| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
hci_send_cmd_sync first sends skb and then tries to clone it. However,
the driver may have already freed the skb at that point.
Fix by cloning the sent_cmd cloned just above, instead of the original.
Log:
================================================================
BUG: KASAN: slab-use-after-free in __copy_skb_header+0x1a/0x240
...
Call Trace: ..
__skb_clone+0x59/0x2c0
hci_cmd_work+0x3b3/0x3d0 [bluetooth]
process_one_work+0x459/0x900
...
Allocated by task 129: ...
__alloc_skb+0x1ae/0x220
__hci_cmd_sync_sk+0x44c/0x7a0 [bluetooth]
__hci_cmd_sync_status+0x24/0xb0 [bluetooth]
set_cig_params_sync+0x778/0x7d0 [bluetooth]
...
Freed by task 0: ...
kmem_cache_free+0x157/0x3c0
__usb_hcd_giveback_urb+0x11e/0x1e0
usb_giveback_urb_bh+0x1ad/0x2a0
tasklet_action_common.isra.0+0x259/0x4a0
__do_softirq+0x15b/0x5a7
================================================================
Fixes: 2615fd9a7c25 ("Bluetooth: hci_sync: Fix overwriting request callback")
Signed-off-by: Pauli Virtanen <[email protected]>
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
Attemting to do sock_lock on .recvmsg may cause a deadlock as shown
bellow, so instead of using sock_sock this uses sk_receive_queue.lock
on bt_sock_ioctl to avoid the UAF:
INFO: task kworker/u9:1:121 blocked for more than 30 seconds.
Not tainted 6.7.6-lemon #183
Workqueue: hci0 hci_rx_work
Call Trace:
<TASK>
__schedule+0x37d/0xa00
schedule+0x32/0xe0
__lock_sock+0x68/0xa0
? __pfx_autoremove_wake_function+0x10/0x10
lock_sock_nested+0x43/0x50
l2cap_sock_recv_cb+0x21/0xa0
l2cap_recv_frame+0x55b/0x30a0
? psi_task_switch+0xeb/0x270
? finish_task_switch.isra.0+0x93/0x2a0
hci_rx_work+0x33a/0x3f0
process_one_work+0x13a/0x2f0
worker_thread+0x2f0/0x410
? __pfx_worker_thread+0x10/0x10
kthread+0xe0/0x110
? __pfx_kthread+0x10/0x10
ret_from_fork+0x2c/0x50
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1b/0x30
</TASK>
Fixes: 2e07e8348ea4 ("Bluetooth: af_bluetooth: Fix Use-After-Free in bt_sock_recvmsg")
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
This fixes attempting to access past ethhdr.h_source, although it seems
intentional to copy also the contents of h_proto this triggers
out-of-bound access problems with the likes of static analyzer, so this
instead just copy ETH_ALEN and then proceed to use put_unaligned to copy
h_proto separetely.
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
This checks if CONFIG_DEV_COREDUMP is enabled before attempting to clone
the skb and also make sure btmtk_process_coredump frees the skb passed
following the same logic.
Fixes: 0b7015132878 ("Bluetooth: btusb: mediatek: add MediaTek devcoredump support")
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
Fix leaking buffer allocated to send MSFT_OP_LE_MONITOR_ADVERTISEMENT.
Fixes: 9e14606d8f38 ("Bluetooth: msft: Extended monitor tracking by address filter")
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
struct hci_dev_info has a fixed size name[8] field so in the event that
hdev->name is bigger than that strcpy would attempt to write past its
size, so this fixes this problem by switching to use strscpy.
Fixes: dcda165706b9 ("Bluetooth: hci_core: Fix build warnings")
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
The problem is detected by KASAN.
btrtl driver uses private hci data to store 'struct btrealtek_data'.
If btrtl driver is used with btusb, then memory for private hci data
is allocated in btusb. But no private data is allocated after hci_dev,
when btrtl is used with hci_h5.
This commit adds memory allocation for hci_h5 case.
