| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
32 bits BOOKE have special interrupts for debug and other
critical events.
When handling those interrupts, dedicated registers are saved
in the stack frame in addition to the standard registers, leading
to a shift of the pt_regs struct.
Since commit db297c3b07af ("powerpc/32: Don't save thread.regs on
interrupt entry"), the pt_regs struct is expected to be at the
same place all the time.
Instead of handling a special struct in addition to pt_regs, just
add those special registers to struct pt_regs.
Fixes: db297c3b07af ("powerpc/32: Don't save thread.regs on interrupt entry")
Cc: [email protected]
Reported-by: Radu Rendec <[email protected]>
Signed-off-by: Christophe Leroy <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/028d5483b4851b01ea4334d0751e7f260419092b.1625637264.git.christophe.leroy@csgroup.eu
|
|
When a DSI (Data Storage Interrupt) is taken while in NAP mode,
r11 doesn't survive the call to power_save_ppc32_restore().
So use r1 instead of r11 as they both contain the virtual stack
pointer at that point.
Fixes: 4c0104a83fc3 ("powerpc/32: Dismantle EXC_XFER_STD/LITE/TEMPLATE")
Cc: [email protected] # v5.13+
Reported-by: Finn Thain <[email protected]>
Signed-off-by: Christophe Leroy <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/731694e0885271f6ee9ffc179eb4bcee78313682.1628003562.git.christophe.leroy@csgroup.eu
|
|
The kyber ioscheduler calls trace_block_rq_insert() *after* the request
is added to the queue but the documentation for trace_block_rq_insert()
says that the call should be made *before* the request is added to the
queue. Move the tracepoint for the kyber ioscheduler so that it is
consistent with the documentation.
Signed-off-by: Vincent Fu <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed by: Adam Manzanares <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
[Why]
With kernel module parameter "freesync_video" is enabled, if the mode
is changed to preferred mode(the mode with highest rate), then Freesync
fails because the preferred mode is treated as one of freesync video
mode, and then be configurated as freesync video mode(fixed refresh
rate).
[How]
Skip freesync fixed rate configurating when modeset to preferred mode.
Signed-off-by: Solomon Chiu <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
Cc: [email protected]
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"A regression fix, bug fix, and a comment cleanup for ext4"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix potential htree corruption when growing large_dir directories
ext4: remove conflicting comment from __ext4_forget
ext4: fix potential uninitialized access to retval in kmmpd
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Fix tracepoint race between static_call and callback data
As callbacks to a tracepoint are paired with the data that is passed
in when the callback is registered to the tracepoint, it must have
that data passed to the callback when the tracepoint is triggered,
else bad things will happen. To keep the two together, they are both
assigned to a tracepoint structure and added to an array. The
tracepoint call site will dereference the structure (via RCU) and call
the callback in that structure along with the data in that structure.
This keeps the callback and data tightly coupled.
Because of the overhead that retpolines have on tracepoint callbacks,
if there's only one callback attached to a tracepoint (a common case),
then it is called via a static call (code modified to do a direct call
instead of an indirect call). But to implement this, the data had to
be decoupled from the callback, as now the callback is implemented via
a direct call from the static call and not an indirect call from the
dereferenced structure.
Note, the static call only calls a callback used when there's a single
callback attached to the tracepoint. If more than one callback is
attached to the same tracepoint, then the static call will call an
iterator function that goes back to dereferencing the structure
keeping the callback and its data tightly coupled again.
Issues can arise when going from 0 callbacks to one, as the static
call is assigned to the callback, and it must take care that the data
passed to it is loaded before the static call calls the callback.
Going from 1 to 2 callbacks is not an issue, as long as the static
call is updated to the iterator before the tracepoint structure array
is updated via RCU. Going from 2 to more or back down to 2 is not an
issue as the iterator can handle all theses cases. But going from 2 to
1, care must be taken as the static call is now calling a callback and
the data that is loaded must be the data for that callback.
Care was taken to ensure the callback and data would be in-sync, but
after a bug was reported, it became clear that not enough was done to
make sure that was the case. These changes address this.
The first change is to compare the old and new data instead of the old
and new callback, as it's the data that can corrupt the callback, even
if the callback is the same (something getting freed).
The next change is to convert these transitions into states, to make
it easier to know when a synchronization is needed, and to perform
those synchronizations. The problem with this patch is that it slows
down disabling all events from under a second, to making it take over
10 seconds to do the same work. But that is addressed in the final
patch.
The final patch uses the RCU state functions to keep track of the RCU
state between the transitions, and only needs to perform the
synchronization if an RCU synchronization hasn't been done already.
This brings the performance of disabling all events back to its
original value. That's because no synchronization is required between
disabling tracepoints but is required when enabling a tracepoint after
its been disabled. If an RCU synchronization happens after the
tracepoint is disabled, and before it is re-enabled, there's no need
to do the synchronization again.
