| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The ifindex doesn't have to be unique for multiple network namespaces on
the same machine.
$ ip netns add test1
$ ip -net test1 link add dummy1 type dummy
$ ip netns add test2
$ ip -net test2 link add dummy2 type dummy
$ ip -net test1 link show dev dummy1
6: dummy1: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 96:81:55:1e:dd:85 brd ff:ff:ff:ff:ff:ff
$ ip -net test2 link show dev dummy2
6: dummy2: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 5a:3c:af:35:07:c3 brd ff:ff:ff:ff:ff:ff
But the batman-adv code to walk through the various layers of virtual
interfaces uses this assumption because dev_get_iflink handles it
internally and doesn't return the actual netns of the iflink. And
dev_get_iflink only documents the situation where ifindex == iflink for
physical devices.
But only checking for dev->netdev_ops->ndo_get_iflink is also not an option
because ipoib_get_iflink implements it even when it sometimes returns an
iflink != ifindex and sometimes iflink == ifindex. The caller must
therefore make sure itself to check both netns and iflink + ifindex for
equality. Only when they are equal, a "physical" interface was detected
which should stop the traversal. On the other hand, vxcan_get_iflink can
also return 0 in case there was currently no valid peer. In this case, it
is still necessary to stop.
Fixes: b7eddd0b3950 ("batman-adv: prevent using any virtual device created on batman-adv as hard-interface")
Fixes: 5ed4a460a1d3 ("batman-adv: additional checks for virtual interfaces on top of WiFi")
Reported-by: Sabrina Dubroca <[email protected]>
Signed-off-by: Sven Eckelmann <[email protected]>
Signed-off-by: Simon Wunderlich <[email protected]>
|
|
There is no need to call dev_get_iflink multiple times for the same
net_device in batadv_get_real_netdevice. And since some of the
ndo_get_iflink callbacks are dynamic (for example via RCUs like in
vxcan_get_iflink), it could easily happen that the returned values are not
stable. The pre-checks before __dev_get_by_index are then of course bogus.
Fixes: 5ed4a460a1d3 ("batman-adv: additional checks for virtual interfaces on top of WiFi")
Signed-off-by: Sven Eckelmann <[email protected]>
Signed-off-by: Simon Wunderlich <[email protected]>
|
|
There is no need to call dev_get_iflink multiple times for the same
net_device in batadv_is_on_batman_iface. And since some of the
.ndo_get_iflink callbacks are dynamic (for example via RCUs like in
vxcan_get_iflink), it could easily happen that the returned values are not
stable. The pre-checks before __dev_get_by_index are then of course bogus.
Fixes: b7eddd0b3950 ("batman-adv: prevent using any virtual device created on batman-adv as hard-interface")
Signed-off-by: Sven Eckelmann <[email protected]>
Signed-off-by: Simon Wunderlich <[email protected]>
|
|
Before these changes elan_suspend() would only disable the regulator
when device_may_wakeup() returns false; whereas elan_resume() would
unconditionally enable it, leading to an enable count imbalance when
device_may_wakeup() returns true.
This triggers the "WARN_ON(regulator->enable_count)" in regulator_put()
when the elan_i2c driver gets unbound, this happens e.g. with the
hot-plugable dock with Elan I2C touchpad for the Asus TF103C 2-in-1.
Fix this by making the regulator_enable() call also be conditional
on device_may_wakeup() returning false.
Signed-off-by: Hans de Goede <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
elan_disable_power() is called conditionally on suspend, where as
elan_enable_power() is always called on resume. This leads to
an imbalance in the regulator's enable count.
Move the regulator_[en|dis]able() calls out of elan_[en|dis]able_power()
in preparation of fixing this.
No functional changes intended.
Signed-off-by: Hans de Goede <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
[dtor: consolidate elan_[en|dis]able() into elan_set_power()]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
When trying to add a histogram against an event with the "cpu" field, it
was impossible due to "cpu" being a keyword to key off of the running CPU.
So to fix this, it was changed to "common_cpu" to match the other generic
fields (like "common_pid"). But since some scripts used "cpu" for keying
off of the CPU (for events that did not have "cpu" as a field, which is
most of them), a backward compatibility trick was added such that if "cpu"
was used as a key, and the event did not have "cpu" as a field name, then
it would fallback and switch over to "common_cpu".
This fix has a couple of subtle bugs. One was that when switching over to
"common_cpu", it did not change the field name, it just set a flag. But
the code still found a "cpu" field. The "cpu" field is used for filtering
and is returned when the event does not have a "cpu" field.
This was found by:
# cd /sys/kernel/tracing
# echo hist:key=cpu,pid:sort=cpu > events/sched/sched_wakeup/trigger
# cat events/sched/sched_wakeup/hist
Which showed the histogram unsorted:
{ cpu: 19, pid: 1175 } hitcount: 1
{ cpu: 6, pid: 239 } hitcount: 2
{ cpu: 23, pid: 1186 } hitcount: 14
{ cpu: 12, pid: 249 } hitcount: 2
{ cpu: 3, pid: 994 } hitcount: 5
Instead of hard coding the "cpu" checks, take advantage of the fact that
trace_event_field_field() returns a special field for "cpu" and "CPU" if
the event does not have "cpu" as a field. This special field has the
"filter_type" of "FILTER_CPU". Check that to test if the returned field is
of the CPU type instead of doing the string compare.
Also, fix the sorting bug by testing for the hist_field flag of
HIST_FIELD_FL_CPU when setting up the sort routine. Otherwise it will use
the special CPU field to know what compare routine to use, and since that
special field does not have a size, it returns tracing_map_cmp_none.
Cc: [email protected]
Fixes: 1e3bac71c505 ("tracing/histogram: Rename "cpu" to "common_cpu"")
Reported-by: Daniel Bristot de Oliveira <[email protected]>
Signed-off-by: Steven Rostedt (Google) <[email protected]>
|
|
When the DSA_NOTIFIER_TAG_PROTO returns an error, the user space process
which initiated the protocol change exits the kernel processing while
still holding the rtnl_mutex. So any other process attempting to lock
the rtnl_mutex would deadlock after such event.
The error handling of DSA_NOTIFIER_TAG_PROTO was inadvertently changed
by the blamed commit, introducing this regression. We must still call
rtnl_unlock(), and we must still call DSA_NOTIFIER_TAG_PROTO for the old
protocol. The latter is due to the limiting design of notifier chains
for cross-chip operations, which don't have a built-in error recovery
mechanism - we should look into using notifier_call_chain_robust for that.
