| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Inverse the logic for printing the debug message.
In mmc_decode_ext_csd() print message when MAN_BKOPS_EN is set
Signed-off-by: Uri Yanai <[email protected]>
Signed-off-by: Alex Lemberg <[email protected]>
Signed-off-by: Ulf Hansson <[email protected]>
|
|
Add support for HS400 mode.
The driver still misses support for tuning, therefore
highspeed modes like HS400 might not work under all
circumstances yet.
Successfully tested on a Odroid C2 (S905 GXBB).
Signed-off-by: Heiner Kallweit <[email protected]>
Reviewed-by: Kevin Hilman <[email protected]>
Tested-by: Kevin Hilman <[email protected]>
Signed-off-by: Ulf Hansson <[email protected]>
|
|
The remove callback is called only if probe finished successfully.
Therefore these checks are not needed.
Signed-off-by: Heiner Kallweit <[email protected]>
Reviewed-by: Kevin Hilman <[email protected]>
Tested-by: Kevin Hilman <[email protected]>
Signed-off-by: Ulf Hansson <[email protected]>
|
|
A bounce buffer of 512K isn't needed as the max request size is
511 * 512 byte.
Signed-off-by: Heiner Kallweit <[email protected]>
Reviewed-by: Kevin Hilman <[email protected]>
Tested-by: Kevin Hilman <[email protected]>
Signed-off-by: Ulf Hansson <[email protected]>
|
|
So far max_blk_count isn't set what results in a default of value 8
to be used (PAGE_SIZE / block size).
Block length field has 9 bits, so set max_blk_count to 2^9-1 = 511.
In addition set max_req_size because max_blk_count is also limited
by max_req_size / block_size.
Signed-off-by: Heiner Kallweit <[email protected]>
Reviewed-by: Kevin Hilman <[email protected]>
Tested-by: Kevin Hilman <[email protected]>
Acked-by: Kevin Hilman <[email protected]>
Signed-off-by: Ulf Hansson <[email protected]>
|
|
Disabling and immediately re-enabling interrupts in meson_mmc_request
doesn't provide a benefit. Instead enable interrupts in probe already.
And disable interrupts in remove, this was missing so far.
Signed-off-by: Heiner Kallweit <[email protected]>
Reviewed-by: Kevin Hilman <[email protected]>
Signed-off-by: Ulf Hansson <[email protected]>
|
|
Remove unneeded variable ret and simplify the if block.
Signed-off-by: Heiner Kallweit <[email protected]>
Acked-by: Kevin Hilman <[email protected]>
Signed-off-by: Ulf Hansson <[email protected]>
|
|
The following changes are quite small, therefore I combined them in
one patch.
- ret doesn't need to be initialized with 0
- use standard !clk_rate notation to check for a zero value
- If clk_rate is zero we return here. Therefore all further checks
in this function for clk_rate != 0 are not needed.
- switch from dev_warn to dev_err if the clock can't be set
- If due to clock source and available divider values the requested
frequency isn't matched exactly (always the case if requested
frequency is 52 MHz), then just print the differing values as
debug message and not as warning.
- Also remove ret from the message as it is always 0.
- Set member current_clock to the current requested rate and
mmc->actual_clock to the current actual rate
Signed-off-by: Heiner Kallweit <[email protected]>
Signed-off-by: Ulf Hansson <[email protected]>
|
|
val isn't used in the switch clause and afterwards there's an
identical statement. So remove it.
In case of an unexpected bus width the error message indicates
the intention to set the bus width to 4 and to go on.
So remove the return statement. This return statement also
conflicts with "setting to 4" because nothing would be set
actually before returning. 4bit bus width are chosen as
default as the vendor driver does it too.
Signed-off-by: Heiner Kallweit <[email protected]>
Acked-by: Kevin Hilman <[email protected]>
Signed-off-by: Ulf Hansson <[email protected]>
|
|
The current code dealing with calculating mmc->f_min is a bit complicated.
Additionally, the attempt to set an initial clock rate should explicitly
use a rate between 100KHz to 400 KHz, according the (e)MMC/SD specs, which
it doesn't.
