| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Lan966x is adding ptp traps to redirect the ptp frames to the CPU such
that the HW will not forward these frames anywhere. The issue is that in
case ptp is not enabled and the timestamping source is et to
HWTSTAMP_SOURCE_NETDEV then these traps would not be removed on the
error path.
Fix this by removing the traps in this case as they are not needed.
Fixes: 54e1ed69c40a ("net: lan966x: convert to ndo_hwtstamp_get() and ndo_hwtstamp_set()")
Suggested-by: Vladimir Oltean <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Signed-off-by: Horatiu Vultur <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Paolo Abeni <[email protected]>
|
|
Open vSwitch is originally intended to switch at layer 2, only dealing with
Ethernet frames. With the introduction of l3 tunnels support, it crossed
into the realm of needing to care a bit about some routing details when
making forwarding decisions. If an oversized packet would need to be
fragmented during this forwarding decision, there is a chance for pmtu
to get involved and generate a routing exception. This is gated by the
skbuff->pkt_type field.
When a flow is already loaded into the openvswitch module this field is
set up and transitioned properly as a packet moves from one port to
another. In the case that a packet execute is invoked after a flow is
newly installed this field is not properly initialized. This causes the
pmtud mechanism to omit sending the required exception messages across
the tunnel boundary and a second attempt needs to be made to make sure
that the routing exception is properly setup. To fix this, we set the
outgoing packet's pkt_type to PACKET_OUTGOING, since it can only get
to the openvswitch module via a port device or packet command.
Even for bridge ports as users, the pkt_type needs to be reset when
doing the transmit as the packet is truly outgoing and routing needs
to get involved post packet transformations, in the case of
VXLAN/GENEVE/udp-tunnel packets. In general, the pkt_type on output
gets ignored, since we go straight to the driver, but in the case of
tunnel ports they go through IP routing layer.
This issue is periodically encountered in complex setups, such as large
openshift deployments, where multiple sets of tunnel traversal occurs.
A way to recreate this is with the ovn-heater project that can setup
a networking environment which mimics such large deployments. We need
larger environments for this because we need to ensure that flow
misses occur. In these environment, without this patch, we can see:
./ovn_cluster.sh start
podman exec ovn-chassis-1 ip r a 170.168.0.5/32 dev eth1 mtu 1200
podman exec ovn-chassis-1 ip netns exec sw01p1 ip r flush cache
podman exec ovn-chassis-1 ip netns exec sw01p1 \
ping 21.0.0.3 -M do -s 1300 -c2
PING 21.0.0.3 (21.0.0.3) 1300(1328) bytes of data.
From 21.0.0.3 icmp_seq=2 Frag needed and DF set (mtu = 1142)
--- 21.0.0.3 ping statistics ---
...
Using tcpdump, we can also see the expected ICMP FRAG_NEEDED message is not
sent into the server.
With this patch, setting the pkt_type, we see the following:
podman exec ovn-chassis-1 ip netns exec sw01p1 \
ping 21.0.0.3 -M do -s 1300 -c2
PING 21.0.0.3 (21.0.0.3) 1300(1328) bytes of data.
From 21.0.0.3 icmp_seq=1 Frag needed and DF set (mtu = 1222)
ping: local error: message too long, mtu=1222
--- 21.0.0.3 ping statistics ---
...
In this case, the first ping request receives the FRAG_NEEDED message and
a local routing exception is created.
Tested-by: Jaime Caamano <[email protected]>
Reported-at: https://issues.redhat.com/browse/FDP-164
Fixes: 58264848a5a7 ("openvswitch: Add vxlan tunneling support.")
Signed-off-by: Aaron Conole <[email protected]>
Acked-by: Eelco Chaudron <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Paolo Abeni <[email protected]>
|
|
Michal Luczaj says:
====================
af_unix: Fix GC and improve selftest
Series deals with AF_UNIX garbage collector mishandling some in-flight
graph cycles. Embryos carrying OOB packets with SCM_RIGHTS cause issues.
Patch 1/2 fixes the memory leak.
Patch 2/2 tweaks the selftest for a better OOB coverage.
v3:
- Patch 1/2: correct the commit message (Kuniyuki)
v2: https://lore.kernel.org/netdev/[email protected]/
- Patch 1/2: remove WARN_ON_ONCE() (Kuniyuki)
- Combine both patches into a series (Kuniyuki)
v1: https://lore.kernel.org/netdev/[email protected]/
====================
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Paolo Abeni <[email protected]>
|
|
scm_rights.c covers various test cases for inflight file descriptors
and garbage collector for AF_UNIX sockets.
Currently, SCM_RIGHTS messages are sent with 3-bytes string, and it's
not good for MSG_OOB cases, as SCM_RIGTS cmsg goes with the first 2-bytes,
which is non-OOB data.
Let's send SCM_RIGHTS messages with 1-byte character to pack SCM_RIGHTS
into OOB data.
Signed-off-by: Kuniyuki Iwashima <[email protected]>
Signed-off-by: Michal Luczaj <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
|
|
GC attempts to explicitly drop oob_skb's reference before purging the hit
list.
The problem is with embryos: kfree_skb(u->oob_skb) is never called on an
embryo socket.
The python script below [0] sends a listener's fd to its embryo as OOB
data. While GC does collect the embryo's queue, it fails to drop the OOB
skb's refcount. The skb which was in embryo's receive queue stays as
unix_sk(sk)->oob_skb and keeps the listener's refcount [1].
Tell GC to dispose embryo's oob_skb.
[0]:
from array import array
from socket import *
addr = '\x00unix-oob'
lis = socket(AF_UNIX, SOCK_STREAM)
lis.bind(addr)
lis.listen(1)
s = socket(AF_UNIX, SOCK_STREAM)
s.connect(addr)
scm = (SOL_SOCKET, SCM_RIGHTS, array('i', [lis.fileno()]))
s.sendmsg([b'x'], [scm], MSG_OOB)
lis.close()
[1]
$ grep unix-oob /proc/net/unix
$ ./unix-oob.py
$ grep unix-oob /proc/net/unix
0000000000000000: 00000002 00000000 00000000 0001 02 0 @unix-oob
0000000000000000: 00000002 00000000 00010000 0001 01 6072 @unix-oob
Fixes: 4090fa373f0e ("af_unix: Replace garbage collection algorithm.")
Signed-off-by: Michal Luczaj <[email protected]>
Reviewed-by: Kuniyuki Iwashima <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
|
|
In dctcp_update_alpha(), we use a module parameter dctcp_shift_g
as follows:
alpha -= min_not_zero(alpha, alpha >> dctcp_shift_g);
...
delivered_ce <<= (10 - dctcp_shift_g);
It seems syzkaller started fuzzing module parameters and triggered
shift-out-of-bounds [0] by setting 100 to dctcp_shift_g:
memcpy((void*)0x20000080,
"/sys/module/tcp_dctcp/parameters/dctcp_shift_g\000", 47);
res = syscall(__NR_openat, /*fd=*/0xffffffffffffff9cul, /*file=*/0x20000080ul,
/*flags=*/2ul, /*mode=*/0ul);
memcpy((void*)0x20000000, "100\000", 4);
syscall(__NR_write, /*fd=*/r[0], /*val=*/0x20000000ul, /*len=*/4ul);
Let's limit the max value of dctcp_shift_g by param_set_uint_minmax().
