| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Current adg.c doesn't assume that requested clock out divide condition
doesn't match. In such case, it will indicate strange message, and will
register NULL clock, etc. It is just a DT setting miss, but is
confusable. This patch check all conditions for it.
Reported-by: Vincenzo De Michele <[email protected]>
Signed-off-by: Kuninori Morimoto <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Basically Renesas sound ADG is assuming that it has accurately
divisible input clock. But sometimes / some board might not have it.
The clk_i from CPG is used for such case. It can't calculate accurate
division, but can be used as approximate rate.
This patch enable clk_i for such case.
Signed-off-by: Kuninori Morimoto <[email protected]>
Acked-by: Adnan Ali <[email protected]>
Tested-by: Vincenzo De Michele <[email protected]>
Tested-by: Patrick Keil <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Since the hardware may be designed as a single-ended input, the headset mic
record only supports single-ended input on the left side. This patch
will enhance microphone recording performance for single-end.
Signed-off-by: Seven Lee <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Add input with single-ended control.
Signed-off-by: Seven Lee <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
This codec was used by the deleted S3C board
sound/soc/samsung/s3c24xx_uda134x.c.
Fixes: 503278c12701 ("ASoC: samsung: remove unused drivers")
Signed-off-by: Linus Walleij <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
DSP_SW_INTR_STAT_OFFSET is a common interrupt register which will be
accessed by both ACP firmware and driver. This register contains register
bits corresponds to host to dsp interrupts and vice versa.
when dsp to host interrupt is reported, only clear dsp to host
interrupt bit in DSP_SW_INTR_STAT_OFFSET.
Fixes: 2e7c6652f9b8 ("ASoC: SOF: amd: Fix for handling spurious interrupts from DSP")
Signed-off-by: Vijendar Mukunda <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Due to scratch memory persistence, Once the DSP panic is reported, need to
clear the panic mask after handling DSP panic. Otherwise, It results in DSP
panic on next reboot.
Signed-off-by: Vijendar Mukunda <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Few AMD platforms require ACP ACLK as clock source.
Add conditional check for clock mux selection register for
switching between internal clock and ACP ACLK.
Signed-off-by: Vijendar Mukunda <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
ACP clock mux selection register is already programmed during acp init
sequence.
Remove the redundant register write.
Signed-off-by: Vijendar Mukunda <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Add module parameter for firmware debug. If firmware debug
flag is enabled, clear the fusion stall bit which is required
for enabling firmware debugging through JTAG.
Signed-off-by: Vijendar Mukunda <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Previously ACP SOF firmware used to enable the ACP external
global interrupt register.
This will restrict to report ACP host interrupts only after
firmware loading is successful.
This register needs to be set from host driver to handle
other ACP interrupts(SoundWire Interrupts) before loading
the ACP firmware.
Add field for external interrupt enable register in acp descriptor
structure and enable the external interrupt enable register.
Signed-off-by: Vijendar Mukunda <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
During initial development time for RN platform, when SHA
dma gets completed, SHA DMA engine used to raise the ACP interrupt.
In ACP interrupt handler, SHA DMA interrupt got handled.
Currently SHA DMA compleition is verified by checking
transfer count using read poll time out logic.
Remove unused SHA dma interrupt handling code.
Signed-off-by: Vijendar Mukunda <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
The current analog gain TLV seems to have completely incorrect values in
it. The gain starts at 0.5dB, proceeds in 1dB steps, and has no mute
value, correct the control to match.
Signed-off-by: Charles Keepax <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
ALSA SoC merges DAI call backs into .ops.
This patch merge these into one.
Reported-by: kernel test robot <[email protected]>
Closes: https://lore.kernel.org/oe-kbuild-all/[email protected]/
Cc: Randy Dunlap <[email protected]>
Fixes: 446b31e89493 ("ASoC: soc-dai.h: remove unused call back functions")
Signed-off-by: Kuninori Morimoto <[email protected]>
Reported-by: Randy Dunlap <[email protected]>
Acked-by: Randy Dunlap <[email protected]>
Tested-by: Randy Dunlap <[email protected]> # build-tested
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Add a new module parameter ipc4_ignore_cpc which can be used to force the
kernel to ignore the queried CPC value for all firmware modules and use 0
instead.
