| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
While pci_irq_get_affinity should never fail for SMP kernel that
implement the affinity mapping, it will always return NULL in the
UP case, so provide a fallback mapping of all queues to CPU 0 in
that case.
Signed-off-by: Christoph Hellwig <[email protected]>
Cc: [email protected]
Reviewed-by: Omar Sandoval <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
Pull NVMe changes from Christoph:
"The fixes are getting really small now - two for FC, one for PCI, one
for the fabrics layer and one for the target."
|
|
The hardlockup detector on x86 uses a performance counter based on unhalted
CPU cycles and a periodic hrtimer. The hrtimer period is about 2/5 of the
performance counter period, so the hrtimer should fire 2-3 times before the
performance counter NMI fires. The NMI code checks whether the hrtimer
fired since the last invocation. If not, it assumess a hard lockup.
The calculation of those periods is based on the nominal CPU
frequency. Turbo modes increase the CPU clock frequency and therefore
shorten the period of the perf/NMI watchdog. With extreme Turbo-modes (3x
nominal frequency) the perf/NMI period is shorter than the hrtimer period
which leads to false positives.
A simple fix would be to shorten the hrtimer period, but that comes with
the side effect of more frequent hrtimer and softlockup thread wakeups,
which is not desired.
Implement a low pass filter, which checks the perf/NMI period against
kernel time. If the perf/NMI fires before 4/5 of the watchdog period has
elapsed then the event is ignored and postponed to the next perf/NMI.
That solves the problem and avoids the overhead of shorter hrtimer periods
and more frequent softlockup thread wakeups.
Fixes: 58687acba592 ("lockup_detector: Combine nmi_watchdog and softlockup detector")
Reported-and-tested-by: Kan Liang <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1708150931310.1886@nanos
|
|
irq_modify_status starts by clearing the trigger settings from
irq_data before applying the new settings, but doesn't restore them,
leaving them to IRQ_TYPE_NONE.
That's pretty confusing to the potential request_irq() that could
follow. Instead, snapshot the settings before clearing them, and restore
them if the irq_modify_status() invocation was not changing the trigger.
Fixes: 1e2a7d78499e ("irqdomain: Don't set type when mapping an IRQ")
Reported-and-tested-by: jeffy <[email protected]>
Signed-off-by: Marc Zyngier <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Cc: Jon Hunter <[email protected]>
Cc: [email protected]
Link: http://lkml.kernel.org/r/[email protected]
|
|
Commit b6a1d093f96b ("PM / Domains: Extend generic power domain
debugfs") now creates a debugfs directory for each genpd based on the
name of the genpd. Currently no name is given to the genpd created by
ti_sci_pm_domains driver so because of this we see a NULL pointer
dereferences when it is accessed on boot when the debugfs entry creation
is attempted.
Give the genpd a name before registering it to avoid this.
Fixes: 52835d59fc6c ("soc: ti: Add ti_sci_pm_domains driver")
Signed-off-by: Dave Gerlach <[email protected]>
Signed-off-by: Santosh Shilimkar <[email protected]>
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
Pull "i.MX fixes for 4.13, round 3" from Shawn Guo:
- Fix PCIe reset GPIO of imx6qdl-nitrogen6_som2 board, which was
a bad copy from nitrogen6_max device tree.
* tag 'imx-fixes-4.13-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6qdl-nitrogen6_som2: fix PCIe reset
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into fixes
Pull "Allwinner fixes for 4.13, round 2" from Chen-Yu Tsai:
Three fixes adding a missing alias for the Ethernet controller on A64
boards. One adding a missing interrupt for the pin controller.
* tag 'sunxi-fixes-for-4.13-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: allwinner: h5: fix pinctrl IRQs
arm64: allwinner: a64: sopine: add missing ethernet0 alias
arm64: allwinner: a64: pine64: add missing ethernet0 alias
arm64: allwinner: a64: bananapi-m64: add missing ethernet0 alias
|
|
attribute_groups are not supposed to change at runtime and none of the
groups is modified.
Mark the non-const structs as const.
[ tglx: Folded into one big patch ]
Signed-off-by: Arvind Yadav <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Cc: [email protected]
Cc: [email protected]
Link: http://lkml.kernel.org/r/[email protected]
|
|
Jason's irqchip tree does not seem to have been updated for many months
now, remove it from the list of trees to avoid any possible confusion.
Jason says:
"Unfortunately, when I have time for irqchip, I don't always have the
time to properly follow up with pull-requests. So, for the time being,
I'll stick to reviewing as I can."
Signed-off-by: Florian Fainelli <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Acked-by: Jason Cooper <[email protected]>
Cc: [email protected]
Link: http://lkml.kernel.org/r/[email protected]
|
|
The commit d42fe63d5839 ("ALSA: emu10k1: Get rid of set_fs() usage")
converted the user-space copy hack with set_fs() to the direct
memcpy(), but one place was forgotten. This resulted in the error
from snd_emu10k1_init_efx(), eventually failed to load the driver.