With this patch:
# echo 10 > /sys/module/tcp_dctcp/parameters/dctcp_shift_g
# cat /sys/module/tcp_dctcp/parameters/dctcp_shift_g
10
# echo 11 > /sys/module/tcp_dctcp/parameters/dctcp_shift_g
-bash: echo: write error: Invalid argument
[0]:
UBSAN: shift-out-of-bounds in net/ipv4/tcp_dctcp.c:143:12
shift exponent 100 is too large for 32-bit type 'u32' (aka 'unsigned int')
CPU: 0 PID: 8083 Comm: syz-executor345 Not tainted 6.9.0-05151-g1b294a1f3561 #2
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
1.13.0-1ubuntu1.1 04/01/2014
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x201/0x300 lib/dump_stack.c:114
ubsan_epilogue lib/ubsan.c:231 [inline]
__ubsan_handle_shift_out_of_bounds+0x346/0x3a0 lib/ubsan.c:468
dctcp_update_alpha+0x540/0x570 net/ipv4/tcp_dctcp.c:143
tcp_in_ack_event net/ipv4/tcp_input.c:3802 [inline]
tcp_ack+0x17b1/0x3bc0 net/ipv4/tcp_input.c:3948
tcp_rcv_state_process+0x57a/0x2290 net/ipv4/tcp_input.c:6711
tcp_v4_do_rcv+0x764/0xc40 net/ipv4/tcp_ipv4.c:1937
sk_backlog_rcv include/net/sock.h:1106 [inline]
__release_sock+0x20f/0x350 net/core/sock.c:2983
release_sock+0x61/0x1f0 net/core/sock.c:3549
mptcp_subflow_shutdown+0x3d0/0x620 net/mptcp/protocol.c:2907
mptcp_check_send_data_fin+0x225/0x410 net/mptcp/protocol.c:2976
__mptcp_close+0x238/0xad0 net/mptcp/protocol.c:3072
mptcp_close+0x2a/0x1a0 net/mptcp/protocol.c:3127
inet_release+0x190/0x1f0 net/ipv4/af_inet.c:437
__sock_release net/socket.c:659 [inline]
sock_close+0xc0/0x240 net/socket.c:1421
__fput+0x41b/0x890 fs/file_table.c:422
task_work_run+0x23b/0x300 kernel/task_work.c:180
exit_task_work include/linux/task_work.h:38 [inline]
do_exit+0x9c8/0x2540 kernel/exit.c:878
do_group_exit+0x201/0x2b0 kernel/exit.c:1027
__do_sys_exit_group kernel/exit.c:1038 [inline]
__se_sys_exit_group kernel/exit.c:1036 [inline]
__x64_sys_exit_group+0x3f/0x40 kernel/exit.c:1036
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xe4/0x240 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x67/0x6f
RIP: 0033:0x7f6c2b5005b6
Code: Unable to access opcode bytes at 0x7f6c2b50058c.
RSP: 002b:00007ffe883eb948 EFLAGS: 00000246 ORIG_RAX: 00000000000000e7
RAX: ffffffffffffffda RBX: 00007f6c2b5862f0 RCX: 00007f6c2b5005b6
RDX: 0000000000000001 RSI: 000000000000003c RDI: 0000000000000001
RBP: 0000000000000001 R08: 00000000000000e7 R09: ffffffffffffffc0
R10: 0000000000000006 R11: 0000000000000246 R12: 00007f6c2b5862f0
R13: 0000000000000001 R14: 0000000000000000 R15: 0000000000000001
</TASK>
Reported-by: syzkaller <[email protected]>
Reported-by: Yue Sun <[email protected]>
Reported-by: xingwei lee <[email protected]>
Closes: https://lore.kernel.org/netdev/CAEkJfYNJM=cw-8x7_Vmj1J6uYVCWMbbvD=EFmDPVBGpTsqOxEA@mail.gmail.com/
Fixes: e3118e8359bb ("net: tcp: add DCTCP congestion control algorithm")
Signed-off-by: Kuniyuki Iwashima <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Paolo Abeni <[email protected]>
|
|
Test arp_ndisc_untracked_subnets use tcpdump to filter the unsolicited
and untracked na messages. It set -e before calling tcpdump. But if
tcpdump filters 0 packet, it will return none zero, and cause the script
to exit.
Instead of using slow tcpdump to capture packets, let's using tc rule
to filter out the na message.
At the same time, fix function setup_v6 which only needs one parameter.
Move all the related helpers from forwarding lib.sh to net lib.sh.
Fixes: 0ea7b0a454ca ("selftests: net: arp_ndisc_untracked_subnets: test for arp_accept and accept_untracked_na")
Signed-off-by: Hangbin Liu <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Paolo Abeni <[email protected]>
|
|
seg6_hmac_init_algo returns without cleaning up the previous allocations
if one fails, so it's going to leak all that memory and the crypto tfms.
Update seg6_hmac_exit to only free the memory when allocated, so we can
reuse the code directly.
Fixes: bf355b8d2c30 ("ipv6: sr: add core files for SR HMAC support")
Reported-by: Sabrina Dubroca <[email protected]>
Closes: https://lore.kernel.org/netdev/Zj3bh-gE7eT6V6aH@hog/
Signed-off-by: Hangbin Liu <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Reviewed-by: Sabrina Dubroca <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Paolo Abeni <[email protected]>
|
|
Billy Jheng Bing-Jhong reported a race between __unix_gc() and
queue_oob().
__unix_gc() tries to garbage-collect close()d inflight sockets,
and then if the socket has MSG_OOB in unix_sk(sk)->oob_skb, GC
will drop the reference and set NULL to it locklessly.
However, the peer socket still can send MSG_OOB message and
queue_oob() can update unix_sk(sk)->oob_skb concurrently, leading
NULL pointer dereference. [0]
To fix the issue, let's update unix_sk(sk)->oob_skb under the
sk_receive_queue's lock and take it everywhere we touch oob_skb.
Note that we defer kfree_skb() in manage_oob() to silence lockdep
false-positive (See [1]).
[0]:
BUG: kernel NULL pointer dereference, address: 0000000000000008
PF: supervisor write access in kernel mode
PF: error_code(0x0002) - not-present page
PGD 8000000009f5e067 P4D 8000000009f5e067 PUD 9f5d067 PMD 0
Oops: 0002 [#1] PREEMPT SMP PTI
CPU: 3 PID: 50 Comm: kworker/3:1 Not tainted 6.9.0-rc5-00191-gd091e579b864 #110
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014
Workqueue: events delayed_fput
RIP: 0010:skb_dequeue (./include/linux/skbuff.h:2386 ./include/linux/skbuff.h:2402 net/core/skbuff.c:3847)
Code: 39 e3 74 3e 8b 43 10 48 89 ef 83 e8 01 89 43 10 49 8b 44 24 08 49 c7 44 24 08 00 00 00 00 49 8b 14 24 49 c7 04 24 00 00 00 00 <48> 89 42 08 48 89 10 e8 e7 c5 42 00 4c 89 e0 5b 5d 41 5c c3 cc cc
RSP: 0018:ffffc900001bfd48 EFLAGS: 00000002
RAX: 0000000000000000 RBX: ffff8880088f5ae8 RCX: 00000000361289f9
RDX: 0000000000000000 RSI: 0000000000000206 RDI: ffff8880088f5b00
RBP: ffff8880088f5b00 R08: 0000000000080000 R09: 0000000000000001
R10: 0000000000000003 R11: 0000000000000001 R12: ffff8880056b6a00
R13: ffff8880088f5280 R14: 0000000000000001 R15: ffff8880088f5a80
FS: 0000000000000000(0000) GS:ffff88807dd80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000008 CR3: 0000000006314000 CR4: 00000000007506f0
PKRU: 55555554
Call Trace:
<TASK>
unix_release_sock (net/unix/af_unix.c:654)
unix_release (net/unix/af_unix.c:1050)
__sock_release (net/socket.c:660)
sock_close (net/socket.c:1423)
__fput (fs/file_table.c:423)
delayed_fput (fs/file_table.c:444 (discriminator 3))
process_one_work (kernel/workqueue.c:3259)
worker_thread (kernel/workqueue.c:3329 kernel/workqueue.c:3416)
kthread (kernel/kthread.c:388)
ret_from_fork (arch/x86/kernel/process.c:153)
ret_from_fork_asm (arch/x86/entry/entry_64.S:257)
</TASK>
Modules linked in:
CR2: 0000000000000008
Link: https://lore.kernel.org/netdev/[email protected]/ [1]
Fixes: 1279f9d9dec2 ("af_unix: Call kfree_skb() for dead unix_(sk)->oob_skb in GC.")
Reported-by: Billy Jheng Bing-Jhong <[email protected]>
Signed-off-by: Kuniyuki Iwashima <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Paolo Abeni <[email protected]>
|
|
This reverts commit 7274c4147afbf46f45b8501edbdad6da8cd013b9.
Ken reported that RTL8125b can lock up if gro_flush_timeout has the
default value of 20000 and napi_defer_hard_irqs is set to 0.
In this scenario device interrupts aren't disabled, what seems to
trigger some silicon bug under heavy load. I was able to reproduce this
behavior on RTL8168h. Fix this by reverting 7274c4147afb.