The CPC lookup is still done to report missing configurations and the
debug print is going to be different to be explicit that the CPC is ignored
and what was the value we would have used.
The CPC value is sent to the firmware with the MOD_INIT_INSTANCE message
and it is used by the firmware as a parameter for clock scaling.
The flag is intended to be used only when there is a need to validate the
firmware behavior regarding to clock scaling since the 0 CPC value will
force the DSP to run in full speed, disabling the scaling and provides
additional counter point to rule out clock management related issues.
Signed-off-by: Peter Ujfalusi <[email protected]>
Reviewed-by: Pierre-Louis Bossart <[email protected]>
Reviewed-by: Ranjani Sridharan <[email protected]>
Reviewed-by: Kai Vehmanen <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
ALSA SoC merges DAI call backs into .ops.
This patch merge these into one.
Reported-by: kernel test robot <[email protected]>
Closes: https://lore.kernel.org/oe-kbuild-all/[email protected]/
Fixes: 446b31e89493 ("ASoC: soc-dai.h: remove unused call back functions")
Signed-off-by: Kuninori Morimoto <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Merge series from Peter Ujfalusi <[email protected]>:
The SRC component in a pipeline provides flexibility on the sampling
rate which was not handled previously. This series will improve the
kernel side with the needed logic to be able to deal with the SRC type
of components in pipelines.
|
|
Merge series from Charles Keepax <[email protected]>:
This patch chain adds support for the Cirrus Logic cs42l43 PC focused
SoundWire CODEC. The chain is currently based of Lee's for-mfd-next
branch.
This series is mostly just a resend keeping pace with the kernel under
it, except for a minor fixup in the ASoC stuff.
Thanks,
Charles
Charles Keepax (4):
dt-bindings: mfd: cirrus,cs42l43: Add initial DT binding
mfd: cs42l43: Add support for cs42l43 core driver
pinctrl: cs42l43: Add support for the cs42l43
ASoC: cs42l43: Add support for the cs42l43
Lucas Tanure (2):
soundwire: bus: Allow SoundWire peripherals to register IRQ handlers
spi: cs42l43: Add SPI controller support
.../bindings/sound/cirrus,cs42l43.yaml | 313 +++
MAINTAINERS | 4 +
drivers/mfd/Kconfig | 23 +
drivers/mfd/Makefile | 3 +
drivers/mfd/cs42l43-i2c.c | 98 +
drivers/mfd/cs42l43-sdw.c | 239 ++
drivers/mfd/cs42l43.c | 1188 +++++++++
drivers/mfd/cs42l43.h | 28 +
drivers/pinctrl/cirrus/Kconfig | 11 +
drivers/pinctrl/cirrus/Makefile | 2 +
drivers/pinctrl/cirrus/pinctrl-cs42l43.c | 609 +++++
drivers/soundwire/bus.c | 32 +
drivers/soundwire/bus_type.c | 12 +
drivers/spi/Kconfig | 7 +
drivers/spi/Makefile | 1 +
drivers/spi/spi-cs42l43.c | 284 ++
include/linux/mfd/cs42l43-regs.h | 1184 +++++++++
include/linux/mfd/cs42l43.h | 102 +
include/linux/soundwire/sdw.h | 9 +
include/sound/cs42l43.h | 17 +
sound/soc/codecs/Kconfig | 16 +
sound/soc/codecs/Makefile | 4 +
sound/soc/codecs/cs42l43-jack.c | 946 +++++++
sound/soc/codecs/cs42l43-sdw.c | 74 +
sound/soc/codecs/cs42l43.c | 2278 +++++++++++++++++
sound/soc/codecs/cs42l43.h | 131 +
26 files changed, 7615 insertions(+)
create mode 100644 Documentation/devicetree/bindings/sound/cirrus,cs42l43.yaml
create mode 100644 drivers/mfd/cs42l43-i2c.c
create mode 100644 drivers/mfd/cs42l43-sdw.c
create mode 100644 drivers/mfd/cs42l43.c
create mode 100644 drivers/mfd/cs42l43.h
create mode 100644 drivers/pinctrl/cirrus/pinctrl-cs42l43.c
create mode 100644 drivers/spi/spi-cs42l43.c
create mode 100644 include/linux/mfd/cs42l43-regs.h
create mode 100644 include/linux/mfd/cs42l43.h
create mode 100644 include/sound/cs42l43.h
create mode 100644 sound/soc/codecs/cs42l43-jack.c
create mode 100644 sound/soc/codecs/cs42l43-sdw.c
create mode 100644 sound/soc/codecs/cs42l43.c
create mode 100644 sound/soc/codecs/cs42l43.h
--
2.30.2
|
|
I noticed typos and i fixed them.