Fix the missing piece.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=196687
Fixes: d42fe63d5839 ("ALSA: emu10k1: Get rid of set_fs() usage")
Signed-off-by: Takashi Iwai <[email protected]>
|
|
We need the ASM_UNREACHABLE() macro for a dependent patch.
Signed-off-by: Ingo Molnar <[email protected]>
|
|
Add DSD support for new Amanero Combo384 firmware version with a new
PID. This firmware uses DSD_U32_BE.
Fixes: 3eff682d765b ("ALSA: usb-audio: Support both DSD LE/BE Amanero firmware versions")
Signed-off-by: Jussi Laako <[email protected]>
Cc: <[email protected]>
Signed-off-by: Takashi Iwai <[email protected]>
|
|
Fixes: 920d13a884 ("nvme-pci: factor out the cqe reading mechanics from __nvme_process_cq")
Reported-by: Jens Axboe <[email protected]>
Signed-off-by: Keith Busch <[email protected]>
Signed-off-by: Christoph Hellwig <[email protected]>
|
|
Previous value was a bad copy of nitrogen6_max device tree.
Signed-off-by: Gary Bisson <[email protected]>
Fixes: 3faa1bb2e89c ("ARM: dts: imx: add Boundary Devices Nitrogen6_SOM2 support")
Cc: <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Seems to be slowing down nicely, just one amdgpu fix, and a bunch of
i915 fixes"
* tag 'drm-fixes-for-v4.13-rc6' of git://people.freedesktop.org/~airlied/linux:
drm/amdgpu: save list length when fence is signaled
drm/i915: Avoid the gpu reset vs. modeset deadlock
drm/i915: Suppress switch_mm emission between the same aliasing_ppgtt
drm/i915: Return correct EDP voltage swing table for 0.85V
drm/i915/cnl: Add slice and subslice information to debugfs.
drm/i915: Perform an invalidate prior to executing golden renderstate
drm/i915: remove unused function declaration
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix two issues related to exposing the current CPU frequency to
user space on x86.
Specifics:
- Disable interrupts around reading IA32_APERF and IA32_MPERF in
aperfmperf_snapshot_khz() (introduced recently) to avoid excessive
delays between the reads that may result from interrupt handling
(Doug Smythies).
- Fix the computation of the CPU frequency to be reported through the
pstate_sample tracepoint in intel_pstate (Doug Smythies)"
* tag 'pm-4.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: x86: Disable interrupts during MSRs reading
cpufreq: intel_pstate: report correct CPU frequencies during trace
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elan_i2c - Add antoher Lenovo ACPI ID for upcoming Lenovo NB
Input: elan_i2c - add ELAN0608 to the ACPI table
Input: trackpoint - assume 3 buttons when buttons detection fails
|
|
into drm-fixes
single amdgpu fix.
* 'drm-fixes-4.13' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: save list length when fence is signaled
|
|
git://anongit.freedesktop.org/git/drm-intel into drm-fixes
drm/i915 fixes for v4.13-rc6
"Chris' "drm/i915: Perform an invalidate prior to executing golden renderstate" and Daniel's
"drm/i915: Avoid the gpu reset vs. modeset deadlock" seem like the most important ones.
* tag 'drm-intel-fixes-2017-08-16' of git://anongit.freedesktop.org/git/drm-intel:
drm/i915: Avoid the gpu reset vs. modeset deadlock
drm/i915: Suppress switch_mm emission between the same aliasing_ppgtt
drm/i915: Return correct EDP voltage swing table for 0.85V
drm/i915/cnl: Add slice and subslice information to debugfs.
drm/i915: Perform an invalidate prior to executing golden renderstate
drm/i915: remove unused function declaration
|
|
If we fail a mount on account of cow recovery errors, it's possible that
a previous quotacheck left some dquots in memory. The bailout clause of
xfs_mountfs forgets to purge these, and so we leak them. Fix that.
Signed-off-by: Darrick J. Wong <[email protected]>
Reviewed-by: Brian Foster <[email protected]>
|
|
Way back when we established inode block-map redo log items, it was
discovered that we needed to prevent the VFS from evicting inodes during
log recovery because any given inode might be have bmap redo items to
replay even if the inode has no link count and is ultimately deleted,
and any eviction of an unlinked inode causes the inode to be truncated
and freed too early.
To make this possible, we set MS_ACTIVE so that inodes would not be torn
down immediately upon release. Unfortunately, this also results in the
quota inodes not being released at all if a later part of the mount
process should fail, because we never reclaim the inodes. So, set
MS_ACTIVE right before we do the last part of log recovery and clear it
immediately after we finish the log recovery so that everything
will be torn down properly if we abort the mount.