Both the second and third patch have subtle complexities that they are
separated into two patches. But because the second patch causes such a
regression in performance, the third patch adds a "Fixes" tag to the
second patch, such that the two must be backported together and not
just the second patch"
* tag 'trace-v5.14-rc4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracepoint: Use rcu get state and cond sync for static call updates
tracepoint: Fix static call function vs data state mismatch
tracepoint: static call: Compare data on transition from 2->1 callees
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"Fix a recent regression in the timer events oriented (TEO) cpuidle
governor causing it to misbehave when idle state 0 is disabled and
rename two local variables for improved clarity on top of that"
* tag 'pm-5.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpuidle: teo: Rename two local variables in teo_select()
cpuidle: teo: Fix alternative idle state lookup
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"Revert a recent ACPICA commit causing boot issues to appear on some
systems"
* tag 'acpi-5.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "ACPICA: Fix memory leak caused by _CID repair function"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"Lots of small fixes for Arm SoCs this time, nothing too worrying:
- omap/beaglebone boot regression fix in gpt12 timer
- revert for i.mx8 soc driver breaking as a platform_driver
- kexec/kdump fixes for op-tee
- various fixes for incorrect DT settings on imx, mvebu, omap, stm32,
and tegra causing problems.
- device tree fixes for static checks in nomadik, versatile, stm32
- code fixes for issues found in build testing and with static
checking on tegra, ixp4xx, imx, omap"
* tag 'soc-fixes-5.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (36 commits)
soc: ixp4xx/qmgr: fix invalid __iomem access
soc: ixp4xx: fix printing resources
ARM: ixp4xx: goramo_mlr depends on old PCI driver
ARM: ixp4xx: fix compile-testing soc drivers
soc/tegra: Make regulator couplers depend on CONFIG_REGULATOR
ARM: dts: nomadik: Fix up interrupt controller node names
ARM: dts: stm32: Fix touchscreen IRQ line assignment on DHCOM
ARM: dts: stm32: Disable LAN8710 EDPD on DHCOM
ARM: dts: stm32: Prefer HW RTC on DHCOM SoM
omap5-board-common: remove not physically existing vdds_1v8_main fixed-regulator
ARM: dts: am437x-l4: fix typo in can@0 node
ARM: dts: am43x-epos-evm: Reduce i2c0 bus speed for tps65218
bus: ti-sysc: AM3: RNG is GP only
ARM: omap2+: hwmod: fix potential NULL pointer access
arm64: dts: armada-3720-turris-mox: remove mrvl,i2c-fast-mode
arm64: dts: armada-3720-turris-mox: fixed indices for the SDHC controllers
ARM: dts: imx: Swap M53Menlo pinctrl_power_button/pinctrl_power_out pins
ARM: imx: fix missing 3rd argument in macro imx_mmdc_perf_init
ARM: dts: colibri-imx6ull: limit SDIO clock to 25MHz
arm64: dts: ls1028: sl28: fix networking for variant 2
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"It's all pretty minor but the main fix is sorting out how we deal with
return values from 32-bit system calls as audit expects error codes to
be sign-extended to 64 bits
Summary:
- Fix extension/truncation of return values from 32-bit system calls
- Fix interaction between unwinding and tracing
- Fix spurious toolchain warning emitted during make
- Fix Kconfig help text for RANDOMIZE_MODULE_REGION_FULL"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: stacktrace: avoid tracing arch_stack_walk()
arm64: stacktrace: fix comment
arm64: fix the doc of RANDOMIZE_MODULE_REGION_FULL
arm64: move warning about toolchains to archprepare
arm64: fix compat syscall return truncation
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fix from Thomas Bogendoerfer:
"Fix PMD accounting change"
* tag 'mips-fixes_5.14_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: check return value of pgtable_pmd_page_ctor
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A small collection of fixes for SPI, small mostly driver specific
things plus a fix for module autoloading which hadn't been working
properly for DT systems"
* tag 'spi-fix-v5.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: cadence-quadspi: Fix check condition for DTR ops
spi: mediatek: Fix fifo transfer
spi: imx: mx51-ecspi: Fix CONFIGREG delay comment
spi: imx: mx51-ecspi: Fix low-speed CONFIGREG delay calculation
spi: update modalias_show after of_device_uevent_modalias support
spi: meson-spicc: fix memory leak in meson_spicc_remove
spi: spi-mux: Add module info needed for autoloading
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine
Pull dmaengine fixes from Vinod Koul:
"A bunch of driver fixes, notably:
- idxd driver fixes for submission race, driver remove sequence,
setup sequence for MSIXPERM, array index and updating descriptor
vector
- usb-dmac, pm reference leak fix
- xilinx_dma, read-after-free fix
- uniphier-xdmac fix for using atomic readl_poll_timeout_atomic()
- of-dma, router_xlate to return
- imx-dma, generic dma fix"
* tag 'dmaengine-fix-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine:
dmaengine: imx-dma: configure the generic DMA type to make it work
dmaengine: of-dma: router_xlate to return -EPROBE_DEFER if controller is not yet available
dmaengine: stm32-dmamux: Fix PM usage counter unbalance in stm32 dmamux ops
dmaengine: stm32-dma: Fix PM usage counter imbalance in stm32 dma ops
dmaengine: uniphier-xdmac: Use readl_poll_timeout_atomic() in atomic state
dmaengine: idxd: fix submission race window
dmaengine: idxd: fix sequence for pci driver remove() and shutdown()
dmaengine: idxd: fix desc->vector that isn't being updated
dmaengine: idxd: fix setup sequence for MSIXPERM table
dmaengine: idxd: fix array index when int_handles are being used
dmaengine: usb-dmac: Fix PM reference leak in usb_dmac_probe()
dmaengine: xilinx_dma: Fix read-after-free bug when terminating transfers
|
|
Pull rdma fixes from Jason Gunthorpe:
"Several small recent regressions - rather more than usual, but nothing
too scary. Good to know people are testing.