==================================================================
BUG: KASAN: slab-out-of-bounds in btrtl_initialize+0x6cc/0x958 [btrtl]
Write of size 8 at addr ffff00000f5a5748 by task kworker/u9:0/76
Hardware name: Pine64 PinePhone (1.2) (DT)
Workqueue: hci0 hci_power_on [bluetooth]
Call trace:
dump_backtrace+0x9c/0x128
show_stack+0x20/0x38
dump_stack_lvl+0x48/0x60
print_report+0xf8/0x5d8
kasan_report+0x90/0xd0
__asan_store8+0x9c/0xc0
[btrtl]
h5_btrtl_setup+0xd0/0x2f8 [hci_uart]
h5_setup+0x50/0x80 [hci_uart]
hci_uart_setup+0xd4/0x260 [hci_uart]
hci_dev_open_sync+0x1cc/0xf68 [bluetooth]
hci_dev_do_open+0x34/0x90 [bluetooth]
hci_power_on+0xc4/0x3c8 [bluetooth]
process_one_work+0x328/0x6f0
worker_thread+0x410/0x778
kthread+0x168/0x178
ret_from_fork+0x10/0x20
Allocated by task 53:
kasan_save_stack+0x3c/0x68
kasan_save_track+0x20/0x40
kasan_save_alloc_info+0x68/0x78
__kasan_kmalloc+0xd4/0xd8
__kmalloc+0x1b4/0x3b0
hci_alloc_dev_priv+0x28/0xa58 [bluetooth]
hci_uart_register_device+0x118/0x4f8 [hci_uart]
h5_serdev_probe+0xf4/0x178 [hci_uart]
serdev_drv_probe+0x54/0xa0
really_probe+0x254/0x588
__driver_probe_device+0xc4/0x210
driver_probe_device+0x64/0x160
__driver_attach_async_helper+0x88/0x158
async_run_entry_fn+0xd0/0x388
process_one_work+0x328/0x6f0
worker_thread+0x410/0x778
kthread+0x168/0x178
ret_from_fork+0x10/0x20
Last potentially related work creation:
kasan_save_stack+0x3c/0x68
__kasan_record_aux_stack+0xb0/0x150
kasan_record_aux_stack_noalloc+0x14/0x20
__queue_work+0x33c/0x960
queue_work_on+0x98/0xc0
hci_recv_frame+0xc8/0x1e8 [bluetooth]
h5_complete_rx_pkt+0x2c8/0x800 [hci_uart]
h5_rx_payload+0x98/0xb8 [hci_uart]
h5_recv+0x158/0x3d8 [hci_uart]
hci_uart_receive_buf+0xa0/0xe8 [hci_uart]
ttyport_receive_buf+0xac/0x178
flush_to_ldisc+0x130/0x2c8
process_one_work+0x328/0x6f0
worker_thread+0x410/0x778
kthread+0x168/0x178
ret_from_fork+0x10/0x20
Second to last potentially related work creation:
kasan_save_stack+0x3c/0x68
__kasan_record_aux_stack+0xb0/0x150
kasan_record_aux_stack_noalloc+0x14/0x20
__queue_work+0x788/0x960
queue_work_on+0x98/0xc0
__hci_cmd_sync_sk+0x23c/0x7a0 [bluetooth]
__hci_cmd_sync+0x24/0x38 [bluetooth]
btrtl_initialize+0x760/0x958 [btrtl]
h5_btrtl_setup+0xd0/0x2f8 [hci_uart]
h5_setup+0x50/0x80 [hci_uart]
hci_uart_setup+0xd4/0x260 [hci_uart]
hci_dev_open_sync+0x1cc/0xf68 [bluetooth]
hci_dev_do_open+0x34/0x90 [bluetooth]
hci_power_on+0xc4/0x3c8 [bluetooth]
process_one_work+0x328/0x6f0
worker_thread+0x410/0x778
kthread+0x168/0x178
ret_from_fork+0x10/0x20
==================================================================
Fixes: 5b355944b190 ("Bluetooth: btrtl: Add btrealtek data struct")
Fixes: 044014ce85a1 ("Bluetooth: btrtl: Add Realtek devcoredump support")
Signed-off-by: Andrey Skvortsov <[email protected]>
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
In some cases uart-base drivers may need to use priv data. For
example, to store information needed for devcoredump.