Fix the problem and clean up the code by using clk_round_rate() to pick the
nearest minimum rate to 400KHz (rounded down from 400kHz).
Signed-off-by: Ulf Hansson <[email protected]>
[Heiner: Changed from 100KHz to 400KHz to get a proper rounded rate]
Signed-off-by: Heiner Kallweit <[email protected]>
|
|
This function is doing to many clever things at the same time under
too many various conditions.
Start to make things clearer by refactoring: break out the
finalization of the previous asynchronous request to its own
function mmc_finalize_areq(). We can get rid of the default
assignment of status and let the call deal with this.
Signed-off-by: Linus Walleij <[email protected]>
Signed-off-by: Ulf Hansson <[email protected]>
|
|
The return value from blk_end_request() is a bool but is
treated like an int. This is generally safe, but the variable
also has the opaque name "ret" and gets returned from the
helper function mmc_blk_cmd_err().
- Switch the variable to a bool, applies everywhere.
- Return a bool from mmc_blk_cmd_err() and rename the function
mmc_blk_rw_cmd_err() to indicate through the namespace that
this is a helper for mmc_blk_issue_rw_rq().
- Rename the variable from "ret" to "req_pending" inside the
while() loop inside mmc_blk_issue_rq_rq(), which finally
makes it very clear what this while loop is waiting for.
- Augment the argument "ret" to mmc_blk_rq_cmd_err() to
old_req_pending so it becomes evident that this is an
older state, and it is returned only if we fail to get
the number of written blocks from an SD card in the
function mmc_sd_num_wr_blocks().
- Augment the while() loop in mmc_blk_rq_cmd_abort(): it
is evident now that we know this is a bool variable,
that the function is just spinning waiting for
blk_end_request() to return false.
Signed-off-by: Linus Walleij <[email protected]>
Signed-off-by: Ulf Hansson <[email protected]>
|
|
mmc_sd_num_wr_blocks() has an interesting construction that
saves one return argument by casting (u32)-1 as error code
if something goes wrong.
This is however a bit confusing when the normal kernel
pattern is to return an int error code on success.
So instead pass a variable "blocks" that the function can
fill in with the number of successfully transferred blocks
and return an integer as error code.
Signed-off-by: Linus Walleij <[email protected]>
Signed-off-by: Ulf Hansson <[email protected]>
[Ulf: Changed a return code to -EIO, reported by Dan Carpenter and fixed
by Linus Walleij]
|
|
By default, the DMA mask covers only the low 32-bit address space, which
causes SWIOTLB on arm64 to fall back to a bounce buffer for DMA
transfers involving memory outside the 32-bit address space.
The R-Car DMA controller hardware supports a 40-bit address space, hence
widen the DMA mask to 40 bits to actually make use of this feature.
Signed-off-by: Geert Uytterhoeven <[email protected]>
Signed-off-by: Vinod Koul <[email protected]>
|
|
Commit 577fb13199b1 ("mmc: rework selection of bus speed mode")
refactored bus width selection code to mmc_select_bus_width().
However, it also altered the behavior to not call the selection code in
non-high-speed modes anymore.
This causes 1-bit mode to always be used when the high-speed mode is not
enabled, even though 4-bit and 8-bit bus are valid bus widths in the
backwards-compatibility (legacy) mode as well (see e.g. 5.3.2 Bus Speed
Modes in JEDEC 84-B50). This results in a significant regression in
transfer speeds.
Fix the code to allow 4-bit and 8-bit widths even without high-speed
mode, as before.
Tested with a Zynq-7000 PicoZed 7020 board.