- Typo causing incorrect operation of the mlx5 mkey cache
expiration
- Revert a CM patch that is breaking some ULPs
- Typo breaking SRQ in rxe
- Revert a rxe patch breaking icrc calculation
- Static checker warning about unbalanced locking in hns
- Subtle cxgb4 regression from a recent atomic to refcount
conversion"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/iw_cxgb4: Fix refcount underflow while destroying cqs.
RDMA/hns: Fix the double unlock problem of poll_sem
RDMA/rxe: Restore setting tot_len in the IPv4 header
RDMA/rxe: Use the correct size of wqe when processing SRQ
RDMA/cma: Revert INIT-INIT patch
RDMA/mlx5: Delay emptying a cache entry when a new MR is added to it recently
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of small fixes:
- A few regression fixes (PCM core fixes, USB-audio fixes)
- Follow up fixes for the USB-audio mixer changes in this cycle
- A long-standing ALSA sequencer race bug fix
- Usual device-specific quirks for HD- and USB-audio"
* tag 'sound-5.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: seq: Fix racy deletion of subscriber
ALSA: memalloc: Fix regression with SNDRV_DMA_TYPE_CONTINUOUS
ALSA: pcm - fix mmap capability check for the snd-dummy driver
ALSA: usb-audio: Avoid unnecessary or invalid connector selection at resume
ALSA: hda/realtek: add mic quirk for Acer SF314-42
ALSA: usb-audio: Add registration quirk for JBL Quantum 600
ALSA: hda/realtek: Fix headset mic for Acer SWIFT SF314-56 (ALC256)
ALSA: usb-audio: Fix superfluous autosuspend recovery
ALSA: usb-audio: fix incorrect clock source setting
ALSA: scarlett2: Fix line out/speaker switching notifications
ALSA: scarlett2: Correct channel mute status after mute button pressed
ALSA: scarlett2: Fix Direct Monitor control name for 2i2
ALSA: scarlett2: Fix Mute/Dim/MSD Mode control names
|
|
Pull drm fixes from Dave Airlie:
"Regular weekly fixes pull, live from a Brisbane lockdown with kids at
home.
A big bunch of scattered amdgpu fixes, but they are all pretty small,
minor i915 fixes, kmb, and one vmwgfx regression fixes, all pretty
quiet for this time.
amdgpu:
- Fix potential out-of-bounds read when updating GPUVM mapping
- Renoir powergating fix
- Yellow Carp updates
- 8K fix for navi1x
- Beige Goby updates and new DIDs
- Fix DMUB firmware version output
- EDP fix
- pmops config fix
i915:
- Call i915_globals_exit if pci_register_device fails
- (follow on fix for section mismatch)
- Correct SFC_DONE register offset
kmb:
- DMA fix
- driver date/version macros
vmwgfx:
- Fix I/O memory access on 64-bit systems"
* tag 'drm-fixes-2021-08-06' of git://anongit.freedesktop.org/drm/drm:
drm/amdgpu: add DID for beige goby
drm/amdgpu/display: fix DMUB firmware version info
drm/amd/display: workaround for hard hang on HPD on native DP
drm/amd/display: Fix resetting DCN3.1 HW when resuming from S4
drm/amd/display: Increase stutter watermark for dcn303
drm/amd/display: Fix Dynamic bpp issue with 8K30 with Navi 1X
drm/amd/display: Assume LTTPR interop for DCN31+
drm/amdgpu: fix checking pmops when PM_SLEEP is not enabled
drm/amd/pm: update yellow carp pmfw interface version
drm/i915: fix i915_globals_exit() section mismatch error
drm/i915: Call i915_globals_exit() if pci_register_device() fails
drm/i915: Correct SFC_DONE register offset
drm/vmwgfx: Fix a 64bit regression on svga3
drm/amdgpu: fix the doorbell missing when in CGPG issue for renoir.
drm/amdgpu: Fix out-of-bounds read when update mapping
drm/kmb: Define driver date and major/minor version
drm/kmb: Enable LCD DMA for low TVDDCV
|
|
Commit b5776e7524af ("ext4: fix potential htree index checksum
corruption) removed a required restart when multiple levels of index
nodes need to be split. Fix this to avoid directory htree corruptions
when using the large_dir feature.
