| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
On archs like S390 or um this driver cannot build nor work.
Make it depend on HAS_IOMEM to bypass build failures.
drivers/built-in.o: In function `dw_wdt_drv_probe':
drivers/watchdog/dw_wdt.c:302: undefined reference to `devm_ioremap_resource'
Signed-off-by: Richard Weinberger <[email protected]>
Signed-off-by: Wim Van Sebroeck <[email protected]>
|
|
In the event that a send fails in an uncached write, or we end up
needing to reissue it (-EAGAIN case), we'll kfree the wdata but
the pages currently leak.
Fix this by adding a new kref release routine for uncached writedata
that releases the pages, and have the uncached codepaths use that.
[original patch by Jeff modified to fix minor formatting problems]
Signed-off-by: Jeff Layton <[email protected]>
Reviewed-by: Pavel Shilovsky <[email protected]>
Signed-off-by: Steve French <[email protected]>
|
|
The cifs_writedata code uses a single element trailing array, which
just adds unneeded complexity. Use a flexarray instead.
Signed-off-by: Jeff Layton <[email protected]>
Reviewed-by: Pavel Shilovsky <[email protected]>
Signed-off-by: Steve French <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fix from Greg KH:
"Here is a single kernfs fix to resolve a much-reported lockdep issue
with the removal of entries in sysfs"
* tag 'driver-core-3.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
kernfs: make kernfs_deactivate() honor KERNFS_LOCKDEP flag
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull ceph fixes from Sage Weil:
"There is an RBD fix for a crash due to the immutable bio changes, an
error path fix, and a locking fix in the recent redirect support"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
libceph: do not dereference a NULL bio pointer
libceph: take map_sem for read in handle_reply()
libceph: factor out logic from ceph_osdc_start_request()
libceph: fix error handling in ceph_osdc_init()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Relax VDSO alignment requirements so that the kernel-picked one (4K)
does not conflict with the dynamic linker's one (64K)
- VDSO gettimeofday fix
- Barrier fixes for atomic operations and cache flushing
- TLB invalidation when overriding early page mappings during boot
- Wired up new 32-bit arm (compat) syscalls
- LSM_MMAP_MIN_ADDR when COMPAT is enabled
- defconfig update
- Clean-up (comments, pgd_alloc).
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: defconfig: Expand default enabled features
arm64: asm: remove redundant "cc" clobbers
arm64: atomics: fix use of acquire + release for full barrier semantics
arm64: barriers: allow dsb macro to take option parameter
security: select correct default LSM_MMAP_MIN_ADDR on arm on arm64
arm64: compat: Wire up new AArch32 syscalls
arm64: vdso: update wtm fields for CLOCK_MONOTONIC_COARSE
arm64: vdso: fix coarse clock handling
arm64: simplify pgd_alloc
arm64: fix typo: s/SERRROR/SERROR/
arm64: Invalidate the TLB when replacing pmd entries during boot
arm64: Align CMA sizes to PAGE_SIZE
arm64: add DSB after icache flush in __flush_icache_all()
arm64: vdso: prevent ld from aligning PT_LOAD segments to 64k
|
|
Pull MIPS updates from Ralf Baechle:
"hree minor patches. All have sat in -next for a few days"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: fpu.h: Fix build when CONFIG_BUG is not set
MIPS: Wire up sched_setattr/sched_getattr syscalls
MIPS: Alchemy: Fix DB1100 GPIO registration
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"A series of small fixes. Mostly driver ones. There is one core
regression fix on a patch that was meant to fix some race issues on
vb2, but that actually caused more harm than good. So, we're just
reverting it for now"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] adv7842: Composite free-run platfrom-data fix
[media] v4l2-dv-timings: fix GTF calculation
[media] hdpvr: Fix memory leak in debug
[media] af9035: add ID [2040:f900] Hauppauge WinTV-MiniStick 2
[media] mxl111sf: Fix compile when CONFIG_DVB_USB_MXL111SF is unset
[media] mxl111sf: Fix unintentional garbage stack read
[media] cx24117: use a valid dev pointer for dev_err printout
[media] cx24117: remove dead code in always 'false' if statement
[media] update Michael Krufky's email address
[media] vb2: Check if there are buffers before streamon
[media] Revert "[media] videobuf_vm_{open,close} race fixes"
[media] go7007-loader: fix usb_dev leak
[media] media: bt8xx: add missing put_device call
[media] exynos4-is: Compile in fimc-lite runtime PM callbacks conditionally
[media] exynos4-is: Compile in fimc runtime PM callbacks conditionally
[media] exynos4-is: Fix error paths in probe() for !pm_runtime_enabled()
[media] s5p-jpeg: Fix wrong NV12 format parameters
[media] s5k5baf: allow to handle arbitrary long i2c sequences
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"Fix PMBus driver problem with some multi-page voltage sensors and fix
da9055 interrupt initialization"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (da9055) Remove use of regmap_irq_get_virq()
hwmon: (pmbus) Support per-page exponent in linear mode
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"These include a fix for a recent ACPI hotplug regression, four
concurrency related fixes and one PCI device removal fix for
ACPI-based PCI hotplug (ACPIPHP), intel_pstate fix that should go into
stable, three simple ACPI cleanups and a new entry for the ACPI video
blacklist.