Fixes: 577fb13199b1 ("mmc: rework selection of bus speed mode")
Signed-off-by: Anssi Hannula <[email protected]>
Cc: <[email protected]>
Signed-off-by: Ulf Hansson <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/core
Pull perf/core improvements and fixes from Arnaldo Carvalho de Melo:
New features:
- Introduce the 'delta-abs' 'perf diff' compute method, that orders the
histogram entries by the absolute value of the percentage delta for a
function in two perf.data files, i.e. the functions that changed the
most (increase or decrease in samples) comes first (Namhyung Kim)
User visible changes:
- Improve message about tweaking the kernel.perf_event_paranoid setting,
telling how to make the change permanent by editing /etc/sysctl.conf
(Arnaldo Carvalho de Melo)
Infrastructure changes:
- Introduce linux/compiler-gcc.h as a counterpart to the kernel's,
initially containing the definition of __fallthrough, more to
come (__maybe_unused, etc) (Arnaldo Carvalho de Melo)
- Fixes for problems uncovered by building tools/perf with clang, such
as always true tests of arrays against NULL and variables that sometimes
were used without being initialized (Arnaldo Carvalho de Melo, Steven Rostedt)
- Before loading a new ELF, clear global variables set by the
samples/bpf loader (Mickaël Salaün)
- Ignore already processed ELF sections in the samples/bpf
loader (Mickaël Salaün)
- Fix compile error in the scripting code with some perl5
versions (Wang YanQing)
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
Signed-off-by: Ingo Molnar <[email protected]>
|
|
Signed-off-by: Ingo Molnar <[email protected]>
|
|
Herbert Xu says:
====================
rhashtable: Handle table allocation failure during insertion
v2 -
Added Ack to patch 2.
Fixed RCU annotation in code path executed by rehasher by using
rht_dereference_bucket.
v1 -
This series tackles the problem of table allocation failures during
insertion. The issue is that we cannot vmalloc during insertion.
This series deals with this by introducing nested tables.
The first two patches removes manual hash table walks which cannot
work on a nested table.
The final patch introduces nested tables.
I've tested this with test_rhashtable and it appears to work.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
This patch adds code that handles GFP_ATOMIC kmalloc failure on
insertion. As we cannot use vmalloc, we solve it by making our
hash table nested. That is, we allocate single pages at each level
and reach our desired table size by nesting them.
When a nested table is created, only a single page is allocated
at the top-level. Lower levels are allocated on demand during
insertion. Therefore for each insertion to succeed, only two
(non-consecutive) pages are needed.
After a nested table is created, a rehash will be scheduled in
order to switch to a vmalloced table as soon as possible. Also,
the rehash code will never rehash into a nested table. If we
detect a nested table during a rehash, the rehash will be aborted
and a new rehash will be scheduled.
Signed-off-by: Herbert Xu <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
There are two problems with the function tipc_sk_reinit. Firstly
it's doing a manual walk over an rhashtable. This is broken as
an rhashtable can be resized and if you manually walk over it
during a resize then you may miss entries.
Secondly it's missing memory barriers as previously the code used
spinlocks which provide the barriers implicitly.
This patch fixes both problems.
Fixes: 07f6c4bc048a ("tipc: convert tipc reference table to...")
Signed-off-by: Herbert Xu <[email protected]>
Acked-by: Ying Xue <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The function glock_hash_walk walks the rhashtable by hand. This
is broken because if it catches the hash table in the middle of
a rehash, then it will miss entries.
This patch replaces the manual walk by using the rhashtable walk
interface.
Fixes: 88ffbf3e037e ("GFS2: Use resizable hash table for glocks")
Signed-off-by: Herbert Xu <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
When sending ARP requests over AX.25 links the hwaddress in the neighbour
cache are not getting initialized. For such an incomplete arp entry
ax2asc2 will generate an empty string resulting in /proc/net/arp output
like the following:
$ cat /proc/net/arp
IP address HW type Flags HW address Mask Device
192.168.122.1 0x1 0x2 52:54:00:00:5d:5f * ens3
172.20.1.99 0x3 0x0 * bpq0
The missing field will confuse the procfs parsing of arp(8) resulting in
incorrect output for the device such as the following:
$ arp
Address HWtype HWaddress Flags Mask Iface
gateway ether 52:54:00:00:5d:5f C ens3
172.20.1.99 (incomplete) ens3
This changes the content of /proc/net/arp to:
$ cat /proc/net/arp
IP address HW type Flags HW address Mask Device
172.20.1.99 0x3 0x0 * * bpq0
192.168.122.1 0x1 0x2 52:54:00:00:5d:5f * ens3
To do so it change ax2asc to put the string "*" in buf for a NULL address
argument. Finally the HW address field is left aligned in a 17 character
field (the length of an ethernet HW address in the usual hex notation) for
readability.