Signed-off-by: Senhong Liu <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Enable signed firmware loading for Vangogh platform using dmi quirks.
Signed-off-by: Venkata Prasad Potturu <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Add support for signed firmware code bin and data bin
loading for amd platforms.
Signed-off-by: Venkata Prasad Potturu <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Add pci driver and platform driver to enable SOF support
on ACP5x architecture based Vangogh platform.
Signed-off-by: Venkata Prasad Potturu <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
The error path of tas2781_hda_bind() needs to release PM refcount as
well. Modify the code flow to handle properly.
Fixes: 5be27f1e3ec9 ("ALSA: hda/tas2781: Add tas2781 HDA driver")
Reported-by: Pierre-Louis Bossart <[email protected]>
Closes: https://lore.kernel.org/r/[email protected]
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
The error path at tas2781_read_acpi() doesn't release the acpi_device
adev but releases another device physdev instead. This results in a
refcount leak. Fix it by replacing with the right object.
Fixes: 5be27f1e3ec9 ("ALSA: hda/tas2781: Add tas2781 HDA driver")
Reported-by: Pierre-Louis Bossart <[email protected]>
Closes: https://lore.kernel.org/r/[email protected]
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
There have been reports of USB-audio driver spewing errors at the
probe time on a few devices like Jabra and Logitech. The suggested
fix there couldn't be applied as is, unfortunately, because it'll
likely break other devices.
But, the patch suggested an interesting point: looking at the current
init code in stream.c, one may notice that it does initialize
differently from the device setup in endpoint.c. Namely, for UAC1, we
should call snd_usb_init_pitch() and snd_usb_init_sample_rate() after
setting the interface, while the init sequence at parsing calls them
before setting the interface blindly.
This patch changes the init sequence at parsing for UAC1 (and other
devices that need a similar behavior) to be aligned with the rest of
the code, setting the interface at first. And, this fixes the
long-standing problems on a few UAC1 devices like Jabra / Logitech,
as reported, too.
Reported-and-tested-by: Joakim Tjernlund <[email protected]>
Closes: https://lore.kernel.org/r/[email protected]
Cc: <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
If the copier has only output valid_bits across all its output
formats, the reference for selecting the output format must be set that
instead of the valid_bits from the selected input format.
Signed-off-by: Ranjani Sridharan <[email protected]>
Reviewed-by: Bard Liao <[email protected]>
Reviewed-by: Seppo Ingalsuo <[email protected]>
Reviewed-by: Pierre-Louis Bossart <[email protected]>
Signed-off-by: Peter Ujfalusi <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
When we walk the list of connected widgets from the source to the sink
to prepare all widgets, the pipeline_params must be modified to reflect
the output audio format at each widget. But, the copier only modifies
the sample format in the pipeline_params. So, fix it to also modify the
rate and channels.
Signed-off-by: Ranjani Sridharan <[email protected]>
Reviewed-by: Bard Liao <[email protected]>
Reviewed-by: Pierre-Louis Bossart <[email protected]>
Reviewed-by: Seppo Ingalsuo <[email protected]>
Signed-off-by: Peter Ujfalusi <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
For playback, the SRC sink rate must be configured based on the requested
output format which is restricted to only handle DAI's that support a
single audio format for now. For capture, the SRC module should convert
the rate to match the rate requested by the PCM hw_params.