Specifics:
- Fix for a recent ACPI hotplug regression causing a NULL pointer
dereference to occur while handling ACPI eject notifications for
already ejected devices. From Toshi Kani.
- Four concurrency-related fixes for ACPIPHP. Two of them add
missing locking and the other two fix race conditions related to
reference counting.
- ACPIPHP fix to avoid NULL pointer dereferences during device
removal involving Virtual Funcions.
- intel_pstate fix to make it compute the percentage of time the CPU
is busy properly. From Dirk Brandewie.
- Removal of two unnecessary NULL pointer checks in ACPI code and a
fix for sscanf() format string from Dan Carpenter and Luis G.F.
- New ACPI video blacklist entry for HP EliteBook Revolve 810 from
Mika Westerberg"
* tag 'pm+acpi-3.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / hotplug: Fix panic on eject to ejected device
ACPI / battery: Fix incorrect sscanf() string in acpi_battery_init_alarm()
ACPI / proc: remove unneeded NULL check
ACPI / utils: remove a pointless NULL check
ACPI / video: Add HP EliteBook Revolve 810 to the blacklist
intel_pstate: Take core C0 time into account for core busy calculation
ACPI / hotplug / PCI: Fix bridge removal race vs dock events
ACPI / hotplug / PCI: Fix bridge removal race in handle_hotplug_event()
ACPI / hotplug / PCI: Scan root bus under the PCI rescan-remove lock
ACPI / hotplug / PCI: Move PCI rescan-remove locking to hotplug_event()
ACPI / hotplug / PCI: Remove entries from bus->devices in reverse order
|
|
Commit f38a5181d9f3 ("ceph: Convert to immutable biovecs") introduced
a NULL pointer dereference, which broke rbd in -rc1. Fix it.
Cc: Kent Overstreet <[email protected]>
Signed-off-by: Ilya Dryomov <[email protected]>
Reviewed-by: Sage Weil <[email protected]>
|
|
* Avoid WARN_ON() when mapping BGRT on Baytrail (EFI 32-bit).
Signed-off-by: H. Peter Anvin <[email protected]>
|
|
Handling redirect replies requires both map_sem and request_mutex.
Taking map_sem unconditionally near the top of handle_reply() avoids
possible race conditions that arise from releasing request_mutex to be
able to acquire map_sem in redirect reply case. (Lock ordering is:
map_sem, request_mutex, crush_mutex.)
Signed-off-by: Ilya Dryomov <[email protected]>
Reviewed-by: Sage Weil <[email protected]>
|
|
Factor out logic from ceph_osdc_start_request() into a new helper,
__ceph_osdc_start_request(). ceph_osdc_start_request() now amounts to
taking locks and calling __ceph_osdc_start_request().
Signed-off-by: Ilya Dryomov <[email protected]>
Reviewed-by: Sage Weil <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
FPGA implementations of the Cortex-A57 and Cortex-A53 are now available
in the form of the SMM-A57 and SMM-A53 Soft Macrocell Models (SMMs) for
Versatile Express. As these attach to a Motherboard Express V2M-P1 it
would be useful to have support for some V2M-P1 peripherals enabled by
default.