Signed-off-by: Ralf Baechle <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This patch fixes an issue where the type of counters in the queue(s)
and interface are not in sync (queue counters are int, interface
counters are long), causing incorrect reporting of tx/rx values
of the vif interface and unclear counter overflows.
This patch sets both counters to the u64 type.
Signed-off-by: Mart van Santen <[email protected]>
Reviewed-by: Paul Durrant <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Simple cleanup to use the new APIs.
Signed-off-by: Christoph Hellwig <[email protected]>
Acked-by: Don Brace <[email protected]>
Tested-by: Don Brace <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
There are two reasons for reporting wakeup event when dedicated wakeup
IRQ is triggered:
- wakeup events accounting, so proper statistical data will be
displayed in sysfs and debugfs;
- there are small window when System is entering suspend during which
dedicated wakeup IRQ can be lost:
dpm_suspend_noirq()
|- device_wakeup_arm_wake_irqs()
|- dev_pm_arm_wake_irq(X)
|- IRQ is enabled and marked as wakeup source
[1]...
|- suspend_device_irqs()
|- suspend_device_irq(X)
|- irqd_set(X, IRQD_WAKEUP_ARMED);
|- wakup IRQ armed
The wakeup IRQ can be lost if it's triggered at point [1]
and not armed yet.
Hence, fix above cases by adding simple pm_wakeup_event() call in
handle_threaded_wake_irq().
Fixes: 4990d4fe327b (PM / Wakeirq: Add automated device wake IRQ handling)
Signed-off-by: Grygorii Strashko <[email protected]>
Tested-by: Keerthy <[email protected]>
[ [email protected]: added missing return to avoid warnings ]
Tested-by: Tony Lindgren <[email protected]>
Signed-off-by: Tony Lindgren <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
Dedicated wakeirq is a one time event to wake-up the system from
low-power state and then call pm_runtime_resume() on the device wired
with the dedicated wakeirq.
Sometimes dedicated wakeirqs can get deferred if they trigger after we
call disable_irq_nosync() in dev_pm_disable_wake_irq(). This can happen
if pm_runtime_get() is called around the same time a wakeirq fires.
If an interrupt fires after disable_irq_nosync(), by default it will get
tagged with IRQS_PENDING and will run later on when the interrupt is
enabled again.
Deferred wakeirqs usually just produce pointless wake-up events. But they
can also cause suspend to fail if the deferred wakeirq fires during
dpm_suspend_noirq() for example. So we really don't want to see the
deferred wakeirqs triggering after the device has resumed.
Let's fix the issue by setting IRQ_DISABLE_UNLAZY flag for the dedicated
wakeirqs. The other option would be to implement irq_disable() in the
dedicated wakeirq controller, but that's not a generic solution.
For reference below is what happens with a IRQ_TYPE_EDGE_BOTH IRQ
type wakeirq:
- resume by dedicated IRQ (EDGE_FALLING)
- suspend_enter()
....
- arch_suspend_enable_irqs()
|- dedicated IRQ armed and fired
|- irq_pm_check_wakeup()
|- disarm, disable IRQ and mark as IRQS_PENDING
....
- dpm_resume_noirq()
|- resume_device_irqs()
|- __enable_irq()
|- check_irq_resend()
|- handle_threaded_wake_irq()
|- dedicated IRQ processed
|- device_wakeup_disarm_wake_irqs()
|- disable_irq_wake()
....
!-> dedicated IRQ (EDGE_RISING)
-| handle_edge_irq()
|- IRQ disabled: mask_ack_irq and mark as IRQS_PENDING
....
- subsequent suspend
....
|- dpm_suspend_noirq()
|- device_wakeup_arm_wake_irqs()
|- __enable_irq()
|- check_irq_resend()
(a) |- handle_threaded_wake_irq()
|- pm_wakeup_event() --> abort suspend
....
|- suspend_device_irqs()
|- suspend_device_irq()
|- dedicated IRQ armed
....
(b) |- resend_irqs
|- irq_pm_check_wakeup()
|- IRQ armed -> abort suspend
because of pending IRQ System suspend can be aborted at points
(a)-not armed or (b)-armed.
