| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Goodix GT917S is a new touchscreen chip from Goodix.
Add its compatible string to the device tree binding.
Signed-off-by: Icenowy Zheng <[email protected]>
Acked-by: Rob Herring <[email protected]>
Reviewed-by: Bastien Nocera <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
Some devices with a goodix touchscreen have more then 1 capacitive
touch-key. This commit replaces the current support for a single
touch-key, which ignored the reported key-code. With support for
up to 7 touch-keys, based upon checking the key-code which is
post-fixed to any reported touch-data.
KEY_LEFTMETA is assigned to the first touch-key (it will still be
the default keycode for devices with a single touch-key).
KEY_F1, KEY_F2... are assigned as default keycode for the other
touch-keys.
This commit also add supports for keycode remapping, so that
systemd-udev's hwdb can be used to remap the codes to send
keycodes to match the icons on the buttons for devices with more
then 1 touch-key.
Signed-off-by: Dmitry Mastykin <[email protected]>
Reviewed-by: Bastien Nocera <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
The goodix panel sends spurious interrupts after a 'finger up' event,
which always cause a timeout.
We were exiting the interrupt handler by reporting touch_num == 0, but
this was still processed as valid and caused the code to use the
uninitialised point_data, creating spurious key release events.
Report an error from the interrupt handler so as to avoid processing
invalid point_data further.
Signed-off-by: Dmitry Mastykin <[email protected]>
Reviewed-by: Bastien Nocera <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
On some ACPI/x86 devices (where we use one of the ACPI IRQ pin access
methods) the firmware is buggy, it does not properly reset the controller
at boot, and we cannot communicate with it.
Normally on ACPI/x86 devices we do not want to reset the controller at
probe time since in some cases this causes the controller to loose its
configuration and this is loaded into it by the system's firmware.
So on these systems we leave the reset_controller_at_probe flag unset,
even though we have a access to both the IRQ and reset pins and thus
could reset it.
In the case of the buggy firmware we have to reset the controller to
actually be able to talk to it.
This commit adds a special case for this, if the goodix_i2c_test() fails,
and we have not reset the controller yet; and we do have a way to reset
the controller then retry the i2c-test after resetting the controller.
This fixes the driver failing at probe on ACPI/x86 systems with this
firmware bug.
Reported-and-tested-by: Dmitry Mastykin <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
Some devices, e.g the Trekstor Primetab S11B, lose there config over
a suspend/resume cycle (likely the controller loses power during suspend).
This commit reads back the config version on resume and if matches the
expected config version it resets the controller and resends the config
we read back and saved at probe time.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1786317
BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199207
Reviewed-by: Bastien Nocera <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
Make goodix_send_cfg() take a raw buffer as argument instead of a
struct firmware *cfg, so that it can also be used to restore the config
on resume if necessary.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1786317
BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199207
Reviewed-by: Bastien Nocera <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
Our goodix_check_cfg_* helpers do things like:
int i, raw_cfg_len = cfg->size - 2;
...
if (check_sum != cfg->data[raw_cfg_len]) {
When cfg->size < 2, this will end up indexing the cfg->data array with
a negative value, which will not end well.
To fix this this commit adds a new GOODIX_CONFIG_MIN_LENGTH define and
adds a minimum size check for firmware-config files using this new define.
For consistency this commit also adds a new GOODIX_CONFIG_GT9X_LENGTH for
the length used for recent gt9xx and gt1xxx chips, instead of using
GOODIX_CONFIG_MAX_LENGTH for this, so that if other length defines get
added in the future it will be clear that the MIN and MAX defines should
contain the min and max values of all the other defines.
Signed-off-by: Hans de Goede <[email protected]>
Reviewed-by: Bastien Nocera <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
Save a copy of the config in goodix_read_config(), this is a preparation
patch for restoring the config if it was lost after a supend/resume cycle.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1786317
BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199207
Reviewed-by: Bastien Nocera <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
Move the defines to above the struct goodix_ts_data declaration, so
that the MAX defines can be used inside the struct goodix_ts_data
declaration. No functional changes, just moving a block of code.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1786317
BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199207
Reviewed-by: Bastien Nocera <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
Some Apollo Lake (x86, UEFI + ACPI) devices only list the reset GPIO
in their _CRS table and the bit-banging of the IRQ line necessary to
wake-up the controller from suspend can be done by calling 2 Goodix
custom / specific ACPI methods.