Fixes: 17c12bcd30 ("xfs: when replaying bmap operations, don't let unlinked inodes get reaped")
Signed-off-by: Darrick J. Wong <[email protected]>
Reviewed-by: Brian Foster <[email protected]>
|
|
* intel_pstate-fix:
cpufreq: intel_pstate: report correct CPU frequencies during trace
* cpufreq-x86-fix:
cpufreq: x86: Disable interrupts during MSRs reading
|
|
Commit 2a5708409e4e (ACPI / EC: Fix a gap that ECDT EC cannot handle
EC events) introduced acpi_ec_ecdt_start(), but that function is
invoked before acpi_ec_query_init(), which is too early. This causes
the kernel to crash if an EC event occurs after boot, when ec_query_wq
is not valid:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000102
...
Workqueue: events acpi_ec_event_handler
task: ffff9f539790dac0 task.stack: ffffb437c0e10000
RIP: 0010:__queue_work+0x32/0x430
Normally, the DSDT EC should always be valid, so acpi_ec_ecdt_start()
is actually a no-op in the majority of cases. However, commit
c712bb58d827 (ACPI / EC: Add support to skip boot stage DSDT probe)
caused the probing of the DSDT EC as the "boot EC" to be skipped when
the ECDT EC is valid and uncovered the bug.
Fix this issue by invoking acpi_ec_ecdt_start() after acpi_ec_query_init()
in acpi_ec_init().
Link: https://jira01.devtools.intel.com/browse/LCK-4348
Fixes: 2a5708409e4e (ACPI / EC: Fix a gap that ECDT EC cannot handle EC events)
Fixes: c712bb58d827 (ACPI / EC: Add support to skip boot stage DSDT probe)
Reported-by: Wang Wendy <[email protected]>
Tested-by: Feng Chenzhou <[email protected]>
Signed-off-by: Lv Zheng <[email protected]>
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
- Fix PCI memory bar assignments with 64-bit kernels on machines with
Dino/Cujo PCI chipsets. This makes PCI graphic cards work on such
machines (from Thomas Bogendoerfer).
- Fix documentation to be more clear about the difference between %pF
and %pS printk format usage. There are still many places in the
kernel which have it wrong (from Petr Mladek, Sergey Senozhatsky &
me).
* 'parisc-4.13-5' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
printk-formats.txt: Better describe the difference between %pS and %pF
parisc: pci memory bar assignment fails with 64bit kernels on dino/cujo
|
|
The sysctl documentation states that the JIT is only available on
x86_64, which is no longer correct.
Update the list, and break it out to indicate which architectures
support the cBPF JIT (via HAVE_CBPF_JIT) or the eBPF JIT
(HAVE_EBPF_JIT).
Signed-off-by: Michael Ellerman <[email protected]>
Acked-by: Daniel Borkmann <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Only print the specified options that are not recognized, instead
of the whole list of options.
Signed-off-by: Christoph Hellwig <[email protected]>
Reviewed-by: Max Gurtovoy <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Pull quota fix from Jan Kara:
"A fix of a check for quota limit"
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
quota: correct space limit check
|
|
Christian Brauner reported that if you use the TIOCGPTPEER ioctl() to
get a slave pty file descriptor, the resulting file descriptor doesn't
look right in /proc/<pid>/fd/<fd>. In particular, he wanted to use
readlink() on /proc/self/fd/<fd> to get the pathname of the slave pty
(basically implementing "ptsname{_r}()").
The reason for that was that we had generated the wrong 'struct path'
when we create the pty in ptmx_open().
In particular, the dentry was correct, but the vfsmount pointed to the
mount of the ptmx node. That _can_ be correct - in case you use
"/dev/pts/ptmx" to open the master - but usually is not. The normal
case is to use /dev/ptmx, which then looks up the pts/ directory, and
then the vfsmount of the ptmx node is obviously the /dev directory, not
the /dev/pts/ directory.
We actually did have the right vfsmount available, but in the wrong
place (it gets looked up in 'devpts_acquire()' when we get a reference
to the pts filesystem), and so ptmx_open() used the wrong mnt pointer.
The end result of this confusion was that the pty worked fine, but when
if you did TIOCGPTPEER to get the slave side of the pty, end end result
would also work, but have that dodgy 'struct path'.
And then when doing "d_path()" on to get the pathname, the vfsmount
would not match the root of the pts directory, and d_path() would return
an empty pathname thinking that the entry had escaped a bind mount into
another mount.
This fixes the problem by making devpts_acquire() return the vfsmount
for the pts filesystem, allowing ptmx_open() to trivially just use the
right mount for the pts dentry, and create the proper 'struct path'.
Reported-by: Christian Brauner <[email protected]>
Cc: Al Viro <[email protected]>
Acked-by: Eric Biederman <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
C-Media devices (at least some models) mute the playback stream when
volumes are set to the minimum value. But this isn't informed via TLV
and the user-space, typically PulseAudio, gets confused as if it's
still played in a low volume.
This patch adds the new flag, min_mute, to struct usb_mixer_elem_info
for indicating that the mixer element is with the minimum-mute volume.