Fixes: 4990d4fe327b (PM / Wakeirq: Add automated device wake IRQ handling)
Signed-off-by: Grygorii Strashko <[email protected]>
[ [email protected]: added a comment, updated the description ]
Tested-by: Tony Lindgren <[email protected]>
Signed-off-by: Tony Lindgren <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
We currently rely on runtime PM to enable dedicated wakeirq for suspend.
This assumption fails in the following two cases:
1. If the consumer driver does not have runtime PM implemented, the
dedicated wakeirq never gets enabled for suspend
2. If the consumer driver has runtime PM implemented, but does not idle
in suspend
Let's fix the issue by always enabling the dedicated wakeirq during
suspend.
Depends-on: bed570307ed7 (PM / wakeirq: Fix dedicated wakeirq for drivers not using autosuspend)
Fixes: 4990d4fe327b (PM / Wakeirq: Add automated device wake IRQ handling)
Reported-by: Keerthy <[email protected]>
Tested-by: Keerthy <[email protected]>
Signed-off-by: Grygorii Strashko <[email protected]>
[ [email protected]: updated based on bed570307ed7, added description ]
Tested-by: Tony Lindgren <[email protected]>
Signed-off-by: Tony Lindgren <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
This adds a new auxiliary record MODULE_INIT to the SYSCALL event.
We get finit_module for free since it made most sense to hook this in to
load_module().
https://github.com/linux-audit/audit-kernel/issues/7
https://github.com/linux-audit/audit-kernel/wiki/RFE-Module-Load-Record-Format
Signed-off-by: Richard Guy Briggs <[email protected]>
Acked-by: Jessica Yu <[email protected]>
[PM: corrected links in the commit description]
Signed-off-by: Paul Moore <[email protected]>
|
|
Before loading a new ELF, clean previous kernel version, license and
processed sections.
Signed-off-by: Mickaël Salaün <[email protected]>
Acked-by: Joe Stringer <[email protected]>
Acked-by: Wang Nan <[email protected]>
Cc: Alexei Starovoitov <[email protected]>
Cc: Daniel Borkmann <[email protected]>
Cc: David S. Miller <[email protected]>
Cc: [email protected]
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
Add a missing check for the map fixup loop.
Signed-off-by: Mickaël Salaün <[email protected]>
Acked-by: Joe Stringer <[email protected]>
Acked-by: Wang Nan <[email protected]>
Cc: Alexei Starovoitov <[email protected]>
Cc: Daniel Borkmann <[email protected]>
Cc: David S. Miller <[email protected]>
Cc: [email protected]
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
Include unistd.h to define __NR_getuid and __NR_getsid.
Signed-off-by: Mickaël Salaün <[email protected]>
Acked-by: Joe Stringer <[email protected]>
Acked-by: Wang Nan <[email protected]>
Cc: Alexei Starovoitov <[email protected]>
Cc: Daniel Borkmann <[email protected]>
Cc: David S. Miller <[email protected]>
Cc: [email protected]
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
As it will always evaluate to 'true', as reported by clang:
util/map.c:390:36: error: address of array 'map->dso->name' will always evaluate to 'true' [-Werror,-Wpointer-bool-conversion]
if (map && map->dso && (map->dso->name || map->dso->long_name)) {
~~~~~~~~~~^~~~ ~~
util/map.c:393:22: error: address of array 'map->dso->name' will always evaluate to 'true' [-Werror,-Wpointer-bool-conversion]
else if (map->dso->name)
~~ ~~~~~~~~~~^~~~
Cc: Adrian Hunter <[email protected]>
Cc: David Ahern <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Wang Nan <[email protected]>
Link: http://lkml.kernel.org/n/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
It will always evaluate to 'true', as clang warns:
CC /tmp/build/perf/tests/perf-record.o
CC /tmp/build/perf/tests/evsel-roundtrip-name.o
tests/perf-record.c:69:24: error: comparison of array 'argv' equal to a null pointer is always false [-Werror,-Wtautological-pointer-compare]
if (evlist == NULL || argv == NULL) {
^~~~ ~~~~
1 error generated.