Fixes: 7274c4147afb ("r8169: don't try to disable interrupts if NAPI is scheduled already")
Cc: [email protected]
Reported-by: Ken Milmore <[email protected]>
Signed-off-by: Heiner Kallweit <[email protected]>
Reviewed-by: Eric Dumazet <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Paolo Abeni <[email protected]>
|
|
syzbot reported the following uninit-value access issue [1]
nci_rx_work() parses received packet from ndev->rx_q. It should be
validated header size, payload size and total packet size before
processing the packet. If an invalid packet is detected, it should be
silently discarded.
Fixes: d24b03535e5e ("nfc: nci: Fix uninit-value in nci_dev_up and nci_ntf_packet")
Reported-and-tested-by: [email protected]
Closes: https://syzkaller.appspot.com/bug?extid=d7b4dc6cd50410152534 [1]
Signed-off-by: Ryosuke Yasuoka <[email protected]>
Reviewed-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The amt.sh requires smcrouted for multicasting routing.
So, it starts smcrouted before forwarding tests.
It must be stopped after all tests, but it isn't.
To fix this issue, it kills smcrouted in the cleanup logic.
Fixes: c08e8baea78e ("selftests: add amt interface selftest script")
Signed-off-by: Taehee Yoo <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The seg6_input() function is responsible for adding the SRH into a
packet, delegating the operation to the seg6_input_core(). This function
uses the skb_cow_head() to ensure that there is sufficient headroom in
the sk_buff for accommodating the link-layer header.
In the event that the skb_cow_header() function fails, the
seg6_input_core() catches the error but it does not release the sk_buff,
which will result in a memory leak.
This issue was introduced in commit af3b5158b89d ("ipv6: sr: fix BUG due
to headroom too small after SRH push") and persists even after commit
7a3f5b0de364 ("netfilter: add netfilter hooks to SRv6 data plane"),
where the entire seg6_input() code was refactored to deal with netfilter
hooks.
The proposed patch addresses the identified memory leak by requiring the
seg6_input_core() function to release the sk_buff in the event that
skb_cow_head() fails.
Fixes: af3b5158b89d ("ipv6: sr: fix BUG due to headroom too small after SRH push")
Signed-off-by: Andrea Mayer <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Reviewed-by: David Ahern <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Stephen reported that he was unable to get the dsa_loop driver to get
probed, and the reason ended up being because he had CONFIG_FIXED_PHY=y
in his kernel configuration. As Masahiro explained it:
"obj-m += dsa/" means everything under dsa/ must be modular.
If there is a built-in object under dsa/ with CONFIG_NET_DSA=m,
you cannot do "obj-$(CONFIG_NET_DSA) += dsa/".
You need to change it back to "obj-y += dsa/".
This was the case here whereby CONFIG_NET_DSA=m, and so the
obj-$(CONFIG_FIXED_PHY) += dsa_loop_bdinfo.o rule is not executed and
the DSA loop mdio_board info structure is not registered with the
kernel, and eventually the device is simply not found.
To preserve the intention of the original commit of limiting the amount
of folder descending, conditionally descend into drivers/net/dsa when
CONFIG_NET_DSA is enabled.
Fixes: 227d72063fcc ("dsa: simplify Kconfig symbols and dependencies")
Reported-by: Stephen Langstaff <[email protected]>
Signed-off-by: Florian Fainelli <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Reviewed-by: Alexander Lobakin <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Commit 1a7d0890dd4a ("kprobe/ftrace: bail out if ftrace was killed")
introduced a bad K&R function definition, which we haven't accepted in a
long long time.
Gcc seems to let it slide, but clang notices with the appropriate error:
kernel/kprobes.c:1140:24: error: a function declaration without a prototype is deprecated in all >
1140 | void kprobe_ftrace_kill()
| ^
| void
but this commit was apparently never in linux-next before it was sent
upstream, so it didn't get the appropriate build test coverage.
Fixes: 1a7d0890dd4a kprobe/ftrace: bail out if ftrace was killed
Cc: Stephen Brennan <[email protected]>
Cc: Masami Hiramatsu (Google) <[email protected]>
Cc: Guo Ren <[email protected]>
Cc: Steven Rostedt (Google) <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Current release - regressions:
- virtio_net: fix missed error path rtnl_unlock after control queue
locking rework
Current release - new code bugs:
- bpf: fix KASAN slab-out-of-bounds in percpu_array_map_gen_lookup,
caused by missing nested map handling
- drv: dsa: correct initialization order for KSZ88x3 ports
Previous releases - regressions:
- af_packet: do not call packet_read_pending() from
tpacket_destruct_skb() fix performance regression
- ipv6: fix route deleting failure when metric equals 0, don't assume
0 means not set / default in this case
Previous releases - always broken:
- bridge: couple of syzbot-driven fixes"
* tag 'net-6.10-rc0' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (30 commits)
selftests: net: local_termination: annotate the expected failures
net: dsa: microchip: Correct initialization order for KSZ88x3 ports
MAINTAINERS: net: Update reviewers for TI's Ethernet drivers
dt-bindings: net: ti: Update maintainers list
l2tp: fix ICMP error handling for UDP-encap sockets
net: txgbe: fix to control VLAN strip
net: wangxun: match VLAN CTAG and STAG features
net: wangxun: fix to change Rx features
af_packet: do not call packet_read_pending() from tpacket_destruct_skb()
virtio_net: Fix missed rtnl_unlock
netrom: fix possible dead-lock in nr_rt_ioctl()
idpf: don't skip over ethtool tcp-data-split setting
dt-bindings: net: qcom: ethernet: Allow dma-coherent
bonding: fix oops during rmmod
net/ipv6: Fix route deleting failure when metric equals 0
selftests/net: reduce xfrm_policy test time
selftests/bpf: Adjust btf_dump test to reflect recent change in file_operations
selftests/bpf: Adjust test_access_variable_array after a kernel function name change
selftests/net/lib: no need to record ns name if it already exist
net: qrtr: ns: Fix module refcnt
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing tool updates from Steven Rostedt:
"Specific for timerlat:
- Improve the output of timerlat top by adding a missing \n, and by
avoiding printing color-formatting characters where they are
translated to regular characters.
- Improve timerlat auto-analysis output by replacing '\t' with spaces
to avoid copy-and-paste issues when reporting problems.
- Make the user-space (-u) option the default, as it is the most
complete test. Add a -k option to use the in-kernel workload.
- On timerlat top and hist, add a summary with the overall results.
For instance, the minimum value for all CPUs, the overall average
and the maximum value from all CPUs.
- timerlat hist was printing initial values (i.e., 0 as max, and ~0
as min) if the trace stopped before the first Ret-User event. This
problem was fixed by printing the " - " no value string to the
output if that was the case.
For all RTLA tools:
- Add a --warm-up <seconds> option, allowing the workload to run for
<seconds> before starting to collect results.
- Add a --trace-buffer-size option, allowing the user to set the
tracing buffer size for -t option. This option is mainly useful for
reducing the trace file. Now rtla depends on libtracefs >= 1.6.
- Fix the -t [trace_file] parsing, now it does not require the '='
before the option parameter, and better handles the multiple ways a
user can pass the trace_file.txt"
* tag 'trace-tools-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
rtla: Documentation: Fix -t, --trace
rtla: Fix -t\--trace[=file]
rtla/timerlat: Fix histogram report when a cpu count is 0
rtla: Add --trace-buffer-size option
rtla/timerlat: Make user-space threads the default
rtla: Add the --warm-up option
rtla/timerlat: Add a summary for hist mode
rtla/timerlat: Add a summary for top mode
rtla/timerlat: Use pretty formatting only on interactive tty
rtla/auto-analysis: Replace \t with spaces
rtla/timerlat: Simplify "no value" printing on top
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing user-event updates from Steven Rostedt:
- Minor update to the user_events interface
The ABI of creating a user event states that the fields are separated
by semicolons, and spaces should be ignored.
But the parsing expected at least one space to be there (which was
incorrect). Fix the reading of the string to handle fields separated
by semicolons but no space between them.
This does extend the API sightly as now "field;field" will now be
parsed and not cause an error. But it should not cause any regressions
as no logic should expect it to fail.
Note, that the logic that parses the event fields to create the
trace_event works with no spaces after the semi-colon. It is
the logic that tests against existing events that is inconsistent.
This causes registering an event without using spaces to succeed
if it doesn't exist, but makes the same call that tries to register
to the same event, but doesn't use spaces, fail.
* tag 'trace-user-events-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
selftests/user_events: Add non-spacing separator check
tracing/user_events: Fix non-spaced field matching
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing ring buffer updates from Steven Rostedt:
"Add ring_buffer memory mappings.
