aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2018-12-04mmc: core: use mrq->sbc when sending CMD23 for RPMBWolfram Sang1-5/+10
When sending out CMD23 in the blk preparation, the comment there rightfully says: * However, it is not sufficient to just send CMD23, * and avoid the final CMD12, as on an error condition * CMD12 (stop) needs to be sent anyway. This, coupled * with Auto-CMD23 enhancements provided by some * hosts, means that the complexity of dealing * with this is best left to the host. If CMD23 is * supported by card and host, we'll fill sbc in and let * the host deal with handling it correctly. Let's do this behaviour for RPMB as well, and not send CMD23 independently. Otherwise IP cores (like Renesas SDHI) may timeout because of automatic CMD23/CMD12 handling. Reported-by: Masaharu Hayakawa <[email protected]> Signed-off-by: Wolfram Sang <[email protected]> Tested-by: Clément Péron <[email protected]> Reviewed-by: Avri Altman <[email protected]> Reviewed-by: Niklas Söderlund <[email protected]> Cc: [email protected] Signed-off-by: Ulf Hansson <[email protected]>
2018-12-04kprobes/x86: Fix instruction patching corruption when copying more than one ↵Masami Hiramatsu1-1/+1
RIP-relative instruction After copy_optimized_instructions() copies several instructions to the working buffer it tries to fix up the real RIP address, but it adjusts the RIP-relative instruction with an incorrect RIP address for the 2nd and subsequent instructions due to a bug in the logic. This will break the kernel pretty badly (with likely outcomes such as a kernel freeze, a crash, or worse) because probed instructions can refer to the wrong data. For example putting kprobes on cpumask_next() typically hits this bug. cpumask_next() is normally like below if CONFIG_CPUMASK_OFFSTACK=y (in this case nr_cpumask_bits is an alias of nr_cpu_ids): <cpumask_next>: 48 89 f0 mov %rsi,%rax 8b 35 7b fb e2 00 mov 0xe2fb7b(%rip),%esi # ffffffff82db9e64 <nr_cpu_ids> 55 push %rbp ... If we put a kprobe on it and it gets jump-optimized, it gets patched by the kprobes code like this: <cpumask_next>: e9 95 7d 07 1e jmpq 0xffffffffa000207a 7b fb jnp 0xffffffff81f8a2e2 <cpumask_next+2> e2 00 loop 0xffffffff81f8a2e9 <cpumask_next+9> 55 push %rbp This shows that the first two MOV instructions were copied to a trampoline buffer at 0xffffffffa000207a. Here is the disassembled result of the trampoline, skipping the optprobe template instructions: # Dump of assembly code from 0xffffffffa000207a to 0xffffffffa00020ea: 54 push %rsp ... 48 83 c4 08 add $0x8,%rsp 9d popfq 48 89 f0 mov %rsi,%rax 8b 35 82 7d db e2 mov -0x1d24827e(%rip),%esi # 0xffffffff82db9e67 <nr_cpu_ids+3> This dump shows that the second MOV accesses *(nr_cpu_ids+3) instead of the original *nr_cpu_ids. This leads to a kernel freeze because cpumask_next() always returns 0 and for_each_cpu() never ends. Fix this by adding 'len' correctly to the real RIP address while copying. [ mingo: Improved the changelog. ] Reported-by: Michael Rodin <[email protected]> Signed-off-by: Masami Hiramatsu <[email protected]> Reviewed-by: Steven Rostedt (VMware) <[email protected]> Cc: Arnaldo Carvalho de Melo <[email protected]> Cc: Linus Torvalds <[email protected]> Cc: Peter Zijlstra <[email protected]> Cc: Ravi Bangoria <[email protected]> Cc: Steven Rostedt <[email protected]> Cc: Thomas Gleixner <[email protected]> Cc: [email protected] # v4.15+ Fixes: 63fef14fc98a ("kprobes/x86: Make insn buffer always ROX and use text_poke()") Link: http://lkml.kernel.org/r/153504457253.22602.1314289671019919596.stgit@devbox Signed-off-by: Ingo Molnar <[email protected]>
2018-12-03Merge branch 'mlx4-fixes'David S. Miller3-4/+3
Tariq Toukan says: ==================== mlx4 fixes for 4.20-rc This patchset includes small fixes for the mlx4_en driver. First patch by Eran fixes the value used to init the netdevice's min_mtu field. Please queue it to -stable >= v4.10. Second patch by Saeed adds missing Kconfig build dependencies. Series generated against net commit: 35b827b6d061 tun: forbid iface creation with rtnl ops ==================== Signed-off-by: David S. Miller <[email protected]>