Cc: Adrian Hunter <[email protected]>
Cc: David Ahern <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Wang Nan <[email protected]>
Link: http://lkml.kernel.org/n/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
As it is an array, so will always evaluate to 'true', as reported by
clang:
builtin-sched.c:2070:19: error: address of array 'sym->name' will always evaluate to 'true' [-Werror,-Wpointer-bool-conversion]
if (sym && sym->name) {
~~ ~~~~~^~~~
1 warning generated.
So just ditch all those useless checks.
Cc: Adrian Hunter <[email protected]>
Cc: David Ahern <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Wang Nan <[email protected]>
Link: http://lkml.kernel.org/n/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
When a tool can't open counters due to the kernel.perf_event_paranoit
sysctl setting, we inform how to tweak it to allow the operation to
succeed, in addition to that, suggest setting /etc/sysctl.conf to
make the setting permanent.
Suggested-by: Ingo Molnar <[email protected]>
Cc: Adrian Hunter <[email protected]>
Cc: David Ahern <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Wang Nan <[email protected]>
Link: http://lkml.kernel.org/n/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
Detected with clang:
CC /tmp/build/perf/plugin_function.o
plugin_function.c:145:6: warning: variable 'index' is used uninitialized whenever 'if' condition is false [-Wsometimes-uninitialized]
if (parent && ftrace_indent->set)
^~~~~~~~~~~~~~~~~~~~~~~~~~~~
plugin_function.c:148:29: note: uninitialized use occurs here
trace_seq_printf(s, "%*s", index*3, "");
^~~~~
plugin_function.c:145:2: note: remove the 'if' if its condition is always true
if (parent && ftrace_indent->set)
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
plugin_function.c:145:6: warning: variable 'index' is used uninitialized whenever '&&' condition is false [-Wsometimes-uninitialized]
if (parent && ftrace_indent->set)
^~~~~~
plugin_function.c:148:29: note: uninitialized use occurs here
trace_seq_printf(s, "%*s", index*3, "");
^~~~~
plugin_function.c:145:6: note: remove the '&&' if its condition is always true
if (parent && ftrace_indent->set)
^~~~~~~~~
plugin_function.c:133:11: note: initialize the variable 'index' to silence this warning
int index;
^
= 0
2 warnings generated.
Reviewed-by: Steven Rostedt (VMware) <[email protected]>
Cc: Adrian Hunter <[email protected]>
Cc: David Ahern <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Wang Nan <[email protected]>
Link: http://lkml.kernel.org/n/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
A undefined value was being used for the OLD_RING_BUFFER_TYPE_TIME_STAMP
case entry, as the 'length' variable was not being initialized, fix it.
Caught by the reporter when building tools/perf/ using clang, which emmitted
this warning:
kbuffer-parse.c:312:7: warning: variable 'length' is used uninitialized whenever switch case is taken [-Wsometimes-uninitialized]
case OLD_RINGBUF_TYPE_TIME_EXTEND:
^~~~~~~~~~~~~~~~~~~~~~~~~~~~
kbuffer-parse.c:339:29: note: uninitialized use occurs here
kbuf->next = kbuf->index + length;
^~~~~~
kbuffer-parse.c:297:21: note: initialize the variable 'length' to silence this warning
unsigned int length;
^
= 0
Reported-by: Arnaldo Carvalho de Melo <[email protected]>
Signed-off-by: Steven Rostedt <[email protected]>
Cc: Adrian Hunter <[email protected]>
Cc: David Ahern <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Wang Nan <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
Fix below compile error:
CC util/scripting-engines/trace-event-perl.o
In file included from /usr/lib/perl5/5.22.2/i686-linux/CORE/perl.h:5673:0,
from util/scripting-engines/trace-event-perl.c:31:
/usr/lib/perl5/5.22.2/i686-linux/CORE/inline.h: In function 'S__is_utf8_char_slow':
/usr/lib/perl5/5.22.2/i686-linux/CORE/inline.h:270:5: error: nested extern declaration of 'Perl___notused' [-Werror=nested-externs]
dTHX; /* The function called below requires thread context */
^
cc1: all warnings being treated as errors
After digging perl5 repository, I find out that we will meet this
compile error with perl from v5.21.1 to v5.25.4
Signed-off-by: Wang YanQing <[email protected]>
Acked-by: Jiri Olsa <[email protected]>
Link: http://lkml.kernel.org/r/20170212024655.GA15997@udknight
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
My opensource.altera.com email will be going away soon. Switch to new
email address (linux.intel.com).
