MCLK support for several different devices, including CS42L51, STM32
SAI, and MAX98373
- Support for Allwinner A64 CODEC analog, Intel boards with DA7219 and
MAX98927, Meson AXG PDM inputs, Nuvoton NAU8822, Renesas R8A7744 and
TI PCM3060"
* tag 'sound-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (299 commits)
ASoC: stm32: sai: fix master clock naming
ASoC: stm32: add clock dependency for sai
ALSA: hda/ca0132 - Actually fix microphone issue
ASoC: sun4i-i2s: move code from startup/shutdown hooks into pm_runtime hooks
ASoC: wm2000: Remove wm2000_read helper function
ASoC: cs42l51: fix mclk support
ASoC: wm_adsp: Log addresses as 8 digits in wm_adsp_buffer_populate
ASoC: wm_adsp: Rename memory fields in wm_adsp_buffer
ASoC: cs42l51: add mclk support
ASoC: stm32: sai: set sai as mclk clock provider
ASoC: dt-bindings: add mclk support to cs42l51
ASoC: dt-bindings: add mclk provider support to stm32 sai
ASoC: soc-core: fix trivial checkpatch issues
ASoC: dapm: Add support for hw_free on CODEC to CODEC links
ASoC: Intel: kbl_da7219_max98927: minor white space clean up
ALSA: i2c/cs8427: Fix int to char conversion
ALSA: doc: Brush up the old writing-an-alsa-driver
ASoC: rsnd: tidyup SSICR::SWSP for TDM
ASoC: rsnd: enable TDM settings for SSI parent
ASoC: pcm3168a: add hw constraint for capture channel
...
|
|
Pull SCSI updates from James Bottomley:
"This is mostly updates of the usual drivers: UFS, esp_scsi, NCR5380,
qla2xxx, lpfc, libsas, hisi_sas.
In addition there's a set of mostly small updates to the target
subsystem a set of conversions to the generic DMA API, which do have
some potential for issues in the older drivers but we'll handle those
as case by case fixes.
A new myrs driver for the DAC960/mylex raid controllers to replace the
block based DAC960 which is also being removed by Jens in this merge
window.
Plus the usual slew of trivial changes"
[ "myrs" stands for "MYlex Raid Scsi". Obviously. Silly of me to even
wonder. There's also a "myrb" driver, where the 'b' stands for
'block'. Truly, somebody has got mad naming skillz. - Linus ]
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (237 commits)
scsi: myrs: Fix the processor absent message in processor_show()
scsi: myrs: Fix a logical vs bitwise bug
scsi: hisi_sas: Fix NULL pointer dereference
scsi: myrs: fix build failure on 32 bit
scsi: fnic: replace gross legacy tag hack with blk-mq hack
scsi: mesh: switch to generic DMA API
scsi: ips: switch to generic DMA API
scsi: smartpqi: fully convert to the generic DMA API
scsi: vmw_pscsi: switch to generic DMA API
scsi: snic: switch to generic DMA API
scsi: qla4xxx: fully convert to the generic DMA API
scsi: qla2xxx: fully convert to the generic DMA API
scsi: qla1280: switch to generic DMA API
scsi: qedi: fully convert to the generic DMA API
scsi: qedf: fully convert to the generic DMA API
scsi: pm8001: switch to generic DMA API
scsi: nsp32: switch to generic DMA API
scsi: mvsas: fully convert to the generic DMA API
scsi: mvumi: switch to generic DMA API
scsi: mpt3sas: switch to generic DMA API
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- Fix ASPM link_state teardown on removal (Lukas Wunner)
- Fix misleading _OSC ASPM message (Sinan Kaya)
- Make _OSC optional for PCI (Sinan Kaya)
- Don't initialize ASPM link state when ACPI_FADT_NO_ASPM is set
(Patrick Talbert)
- Remove x86 and arm64 node-local allocation for host bridge structures
(Punit Agrawal)
- Pay attention to device-specific _PXM node values (Jonathan Cameron)
- Support new Immediate Readiness bit (Felipe Balbi)
- Differentiate between pciehp surprise and safe removal (Lukas Wunner)
- Remove unnecessary pciehp includes (Lukas Wunner)
- Drop pciehp hotplug_slot_ops wrappers (Lukas Wunner)
- Tolerate PCIe Slot Presence Detect being hardwired to zero to
workaround broken hardware, e.g., the Wilocity switch/wireless device
(Lukas Wunner)
- Unify pciehp controller & slot structs (Lukas Wunner)
- Constify hotplug_slot_ops (Lukas Wunner)
- Drop hotplug_slot_info (Lukas Wunner)
- Embed hotplug_slot struct into users instead of allocating it
separately (Lukas Wunner)
- Initialize PCIe port service drivers directly instead of relying on
initcall ordering (Keith Busch)