This commit adds support for controlling the IRQ line in this matter,
allowing us to properly suspend the touchscreen controller on such
devices.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1786317
BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199207
Reviewed-by: Bastien Nocera <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
On most Bay Trail (x86, UEFI + ACPI) devices the ACPI tables do not have
a _DSD with a "daffd814-6eba-4d8c-8a91-bc9bbf4aa301" UUID, adding
"irq-gpios" and "reset-gpios" mappings, so we cannot get the GPIOS by name
without first manually adding mappings ourselves.
These devices contain 2 GpioIo resource in their _CRS table, on all 4 such
devices which I have access to, the order of the 2 GPIOs is reset, int.
Note that the GPIO to which the touchscreen controller irq pin is connected
is configured in direct-irq mode on these Bay Trail devices, the
pinctrl-baytrail.c driver still allows controlling the pin as a GPIO in
this case, but this is not necessarily the case on other X86 ACPI
platforms, nor do we have a guarantee that the GPIO order is the same
elsewhere, so we limit the use of a _CRS table with 2 GpioIo resources
to Bay Trail devices only.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1786317
BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199207
Reviewed-by: Bastien Nocera <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
devices
On most Cherry Trail (x86, UEFI + ACPI) devices the ACPI tables do not have
a _DSD with a "daffd814-6eba-4d8c-8a91-bc9bbf4aa301" UUID, adding
"irq-gpios" and "reset-gpios" mappings, so we cannot get the GPIOS by name
without first manually adding mappings ourselves.
These devices contain 1 GpioInt and 1 GpioIo resource in their _CRS table:
Method (_CRS, 0, NotSerialized) // _CRS: Current Resource Settings
{
Name (RBUF, ResourceTemplate ()
{
I2cSerialBusV2 (0x0014, ControllerInitiated, 0x00061A80,
AddressingMode7Bit, "\\_SB.PCI0.I2C2",
0x00, ResourceConsumer, , Exclusive,
)
GpioInt (Edge, ActiveLow, Shared, PullDefault, 0x0000,
"\\_SB.GPO1", 0x00, ResourceConsumer, ,
)
{ // Pin list
0x0013
}
GpioIo (Shared, PullDefault, 0x0000, 0x0000,
IoRestrictionOutputOnly,
"\\_SB.GPO1", 0x00, ResourceConsumer, ,
)
{ // Pin list
0x0019
}
})
Return (RBUF) /* \_SB_.PCI0.I2C2.TCS1._CRS.RBUF */
}
There is no fixed order for these 2. This commit adds code to check that
there is 1 of each as expected and then registers a mapping matching their
order using devm_acpi_dev_add_driver_gpios().
This gives us access to both GPIOs allowing us to properly suspend the
controller during suspend, and making it possible to reset the controller
if necessary.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1786317
BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199207
Signed-off-by: Hans de Goede <[email protected]>
Reviewed-by: Bastien Nocera <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
GPIO setup
Before this commit we would always reset the controller at probe when we
have access to the GPIOs which are necessary to do a reset.
Doing the reset requires access to the GPIOs, but just because we have
access to the GPIOs does not mean that we should always reset the
controller at probe. On X86 ACPI platforms the BIOS / UEFI firmware will
already have reset the controller and it will have loaded the device
specific config into the controller. Doing the reset sometimes causes the
controller to lose its configuration, so on X86 ACPI platforms this is not
a good idea.
This commit adds a new reset_controller_at_probe boolean to control the
reset at probe behavior.
This commits sets the new bool to true when we set irq_pin_access_method
to IRQ_PIN_ACCESS_GPIO, so there are no functional changes.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1786317
BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199207
Reviewed-by: Bastien Nocera <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
setup
At least on X86 ACPI platforms it is not necessary to load the touchscreen
controller config from disk, if it needs to be loaded this has already been
done by the BIOS / UEFI firmware.
Even on other (e.g. devicetree) platforms the config-loading as currently
done has the issue that the loaded cfg file is based on the controller
model, but the actual cfg is device specific, so the cfg files are not
part of linux-firmware and this can only work with a device specific OS
image which includes the cfg file.
And we do not need access to the GPIOs at all to load the config, if we
do not have access we can still load the config.