Signed-off-by: Ranjani Sridharan <[email protected]>
Reviewed-by: Bard Liao <[email protected]>
Reviewed-by: Pierre-Louis Bossart <[email protected]>
Reviewed-by: Seppo Ingalsuo <[email protected]>
Signed-off-by: Peter Ujfalusi <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Modify the pipeline_params based on the SRC output format and set the
sink_rate in the IPC data.
Signed-off-by: Ranjani Sridharan <[email protected]>
Reviewed-by: Bard Liao <[email protected]>
Reviewed-by: Pierre-Louis Bossart <[email protected]>
Reviewed-by: Seppo Ingalsuo <[email protected]>
Signed-off-by: Peter Ujfalusi <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
There is a spelling mistake in a quirk entry. Fix it.
Signed-off-by: Colin Ian King <[email protected]>
Fixes: 3babae915f4c ("ALSA: hda/tas2781: Add tas2781 HDA driver")
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
The CS42L43 is an audio CODEC with integrated MIPI SoundWire interface
(Version 1.2.1 compliant), I2C, SPI, and I2S/TDM interfaces designed
for portable applications. It provides a high dynamic range, stereo
DAC for headphone output, two integrated Class D amplifiers for
loudspeakers, and two ADCs for wired headset microphone input or
stereo line input. PDM inputs are provided for digital microphones.
The ASoC component provides the majority of the functionality of the
device, all the audio functions.
Signed-off-by: Charles Keepax <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
VivoBook Pro 15 Ryzen Edition uses Ryzen 6800H processor, and adding to
quirks list for acp6x will enable internal mic.
Signed-off-by: BrenoRCBrito <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
merge window
Merge tag 'ib-mfd-pinctrl-soundwire-v6.6' of https://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd into tmp
Immutable branch between MFD, Pinctrl and soundwire due for the v6.6 merge window
|
|
These are not implemented, so can remove them.
Signed-off-by: Yue Haibing <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
Commit 7ac3404c2e21 ("ASoC: amd: acp: Map missing jack kcontrols") adds
card kcontrols and DAPM widgets corresponding to jacks for Headphone and
Headset Mic. But these were already being added in acp-legacy-mach.c and
acp-sof-mach.c, so this causes a probe error:
sof_mach rt5682s-hs-rt1019: control 2:0:0:Headphone Jack Switch:0 is already present
sof_mach rt5682s-hs-rt1019: ASoC: Failed to add Headphone Jack Switch: -16
sof_mach rt5682s-hs-rt1019: devm_snd_soc_register_card(sof-rt5682s-hs-rt1019) failed: -16
sof_mach: probe of rt5682s-hs-rt1019 failed with error -16
Removing the new duplicates from the common code might be enough to fix
the issue. But some of the codecs use different kcontrols and widgets.
NAU8821 alone has an "Int Mic". MAX98360A has a single "Spk", while
RT1019 has "Left Spk" and "Right Spk" (and two codec instances with name
prefixes).
Since there are per-codec differences, add the kcontrols and widgets
in the common code as each dai-link is being initialized, instead of in
the two machine drivers' probe().
Also, MAX98388 has Left and Right instances, but uses a single "SPK"
widget. That seems weird, so normalize it to use two widgets (one per
each instance like RT1019) while we're adding controls.
Fixes: 7ac3404c2e21 ("ASoC: amd: acp: Map missing jack kcontrols")
Signed-off-by: Alper Nebi Yasak <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
This patch will improve the depop function of CBJ detection before the headphone playback
when the system resumes.
We also want to complete the CBJ detection in the system-level resume function.
It could avoid triggering the detection at the playing state of headphones.
Signed-off-by: Shuming Fan <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Finally all users have been converted to the new PCM copy ops, let's
drop the obsoleted copy_kernel and copy_user ops completely.
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
Now all ASoC users have been replaced to use the new PCM copy ops,
let's drop the obsoleted copy_user ops and its helper function.
Reviewed-by: Mark Brown <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
Update the documentation about the PCM copy callbacks.
The update was kept minimalistic, just correcting the use of copy_user
ops with the single copy ops, and drop/update the text mentioning the
copy_kernel.