- Restore PCI config state after a slot reset (Keith Busch)
- Save/restore DPC config state along with other PCI config state
(Keith Busch)
- Reference count devices during AER handling to avoid race issue with
concurrent hot removal (Keith Busch)
- If an Upstream Port reports ERR_FATAL, don't try to read the Port's
config space because it is probably unreachable (Keith Busch)
- During error handling, use slot-specific reset instead of secondary
bus reset to avoid link up/down issues on hotplug ports (Keith Busch)
- Restore previous AER/DPC handling that does not remove and
re-enumerate devices on ERR_FATAL (Keith Busch)
- Notify all drivers that may be affected by error recovery resets
(Keith Busch)
- Always generate error recovery uevents, even if a driver doesn't have
error callbacks (Keith Busch)
- Make PCIe link active reporting detection generic (Keith Busch)
- Support D3cold in PCIe hierarchies during system sleep and runtime,
including hotplug and Thunderbolt ports (Mika Westerberg)
- Handle hpmemsize/hpiosize kernel parameters uniformly, whether slots
are empty or occupied (Jon Derrick)
- Remove duplicated include from pci/pcie/err.c and unused variable
from cpqphp (YueHaibing)
- Remove driver pci_cleanup_aer_uncorrect_error_status() calls (Oza
Pawandeep)
- Uninline PCI bus accessors for better ftracing (Keith Busch)
- Remove unused AER Root Port .error_resume method (Keith Busch)
- Use kfifo in AER instead of a local version (Keith Busch)
- Use threaded IRQ in AER bottom half (Keith Busch)
- Use managed resources in AER core (Keith Busch)
- Reuse pcie_port_find_device() for AER injection (Keith Busch)
- Abstract AER interrupt handling to disconnect error injection (Keith
Busch)
- Refactor AER injection callbacks to simplify future improvments
(Keith Busch)
- Remove unused Netronome NFP32xx Device IDs (Jakub Kicinski)
- Use bitmap_zalloc() for dma_alias_mask (Andy Shevchenko)
- Add switch fall-through annotations (Gustavo A. R. Silva)
- Remove unused Switchtec quirk variable (Joshua Abraham)
- Fix pci.c kernel-doc warning (Randy Dunlap)
- Remove trivial PCI wrappers for DMA APIs (Christoph Hellwig)
- Add Intel GPU device IDs to spurious interrupt quirk (Bin Meng)
- Run Switchtec DMA aliasing quirk only on NTB endpoints to avoid
useless dmesg errors (Logan Gunthorpe)
- Update Switchtec NTB documentation (Wesley Yung)
- Remove redundant "default n" from Kconfig (Bartlomiej Zolnierkiewicz)
- Avoid panic when drivers enable MSI/MSI-X twice (Tonghao Zhang)
- Add PCI support for peer-to-peer DMA (Logan Gunthorpe)
- Add sysfs group for PCI peer-to-peer memory statistics (Logan
Gunthorpe)
- Add PCI peer-to-peer DMA scatterlist mapping interface (Logan
Gunthorpe)
- Add PCI configfs/sysfs helpers for use by peer-to-peer users (Logan
Gunthorpe)
- Add PCI peer-to-peer DMA driver writer's documentation (Logan
Gunthorpe)
- Add block layer flag to indicate driver support for PCI peer-to-peer
DMA (Logan Gunthorpe)
- Map Infiniband scatterlists for peer-to-peer DMA if they contain P2P
memory (Logan Gunthorpe)
- Register nvme-pci CMB buffer as PCI peer-to-peer memory (Logan
Gunthorpe)
- Add nvme-pci support for PCI peer-to-peer memory in requests (Logan
Gunthorpe)
- Use PCI peer-to-peer memory in nvme (Stephen Bates, Steve Wise,
Christoph Hellwig, Logan Gunthorpe)
- Cache VF config space size to optimize enumeration of many VFs
(KarimAllah Ahmed)
- Remove unnecessary <linux/pci-ats.h> include (Bjorn Helgaas)
- Fix VMD AERSID quirk Device ID matching (Jon Derrick)
- Fix Cadence PHY handling during probe (Alan Douglas)
- Signal Cadence Endpoint interrupts via AXI region 0 instead of last
region (Alan Douglas)
- Write Cadence Endpoint MSI interrupts with 32 bits of data (Alan
Douglas)
- Remove redundant controller tests for "device_type == pci" (Rob
Herring)
- Document R-Car E3 (R8A77990) bindings (Tho Vu)
- Add device tree support for R-Car r8a7744 (Biju Das)
- Drop unused mvebu PCIe capability code (Thomas Petazzoni)
- Add shared PCI bridge emulation code (Thomas Petazzoni)
- Convert mvebu to use shared PCI bridge emulation (Thomas Petazzoni)
- Add aardvark Root Port emulation (Thomas Petazzoni)