Fixes: dc452a471dba ("net: dsa: introduce tagger-owned storage for private and shared data")
Signed-off-by: Vladimir Oltean <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Luiz Augusto von Dentz says:
====================
bluetooth pull request for net:
- Fix regression with scanning not working in some systems.
* tag 'for-net-2022-03-01' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: Fix not checking MGMT cmd pending queue
====================
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
A number of places in the MGMT handlers we examine the command queue for
other commands (in progress but not yet complete) that will interact
with the process being performed. However, not all commands go into the
queue if one of:
1. There is no negative side effect of consecutive or redundent commands
2. The command is entirely perform "inline".
This change examines each "pending command" check, and if it is not
needed, deletes the check. Of the remaining pending command checks, we
make sure that the command is in the pending queue by using the
mgmt_pending_add/mgmt_pending_remove pair rather than the
mgmt_pending_new/mgmt_pending_free pair.
Link: https://lore.kernel.org/linux-bluetooth/[email protected]/T/
Tested-by: Maxim Levitsky <[email protected]>
Signed-off-by: Brian Gix <[email protected]>
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
1) Use kfree_rcu(ptr, rcu) variant, using kfree_rcu(ptr) was not
intentional. From Eric Dumazet.
2) Use-after-free in netfilter hook core, from Eric Dumazet.
3) Missing rcu read lock side for netfilter egress hook,
from Florian Westphal.
4) nf_queue assume state->sk is full socket while it might not be.
Invoke sock_gen_put(), from Florian Westphal.
5) Add selftest to exercise the reported KASAN splat in 4)
6) Fix possible use-after-free in nf_queue in case sk_refcnt is 0.
Also from Florian.
7) Use input interface index only for hardware offload, not for
the software plane. This breaks tc ct action. Patch from Paul Blakey.
* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
net/sched: act_ct: Fix flow table lookup failure with no originating ifindex
netfilter: nf_queue: handle socket prefetch
netfilter: nf_queue: fix possible use-after-free
selftests: netfilter: add nfqueue TCP_NEW_SYN_RECV socket race test
netfilter: nf_queue: don't assume sk is full socket
netfilter: egress: silence egress hook lockdep splats
netfilter: fix use-after-free in __nf_register_net_hook()
netfilter: nf_tables: prefer kfree_rcu(ptr, rcu) variant
====================
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
After cited commit optimizted hw insertion, flow table entries are
populated with ifindex information which was intended to only be used
for HW offload. This tuple ifindex is hashed in the flow table key, so
it must be filled for lookup to be successful. But tuple ifindex is only
relevant for the netfilter flowtables (nft), so it's not filled in
act_ct flow table lookup, resulting in lookup failure, and no SW
offload and no offload teardown for TCP connection FIN/RST packets.
To fix this, add new tc ifindex field to tuple, which will
only be used for offloading, not for lookup, as it will not be
part of the tuple hash.
Fixes: 9795ded7f924 ("net/sched: act_ct: Fill offloading tuple iifidx")
Signed-off-by: Paul Blakey <[email protected]>
Signed-off-by: Pablo Neira Ayuso <[email protected]>
|
|
Pull kvm fixes from Paolo Bonzini:
"The bigger part of the change is a revert for x86 hosts. Here the
second patch was supposed to fix the first, but in reality it was just
as broken, so both have to go.
x86 host:
- Revert incorrect assumption that cr3 changes come with preempt
notifier callbacks (they don't when static branches are changed,
for example)
ARM host:
- Correctly synchronise PMR and co on PSCI CPU_SUSPEND
- Skip tests that depend on GICv3 when the HW isn't available"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: selftests: aarch64: Skip tests if we can't create a vgic-v3
Revert "KVM: VMX: Save HOST_CR3 in vmx_prepare_switch_to_guest()"
Revert "KVM: VMX: Save HOST_CR3 in vmx_set_host_fs_gs()"
KVM: arm64: Don't miss pending interrupts for suspended vCPU
|
|
s390 has a swap_ex_entry_fixup function, however it is not being used
since common code expects a swap_ex_entry_fixup define. If it is not
defined the default implementation will be used. So fix this by adding
a proper define.
However also the implementation of the function must be fixed, since a
NULL value for handler has a special meaning and must not be adjusted.
Luckily all of this doesn't fix a real bug currently: the main extable
is correctly sorted during build time, and for runtime sorting there
is currently no case where the handler field is not NULL.
Fixes: 05a68e892e89 ("s390/kernel: expand exception table logic to allow new handling options")
Acked-by: Ilya Leoshkevich <[email protected]>
Reviewed-by: Alexander Gordeev <[email protected]>
Signed-off-by: Heiko Carstens <[email protected]>
Signed-off-by: Vasily Gorbik <[email protected]>
|
|
arch_ftrace_get_regs is supposed to return a struct pt_regs pointer
only if the pt_regs structure contains all register contents, which
means it must have been populated when created via ftrace_regs_caller.
If it was populated via ftrace_caller the contents are not complete
(the psw mask part is missing), and therefore a NULL pointer needs be
returned.
The current code incorrectly always returns a struct pt_regs pointer.
Fix this by adding another pt_regs flag which indicates if the
contents are complete, and fix arch_ftrace_get_regs accordingly.
Fixes: 894979689d3a ("s390/ftrace: provide separate ftrace_caller/ftrace_regs_caller implementations")
Reported-by: Christophe Leroy <[email protected]>
Reported-by: Naveen N. Rao <[email protected]>
Reviewed-by: Sven Schnelle <[email protected]>
Acked-by: Ilya Leoshkevich <[email protected]>
Signed-off-by: Heiko Carstens <[email protected]>
Signed-off-by: Vasily Gorbik <[email protected]>
|
|
ftrace_caller was used for both ftrace_caller and ftrace_regs_caller,
which means that the target address of the hotpatch trampoline was
never updated.
With commit 894979689d3a ("s390/ftrace: provide separate
ftrace_caller/ftrace_regs_caller implementations") a separate
ftrace_regs_caller entry point was implemeted, however it was
forgotten to implement the necessary changes for ftrace_modify_call
and ftrace_make_call, where the branch target has to be modified
accordingly.
Therefore add the missing code now.
Fixes: 894979689d3a ("s390/ftrace: provide separate ftrace_caller/ftrace_regs_caller implementations")
Reviewed-by: Sven Schnelle <[email protected]>
Acked-by: Ilya Leoshkevich <[email protected]>
Signed-off-by: Heiko Carstens <[email protected]>
Signed-off-by: Vasily Gorbik <[email protected]>
|
|
We need to preserve the values at OLDMEM_BASE and OLDMEM_SIZE which are
used by zgetdump in case when kdump crashes. In that case zgetdump will
attempt to read OLDMEM_BASE and OLDMEM_SIZE in order to find out where
the memory range [0 - OLDMEM_SIZE] belonging to the production kernel is.