2018-12-03net/mlx4_en: Fix build break when CONFIG_INET is offSaeed Mahameed1-1/+1
MLX4_EN depends on NETDEVICES, ETHERNET and INET Kconfigs. Make sure they are listed in MLX4_EN Kconfig dependencies. This fixes the following build break: drivers/net/ethernet/mellanox/mlx4/en_rx.c:582:18: warning: ‘struct iphdr’ declared inside parameter list [enabled by default] struct iphdr *iph) ^ drivers/net/ethernet/mellanox/mlx4/en_rx.c:582:18: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default] drivers/net/ethernet/mellanox/mlx4/en_rx.c: In function ‘get_fixed_ipv4_csum’: drivers/net/ethernet/mellanox/mlx4/en_rx.c:586:20: error: dereferencing pointer to incomplete type _u8 ipproto = iph->protocol; Signed-off-by: Saeed Mahameed <[email protected]> Signed-off-by: Tariq Toukan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2018-12-03net/mlx4_en: Change min MTU size to ETH_MIN_MTUEran Ben Elisha2-3/+2
NIC driver minimal MTU size shall be set to ETH_MIN_MTU, as defined in the RFC791 and in the network stack. Remove old mlx4_en only define for it, which was set to wrong value. Fixes: b80f71f5816f ("ethernet/mellanox: use core min/max MTU checking") Signed-off-by: Eran Ben Elisha <[email protected]> Signed-off-by: Tariq Toukan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2018-12-03net/core: tidy up an error messageQian Cai1-2/+2
netif_napi_add() could report an error like this below due to it allows to pass a format string for wildcarding before calling dev_get_valid_name(), "netif_napi_add() called with weight 256 on device eth%d" For example, hns_enet_drv module does this. hns_nic_try_get_ae hns_nic_init_ring_data netif_napi_add register_netdev dev_get_valid_name Hence, make it a bit more human-readable by using netdev_err_once() instead. Signed-off-by: Qian Cai <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2018-12-03Revert "PCI/ASPM: Do not initialize link state when aspm_disabled is set"Bjorn Helgaas1-1/+1
This reverts commit 17c91487364fb33797ed84022564ee7544ac4945. Rafael found that this commit broke the SD card reader in his Acer Aspire S5. Details of the problem are in the bugzilla below. Fixes: 17c91487364f ("PCI/ASPM: Do not initialize link state when aspm_disabled is set") Link: https://bugzilla.kernel.org/show_bug.cgi?id=201801 Signed-off-by: Bjorn Helgaas <[email protected]>
2018-12-03mv88e6060: disable hardware level MAC learningAnderson Luiz Alves1-7/+3
Disable hardware level MAC learning because it breaks station roaming. When enabled it drops all frames that arrive from a MAC address that is on a different port at learning table. Signed-off-by: Anderson Luiz Alves <[email protected]> Reviewed-by: Andrew Lunn <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2018-12-03macvlan: return correct error valueMatteo Croce1-2/+5
A MAC address must be unique among all the macvlan devices with the same lower device. The only exception is the passthru [sic] mode, which shares the lower device address. When duplicate addresses are detected, EBUSY is returned when bringing the interface up: # ip link add macvlan0 link eth0 type macvlan # read addr </sys/class/net/eth0/address # ip link set macvlan0 address $addr # ip link set macvlan0 up RTNETLINK answers: Device or resource busy Use correct error code which is EADDRINUSE, and do the check also earlier, on address change: # ip link set macvlan0 address $addr RTNETLINK answers: Address already in use Signed-off-by: Matteo Croce <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2018-12-03sctp: kfree_rcu asocXin Long2-1/+3