Cc: [email protected] # v5.11
Cc: Благодаренко Артём <[email protected]>
Fixes: b5776e7524af ("ext4: fix potential htree index checksum corruption)
Reported-by: Denis <[email protected]>
Signed-off-by: Theodore Ts'o <[email protected]>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Restrict range element expansion in ipset to avoid soft lockup,
from Jozsef Kadlecsik.
2) Memleak in error path for nf_conntrack_bridge for IPv4 packets,
from Yajun Deng.
3) Simplify conntrack garbage collection strategy to avoid frequent
wake-ups, from Florian Westphal.
4) Fix NFNLA_HOOK_FUNCTION_NAME string, do not include module name.
5) Missing chain family netlink attribute in chain description
in nfnetlink_hook.
6) Incorrect sequence number on nfnetlink_hook dumps.
7) Use netlink request family in reply message for consistency.
8) Remove offload_pickup sysctl, use conntrack for established state
instead, from Florian Westphal.
9) Translate NFPROTO_INET/ingress to NFPROTO_NETDEV/ingress, since
NFPROTO_INET is not exposed through nfnetlink_hook.
* git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf:
netfilter: nfnetlink_hook: translate inet ingress to netdev
netfilter: conntrack: remove offload_pickup sysctl again
netfilter: nfnetlink_hook: Use same family as request message
netfilter: nfnetlink_hook: use the sequence number of the request message
netfilter: nfnetlink_hook: missing chain family
netfilter: nfnetlink_hook: strip off module name from hookfn
netfilter: conntrack: collect all entries in one cycle
netfilter: nf_conntrack_bridge: Fix memory leak when error
netfilter: ipset: Limit the maximal range of consecutive elements to add/delete
====================
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
'vangogh_tables_init()'
'watermarks_table' must be freed instead 'clocks_table', because
'clocks_table' is known to be NULL at this point and 'watermarks_table' is
never freed if the last kzalloc fails.
Fixes: c98ee89736b8 ("drm/amd/pm: add the fine grain tuning function for vangogh")
Signed-off-by: Christophe JAILLET <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
If the platform uses BOCO, don't use BACO in runtime suspend.
We could end up executing the BACO path if the platform supports
both.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1669
Reviewed-by: Evan Quan <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
Cc: [email protected]
|
|
update to latest atombios fw table
[Backport to 5.14 - Alex]
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1670
Signed-off-by: John Clements <[email protected]>
Reviewed-by: Hawking Zhang <[email protected]>.
Signed-off-by: Alex Deucher <[email protected]>
Cc: [email protected]
|
|
Update smu v13.0.1 firmware header for yellow carp.
Signed-off-by: Xiaomeng Hou <[email protected]>
Reviewed-by: Aaron Liu <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
The NFPROTO_INET pseudofamily is not exposed through this new netlink
interface. The netlink dump either shows NFPROTO_IPV4 or NFPROTO_IPV6
for NFPROTO_INET prerouting/input/forward/output/postrouting hooks.
The NFNLA_CHAIN_FAMILY attribute provides the family chain, which
specifies if this hook applies to inet traffic only (either IPv4 or
IPv6).
Translate the inet/ingress hook to netdev/ingress to fully hide the
NFPROTO_INET implementation details.
Fixes: e2cf17d3774c ("netfilter: add new hook nfnl subsystem")
Signed-off-by: Pablo Neira Ayuso <[email protected]>
|
|
These two sysctls were added because the hardcoded defaults (2 minutes,
tcp, 30 seconds, udp) turned out to be too low for some setups.
They appeared in 5.14-rc1 so it should be fine to remove it again.
Marcelo convinced me that there should be no difference between a flow
that was offloaded vs. a flow that was not wrt. timeout handling.
Thus the default is changed to those for TCP established and UDP stream,
5 days and 120 seconds, respectively.
Marcelo also suggested to account for the timeout value used for the
offloading, this avoids increase beyond the value in the conntrack-sysctl
and will also instantly expire the conntrack entry with altered sysctls.
Example:
nf_conntrack_udp_timeout_stream=60
nf_flowtable_udp_timeout=60
This will remove offloaded udp flows after one minute, rather than two.
