| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
SB Temperature Sensor Interface (SB-TSI) is an SMBus compatible
interface that reports AMD SoC's Ttcl (normalized temperature),
and resembles a typical 8-pin remote temperature sensor's I2C interface
to BMC.
This commit adds basic support using this interface to read CPU
temperature, and read/write high/low CPU temp thresholds.
To instantiate this driver on an AMD CPU with SB-TSI
support, the i2c bus number would be the bus connected from the board
management controller (BMC) to the CPU. The i2c address is specified in
Section 6.3.1 of the spec [1]: The SB-TSI address is normally 98h for
socket 0 and 90h for socket 1, but it could vary based on hardware address
select pins.
[1]: https://www.amd.com/system/files/TechDocs/56255_OSRR.pdf
Test status: tested reading temp1_input, and reading/writing
temp1_max/min.
Signed-off-by: Kun Yi <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Guenter Roeck <[email protected]>
|
|
As the IIO hardware monitoring driver does not have any code or data
located in initmem, there is no need to annotate the iio_hwmon_driver
structure with __refdata. Drop the annotation, to avoid suppressing
future section warnings.
Signed-off-by: Geert Uytterhoeven <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Guenter Roeck <[email protected]>
|
|
As the X-Gene hardware monitoring driver does not have any code or data
located in initmem, there is no need to annotate the xgene_hwmon_driver
structure with __refdata. Drop the annotation, to avoid suppressing
future section warnings.
Signed-off-by: Geert Uytterhoeven <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Guenter Roeck <[email protected]>
|
|
Convert the Analog Devices ADM1275 bindings to dt-schema.
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Reviewed-by: Rob Herring <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
[groeck: Removed unnecessary type ($ref) declaration]
Signed-off-by: Guenter Roeck <[email protected]>
|
|
The latest version of the On-Chip Controller (OCC) has a different
format for the temperature sensor data. Add a new temperature sensor
version to handle this data.
Signed-off-by: Eddie James <[email protected]>
Reviewed-by: Joel Stanley <[email protected]>
Signed-off-by: Joel Stanley <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Guenter Roeck <[email protected]>
|
|
The P10 OCC has a different SRAM address for the command and response
buffers. In addition, the SBE commands to access the SRAM have changed
format. Add versioning to the driver to handle these differences.
Signed-off-by: Eddie James <[email protected]>
Reviewed-by: Joel Stanley <[email protected]>
Signed-off-by: Joel Stanley <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Guenter Roeck <[email protected]>
|
|
Add the P10 compatible string.
Signed-off-by: Eddie James <[email protected]>
Reviewed-by: Joel Stanley <[email protected]>
Signed-off-by: Joel Stanley <[email protected]>
Acked-by: Rob Herring <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Guenter Roeck <[email protected]>
|
|
Convert the TI ADS7828 bindings to dt-schema.
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Reviewed-by: Rob Herring <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Guenter Roeck <[email protected]>
|
|
Convert the Analog Devices AD741x bindings to dt-schema.
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Reviewed-by: Rob Herring <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Guenter Roeck <[email protected]>
|
|
Convert the TI INA2xx bindings to dt-schema.
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Reviewed-by: Rob Herring <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Guenter Roeck <[email protected]>
|
|
There are several occurrances of a less than zero error check on
a u32 unsigned integer. These will never be true. Fix this by making
reg_value a plain int.
Addresses-Coverity: ("Unsigned comparison against zero")
Fixes: e126370240e0 ("hwmon: (ltc2992) Add support")
Signed-off-by: Colin Ian King <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Guenter Roeck <[email protected]>
|
|
Commit b722d7b9e4da ("hwmon: (pmbus) Driver for Delta power supplies
Q54SJ108A2") provides new documentation for DELTA Q54SJ108A2NC* drivers,
but the title underline was too short.
make htmldocs warns:
Documentation/hwmon/q54sj108a2.rst:4: WARNING: Title underline too short.
Adjust the title underline to the correct length.
Signed-off-by: Lukas Bulwahn <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
[groeck: Adjust subject]
Signed-off-by: Guenter Roeck <[email protected]>
|
|
Add documentation for ltc2992.
Signed-off-by: Alexandru Tachici <[email protected]>
Reviewed-by: Rob Herring <[email protected]>
Signed-off-by: Guenter Roeck <[email protected]>
|
|
LTC2992 has 4 open-drain GPIOS. This patch exports to user
space the 4 GPIOs using the GPIO driver Linux API.