- Support 100MHz/200MHz refclocks for i.MX6 (Lucas Stach)
- Add initial power management for i.MX7 (Leonard Crestez)
- Add PME_Turn_Off support for i.MX7 (Leonard Crestez)
- Fix qcom runtime power management error handling (Bjorn Andersson)
- Update TI dra7xx unaligned access errata workaround for host mode as
well as endpoint mode (Vignesh R)
- Fix kirin section mismatch warning (Nathan Chancellor)
- Remove iproc PAXC slot check to allow VF support (Jitendra Bhivare)
- Quirk Keystone K2G to limit MRRS to 256 (Kishon Vijay Abraham I)
- Update Keystone to use MRRS quirk for host bridge instead of open
coding (Kishon Vijay Abraham I)
- Refactor Keystone link establishment (Kishon Vijay Abraham I)
- Simplify and speed up Keystone link training (Kishon Vijay Abraham I)
- Remove unused Keystone host_init argument (Kishon Vijay Abraham I)
- Merge Keystone driver files into one (Kishon Vijay Abraham I)
- Remove redundant Keystone platform_set_drvdata() (Kishon Vijay
Abraham I)
- Rename Keystone functions for uniformity (Kishon Vijay Abraham I)
- Add Keystone device control module DT binding (Kishon Vijay Abraham
I)
- Use SYSCON API to get Keystone control module device IDs (Kishon
Vijay Abraham I)
- Clean up Keystone PHY handling (Kishon Vijay Abraham I)
- Use runtime PM APIs to enable Keystone clock (Kishon Vijay Abraham I)
- Clean up Keystone config space access checks (Kishon Vijay Abraham I)
- Get Keystone outbound window count from DT (Kishon Vijay Abraham I)
- Clean up Keystone outbound window configuration (Kishon Vijay Abraham
I)
- Clean up Keystone DBI setup (Kishon Vijay Abraham I)
- Clean up Keystone ks_pcie_link_up() (Kishon Vijay Abraham I)
- Fix Keystone IRQ status checking (Kishon Vijay Abraham I)
- Add debug messages for all Keystone errors (Kishon Vijay Abraham I)
- Clean up Keystone includes and macros (Kishon Vijay Abraham I)
- Fix Mediatek unchecked return value from devm_pci_remap_iospace()
(Gustavo A. R. Silva)
- Fix Mediatek endpoint/port matching logic (Honghui Zhang)
- Change Mediatek Root Port Class Code to PCI_CLASS_BRIDGE_PCI (Honghui
Zhang)
- Remove redundant Mediatek PM domain check (Honghui Zhang)
- Convert Mediatek to pci_host_probe() (Honghui Zhang)
- Fix Mediatek MSI enablement (Honghui Zhang)
- Add Mediatek system PM support for MT2712 and MT7622 (Honghui Zhang)
- Add Mediatek loadable module support (Honghui Zhang)
- Detach VMD resources after stopping root bus to prevent orphan
resources (Jon Derrick)
- Convert pcitest build process to that used by other tools (iio, perf,
etc) (Gustavo Pimentel)
* tag 'pci-v4.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (140 commits)
PCI/AER: Refactor error injection fallbacks
PCI/AER: Abstract AER interrupt handling
PCI/AER: Reuse existing pcie_port_find_device() interface
PCI/AER: Use managed resource allocations
PCI: pcie: Remove redundant 'default n' from Kconfig
PCI: aardvark: Implement emulated root PCI bridge config space
PCI: mvebu: Convert to PCI emulated bridge config space
PCI: mvebu: Drop unused PCI express capability code
PCI: Introduce PCI bridge emulated config space common logic
PCI: vmd: Detach resources after stopping root bus
nvmet: Optionally use PCI P2P memory
nvmet: Introduce helper functions to allocate and free request SGLs
nvme-pci: Add support for P2P memory in requests
nvme-pci: Use PCI p2pmem subsystem to manage the CMB
IB/core: Ensure we map P2P memory correctly in rdma_rw_ctx_[init|destroy]()
block: Add PCI P2P flag for request queue
PCI/P2PDMA: Add P2P DMA driver writer's documentation
docs-rst: Add a new directory for PCI documentation
PCI/P2PDMA: Introduce configfs/sysfs enable attribute helpers
PCI/P2PDMA: Add PCI p2pmem DMA mappings to adjust the bus offset
...
|
|
Pull dmaengine updates from Vinod Koul:
- Support for ColdFire mcf5441x edma controller
- Support for link list mode in sprd dma
- More users of managed dmaenginem_async_device_register API
- Cyclic mode support in owl dma driver
- DT updates for renesas drivers, dma-jz4780 updates and support for
JZ4770, JZ4740 and JZ4725B controllers
- Removal of deprecated dma_slave_config direction in dmaengine
drivers, few more users will be removed in next cycle and eventually
removed.