Additionally a couple of of features have been introduced since the last
defconfig update (CMA, jump labels) that would be good to have enabled
by default to ensure they are build and boot tested.
This patch updates the arm64 defconfig to enable support for these
devices and features. The arm64 Kconfig is modified to select
HAVE_PATA_PLATFORM, which is required to enable support for the
CompactFlash controller on the V2M-P1.
A few options which don't need to appear in defconfig are trimmed:
* BLK_DEV - selected by default
* EXPERIMENTAL - otherwise gone from the kernel
* MII - selected by drivers which require it
* USB_SUPPORT - selected by default
Signed-off-by: Mark Rutland <[email protected]>
Signed-off-by: Catalin Marinas <[email protected]>
|
|
The get/set ACL xattr support for CIFS ACLs attempts to send old
cifs dialect protocol requests even when mounted with SMB2 or later
dialects. Sending cifs requests on an smb2 session causes problems -
the server drops the session due to the illegal request.
This patch makes CIFS ACL operations protocol specific to fix that.
Attempting to query/set CIFS ACLs for SMB2 will now return
EOPNOTSUPP (until we add worker routines for sending query
ACL requests via SMB2) instead of sending invalid (cifs)
requests.
A separate followon patch will be needed to fix cifs_acl_to_fattr
(which takes a cifs specific u16 fid so can't be abstracted
to work with SMB2 until that is changed) and will be needed
to fix mount problems when "cifsacl" is specified on mount
with e.g. vers=2.1
Signed-off-by: Steve French <[email protected]>
Reviewed-by: Shirish Pargaonkar <[email protected]>
CC: Stable <[email protected]>
|
|
Changeset 666753c3ef8fc88b0ddd5be4865d0aa66428ac35 added protocol
operations for get/setxattr to avoid calling cifs operations
on smb2/smb3 mounts for xattr operations and this changeset
adds the calls to cifs specific protocol operations for xattrs
(in order to reenable cifs support for xattrs which was
temporarily disabled by the previous changeset. We do not
have SMB2/SMB3 worker function for setting xattrs yet so
this only enables it for cifs.
CCing stable since without these two small changsets (its
small coreq 666753c3ef8fc88b0ddd5be4865d0aa66428ac35 is
also needed) calling getfattr/setfattr on smb2/smb3 mounts
causes problems.
Signed-off-by: Steve French <[email protected]>
Reviewed-by: Shirish Pargaonkar <[email protected]>
CC: Stable <[email protected]>
|
|
It makes no sense to inline a rarely used function meant for debugging
only that is called a total of five times in the main evaluation loop.
Signed-off-by: Patrick McHardy <[email protected]>
Signed-off-by: Pablo Neira Ayuso <[email protected]>
|
|
cbnz/tbnz don't update the condition flags, so remove the "cc" clobbers
from inline asm blocks that only use these instructions to implement
conditional branches.
Signed-off-by: Will Deacon <[email protected]>
Signed-off-by: Catalin Marinas <[email protected]>
|
|
Linux requires a number of atomic operations to provide full barrier
semantics, that is no memory accesses after the operation can be
observed before any accesses up to and including the operation in
program order.
On arm64, these operations have been incorrectly implemented as follows:
// A, B, C are independent memory locations
<Access [A]>
// atomic_op (B)
1: ldaxr x0, [B] // Exclusive load with acquire
<op(B)>
stlxr w1, x0, [B] // Exclusive store with release
cbnz w1, 1b
<Access [C]>
The assumption here being that two half barriers are equivalent to a
full barrier, so the only permitted ordering would be A -> B -> C
(where B is the atomic operation involving both a load and a store).
Unfortunately, this is not the case by the letter of the architecture
and, in fact, the accesses to A and C are permitted to pass their
nearest half barrier resulting in orderings such as Bl -> A -> C -> Bs
or Bl -> C -> A -> Bs (where Bl is the load-acquire on B and Bs is the
store-release on B). This is a clear violation of the full barrier
requirement.