The tracing ring buffer was created based on being mostly used with
the splice system call. It is broken up into page ordered sub-buffers
and the reader swaps a new sub-buffer with an existing sub-buffer
that's part of the write buffer. It then has total access to the
swapped out sub-buffer and can do copyless movements of the memory
into other mediums (file system, network, etc).
The buffer is great for passing around the ring buffer contents in the
kernel, but is not so good for when the consumer is the user space
task itself.
A new interface is added that allows user space to memory map the ring
buffer. It will get all the write sub-buffers as well as reader
sub-buffer (that is not written to). It can send an ioctl to change
which sub-buffer is the new reader sub-buffer.
The ring buffer is read only to user space. It only needs to call the
ioctl when it is finished with a sub-buffer and needs a new sub-buffer
that the writer will not write over.
A self test program was also created for testing and can be used as an
example for the interface to user space. The libtracefs (external to
the kernel) also has code that interacts with this, although it is
disabled until the interface is in a official release. It can be
enabled by compiling the library with a special flag. This was used
for testing applications that perform better with the buffer being
mapped.
Memory mapped buffers have limitations. The main one is that it can
not be used with the snapshot logic. If the buffer is mapped,
snapshots will be disabled. If any logic is set to trigger snapshots
on a buffer, that buffer will not be allowed to be mapped"
* tag 'trace-ringbuffer-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
ring-buffer: Add cast to unsigned long addr passed to virt_to_page()
ring-buffer: Have mmapped ring buffer keep track of missed events
ring-buffer/selftest: Add ring-buffer mapping test
Documentation: tracing: Add ring-buffer mapping
tracing: Allow user-space mapping of the ring-buffer
ring-buffer: Introducing ring-buffer mapping functions
ring-buffer: Allocate sub-buffers with __GFP_COMP
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing updates from Steven Rostedt:
- Remove unused ftrace_direct_funcs variables
- Fix a possible NULL pointer dereference race in eventfs
- Update do_div() usage in trace event benchmark test
- Speedup direct function registration with asynchronous RCU callback.
The synchronization was done in the registration code and this caused
delays when registering direct callbacks. Move the freeing to a
call_rcu() that will prevent delaying of the registering.
- Replace simple_strtoul() usage with kstrtoul()
* tag 'trace-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
eventfs: Fix a possible null pointer dereference in eventfs_find_events()
ftrace: Fix possible use-after-free issue in ftrace_location()
ftrace: Remove unused global 'ftrace_direct_func_count'
ftrace: Remove unused list 'ftrace_direct_funcs'
tracing: Improve benchmark test performance by using do_div()
ftrace: Use asynchronous grace period for register_ftrace_direct()
ftrace: Replaces simple_strtoul in ftrace
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull probes updates from Masami Hiramatsu:
- tracing/probes: Add new pseudo-types %pd and %pD support for dumping
dentry name from 'struct dentry *' and file name from 'struct file *'
- uprobes performance optimizations:
- Speed up the BPF uprobe event by delaying the fetching of the
uprobe event arguments that are not used in BPF
- Avoid locking by speculatively checking whether uprobe event is
valid
- Reduce lock contention by using read/write_lock instead of
spinlock for uprobe list operation. This improved BPF uprobe
benchmark result 43% on average
- rethook: Remove non-fatal warning messages when tracing stack from
BPF and skip rcu_is_watching() validation in rethook if possible
- objpool: Optimize objpool (which is used by kretprobes and fprobe as
rethook backend storage) by inlining functions and avoid caching
nr_cpu_ids because it is a const value
- fprobe: Add entry/exit callbacks types (code cleanup)
- kprobes: Check ftrace was killed in kprobes if it uses ftrace
* tag 'probes-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
kprobe/ftrace: bail out if ftrace was killed
selftests/ftrace: Fix required features for VFS type test case
objpool: cache nr_possible_cpus() and avoid caching nr_cpu_ids
objpool: enable inlining objpool_push() and objpool_pop() operations
rethook: honor CONFIG_FTRACE_VALIDATE_RCU_IS_WATCHING in rethook_try_get()
ftrace: make extra rcu_is_watching() validation check optional
uprobes: reduce contention on uprobes_tree access
rethook: Remove warning messages printed for finding return address of a frame.
fprobe: Add entry/exit callbacks types
selftests/ftrace: add fprobe test cases for VFS type "%pd" and "%pD"
selftests/ftrace: add kprobe test cases for VFS type "%pd" and "%pD"
Documentation: tracing: add new type '%pd' and '%pD' for kprobe
tracing/probes: support '%pD' type for print struct file's name
tracing/probes: support '%pd' type for print struct dentry's name
uprobes: add speculative lockless system-wide uprobe filter check
uprobes: prepare uprobe args buffer lazily
uprobes: encapsulate preparation of uprobe args buffer
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull bootconfig updates from Masami Hiramatsu:
- Do not put unneeded quotes on the extra command line items which was
inserted from the bootconfig.
- Remove redundant spaces from the extra command line.
* tag 'bootconfig-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
init/main.c: Minor cleanup for the setup_command_line() function
init/main.c: Remove redundant space from saved_command_line
bootconfig: do not put quotes on cmdline items unless necessary
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sysctl/sysctl
Pull sysctl updates from Joel Granados:
- Remove sentinel elements from ctl_table structs in kernel/*
Removing sentinels in ctl_table arrays reduces the build time size
and runtime memory consumed by ~64 bytes per array. Removals for
net/, io_uring/, mm/, ipc/ and security/ are set to go into mainline
through their respective subsystems making the next release the most
likely place where the final series that removes the check for
proc_name == NULL will land.
This adds to removals already in arch/, drivers/ and fs/.
- Adjust ctl_table definitions and references to allow constification
- Remove unused ctl_table function arguments
- Move non-const elements from ctl_table to ctl_table_header
- Make ctl_table pointers const in ctl_table_root structure
Making the static ctl_table structs const will increase safety by
keeping the pointers to proc_handler functions in .rodata. Though no
ctl_tables where made const in this PR, the ground work for making
that possible has started with these changes sent by Thomas
Weißschuh.
* tag 'sysctl-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/sysctl/sysctl:
sysctl: drop now unnecessary out-of-bounds check
sysctl: move sysctl type to ctl_table_header
sysctl: drop sysctl_is_perm_empty_ctl_table
sysctl: treewide: constify argument ctl_table_root::permissions(table)
sysctl: treewide: drop unused argument ctl_table_root::set_ownership(table)
bpf: Remove the now superfluous sentinel elements from ctl_table array
delayacct: Remove the now superfluous sentinel elements from ctl_table array
kprobes: Remove the now superfluous sentinel elements from ctl_table array
printk: Remove the now superfluous sentinel elements from ctl_table array
scheduler: Remove the now superfluous sentinel elements from ctl_table array
seccomp: Remove the now superfluous sentinel elements from ctl_table array
timekeeping: Remove the now superfluous sentinel elements from ctl_table array
ftrace: Remove the now superfluous sentinel elements from ctl_table array
umh: Remove the now superfluous sentinel elements from ctl_table array
kernel misc: Remove the now superfluous sentinel elements from ctl_table array
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"DT Bindings:
- Convert samsung,exynos5-dp, atmel,lcdc, aspeed,ast2400-wdt bindings
to schemas
- Add bindings for Allwinner H616 NMI controller, Renesas r8a779g0
irqc, Renesas R-Car V4M TMU and CMT timers, Freescale S32G3
linflexuart, and Mediatek MT7988 XHCI
- Add 'reg' constraints on DSI and SPI display panels
- More dropping of unnecessary quotes in schemas
- Use full paths rather than relative paths in schema $refs
- Drop redundant storing of phandle for reserved memory
DT Core:
- Use scope based cleanups for kfree() and of_node_put()
- Track interrupt-map and power-supplies for fw_devlink
- Add buffer overflow check in of_modalias()
- Add and use __of_prop_free() helper for freeing struct property"
* tag 'devicetree-for-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (25 commits)
of: property: Add fw_devlink support for interrupt-map property
dt-bindings: display: panel: constrain 'reg' in DSI panels
dt-bindings: display: panel: constrain 'reg' in SPI panels
dt-bindings: display: samsung,ams495qa01: add missing SPI properties ref
dt-bindings: Use full path to other schemas
dt-bindings: PCI: qcom,pcie-sm8350: Drop redundant 'oneOf' sub-schema
of: module: add buffer overflow check in of_modalias()
dt-bindings: PCI: microchip: increase number of items in ranges property
dt-bindings: Drop unnecessary quotes on keys
dt-bindings: interrupt-controller: mediatek,mt6577-sysirq: Drop unnecessary quotes
of: property: Use scope based cleanup on port_node
of: reserved_mem: Remove the use of phandle from the reserved_mem APIs
of: property: fw_devlink: Add support for "power-supplies" binding
dt-bindings: watchdog: aspeed,ast2400-wdt: Convert to DT schema
dt-bindings: irq: sun7i-nmi: Add binding for the H616 NMI controller
dt-bindings: interrupt-controller: renesas,irqc: Add r8a779g0 support
dt-bindings: timer: renesas,tmu: Add R-Car V4M support
dt-bindings: timer: renesas,cmt: Add R-Car V4M support
of: Use scope based of_node_put() cleanups
of: Use scope based kfree() cleanups
...
|
|
Vladimir said when adding this test:
The bridge driver fares particularly badly [...] mainly because
it does not implement IFF_UNICAST_FLT.