Signed-off-by: Alexandru Tachici <[email protected]>
Signed-off-by: Guenter Roeck <[email protected]>
|
|
LTC2992 is a rail-to-rail system monitor that
measures current, voltage, and power of two supplies.
Two ADCs simultaneously measure each supply’s current.
A third ADC monitors the input voltages and four
auxiliary external voltages.
Signed-off-by: Alexandru Tachici <[email protected]>
Signed-off-by: Guenter Roeck <[email protected]>
|
|
The driver supports Q54SJ108A2 series modules of Delta.
Standard attributes are in sysfs, and other attributes are in debugfs.
Signed-off-by: xiao.ma <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
[groeck: Replaced spaces with tabs, dropped excessive spaces,
fixed module prefix in documentation]
Signed-off-by: Guenter Roeck <[email protected]>
|
|
Add the pmbus driver for the STMicroelectronics pm6764 voltage regulator.
the output voltage use the MFR_READ_VOUT 0xD4
vout value returned is linear11
Signed-off-by: Charles Hsu <[email protected]>
[groeck: Fixed various compile errors; marked pm6764tr_of_match __maybe_unused]
Signed-off-by: Guenter Roeck <[email protected]>
|
|
This is found on many MSI motherboards.
Signed-off-by: David Bartley <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Guenter Roeck <[email protected]>
|
|
This patch adds the DMI Product ID for Intel-based Xserve machines.
They use the same SMC accessible from the same data ports.
The 'Xserve' product ID only resolves to SMC-containing
Intel-based Xserves, as the PowerPC machines are identified
by the 'RackMac' identifier.
Tested on: Xserve3,1
Tested-by: Joe Jamison <[email protected]> # Xserve3,1
Signed-off-by: Joe Jamison <[email protected]>
Signed-off-by: Guenter Roeck <[email protected]>
|
|
The pwm-fan driver is updated to use the recommended API.
Signed-off-by: Paul Barker <[email protected]>
[groeck: Dropped unused variable]
Signed-off-by: Guenter Roeck <[email protected]>
|
|
Use platform_irq_count to determine the number of fan tachometer inputs
configured in the device tree. At this stage we support either 0 or 1
inputs.
Once we have this information we only need to read the
pulses-per-revolution value if a fan tachometer is actually configured
via an IRQ value.
Also add a debug print of the IRQ number and the pulses-per-revolution
value to aid in investigating issues.
Signed-off-by: Paul Barker <[email protected]>
Reviewed-by: Guenter Roeck <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Guenter Roeck <[email protected]>
|
|
fixed the following coccicheck:
drivers/hwmon/abx500.c:266:60-61: WARNING opportunity for kobj_to_dev().
Signed-off-by: Tian Tao <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Guenter Roeck <[email protected]>
|
|
Add documentation for the max127 hardware monitoring driver.
Signed-off-by: Tao Ren <[email protected]>
Reviewed-by: Guenter Roeck <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Guenter Roeck <[email protected]>
|
|
Add hardware monitoring driver for the Maxim MAX127 chip.
MAX127 min/max range handling code is inspired by the max197 driver.
Signed-off-by: Tao Ren <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Guenter Roeck <[email protected]>
|
|
Document and give an example of how to define multiple fan tachometer
inputs for the pwm-fan driver.
Signed-off-by: Paul Barker <[email protected]>
Reviewed-by: Rob Herring <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Guenter Roeck <[email protected]>
|
|
This patch fix a trivial typo temperatire => temperature.
Signed-off-by: Corentin Labbe <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Guenter Roeck <[email protected]>
|
|
Update the supported processors and mention vulnerability fix.
Signed-off-by: Naveen Krishna Chatradhi <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Guenter Roeck <[email protected]>
|
|
Add X86 CPU match for AMD family 19h model 01h. This is necessary to
enable support for energy reporting via the amd_energy module.
Signed-off-by: Naveen Krishna Chatradhi <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Guenter Roeck <[email protected]>
|
|
The correct fan rpm value is also a LINEAR11 value but without a factor.
Verified by using the fan test button on the psu to let the fan spin up
to maximum for some seconds.