Signed-off-by: Thor Thayer <[email protected]>
Cc: linux-edac <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Borislav Petkov <[email protected]>
|
|
With the IRQ stack changes integrated, the XRX200 devices started
emitting a constant stream of kernel messages like this:
[ 565.415310] Spurious IRQ: CAUSE=0x1100c300
This is caused by IP0 getting handled by plat_irq_dispatch() rather than
its vectored interrupt handler, which is fixed by commit de856416e714
("MIPS: IRQ Stack: Fix erroneous jal to plat_irq_dispatch").
Fix plat_irq_dispatch() to handle non-vectored IPI interrupts correctly
by setting up IP2-6 as proper chained IRQ handlers and calling do_IRQ
for all MIPS CPU interrupts.
Signed-off-by: Felix Fietkau <[email protected]>
Acked-by: John Crispin <[email protected]>
Cc: [email protected]
Patchwork: https://patchwork.linux-mips.org/patch/15077/
[[email protected]: tweaked commit message]
Signed-off-by: James Hogan <[email protected]>
|
|
Since commit 4bcc595ccd80 ("printk: reinstate KERN_CONT for printing
continuation lines") the output of counter synchornisation has been
split across lines:
[ 0.665181] Synchronize counters for CPU 1:
[ 0.678578] done.
Fix this by using pr_cont, and replace printk with pr_info.
Signed-off-by: Matt Redfearn <[email protected]>
Cc: Ralf Baechle <[email protected]>
Cc: [email protected]
Patchwork: https://patchwork.linux-mips.org/patch/15195/
Signed-off-by: James Hogan <[email protected]>
|
|
Commit dda45f701c9d ("MIPS: Switch to the irq_stack in interrupts")
changed both the normal and vectored interrupt handlers. Unfortunately
the vectored version, "except_vec_vi_handler", was incorrectly modified
to unconditionally jal to plat_irq_dispatch, rather than doing a jalr to
the vectored handler that has been set up. This is ok for many platforms
which set the vectored handler to plat_irq_dispatch anyway, but will
cause problems with platforms that use other handlers.
Fixes: dda45f701c9d ("MIPS: Switch to the irq_stack in interrupts")
Signed-off-by: Matt Redfearn <[email protected]>
Cc: Ralf Baechle <[email protected]>
Cc: Paul Burton <[email protected]>
Cc: [email protected]
Patchwork: https://patchwork.linux-mips.org/patch/15110/
Signed-off-by: James Hogan <[email protected]>
|
|
The postlink Makefile must include include/config/auto.conf to get the
kernel configuration variables. But in a clean kernel directory this
file does not exist, causing make to bail with the error:
arch/mips/Makefile.postlink:10: include/config/auto.conf: No such file or directory
make[1]: *** No rule to make target 'include/config/auto.conf'. Stop.
Makefile:1290: recipe for target 'vmlinuxclean' failed
Fix this by using "-include" to not cause a Make error when the file
does not exist.
Fixes: 44079d3509ae ("MIPS: Use Makefile.postlink to insert relocations into vmlinux")
Signed-off-by: Matt Redfearn <[email protected]>
Cc: Ralf Baechle <[email protected]>
Cc: [email protected]
Patchwork: https://patchwork.linux-mips.org/patch/15136/
Signed-off-by: James Hogan <[email protected]>
|
|
The recently added MIPS cacheinfo support used a macro populate_cache()
to populate the cacheinfo structures depending on which caches are
present. However the macro contains multiple statements without
enclosing them in a do {} while (0) loop, so the L2 and L3 cache
conditionals in populate_cache_leaves() only conditionalised the first
statement in the macro.
This overflows the buffer allocated by detect_cache_attributes(),
resulting in boot failures under QEMU where neither the L2 or L2 caches
are present.