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
Along with the conversion to PCM copy ops, use the iov_iter for the
pointer to be passed to the dmaengine process callback, too. It
avoids the direct reference of iter_iov_addr(), and it can potentially
help for the drivers to access memory properly (although both atmel
and stm drivers don't use the given buffer address at all for now).
Reviewed-by: Mark Brown <[email protected]>
Cc: Lars-Peter Clausen <[email protected]>
Cc: Claudiu Beznea <[email protected]>
Cc: Olivier Moysan <[email protected]>
Cc: Arnaud Pouliquen <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
This patch converts the ASoC dmaenging driver code to use the new
unified PCM copy callback. It's a straightforward conversion from
*_user() to *_iter() variants.
The process callback is still using the direct pointer as of now, but
it'll be converted in the next patch.
Note that copy_from/to_iter() returns the copied bytes, hence the
error condition is adjusted accordingly.
Reviewed-by: Mark Brown <[email protected]>
Cc: Lars-Peter Clausen <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
This patch converts the qcom lpass driver code to use the new unified
PCM copy callback. It's a straightforward conversion from *_user() to
*_iter() variants.
Note that copy_from/to_iter() returns the copied bytes, hence the
error condition is adjusted accordingly.
Reviewed-by: Mark Brown <[email protected]>
Cc: Srinivas Kandagatla <[email protected]>
Cc: Banajit Goswami <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
This patch converts the mediatek BT SCO driver code to use the new
unified PCM copy callback. It's a straightforward conversion from
*_user() to *_iter() variants. As copy_form/to_iter() updates the
internal offset at each read/write, we can drop the cur_*_idx counter
in the loop, too.
Note that copy_from/to_iter() returns the copied bytes, hence the
error condition is adjusted accordingly.
Reviewed-by: Mark Brown <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
For following the ALSA PCM core change, a new PCM copy ops is added
toe ASoC component framework: snd_soc_component_driver receives the
copy ops, and snd_soc_pcm_component_copy() helper is provided.
This also fixes a long-standing potential bug where the ASoC driver
covers only copy_user PCM callback and misses the copy from kernel
pointers (such as OSS PCM layer), too.
As of this patch, the old copy_user is still kept, but it'll be
dropped later after all drivers are converted.
Reviewed-by: Mark Brown <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
This patch converts the solo6x10 driver code to use the new unified
PCM copy callback. It's a straightforward conversion from *_user() to
*_iter() variants. As copy_to_iter() updates the internal offest at
each write, we can drop the dst counter update in the loop, too.
Note that copy_to_iter() returns the copied bytes, hence the error
condition is adjusted accordingly.
Acked-by: Ismael Luceno <[email protected]>
Acked-by: Hans Verkuil <[email protected]>
Cc: Bluecherry Maintainers <[email protected]>
Cc: Anton Sviridenko <[email protected]>
Cc: Andrey Utkin <[email protected]>
Cc: Mauro Carvalho Chehab <[email protected]>
Cc: [email protected]
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
Just an update of a comment mentioning the old PCM callbacks to
correct to the new PCM copy ops.
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
This patch converts the xen frontend driver code to use the new
unified PCM copy callback. It's a straightforward conversion from
*_user() to *_iter() variants.
Note that copy_from/to_iter() returns the copied bytes, hence the
error condition is adjusted accordingly.
Cc: Oleksandr Andrushchenko <[email protected]>
Cc: [email protected]
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
This patch converts the sh_dac_audio driver code to use the new
unified PCM copy callback. It's a straightforward conversion from
*_user() to *_iter() variants.
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
This patch converts the rme9652 driver code to use the new unified PCM
copy callback. It's a straightforward conversion from *_user() to
*_iter() variants.
Note that copy_from/to_iter() returns the copied bytes, hence the
error condition is adjusted accordingly.
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
This patch converts the hdsp driver code to use the new unified PCM
copy callback. It's a straightforward conversion from *_user() to
*_iter() variants.
Note that copy_from/to_iter() returns the copied bytes, hence the
error condition is adjusted accordingly.
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|