See commit 90b9566aa5cd ("selftests: forwarding: add a test for
local_termination.sh").
We don't want to hide the known gaps, but having a test which
always fails prevents us from catching regressions. Report
the cases we know may fail as XFAIL.
Reviewed-by: Simon Horman <[email protected]>
Reviewed-by: Hangbin Liu <[email protected]>
Reviewed-by: Petr Machata <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Adjust the initialization sequence of KSZ88x3 switches to enable
802.1p priority control on Port 2 before configuring Port 1. This
change ensures the apptrust functionality on Port 1 operates
correctly, as it depends on the priority settings of Port 2. The
prior initialization sequence incorrectly configured Port 1 first,
which could lead to functional discrepancies.
Fixes: a1ea57710c9d ("net: dsa: microchip: dcb: add special handling for KSZ88X3 family")
Signed-off-by: Oleksij Rempel <[email protected]>
Reviewed-by: Hariprasad Kelam <[email protected]>
Acked-by: Arun Ramadoss <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Remove myself as reviewer for TI's ethernet drivers
Signed-off-by: Ravi Gunasekaran <[email protected]>
Reviewed-by: Roger Quadros <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Update the list with the current maintainers of TI's CPSW ethernet
peripheral.
Signed-off-by: Ravi Gunasekaran <[email protected]>
Acked-by: Conor Dooley <[email protected]>
Acked-by: Roger Quadros <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Since commit a36e185e8c85
("udp: Handle ICMP errors for tunnels with same destination port on both endpoints")
UDP's handling of ICMP errors has allowed for UDP-encap tunnels to
determine socket associations in scenarios where the UDP hash lookup
could not.
Subsequently, commit d26796ae58940
("udp: check udp sock encap_type in __udp_lib_err")
subtly tweaked the approach such that UDP ICMP error handling would be
skipped for any UDP socket which has encapsulation enabled.
In the case of L2TP tunnel sockets using UDP-encap, this latter
modification effectively broke ICMP error reporting for the L2TP
control plane.
To a degree this isn't catastrophic inasmuch as the L2TP control
protocol defines a reliable transport on top of the underlying packet
switching network which will eventually detect errors and time out.
However, paying attention to the ICMP error reporting allows for more
timely detection of errors in L2TP userspace, and aids in debugging
connectivity issues.
Reinstate ICMP error handling for UDP encap L2TP tunnels:
* implement struct udp_tunnel_sock_cfg .encap_err_rcv in order to allow
the L2TP code to handle ICMP errors;
* only implement error-handling for tunnels which have a managed
socket: unmanaged tunnels using a kernel socket have no userspace to
report errors back to;
* flag the error on the socket, which allows for userspace to get an
error such as -ECONNREFUSED back from sendmsg/recvmsg;
* pass the error into ip[v6]_icmp_error() which allows for userspace to
get extended error information via. MSG_ERRQUEUE.
Fixes: d26796ae5894 ("udp: check udp sock encap_type in __udp_lib_err")
Signed-off-by: Tom Parkin <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc updates from Helge Deller:
- define sigset_t in parisc uapi header to fix build of util-linux
- define HAVE_ARCH_HUGETLB_UNMAPPED_AREA to avoid compiler warning
- drop unused 'exc_reg' struct in math-emu code
* tag 'parisc-for-6.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Define HAVE_ARCH_HUGETLB_UNMAPPED_AREA
parisc/math-emu: Remove unused struct 'exc_reg'
parisc: Define sigset_t in parisc uapi header
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- Enable BPF Kernel Functions (kfuncs) in the powerpc BPF JIT.
- Allow per-process DEXCR (Dynamic Execution Control Register) settings
via prctl, notably NPHIE which controls hashst/hashchk for ROP
protection.
- Install powerpc selftests in sub-directories. Note this changes the
way run_kselftest.sh needs to be invoked for powerpc selftests.
- Change fadump (Firmware Assisted Dump) to better handle memory
add/remove.
- Add support for passing additional parameters to the fadump kernel.
- Add support for updating the kdump image on CPU/memory add/remove
events.
- Other small features, cleanups and fixes.
Thanks to Andrew Donnellan, Andy Shevchenko, Aneesh Kumar K.V, Arnd
Bergmann, Benjamin Gray, Bjorn Helgaas, Christian Zigotzky, Christophe
Jaillet, Christophe Leroy, Colin Ian King, Cédric Le Goater, Dr. David
Alan Gilbert, Erhard Furtner, Frank Li, GUO Zihua, Ganesh Goudar, Geoff
Levand, Ghanshyam Agrawal, Greg Kurz, Hari Bathini, Joel Stanley, Justin
Stitt, Kunwu Chan, Li Yang, Lidong Zhong, Madhavan Srinivasan, Mahesh
Salgaonkar, Masahiro Yamada, Matthias Schiffer, Naresh Kamboju, Nathan
Chancellor, Nathan Lynch, Naveen N Rao, Nicholas Miehlbradt, Ran Wang,
Randy Dunlap, Ritesh Harjani, Sachin Sant, Shirisha Ganta, Shrikanth
Hegde, Sourabh Jain, Stephen Rothwell, sundar, Thorsten Blum, Vaibhav
Jain, Xiaowei Bao, Yang Li, and Zhao Chenhui.
* tag 'powerpc-6.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (85 commits)
powerpc/fadump: Fix section mismatch warning
powerpc/85xx: fix compile error without CONFIG_CRASH_DUMP
powerpc/fadump: update documentation about bootargs_append
powerpc/fadump: pass additional parameters when fadump is active
powerpc/fadump: setup additional parameters for dump capture kernel
powerpc/pseries/fadump: add support for multiple boot memory regions
selftests/powerpc/dexcr: Fix spelling mistake "predicition" -> "prediction"
KVM: PPC: Book3S HV nestedv2: Fix an error handling path in gs_msg_ops_kvmhv_nestedv2_config_fill_info()
KVM: PPC: Fix documentation for ppc mmu caps
KVM: PPC: code cleanup for kvmppc_book3s_irqprio_deliver
KVM: PPC: Book3S HV nestedv2: Cancel pending DEC exception
powerpc/xmon: Check cpu id in commands "c#", "dp#" and "dx#"
powerpc/code-patching: Use dedicated memory routines for patching
powerpc/code-patching: Test patch_instructions() during boot
powerpc64/kasan: Pass virtual addresses to kasan_init_phys_region()
powerpc: rename SPRN_HID2 define to SPRN_HID2_750FX
powerpc: Fix typos
powerpc/eeh: Fix spelling of the word "auxillary" and update comment
macintosh/ams: Fix unused variable warning
powerpc/Makefile: Remove bits related to the previous use of -mcmodel=large
...
|
|
Pull ARM updates from Russell King:
- Updates to AMBA bus subsystem to drop .owner struct device_driver
initialisations, moving that to code instead.