An earlier version of this patch also cleared the ASSURED bit to
allow nf_conntrack to evict the entry via early_drop (i.e., table full).
However, it looks like we can safely assume that connection timed out
via HW is still in established state, so this isn't needed.
Quoting Oz:
[..] the hardware sends all packets with a set FIN flags to sw.
[..] Connections that are aged in hardware are expected to be in the
established state.
In case it turns out that back-to-sw-path transition can occur for
'dodgy' connections too (e.g., one side disappeared while software-path
would have been in RETRANS timeout), we can adjust this later.
Cc: Oz Shlomo <[email protected]>
Cc: Paul Blakey <[email protected]>
Suggested-by: Marcelo Ricardo Leitner <[email protected]>
Signed-off-by: Florian Westphal <[email protected]>
Reviewed-by: Marcelo Ricardo Leitner <[email protected]>
Reviewed-by: Oz Shlomo <[email protected]>
Signed-off-by: Pablo Neira Ayuso <[email protected]>
|
|
Use the same family as the request message, for consistency. The
netlink payload provides sufficient information to describe the hook
object, including the family.
This makes it easier to userspace to correlate the hooks are that
visited by the packets for a certain family.
Fixes: e2cf17d3774c ("netfilter: add new hook nfnl subsystem")
Signed-off-by: Pablo Neira Ayuso <[email protected]>
|
|
The sequence number allows to correlate the netlink reply message (as
part of the dump) with the original request message.
The cb->seq field is internally used to detect an interference (update)
of the hook list during the netlink dump, do not use it as sequence
number in the netlink dump header.
Fixes: e2cf17d3774c ("netfilter: add new hook nfnl subsystem")
Signed-off-by: Pablo Neira Ayuso <[email protected]>
|
|
The family is relevant for pseudo-families like NFPROTO_INET
otherwise the user needs to rely on the hook function name to
differentiate it from NFPROTO_IPV4 and NFPROTO_IPV6 names.
Add nfnl_hook_chain_desc_attributes instead of using the existing
NFTA_CHAIN_* attributes, since these do not provide a family number.
Fixes: e2cf17d3774c ("netfilter: add new hook nfnl subsystem")
Signed-off-by: Pablo Neira Ayuso <[email protected]>
|
|
NFNLA_HOOK_FUNCTION_NAME should include the hook function name only,
the module name is already provided by NFNLA_HOOK_MODULE_NAME.
Fixes: e2cf17d3774c ("netfilter: add new hook nfnl subsystem")
Signed-off-by: Pablo Neira Ayuso <[email protected]>
|
|
Michal Kubecek reports that conntrack gc is responsible for frequent
wakeups (every 125ms) on idle systems.
On busy systems, timed out entries are evicted during lookup.
The gc worker is only needed to remove entries after system becomes idle
after a busy period.
To resolve this, always scan the entire table.
If the scan is taking too long, reschedule so other work_structs can run
and resume from next bucket.
After a completed scan, wait for 2 minutes before the next cycle.
Heuristics for faster re-schedule are removed.
GC_SCAN_INTERVAL could be exposed as a sysctl in the future to allow
tuning this as-needed or even turn the gc worker off.
Reported-by: Michal Kubecek <[email protected]>
Signed-off-by: Florian Westphal <[email protected]>
Signed-off-by: Pablo Neira Ayuso <[email protected]>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v5.14
Quite a lot of fixes here, the biggest set being for the cs42l42 driver
which is reasonably old but has seen a sudden uptick in activity.
There's also some fixes for correctly referencing PCM buffer addresses
and the removal of some driver-local bodges that had been done for the
lack of prefix handling in DAPM which were broken by the core handling
that as expected.
|
|
State transitions from 1->0->1 and N->2->1 callbacks require RCU
synchronization. Rather than performing the RCU synchronization every
time the state change occurs, which is quite slow when many tracepoints
are registered in batch, instead keep a snapshot of the RCU state on the
most recent transitions which belong to a chain, and conditionally wait
for a grace period on the last transition of the chain if one g.p. has
not elapsed since the last snapshot.
This applies to both RCU and SRCU.
This brings the performance regression caused by commit 231264d6927f
("Fix: tracepoint: static call function vs data state mismatch") back to
what it was originally.