So all in all tying the decision to try to load the config from disk to
being able to access the GPIOs is not desirable. This commit adds a new
load_cfg_from_disk boolean to control the firmware loading instead.
This commits sets the new bool to true when we set irq_pin_access_method
to IRQ_PIN_ACCESS_GPIO, so there are no functional changes.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1786317
BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199207
Reviewed-by: Bastien Nocera <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
Suspending Goodix touchscreens requires changing the interrupt pin to
output before sending them a power-down command. Followed by wiggling
the interrupt pin to wake the device up, after which it is put back
in input mode.
So far we have only effectively supported this on devices which use
devicetree. On X86 ACPI platforms both looking up the pins; and using a
pin as both IRQ and GPIO is a bit more complicated. E.g. on some devices
we cannot directly access the IRQ pin as GPIO and we need to call ACPI
methods to control it instead.
This commit adds a new irq_pin_access_method field to the goodix_chip_data
struct and adds goodix_irq_direction_output and goodix_irq_direction_input
helpers which together abstract the GPIO accesses to the IRQ pin.
This is a preparation patch for adding support for properly suspending the
touchscreen on X86 ACPI platforms.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1786317
BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199207
Signed-off-by: Hans de Goede <[email protected]>
Reviewed-by: Bastien Nocera <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
For non-fatal syndromes like LOCAL_LENGTH_ERR, recovery shouldn't be
triggered. In these scenarios, the RQ is not actually in ERR state.
This misleads the recovery flow which assumes that the RQ is really in
error state and no more completions arrive, causing crashes on bad page
state.
Fixes: 8276ea1353a4 ("net/mlx5e: Report and recover from CQE with error on RQ")
Signed-off-by: Aya Levin <[email protected]>
Reviewed-by: Tariq Toukan <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
In striding RQ mode, the buffers of an RX WQE are first
prepared and posted to the HW using a UMR WQEs via the ICOSQ.
We maintain the state of these in-progress WQEs in the RQ
SW struct.
In the flow of ICOSQ recovery, the corresponding RQ is not
in error state, hence:
- The buffers of the in-progress WQEs must be released
and the RQ metadata should reflect it.
- Existing RX WQEs in the RQ should not be affected.
For this, wrap the dealloc of the in-progress WQEs in
a function, and use it in the ICOSQ recovery flow
instead of mlx5e_free_rx_descs().
Fixes: be5323c8379f ("net/mlx5e: Report and recover from CQE error on ICOSQ")
Signed-off-by: Aya Levin <[email protected]>
Reviewed-by: Tariq Toukan <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
When resetting the RQ (moving RQ state from RST to RDY), the driver
resets the WQ's SW metadata.
In striding RQ mode, we maintain a field that reflects the actual
expected WQ head (including in progress WQEs posted to the ICOSQ).
It was mistakenly not reset together with the WQ. Fix this here.
Fixes: 8276ea1353a4 ("net/mlx5e: Report and recover from CQE with error on RQ")
Signed-off-by: Aya Levin <[email protected]>
Reviewed-by: Tariq Toukan <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
Add number of WQEBBs (WQE's Basic Block) to WQE info struct. Set the
number of WQEBBs on WQE post, and increment the consumer counter (cc)
on completion.
In case of error completions, the cc was mistakenly not incremented,
keeping a gap between cc and pc (producer counter). This failed the
recovery flow on the ICOSQ from a CQE error which timed-out waiting for
the cc and pc to meet.
Fixes: be5323c8379f ("net/mlx5e: Report and recover from CQE error on ICOSQ")
Signed-off-by: Aya Levin <[email protected]>
Reviewed-by: Tariq Toukan <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
The cap_mask1 isn't protected by field_select and not listed among RW
fields, but it is required to be written to properly initialize ports
in IB virtualization mode.
Link: https://lore.kernel.org/linux-rdma/[email protected]
Fixes: ab118da4c10a ("net/mlx5: Don't write read-only fields in MODIFY_HCA_VPORT_CONTEXT command")
Signed-off-by: Leon Romanovsky <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
Nvidia card may come with a "phantom" UCSI device, and its driver gets
stuck in probe routine, prevents any system PM operations like suspend.
There's an unaccounted case that the target time can equal to jiffies in
gpu_i2c_check_status(), let's solve that by using readl_poll_timeout()
instead of jiffies comparison functions.