In sctp_hash_transport/sctp_epaddr_lookup_transport, it dereferences a transport's asoc under rcu_read_lock while asoc is freed not after a grace period, which leads to a use-after-free panic. This patch fixes it by calling kfree_rcu to make asoc be freed after a grace period. Note that only the asoc's memory is delayed to free in the patch, it won't cause sk to linger longer. Thanks Neil and Marcelo to make this clear. Fixes: 7fda702f9315 ("sctp: use new rhlist interface on sctp transport rhashtable") Fixes: cd2b70875058 ("sctp: check duplicate node before inserting a new transport") Reported-by: [email protected] Reported-by: [email protected] Suggested-by: Neil Horman <[email protected]> Signed-off-by: Xin Long <[email protected]> Acked-by: Marcelo Ricardo Leitner <[email protected]> Acked-by: Neil Horman <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2018-12-03net/ibmvnic: Fix RTNL deadlock during device resetThomas Falcon1-1/+1
Commit a5681e20b541 ("net/ibmnvic: Fix deadlock problem in reset") made the change to hold the RTNL lock during driver reset but still calls netdev_notify_peers, which results in a deadlock. Instead, use call_netdevice_notifiers, which is functionally the same except that it does not take the RTNL lock again. Fixes: a5681e20b541 ("net/ibmnvic: Fix deadlock problem in reset") Signed-off-by: Thomas Falcon <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2018-12-03vhost: fix IOTLB lockingJean-Philippe Brucker1-3/+0
Commit 78139c94dc8c ("net: vhost: lock the vqs one by one") moved the vq lock to improve scalability, but introduced a possible deadlock in vhost-iotlb. vhost_iotlb_notify_vq() now takes vq->mutex while holding the device's IOTLB spinlock. And on the vhost_iotlb_miss() path, the spinlock is taken while holding vq->mutex. Since calling vhost_poll_queue() doesn't require any lock, avoid the deadlock by not taking vq->mutex. Fixes: 78139c94dc8c ("net: vhost: lock the vqs one by one") Acked-by: Jason Wang <[email protected]> Acked-by: Michael S. Tsirkin <[email protected]> Signed-off-by: Jean-Philippe Brucker <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2018-12-03Merge branch 'phy-micrel-toggling-reset'David S. Miller2-5/+14
Yoshihiro Shimoda says: ==================== net: phy: micrel: add toggling phy reset This patch set is for R-Car Gen3 Salvator-XS boards. If we do the following method, the phy cannot link up correctly. 1) Kernel boots by using initramfs. --> No open the nic, so phy_device_register() and phy_probe() deasserts the reset. 2) Kernel enters the suspend. --> So, keep the reset signal as deassert. --> On R-Car Salvator-XS board, unfortunately, the board power is turned off. 3) Kernel returns from suspend. 4) ifconfig eth0 up --> Then, since edge signal of the reset doesn't happen, it cannot link up. 5) ifconfig eth0 down 6) ifconfig eth0 up --> In this case, it can link up. When resolving this issue after I got feedback from Andrew and Heiner, I found an issue that the phy_device.c didn't call phy_resume() if the PHY was not attached. So, patch 1 fixes it and add toggling the phy reset to the micrel phy driver. Changes from v1 (as RFC): - No remove the current code of phy_device.c to avoid any side effects. - Fix the mdio_bus_phy_resume() in phy_device.c. - Add toggling the phy reset in micrel.c if the PHY is not attached. ==================== Signed-off-by: David S. Miller <[email protected]>
2018-12-03net: phy: micrel: add toggling phy reset if PHY is not attachedYoshihiro Shimoda1-0/+8
This patch adds toggling phy reset if PHY is not attached. Otherwise, some boards (e.g. R-Car H3 Salvator-XS) cannot link up correctly if we do the following method: 1) Kernel boots by using initramfs. --> No open the nic, so phy_device_register() and phy_probe() deasserts the reset. 2) Kernel enters the suspend. --> So, keep the reset signal as deassert. --> On R-Car Salvator-XS board, unfortunately, the board power is turned off. 3) Kernel returns from suspend. 4) ifconfig eth0 up --> Then, since edge signal of the reset doesn't happen, it cannot link up. 5) ifconfig eth0 down 6) ifconfig eth0 up --> In this case, it can link up. Reported-by: Hiromitsu Yamasaki <[email protected]> Signed-off-by: Yoshihiro Shimoda <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2018-12-03net: phy: Fix not to call phy_resume() if PHY is not attachedYoshihiro Shimoda1-5/+6