Before this commit:
# trace-cmd start -e all
# time trace-cmd start -p nop
real 0m10.593s
user 0m0.017s
sys 0m0.259s
After this commit:
# trace-cmd start -e all
# time trace-cmd start -p nop
real 0m0.878s
user 0m0.000s
sys 0m0.103s
Link: https://lkml.kernel.org/r/[email protected]
Link: https://lore.kernel.org/io-uring/[email protected]/
Cc: [email protected]
Cc: Ingo Molnar <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Andrew Morton <[email protected]>
Cc: "Paul E. McKenney" <[email protected]>
Cc: Stefan Metzmacher <[email protected]>
Fixes: 231264d6927f ("Fix: tracepoint: static call function vs data state mismatch")
Signed-off-by: Mathieu Desnoyers <[email protected]>
Reviewed-by: Paul E. McKenney <[email protected]>
Signed-off-by: Steven Rostedt (VMware) <[email protected]>
|
|
There should be this judgement before we create an io-worker
Fixes: 685fe7feedb9 ("io-wq: eliminate the need for a manager thread")
Signed-off-by: Hao Xu <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
There is an acct->nr_worker visit without lock protection. Think about
the case: two callers call io_wqe_wake_worker(), one is the original
context and the other one is an io-worker(by calling
io_wqe_enqueue(wqe, linked)), on two cpus paralelly, this may cause
nr_worker to be larger than max_worker.
Let's fix it by adding lock for it, and let's do nr_workers++ before
create_io_worker. There may be a edge cause that the first caller fails
to create an io-worker, but the second caller doesn't know it and then
quit creating io-worker as well:
say nr_worker = max_worker - 1
cpu 0 cpu 1
io_wqe_wake_worker() io_wqe_wake_worker()
nr_worker < max_worker
nr_worker++
create_io_worker() nr_worker == max_worker
failed return
return
But the chance of this case is very slim.
Fixes: 685fe7feedb9 ("io-wq: eliminate the need for a manager thread")
Signed-off-by: Hao Xu <[email protected]>
[axboe: fix unconditional create_io_worker() call]
Signed-off-by: Jens Axboe <[email protected]>
|
|
SCHED_FLAG_KEEP_PARAMS can be passed to sched_setattr to specify that
the call must not touch scheduling parameters (nice or priority). This
is particularly handy for uclamp when used in conjunction with
SCHED_FLAG_KEEP_POLICY as that allows to issue a syscall that only
impacts uclamp values.
However, sched_setattr always checks whether the priorities and nice
values passed in sched_attr are valid first, even if those never get
used down the line. This is useless at best since userspace can
trivially bypass this check to set the uclamp values by specifying low
priorities. However, it is cumbersome to do so as there is no single
expression of this that skips both RT and CFS checks at once. As such,
userspace needs to query the task policy first with e.g. sched_getattr
and then set sched_attr.sched_priority accordingly. This is racy and
slower than a single call.
As the priority and nice checks are useless when SCHED_FLAG_KEEP_PARAMS
is specified, simply inherit them in this case to match the policy
inheritance of SCHED_FLAG_KEEP_POLICY.
Reported-by: Wei Wang <[email protected]>
Signed-off-by: Quentin Perret <[email protected]>
Signed-off-by: Peter Zijlstra (Intel) <[email protected]>
Reviewed-by: Dietmar Eggemann <[email protected]>
Reviewed-by: Qais Yousef <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
The UCLAMP_FLAG_IDLE flag is set on a runqueue when dequeueing the last
uclamp active task (that is, when buckets.tasks reaches 0 for all
buckets) to maintain the last uclamp.max and prevent blocked util from
suddenly becoming visible.
However, there is an asymmetry in how the flag is set and cleared which
can lead to having the flag set whilst there are active tasks on the rq.
Specifically, the flag is cleared in the uclamp_rq_inc() path, which is
called at enqueue time, but set in uclamp_rq_dec_id() which is called
both when dequeueing a task _and_ in the update_uclamp_active() path. As
a result, when both uclamp_rq_{dec,ind}_id() are called from
update_uclamp_active(), the flag ends up being set but not cleared,
hence leaving the runqueue in a broken state.
Fix this by clearing the flag in update_uclamp_active() as well.
Fixes: e496187da710 ("sched/uclamp: Enforce last task's UCLAMP_MAX")
Reported-by: Rick Yiu <[email protected]>
Signed-off-by: Quentin Perret <[email protected]>
Signed-off-by: Peter Zijlstra (Intel) <[email protected]>
Reviewed-by: Qais Yousef <[email protected]>
Tested-by: Dietmar Eggemann <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
A missing clock update is causing the following warning:
rq->clock_update_flags < RQCF_ACT_SKIP
WARNING: CPU: 112 PID: 2041 at kernel/sched/sched.h:1453
sub_running_bw.isra.0+0x190/0x1a0
...
CPU: 112 PID: 2041 Comm: sugov:112 Tainted: G W 5.14.0-rc1 #1
Hardware name: WIWYNN Mt.Jade Server System
B81.030Z1.0007/Mt.Jade Motherboard, BIOS 1.6.20210526 (SCP:
1.06.20210526) 2021/05/26
...