Fixes: 044014ce85a1 ("Bluetooth: btrtl: Add Realtek devcoredump support")
Signed-off-by: Andrey Skvortsov <[email protected]>
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
In a few cases the stack may generate commands as responses to events
which would happen to overwrite the sent_cmd, so this attempts to store
the request in req_skb so even if sent_cmd is replaced with a new
command the pending request will remain in stored in req_skb.
Fixes: 6a98e3836fa2 ("Bluetooth: Add helper for serialized HCI command execution")
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
This used the hci_conn QoS to determine which PHY to scan when creating
a PA Sync.
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
If HCI_PA_SYNC flag is set it means there is a Periodic Advertising
Synchronization pending, so this attempts to locate the address passed
to HCI_OP_LE_PA_CREATE_SYNC and program it in the accept list so only
reports with that address are processed.
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
This adds support to reassemble PA data for a Broadcast Sink
listening socket. This is needed in case the BASE is received
fragmented in multiple PA reports.
PA data is first reassembled inside the hcon, before the BASE
is extracted and stored inside the socket. The length of the
le_per_adv_data hcon array has been raised to 1650, to accommodate
the maximum PA data length that can come fragmented, according to
spec.
Signed-off-by: Iulia Tanasescu <[email protected]>
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
This creates a hcon instance at bis listen, before the PA sync
procedure is started.
Signed-off-by: Iulia Tanasescu <[email protected]>
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
This fixes the following build regression:
drivers-bluetooth-btintel.c-btintel_read_version()-warn:
passing-zero-to-PTR_ERR
Fixes: b79e04091010 ("Bluetooth: btintel: Fix null ptr deref in btintel_read_version")
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
The optional variants for the gpiod_get() family of functions return NULL
if the GPIO in question is not associated with this device. They return
ERR_PTR() on any other error. NULL descriptors are graciously handled by
GPIOLIB and can be safely passed to any of the GPIO consumer interfaces
as they will return 0 and act as if the function succeeded. If one is
using the optional variant, then there's no point in checking for NULL.
Fixes: 6845667146a2 ("Bluetooth: hci_qca: Fix NULL vs IS_ERR_OR_NULL check in qca_serdev_probe")
Signed-off-by: Bartosz Golaszewski <[email protected]>
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
Firmware sequencer (FSEQ) is a common code shared across Bluetooth
and Wifi. Printing FSEQ will help to debug if there is any mismatch
between Bluetooth and Wifi FSEQ.
Signed-off-by: Kiran K <[email protected]>
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
While waiting for hci_dev_lock the hci_conn object may be cleanup
causing the following trace:
BUG: KASAN: slab-use-after-free in hci_connect_le_scan_cleanup+0x29/0x350
Read of size 8 at addr ffff888001a50a30 by task kworker/u3:1/111
CPU: 0 PID: 111 Comm: kworker/u3:1 Not tainted
6.8.0-rc2-00701-g8179b15ab3fd-dirty #6418
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.2-1.fc38
04/01/2014
Workqueue: hci0 hci_cmd_sync_work
Call Trace:
<TASK>
dump_stack_lvl+0x21/0x70
print_report+0xce/0x620
? preempt_count_sub+0x13/0xc0
? __virt_addr_valid+0x15f/0x310
? hci_connect_le_scan_cleanup+0x29/0x350
kasan_report+0xdf/0x110
? hci_connect_le_scan_cleanup+0x29/0x350
hci_connect_le_scan_cleanup+0x29/0x350
create_le_conn_complete+0x25c/0x2c0
Fixes: 881559af5f5c ("Bluetooth: hci_sync: Attempt to dequeue connection attempt")
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
Fixes the following trace where hci_acl_create_conn_sync attempts to
call hci_abort_conn_sync after timeout:
BUG: KASAN: slab-use-after-free in hci_abort_conn_sync
(net/bluetooth/hci_sync.c:5439)
Read of size 2 at addr ffff88800322c032 by task kworker/u3:2/36