Fixes: f1a546947431 ("s390/setup: don't reserve memory that occupied decompressor's head")
Cc: [email protected] # 5.15+
Signed-off-by: Alexander Egorenkov <[email protected]>
Acked-by: Vasily Gorbik <[email protected]>
Signed-off-by: Vasily Gorbik <[email protected]>
|
|
VRR capable property is not attached by default to the connector
It is attached only if VRR is supported.
So if the driver tries to call drm core set prop function without
it being attached that causes NULL dereference.
Cc: Jani Nikula <[email protected]>
Cc: Ville Syrjälä <[email protected]>
Cc: [email protected]
Signed-off-by: Manasi Navare <[email protected]>
Reviewed-by: Ville Syrjälä <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull binfmt_elf fix from Kees Cook:
"This addresses a regression[1] under ia64 where some ET_EXEC binaries
were not loading"
Link: https://linux-regtracking.leemhuis.info/regzbot/regression/[email protected]/ [1]
- Fix ia64 ET_EXEC loading
* tag 'binfmt_elf-v5.17-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
binfmt_elf: Avoid total_mapping_size for ET_EXEC
|
|
Partially revert commit 5f501d555653 ("binfmt_elf: reintroduce using
MAP_FIXED_NOREPLACE"), which applied the ET_DYN "total_mapping_size"
logic also to ET_EXEC.
At least ia64 has ET_EXEC PT_LOAD segments that are not virtual-address
contiguous (but _are_ file-offset contiguous). This would result in a
giant mapping attempting to cover the entire span, including the virtual
address range hole, and well beyond the size of the ELF file itself,
causing the kernel to refuse to load it. For example:
$ readelf -lW /usr/bin/gcc
...
Program Headers:
Type Offset VirtAddr PhysAddr FileSiz MemSiz ...
...
LOAD 0x000000 0x4000000000000000 0x4000000000000000 0x00b5a0 0x00b5a0 ...
LOAD 0x00b5a0 0x600000000000b5a0 0x600000000000b5a0 0x0005ac 0x000710 ...
...
^^^^^^^^ ^^^^^^^^^^^^^^^^^^ ^^^^^^^^ ^^^^^^^^
File offset range : 0x000000-0x00bb4c
0x00bb4c bytes
Virtual address range : 0x4000000000000000-0x600000000000bcb0
0x200000000000bcb0 bytes
Remove the total_mapping_size logic for ET_EXEC, which reduces the
ET_EXEC MAP_FIXED_NOREPLACE coverage to only the first PT_LOAD (better
than nothing), and retains it for ET_DYN.
Ironically, this is the reverse of the problem that originally caused
problems with MAP_FIXED_NOREPLACE: overlapping PT_LOAD segments. Future
work could restore full coverage if load_elf_binary() were to perform
mappings in a separate phase from the loading (where it could resolve
both overlaps and holes).
Cc: Eric Biederman <[email protected]>
Cc: Alexander Viro <[email protected]>
Cc: [email protected]
Cc: [email protected]
Reported-by: matoro <[email protected]>
Fixes: 5f501d555653 ("binfmt_elf: reintroduce using MAP_FIXED_NOREPLACE")
Link: https://lore.kernel.org/r/[email protected]
Tested-by: matoro <[email protected]>
Link: https://lore.kernel.org/lkml/[email protected]
Tested-By: John Paul Adrian Glaubitz <[email protected]>
Link: https://lore.kernel.org/lkml/[email protected]
Cc: [email protected]
Signed-off-by: Kees Cook <[email protected]>
|
|
Do not call get_trip_hyst() from thermal_genl_cmd_tz_get_trip() if
the thermal zone does not define one.
Fixes: 1ce50e7d408e ("thermal: core: genetlink support for events/cmd/sampling")
Signed-off-by: Nicolas Cavallari <[email protected]>
Cc: 5.10+ <[email protected]> # 5.10+
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
johannes Berg says:
====================
Some last-minute fixes:
* rfkill
- add missing rfill_soft_blocked() when disabled
* cfg80211
- handle a nla_memdup() failure correctly
- fix CONFIG_CFG80211_EXTRA_REGDB_KEYDIR typo in
Makefile
* mac80211
- fix EAPOL handling in 802.3 RX path
- reject setting up aggregation sessions before
connection is authorized to avoid timeouts or
similar
- handle some SAE authentication steps correctly
- fix AC selection in mesh forwarding
* iwlwifi
- remove TWT support as it causes firmware crashes
when the AP isn't behaving correctly
- check debugfs pointer before dereferncing it
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
The kbuild change here accidentally removed not only the
unquoting, but also the last character of the variable
name. Fix that.
Fixes: 129ab0d2d9f3 ("kbuild: do not quote string values in include/config/auto.conf")
Reviewed-by: Masahiro Yamada <[email protected]>
Link: https://lore.kernel.org/r/20220221155512.1d25895f7c5f.I50fa3d4189fcab90a2896fe8cae215035dae9508@changeid
Signed-off-by: Johannes Berg <[email protected]>
|
|
In case someone combines bpf socket assign and nf_queue, then we will
queue an skb who references a struct sock that did not have its
reference count incremented.
As we leave rcu protection, there is no guarantee that skb->sk is still
valid.
For refcount-less skb->sk case, try to increment the reference count
and then override the destructor.
In case of failure we have two choices: orphan the skb and 'delete'
preselect or let nf_queue() drop the packet.
Do the latter, it should not happen during normal operation.
Fixes: cf7fbe660f2d ("bpf: Add socket assign support")
Acked-by: Joe Stringer <[email protected]>
Signed-off-by: Florian Westphal <[email protected]>
|
|
Eric Dumazet says:
The sock_hold() side seems suspect, because there is no guarantee
that sk_refcnt is not already 0.
On failure, we cannot queue the packet and need to indicate an
error. The packet will be dropped by the caller.
v2: split skb prefetch hunk into separate change
Fixes: 271b72c7fa82c ("udp: RCU handling for Unicast packets.")
Reported-by: Eric Dumazet <[email protected]>
Reviewed-by: Eric Dumazet <[email protected]>
Signed-off-by: Florian Westphal <[email protected]>
|
|
causes:
BUG: KASAN: slab-out-of-bounds in sk_free+0x25/0x80
Write of size 4 at addr ffff888106df0284 by task nf-queue/1459
sk_free+0x25/0x80
nf_queue_entry_release_refs+0x143/0x1a0
nf_reinject+0x233/0x770
... without 'netfilter: nf_queue: don't assume sk is full socket'.