- Minor updates to idma64, ioat, pxa, ppc drivers
* tag 'dmaengine-4.20-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (66 commits)
dmaengine: ppc4xx: fix off-by-one build failure
dmaengine: owl: Fix warnings generated during build
dmaengine: fsl-edma: remove dma_slave_config direction usage
dmaengine: rcar-dmac: set scatter/gather max segment size
dmaengine: mmp_tdma: remove dma_slave_config direction usage
dmaengine: ep93xx_dma: remove dma_slave_config direction usage
dmaengine: k3dma: remove dma_slave_config direction usage
dmaengine: k3dma: dont use direction for memcpy
dmaengine: imx-dma: remove dma_slave_config direction usage
dmaengine: idma: remove dma_slave_config direction usage
dmaengine: hsu: remove dma_slave_config direction usage
dmaengine: dw: remove dma_slave_config direction usage
dmaengine: jz4740: remove dma_slave_config direction usage
dmaengine: coh901318: remove dma_slave_config direction usage
dmaengine: bcm2835: remove dma_slave_config direction usage
dmaengine: at_hdmac: remove dma_slave_config direction usage
dmaengine: owl: Add Slave and Cyclic mode support for Actions Semi Owl S900 SoC
dmaengine: ioat: fix prototype of ioat_enumerate_channels
dmaengine: stm32-dma: check whether length is aligned on FIFO threshold
dt-bindings: dmaengine: usb-dmac: Add binding for r8a7744
...
|
|
Pull EDAC updates from Borislav Petkov:
"The EDAC tree was busier than usual this cycle as the shortlog below
shows.
Also, this pull request is carrying an ACPI DSM driver which is used
to ask the platform to supply the DIMM location of a reported hardware
error and thus simplify all the EDAC logic when trying to map the
error address to the respective DIMM.
Core EDAC updates:
- amd64_edac: AMD family 0x17, models 0x10-0x2f support (Michael Jin)
Hygon Dhyana support (Pu Wen)
- sb_edac: New maintainer + fixes (Tony Luck) Error reporting
improvements and fixes (Qiuxu Zhuo)
- ghes_edac: SMBIOS handle type 17 for DIMM locating and per-DIMM
error accounting (Fan Wu)
- altera_edac: Stratix10 support and refactoring (Thor Thayer)
Out of tree addition:
- acpi_adxl: Address Translation interface using an ACPI DSM (Tony
Luck)
- the usual amount of other misc fixes and cleanups all over"
* tag 'edac_for_4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp: (22 commits)
ACPI/ADXL: Add address translation interface using an ACPI DSM
EDAC, thunderx: Fix memory leak in thunderx_l2c_threaded_isr()
EDAC, skx_edac: Fix logical channel intermediate decoding
EDAC, {i7core,sb,skx}_edac: Fix uncorrected error counting
EDAC, altera: Work around int-to-pointer-cast warnings
EDAC, amd64: Add Hygon Dhyana support
EDAC: Raise the maximum number of memory controllers
arm64: dts: stratix10: Add peripheral EDAC nodes
EDAC, altera: Add Stratix10 peripheral support
EDAC, altera: Merge Stratix10 into the Arria10 SDRAM probe routine
arm64: dts: stratix10: Add SDRAM node
EDAC, altera: Combine Stratix10 and Arria10 probe functions
arm64: dts: stratix10: Additions to EDAC System Manager
EDAC, i7core: Remove set but not used variable pvt
EDAC, ghes: Use CPER module handles to locate DIMMs
EDAC: Correct DIMM capacity unit symbol
EDAC, sb_edac: Fix signedness bugs in *_get_ha() functions
EDAC, sb_edac: Fix reporting for patrol scrubber errors
EDAC, sb_edac: Return early on ADDRV bit and address type test
MAINTAINERS: Update maintainer for drivers/edac/sb_edac.c
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
- Improve the efficiency and performance of reading nvdimm-namespace
labels. Reduce the amount of label data read at driver load time by a
few orders of magnitude. Reduce heavyweight call-outs to
platform-firmware routines.
- Handle media errors located in the 'struct page' array stored on a
persistent memory namespace. Let the kernel clear these errors rather
than an awkward userspace workaround.
- Fix Address Range Scrub (ARS) completion tracking. Correct occasions
where the kernel indicates completion of ARS before submission.
- Fix asynchronous device registration reference counting.
- Add support for reporting an nvdimm dirty-shutdown-count via sysfs.
- Fix various small libnvdimm core and uapi issues.