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.2-1.fc38
04/01/2014
Workqueue: hci0 hci_cmd_sync_work
Call Trace:
<TASK>
dump_stack_lvl (./arch/x86/include/asm/irqflags.h:26
./arch/x86/include/asm/irqflags.h:67 ./arch/x86/include/asm/irqflags.h:127
lib/dump_stack.c:107)
print_report (mm/kasan/report.c:378 mm/kasan/report.c:488)
? preempt_count_sub (kernel/sched/core.c:5889)
? __virt_addr_valid (./arch/x86/include/asm/preempt.h:103 (discriminator 1)
./include/linux/rcupdate.h:865 (discriminator 1)
./include/linux/mmzone.h:2026 (discriminator 1)
arch/x86/mm/physaddr.c:65 (discriminator 1))
? hci_abort_conn_sync (net/bluetooth/hci_sync.c:5439)
kasan_report (mm/kasan/report.c:603)
? hci_abort_conn_sync (net/bluetooth/hci_sync.c:5439)
hci_abort_conn_sync (net/bluetooth/hci_sync.c:5439)
? __pfx_hci_abort_conn_sync (net/bluetooth/hci_sync.c:5433)
hci_acl_create_conn_sync (net/bluetooth/hci_sync.c:6681)
Fixes: 45340097ce6e ("Bluetooth: hci_conn: Only do ACL connections sequentially")
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
Since commit aed65af1cc2f ("drivers: make device_type const"), the driver
core can properly handle constant struct device_type. Move the bt_type and
bnep_type variables to be constant structures as well, placing it into
read-only memory which can not be modified at runtime.
Cc: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Ricardo B. Marliere <[email protected]>
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
Use devm_kstrdup() instead of hand-writing it.
It is less verbose.
Signed-off-by: Christophe JAILLET <[email protected]>
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
Use strreplace() instead of hand-writing it.
It is less verbose.
Signed-off-by: Christophe JAILLET <[email protected]>
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
If connection is still queued/pending in the cmd_sync queue it means no
command has been generated and it should be safe to just dequeue the
callback when it is being aborted.
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
This adds functions to queue, dequeue and lookup into the cmd_sync
list.
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
This fixes the UAF on __hci_acl_create_connection_sync caused by
connection abortion, it uses the same logic as to LE_LINK which uses
hci_cmd_sync_cancel to prevent the callback to run if the connection is
abort prematurely.
Reported-by: [email protected]
Fixes: 45340097ce6e ("Bluetooth: hci_conn: Only do ACL connections sequentially")
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
This aligns the use socket sk_timeo as conn_timeout when initiating a
connection and then use it when scheduling the resulting HCI command,
that way the command is actually aborted synchronously thus not
blocking commands generated by hci_abort_conn_sync to inform the
controller the connection is to be aborted.
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
Commit cec9f3c5561d ("Bluetooth: Remove BT_HS") removes config BT_HS, but
misses two "ifdef BT_HS" blocks in hci_event.c.
Remove this dead code from this removed config option.
Signed-off-by: Lukas Bulwahn <[email protected]>
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
With the last commit we moved to using the hci_sync queue for "Create
Connection" requests, removing the need for retrying the paging after
finished/failed "Create Connection" requests and after the end of
inquiries.
hci_conn_check_pending() was used to trigger this retry, we can remove it
now.
Note that we can also remove the special handling for COMMAND_DISALLOWED
errors in the completion handler of "Create Connection", because "Create
Connection" requests are now always serialized.
This is somewhat reverting commit 4c67bc74f016 ("[Bluetooth] Support
concurrent connect requests").
With this, the BT_CONNECT2 state of ACL hci_conn objects should now be
back to meaning only one thing: That we received a "Connection Request"
from another device (see hci_conn_request_evt), but the response to that
is going to be deferred.