Signed-off-by: Florian Westphal <[email protected]>
|
|
There is no guarantee that state->sk refers to a full socket.
If refcount transitions to 0, sock_put calls sk_free which then ends up
with garbage fields.
I'd like to thank Oleksandr Natalenko and Jiri Benc for considerable
debug work and pointing out state->sk oddities.
Fixes: ca6fb0651883 ("tcp: attach SYNACK messages to request sockets instead of listener")
Tested-by: Oleksandr Natalenko <[email protected]>
Signed-off-by: Florian Westphal <[email protected]>
|
|
When we get anti-clogging token required (added by the commit
mentioned below), or the other status codes added by the later
commit 4e56cde15f7d ("mac80211: Handle special status codes in
SAE commit") we currently just pretend (towards the internal
state machine of authentication) that we didn't receive anything.
This has the undesirable consequence of retransmitting the prior
frame, which is not expected, because the timer is still armed.
If we just disarm the timer at that point, it would result in
the undesirable side effect of being in this state indefinitely
if userspace crashes, or so.
So to fix this, reset the timer and set a new auth_data->waiting
in order to have no more retransmissions, but to have the data
destroyed when the timer actually fires, which will only happen
if userspace didn't continue (i.e. crashed or abandoned it.)
Fixes: a4055e74a2ff ("mac80211: Don't destroy auth data in case of anti-clogging")
Reported-by: Jouni Malinen <[email protected]>
Link: https://lore.kernel.org/r/20220224103932.75964e1d7932.Ia487f91556f29daae734bf61f8181404642e1eec@changeid
Signed-off-by: Johannes Berg <[email protected]>
|
|
As there's potential for failure of the nla_memdup(),
check the return value.
Fixes: a442b761b24b ("cfg80211: add add_nan_func / del_nan_func")
Signed-off-by: Jiasheng Jiang <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Johannes Berg <[email protected]>
|
|
When "debugfs=off" is used on the kernel command line, iwiwifi's
mvm module uses an invalid/unchecked debugfs_dir pointer and causes
a BUG:
BUG: kernel NULL pointer dereference, address: 000000000000004f
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: 0000 [#1] PREEMPT SMP
CPU: 1 PID: 503 Comm: modprobe Tainted: G W 5.17.0-rc5 #7
Hardware name: Dell Inc. Inspiron 15 5510/076F7Y, BIOS 2.4.1 11/05/2021
RIP: 0010:iwl_mvm_dbgfs_register+0x692/0x700 [iwlmvm]
Code: 69 a0 be 80 01 00 00 48 c7 c7 50 73 6a a0 e8 95 cf ee e0 48 8b 83 b0 1e 00 00 48 c7 c2 54 73 6a a0 be 64 00 00 00 48 8d 7d 8c <48> 8b 48 50 e8 15 22 07 e1 48 8b 43 28 48 8d 55 8c 48 c7 c7 5f 73
RSP: 0018:ffffc90000a0ba68 EFLAGS: 00010246
RAX: ffffffffffffffff RBX: ffff88817d6e3328 RCX: ffff88817d6e3328
RDX: ffffffffa06a7354 RSI: 0000000000000064 RDI: ffffc90000a0ba6c
RBP: ffffc90000a0bae0 R08: ffffffff824e4880 R09: ffffffffa069d620
R10: ffffc90000a0ba00 R11: ffffffffffffffff R12: 0000000000000000
R13: ffffc90000a0bb28 R14: ffff88817d6e3328 R15: ffff88817d6e3320
FS: 00007f64dd92d740(0000) GS:ffff88847f640000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000000000000004f CR3: 000000016fc79001 CR4: 0000000000770ee0
PKRU: 55555554
Call Trace:
<TASK>
? iwl_mvm_mac_setup_register+0xbdc/0xda0 [iwlmvm]
iwl_mvm_start_post_nvm+0x71/0x100 [iwlmvm]
iwl_op_mode_mvm_start+0xab8/0xb30 [iwlmvm]
_iwl_op_mode_start+0x6f/0xd0 [iwlwifi]
iwl_opmode_register+0x6a/0xe0 [iwlwifi]
? 0xffffffffa0231000
iwl_mvm_init+0x35/0x1000 [iwlmvm]
? 0xffffffffa0231000
do_one_initcall+0x5a/0x1b0
? kmem_cache_alloc+0x1e5/0x2f0
? do_init_module+0x1e/0x220
do_init_module+0x48/0x220
load_module+0x2602/0x2bc0
? __kernel_read+0x145/0x2e0
? kernel_read_file+0x229/0x290
__do_sys_finit_module+0xc5/0x130
? __do_sys_finit_module+0xc5/0x130
__x64_sys_finit_module+0x13/0x20
do_syscall_64+0x38/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f64dda564dd
Code: 5b 41 5c c3 66 0f 1f 84 00 00 00 00 00 f3 0f 1e fa 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 1b 29 0f 00 f7 d8 64 89 01 48
RSP: 002b:00007ffdba393f88 EFLAGS: 00000246 ORIG_RAX: 0000000000000139
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f64dda564dd
RDX: 0000000000000000 RSI: 00005575399e2ab2 RDI: 0000000000000001
RBP: 000055753a91c5e0 R08: 0000000000000000 R09: 0000000000000002
R10: 0000000000000001 R11: 0000000000000246 R12: 00005575399e2ab2
R13: 000055753a91ceb0 R14: 0000000000000000 R15: 000055753a923018
</TASK>
Modules linked in: btintel(+) btmtk bluetooth vfat snd_hda_codec_hdmi fat snd_hda_codec_realtek snd_hda_codec_generic iwlmvm(+) snd_sof_pci_intel_tgl mac80211 snd_sof_intel_hda_common soundwire_intel soundwire_generic_allocation soundwire_cadence soundwire_bus snd_sof_intel_hda snd_sof_pci snd_sof snd_sof_xtensa_dsp snd_soc_hdac_hda snd_hda_ext_core snd_soc_acpi_intel_match snd_soc_acpi snd_soc_core btrfs snd_compress snd_hda_intel snd_intel_dspcfg snd_intel_sdw_acpi snd_hda_codec raid6_pq iwlwifi snd_hda_core snd_pcm snd_timer snd soundcore cfg80211 intel_ish_ipc(+) thunderbolt rfkill intel_ishtp ucsi_acpi wmi i2c_hid_acpi i2c_hid evdev
CR2: 000000000000004f
---[ end trace 0000000000000000 ]---
Check the debugfs_dir pointer for an error before using it.