* tag 'libnvdimm-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (21 commits)
acpi, nfit: Further restrict userspace ARS start requests
acpi, nfit: Fix Address Range Scrub completion tracking
UAPI: ndctl: Remove use of PAGE_SIZE
UAPI: ndctl: Fix g++-unsupported initialisation in headers
tools/testing/nvdimm: Populate dirty shutdown data
acpi, nfit: Collect shutdown status
acpi, nfit: Introduce nfit_mem flags
libnvdimm, label: Fix sparse warning
nvdimm: Use namespace index data to reduce number of label reads needed
nvdimm: Split label init out from the logic for getting config data
nvdimm: Remove empty if statement
nvdimm: Clarify comment in sizeof_namespace_index
nvdimm: Sanity check labeloff
libnvdimm, dimm: Maximize label transfer size
libnvdimm, pmem: Fix badblocks population for 'raw' namespaces
libnvdimm, namespace: Drop the repeat assignment for variable dev->parent
libnvdimm, region: Fail badblocks listing for inactive regions
libnvdimm, pfn: during init, clear errors in the metadata area
libnvdimm: Set device node in nd_device_register
libnvdimm: Hold reference on parent while scheduling async init
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
- Add Spreadtrum SC2731 charger driver
- bq25890-charger: Add BQ25896 support
- bq27xxx-battery: Add support for BQ27411
- qcom-pon: Add pms405 pon support
- cros-charger: add support for dedicated port
- misc fixes
* tag 'for-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (28 commits)
power: max8925: mark expected switch fall-through
power: supply: fix spelling mistake "Gauage" -> "Gauge"
power: reset: qcom-pon: Add pms405 pon support
power: supply: bq27xxx: Add support for BQ27411
power: supply: Add Spreadtrum SC2731 charger support
dt-bindings: power: Add Spreadtrum SC2731 charger documentation
power: supply: twl4030_charger: disable eoc interrupt on linear charge
power: supply: twl4030_charger: fix charging current out-of-bounds
power: supply: bq25890_charger: fix semicolon.cocci warnings
power: supply: max8998-charger: Fix platform data retrieval
power: supply: cros: add support for dedicated port
mfd: cros: add charger port count command definition
power: reset: at91-poweroff: do not procede if at91_shdwc is allocated
power: reset: at91-poweroff: rename at91_shdwc_base member of struct shdwc
power: reset: at91-poweroff: make sclk part of struct shdwc
power: reset: at91-poweroff: make mpddrc_base part of struct shdwc
power: reset: at91-poweroff: use only one poweroff function
power: reset: at91-poweroff: switch to slow clock before shutdown
power: reset: convert to SPDX identifiers
power: supply: ab8500_fg: silence uninitialized variable warnings
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID updates from Jiri Kosina:
- rumble support for Xbox One S, from Andrey Smirnov
- high-resolution support for Logitech mice, from Harry Cutts
- support for recent devices requiring the HID parse to be able to cope
with tag report sizes > 256
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (35 commits)
HID: usbhid: Add quirk for Redragon/Dragonrise Seymur 2
HID: wacom: Work around HID descriptor bug in DTK-2451 and DTH-2452
HID: google: add dependency on Cros EC for Hammer
HID: elan: fix spelling mistake "registred" -> "registered"
HID: google: drop superfluous const before SIMPLE_DEV_PM_OPS()
HID: google: add support tablet mode switch for Whiskers
mfd: cros: add "base attached" MKBP switch definition
Input: reserve 2 events code because of HID
HID: magicmouse: add support for Apple Magic Trackpad 2
HID: i2c-hid: override HID descriptors for certain devices
HID: hid-bigbenff: driver for BigBen Interactive PS3OFMINIPAD gamepad
HID: logitech: fix a used uninitialized GCC warning
HID: intel-ish-hid: using list_head for ipc write queue
HID: intel-ish-hid: use resource-managed api
HID: intel_ish-hid: Enhance API to get ring buffer sizes
HID: intel-ish-hid: use helper function to search client id
HID: intel-ish-hid: ishtp: add helper function for client search
HID: intel-ish-hid: use helper function to access client buffer
HID: intel-ish-hid: ishtp: add helper functions for client buffer operation
HID: intel-ish-hid: use helper function for private driver data set/get
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight
Pull backlight updates from Lee Jones:
"Old Drivers
- Remove driver for S6E63M0
- Remove driver for LD9040
Fix-ups
- Trivial (email address update); adp*_bl
- Use 'atomic' PWM API; pwm_bl
Bug Fixes
- Remove pointless boolen '&ptr' check; lm3639_bl"
* tag 'backlight-next-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
backlight: Remove ld9040 driver
backlight: Remove s6e63m0 driver
backlight: lm3639: Unconditionally call led_classdev_unregister
backlight: pwm_bl: Switch to using "atomic" PWM API
backlight: Update MODULE AUTHOR email address
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers
- Add support for USART SPI to AT91*
New Functionality
- Add support for Audio CODECs to motorola-cpcap
Fix-ups
- DT documentation fix-ups; atmel-usart
- Staticise functions/structs; spi-at91-usart, arizona-core
- Constify; ti-lmu
- Fix memory leaks; menelaus
- Change device 'wake-up' status; ti_am335x_tscadc, max8997
- Power Management (suspend/resume) semantic changes; ti_am335x_adc, cros_ec, max8997
- SPDX churn; sec-core (+ headers), max* (+ headers), intel* (+ headers),
- Trivial (whitespace, email addresses, alphabetisise); Kconfig, adp5520, intel_soc_pmic_*
- Build as module; sec-irq
- Use new %pOFn printk format for device_node.name; max77620
- Remove unused code; madera
- Use generic MACROs; intel_msic, intel_soc_pmic_crc
- Move to GPIOD; ti-lmu
- Use managed resources; ti-lmu
Bug Fixes
- Add missing headers; at91-usart
- Prevent device from entering low-power mode; arizona-core
- Poll for BOOT_DONE to avoid still-booting NACK; madera-core
- Prevent ADC read from shutting down device; mc13xxx-core"
* tag 'mfd-next-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (45 commits)
mfd: cros_ec: Avoid unneeded internal declaration warning
mfd: ti-lmu: Use of_device_get_match_data() helper
mfd: ti-lmu: Use managed resource for everything
mfd: ti-lmu: Switch to GPIOD
mfd: ti-lmu: constify mfd_cell tables
mfd: max8997: Disable interrupt handling for suspend/resume cycle
mfd: max8997: Enale irq-wakeup unconditionally
mfd: arizona: Make array mclk_name static, shrinks object size
MAINTAINERS: Add myself as designated reviewer of Intel MFD PMIC
mfd: Convert Intel PMIC drivers to use SPDX identifier 1;5201;0c Reduce size of duplicated comments by switching to use SPDX identifier.