Signed-off-by: Jonas Dreßler <[email protected]>
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
Pretty much all bluetooth chipsets only support paging a single device at
a time, and if they don't reject a secondary "Create Connection" request
while another is still ongoing, they'll most likely serialize those
requests in the firware.
With commit 4c67bc74f016 ("[Bluetooth] Support concurrent connect
requests") we started adding some serialization of our own in case the
adapter returns "Command Disallowed" HCI error.
This commit was using the BT_CONNECT2 state for the serialization, this
state is also used for a few more things (most notably to indicate we're
waiting for an inquiry to cancel) and therefore a bit unreliable. Also
not all BT firwares would respond with "Command Disallowed" on too many
connection requests, some will also respond with "Hardware Failure"
(BCM4378), and others will error out later and send a "Connect Complete"
event with error "Rejected Limited Resources" (Marvell 88W8897).
We can clean things up a bit and also make the serialization more reliable
by using our hci_sync machinery to always do "Create Connection" requests
in a sequential manner.
This is very similar to what we're already doing for establishing LE
connections, and it works well there.
Note that this causes a test failure in mgmt-tester (test "Pair Device
- Power off 1") because the hci_abort_conn_sync() changes the error we
return on timeout of the "Create Connection". We'll fix this on the
mgmt-tester side by adjusting the expected error for the test.
Signed-off-by: Jonas Dreßler <[email protected]>
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
BIG Sync (aka. Broadcast sink) requires to inform that the device is
connected when a data path is active otherwise userspace could attempt
to free resources allocated to the device object while scanning.
Fixes: 1d11d70d1f6b ("Bluetooth: ISO: Pass BIG encryption info through QoS")
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
High Speed, Alternate MAC and PHY (AMP) extension, has been removed from
Bluetooth Core specification on 5.3:
https://www.bluetooth.com/blog/new-core-specification-v5-3-feature-enhancements/
Fixes: 244bc377591c ("Bluetooth: Add BT_HS config option")
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
If hci_cmd_sync_complete() is triggered and skb is NULL, then
hdev->req_skb is NULL, which will cause this issue.
Reported-and-tested-by: [email protected]
Signed-off-by: Edward Adam Davis <[email protected]>
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
ida_alloc() and ida_free() should be preferred to the deprecated
ida_simple_get() and ida_simple_remove().
Note that the upper limit of ida_simple_get() is exclusive, but the one of
ida_alloc_max() is inclusive. So a -1 has been added when needed.
Signed-off-by: Christophe JAILLET <[email protected]>
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
Add VID 13d3 & PID 3602 for MediaTek MT7925 USB Bluetooth chip.
The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.
T: Bus=07 Lev=01 Prnt=01 Port=10 Cnt=02 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3602 Rev= 1.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us
I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
Signed-off-by: Ulrik Strid <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
If command has timed out call __hci_cmd_sync_cancel to notify the
hci_req since it will inevitably cause a timeout.
This also rework the code around __hci_cmd_sync_cancel since it was
wrongly assuming it needs to cancel timer as well, but sometimes the
timers have not been started or in fact they already had timed out in
which case they don't need to be cancel yet again.
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
We have error defines already, so let's use them.
Signed-off-by: Jonas Dreßler <[email protected]>
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
The "pending connections" feature was originally introduced with commit
4c67bc74f016 ("[Bluetooth] Support concurrent connect requests") and
6bd57416127e ("[Bluetooth] Handling pending connect attempts after
inquiry") to handle controllers supporting only a single connection request
at a time. Later things were extended to also cancel ongoing inquiries on
connect() with commit 89e65975fea5 ("Bluetooth: Cancel Inquiry before
Create Connection").
With commit a9de9248064b ("[Bluetooth] Switch from OGF+OCF to using only
opcodes"), hci_conn_check_pending() was introduced as a helper to
consolidate a few places where we check for pending connections (indicated
by the BT_CONNECT2 flag) and then try to connect.