Fixes: c71bcdcb42a7 ("i2c: add i2c bus driver for NVIDIA GPU")
Suggested-by: Andy Shevchenko <[email protected]>
Signed-off-by: Kai-Heng Feng <[email protected]>
Reviewed-by: Andy Shevchenko <[email protected]>
Reviewed-by: Ajay Gupta <[email protected]>
Tested-by: Ajay Gupta <[email protected]>
Signed-off-by: Wolfram Sang <[email protected]>
|
|
Add a test case to check nf queue infrastructure.
Could be extended in the future to also cover serialization of
conntrack, uid and secctx attributes in nfqueue.
For now, this checks that 'queue bypass' works, that a queue rule with
no bypass option blocks traffic and that userspace receives the expected
number of packets.
For this we add two queues and hook all of
prerouting/input/forward/output/postrouting.
Packets get queued twice with a dummy base chain in between:
This passes with current nf tree, but reverting
commit 946c0d8e6ed4 ("netfilter: nf_queue: fix reinject verdict handling")
makes this trip (it processes 30 instead of expected 20 packets).
v2: update config file with queue and other options missing/needed for
other tests.
v3: also test with tcp, this reveals problem with commit
28f8bfd1ac94 ("netfilter: Support iif matches in POSTROUTING"), due to
skb->dev pointing at another skb in the retransmit rbtree (skb->dev
aliases to rbnode child).
Signed-off-by: Florian Westphal <[email protected]>
Signed-off-by: Pablo Neira Ayuso <[email protected]>
|
|
Set skb->tc_redirected to 1, otherwise the ifb driver drops the packet.
Set skb->tc_from_ingress to 1 to reinject the packet back to the ingress
path after leaving the ifb egress path.
This patch inconditionally sets on these two skb fields that are
meaningful to the ifb driver. The existing forward action is guaranteed
to run from ingress path.
Fixes: 39e6dea28adc ("netfilter: nf_tables: add forward expression to the netdev family")
Signed-off-by: Pablo Neira Ayuso <[email protected]>
|
|
Make sure the forward action is only used from ingress.
Fixes: 39e6dea28adc ("netfilter: nf_tables: add forward expression to the netdev family")
Signed-off-by: Pablo Neira Ayuso <[email protected]>
|
|
...and return -ENOTEMPTY to the front-end in this case, instead of
proceeding. Currently, nft takes care of checking for these cases
and not sending them to the kernel, but if we drop the set_overlap()
call in nft we can end up in situations like:
# nft add table t
# nft add set t s '{ type inet_service ; flags interval ; }'
# nft add element t s '{ 1 - 5 }'
# nft add element t s '{ 6 - 10 }'
# nft add element t s '{ 4 - 7 }'
# nft list set t s
table ip t {
set s {
type inet_service
flags interval
elements = { 1-3, 4-5, 6-7 }
}
}
This change has the primary purpose of making the behaviour
consistent with nft_set_pipapo, but is also functional to avoid
inconsistent behaviour if userspace sends overlapping elements for
any reason.
v2: When we meet the same key data in the tree, as start element while
inserting an end element, or as end element while inserting a start
element, actually check that the existing element is active, before
resetting the overlap flag (Pablo Neira Ayuso)
Signed-off-by: Stefano Brivio <[email protected]>
Signed-off-by: Pablo Neira Ayuso <[email protected]>
|
|
Replace negations of nft_rbtree_interval_end() with a new helper,
nft_rbtree_interval_start(), wherever this helps to visualise the
problem at hand, that is, for all the occurrences except for the
comparison against given flags in __nft_rbtree_get().
This gets especially useful in the next patch.
Signed-off-by: Stefano Brivio <[email protected]>
Signed-off-by: Pablo Neira Ayuso <[email protected]>
|
|
insertion
...and return -ENOTEMPTY to the front-end on collision, -EEXIST if
an identical element already exists. Together with the previous patch,
element collision will now be returned to the user as -EEXIST.
Reported-by: Phil Sutter <[email protected]>
Signed-off-by: Stefano Brivio <[email protected]>
Signed-off-by: Pablo Neira Ayuso <[email protected]>
|
|
insertion
Currently, the -EEXIST return code of ->insert() callbacks is ambiguous: it
might indicate that a given element (including intervals) already exists as
such, or that the new element would clash with existing ones.