Fixes: 933222c98445 ("hwmon: (corsair-psu) fix unintentional sign extension issue")
Signed-off-by: Wilken Gottwalt <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Guenter Roeck <[email protected]>
|
|
Fixes the following W=1 kernel build warning(s):
from drivers/hwmon/ibmpowernv.c:11:
In function ‘strncpy’,
inlined from ‘get_sensor_index_attr’ at drivers/hwmon/ibmpowernv.c:243:2,
inlined from ‘create_device_attrs’ at drivers/hwmon/ibmpowernv.c:280:8:
include/linux/string.h:297:30: warning: ‘__builtin_strncpy’ specified bound 32 equals destination size [-Wstringop-truncation]
297 | #define __underlying_strncpy __builtin_strncpy
| ^
include/linux/string.h:307:9: note: in expansion of macro ‘__underlying_strncpy’
307 | return __underlying_strncpy(p, q, size);
| ^~~~~~~~~~~~~~~~~~~~
Cc: Jean Delvare <[email protected]>
Cc: Guenter Roeck <[email protected]>
Cc: Michael Ellerman <[email protected]>
Cc: Benjamin Herrenschmidt <[email protected]>
Cc: Paul Mackerras <[email protected]>
Cc: Neelesh Gupta <[email protected]>
Cc: [email protected]
Cc: [email protected]
Signed-off-by: Lee Jones <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Guenter Roeck <[email protected]>
|
|
This is the only use of kerneldoc in the sourcefile and no
descriptions are provided.
Fixes the following W=1 kernel build warning(s):
drivers/hwmon/ina3221.c:152: warning: Function parameter or member 'ina' not described in 'ina3221_summation_shunt_resistor'
Cc: "Andrew F. Davis" <[email protected]>
Signed-off-by: Lee Jones <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Guenter Roeck <[email protected]>
|
|
Kerneldoc expects attributes/parameters to be in '@*.: ' format.
Also fix repeated word "the the".
Fixes the following W=1 kernel build warning(s):
drivers/hwmon/adm1177.c:40: warning: Function parameter or member 'client' not described in 'adm1177_state'
drivers/hwmon/adm1177.c:40: warning: Function parameter or member 'reg' not described in 'adm1177_state'
drivers/hwmon/adm1177.c:40: warning: Function parameter or member 'r_sense_uohm' not described in 'adm1177_state'
drivers/hwmon/adm1177.c:40: warning: Function parameter or member 'alert_threshold_ua' not described in 'adm1177_state'
drivers/hwmon/adm1177.c:40: warning: Function parameter or member 'vrange_high' not described in 'adm1177_state'
Cc: Beniamin Bia <[email protected]>
Cc: Michael Hennerich <[email protected]>
Signed-off-by: Lee Jones <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Guenter Roeck <[email protected]>
|
|
The shifting of the u8 integer data[3] by 24 bits to the left will
be promoted to a 32 bit signed int and then sign-extended to a
long. In the event that the top bit of data[3] is set then all
then all the upper 32 bits of a 64 bit long end up as also being
set because of the sign-extension. Fix this by casting data[3] to
a long before the shift.
Addresses-Coverity: ("Unintended sign extension")
Fixes: ce15cd2cee8b ("hwmon: add Corsair PSU HID controller driver")
Signed-off-by: Colin Ian King <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Guenter Roeck <[email protected]>
|
|
The Corsair digital power supplies of the series RMi, HXi and AXi include
a small micro-controller with a lot of sensors attached. The sensors can
be accessed by an USB connector from the outside.
This micro-controller provides the data by a simple proprietary USB HID
protocol. The data consist of temperatures, current and voltage levels,
power usage, uptimes, fan speed and some more. It is also possible to
configure the PSU (fan mode, mono/multi-rail, over current protection).
This driver provides access to the sensors/statistics of the RMi and HXi
series power supplies. It does not support configuring these devices,
because there would be many ways to misconfigure or even damage the PSU.
This patch adds:
- hwmon driver corsair-psu
- hwmon documentation
- updates MAINTAINERS
Signed-off-by: Wilken Gottwalt <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Guenter Roeck <[email protected]>
|
|
The only action currently performed in pmbus_do_remove() is removing the
debugfs hierarchy. We can schedule a devm action at probe time and remove
pmbus_do_remove() entirely from all pmbus drivers.