Fixes: 8c082a99edb9 ("iwlwifi: mvm: simplify iwl_mvm_dbgfs_register")
Signed-off-by: Randy Dunlap <[email protected]>
Cc: Luca Coelho <[email protected]>
Cc: [email protected]
Cc: Kalle Valo <[email protected]>
Cc: Greg Kroah-Hartman <[email protected]>
Cc: Emmanuel Grumbach <[email protected]>
Cc: stable <[email protected]>
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
[change to make both conditional]
Signed-off-by: Johannes Berg <[email protected]>
|
|
Some APs misbehave when TWT is used and cause our firmware to crash.
We don't know a reasonable way to detect and work around this problem
in the FW yet. To prevent these crashes, disable TWT in the driver by
stopping to advertise TWT support.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215523
Signed-off-by: Golan Ben Ami <[email protected]>
[reworded the commit message]
Signed-off-by: Luca Coelho <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Johannes Berg <[email protected]>
|
|
If CONFIG_RFKILL is not set, the Intel WiFi driver will not build
the iw_mvm driver part due to the missing rfill_soft_blocked()
call. Adding a inline declaration of rfill_soft_blocked() if
CONFIG_RFKILL=n fixes the following error:
drivers/net/wireless/intel/iwlwifi/mvm/mvm.h: In function 'iwl_mvm_mei_set_sw_rfkill_state':
drivers/net/wireless/intel/iwlwifi/mvm/mvm.h:2215:38: error: implicit declaration of function 'rfkill_soft_blocked'; did you mean 'rfkill_blocked'? [-Werror=implicit-function-declaration]
2215 | mvm->hw_registered ? rfkill_soft_blocked(mvm->hw->wiphy->rfkill) : false;
| ^~~~~~~~~~~~~~~~~~~
| rfkill_blocked
Signed-off-by: Ben Dooks <[email protected]>
Reported-by: Neill Whillans <[email protected]>
Fixes: 5bc9a9dd7535 ("rfkill: allow to get the software rfkill state")
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Johannes Berg <[email protected]>
|
|
It was the intention to reverse the bits, not make them all zero by
using logical NOT operator.
Fixes: cc19db8b312a ("MIPS: ralink: mt7621: do memory detection on KSEG1")
Suggested-by: Chuanhong Guo <[email protected]>
Signed-off-by: Ilya Lipnitskiy <[email protected]>
Reviewed-by: Sergio Paracuellos <[email protected]>
Signed-off-by: Thomas Bogendoerfer <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-02-28
This series contains updates to igc and e1000e drivers.
Corinna Vinschen ensures release of hardware sempahore on failed
register read in igc_read_phy_reg_gpy().
Sasha does the same for the write variant, igc_write_phy_reg_gpy(). On
e1000e, he resolves an issue with hardware unit hang on s0ix exit
by disabling some bits and LAN connected device reset during power
management flows. Lastly, he allows for TGP platforms to correct its
NVM checksum.
v2: Fix Fixes tag on patch 3
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
Interrupt() resource
ACPI/x86 devices with a Cherry Trail SoC should have a GpioInt + a regular
GPIO ACPI resource in their ACPI tables.
Some CHT devices have a bug, where the also is bogus interrupt resource
(likely copied from a previous Bay Trail based generation of the device).
The i2c-core-acpi code will assign the bogus, non-working, interrupt
resource to client->irq. Add a workaround to fix this up.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=2043960
Signed-off-by: Hans de Goede <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
Use the new soc_intel_is_byt() helper from linux/platform_data/x86/soc.h.
Signed-off-by: Hans de Goede <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
Merge with mainline to get the Intel ASoC generic helpers header and
other changes.
|
|
This driver, like several others, uses a chained IRQ for each GPIO bank,
and forwards .irq_set_wake to the GPIO bank's upstream IRQ. As a result,
a call to irq_set_irq_wake() needs to lock both the upstream and
downstream irq_desc's. Lockdep considers this to be a possible deadlock
when the irq_desc's share lockdep classes, which they do by default:
============================================
WARNING: possible recursive locking detected
5.17.0-rc3-00394-gc849047c2473 #1 Not tainted
--------------------------------------------
init/307 is trying to acquire lock:
c2dfe27c (&irq_desc_lock_class){-.-.}-{2:2}, at: __irq_get_desc_lock+0x58/0xa0
but task is already holding lock:
c3c0ac7c (&irq_desc_lock_class){-.-.}-{2:2}, at: __irq_get_desc_lock+0x58/0xa0
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&irq_desc_lock_class);
lock(&irq_desc_lock_class);
*** DEADLOCK ***
May be due to missing lock nesting notation
4 locks held by init/307:
#0: c1f29f18 (system_transition_mutex){+.+.}-{3:3}, at: __do_sys_reboot+0x90/0x23c
#1: c20f7760 (&dev->mutex){....}-{3:3}, at: device_shutdown+0xf4/0x224
#2: c2e804d8 (&dev->mutex){....}-{3:3}, at: device_shutdown+0x104/0x224
#3: c3c0ac7c (&irq_desc_lock_class){-.-.}-{2:2}, at: __irq_get_desc_lock+0x58/0xa0
stack backtrace:
CPU: 0 PID: 307 Comm: init Not tainted 5.17.0-rc3-00394-gc849047c2473 #1
Hardware name: Allwinner sun8i Family
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x68/0x90
dump_stack_lvl from __lock_acquire+0x1680/0x31a0
__lock_acquire from lock_acquire+0x148/0x3dc
lock_acquire from _raw_spin_lock_irqsave+0x50/0x6c
_raw_spin_lock_irqsave from __irq_get_desc_lock+0x58/0xa0
__irq_get_desc_lock from irq_set_irq_wake+0x2c/0x19c
irq_set_irq_wake from irq_set_irq_wake+0x13c/0x19c
[tail call from sunxi_pinctrl_irq_set_wake]
irq_set_irq_wake from gpio_keys_suspend+0x80/0x1a4
gpio_keys_suspend from gpio_keys_shutdown+0x10/0x2c
gpio_keys_shutdown from device_shutdown+0x180/0x224
device_shutdown from __do_sys_reboot+0x134/0x23c
__do_sys_reboot from ret_fast_syscall+0x0/0x1c
However, this can never deadlock because the upstream and downstream
IRQs are never the same (nor do they even involve the same irqchip).
Silence this erroneous lockdep splat by applying what appears to be the
usual fix of moving the GPIO IRQs to separate lockdep classes.