If identical elements already exist, the front-end is ignoring this without
returning error, in case NLM_F_EXCL is not set. However, if the new element
can't be inserted due an overlap, we should report this to the user.
To this purpose, allow set back-ends to return -ENOTEMPTY on collision with
existing elements, translate that to -EEXIST, and return that to userspace,
no matter if NLM_F_EXCL was set.
Reported-by: Phil Sutter <[email protected]>
Signed-off-by: Stefano Brivio <[email protected]>
Signed-off-by: Pablo Neira Ayuso <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf tooling fixes from Ingo Molnar:
"A handful of tooling fixes all across the map, no kernel changes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tools headers uapi: Update linux/in.h copy
perf probe: Do not depend on dwfl_module_addrsym()
perf probe: Fix to delete multiple probe event
perf parse-events: Fix reading of invalid memory in event parsing
perf python: Fix clang detection when using CC=clang-version
perf map: Fix off by one in strncpy() size argument
tools: Let O= makes handle a relative path with -C option
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fix from Ingo Molnar:
"A build fix with certain Kconfig combinations"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/ioremap: Fix CONFIG_EFI=n build
|
|
Pull dmaengine fixes from Vinod Koul:
"Late fixes in dmaengine for v5.6:
- move .device_release missing log warning to debug
- couple of maintainer entries for HiSilicon and IADX drivers
- off-by-one fix for idxd driver
- documentation warning fixes
- TI k3 dma error handling fix"
* tag 'dmaengine-fix-5.6' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: ti: k3-udma-glue: Fix an error handling path in 'k3_udma_glue_cfg_rx_flow()'
MAINTAINERS: Add maintainer for HiSilicon DMA engine driver
dmaengine: idxd: fix off by one on cdev dwq refcount
MAINTAINERS: rectify the INTEL IADX DRIVER entry
dmaengine: move .device_release missing log warning to debug level
docs: dmaengine: provider.rst: get rid of some warnings
|
|
The timer is disarmed when switching between TSC deadline and other modes,
we should set everything to disarmed state, however, LAPIC timer can be
emulated by preemption timer, it still works if vmx->hv_deadline_timer is
not -1. This patch also cancels preemption timer when disarm LAPIC timer.
Signed-off-by: Wanpeng Li <[email protected]>
Message-Id: <[email protected]>
Signed-off-by: Paolo Bonzini <[email protected]>
|
|
There are at least 3 models of the HP x2 10 models:
Bay Trail SoC + AXP288 PMIC
Cherry Trail SoC + AXP288 PMIC
Cherry Trail SoC + TI PMIC
Like on the other HP x2 10 models we need to ignore wakeup for ACPI GPIO
events on the external embedded-controller pin to avoid spurious wakeups
on the HP x2 10 CHT + AXP288 model too.
This commit adds an extra DMI based quirk for the HP x2 10 CHT + AXP288
model, ignoring wakeups for ACPI GPIO events on the EC interrupt pin
on this model. This fixes spurious wakeups from suspend on this model.
Fixes: aa23ca3d98f7 ("gpiolib: acpi: Add honor_wakeup module-option + quirk mechanism")
Reported-and-tested-by: Marc Lehmann <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Acked-by: Mika Westerberg <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
After xfrm_add_policy add a policy, its ref is 2, then
xfrm_policy_timer
read_lock
xp->walk.dead is 0
....
mod_timer()
xfrm_policy_kill
policy->walk.dead = 1
....
del_timer(&policy->timer)
xfrm_pol_put //ref is 1
xfrm_pol_put //ref is 0
xfrm_policy_destroy
call_rcu
xfrm_pol_hold //ref is 1
read_unlock
xfrm_pol_put //ref is 0
xfrm_policy_destroy
call_rcu
xfrm_policy_destroy is called twice, which may leads to
double free.
Call Trace:
RIP: 0010:refcount_warn_saturate+0x161/0x210
...
xfrm_policy_timer+0x522/0x600
call_timer_fn+0x1b3/0x5e0
? __xfrm_decode_session+0x2990/0x2990
? msleep+0xb0/0xb0
? _raw_spin_unlock_irq+0x24/0x40
? __xfrm_decode_session+0x2990/0x2990
? __xfrm_decode_session+0x2990/0x2990
run_timer_softirq+0x5c5/0x10e0
Fix this by use write_lock_bh in xfrm_policy_kill.