Call trace:
sub_running_bw.isra.0+0x190/0x1a0
migrate_task_rq_dl+0xf8/0x1e0
set_task_cpu+0xa8/0x1f0
try_to_wake_up+0x150/0x3d4
wake_up_q+0x64/0xc0
__up_write+0xd0/0x1c0
up_write+0x4c/0x2b0
cppc_set_perf+0x120/0x2d0
cppc_cpufreq_set_target+0xe0/0x1a4 [cppc_cpufreq]
__cpufreq_driver_target+0x74/0x140
sugov_work+0x64/0x80
kthread_worker_fn+0xe0/0x230
kthread+0x138/0x140
ret_from_fork+0x10/0x18
The task causing this is the `cppc_fie` DL task introduced by
commit 1eb5dde674f5 ("cpufreq: CPPC: Add support for frequency
invariance").
With CONFIG_ACPI_CPPC_CPUFREQ_FIE=y and schedutil cpufreq governor on
slow-switching system (like on this Ampere Altra WIWYNN Mt. Jade Arm
Server):
DL task `curr=sugov:112` lets `p=cppc_fie` migrate and since the latter
is in `non_contending` state, migrate_task_rq_dl() calls
sub_running_bw()->__sub_running_bw()->cpufreq_update_util()->
rq_clock()->assert_clock_updated()
on p.
Fix this by updating the clock for a non_contending task in
migrate_task_rq_dl() before calling sub_running_bw().
Reported-by: Bruno Goncalves <[email protected]>
Signed-off-by: Dietmar Eggemann <[email protected]>
Signed-off-by: Peter Zijlstra (Intel) <[email protected]>
Reviewed-by: Daniel Bristot de Oliveira <[email protected]>
Acked-by: Juri Lelli <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
A warning as below may be occasionally triggered in an ADL machine when
these conditions occur:
- Two perf record commands run one by one. Both record a PEBS event.
- Both runs on small cores.
- They have different adaptive PEBS configuration (PEBS_DATA_CFG).
[ ] WARNING: CPU: 4 PID: 9874 at arch/x86/events/intel/ds.c:1743 setup_pebs_adaptive_sample_data+0x55e/0x5b0
[ ] RIP: 0010:setup_pebs_adaptive_sample_data+0x55e/0x5b0
[ ] Call Trace:
[ ] <NMI>
[ ] intel_pmu_drain_pebs_icl+0x48b/0x810
[ ] perf_event_nmi_handler+0x41/0x80
[ ] </NMI>
[ ] __perf_event_task_sched_in+0x2c2/0x3a0
Different from the big core, the small core requires the ACK right
before re-enabling counters in the NMI handler, otherwise a stale PEBS
record may be dumped into the later NMI handler, which trigger the
warning.
Add a new mid_ack flag to track the case. Add all PMI handler bits in
the struct x86_hybrid_pmu to track the bits for different types of
PMUs. Apply mid ACK for the small cores on an Alder Lake machine.
The existing hybrid() macro has a compile error when taking address of
a bit-field variable. Add a new macro hybrid_bit() to get the
bit-field value of a given PMU.
Fixes: f83d2f91d259 ("perf/x86/intel: Add Alder Lake Hybrid support")
Reported-by: Ammy Yi <[email protected]>
Signed-off-by: Kan Liang <[email protected]>
Signed-off-by: Peter Zijlstra (Intel) <[email protected]>
Reviewed-by: Andi Kleen <[email protected]>
Tested-by: Ammy Yi <[email protected]>
Link: https://lkml.kernel.org/r/[email protected]
|
|
gpio-lookup tables
The gpiod_lookup_table.table passed to gpiod_add_lookup_table() must
be terminated with an empty entry, add this.
Note we have likely been getting away with this not being present because
the GPIO lookup code first matches on the dev_id, causing most lookups to
skip checking the table and the lookups which do check the table will
find a matching entry before reaching the end. With that said, terminating
these tables properly still is obviously the correct thing to do.
Fixes: f8eb0235f659 ("x86: pcengines apuv2 gpio/leds/keys platform driver")
Signed-off-by: Hans de Goede <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
360 degree hinges devices with dual KIOX010A + KIOX020A accelerometers
always have both a KIOX010A and a KIOX020A ACPI device (one for each
accel).
Theoretical some vendor may re-use some DSDT for a non-convertible
stripping out just the KIOX020A ACPI device from the DSDT. Check that
both ACPI devices are present to make the check more robust.
Fixes: 153cca9caa81 ("platform/x86: Add and use a dual_accel_detect() helper")
Signed-off-by: Hans de Goede <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
On s390, the following build warning occurs:
drivers/net/ethernet/marvell/mvpp2/mvpp2.h:844:2: warning: overflow in
conversion from 'long unsigned int' to 'int' changes value from
'18446744073709551584' to '-32' [-Woverflow]
844 | ((total_size) - MVPP2_SKB_HEADROOM - MVPP2_SKB_SHINFO_SIZE)
This happens because MVPP2_SKB_SHINFO_SIZE, which is 320 bytes (which is
already 64-byte aligned) on some architectures, actually gets ALIGN'd up
to 512 bytes in the s390 case.