Fixes: a59c99d9eaf9 ("pinctrl: sunxi: Forward calls to irq_set_irq_wake")
Reported-by: Guenter Roeck <[email protected]>
Signed-off-by: Samuel Holland <[email protected]>
Reviewed-by: Jernej Skrabec <[email protected]>
Tested-by: Guenter Roeck <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Linus Walleij <[email protected]>
|
|
The commit that sets the direction directly without calling
pinctrl_gpio_direction(), forgot to add chip->base to the offset when
calling sunxi_pmx_gpio_set_direction().
This caused failures for various Allwinner boards which have two
GPIO blocks.
Signed-off-by: Hans Verkuil <[email protected]>
Reported-by: 5kft <[email protected]>
Suggested-by: 5kft <[email protected]>
Reported-by: Corentin Labbe <[email protected]>
Fixes: 8df89a7cbc63 (pinctrl-sunxi: don't call pinctrl_gpio_direction())
Tested-by: Corentin Labbe <[email protected]>
Tested-by: Jernej Skrabec <[email protected]>
Acked-by: Jernej Skrabec <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Guenter Roeck <[email protected]>
[Picked from linux-next to pinctrl fixes]
Signed-off-by: Linus Walleij <[email protected]>
|
|
Update MAC type check e1000_pch_tgp because for e1000_pch_cnp,
NVM checksum update is still possible.
Emit a more detailed warning message.
Bugzilla: https://bugzilla.opensuse.org/show_bug.cgi?id=1191663
Fixes: 4051f68318ca ("e1000e: Do not take care about recovery NVM checksum")
Reported-by: Thomas Bogendoerfer <[email protected]>
Signed-off-by: Sasha Neftin <[email protected]>
Tested-by: Naama Meir <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Disable the OEM bit/Gig Disable/restart AN impact and disable the PHY
LAN connected device (LCD) reset during power management flows. This
fixes possible HW unit hangs on the s0ix exit on some corporate ADL
platforms.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=214821
Fixes: 3e55d231716e ("e1000e: Add handshake with the CSME to support S0ix")
Suggested-by: Dima Ruinskiy <[email protected]>
Suggested-by: Nir Efrati <[email protected]>
Signed-off-by: Sasha Neftin <[email protected]>
Tested-by: Kai-Heng Feng <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Netfilter assumes its called with rcu_read_lock held, but in egress
hook case it may be called with BH readlock.
This triggers lockdep splat.
In order to avoid to change all rcu_dereference() to
rcu_dereference_check(..., rcu_read_lock_bh_held()), wrap nf_hook_slow
with read lock/unlock pair.
Reported-by: Eric Dumazet <[email protected]>
Signed-off-by: Florian Westphal <[email protected]>
Signed-off-by: Pablo Neira Ayuso <[email protected]>
|
|
We must not dereference @new_hooks after nf_hook_mutex has been released,
because other threads might have freed our allocated hooks already.
BUG: KASAN: use-after-free in nf_hook_entries_get_hook_ops include/linux/netfilter.h:130 [inline]
BUG: KASAN: use-after-free in hooks_validate net/netfilter/core.c:171 [inline]
BUG: KASAN: use-after-free in __nf_register_net_hook+0x77a/0x820 net/netfilter/core.c:438
Read of size 2 at addr ffff88801c1a8000 by task syz-executor237/4430
CPU: 1 PID: 4430 Comm: syz-executor237 Not tainted 5.17.0-rc5-syzkaller-00306-g2293be58d6a1 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
print_address_description.constprop.0.cold+0x8d/0x336 mm/kasan/report.c:255
__kasan_report mm/kasan/report.c:442 [inline]
kasan_report.cold+0x83/0xdf mm/kasan/report.c:459
nf_hook_entries_get_hook_ops include/linux/netfilter.h:130 [inline]
hooks_validate net/netfilter/core.c:171 [inline]
__nf_register_net_hook+0x77a/0x820 net/netfilter/core.c:438
nf_register_net_hook+0x114/0x170 net/netfilter/core.c:571
nf_register_net_hooks+0x59/0xc0 net/netfilter/core.c:587
nf_synproxy_ipv6_init+0x85/0xe0 net/netfilter/nf_synproxy_core.c:1218
synproxy_tg6_check+0x30d/0x560 net/ipv6/netfilter/ip6t_SYNPROXY.c:81
xt_check_target+0x26c/0x9e0 net/netfilter/x_tables.c:1038
check_target net/ipv6/netfilter/ip6_tables.c:530 [inline]
find_check_entry.constprop.0+0x7f1/0x9e0 net/ipv6/netfilter/ip6_tables.c:573
translate_table+0xc8b/0x1750 net/ipv6/netfilter/ip6_tables.c:735
do_replace net/ipv6/netfilter/ip6_tables.c:1153 [inline]
do_ip6t_set_ctl+0x56e/0xb90 net/ipv6/netfilter/ip6_tables.c:1639
nf_setsockopt+0x83/0xe0 net/netfilter/nf_sockopt.c:101
ipv6_setsockopt+0x122/0x180 net/ipv6/ipv6_sockglue.c:1024
rawv6_setsockopt+0xd3/0x6a0 net/ipv6/raw.c:1084
__sys_setsockopt+0x2db/0x610 net/socket.c:2180
__do_sys_setsockopt net/socket.c:2191 [inline]
__se_sys_setsockopt net/socket.c:2188 [inline]
__x64_sys_setsockopt+0xba/0x150 net/socket.c:2188
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f65a1ace7d9
Code: 28 00 00 00 75 05 48 83 c4 28 c3 e8 71 15 00 00 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b8 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007f65a1a7f308 EFLAGS: 00000246 ORIG_RAX: 0000000000000036
RAX: ffffffffffffffda RBX: 0000000000000006 RCX: 00007f65a1ace7d9
RDX: 0000000000000040 RSI: 0000000000000029 RDI: 0000000000000003
RBP: 00007f65a1b574c8 R08: 0000000000000001 R09: 0000000000000000
R10: 0000000020000000 R11: 0000000000000246 R12: 00007f65a1b55130
R13: 00007f65a1b574c0 R14: 00007f65a1b24090 R15: 0000000000022000
</TASK>
The buggy address belongs to the page:
page:ffffea0000706a00 refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x1c1a8
flags: 0xfff00000000000(node=0|zone=1|lastcpupid=0x7ff)
raw: 00fff00000000000 ffffea0001c1b108 ffffea000046dd08 0000000000000000
raw: 0000000000000000 0000000000000000 00000000ffffffff 0000000000000000
page dumped because: kasan: bad access detected