This flag is set for known C-Media devices in
snd_usb_mixer_fu_apply_quirk() in turn.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=196669
Cc: <[email protected]>
Signed-off-by: Takashi Iwai <[email protected]>
|
|
CONFIG_LOCKDEP_COMPLETIONS truly non-interactive
The syntax to turn Kconfig options into non-interactive ones is to not offer
interactive prompt help texts. Remove them.
Cc: Boqun Feng <[email protected]>
Cc: Byungchul Park <[email protected]>
Cc: Lai Jiangshan <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Tejun Heo <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: [email protected]
Signed-off-by: Ingo Molnar <[email protected]>
|
|
With the new lockdep crossrelease feature, which checks completions usage,
a false positive is reported in the workqueue code:
> Worker A : acquired of wfc.work -> wait for cpu_hotplug_lock to be released
> Task B : acquired of cpu_hotplug_lock -> wait for lock#3 to be released
> Task C : acquired of lock#3 -> wait for completion of barr->done
> (Task C is in lru_add_drain_all_cpuslocked())
> Worker D : wait for wfc.work to be released -> will complete barr->done
Such a dead lock can not happen because Task C's barr->done and Worker D's
barr->done can not be the same instance.
The reason of this false positive is we initialize all wq_barrier::done
at insert_wq_barrier() via init_completion(), which makes them belong to
the same lock class, therefore, impossible circles are reported.
To fix this, explicitly initialize the lockdep map for wq_barrier::done
in insert_wq_barrier(), so that the lock class key of wq_barrier::done
is a subkey of the corresponding work_struct, as a result we won't build
a dependency between a wq_barrier with a unrelated work, and we can
differ wq barriers based on the related works, so the false positive
above is avoided.
Also define the empty lockdep_init_map_crosslock() for !CROSSRELEASE
to make the code simple and away from unnecessary #ifdefs.
Reported-by: Ingo Molnar <[email protected]>
Signed-off-by: Boqun Feng <[email protected]>
Cc: Byungchul Park <[email protected]>
Cc: Lai Jiangshan <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Tejun Heo <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Ingo Molnar <[email protected]>
|
|
'complete' is an adjective and LOCKDEP_COMPLETE sounds like 'lockdep is complete',
so pick a better name that uses a noun.
Signed-off-by: Byungchul Park <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: [email protected]
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Ingo Molnar <[email protected]>
|
|
Lockdep doesn't have to be made to work with crossrelease and just works
with them. Reword the title so that what the option does is clear.
Signed-off-by: Byungchul Park <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: [email protected]
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Ingo Molnar <[email protected]>
|
|
Crossrelease support added the CONFIG_LOCKDEP_CROSSRELEASE and CONFIG_LOCKDEP_COMPLETE
options. It makes little sense to enable them when PROVE_LOCKING is disabled.
Make them non-interative options and part of PROVE_LOCKING to simplify the UI.
Signed-off-by: Byungchul Park <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: [email protected]
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Ingo Molnar <[email protected]>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Pull "Fourth Round of Renesas ARM Based SoC Fixes for v4.13" from Simon Horman:
* Avoid audio_clkout naming conflict for salvator boards using
Renesas R-Car Gen 3 SoCs
Morimoto-san says "The clock name of "audio_clkout" is used by the
Renesas sound driver. This duplicated naming breaks its clock
registering/unregistering. Especially when unbind/bind it can't handle
clkout correctly. This patch renames "audio_clkout" to "audio-clkout" to
avoid the naming conflict."
* tag 'renesas-fixes4-for-v4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: renesas: salvator-common: avoid audio_clkout naming conflict
|
|
This implements refcount_t overflow protection on x86 without a noticeable
performance impact, though without the fuller checking of REFCOUNT_FULL.
This is done by duplicating the existing atomic_t refcount implementation
but with normally a single instruction added to detect if the refcount
has gone negative (e.g. wrapped past INT_MAX or below zero). When detected,
the handler saturates the refcount_t to INT_MIN / 2. With this overflow
protection, the erroneous reference release that would follow a wrap back
to zero is blocked from happening, avoiding the class of refcount-overflow
use-after-free vulnerabilities entirely.
Only the overflow case of refcounting can be perfectly protected, since
it can be detected and stopped before the reference is freed and left to
be abused by an attacker. There isn't a way to block early decrements,
and while REFCOUNT_FULL stops increment-from-zero cases (which would
be the state _after_ an early decrement and stops potential double-free
conditions), this fast implementation does not, since it would require
the more expensive cmpxchg loops. Since the overflow case is much more
common (e.g. missing a "put" during an error path), this protection
provides real-world protection. For example, the two public refcount
overflow use-after-free exploits published in 2016 would have been
rendered unexploitable:
http://perception-point.io/2016/01/14/analysis-and-exploitation-of-a-linux-kernel-vulnerability-cve-2016-0728/
http://cyseclabs.com/page?n=02012016
This implementation does, however, notice an unchecked decrement to zero
(i.e. caller used refcount_dec() instead of refcount_dec_and_test() and it
resulted in a zero). Decrements under zero are noticed (since they will
have resulted in a negative value), though this only indicates that a
use-after-free may have already happened. Such notifications are likely
avoidable by an attacker that has already exploited a use-after-free
vulnerability, but it's better to have them reported than allow such
conditions to remain universally silent.