mfd: Sort headers alphabetically for Intel PMIC drivers
mfd: intel_soc_pmic_bxtwc: Chain power button IRQs as well
mfd: intel_soc_pmic_crc: Use REGMAP_IRQ_REG() macro
mfd: intel_soc_pmic_crc: Use DEFINE_RES_IRQ_NAMED() macro
mfd: intel_msic: Use DEFINE_RES_IRQ() macro
mfd: motorola-cpcap: Add audio-codec support
mfd: mc13xxx-core: Fix PMIC shutdown when reading ADC values
mfd: madera: Remove unused forward reference
mfd: max77620: Convert to using %pOFn instead of device_node.name
mfd: madera: Don't use regmap_read_poll_timeout to poll for BOOT_DONE
...
|
|
MOVDIR64B moves 64-bytes as direct-store with 64-bytes write atomicity.
Direct store is implemented by using write combining (WC) for writing
data directly into memory without caching the data.
In low latency offload (e.g. Non-Volatile Memory, etc), MOVDIR64B writes
work descriptors (and data in some cases) to device-hosted work-queues
atomically without cache pollution.
Availability of the MOVDIR64B instruction is indicated by the
presence of the CPUID feature flag MOVDIR64B (CPUID.0x07.0x0:ECX[bit 28]).
Please check the latest Intel Architecture Instruction Set Extensions
and Future Features Programming Reference for more details on the CPUID
feature MOVDIR64B flag.
Signed-off-by: Fenghua Yu <[email protected]>
Cc: Andy Lutomirski <[email protected]>
Cc: Ashok Raj <[email protected]>
Cc: Borislav Petkov <[email protected]>
Cc: Brian Gerst <[email protected]>
Cc: Denys Vlasenko <[email protected]>
Cc: H. Peter Anvin <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Ravi V Shankar <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Ingo Molnar <[email protected]>
|
|
MOVDIRI moves doubleword or quadword from register to memory through
direct store which is implemented by using write combining (WC) for
writing data directly into memory without caching the data.
Programmable agents can handle streaming offload (e.g. high speed packet
processing in network). Hardware implements a doorbell (tail pointer)
register that is updated by software when adding new work-elements to
the streaming offload work-queue.
MOVDIRI can be used as the doorbell write which is a 4-byte or 8-byte
uncachable write to MMIO. MOVDIRI has lower overhead than other ways
to write the doorbell.
Availability of the MOVDIRI instruction is indicated by the presence of
the CPUID feature flag MOVDIRI(CPUID.0x07.0x0:ECX[bit 27]).
Please check the latest Intel Architecture Instruction Set Extensions
and Future Features Programming Reference for more details on the CPUID
feature MOVDIRI flag.
Signed-off-by: Fenghua Yu <[email protected]>
Cc: Andy Lutomirski <[email protected]>
Cc: Ashok Raj <[email protected]>
Cc: Borislav Petkov <[email protected]>
Cc: Brian Gerst <[email protected]>
Cc: Denys Vlasenko <[email protected]>
Cc: H. Peter Anvin <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Ravi V Shankar <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Ingo Molnar <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Fixes 2018-10-24
This series contains fixes for the ice driver.
Anirudh fixes a namespace issue which was introduced with a previous
patch to remove ice_netpoll. Fixed up the device ID define names to
align with the branding string names. Use the capability count returned
by the firmware, instead of calculating the count. Introduced driver
workarounds due to current firmware limitations. Fixed the queue
mapping for a VF, which needs to be set in the config and scatter queue
modes. Fixed the driver which is setup to handle link status events
(LSE), even though the firmware does not have this feature yet, so add
the ability to poll for link status changes while we wait for updated
firmware.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
route
The intent of ip6_route_check_nh_onlink is to make sure the gateway
given for an onlink route is not actually on a connected route for
a different interface (e.g., 2001:db8:1::/64 is on dev eth1 and then
an onlink route has a via 2001:db8:1::1 dev eth2). If the gateway
lookup hits the default route then it most likely will be a different
interface than the onlink route which is ok.
Update ip6_route_check_nh_onlink to disregard the device mismatch
if the gateway lookup hits the default route. Turns out the existing
onlink tests are passing because there is no default route or it is
an unreachable default, so update the onlink tests to have a default
route other than unreachable.