page_owner tracks the page as freed
page last allocated via order 2, migratetype Unmovable, gfp_mask 0x52dc0(GFP_KERNEL|__GFP_NOWARN|__GFP_NORETRY|__GFP_COMP|__GFP_ZERO), pid 4430, ts 1061781545818, free_ts 1061791488993
prep_new_page mm/page_alloc.c:2434 [inline]
get_page_from_freelist+0xa72/0x2f50 mm/page_alloc.c:4165
__alloc_pages+0x1b2/0x500 mm/page_alloc.c:5389
__alloc_pages_node include/linux/gfp.h:572 [inline]
alloc_pages_node include/linux/gfp.h:595 [inline]
kmalloc_large_node+0x62/0x130 mm/slub.c:4438
__kmalloc_node+0x35a/0x4a0 mm/slub.c:4454
kmalloc_node include/linux/slab.h:604 [inline]
kvmalloc_node+0x97/0x100 mm/util.c:580
kvmalloc include/linux/slab.h:731 [inline]
kvzalloc include/linux/slab.h:739 [inline]
allocate_hook_entries_size net/netfilter/core.c:61 [inline]
nf_hook_entries_grow+0x140/0x780 net/netfilter/core.c:128
__nf_register_net_hook+0x144/0x820 net/netfilter/core.c:429
nf_register_net_hook+0x114/0x170 net/netfilter/core.c:571
nf_register_net_hooks+0x59/0xc0 net/netfilter/core.c:587
nf_synproxy_ipv6_init+0x85/0xe0 net/netfilter/nf_synproxy_core.c:1218
synproxy_tg6_check+0x30d/0x560 net/ipv6/netfilter/ip6t_SYNPROXY.c:81
xt_check_target+0x26c/0x9e0 net/netfilter/x_tables.c:1038
check_target net/ipv6/netfilter/ip6_tables.c:530 [inline]
find_check_entry.constprop.0+0x7f1/0x9e0 net/ipv6/netfilter/ip6_tables.c:573
translate_table+0xc8b/0x1750 net/ipv6/netfilter/ip6_tables.c:735
do_replace net/ipv6/netfilter/ip6_tables.c:1153 [inline]
do_ip6t_set_ctl+0x56e/0xb90 net/ipv6/netfilter/ip6_tables.c:1639
nf_setsockopt+0x83/0xe0 net/netfilter/nf_sockopt.c:101
page last free stack trace:
reset_page_owner include/linux/page_owner.h:24 [inline]
free_pages_prepare mm/page_alloc.c:1352 [inline]
free_pcp_prepare+0x374/0x870 mm/page_alloc.c:1404
free_unref_page_prepare mm/page_alloc.c:3325 [inline]
free_unref_page+0x19/0x690 mm/page_alloc.c:3404
kvfree+0x42/0x50 mm/util.c:613
rcu_do_batch kernel/rcu/tree.c:2527 [inline]
rcu_core+0x7b1/0x1820 kernel/rcu/tree.c:2778
__do_softirq+0x29b/0x9c2 kernel/softirq.c:558
Memory state around the buggy address:
ffff88801c1a7f00: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ffff88801c1a7f80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
>ffff88801c1a8000: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
^
ffff88801c1a8080: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ffff88801c1a8100: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
Fixes: 2420b79f8c18 ("netfilter: debug: check for sorted array")
Signed-off-by: Eric Dumazet <[email protected]>
Reported-by: syzbot <[email protected]>
Acked-by: Florian Westphal <[email protected]>
Signed-off-by: Pablo Neira Ayuso <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"The code changes address mostly minor problems:
- Several NXP/FSL SoC driver fixes, addressing issues with error
handling and compilation
- Fix a clock disabling imbalance in gpcv2 driver.
- Arm Juno DMA coherency issue
- Trivial firmware driver fixes for op-tee and scmi firmware
The remaining changes address issues in the devicetree files:
- A timer regression for the OMAP devkit8000, which has to use the
alternative timer.
- A hang in the i.MX8MM power domain configuration
- Multiple fixes for the Rockchip RK3399 addressing issues with sound
and eMMC
- Cosmetic fixes for i.MX8ULP, RK3xxx, and Tegra124"
* tag 'soc-fixes-5.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (32 commits)
ARM: tegra: Move panels to AUX bus
soc: imx: gpcv2: Fix clock disabling imbalance in error path
soc: fsl: qe: Check of ioremap return value
soc: fsl: qe: fix typo in a comment
soc: fsl: guts: Add a missing memory allocation failure check
soc: fsl: guts: Revert commit 3c0d64e867ed
soc: fsl: Correct MAINTAINERS database (SOC)
soc: fsl: Correct MAINTAINERS database (QUICC ENGINE LIBRARY)
soc: fsl: Replace kernel.h with the necessary inclusions
dt-bindings: fsl,layerscape-dcfg: add missing compatible for lx2160a
dt-bindings: qoriq-clock: add missing compatible for lx2160a
ARM: dts: Use 32KiHz oscillator on devkit8000
ARM: dts: switch timer config to common devkit8000 devicetree
tee: optee: fix error return code in probe function
arm64: dts: imx8ulp: Set #thermal-sensor-cells to 1 as required
arm64: dts: imx8mm: Fix VPU Hanging
ARM: dts: rockchip: fix a typo on rk3288 crypto-controller
ARM: dts: rockchip: reorder rk322x hmdi clocks
firmware: arm_scmi: Remove space in MODULE_ALIAS name
arm64: dts: agilex: use the compatible "intel,socfpga-agilex-hsotg"
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi
Pull EFI fixes from Ard Biesheuvel:
- don't treat valid hartid U32_MAX as a failure return code (RISC-V)
- avoid blocking query_variable_info() call when blocking is not
allowed
* tag 'efi-urgent-for-v5.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi:
efivars: Respect "block" flag in efivar_entry_set_safe()
riscv/efi_stub: Fix get_boot_hartid_from_fdt() return value
|
|
Without DRM_GEM_CMA_HELPER HDLCD won't build. This needs to be there too.
Fixes: 09717af7d13d ("drm: Remove CONFIG_DRM_KMS_CMA_HELPER option")
Reviewed-by: Steven Price <[email protected]>
Signed-off-by: Carsten Haitzler <[email protected]>
Acked-by: Liviu Dudau <[email protected]>
Signed-off-by: Rob Herring <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
The PM Runtime docs say:
Drivers in ->remove() callback should undo the runtime PM changes done
in ->probe(). Usually this means calling pm_runtime_disable(),
pm_runtime_dont_use_autosuspend() etc.
We weren't doing that for autosuspend. Let's do it.