The simple way to fix this is to implement the same algorithm as ARMv7
using explicit barriers:
<Access [A]>
// atomic_op (B)
dmb ish // Full barrier
1: ldxr x0, [B] // Exclusive load
<op(B)>
stxr w1, x0, [B] // Exclusive store
cbnz w1, 1b
dmb ish // Full barrier
<Access [C]>
but this has the undesirable effect of introducing *two* full barrier
instructions. A better approach is actually the following, non-intuitive
sequence:
<Access [A]>
// atomic_op (B)
1: ldxr x0, [B] // Exclusive load
<op(B)>
stlxr w1, x0, [B] // Exclusive store with release
cbnz w1, 1b
dmb ish // Full barrier
<Access [C]>
The simple observations here are:
- The dmb ensures that no subsequent accesses (e.g. the access to C)
can enter or pass the atomic sequence.
- The dmb also ensures that no prior accesses (e.g. the access to A)
can pass the atomic sequence.
- Therefore, no prior access can pass a subsequent access, or
vice-versa (i.e. A is strictly ordered before C).
- The stlxr ensures that no prior access can pass the store component
of the atomic operation.
The only tricky part remaining is the ordering between the ldxr and the
access to A, since the absence of the first dmb means that we're now
permitting re-ordering between the ldxr and any prior accesses.
From an (arbitrary) observer's point of view, there are two scenarios:
1. We have observed the ldxr. This means that if we perform a store to
[B], the ldxr will still return older data. If we can observe the
ldxr, then we can potentially observe the permitted re-ordering
with the access to A, which is clearly an issue when compared to
the dmb variant of the code. Thankfully, the exclusive monitor will
save us here since it will be cleared as a result of the store and
the ldxr will retry. Notice that any use of a later memory
observation to imply observation of the ldxr will also imply
observation of the access to A, since the stlxr/dmb ensure strict
ordering.
2. We have not observed the ldxr. This means we can perform a store
and influence the later ldxr. However, that doesn't actually tell
us anything about the access to [A], so we've not lost anything
here either when compared to the dmb variant.
This patch implements this solution for our barriered atomic operations,
ensuring that we satisfy the full barrier requirements where they are
needed.
Cc: <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Signed-off-by: Will Deacon <[email protected]>
Signed-off-by: Catalin Marinas <[email protected]>
|
|
Fix access to uninitialized data for end interval elements. The
element data part is uninitialized in interval end elements.
Signed-off-by: Pablo Neira Ayuso <[email protected]>
|
|
This patch fixes several things which related to the handling of
end interval elements:
* Chain use underflow with intervals and map: If you add a rule
using intervals+map that introduces a loop, the error path of the
rbtree set decrements the chain refcount for each side of the
interval, leading to a chain use counter underflow.
* Don't copy the data part of the end interval element since, this
area is uninitialized and this confuses the loop detection code.
* Don't allocate room for the data part of end interval elements
since this is unused.
So, after this patch the idea is that end interval elements don't
have a data part.
Signed-off-by: Pablo Neira Ayuso <[email protected]>
Acked-by: Patrick McHardy <[email protected]>
|
|
This combination is not allowed since end interval elements cannot
contain data.
Signed-off-by: Pablo Neira Ayuso <[email protected]>
Acked-by: Patrick McHardy <[email protected]>
|
|
TCP pacing depends on an accurate srtt estimation.
Current srtt estimation is using jiffie resolution,
and has an artificial offset of at least 1 ms, which can produce
slowdowns when FQ/pacing is used, especially in DC world,
where typical rtt is below 1 ms.
We are planning a switch to usec resolution for linux-3.15,
but in the meantime, this patch removes the 1 ms offset.
All we need is to have tp->srtt minimal value of 1 to differentiate
the case of srtt being initialized or not, not 8.
The problematic behavior was observed on a 40Gbit testbed,
where 32 concurrent netperf were reaching 12Gbps of aggregate
speed, instead of line speed.