Fixes: ea2dea9dacc2 ("xfrm: remove policy lock when accessing policy->walk.dead")
Signed-off-by: YueHaibing <[email protected]>
Acked-by: Timo Teräs <[email protected]>
Acked-by: Herbert Xu <[email protected]>
Signed-off-by: Steffen Klassert <[email protected]>
|
|
Add missing Makefile for net/forwarding tests and include it to
the targets list, otherwise forwarding tests are not installed
in case of cross-compilation.
Signed-off-by: Vadym Kochan <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Andrew noticed that some handlers for *_SET commands leak a netdev
reference if required ethtool_ops callbacks do not exist. A simple
reproducer would be e.g.
ip link add veth1 type veth peer name veth2
ethtool -s veth1 wol g
ip link del veth1
Make sure dev_put() is called when ethtool_ops check fails.
v2: add Fixes tags
Fixes: a53f3d41e4d3 ("ethtool: set link settings with LINKINFO_SET request")
Fixes: bfbcfe2032e7 ("ethtool: set link modes related data with LINKMODES_SET request")
Fixes: e54d04e3afea ("ethtool: set message mask with DEBUG_SET request")
Fixes: 8d425b19b305 ("ethtool: set wake-on-lan settings with WOL_SET request")
Reported-by: Andrew Lunn <[email protected]>
Signed-off-by: Michal Kubecek <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Reviewed-by: Jakub Kicinski <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
When both the switch and the bridge are learning about new addresses,
switch ports attached to the bridge would see duplicate ARP frames
because both entities would attempt to send them.
Fixes: 5037d532b83d ("net: dsa: add Broadcom tag RX/TX handler")
Reported-by: Maxime Bizon <[email protected]>
Signed-off-by: Florian Fainelli <[email protected]>
Reviewed-by: Vivien Didelot <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Michael Chan says:
====================
bnxt_en: Bug fixes.
5 bug fix patches covering an indexing bug for priority counters, memory
leak when retrieving DCB ETS settings, error path return code, proper
disabling of PCI before freeing context memory, and proper ring accounting
in error path.
Please also apply these to -stable. Thanks.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
If ring counts are not reset when ring reservation fails,
bnxt_init_dflt_ring_mode() will not be called again to reinitialise
IRQs when open() is called and results in system crash as napi will
also be not initialised. This patch fixes it by resetting the ring
counts.
Fixes: 47558acd56a7 ("bnxt_en: Reserve rings at driver open if none was reserved at probe time.")
Signed-off-by: Vasundhara Volam <[email protected]>
Signed-off-by: Michael Chan <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Other shutdown code paths will always disable PCI first to shutdown DMA
before freeing context memory. Do the same sequence in the error path
of probe to be safe and consistent.
Fixes: c20dc142dd7b ("bnxt_en: Disable bus master during PCI shutdown and driver unload.")
Signed-off-by: Michael Chan <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The current code ignores the return value from
bnxt_hwrm_func_backing_store_cfg(), causing the driver to proceed in
the init path even when this vital firmware call has failed. Fix it
by propagating the error code to the caller.
Fixes: 1b9394e5a2ad ("bnxt_en: Configure context memory on new devices.")
Signed-off-by: Michael Chan <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The allocated ieee_ets structure goes out of scope without being freed,
leaking memory. Appropriate result codes should be returned so that
callers do not rely on invalid data passed by reference.
Also cache the ETS config retrieved from the device so that it doesn't
need to be freed. The balance of the code was clearly written with the
intent of having the results of querying the hardware cached in the
device structure. The commensurate store was evidently missed though.
Fixes: 7df4ae9fe855 ("bnxt_en: Implement DCBNL to support host-based DCBX.")
Signed-off-by: Edwin Peer <[email protected]>
Signed-off-by: Michael Chan <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
There is an indexing bug in determining these ethtool priority
counters. Instead of using the queue ID to index, we need to
normalize by modulo 10 to get the index. This index is then used
to obtain the proper CoS queue counter. Rename bp->pri2cos to
bp->pri2cos_idx to make this more clear.
Fixes: e37fed790335 ("bnxt_en: Add ethtool -S priority counters.")
Signed-off-by: Michael Chan <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Only attach macsec to ethernet devices.