This refactoring commit also snuck in two more calls to
hci_conn_check_pending():
- One is in the failure callback of hci_cs_inquiry(), this one probably
makes sense: If we send an "HCI Inquiry" command and then immediately
after a "Create Connection" command, the "Create Connection" command might
fail before the "HCI Inquiry" command, and then we want to retry the
"Create Connection" on failure of the "HCI Inquiry".
- The other added call to hci_conn_check_pending() is in the event handler
for the "Remote Name" event, this seems unrelated and is possibly a
copy-paste error, so remove that one.
Fixes: a9de9248064b ("[Bluetooth] Switch from OGF+OCF to using only opcodes")
Signed-off-by: Jonas Dreßler <[email protected]>
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
On a lot of platforms (at least the MS Surface devices, M1 macbooks, and
a few ThinkPads) firmware doesn't do its job when rfkilling a device
and the bluetooth adapter is not actually shut down properly on rfkill.
This leads to connected devices remaining in connected state and the
bluetooth connection eventually timing out after rfkilling an adapter.
Use the rfkill hook in the HCI driver to go through the full power-off
sequence (including stopping scans and disconnecting devices) before
rfkilling it, just like MGMT_OP_SET_POWERED would do.
In case anything during the larger power-off sequence fails, make sure
the device is still closed and the rfkill ends up being effective in
the end.
Signed-off-by: Jonas Dreßler <[email protected]>
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
Add a new state HCI_POWERING_DOWN that indicates that the device is
currently powering down, this will be useful for the next commit.
Signed-off-by: Jonas Dreßler <[email protected]>
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
Queuing of power_off work was introduced in these functions with commits
8b064a3ad377 ("Bluetooth: Clean up HCI state when doing power off") and
c9910d0fb4fc ("Bluetooth: Fix disconnecting connections in non-connected
states") in an effort to clean up state and do things like disconnecting
devices before actually powering off the device.
After that, commit a3172b7eb4a2 ("Bluetooth: Add timer to force power off")
introduced a timeout to ensure that the device actually got powered off,
even if some of the cleanup work would never complete.
This code later got refactored with commit cf75ad8b41d2 ("Bluetooth:
hci_sync: Convert MGMT_SET_POWERED"), which made powering off the device
synchronous and removed the need for initiating the power_off work from
other places. The timeout mentioned above got removed too, because we now
also made use of the command timeout during power on/off.
These days the power_off work still exists, but it only seems to only be
used for HCI_AUTO_OFF functionality, which is why we never noticed
those two leftover places where we queue power_off work. So let's remove
that code.
Fixes: cf75ad8b41d2 ("Bluetooth: hci_sync: Convert MGMT_SET_POWERED")
Signed-off-by: Jonas Dreßler <[email protected]>
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
With commit cf75ad8b41d2 ("Bluetooth: hci_sync: Convert MGMT_SET_POWERED"),
the power off sequence got refactored so that this timeout was no longer
necessary, let's remove the leftover define from the header too.
Fixes: cf75ad8b41d2 ("Bluetooth: hci_sync: Convert MGMT_SET_POWERED")
Signed-off-by: Jonas Dreßler <[email protected]>
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
This fixes the tx timeout issue seen while running a stress test on
btnxpuart for couple of hours, such that the interval between two HCI
commands coincide with the power save timeout value of 2 seconds.
Test procedure using bash script:
<load btnxpuart.ko>
hciconfig hci0 up
//Enable Power Save feature
hcitool -i hci0 cmd 3f 23 02 00 00
while (true)
do
hciconfig hci0 leadv
sleep 2
hciconfig hci0 noleadv
sleep 2
done
Error log, after adding few more debug prints:
Bluetooth: btnxpuart_queue_skb(): 01 0A 20 01 00
Bluetooth: hci0: Set UART break: on, status=0
Bluetooth: hci0: btnxpuart_tx_wakeup() tx_work scheduled
Bluetooth: hci0: btnxpuart_tx_work() dequeue: 01 0A 20 01 00
Can't set advertise mode on hci0: Connection timed out (110)
Bluetooth: hci0: command 0x200a tx timeout
When the power save mechanism turns on UART break, and btnxpuart_tx_work()
is scheduled simultaneously, psdata->ps_state is read as PS_STATE_AWAKE,
which prevents the psdata->work from being scheduled, which is responsible
to turn OFF UART break.