On first overflow detection, the refcount value is reset to INT_MIN / 2
(which serves as a saturation value) and a report and stack trace are
produced. When operations detect only negative value results (such as
changing an already saturated value), saturation still happens but no
notification is performed (since the value was already saturated).
On the matter of races, since the entire range beyond INT_MAX but before
0 is negative, every operation at INT_MIN / 2 will trap, leaving no
overflow-only race condition.
As for performance, this implementation adds a single "js" instruction
to the regular execution flow of a copy of the standard atomic_t refcount
operations. (The non-"and_test" refcount_dec() function, which is uncommon
in regular refcount design patterns, has an additional "jz" instruction
to detect reaching exactly zero.) Since this is a forward jump, it is by
default the non-predicted path, which will be reinforced by dynamic branch
prediction. The result is this protection having virtually no measurable
change in performance over standard atomic_t operations. The error path,
located in .text.unlikely, saves the refcount location and then uses UD0
to fire a refcount exception handler, which resets the refcount, handles
reporting, and returns to regular execution. This keeps the changes to
.text size minimal, avoiding return jumps and open-coded calls to the
error reporting routine.
Example assembly comparison:
refcount_inc() before:
.text:
ffffffff81546149: f0 ff 45 f4 lock incl -0xc(%rbp)
refcount_inc() after:
.text:
ffffffff81546149: f0 ff 45 f4 lock incl -0xc(%rbp)
ffffffff8154614d: 0f 88 80 d5 17 00 js ffffffff816c36d3
...
.text.unlikely:
ffffffff816c36d3: 48 8d 4d f4 lea -0xc(%rbp),%rcx
ffffffff816c36d7: 0f ff (bad)
These are the cycle counts comparing a loop of refcount_inc() from 1
to INT_MAX and back down to 0 (via refcount_dec_and_test()), between
unprotected refcount_t (atomic_t), fully protected REFCOUNT_FULL
(refcount_t-full), and this overflow-protected refcount (refcount_t-fast):
2147483646 refcount_inc()s and 2147483647 refcount_dec_and_test()s:
cycles protections
atomic_t 82249267387 none
refcount_t-fast 82211446892 overflow, untested dec-to-zero
refcount_t-full 144814735193 overflow, untested dec-to-zero, inc-from-zero
This code is a modified version of the x86 PAX_REFCOUNT atomic_t
overflow defense from the last public patch of PaX/grsecurity, based
on my understanding of the code. Changes or omissions from the original
code are mine and don't reflect the original grsecurity/PaX code. Thanks
to PaX Team for various suggestions for improvement for repurposing this
code to be a refcount-only protection.
Signed-off-by: Kees Cook <[email protected]>
Reviewed-by: Josh Poimboeuf <[email protected]>
Cc: Alexey Dobriyan <[email protected]>
Cc: Andrew Morton <[email protected]>
Cc: Arnd Bergmann <[email protected]>
Cc: Christoph Hellwig <[email protected]>
Cc: David S. Miller <[email protected]>
Cc: Davidlohr Bueso <[email protected]>
Cc: Elena Reshetova <[email protected]>
Cc: Eric Biggers <[email protected]>
Cc: Eric W. Biederman <[email protected]>
Cc: Greg KH <[email protected]>
Cc: Hans Liljestrand <[email protected]>
Cc: James Bottomley <[email protected]>
Cc: Jann Horn <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: Manfred Spraul <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Rik van Riel <[email protected]>
Cc: Serge E. Hallyn <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: linux-arch <[email protected]>
Link: http://lkml.kernel.org/r/20170815161924.GA133115@beast
Signed-off-by: Ingo Molnar <[email protected]>
|
|
Historically, DMA masks have suffered some ambiguity between whether
they represent the range of physical memory a device can access, or the
address bits a device is capable of driving, particularly since on many
platforms the two are equivalent. Whilst there are some stragglers left
(dma_max_pfn(), I'm looking at you...), the majority of DMA code has
been cleaned up to follow the latter definition, not least since it is
the only one which makes sense once IOMMUs are involved.
In this respect, of_dma_configure() has always done the wrong thing in
how it generates initial masks based on "dma-ranges". Although rounding
down did not affect the TI Keystone platform where dma_addr + size is
already a power of two, in any other case it results in a mask which is
at best unnecessarily constrained and at worst unusable.
BCM2837 illustrates the problem nicely, where we have a DMA base of 3GB
and a size of 1GB - 16MB, giving dma_addr + size = 0xff000000 and a
resultant mask of 0x7fffffff, which is then insufficient to even cover
the necessary offset, effectively making all DMA addresses out-of-range.