Syzbot was able to trigger a KMSAN warning in macsec_handle_frame
by attaching to a phonet device.
Macvlan has a similar check in macvlan_port_create.
v1->v2
- fix commit message typo
Reported-by: syzbot <[email protected]>
Signed-off-by: Willem de Bruijn <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Unlike NL_SET_ERR_* macros, nl_set_extack_cookie_u64() and
nl_set_extack_cookie_u32() helpers do not check extack argument for null
and neither do their callers, as syzbot recently discovered for
ethnl_parse_header().
Instead of fixing the callers and leaving the trap in place, add check of
null extack to both helpers to make them consistent with NL_SET_ERR_*
macros.
v2: drop incorrect second Fixes tag
Fixes: 2363d73a2f3e ("ethtool: reject unrecognized request flags")
Reported-by: [email protected]
Signed-off-by: Michal Kubecek <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
ASKEY WWHC050 is a mcie LTE modem.
The oem configuration states:
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1690 ProdID=7588 Rev=ff.ff
S: Manufacturer=Android
S: Product=Android
S: SerialNumber=813f0eef6e6e
C:* #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=88(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none)
E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=125us
Tested on openwrt distribution.
Signed-off-by: Cezary Jackiewicz <[email protected]>
Signed-off-by: Pawel Dembicki <[email protected]>
Acked-by: Bjørn Mork <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The nci_conn_max_data_pkt_payload_size() function sometimes returns
-EPROTO so "max_size" needs to be signed for the error handling to
work. We can make "payload_size" an int as well.
Fixes: a06347c04c13 ("NFC: Add Intel Fields Peak NFC solution driver")
Signed-off-by: Dan Carpenter <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
There is a place,
inet_dump_fib()
fib_table_dump
fn_trie_dump_leaf()
hlist_for_each_entry_rcu()
without rcu_read_lock() will trigger a warning,
WARNING: suspicious RCU usage
-----------------------------
net/ipv4/fib_trie.c:2216 RCU-list traversed in non-reader section!!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
1 lock held by ip/1923:
#0: ffffffff8ce76e40 (rtnl_mutex){+.+.}, at: netlink_dump+0xd6/0x840
Call Trace:
dump_stack+0xa1/0xea
lockdep_rcu_suspicious+0x103/0x10d
fn_trie_dump_leaf+0x581/0x590
fib_table_dump+0x15f/0x220
inet_dump_fib+0x4ad/0x5d0
netlink_dump+0x350/0x840
__netlink_dump_start+0x315/0x3e0
rtnetlink_rcv_msg+0x4d1/0x720
netlink_rcv_skb+0xf0/0x220
rtnetlink_rcv+0x15/0x20
netlink_unicast+0x306/0x460
netlink_sendmsg+0x44b/0x770
__sys_sendto+0x259/0x270
__x64_sys_sendto+0x80/0xa0
do_syscall_64+0x69/0xf4
entry_SYSCALL_64_after_hwframe+0x49/0xb3
Fixes: 18a8021a7be3 ("net/ipv4: Plumb support for filtering route dumps")
Signed-off-by: Qian Cai <[email protected]>
Reviewed-by: David Ahern <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2020-03-05
This series introduces some fixes to mlx5 driver.
Please pull and let me know if there is any problem.
For -stable v5.4
('net/mlx5: DR, Fix postsend actions write length')
For -stable v5.5
('net/mlx5e: kTLS, Fix TCP seq off-by-1 issue in TX resync flow')
('net/mlx5e: Fix endianness handling in pedit mask')
====================
Reviewed-by: Jakub Kicinski <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The following warning can occur when a pq is left on the dmawait list and
the pq is then freed:
WARNING: CPU: 47 PID: 3546 at lib/list_debug.c:29 __list_add+0x65/0xc0
list_add corruption. next->prev should be prev (ffff939228da1880), but was ffff939cabb52230. (next=ffff939cabb52230).