This patch also has the effect of reporting more accurate srtt and send
rates to iproute2 ss command as in :
$ ss -i dst cca2
Netid State Recv-Q Send-Q Local Address:Port
Peer Address:Port
tcp ESTAB 0 0 10.244.129.1:56984
10.244.129.2:12865
cubic wscale:6,6 rto:200 rtt:0.25/0.25 ato:40 mss:1448 cwnd:10 send
463.4Mbps rcv_rtt:1 rcv_space:29200
tcp ESTAB 0 390960 10.244.129.1:60247
10.244.129.2:50204
cubic wscale:6,6 rto:200 rtt:0.875/0.75 mss:1448 cwnd:73 ssthresh:51
send 966.4Mbps unacked:73 retrans:0/121 rcv_space:29200
Reported-by: Vytautas Valancius <[email protected]>
Signed-off-by: Eric Dumazet <[email protected]>
Cc: Yuchung Cheng <[email protected]>
Cc: Neal Cardwell <[email protected]>
Acked-by: Neal Cardwell <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Commit 93d8bf9fb8f3 ("bridge: cleanup netpoll code") introduced
a check in br_netpoll_enable(), but this check is incorrect for
br_netpoll_setup(). This patch moves the code after the check
into __br_netpoll_enable() and calls it in br_netpoll_setup().
For br_add_if(), the check is still needed.
Fixes: 93d8bf9fb8f3 ("bridge: cleanup netpoll code")
Cc: Toshiaki Makita <[email protected]>
Cc: Stephen Hemminger <[email protected]>
Cc: David S. Miller <[email protected]>
Signed-off-by: Cong Wang <[email protected]>
Signed-off-by: Cong Wang <[email protected]>
Acked-by: Toshiaki Makita <[email protected]>
Tested-by: Toshiaki Makita <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
sock_alloc_send_pskb() & sk_page_frag_refill()
have a loop trying high order allocations to prepare
skb with low number of fragments as this increases performance.
Problem is that under memory pressure/fragmentation, this can
trigger OOM while the intent was only to try the high order
allocations, then fallback to order-0 allocations.
We had various reports from unexpected regressions.
According to David, setting __GFP_NORETRY should be fine,
as the asynchronous compaction is still enabled, and this
will prevent OOM from kicking as in :
CFSClientEventm invoked oom-killer: gfp_mask=0x42d0, order=3, oom_adj=0,
oom_score_adj=0, oom_score_badness=2 (enabled),memcg_scoring=disabled
CFSClientEventm
Call Trace:
[<ffffffff8043766c>] dump_header+0xe1/0x23e
[<ffffffff80437a02>] oom_kill_process+0x6a/0x323
[<ffffffff80438443>] out_of_memory+0x4b3/0x50d
[<ffffffff8043a4a6>] __alloc_pages_may_oom+0xa2/0xc7
[<ffffffff80236f42>] __alloc_pages_nodemask+0x1002/0x17f0
[<ffffffff8024bd23>] alloc_pages_current+0x103/0x2b0
[<ffffffff8028567f>] sk_page_frag_refill+0x8f/0x160
[<ffffffff80295fa0>] tcp_sendmsg+0x560/0xee0
[<ffffffff802a5037>] inet_sendmsg+0x67/0x100
[<ffffffff80283c9c>] __sock_sendmsg_nosec+0x6c/0x90
[<ffffffff80283e85>] sock_sendmsg+0xc5/0xf0
[<ffffffff802847b6>] __sys_sendmsg+0x136/0x430
[<ffffffff80284ec8>] sys_sendmsg+0x88/0x110
[<ffffffff80711472>] system_call_fastpath+0x16/0x1b
Out of Memory: Kill process 2856 (bash) score 9999 or sacrifice child
Signed-off-by: Eric Dumazet <[email protected]>
Acked-by: David Rientjes <[email protected]>
Acked-by: "Eric W. Biederman" <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Currently, to make netconsole start over IPv6, the source address
needs to be specified. Without a source address, netpoll_parse_options
assumes we're setting up over IPv4 and the destination IPv6 address is
rejected.
Check if the IP version has been forced by a source address before
checking for a version mismatch when parsing the destination address.