This has been hidden until now (mostly because we don't yet prevent
drivers from simply overwriting this initial mask later upon probe), but
due to recent changes elsewhere now shows up as USB being broken on
Raspberry Pi 3.
Make it right by rounding up instead of down, such that the mask
correctly correctly describes all possisble bits the device needs to
emit.
Fixes: 9a6d7298b083 ("of: Calculate device DMA masks based on DT dma-range size")
Reported-by: Stefan Wahren <[email protected]>
Reported-by: Andreas Färber <[email protected]>
Reported-by: Hans Verkuil <[email protected]>
Signed-off-by: Robin Murphy <[email protected]>
Acked-by: Rob Herring <[email protected]>
Signed-off-by: Christoph Hellwig <[email protected]>
|
|
__startup_64() is normally using fixup_pointer() to access globals in a
position-independent fashion. However 'next_early_pgt' was accessed
directly, which wasn't guaranteed to work.
Luckily GCC was generating a R_X86_64_PC32 PC-relative relocation for
'next_early_pgt', but Clang emitted a R_X86_64_32S, which led to
accessing invalid memory and rebooting the kernel.
Signed-off-by: Alexander Potapenko <[email protected]>
Acked-by: Kirill A. Shutemov <[email protected]>
Cc: Dmitry Vyukov <[email protected]>
Cc: Kirill A. Shutemov <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: Michael Davidson <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Fixes: c88d71508e36 ("x86/boot/64: Rewrite startup_64() in C")
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Ingo Molnar <[email protected]>
|
|
There were 2 statics introduced that were bogus. Removed the static
designations.
Signed-off-by: James Smart <[email protected]>
Signed-off-by: Christoph Hellwig <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"A couple of minor fixes (st, ses) and some bigger driver fixes for
qla2xxx (crash triggered by fw dump) and ipr (lockdep problems with
mq)"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ses: Fix wrong page error
scsi: ipr: Fix scsi-mq lockdep issue
scsi: st: fix blk_get_queue usage
scsi: qla2xxx: Fix system crash while triggering FW dump
|
|
If nud_state is not valid then call neigh_event_send() to update MAC
address.
Signed-off-by: Varun Prakash <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
Defaulting to scsi-mq in 4.13-rc has shown various regressions
on setups that we didn't previously consider. Fixes for them are
in progress, but too invasive to make it in this cycle. So for
now revert the commit that defaults to blk-mq for SCSI. For 4.14
we'll plan to try again with these fixes.
This reverts commit 5c279bd9e40624f4ab6e688671026d6005b066fa.
Signed-off-by: Christoph Hellwig <[email protected]>
Reviewed-by: Hannes Reinecke <[email protected]>
Reviewed-by: Bart Van Assche <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
Releasing a zone write lock only when the write commnand that acquired
the lock completes can cause deadlocks due to potential command
reordering if the lock owning request is requeued and not executed. This
problem exists only with the scsi-mq path as, unlike the legacy path,
requests are moved out of the dispatch queue before being prepared and
so before locking a zone for a write command.
Since sd_uninit_cmnd() is now always called when a request is requeued,
call sd_zbc_write_unlock_zone() from that function for write requests
that acquired a zone lock instead of from sd_done(). Acquisition of a zone
lock by a write command is indicated using the new command
flag SCMD_ZONE_WRITE_LOCK.
Signed-off-by: Damien Le Moal <[email protected]>
Reviewed-by: Christoph Hellwig <[email protected]>
Reviewed-by: Bart Van Assche <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
We terminate the aac_get_name_resp on a byte that is outside the bounds
of the structure. Extend the return response by one byte to remove the
out of bounds reference.
Fixes: b836439faf04 ("aacraid: 4KB sector support")
Reported-by: Dan Carpenter <[email protected]>
Signed-off-by: David Carroll <[email protected]>
Signed-off-by: Raghava Aditya Renukunta <[email protected]>
Reviewed-by: Bart Van Assche <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
Fail probe if FCoE capability is not enabled in the firmware.
Signed-off-by: Varun Prakash <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
megasas_mgmt_info.max_index has increased by 1 before megasas_io_attach,
if megasas_io_attach return error, then goto fail_io_attach,
megasas_mgmt_info.instance has a wrong index here. So first reduce
max_index and then set that instance to NULL.
Signed-off-by: weiping zhang <[email protected]>
Acked-by: Sumit Saxena <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit
Pull audit fixes from Paul Moore:
"Two small fixes to the audit code, both explained well in the
respective patch descriptions, but the quick summary is one
use-after-free fix, and one silly fanotify notification flag fix"
* tag 'audit-pr-20170816' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit:
audit: Receive unmount event
audit: Fix use after free in audit_remove_watch_rule()
|
|
While working on yet another syzkaller report, I found
that our IP_MAX_MTU enforcements were not properly done.
gcc seems to reload dev->mtu for min(dev->mtu, IP_MAX_MTU), and
final result can be bigger than IP_MAX_MTU :/
This is a problem because device mtu can be changed on other cpus or
threads.