- Add LPAE privileged-access-never support
- Add support for Clang CFI
- clkdev: report over-sized device or connection strings
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rmk/linux: (36 commits)
ARM: 9398/1: Fix userspace enter on LPAE with CC_OPTIMIZE_FOR_SIZE=y
clkdev: report over-sized strings when creating clkdev entries
ARM: 9393/1: mm: Use conditionals for CFI branches
ARM: 9392/2: Support CLANG CFI
ARM: 9391/2: hw_breakpoint: Handle CFI breakpoints
ARM: 9390/2: lib: Annotate loop delay instructions for CFI
ARM: 9389/2: mm: Define prototypes for all per-processor calls
ARM: 9388/2: mm: Type-annotate all per-processor assembly routines
ARM: 9387/2: mm: Rewrite cacheflush vtables in CFI safe C
ARM: 9386/2: mm: Use symbol alias for cache functions
ARM: 9385/2: mm: Type-annotate all cache assembly routines
ARM: 9384/2: mm: Make tlbflush routines CFI safe
ARM: 9382/1: ftrace: Define ftrace_stub_graph
ARM: 9358/2: Implement PAN for LPAE by TTBR0 page table walks disablement
ARM: 9357/2: Reduce the number of #ifdef CONFIG_CPU_SW_DOMAIN_PAN
ARM: 9356/2: Move asm statements accessing TTBCR into C functions
ARM: 9355/2: Add TTBCR_* definitions to pgtable-3level-hwdef.h
ARM: 9379/1: coresight: tpda: drop owner assignment
ARM: 9378/1: coresight: etm4x: drop owner assignment
ARM: 9377/1: hwrng: nomadik: drop owner assignment
...
|
|
Jiawen Wu says:
====================
Wangxun fixes
Fixed some bugs when using ethtool to operate network devices.
v4 -> v5:
- Simplify if...else... to fix features.
v3 -> v4:
- Require both ctag and stag to be enabled or disabled.
v2 -> v3:
- Drop the first patch.
v1 -> v2:
- Factor out the same code.
- Remove statistics printing with more than 64 queues.
- Detail the commit logs to describe issues.
- Remove reset flag check in wx_update_stats().
- Change to set VLAN CTAG and STAG to be consistent.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
When VLAN tag strip is changed to enable or disable, the hardware requires
the Rx ring to be in a disabled state, otherwise the feature cannot be
changed.
Fixes: f3b03c655f67 ("net: wangxun: Implement vlan add and kill functions")
Signed-off-by: Jiawen Wu <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Hardware requires VLAN CTAG and STAG configuration always matches. And
whether VLAN CTAG or STAG changes, the configuration needs to be changed
as well.
Fixes: 6670f1ece2c8 ("net: txgbe: Add netdev features support")
Signed-off-by: Jiawen Wu <[email protected]>
Reviewed-by: Sai Krishna <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Fix the issue where some Rx features cannot be changed.
When using ethtool -K to turn off rx offload, it returns error and
displays "Could not change any device features". And netdev->features
is not assigned a new value to actually configure the hardware.
Fixes: 6dbedcffcf54 ("net: libwx: Implement xx_set_features ops")
Signed-off-by: Jiawen Wu <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
trafgen performance considerably sank on hosts with many cores
after the blamed commit.
packet_read_pending() is very expensive, and calling it
in af_packet fast path defeats Daniel intent in commit
b013840810c2 ("packet: use percpu mmap tx frame pending refcount")
tpacket_destruct_skb() makes room for one packet, we can immediately
wakeup a producer, no need to completely drain the tx ring.
Fixes: 89ed5b519004 ("af_packet: Block execution of tasks waiting for transmit to complete in AF_PACKET")
Signed-off-by: Eric Dumazet <[email protected]>
Cc: Neil Horman <[email protected]>
Cc: Daniel Borkmann <[email protected]>
Reviewed-by: Willem de Bruijn <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
The rtnl_lock would stay locked if allocating promisc_allmulti failed.
Also changed the allocation to GFP_KERNEL.
Fixes: ff7c7d9f5261 ("virtio_net: Remove command data from control_buf")
Reported-by: Eric Dumazet <[email protected]>
Link: https://lore.kernel.org/netdev/CANn89iLazVaUCvhPm6RPJJ0owra_oFnx7Fhc8d60gV-65ad3WQ@mail.gmail.com/
Signed-off-by: Daniel Jurgens <[email protected]>
Reviewed-by: Brett Creeley <[email protected]>
Reviewed-by: Eric Dumazet <[email protected]>
Acked-by: Michael S. Tsirkin <[email protected]>
Acked-by: Jason Wang <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
syzbot loves netrom, and found a possible deadlock in nr_rt_ioctl [1]
Make sure we always acquire nr_node_list_lock before nr_node_lock(nr_node)
[1]
WARNING: possible circular locking dependency detected
6.9.0-rc7-syzkaller-02147-g654de42f3fc6 #0 Not tainted
------------------------------------------------------
syz-executor350/5129 is trying to acquire lock:
ffff8880186e2070 (&nr_node->node_lock){+...}-{2:2}, at: spin_lock_bh include/linux/spinlock.h:356 [inline]
ffff8880186e2070 (&nr_node->node_lock){+...}-{2:2}, at: nr_node_lock include/net/netrom.h:152 [inline]
ffff8880186e2070 (&nr_node->node_lock){+...}-{2:2}, at: nr_dec_obs net/netrom/nr_route.c:464 [inline]
ffff8880186e2070 (&nr_node->node_lock){+...}-{2:2}, at: nr_rt_ioctl+0x1bb/0x1090 net/netrom/nr_route.c:697
but task is already holding lock:
ffffffff8f7053b8 (nr_node_list_lock){+...}-{2:2}, at: spin_lock_bh include/linux/spinlock.h:356 [inline]
ffffffff8f7053b8 (nr_node_list_lock){+...}-{2:2}, at: nr_dec_obs net/netrom/nr_route.c:462 [inline]
ffffffff8f7053b8 (nr_node_list_lock){+...}-{2:2}, at: nr_rt_ioctl+0x10a/0x1090 net/netrom/nr_route.c:697
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (nr_node_list_lock){+...}-{2:2}:
lock_acquire+0x1ed/0x550 kernel/locking/lockdep.c:5754
__raw_spin_lock_bh include/linux/spinlock_api_smp.h:126 [inline]
_raw_spin_lock_bh+0x35/0x50 kernel/locking/spinlock.c:178
spin_lock_bh include/linux/spinlock.h:356 [inline]
nr_remove_node net/netrom/nr_route.c:299 [inline]
nr_del_node+0x4b4/0x820 net/netrom/nr_route.c:355
nr_rt_ioctl+0xa95/0x1090 net/netrom/nr_route.c:683
sock_do_ioctl+0x158/0x460 net/socket.c:1222
sock_ioctl+0x629/0x8e0 net/socket.c:1341
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:904 [inline]
__se_sys_ioctl+0xfc/0x170 fs/ioctl.c:890
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xf5/0x240 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
-> #0 (&nr_node->node_lock){+...}-{2:2}:
check_prev_add kernel/locking/lockdep.c:3134 [inline]
check_prevs_add kernel/locking/lockdep.c:3253 [inline]
validate_chain+0x18cb/0x58e0 kernel/locking/lockdep.c:3869
__lock_acquire+0x1346/0x1fd0 kernel/locking/lockdep.c:5137
lock_acquire+0x1ed/0x550 kernel/locking/lockdep.c:5754
__raw_spin_lock_bh include/linux/spinlock_api_smp.h:126 [inline]
_raw_spin_lock_bh+0x35/0x50 kernel/locking/spinlock.c:178
spin_lock_bh include/linux/spinlock.h:356 [inline]
nr_node_lock include/net/netrom.h:152 [inline]
nr_dec_obs net/netrom/nr_route.c:464 [inline]
nr_rt_ioctl+0x1bb/0x1090 net/netrom/nr_route.c:697
sock_do_ioctl+0x158/0x460 net/socket.c:1222
sock_ioctl+0x629/0x8e0 net/socket.c:1341
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:904 [inline]
__se_sys_ioctl+0xfc/0x170 fs/ioctl.c:890
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xf5/0x240 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(nr_node_list_lock);
lock(&nr_node->node_lock);
lock(nr_node_list_lock);
lock(&nr_node->node_lock);
*** DEADLOCK ***
1 lock held by syz-executor350/5129:
#0: ffffffff8f7053b8 (nr_node_list_lock){+...}-{2:2}, at: spin_lock_bh include/linux/spinlock.h:356 [inline]
#0: ffffffff8f7053b8 (nr_node_list_lock){+...}-{2:2}, at: nr_dec_obs net/netrom/nr_route.c:462 [inline]
#0: ffffffff8f7053b8 (nr_node_list_lock){+...}-{2:2}, at: nr_rt_ioctl+0x10a/0x1090 net/netrom/nr_route.c:697
stack backtrace:
CPU: 0 PID: 5129 Comm: syz-executor350 Not tainted 6.9.0-rc7-syzkaller-02147-g654de42f3fc6 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 04/02/2024
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x241/0x360 lib/dump_stack.c:114
check_noncircular+0x36a/0x4a0 kernel/locking/lockdep.c:2187
check_prev_add kernel/locking/lockdep.c:3134 [inline]
check_prevs_add kernel/locking/lockdep.c:3253 [inline]
validate_chain+0x18cb/0x58e0 kernel/locking/lockdep.c:3869
__lock_acquire+0x1346/0x1fd0 kernel/locking/lockdep.c:5137
lock_acquire+0x1ed/0x550 kernel/locking/lockdep.c:5754
__raw_spin_lock_bh include/linux/spinlock_api_smp.h:126 [inline]
_raw_spin_lock_bh+0x35/0x50 kernel/locking/spinlock.c:178
spin_lock_bh include/linux/spinlock.h:356 [inline]
nr_node_lock include/net/netrom.h:152 [inline]
nr_dec_obs net/netrom/nr_route.c:464 [inline]
nr_rt_ioctl+0x1bb/0x1090 net/netrom/nr_route.c:697
sock_do_ioctl+0x158/0x460 net/socket.c:1222
sock_ioctl+0x629/0x8e0 net/socket.c:1341
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:904 [inline]
__se_sys_ioctl+0xfc/0x170 fs/ioctl.c:890
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xf5/0x240 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: syzbot <[email protected]>
Signed-off-by: Eric Dumazet <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Disabling tcp-data-split on idpf silently fails:
# ethtool -G $NETDEV tcp-data-split off
# ethtool -g $NETDEV | grep 'TCP data split'
TCP data split: on
But it works if you also change 'tx' or 'rx':
# ethtool -G $NETDEV tcp-data-split off tx 256
# ethtool -g $NETDEV | grep 'TCP data split'
TCP data split: off
The bug is in idpf_set_ringparam, where it takes a shortcut out if the
TX and RX sizes are not changing. Fix it by checking also if the
tcp-data-split setting remains unchanged. Only then can the soft reset
be skipped.