This issue is fixed by adding a ps_lock mutex around UART break on/off as
well as around ps_state read/write.
btnxpuart_tx_wakeup() will now read updated ps_state value. If ps_state is
PS_STATE_SLEEP, it will first schedule psdata->work, and then it will
reschedule itself once UART break has been turned off and ps_state is
PS_STATE_AWAKE.
Tested above script for 50,000 iterations and TX timeout error was not
observed anymore.
Signed-off-by: Neeraj Sanjay Kale <[email protected]>
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
Add the support for RTL8852BT/RTL8852BE-VT BT controller on USB interface.
The necessary firmware will be submitted to linux-firmware project.
The device info from /sys/kernel/debug/usb/devices as below.
T: Bus=02 Lev=02 Prnt=02 Port=05 Cnt=01 Dev#= 8 Spd=12 MxCh= 0
D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0bda ProdID=8520 Rev= 0.00
S: Manufacturer=Realtek
S: Product=Bluetooth Radio
S: SerialNumber=00e04c000001
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Max Chou <[email protected]>
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
Since commit 43a7206b0963 ("driver core: class: make class_register() take
a const *"), the driver core allows for struct class to be in read-only
memory, so move the wpan_phy_class structure to be declared at build time
placing it into read-only memory, instead of having to be dynamically
allocated at boot time.
Cc: Greg Kroah-Hartman <[email protected]>
Suggested-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Ricardo B. Marliere <[email protected]>
Acked-by: Miquel Raynal <[email protected]>
Message-ID: <[email protected]>
[changed prefix from wifi to ieee802154 by [email protected]]
Signed-off-by: Stefan Schmidt <[email protected]>
|
|
of_gpio.h is deprecated and subject to remove.
The driver doesn't use it, simply remove the unused header.
Signed-off-by: Andy Shevchenko <[email protected]>
Acked-by: Miquel Raynal <[email protected]>
Message-ID: <[email protected]>
Signed-off-by: Stefan Schmidt <[email protected]>
|
|
of_gpio.h is deprecated and subject to remove.
The driver doesn't use it directly, replace it
with what is really being used.
Signed-off-by: Andy Shevchenko <[email protected]>
Acked-by: Miquel Raynal <[email protected]>
Message-ID: <[email protected]>
Signed-off-by: Stefan Schmidt <[email protected]>
|
|
mac802154_llsec_key_del() can free resources of a key directly without
following the RCU rules for waiting before the end of a grace period. This
may lead to use-after-free in case llsec_lookup_key() is traversing the
list of keys in parallel with a key deletion:
refcount_t: addition on 0; use-after-free.
WARNING: CPU: 4 PID: 16000 at lib/refcount.c:25 refcount_warn_saturate+0x162/0x2a0
Modules linked in:
CPU: 4 PID: 16000 Comm: wpan-ping Not tainted 6.7.0 #19
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.2-debian-1.16.2-1 04/01/2014
RIP: 0010:refcount_warn_saturate+0x162/0x2a0
Call Trace:
<TASK>
llsec_lookup_key.isra.0+0x890/0x9e0
mac802154_llsec_encrypt+0x30c/0x9c0
ieee802154_subif_start_xmit+0x24/0x1e0
dev_hard_start_xmit+0x13e/0x690
sch_direct_xmit+0x2ae/0xbc0
__dev_queue_xmit+0x11dd/0x3c20
dgram_sendmsg+0x90b/0xd60
__sys_sendto+0x466/0x4c0
__x64_sys_sendto+0xe0/0x1c0
do_syscall_64+0x45/0xf0
entry_SYSCALL_64_after_hwframe+0x6e/0x76
Also, ieee802154_llsec_key_entry structures are not freed by
mac802154_llsec_key_del():
unreferenced object 0xffff8880613b6980 (size 64):
comm "iwpan", pid 2176, jiffies 4294761134 (age 60.475s)
hex dump (first 32 bytes):
78 0d 8f 18 80 88 ff ff 22 01 00 00 00 00 ad de x.......".......