Signed-off-by: Sabrina Dubroca <[email protected]>
Acked-by: Cong Wang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Commit ee45fd92c739db5b7950163d91dfe5f016af6d24 ("sfc: Use TX PIO
for sufficiently small packets") introduced the following warning:
drivers/net/ethernet/sfc/tx.c: In function 'efx_enqueue_skb':
drivers/net/ethernet/sfc/tx.c:432:1: warning: label 'finish_packet' defined but not used
Stick the label inside the same #ifdef that the code which calls
it uses. Note that this is only seen for arch that do not set
ARCH_HAS_IOREMAP_WC, such as arm, mips, sparc, ..., as the others
enable the write combining code and hence use the label.
Cc: Jon Cooper <[email protected]>
Cc: Ben Hutchings <[email protected]>
Signed-off-by: Paul Gortmaker <[email protected]>
Acked-by: Shradha Shah <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
It seems like this function was intended to have special handling for
urb statuses of -ENOENT and -ECONNRESET. But now it just prints some
debugging and returns at the start of the function.
I have removed the dead code, it's still in the git history if anyone
wants to revive it.
Signed-off-by: Dan Carpenter <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Commit cfd280c91253 ("net: sync some IP headers with glibc") changed a set of
define's to an enum (with no explanation why) which introduced a bug
in module mip6 where aliases are generated using the IPPROTO_* defines;
mip6 doesn't load if require_module called with the aliases from
xfrm_get_type().
Reverting this change back to define's to fix the aliases.
modinfo mip6 (before this change)
alias: xfrm-type-10-IPPROTO_DSTOPTS
alias: xfrm-type-10-IPPROTO_ROUTING
modinfo mip6 (after this change)
alias: xfrm-type-10-43
alias: xfrm-type-10-60
Signed-off-by: Jan Moskyto Matejka <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This is a static checker fix, but judging from the context then I think
hexidecimal 0x80 is intended here instead of decimal 80.
Signed-off-by: Dan Carpenter <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
commit efe4208f47f907b86f528788da711e8ab9dea44d:
'ipv6: make lookups simpler and faster' broke initialization of local source
address on accepted ipv6 sockets. Before the mentioned commit receive address
was copied along with the contents of ipv6_pinfo in sctp_v6_create_accept_sk.
Now when it is moved, it has to be copied separately.
This also fixes lksctp's ipv6 regression in a sense that test_getname_v6, TC5 -
'getsockname on a connected server socket' now passes.
Signed-off-by: Matija Glavinic Pecotic <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The submission of the interrupt transfer should be done after setting
the bit of WORK_ENABLE, otherwise the callback function would have
the opportunity to be returned directly.
Clear the bit of WORK_ENABLE before killing the interrupt transfer.
Signed-off-by: Hayes Wang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
bnx2x driver uses incorrect PF identifier to configure (in HW) the VF
interrupt scheme; As a result, in multi-function mode the configuration
for PFs with a high index (4+) will overflow and the PF will erroneously
configure a single ISR scheme for its VFs.
As a result, if such a VF uses multiple queues, interrupt generation will
stop after VF receives an Rx packet or sends a Tx packet on a queue
other than queue[0].
Signed-off-by: Yuval Mintz <[email protected]>
Signed-off-by: Ariel Elior <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Quoting David Vrabel -
"5780 cards cannot have jumbo frames and TSO enabled together. When
jumbo frames are enabled by setting the MTU, the TSO feature must be
cleared. This is done indirectly by calling netdev_update_features()
which will call tg3_fix_features() to actually clear the flags.
netdev_update_features() will also trigger a new netlink message for the
feature change event which will result in a call to tg3_get_stats64()
which deadlocks on the tg3 lock."
tg3_set_mtu() does not need to be under the tg3 lock since converting
the flags to use set_bit(). Move it out to after tg3_netif_stop().
Reported-by: David Vrabel <[email protected]>
Tested-by: David Vrabel <[email protected]>
Signed-off-by: Michael Chan <[email protected]>
Signed-off-by: Nithin Nayak Sujir <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In the original code, if tg3_readphy() fails then it does an unnecessary
check to verify "err" is still zero and then returns -EBUSY.
My static checker complains about the unnecessary "if (!err)" check and
anyway it is better to propagate the -EBUSY error code from
tg3_readphy() instead of hard coding it here. And really the original
code is confusing to look at.