Fixes: fc1e64e1092f6 ("net/ipv6: Add support for onlink flag")
Signed-off-by: David Ahern <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Marco reported an error with hfsc:
root@Calimero:~# tc qdisc add dev eth0 root handle 1:0 hfsc default 1
Error: Attribute failed policy validation.
Apparently a few implementations pass TCA_OPTIONS as a binary instead
of nested attribute, so drop TCA_OPTIONS from the policy.
Fixes: 8b4c3cdd9dd8 ("net: sched: Add policy validation for tc attributes")
Reported-by: Marco Berizzi <[email protected]>
Signed-off-by: David Ahern <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
When the physical link goes up or down, the driver is supposed to
receive a link status event (LSE). The driver currently has the code
to handle LSEs but there is no firmware support for this feature yet.
So this patch adds the ability for the driver to poll for link status
changes. The polling itself is done in ice_watchdog_subtask.
For namespace cleanliness, this patch also removes code that handles
LSE. This code will be reintroduced once the feature is officially
supported.
Signed-off-by: Anirudh Venkataramanan <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
Allocate VF interrupts using VPINT_ALLOC_PCI. Multiple interrupts are
specified as a range from "first" to "last".
Also, according to the spec, the queue mapping for a VF needs to be set
in both contig and scatter queue modes. So make this change as well.
Signed-off-by: Anirudh Venkataramanan <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
ice_dev_onetime_setup contains a couple of driver workarounds for current
firmware limitations. These workarounds are expected to go away once
these limitations are fixed in the firmware.
On a firmware release that has these issues addressed, these workarounds
(while unnecessary) will not break anything.
Signed-off-by: Anirudh Venkataramanan <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
This patch fixes the smatch warning,
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_err.c:700
hclge_log_and_clear_ppp_error() error: uninitialized symbol
'hw_err_lst3'
Link: https://lkml.org/lkml/2018/10/23/430
Fixes: da2d072a9ea7 ("net: hns3: Add enable and process hw errors from PPP")
Reported-by: Dan Carpenter <[email protected]>
Signed-off-by: Shiju Jose <[email protected]>
Signed-off-by: Salil Mehta <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This is a copy and paste bug where we copied the sizeof() from the chunk
before. We're copying more data than intended but the destination is a
union so it doesn't cause memory corruption.
Fixes: ffb0abd7e9cb ("octeontx2-af: NIX AQ instruction enqueue support")
Signed-off-by: Dan Carpenter <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Current handling of CHECKSUM_COMPLETE packets by the UDP stack is
incorrect for any packet that has an incorrect checksum value.
udp4/6_csum_init() will both make a call to
__skb_checksum_validate_complete() to initialize/validate the csum
field when receiving a CHECKSUM_COMPLETE packet. When this packet
fails validation, skb->csum will be overwritten with the pseudoheader
checksum so the packet can be fully validated by software, but the
skb->ip_summed value will be left as CHECKSUM_COMPLETE so that way
the stack can later warn the user about their hardware spewing bad
checksums. Unfortunately, leaving the SKB in this state can cause
problems later on in the checksum calculation.
Since the the packet is still marked as CHECKSUM_COMPLETE,
udp_csum_pull_header() will SUBTRACT the checksum of the UDP header
from skb->csum instead of adding it, leaving us with a garbage value
in that field. Once we try to copy the packet to userspace in the
udp4/6_recvmsg(), we'll make a call to skb_copy_and_csum_datagram_msg()
to checksum the packet data and add it in the garbage skb->csum value
to perform our final validation check.
Since the value we're validating is not the proper checksum, it's possible
that the folded value could come out to 0, causing us not to drop the
packet. Instead, we believe that the packet was checksummed incorrectly
by hardware since skb->ip_summed is still CHECKSUM_COMPLETE, and we attempt
to warn the user with netdev_rx_csum_fault(skb->dev);
Unfortunately, since this is the UDP path, skb->dev has been overwritten
by skb->dev_scratch and is no longer a valid pointer, so we end up
reading invalid memory.
This patch addresses this problem in two ways:
1) Do not use the dev pointer when calling netdev_rx_csum_fault()
from skb_copy_and_csum_datagram_msg(). Since this gets called
from the UDP path where skb->dev has been overwritten, we have
no way of knowing if the pointer is still valid. Also for the
sake of consistency with the other uses of
netdev_rx_csum_fault(), don't attempt to call it if the
packet was checksummed by software.
2) Add better CHECKSUM_COMPLETE handling to udp4/6_csum_init().
If we receive a packet that's CHECKSUM_COMPLETE that fails
verification (i.e. skb->csum_valid == 0), check who performed
the calculation. It's possible that the checksum was done in
software by the network stack earlier (such as Netfilter's
CONNTRACK module), and if that says the checksum is bad,
we can drop the packet immediately instead of waiting until
we try and copy it to userspace. Otherwise, we need to
mark the SKB as CHECKSUM_NONE, since the skb->csum field
no longer contains the full packet checksum after the
call to __skb_checksum_validate_complete().