00 00 00 00 00 00 00 00 03 00 cd ab 00 00 00 00 ................
backtrace:
[<ffffffff81dcfa62>] __kmem_cache_alloc_node+0x1e2/0x2d0
[<ffffffff81c43865>] kmalloc_trace+0x25/0xc0
[<ffffffff88968b09>] mac802154_llsec_key_add+0xac9/0xcf0
[<ffffffff8896e41a>] ieee802154_add_llsec_key+0x5a/0x80
[<ffffffff8892adc6>] nl802154_add_llsec_key+0x426/0x5b0
[<ffffffff86ff293e>] genl_family_rcv_msg_doit+0x1fe/0x2f0
[<ffffffff86ff46d1>] genl_rcv_msg+0x531/0x7d0
[<ffffffff86fee7a9>] netlink_rcv_skb+0x169/0x440
[<ffffffff86ff1d88>] genl_rcv+0x28/0x40
[<ffffffff86fec15c>] netlink_unicast+0x53c/0x820
[<ffffffff86fecd8b>] netlink_sendmsg+0x93b/0xe60
[<ffffffff86b91b35>] ____sys_sendmsg+0xac5/0xca0
[<ffffffff86b9c3dd>] ___sys_sendmsg+0x11d/0x1c0
[<ffffffff86b9c65a>] __sys_sendmsg+0xfa/0x1d0
[<ffffffff88eadbf5>] do_syscall_64+0x45/0xf0
[<ffffffff890000ea>] entry_SYSCALL_64_after_hwframe+0x6e/0x76
Handle the proper resource release in the RCU callback function
mac802154_llsec_key_del_rcu().
Note that if llsec_lookup_key() finds a key, it gets a refcount via
llsec_key_get() and locally copies key id from key_entry (which is a
list element). So it's safe to call llsec_key_put() and free the list
entry after the RCU grace period elapses.
Found by Linux Verification Center (linuxtesting.org).
Fixes: 5d637d5aabd8 ("mac802154: add llsec structures and mutators")
Cc: [email protected]
Signed-off-by: Fedor Pchelkin <[email protected]>
Acked-by: Alexander Aring <[email protected]>
Message-ID: <[email protected]>
Signed-off-by: Stefan Schmidt <[email protected]>
|
|
Introduce ixgbe_update_{r,t}x_ring_stats() that will be used by both
standard and ZC datapath.
Signed-off-by: Maciej Fijalkowski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The "qv_info" ptr cannot be NULL when it gets the address of
an element of the flexible array "qvlist_info->qv_info".
Detected using the static analysis tool - Svace.
Signed-off-by: Alexey Kodanev <[email protected]>
Tested-by: Pucha Himasekhar Reddy <[email protected]> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <[email protected]>
|
|
There are currently two pairs of identical checks and calls
to iavf_{add|del}_cloud_filter().
Detected using the static analysis tool - Svace.
Signed-off-by: Alexey Kodanev <[email protected]>
Reviewed-by: Ahmed Zaki <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Following the addition of new GTP RSS hash options to ethtool.h, this patch
implements the corresponding RSS settings for GTP packets in the Intel ice
driver. It enables users to configure RSS for GTP-U and GTP-C traffic over IPv4
and IPv6, utilizing the newly defined hash options.
The implementation covers the handling of gtpu(4|6), gtpc(4|6), gtpc(4|6)t,
gtpu(4|6)e, gtpu(4|6)u, and gtpu(4|6)d traffic, providing enhanced load
distribution for GTP traffic across multiple processing units.
Signed-off-by: Takeru Hayasaka <[email protected]>
Reviewed-by: Marcin Szycik <[email protected]>
Tested-by: Pucha Himasekhar Reddy <[email protected]> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <[email protected]>
|