So then, when this is invoked:
MVPP2_RX_MAX_PKT_SIZE(MVPP2_BM_SHORT_FRAME_SIZE)
...that turns into:
704 - 224 - 512 == -32
...which is not a good frame size to end up with! The warning above is a
bit lucky: it notices a signed/unsigned bad behavior here, which leads
to the real problem of a frame that is too short for its contents.
Increase MVPP2_BM_SHORT_FRAME_SIZE by 32 (from 704 to 736), which is
just exactly big enough. (The other values can't readily be changed
without causing a lot of other problems.)
Fixes: 07dd0a7aae7f ("mvpp2: add basic XDP support")
Cc: Sven Auhagen <[email protected]>
Cc: Matteo Croce <[email protected]>
Cc: David S. Miller <[email protected]>
Signed-off-by: John Hubbard <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Add the missing RxUnicast counter.
Fixes: b8f126a8d543 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: DENG Qingfang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Previous atomic increment/decrement logic expects the atomic count to be
'0' after the final decrement.
Replacing atomic count with refcount does not allow that, as
refcount_dec() considers count of 1 as underflow and triggers a kernel
splat.
Fix the current refcount logic by using the usual pattern of decrementing
the refcount and test if it is '0' on the final deref in
c4iw_destroy_cq(). Use wait_for_completion() instead of wait_event().
Fixes: 7183451f846d ("RDMA/cxgb4: Use refcount_t instead of atomic_t for reference counting")
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dakshaja Uppalapati <[email protected]>
Reviewed-by: Potnuri Bharat Teja <[email protected]>
Signed-off-by: Jason Gunthorpe <[email protected]>
|
|
https://gitlab.freedesktop.org/agd5f/linux into drm-fixes
amd-drm-fixes-5.14-2021-08-05:
amdgpu:
- Fix potential out-of-bounds read when updating GPUVM mapping
- Renoir powergating fix
- Yellow Carp updates
- 8K fix for navi1x
- Beige Goby updates and new DIDs
- Fix DMUB firmware version output
- EDP fix
- pmops config fix
Signed-off-by: Dave Airlie <[email protected]>
From: Alex Deucher <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Add device ids.
Signed-off-by: Chengming Gui <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
DMUB firmware info is printed before it gets initialized.
Correct this order to ensure true value is conveyed.
Signed-off-by: Shirish S <[email protected]>
Reviewed-by: Alex Deucher <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
Cc: [email protected]
|
|
[Why]
HPD disable and enable sequences are not mutually exclusive
on Linux. For HPDs that spans over 1s (i.e. HPD low = 1s),
part of the disable sequence (specifically, a request to SMU
to lower refclk) could come right before the call to PHY
enable, causing DMUB to access an unresponsive PHY
and thus a hard hang on the system.
[How]
Disable 48mhz refclk off on native DP.
Reviewed-by: Hersen Wu <[email protected]>
Acked-by: Aurabindo Pillai <[email protected]>
Signed-off-by: Qingqing Zhuo <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
[Why] On S4 resume we also need to fix detection of when to reload DMCUB
firmware because we're currently using the VBIOS version which isn't
compatible with the driver version.
[How] Update the hardware init check for DCN31 since it's the ASIC that
has this issue.
Reviewed-by: Nicholas Kazlauskas <[email protected]>
Acked-by: Aurabindo Pillai <[email protected]>
Signed-off-by: Jude Shih <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
[Why&How]
Hardware team suggested to use SRExitTime= 35.5us as w/a to prevent
underflow in certain modes.
Reviewed-by: Martin Leung <[email protected]>
Acked-by: Aurabindo Pillai <[email protected]>
Signed-off-by: Bing Guo <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
Why:
In DCN2x, HW doesn't automatically divide MASTER_UPDATE_LOCK_DB_X
by the number of pipes ODM Combined.
How:
Set MASTER_UPDATE_LOCK_DB_X to the value that is adjusted by the
number of pipes ODM Combined.
Reviewed-by: Martin Leung <[email protected]>
Acked-by: Aurabindo Pillai <[email protected]>
Signed-off-by: Bing Guo <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
[WHY]
For DCN31 onward, LTTPR is to be enabled and set to Transparent by
VBIOS. Driver is to assume that VBIOS has done this without needing to
check the VBIOS interop bit.
[HOW]
Add LTTPR enable and interop VBIOS bits into dc->caps, and force-set the
interop bit to true for DCN31+.
Reviewed-by: Jun Lei <[email protected]>
Acked-by: Aurabindo Pillai <[email protected]>
Signed-off-by: Wesley Chalmers <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|