Fixes: e6afc8ace6dd ("udp: remove headers from UDP packets before queueing")
Fixes: c84d949057ca ("udp: copy skb->truesize in the first cache line")
Cc: Sam Kumar <[email protected]>
Cc: Eric Dumazet <[email protected]>
Signed-off-by: Sean Tranchetti <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
David Ahern says:
====================
net: Fixups for recent dump filtering changes
Li RongQing noted that tgt_net is leaked in ipv4 due to the recent change
to handle address dumps for a specific device. The report also applies to
ipv6 and other error paths. Patches 1 and 2 fix those leaks.
Patch 3 stops route dumps from erroring out when dumping across address
families and a table id is given. This is needed in preparation for
patch 4.
Patch 4 updates the rtnl_dump_all to handle a failure in one of the dumpit
functions. At the moment, if an address dump returns an error the dump all
loop breaks but the error is dropped. The result can be no data is returned
and no error either leaving the user wondering about the addresses.
Patches were tested with a modified iproute2 to add invalid data to the
dump request causing each specific failure path to be hit in addition
to positive testing that it works as it should when given valid data.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
If an address, route or netconf dump request is sent for AF_UNSPEC, then
rtnl_dump_all is used to do the dump across all address families. If one
of the dumpit functions fails (e.g., invalid attributes in the dump
request) then rtnl_dump_all needs to propagate that error so the user
gets an appropriate response instead of just getting no data.
Fixes: effe67926624 ("net: Enable kernel side filtering of route dumps")
Fixes: 5fcd266a9f64 ("net/ipv4: Add support for dumping addresses for a specific device")
Fixes: 6371a71f3a3b ("net/ipv6: Add support for dumping addresses for a specific device")
Signed-off-by: David Ahern <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
When doing a route dump across all address families, do not error out
if the table does not exist. This allows a route dump for AF_UNSPEC
with a table id that may only exist for some of the families.
Do return the table does not exist error if dumping routes for a
specific family and the table does not exist.
Signed-off-by: David Ahern <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
If tgt_net is set based on IFA_TARGET_NETNSID attribute in the dump
request, make sure all error paths call put_net.
Fixes: 6371a71f3a3b ("net/ipv6: Add support for dumping addresses for a specific device")
Fixes: ed6eff11790a ("net/ipv6: Update inet6_dump_addr for strict data checking")
Signed-off-by: David Ahern <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
If tgt_net is set based on IFA_TARGET_NETNSID attribute in the dump
request, make sure all error paths call put_net.
Fixes: 5fcd266a9f64 ("net/ipv4: Add support for dumping addresses for a specific device")
Fixes: c33078e3dfb1 ("net/ipv4: Update inet_dump_ifaddr for strict data checking")
Reported-by: Li RongQing <[email protected]>
Signed-off-by: David Ahern <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The firmware now returns the capability count in the command buffer.
Use it.
Signed-off-by: Anirudh Venkataramanan <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
Update to the current firmware major and minor version which are
1 and 3 respectively.
Also remove an empty comment line.
Signed-off-by: Anirudh Venkataramanan <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
Basically remove references to C810 and use E810C (from the branding
string) instead.
Signed-off-by: Anirudh Venkataramanan <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
commit 158a08a694c4e ("ice: remove ndo_poll_controller") removed
ice_netpoll and introduced a namespace warning for ice_msix_clean_rings.
Fix the namespace warning by making ice_msix_clean_rings static.
Signed-off-by: Anirudh Venkataramanan <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
Pull documentation updates from Jonathan Corbet:
"This is a fairly typical cycle for documentation. There's some welcome
readability improvements for the formatted output, some LICENSES
updates including the addition of the ISC license, the removal of the
unloved and unmaintained 00-INDEX files, the deprecated APIs document
from Kees, more MM docs from Mike Rapoport, and the usual pile of typo
fixes and corrections"
* tag 'docs-4.20' of git://git.lwn.net/linux: (41 commits)
docs: Fix typos in histogram.rst
docs: Introduce deprecated APIs list
kernel-doc: fix declaration type determination
doc: fix a typo in adding-syscalls.rst
docs/admin-guide: memory-hotplug: remove table of contents
doc: printk-formats: Remove bogus kobject references for device nodes
Documentation: preempt-locking: Use better example
dm flakey: Document "error_writes" feature
docs/completion.txt: Fix a couple of punctuation nits
LICENSES: Add ISC license text
LICENSES: Add note to CDDL-1.0 license that it should not be used
docs/core-api: memory-hotplug: add some details about locking internals
docs/core-api: rename memory-hotplug-notifier to memory-hotplug
docs: improve readability for people with poorer eyesight
yama: clarify ptrace_scope=2 in Yama documentation
docs/vm: split memory hotplug notifier description to Documentation/core-api
docs: move memory hotplug description into admin-guide/mm
doc: Fix acronym "FEKEK" in ecryptfs
docs: fix some broken documentation references
iommu: Fix passthrough option documentation
...
|