Signed-off-by: Dan Carpenter <[email protected]>
Acked-by: Nithin Nayak Sujir <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
On m68k/ARAnyM:
WARNING: CPU: 0 PID: 407 at net/ipv4/devinet.c:1599 0x316a99()
Modules linked in:
CPU: 0 PID: 407 Comm: ifconfig Not tainted
3.13.0-atari-09263-g0c71d68014d1 #1378
Stack from 10c4fdf0:
10c4fdf0 002ffabb 000243e8 00000000 008ced6c 00024416 00316a99 0000063f
00316a99 00000009 00000000 002501b4 00316a99 0000063f c0a86117 00000080
c0a86117 00ad0c90 00250a5a 00000014 00ad0c90 00000000 00000000 00000001
00b02dd0 00356594 00000000 00356594 c0a86117 eff6c9e4 008ced6c 00000002
008ced60 0024f9b4 00250b52 00ad0c90 00000000 00000000 00252390 00ad0c90
eff6c9e4 0000004f 00000000 00000000 eff6c9e4 8000e25c eff6c9e4 80001020
Call Trace: [<000243e8>] warn_slowpath_common+0x52/0x6c
[<00024416>] warn_slowpath_null+0x14/0x1a
[<002501b4>] rtmsg_ifa+0xdc/0xf0
[<00250a5a>] __inet_insert_ifa+0xd6/0x1c2
[<0024f9b4>] inet_abc_len+0x0/0x42
[<00250b52>] inet_insert_ifa+0xc/0x12
[<00252390>] devinet_ioctl+0x2ae/0x5d6
Adding some debugging code reveals that net_fill_ifaddr() fails in
put_cacheinfo(skb, ifa->ifa_cstamp, ifa->ifa_tstamp,
preferred, valid))
nla_put complains:
lib/nlattr.c:454: skb_tailroom(skb) = 12, nla_total_size(attrlen) = 20
Apparently commit 5c766d642bcaffd0c2a5b354db2068515b3846cf ("ipv4:
introduce address lifetime") forgot to take into account the addition of
struct ifa_cacheinfo in inet_nlmsg_size(). Hence add it, like is already
done for ipv6.
Suggested-by: Cong Wang <[email protected]>
Signed-off-by: Geert Uytterhoeven <[email protected]>
Signed-off-by: Cong Wang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Occasionally users want to know what parameters their Broadcom drivers
are running with. For example, a user may want to know if MSI is
disabled.
This patch has been compile tested.
Signed-off-by: James M Leddy <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This patch removes old and unsupported CLPS711X IrDA driver.
Support for IrDA for CLPS711X serial port now provided by commit
4a33f1f59abd (serial: clps711x: Add support for N_IRDA line
discipline), so IrDA-mode can be turned ON with "irattach" tool
through "irtty" driver.
Signed-off-by: Alexander Shiyan <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Switch the device tree to the new compatibles introduced in the ethernet and
mdio drivers to have a common pattern accross all Allwinner SoCs.
Signed-off-by: Maxime Ripard <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The Allwinner A10 compatibles were following a slightly different compatible
patterns than the rest of the SoCs for historical reasons. Add compatibles
matching the other pattern to the mdio driver for consistency, and keep the
older one for backward compatibility.
Signed-off-by: Maxime Ripard <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The Allwinner A10 compatibles were following a slightly different compatible
patterns than the rest of the SoCs for historical reasons. Add compatibles
matching the other pattern to the ethernet driver for consistency, and keep the
older one for backward compatibility.
Signed-off-by: Maxime Ripard <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Remove use of regmap_irq_get_virq() in driver probe which was
conflicting with use of platform_get_irq_byname().
platform_get_irq_byname() already returns the VIRQ number due
to MFD core translation so using regmap_irq_get_virq() on that
returned value results in an incorrect IRQ being requested.
The driver probes then fail because of this.