Signed-off-by: Bartosz Golaszewski <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
[groeck: Removed references to pmbus_do_remove from documentation]
Signed-off-by: Guenter Roeck <[email protected]>
|
|
Split the body of adt7470_update_device() into two helper functions
adt7470_update_sensors() and adt7470_update_limits(). Although neither
of the new helpers returns an error yet lay the groundwork for
propagating failures through to the sysfs readers.
Signed-off-by: Chris Packham <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Guenter Roeck <[email protected]>
|
|
The debugfs_create_dir() function never returns NULL. Normal users are
not supposed to check the return value so the correct fix is just to
delete this check.
In the case where the debugfs_create_dir() fails, the function returns
NULL. The other debugfs function check for NULL directory and handle
it.
Signed-off-by: Dan Carpenter <[email protected]>
Link: https://lore.kernel.org/r/20201022070659.GA2817762@mwanda
Signed-off-by: Guenter Roeck <[email protected]>
|
|
This code works okay but Smatch flagged it as a double free. I've
changed three things to make it more clear. 1) Remove the call to
free_capabilities() in acpi_power_meter_add(). This call is a no-op
because the capabilities have not been allocated yet. 2) Set "*str" to
NULL in free_capabilities() so that way the function can be called twice
in a row without leading to a double free. 3) Call free_capabilities()
in read_capabilities() instead of open coding the free.
Signed-off-by: Dan Carpenter <[email protected]>
Link: https://lore.kernel.org/r/20201007075148.GB2529578@mwanda
Signed-off-by: Guenter Roeck <[email protected]>
|
|
pm_runtime_get_sync will increment pm usage counter
even it failed. Forgetting to putting operation will
result in reference leak here. We fix it by replacing
it with pm_runtime_resume_and_get to keep usage counter
balanced. It depends on the mainline commit[PM: runtime:
Add pm_runtime_resume_and_get to deal with usagecounter].
Fixes: 323aeb0eb5d9a ("hwmon: (ina3221) Add PM runtime support")
Signed-off-by: Zhang Qilong <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Guenter Roeck <[email protected]>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Thomas Gleixner:
"Two more places which invoke tracing from RCU disabled regions in the
idle path.
Similar to the entry path the low level idle functions have to be
non-instrumentable"
* tag 'locking-urgent-2020-11-29' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
intel_idle: Fix intel_idle() vs tracing
sched/idle: Fix arch_cpu_idle() vs tracing
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"Two fixes for irqchip drivers:
- Save and restore the GICV3 ITS state unconditionally on
suspend/resume to handle firmware which fails to do so.
- Use the correct index into the fwspec parameters to read the irq
trigger type in the EXIU chip driver"
* tag 'irq-urgent-2020-11-29' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3-its: Unconditionally save/restore the ITS state on suspend
irqchip/exiu: Fix the index of fwspec for IRQ type
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI fixes from Borislav Petkov:
"More EFI fixes forwarded from Ard Biesheuvel:
- revert efivarfs kmemleak fix again - it was a false positive
- make CONFIG_EFI_EARLYCON depend on CONFIG_EFI explicitly so it does
not pull in other dependencies unnecessarily if CONFIG_EFI is not
set
- defer attempts to load SSDT overrides from EFI vars until after the
efivar layer is up"
* tag 'efi-urgent-for-v5.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi: EFI_EARLYCON should depend on EFI
efivarfs: revert "fix memory leak in efivarfs_create()"
efi/efivars: Set generic ops before loading SSDT
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
"A couple of urgent fixes which accumulated this last week:
- Two resctrl fixes to prevent refcount leaks when manipulating the
resctrl fs (Xiaochen Shen)
- Correct prctl(PR_GET_SPECULATION_CTRL) reporting (Anand K Mistry)
- A fix to not lose already seen MCE severity which determines
whether the machine can recover (Gabriele Paoloni)"
* tag 'x86_urgent_for_v5.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mce: Do not overwrite no_way_out if mce_end() fails
x86/speculation: Fix prctl() when spectre_v2_user={seccomp,prctl},ibpb
x86/resctrl: Add necessary kernfs_put() calls to prevent refcount leak
x86/resctrl: Remove superfluous kernfs_get() calls to prevent refcount leak
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
"I've collected a handful of fixes over the past few weeks:
- A fix to un-break the build-id argument to the vDSO build, which is
necessary for the LLVM linker.
- A fix to initialize the jump label subsystem, without which it (and
all the stuff that uses it) doesn't actually function.