Fixes: 9b1aa3ef2328 ("idpf: add get/set for Ethtool's header split ringparam")
Reported-by: Xu Du <[email protected]>
Closes: https://issues.redhat.com/browse/RHEL-36182
Signed-off-by: Michal Schmidt <[email protected]>
Reviewed-by: Alexander Lobakin <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
On SA8775P, Ethernet DMA controller is coherent with the CPU.
allow specifying that.
Signed-off-by: Sagar Cheluvegowda <[email protected]>
Acked-by: Krzysztof Kozlowski <[email protected]>
Link: https://lore.kernel.org/r/20240514-mark_ethernet_devices_dma_coherent-v4-2-04e1198858c5@quicinc.com
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
"rmmod bonding" causes an oops ever since commit cc317ea3d927 ("bonding:
remove redundant NULL check in debugfs function"). Here are the relevant
functions being called:
bonding_exit()
bond_destroy_debugfs()
debugfs_remove_recursive(bonding_debug_root);
bonding_debug_root = NULL; <--------- SET TO NULL HERE
bond_netlink_fini()
rtnl_link_unregister()
__rtnl_link_unregister()
unregister_netdevice_many_notify()
bond_uninit()
bond_debug_unregister()
(commit removed check for bonding_debug_root == NULL)
debugfs_remove()
simple_recursive_removal()
down_write() -> OOPS
However, reverting the bad commit does not solve the problem completely
because the original code contains a race that could cause the same
oops, although it was much less likely to be triggered unintentionally:
CPU1
rmmod bonding
bonding_exit()
bond_destroy_debugfs()
debugfs_remove_recursive(bonding_debug_root);
CPU2
echo -bond0 > /sys/class/net/bonding_masters
bond_uninit()
bond_debug_unregister()
if (!bonding_debug_root)
CPU1
bonding_debug_root = NULL;
So do NOT revert the bad commit (since the removed checks were racy
anyway), and instead change the order of actions taken during module
removal. The same oops can also happen if there is an error during
module init, so apply the same fix there.
Fixes: cc317ea3d927 ("bonding: remove redundant NULL check in debugfs function")
Cc: [email protected]
Signed-off-by: Tony Battersby <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Acked-by: Jay Vosburgh <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Problem
=========
After commit 67f695134703 ("ipv6: Move setting default metric for routes"),
we noticed that the logic of assigning the default value of fc_metirc
changed in the ioctl process. That is, when users use ioctl(fd, SIOCADDRT,
rt) with a non-zero metric to add a route, then they may fail to delete a
route with passing in a metric value of 0 to the kernel by ioctl(fd,
SIOCDELRT, rt). But iproute can succeed in deleting it.
As a reference, when using iproute tools by netlink to delete routes with
a metric parameter equals 0, like the command as follows:
ip -6 route del fe80::/64 via fe81::5054:ff:fe11:3451 dev eth0 metric 0
the user can still succeed in deleting the route entry with the smallest
metric.
Root Reason
===========
After commit 67f695134703 ("ipv6: Move setting default metric for routes"),
When ioctl() pass in SIOCDELRT with a zero metric, rtmsg_to_fib6_config()
will set a defalut value (1024) to cfg->fc_metric in kernel, and in
ip6_route_del() and the line 4074 at net/ipv3/route.c, it will check by
if (cfg->fc_metric && cfg->fc_metric != rt->fib6_metric)
continue;
and the condition is true and skip the later procedure (deleting route)
because cfg->fc_metric != rt->fib6_metric. But before that commit,
cfg->fc_metric is still zero there, so the condition is false and it
will do the following procedure (deleting).
Solution
========
In order to keep a consistent behaviour across netlink() and ioctl(), we
should allow to delete a route with a metric value of 0. So we only do
the default setting of fc_metric in route adding.
CC: [email protected] # 5.4+
Fixes: 67f695134703 ("ipv6: Move setting default metric for routes")
Co-developed-by: Fan Yu <[email protected]>
Signed-off-by: Fan Yu <[email protected]>
Signed-off-by: xu xin <[email protected]>
Reviewed-by: David Ahern <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
The check_random_order test add/get plenty of xfrm rules, which consume
a lot time on debug kernel and always TIMEOUT. Let's reduce the test
loop and see if it works.
Signed-off-by: Hangbin Liu <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf
Daniel Borkmann says:
====================
pull-request: bpf 2024-05-17
We've added 7 non-merge commits during the last 2 day(s) which contain
a total of 8 files changed, 20 insertions(+), 9 deletions(-).
The main changes are:
1) Fix KASAN slab-out-of-bounds in percpu_array_map_gen_lookup and add
BPF selftests to cover this case, from Andrii Nakryiko.
(Report https://lore.kernel.org/bpf/[email protected]/)
2) Fix two BPF selftests to adjust for kernel changes after fast-forwarding
Linus' tree to make BPF CI all green again, from Martin KaFai Lau.
3) Fix libbpf feature detectors when using token_fd by adjusting the
attribute size for memset to cover the former, also from Andrii Nakryiko.
4) Fix the description of 'src' in ALU instructions for the BPF ISA
standardization doc, from Puranjay Mohan.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
selftests/bpf: Adjust btf_dump test to reflect recent change in file_operations
selftests/bpf: Adjust test_access_variable_array after a kernel function name change
selftests/bpf: add more variations of map-in-map situations
bpf: save extended inner map info for percpu array maps as well
MAINTAINERS: Update ARM64 BPF JIT maintainer
bpf, docs: Fix the description of 'src' in ALU instructions
libbpf: fix feature detectors when using token_fd
====================
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
The btf_dump test fails:
test_btf_dump_struct_data:FAIL:file_operations unexpected file_operations: actual '(struct file_operations){
.owner = (struct module *)0xffffffffffffffff,
.fop_flags = (fop_flags_t)4294967295,
.llseek = (loff_t (*)(struct f' != expected '(struct file_operations){
.owner = (struct module *)0xffffffffffffffff,
.llseek = (loff_t (*)(struct file *, loff_t, int))0xffffffffffffffff,'
The "fop_flags" is a recent addition to the struct file_operations in
commit 210a03c9d51a ("fs: claw back a few FMODE_* bits")
This patch changes the test_btf_dump_struct_data() to reflect
this change.