Enclose the macro statements in a do {} while (0) block to keep the
whole macro inside the conditionals.
Fixes: ef462f3b64e9 ("MIPS: Add cacheinfo support")
Reported-by: Guenter Roeck <[email protected]>
Signed-off-by: James Hogan <[email protected]>
Tested-by: Guenter Roeck <[email protected]>
Cc: Ralf Baechle <[email protected]>
Cc: Justin Chen <[email protected]>
Cc: Florian Fainelli <[email protected]>
Cc: [email protected]
Cc: [email protected]
Patchwork: https://patchwork.linux-mips.org/patch/15276/
|
|
When building for microMIPS we need to ensure that the assembler always
knows that there is code at the target of a branch or jump. Commit
7170bdc77755 ("MIPS: Add return errors to protected cache ops")
introduced a fixup path to protected_cache(e)_op() which does not meet
this requirement. The fixup path jumps to the "2" label but the .section
pseudo-op immediately following it causes the label to be marked as
data. Linking then fails with:
mips-img-linux-gnu-ld: arch/mips/mm/c-r4k.o: .fixup+0x0: Unsupported
jump between ISA modes; consider recompiling with interlinking
enabled.
Fix this by declaring that "2" labels code using the .insn directive.
Fixes: 7170bdc77755 ("MIPS: Add return errors to protected cache ops")
Signed-off-by: Paul Burton <[email protected]>
Signed-off-by: James Hogan <[email protected]>
Reviewed-by: Maciej W. Rozycki <[email protected]>
Cc: [email protected]
Cc: Ralf Baechle <[email protected]>
Patchwork: https://patchwork.linux-mips.org/patch/15274/
Signed-off-by: James Hogan <[email protected]>
|
|
MIPS dependencies for KVM
Miscellaneous MIPS architecture changes depended on by the MIPS KVM
changes in the KVM tree.
- Move pgd_alloc() out of header.
- Exports so KVM can access page table management and TLBEX functions.
- Add return errors to protected cache ops.
|
|
The code sets the default return code to -ENOSYS but then overrides this
to -EINVAL in the switch() statement's default case, which is clearly
silly.
This patch removes the override and sets the default return code to
-ENOTTY, which is the conventional return for an unimplemented ioctl.
Signed-off-by: Paul Durrant <[email protected]>
Signed-off-by: Boris Ostrovsky <[email protected]>
|
|
Commit a92e7c3d82a1 ("spi: s3c64xx: consider the case when the CS
line is not connected") introduced an inconsistency between the
binding, where the disconnected CS line was marked as
'no-cs-readback', and the driver.
The driver is erroneously checking for that attribute with
property name of 'broken-cs'.
Check for 'no-cs-readback' in the driver as well.
Fixes: a92e7c3d82a1 ("spi: s3c64xx: consider the case when the CS line is not connected")
Signed-off-by: Andi Shyti <[email protected]>
Reviewed-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
Cc: [email protected]
|
|
GCC complains about unused variable 'vma' in mark_screen_rdonly() if THP is
disabled:
arch/x86/kernel/vm86_32.c: In function ‘mark_screen_rdonly’:
arch/x86/kernel/vm86_32.c:180:26: warning: unused variable ‘vma’
[-Wunused-variable]
struct vm_area_struct *vma = find_vma(mm, 0xA0000);
That's silly. pmd_trans_huge() resolves to 0 when THP is disabled, so the
whole block should be eliminated.
Moving the variable declaration outside the if() block shuts GCC up.
Reported-by: Jérémy Lefaure <[email protected]>
Signed-off-by: Kirill A. Shutemov <[email protected]>
Tested-by: Borislav Petkov <[email protected]>
Cc: Carlos O'Donell <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Thomas Gleixner <[email protected]>
|
|
When we check for additional DT properties in the current node we
use the device_node passed in with the configuration data, this
will not point to the correct DT node, use the one passed in
for this purpose.
Fixes: d2a2e729a666 ("regulator: tps65086: Add regulator driver for the TPS65086 PMIC")
Reported-by: Steven Kipisz <[email protected]>
Signed-off-by: Andrew F. Davis <[email protected]>
Tested-by: Steven Kipisz <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
|