Modules linked in: mmfs26(OE) mmfslinux(OE) tracedev(OE) 8021q garp mrp ib_isert iscsi_target_mod target_core_mod crc_t10dif crct10dif_generic opa_vnic rpcrdma ib_iser libiscsi scsi_transport_iscsi ib_ipoib(OE) bridge stp llc iTCO_wdt iTCO_vendor_support intel_powerclamp coretemp intel_rapl iosf_mbi kvm_intel kvm irqbypass crct10dif_pclmul crct10dif_common crc32_pclmul ghash_clmulni_intel aesni_intel lrw gf128mul glue_helper ablk_helper cryptd ast ttm drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops drm pcspkr joydev drm_panel_orientation_quirks i2c_i801 mei_me lpc_ich mei wmi ipmi_si ipmi_devintf ipmi_msghandler nfit libnvdimm acpi_power_meter acpi_pad hfi1(OE) rdmavt(OE) rdma_ucm ib_ucm ib_uverbs ib_umad rdma_cm ib_cm iw_cm ib_core binfmt_misc numatools(OE) xpmem(OE) ip_tables
nfsv3 nfs_acl nfs lockd grace sunrpc fscache igb ahci libahci i2c_algo_bit dca libata ptp pps_core crc32c_intel [last unloaded: i2c_algo_bit]
CPU: 47 PID: 3546 Comm: wrf.exe Kdump: loaded Tainted: G W OE ------------ 3.10.0-957.41.1.el7.x86_64 #1
Hardware name: HPE.COM HPE SGI 8600-XA730i Gen10/X11DPT-SB-SG007, BIOS SBED1229 01/22/2019
Call Trace:
[<ffffffff91f65ac0>] dump_stack+0x19/0x1b
[<ffffffff91898b78>] __warn+0xd8/0x100
[<ffffffff91898bff>] warn_slowpath_fmt+0x5f/0x80
[<ffffffff91a1dabe>] ? ___slab_alloc+0x24e/0x4f0
[<ffffffff91b97025>] __list_add+0x65/0xc0
[<ffffffffc03926a5>] defer_packet_queue+0x145/0x1a0 [hfi1]
[<ffffffffc0372987>] sdma_check_progress+0x67/0xa0 [hfi1]
[<ffffffffc03779d2>] sdma_send_txlist+0x432/0x550 [hfi1]
[<ffffffff91a20009>] ? kmem_cache_alloc+0x179/0x1f0
[<ffffffffc0392973>] ? user_sdma_send_pkts+0xc3/0x1990 [hfi1]
[<ffffffffc0393e3a>] user_sdma_send_pkts+0x158a/0x1990 [hfi1]
[<ffffffff918ab65e>] ? try_to_del_timer_sync+0x5e/0x90
[<ffffffff91a3fe1a>] ? __check_object_size+0x1ca/0x250
[<ffffffffc0395546>] hfi1_user_sdma_process_request+0xd66/0x1280 [hfi1]
[<ffffffffc034e0da>] hfi1_aio_write+0xca/0x120 [hfi1]
[<ffffffff91a4245b>] do_sync_readv_writev+0x7b/0xd0
[<ffffffff91a4409e>] do_readv_writev+0xce/0x260
[<ffffffff918df69f>] ? pick_next_task_fair+0x5f/0x1b0
[<ffffffff918db535>] ? sched_clock_cpu+0x85/0xc0
[<ffffffff91f6b16a>] ? __schedule+0x13a/0x860
[<ffffffff91a442c5>] vfs_writev+0x35/0x60
[<ffffffff91a4447f>] SyS_writev+0x7f/0x110
[<ffffffff91f78ddb>] system_call_fastpath+0x22/0x27
The issue happens when wait_event_interruptible_timeout() returns a value
<= 0.
In that case, the pq is left on the list. The code continues sending
packets and potentially can complete the current request with the pq still
on the dmawait list provided no descriptor shortage is seen.
If the pq is torn down in that state, the sdma interrupt handler could
find the now freed pq on the list with list corruption or memory
corruption resulting.
Fix by adding a flush routine to ensure that the pq is never on a list
after processing a request.
A follow-up patch series will address issues with seqlock surfaced in:
https://lore.kernel.org/r/[email protected]
The seqlock use for sdma will then be converted to a spin lock since the
list_empty() doesn't need the protection afforded by the sequence lock
currently in use.
Fixes: a0d406934a46 ("staging/rdma/hfi1: Add page lock limit check for SDMA requests")
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Kaike Wan <[email protected]>
Signed-off-by: Mike Marciniszyn <[email protected]>
Signed-off-by: Dennis Dalessandro <[email protected]>
Signed-off-by: Jason Gunthorpe <[email protected]>
|