- A fix to include <asm/barrier.h> from <vdso/processor.h>, without
which some drivers won't compile"
* tag 'riscv-for-linus-5.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
RISC-V: fix barrier() use in <vdso/processor.h>
RISC-V: Add missing jump label initialization
riscv: Explicitly specify the build id style in vDSO Makefile again
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- Remove unused OBJSIZE variable.
- Fix rootless deb-pkg build in a setgid directory.
* tag 'kbuild-fixes-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
builddeb: Fix rootless build in setuid/setgid directory
kbuild: remove unused OBJSIZE
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux
Pull perf tool fixes from Arnaldo Carvalho de Melo:
- Fix die_entrypc() when DW_AT_ranges DWARF attribute not available
- Cope with broken DWARF (missing DW_AT_declaration) generated by some
recent gcc versions
- Do not generate CGROUP metadata events when not asked to in 'perf
record'
- Use proper CPU for shadow stats in 'perf stat'
- Update copy of libbpf's hashmap.c, silencing tools/perf build warning
- Fix return value in 'perf diff'
* tag 'perf-tools-fixes-for-v5.10-2020-11-28' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
perf probe: Change function definition check due to broken DWARF
perf probe: Fix to die_entrypc() returns error correctly
perf stat: Use proper cpu for shadow stats
perf record: Synthesize cgroup events only if needed
perf diff: Fix error return value in __cmd_diff()
perf tools: Update copy of libbpf's hashmap.c
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / PHY driver fixes from Greg KH:
"Here are a few small USB and PHY driver fixes for 5.10-rc6. They
include:
- small PHY driver fixes to resolve reported issues
- USB quirks added for "broken" devices
- typec fixes for reported problems
- USB gadget fixes for small issues
Full details are in the shortlog, nothing major in here and all have
been in linux-next with no reported issues"
* tag 'usb-5.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: typec: stusb160x: fix power-opmode property with typec-power-opmode
USB: core: Change %pK for __user pointers to %px
USB: core: Fix regression in Hercules audio card
usb: gadget: Fix memleak in gadgetfs_fill_super
usb: gadget: f_midi: Fix memleak in f_midi_alloc
USB: quirks: Add USB_QUIRK_DISCONNECT_SUSPEND quirk for Lenovo A630Z TIO built-in usb-audio card
usb: typec: qcom-pmic-typec: fix builtin build errors
phy: mediatek: fix spelling mistake in Kconfig "veriosn" -> "version"
phy: qualcomm: Fix 28 nm Hi-Speed USB PHY OF dependency
phy: qualcomm: usb: Fix SuperSpeed PHY OF dependency
phy: intel: PHY_INTEL_KEEMBAY_EMMC should depend on ARCH_KEEMBAY
usb: cdns3: gadget: calculate TD_SIZE based on TD
usb: cdns3: gadget: initialize link_trb as NULL
phy: cpcap-usb: Use IRQF_ONESHOT
phy: qcom-qmp: Initialize another pointer to NULL
phy: tegra: xusb: Fix dangling pointer on probe failure
phy: usb: Fix incorrect clearing of tca_drv_sel bit in SETUP reg for 7211
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some small misc driver fixes for 5.10-rc6. They include:
- interconnect fixes for reported problems
- habanalabs bugfix for found issue when doing the switch fallthrough
patches
- MAINTAINERS file update for coresight reviewers/maintainers
All have been in linux-next with no reported issues"
* tag 'char-misc-5.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
MAINTAINERS: Adding help for coresight subsystem
habanalabs/gaudi: fix missing code in ECC handling
interconnect: fix memory trashing in of_count_icc_providers()
interconnect: qcom: qcs404: Remove GPU and display RPM IDs
interconnect: qcom: msm8916: Remove rpm-ids from non-RPM nodes
interconnect: qcom: msm8974: Don't boost the NoC rate during boot
interconnect: qcom: msm8974: Prevent integer overflow in rate
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic fix from Arnd Bergmann:
"Add correct MAX_POSSIBLE_PHYSMEM_BITS setting to asm-generic.
This is a single bugfix for a bug that Stefan Agner found on 32-bit
Arm, but that exists on several other architectures"
* tag 'asm-generic-fixes-5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
arch: pgtable: define MAX_POSSIBLE_PHYSMEM_BITS where needed
|