Fixes: 9bede63127c6 ("drm/bridge: ti-sn65dsi86: Use pm_runtime autosuspend")
Signed-off-by: Douglas Anderson <[email protected]>
Reviewed-by: Linus Walleij <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/20220222141838.1.If784ba19e875e8ded4ec4931601ce6d255845245@changeid
|
|
Similar to "igc_read_phy_reg_gpy: drop premature return" patch.
igc_write_phy_reg_gpy checks the return value from igc_write_phy_reg_mdic
and if it's not 0, returns immediately. By doing this, it leaves the HW
semaphore in the acquired state.
Drop this premature return statement, the function returns after
releasing the semaphore immediately anyway.
Fixes: 5586838fe9ce ("igc: Add code for PHY support")
Suggested-by: Dima Ruinskiy <[email protected]>
Reported-by: Corinna Vinschen <[email protected]>
Signed-off-by: Sasha Neftin <[email protected]>
Tested-by: Naama Meir <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
igc_read_phy_reg_gpy checks the return value from igc_read_phy_reg_mdic
and if it's not 0, returns immediately. By doing this, it leaves the HW
semaphore in the acquired state.
Drop this premature return statement, the function returns after
releasing the semaphore immediately anyway.
Fixes: 5586838fe9ce ("igc: Add code for PHY support")
Signed-off-by: Corinna Vinschen <[email protected]>
Acked-by: Sasha Neftin <[email protected]>
Tested-by: Naama Meir <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
early_param() handlers should return 0 on success.
__setup() handlers should return 1 on success, i.e., the parameter
has been handled. A return of 0 would cause the "option=value" string
to be added to init's environment strings, polluting it.
../arch/arm/mm/mmu.c: In function 'test_early_cachepolicy':
../arch/arm/mm/mmu.c:215:1: error: no return statement in function returning non-void [-Werror=return-type]
../arch/arm/mm/mmu.c: In function 'test_noalign_setup':
../arch/arm/mm/mmu.c:221:1: error: no return statement in function returning non-void [-Werror=return-type]
Fixes: b849a60e0903 ("ARM: make cr_alignment read-only #ifndef CONFIG_CPU_CP15")
Signed-off-by: Randy Dunlap <[email protected]>
Reported-by: Igor Zhbanov <[email protected]>
Cc: Uwe Kleine-König <[email protected]>
Cc: [email protected]
Cc: [email protected]
Signed-off-by: Russell King (Oracle) <[email protected]>
|
|
When tracing the whole disk, 'dropped' and 'msg' will be created
under 'q->debugfs_dir' and 'bt->dir' is NULL, thus blk_trace_free()
won't remove those files. What's worse, the following UAF can be
triggered because of accessing stale 'dropped' and 'msg':
==================================================================
BUG: KASAN: use-after-free in blk_dropped_read+0x89/0x100
Read of size 4 at addr ffff88816912f3d8 by task blktrace/1188
CPU: 27 PID: 1188 Comm: blktrace Not tainted 5.17.0-rc4-next-20220217+ #469
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS ?-20190727_073836-4
Call Trace:
<TASK>
dump_stack_lvl+0x34/0x44
print_address_description.constprop.0.cold+0xab/0x381
? blk_dropped_read+0x89/0x100
? blk_dropped_read+0x89/0x100
kasan_report.cold+0x83/0xdf
? blk_dropped_read+0x89/0x100
kasan_check_range+0x140/0x1b0
blk_dropped_read+0x89/0x100
? blk_create_buf_file_callback+0x20/0x20
? kmem_cache_free+0xa1/0x500
? do_sys_openat2+0x258/0x460
full_proxy_read+0x8f/0xc0
vfs_read+0xc6/0x260
ksys_read+0xb9/0x150
? vfs_write+0x3d0/0x3d0
? fpregs_assert_state_consistent+0x55/0x60
? exit_to_user_mode_prepare+0x39/0x1e0
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7fbc080d92fd
Code: ce 20 00 00 75 10 b8 00 00 00 00 0f 05 48 3d 01 f0 ff ff 73 31 c3 48 83 1
RSP: 002b:00007fbb95ff9cb0 EFLAGS: 00000293 ORIG_RAX: 0000000000000000
RAX: ffffffffffffffda RBX: 00007fbb95ff9dc0 RCX: 00007fbc080d92fd
RDX: 0000000000000100 RSI: 00007fbb95ff9cc0 RDI: 0000000000000045
RBP: 0000000000000045 R08: 0000000000406299 R09: 00000000fffffffd
R10: 000000000153afa0 R11: 0000000000000293 R12: 00007fbb780008c0
R13: 00007fbb78000938 R14: 0000000000608b30 R15: 00007fbb780029c8
</TASK>
Allocated by task 1050:
kasan_save_stack+0x1e/0x40
__kasan_kmalloc+0x81/0xa0
do_blk_trace_setup+0xcb/0x410
__blk_trace_setup+0xac/0x130
blk_trace_ioctl+0xe9/0x1c0
blkdev_ioctl+0xf1/0x390
__x64_sys_ioctl+0xa5/0xe0
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
Freed by task 1050:
kasan_save_stack+0x1e/0x40
kasan_set_track+0x21/0x30
kasan_set_free_info+0x20/0x30
__kasan_slab_free+0x103/0x180
kfree+0x9a/0x4c0
__blk_trace_remove+0x53/0x70
blk_trace_ioctl+0x199/0x1c0
blkdev_common_ioctl+0x5e9/0xb30
blkdev_ioctl+0x1a5/0x390
__x64_sys_ioctl+0xa5/0xe0
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
The buggy address belongs to the object at ffff88816912f380
which belongs to the cache kmalloc-96 of size 96
The buggy address is located 88 bytes inside of
96-byte region [ffff88816912f380, ffff88816912f3e0)
The buggy address belongs to the page:
page:000000009a1b4e7c refcount:1 mapcount:0 mapping:0000000000000000 index:0x0f
flags: 0x17ffffc0000200(slab|node=0|zone=2|lastcpupid=0x1fffff)
raw: 0017ffffc0000200 ffffea00044f1100 dead000000000002 ffff88810004c780
raw: 0000000000000000 0000000000200020 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff88816912f280: fa fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc
ffff88816912f300: fa fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc
>ffff88816912f380: fa fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc
^
ffff88816912f400: fa fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc
ffff88816912f480: fa fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc
==================================================================
Fixes: c0ea57608b69 ("blktrace: remove debugfs file dentries from struct blk_trace")
Signed-off-by: Yu Kuai <[email protected]>
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jens Axboe <[email protected]>
|