Signed-off-by: Martin KaFai Lau <[email protected]>
Signed-off-by: Daniel Borkmann <[email protected]>
Reviewed-by: Alan Maguire <[email protected]>
Link: https://lore.kernel.org/bpf/[email protected]
|
|
name change
After commit 4c3e509ea9f2 ("sched/balancing: Rename load_balance() => sched_balance_rq()"),
the load_balance kernel function is renamed to sched_balance_rq.
This patch adjusts the fentry program in test_access_variable_array.c
to reflect this kernel function name change.
Signed-off-by: Martin KaFai Lau <[email protected]>
Signed-off-by: Daniel Borkmann <[email protected]>
Acked-by: Daniel Borkmann <[email protected]>
Link: https://lore.kernel.org/bpf/[email protected]
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver updates from Hans de Goede:
- New drivers/platform/arm64 directory for arm64 embedded-controller
drivers
- New drivers:
- Acer Aspire 1 embedded controllers (for arm64 models)
- ACPI quickstart PNP0C32 buttons
- Dell All-In-One backlight support (dell-uart-backlight)
- Lenovo WMI camera buttons
- Lenovo Yoga Tablet 2 Pro 1380F/L fast charging
- MeeGoPad ANX7428 Type-C Cross Switch (power sequencing only)
- MSI WMI sensors (fan speed sensors only for now)
- Asus WMI:
- 2024 ROG Mini-LED support
- MCU powersave support
- Vivobook GPU MUX support
- Misc. other improvements
- Ideapad laptop:
- Export FnLock LED as LED class device
- Switch platform profiles using thermal management key
- Intel drivers:
- IFS: various improvements
- PMC: Lunar Lake support
- SDSI: various improvements
- TPMI/ISST: various improvements
- tools: intel-speed-select: various improvements
- MS Surface drivers:
- Fan profile switching support
- Surface Pro thermal sensors support
- ThinkPad ACPI:
- Reworked hotkey support to use sparse keymaps
- Add support for new trackpoint-doubletap, Fn+N and Fn+G hotkeys
- WMI core:
- New WMI driver development guide
- x86 Android tablets:
- Lenovo Yoga Tablet 2 Pro 1380F/L support
- Xiaomi MiPad 2 status LED and bezel touch buttons backlight
support
- Miscellaneous cleanups / fixes / improvements
* tag 'platform-drivers-x86-v6.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (128 commits)
platform/x86: Add new MeeGoPad ANX7428 Type-C Cross Switch driver
devm-helpers: Fix a misspelled cancellation in the comments
tools arch x86: Add dell-uart-backlight-emulator
platform/x86: Add new Dell UART backlight driver
platform/x86: x86-android-tablets: Create LED device for Xiaomi Pad 2 bottom bezel touch buttons
platform/x86: x86-android-tablets: Xiaomi pad2 RGB LED fwnode updates
platform/x86: x86-android-tablets: Pass struct device to init()
platform/x86/amd: pmc: Add new ACPI ID AMDI000B
platform/x86/amd: pmf: Add new ACPI ID AMDI0105
platform/x86: p2sb: Don't init until unassigned resources have been assigned
platform/surface: aggregator: Log critical errors during SAM probing
platform/x86: ISST: Support SST-BF and SST-TF per level
platform/x86/fujitsu-laptop: Replace sprintf() with sysfs_emit()
tools/power/x86/intel-speed-select: v1.19 release
tools/power/x86/intel-speed-select: Display CPU as None for -1
tools/power/x86/intel-speed-select: SST BF/TF support per level
tools/power/x86/intel-speed-select: Increase number of CPUs displayed
tools/power/x86/intel-speed-select: Present all TRL levels for turbo-freq
tools/power/x86/intel-speed-select: Fix display for unsupported levels
tools/power/x86/intel-speed-select: Support multiple dies
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"MTD:
- Simon Glass wanted to support binman's output properties in order
to check their validity using the binding checks and proposed
changes with the missing properties as well as a binman compatible.
- Krzysztof Kozlowski on his side shared a new yaml for describing
Samsung's OneNAND interface.
- The interface with NVMEM has also been slightly improved/fixed,
especially now that OTP are also supported in the NAND subsystem.
- Along with these changes, small cleanups have also been contributed
around ID tables, structure sizes, arithmetic checks and comments.
Raw NAND subsystem:
- Two small fixes, one in the Hynix vendor code for properly
returning an error which might have been ignored and another in the
Davinci driver to properly synchronize the controller with the gpio
domain.
SPI NOR subsystem:
- SPI NOR now uses div_u64() instead of div64_u64() in places where
the divisor is 32 bits. Many 32 bit architectures can optimize this
variant better than a full 64 bit divide"
* tag 'mtd/for-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: spi-nor: replace unnecessary div64_u64() with div_u64()
mtd: mchp23k256: drop unneeded MODULE_ALIAS
dt-bindings: mtd: fixed-partition: Add binman compatibles
dt-bindings: mtd: fixed-partitions: Add alignment properties
mtd: maps: sa1100-flash: Prefer struct_size over open coded arithmetic
mtd: core: Align comment with an action in mtd_otp_nvmem_add()
mtd: rawnand: hynix: fixed typo
mtd: rawnand: davinci: Add dummy read after sending command
mtd: partitions: redboot: Added conversion of operands to a larger type
dt-bindings: mtd: Add Samsung S5Pv210 OneNAND
mtd: core: Don't fail mtd_otp_nvmem_add() if OTP is unsupported
mtd: core: Report error if first mtd_otp_size() call fails in mtd_otp_nvmem_add()
|
|
Pull MMC updates from Ulf Hansson:
"MMC core:
- Increase the timeout period of the ACMD41 command
- Add card entry for quirks to debugfs
- Add mmc_gpiod_set_cd_config() function
- Store owner from SDIO modules with sdio_register_driver()
MMC host:
- atmel-mci: Some cleanups and a switch to use dev_err_probe()
- renesas_sdhi:
- Add support for RZ/G2L, RZ/G3S and RZ/V2M variants
- Set the SDBUF after reset
- sdhci: Add support for "Tuning Error" interrupts
- sdhci-acpi:
- Add quirk to enable pull-up on the card-detect GPIO on Asus
T100TA
- Disable write protect detection on Toshiba WT10-A
- Fix Lenovo Yoga Tablet 2 Pro 1380 sdcard slot not working
- sdhci_am654:
- Re-work and fix the tuning support for multiple speed-modes
- Add tuning algorithm for delay chain
- sdhci-esdhc-imx: Add NXP S32G3 support
- sdhci-of-dwcmshc:
- Add tuning support for Sophgo CV1800B and SG200X
- Implement SDHCI CQE support
- sdhci-pci-gli: Use the proper pci_set_power_state() instead of
PMCSR writes"
MEMSTICK:
- Convert a couple of drivers to use the ->remove_new() callback"
* tag 'mmc-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (59 commits)
mmc: renesas_sdhi: Add compatible string for RZ/G2L family, RZ/G3S, and RZ/V2M SoCs
dt-bindings: mmc: renesas,sdhi: Document RZ/G2L family compatibility
dt-bindings: mmc: renesas,sdhi: Group single const value items into an enum list
mmc: renesas_sdhi: Set the SDBUF after reset
mmc: core: Increase the timeout period of the ACMD41 command
mmc: core: Convert to use __mmc_poll_for_busy() SD_APP_OP_COND too
mmc: atmel-mci: Switch to use dev_err_probe()
mmc: atmel-mci: Incapsulate used to be a platform data into host structure
mmc: atmel-mci: Replace platform device pointer by generic one
mmc: atmel-mci: Use temporary variable for struct device
mmc: atmel-mci: Get rid of platform data leftovers
mmc: sdhci-of-dwcmshc: Add tuning support for Sophgo CV1800B and SG200X
mmc: sdhci-of-dwcmshc: Remove useless "&" of th1520_execute_tuning
mmc: sdhci-s3c: Choose sdhci_ops based on variant
mmc: sdhci_am654: Constify struct sdhci_ops
mmc: sdhci-sprd: Constify struct sdhci_ops
mmc: sdhci-omap: Constify struct sdhci_ops
mmc: sdhci-esdhc-mcf: Constify struct sdhci_ops
mmc: slot-gpio: Use irq_handler_t type
mmc: sdhci-acpi: Add quirk to enable pull-up on the card-detect GPIO on Asus T100TA
...
|