Signed-off-by: Adam Thomson <[email protected]>
Signed-off-by: Guenter Roeck <[email protected]>
|
|
* acpi-cleanup:
ACPI / battery: Fix incorrect sscanf() string in acpi_battery_init_alarm()
ACPI / proc: remove unneeded NULL check
ACPI / utils: remove a pointless NULL check
* acpi-video:
ACPI / video: Add HP EliteBook Revolve 810 to the blacklist
|
|
* pm-cpufreq:
intel_pstate: Take core C0 time into account for core busy calculation
|
|
* acpi-pci-hotplug:
ACPI / hotplug / PCI: Fix bridge removal race vs dock events
ACPI / hotplug / PCI: Fix bridge removal race in handle_hotplug_event()
ACPI / hotplug / PCI: Scan root bus under the PCI rescan-remove lock
ACPI / hotplug / PCI: Move PCI rescan-remove locking to hotplug_event()
ACPI / hotplug / PCI: Remove entries from bus->devices in reverse order
* acpi-hotplug:
ACPI / hotplug: Fix panic on eject to ejected device
|
|
Merge a bunch of fixes from Andrew Morton:
"Commit 579f82901f6f ("swap: add a simple detector for inappropriate
swapin readahead") is a feature. No probs if you decide to defer it
until the next merge window.
It has been sitting in my tree for over a year because of my dislike
of all the magic numbers, but recent discussion with Hugh has made me
give up"
* emailed patches fron Andrew Morton <[email protected]>:
mm: __set_page_dirty uses spin_lock_irqsave instead of spin_lock_irq
arch/x86/mm/numa.c: fix array index overflow when synchronizing nid to memblock.reserved.
arch/x86/mm/numa.c: initialize numa_kernel_nodes in numa_clear_kernel_node_hotplug()
mm: __set_page_dirty_nobuffers() uses spin_lock_irqsave() instead of spin_lock_irq()
mm/swap: fix race on swap_info reuse between swapoff and swapon
swap: add a simple detector for inappropriate swapin readahead
ocfs2: free allocated clusters if error occurs after ocfs2_claim_clusters
Documentation/kernel-parameters.txt: fix memmap= language
|
|
To use spin_{un}lock_irq is dangerous if caller disabled interrupt.
During aio buffer migration, we have a possibility to see the following
call stack.
aio_migratepage [disable interrupt]
migrate_page_copy
clear_page_dirty_for_io
set_page_dirty
__set_page_dirty_buffers
__set_page_dirty
spin_lock_irq
This mean, current aio migration is a deadlockable. spin_lock_irqsave
is a safer alternative and we should use it.
Signed-off-by: KOSAKI Motohiro <[email protected]>
Reported-by: David Rientjes [email protected]>
Cc: <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
memblock.reserved.
The following path will cause array out of bound.
memblock_add_region() will always set nid in memblock.reserved to
MAX_NUMNODES. In numa_register_memblks(), after we set all nid to
correct valus in memblock.reserved, we called setup_node_data(), and
used memblock_alloc_nid() to allocate memory, with nid set to
MAX_NUMNODES.
The nodemask_t type can be seen as a bit array. And the index is 0 ~
MAX_NUMNODES-1.
After that, when we call node_set() in numa_clear_kernel_node_hotplug(),
the nodemask_t got an index of value MAX_NUMNODES, which is out of [0 ~
MAX_NUMNODES-1].
See below:
numa_init()
|---> numa_register_memblks()
| |---> memblock_set_node(memory) set correct nid in memblock.memory
| |---> memblock_set_node(reserved) set correct nid in memblock.reserved
| |......
| |---> setup_node_data()
| |---> memblock_alloc_nid() here, nid is set to MAX_NUMNODES (1024)
|......
|---> numa_clear_kernel_node_hotplug()
|---> node_set() here, we have an index 1024, and overflowed
This patch moves nid setting to numa_clear_kernel_node_hotplug() to fix
this problem.
Reported-by: Dave Jones <[email protected]>
Signed-off-by: Tang Chen <[email protected]>
Tested-by: Gu Zheng <[email protected]>
Reported-by: Dave Jones <[email protected]>
Cc: David Rientjes <[email protected]>
Tested-by: Dave Jones <[email protected]>
Cc: Ingo Molnar <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: "H. Peter Anvin" <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|