While this patch does not fix the issue I am working on, it is
probably worth addressing it.
Signed-off-by: Eric Dumazet <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
As found by syzkaller, malicious users can set whatever tx_queue_len
on a tun device and eventually crash the kernel.
Lets remove the ALIGN(XXX, SMP_CACHE_BYTES) thing since a small
ring buffer is not fast anyway.
Fixes: 2e0ab8ca83c1 ("ptr_ring: array based FIFO for pointers")
Signed-off-by: Eric Dumazet <[email protected]>
Reported-by: Dmitry Vyukov <[email protected]>
Cc: Michael S. Tsirkin <[email protected]>
Cc: Jason Wang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
syszkaller team reported another problem in DCCP [1]
Problem here is that the structure holding RTO timer
(ccid2_hc_tx_rto_expire() handler) is freed too soon.
We can not use del_timer_sync() to cancel the timer
since this timer wants to grab socket lock (that would risk a dead lock)
Solution is to defer the freeing of memory when all references to
the socket were released. Socket timers do own a reference, so this
should fix the issue.
[1]
==================================================================
BUG: KASAN: use-after-free in ccid2_hc_tx_rto_expire+0x51c/0x5c0 net/dccp/ccids/ccid2.c:144
Read of size 4 at addr ffff8801d2660540 by task kworker/u4:7/3365
CPU: 1 PID: 3365 Comm: kworker/u4:7 Not tainted 4.13.0-rc4+ #3
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: events_unbound call_usermodehelper_exec_work
Call Trace:
<IRQ>
__dump_stack lib/dump_stack.c:16 [inline]
dump_stack+0x194/0x257 lib/dump_stack.c:52
print_address_description+0x73/0x250 mm/kasan/report.c:252
kasan_report_error mm/kasan/report.c:351 [inline]
kasan_report+0x24e/0x340 mm/kasan/report.c:409
__asan_report_load4_noabort+0x14/0x20 mm/kasan/report.c:429
ccid2_hc_tx_rto_expire+0x51c/0x5c0 net/dccp/ccids/ccid2.c:144
call_timer_fn+0x233/0x830 kernel/time/timer.c:1268
expire_timers kernel/time/timer.c:1307 [inline]
__run_timers+0x7fd/0xb90 kernel/time/timer.c:1601
run_timer_softirq+0x21/0x80 kernel/time/timer.c:1614
__do_softirq+0x2f5/0xba3 kernel/softirq.c:284
invoke_softirq kernel/softirq.c:364 [inline]
irq_exit+0x1cc/0x200 kernel/softirq.c:405
exiting_irq arch/x86/include/asm/apic.h:638 [inline]
smp_apic_timer_interrupt+0x76/0xa0 arch/x86/kernel/apic/apic.c:1044
apic_timer_interrupt+0x93/0xa0 arch/x86/entry/entry_64.S:702
RIP: 0010:arch_local_irq_enable arch/x86/include/asm/paravirt.h:824 [inline]
RIP: 0010:__raw_write_unlock_irq include/linux/rwlock_api_smp.h:267 [inline]
RIP: 0010:_raw_write_unlock_irq+0x56/0x70 kernel/locking/spinlock.c:343
RSP: 0018:ffff8801cd50eaa8 EFLAGS: 00000286 ORIG_RAX: ffffffffffffff10
RAX: dffffc0000000000 RBX: ffffffff85a090c0 RCX: 0000000000000006
RDX: 1ffffffff0b595f3 RSI: 1ffff1003962f989 RDI: ffffffff85acaf98
RBP: ffff8801cd50eab0 R08: 0000000000000001 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: ffff8801cc96ea60
R13: dffffc0000000000 R14: ffff8801cc96e4c0 R15: ffff8801cc96e4c0
</IRQ>
release_task+0xe9e/0x1a40 kernel/exit.c:220
wait_task_zombie kernel/exit.c:1162 [inline]
wait_consider_task+0x29b8/0x33c0 kernel/exit.c:1389
do_wait_thread kernel/exit.c:1452 [inline]
do_wait+0x441/0xa90 kernel/exit.c:1523
kernel_wait4+0x1f5/0x370 kernel/exit.c:1665
SYSC_wait4+0x134/0x140 kernel/exit.c:1677
SyS_wait4+0x2c/0x40 kernel/exit.c:1673
call_usermodehelper_exec_sync kernel/kmod.c:286 [inline]
call_usermodehelper_exec_work+0x1a0/0x2c0 kernel/kmod.c:323
process_one_work+0xbf3/0x1bc0 kernel/workqueue.c:2097
worker_thread+0x223/0x1860 kernel/workqueue.c:2231
kthread+0x35e/0x430 kernel/kthread.c:231
ret_from_fork+0x2a/0x40 arch/x86/entry/entry_64.S:425
Allocated by task 21267:
save_stack_trace+0x16/0x20 arch/x86/kernel/stacktrace.c:59
save_stack+0x43/0xd0 mm/kasan/kasan.c:447
set_track mm/kasan/kasan.c:459 [inline]
kasan_kmalloc+0xad/0xe0 mm/kasan/kasan.c:551
kasan_slab_alloc+0x12/0x20 mm/kasan/kasan.c:489
kmem_cache_alloc+0x127/0x750 mm/slab.c:3561
ccid_new+0x20e/0x390 net/dccp/ccid.c:151
dccp_hdlr_ccid+0x27/0x140 net/dccp/feat.c:44
__dccp_feat_activate+0x142/0x2a0 net/dccp/feat.c:344
dccp_feat_activate_values+0x34e/0xa90 net/dccp/feat.c:1538
dccp_rcv_request_sent_state_process net/dccp/input.c:472 [inline]
dccp_rcv_state_process+0xed1/0x1620 net/dccp/input.c:677
dccp_v4_do_rcv+0xeb/0x160 net/dccp/ipv4.c:679
sk_backlog_rcv include/net/sock.h:911 [inline]
__release_sock+0x124/0x360 net/core/sock.c:2269
release_sock+0xa4/0x2a0 net/core/sock.c:2784
inet_wait_for_connect net/ipv4/af_inet.c:557 [inline]
__inet_stream_connect+0x671/0xf00 net/ipv4/af_inet.c:643
inet_stream_connect+0x58/0xa0 net/ipv4/af_inet.c:682
SYSC_connect+0x204/0x470 net/socket.c:1642
SyS_connect+0x24/0x30 net/socket.c:1623
entry_SYSCALL_64_fastpath+0x1f/0xbe
Freed by task 3049:
save_stack_trace+0x16/0x20 arch/x86/kernel/stacktrace.c:59
save_stack+0x43/0xd0 mm/kasan/kasan.c:447
set_track mm/kasan/kasan.c:459 [inline]
kasan_slab_free+0x71/0xc0 mm/kasan/kasan.c:524
__cache_free mm/slab.c:3503 [inline]
kmem_cache_free+0x77/0x280 mm/slab.c:3763
ccid_hc_tx_delete+0xc5/0x100 net/dccp/ccid.c:190
dccp_destroy_sock+0x1d1/0x2b0 net/dccp/proto.c:225
inet_csk_destroy_sock+0x166/0x3f0 net/ipv4/inet_connection_sock.c:833
dccp_done+0xb7/0xd0 net/dccp/proto.c:145
dccp_time_wait+0x13d/0x300 net/dccp/minisocks.c:72
dccp_rcv_reset+0x1d1/0x5b0 net/dccp/input.c:160
dccp_rcv_state_process+0x8fc/0x1620 net/dccp/input.c:663
dccp_v4_do_rcv+0xeb/0x160 net/dccp/ipv4.c:679
sk_backlog_rcv include/net/sock.h:911 [inline]
__sk_receive_skb+0x33e/0xc00 net/core/sock.c:521
dccp_v4_rcv+0xef1/0x1c00 net/dccp/ipv4.c:871
ip_local_deliver_finish+0x2e2/0xba0 net/ipv4/ip_input.c:216
NF_HOOK include/linux/netfilter.h:248 [inline]
ip_local_deliver+0x1ce/0x6d0 net/ipv4/ip_input.c:257
dst_input include/net/dst.h:477 [inline]
ip_rcv_finish+0x8db/0x19c0 net/ipv4/ip_input.c:397
NF_HOOK include/linux/netfilter.h:248 [inline]
ip_rcv+0xc3f/0x17d0 net/ipv4/ip_input.c:488
__netif_receive_skb_core+0x19af/0x33d0 net/core/dev.c:4417
__netif_receive_skb+0x2c/0x1b0 net/core/dev.c:4455
process_backlog+0x203/0x740 net/core/dev.c:5130
napi_poll net/core/dev.c:5527 [inline]
net_rx_action+0x792/0x1910 net/core/dev.c:5593
__do_softirq+0x2f5/0xba3 kernel/softirq.c:284
The buggy address belongs to the object at ffff8801d2660100
which belongs to the cache ccid2_hc_tx_sock of size 1240
The buggy address is located 1088 bytes inside of
1240-byte region [ffff8801d2660100, ffff8801d26605d8)
The buggy address belongs to the page:
page:ffffea0007499800 count:1 mapcount:0 mapping:ffff8801d2660100 index:0x0 compound_mapcount: 0
flags: 0x200000000008100(slab|head)
raw: 0200000000008100 ffff8801d2660100 0000000000000000 0000000100000005
raw: ffffea00075271a0 ffffea0007538820 ffff8801d3aef9c0 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff8801d2660400: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff8801d2660480: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff8801d2660500: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff8801d2660580: fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc fc
ffff8801d2660600: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
==================================================================
Signed-off-by: Eric Dumazet <[email protected]>
Reported-by: Dmitry Vyukov <[email protected]>
Cc: Gerrit Renker <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|