This patch fixes an issue that mdio_bus_phy_resume() doesn't call phy_resume() if the PHY is not attached. Fixes: 803dd9c77ac3 ("net: phy: avoid suspending twice a PHY") Signed-off-by: Yoshihiro Shimoda <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2018-12-03bpf: powerpc64: optimize JIT passes for bpf function callsSandipan Das1-0/+66
Once the JITed images for each function in a multi-function program are generated after the first three JIT passes, we only need to fix the target address for the branch instruction corresponding to each bpf-to-bpf function call. This introduces the following optimizations for reducing the work done by the JIT compiler when handling multi-function programs: [1] Instead of doing two extra passes to fix the bpf function calls, do just one as that would be sufficient. [2] During the extra pass, only overwrite the instruction sequences for the bpf-to-bpf function calls as everything else would still remain exactly the same. This also reduces the number of writes to the JITed image. [3] Do not regenerate the prologue and the epilogue during the extra pass as that would be redundant. Signed-off-by: Sandipan Das <[email protected]> Signed-off-by: Daniel Borkmann <[email protected]>
2018-12-03tun: remove skb access after netif_receive_skbPrashant Bhole1-1/+2
In tun.c skb->len was accessed while doing stats accounting after a call to netif_receive_skb. We can not access skb after this call because buffers may be dropped. The fix for this bug would be to store skb->len in local variable and then use it after netif_receive_skb(). IMO using xdp data size for accounting bytes will be better because input for tun_xdp_one() is xdp_buff. Hence this patch: - fixes a bug by removing skb access after netif_receive_skb() - uses xdp data size for accounting bytes [613.019057] BUG: KASAN: use-after-free in tun_sendmsg+0x77c/0xc50 [tun] [613.021062] Read of size 4 at addr ffff8881da9ab7c0 by task vhost-1115/1155 [613.023073] [613.024003] CPU: 0 PID: 1155 Comm: vhost-1115 Not tainted 4.20.0-rc3-vm+ #232 [613.026029] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014 [613.029116] Call Trace: [613.031145] dump_stack+0x5b/0x90 [613.032219] print_address_description+0x6c/0x23c [613.034156] ? tun_sendmsg+0x77c/0xc50 [tun] [613.036141] kasan_report.cold.5+0x241/0x308 [613.038125] tun_sendmsg+0x77c/0xc50 [tun] [613.040109] ? tun_get_user+0x1960/0x1960 [tun] [613.042094] ? __isolate_free_page+0x270/0x270 [613.045173] vhost_tx_batch.isra.14+0xeb/0x1f0 [vhost_net] [613.047127] ? peek_head_len.part.13+0x90/0x90 [vhost_net] [613.049096] ? get_tx_bufs+0x5a/0x2c0 [vhost_net] [613.051106] ? vhost_enable_notify+0x2d8/0x420 [vhost] [613.053139] handle_tx_copy+0x2d0/0x8f0 [vhost_net] [613.053139] ? vhost_net_buf_peek+0x340/0x340 [vhost_net] [613.053139] ? __mutex_lock+0x8d9/0xb30 [613.053139] ? finish_task_switch+0x8f/0x3f0 [613.053139] ? handle_tx+0x32/0x120 [vhost_net] [613.053139] ? mutex_trylock+0x110/0x110 [613.053139] ? finish_task_switch+0xcf/0x3f0 [613.053139] ? finish_task_switch+0x240/0x3f0 [613.053139] ? __switch_to_asm+0x34/0x70 [613.053139] ? __switch_to_asm+0x40/0x70 [613.053139] ? __schedule+0x506/0xf10 [613.053139] handle_tx+0xc7/0x120 [vhost_net] [613.053139] vhost_worker+0x166/0x200 [vhost] [613.053139] ? vhost_dev_init+0x580/0x580 [vhost] [613.053139] ? __kthread_parkme+0x77/0x90 [613.053139] ? vhost_dev_init+0x580/0x580 [vhost] [613.053139] kthread+0x1b1/0x1d0 [613.053139] ? kthread_park+0xb0/0xb0 [613.053139] ret_from_fork+0x35/0x40 [613.088705] [613.088705] Allocated by task 1155: [613.088705] kasan_kmalloc+0xbf/0xe0 [613.088705] kmem_cache_alloc+0xdc/0x220 [613.088705] __build_skb+0x2a/0x160 [613.088705] build_skb+0x14/0xc0 [613.088705] tun_sendmsg+0x4f0/0xc50 [tun] [613.088705] vhost_tx_batch.isra.14+0xeb/0x1f0 [vhost_net] [613.088705] handle_tx_copy+0x2d0/0x8f0 [vhost_net] [613.088705] handle_tx+0xc7/0x120 [vhost_net] [613.088705] vhost_worker+0x166/0x200 [vhost] [613.088705] kthread+0x1b1/0x1d0 [613.088705] ret_from_fork+0x35/0x40 [613.088705] [613.088705] Freed by task 1155: [613.088705] __kasan_slab_free+0x12e/0x180 [613.088705] kmem_cache_free+0xa0/0x230 [613.088705] ip6_mc_input+0x40f/0x5a0 [613.088705] ipv6_rcv+0xc9/0x1e0 [613.088705] __netif_receive_skb_one_core+0xc1/0x100 [613.088705] netif_receive_skb_internal+0xc4/0x270 [613.088705] br_pass_frame_up+0x2b9/0x2e0 [613.088705] br_handle_frame_finish+0x2fb/0x7a0 [613.088705] br_handle_frame+0x30f/0x6c0 [613.088705] __netif_receive_skb_core+0x61a/0x15b0 [613.088705] __netif_receive_skb_one_core+0x8e/0x100 [613.088705] netif_receive_skb_internal+0xc4/0x270 [613.088705] tun_sendmsg+0x738/0xc50 [tun] [613.088705] vhost_tx_batch.isra.14+0xeb/0x1f0 [vhost_net] [613.088705] handle_tx_copy+0x2d0/0x8f0 [vhost_net] [613.088705] handle_tx+0xc7/0x120 [vhost_net] [613.088705] vhost_worker+0x166/0x200 [vhost] [613.088705] kthread+0x1b1/0x1d0 [613.088705] ret_from_fork+0x35/0x40 [613.088705] [613.088705] The buggy address belongs to the object at ffff8881da9ab740 [613.088705] which belongs to the cache skbuff_head_cache of size 232 Fixes: 043d222f93ab ("tuntap: accept an array of XDP buffs through sendmsg()") Reviewed-by: Toshiaki Makita <[email protected]> Signed-off-by: Prashant Bhole <[email protected]> Acked-by: Jason Wang <[email protected]> Acked-by: Michael S. Tsirkin <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2018-12-03net: 8139cp: fix a BUG triggered by changing mtu with network trafficSu Yanjun1-0/+5
When changing mtu many times with traffic, a bug is triggered: [ 1035.684037] kernel BUG at lib/dynamic_queue_limits.c:26! [ 1035.684042] invalid opcode: 0000 [#1] SMP [ 1035.684049] Modules linked in: loop binfmt_misc 8139cp(OE) macsec tcp_diag udp_diag inet_diag unix_diag af_packet_diag netlink_diag tcp_lp fuse uinput xt_CHECKSUM iptable_mangle ipt_MASQUERADE nf_nat_masquerade_ipv4 iptable_nat nf_nat_ipv4 nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 xt_conntrack nf_conntrack ipt_REJECT nf_reject_ipv4 tun bridge stp llc ebtable_filter ebtables ip6table_filter devlink ip6_tables iptable_filter sunrpc snd_hda_codec_generic snd_hda_intel snd_hda_codec snd_hda_core snd_hwdep ppdev snd_seq iosf_mbi crc32_pclmul parport_pc snd_seq_device ghash_clmulni_intel parport snd_pcm aesni_intel joydev lrw snd_timer virtio_balloon sg gf128mul glue_helper ablk_helper cryptd snd soundcore i2c_piix4 pcspkr ip_tables xfs libcrc32c sr_mod sd_mod cdrom crc_t10dif crct10dif_generic ata_generic [ 1035.684102] pata_acpi virtio_console qxl drm_kms_helper syscopyarea sysfillrect sysimgblt floppy fb_sys_fops crct10dif_pclmul crct10dif_common ttm crc32c_intel serio_raw ata_piix drm libata 8139too virtio_pci drm_panel_orientation_quirks virtio_ring virtio mii dm_mirror dm_region_hash dm_log dm_mod [last unloaded: 8139cp] [ 1035.684132] CPU: 9 PID: 25140 Comm: if-mtu-change Kdump: loaded Tainted: G OE ------------ T 3.10.0-957.el7.x86_64 #1 [ 1035.684134] Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011 [ 1035.684136] task: ffff8f59b1f5a080 ti: ffff8f5a2e32c000 task.ti: ffff8f5a2e32c000 [ 1035.684149] RIP: 0010:[<ffffffffba3a40d0>] [<ffffffffba3a40d0>] dql_completed+0x180/0x190 [ 1035.684162] RSP: 0000:ffff8f5a75483e50 EFLAGS: 00010093 [ 1035.684162] RAX: 00000000000000c2 RBX: ffff8f5a6f91c000 RCX: 0000000000000000 [ 1035.684162] RDX: 0000000000000000 RSI: 0000000000000184 RDI: ffff8f599fea3ec0 [ 1035.684162] RBP: ffff8f5a75483ea8 R08: 00000000000000c2 R09: 0000000000000000 [ 1035.684162] R10: 00000000000616ef R11: ffff8f5a75483b56 R12: ffff8f599fea3e00 [ 1035.684162] R13: 0000000000000001 R14: 0000000000000000 R15: 0000000000000184 [ 1035.684162] FS: 00007fa8434de740(0000) GS:ffff8f5a75480000(0000) knlGS:0000000000000000 [ 1035.684162] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 1035.684162] CR2: 00000000004305d0 CR3: 000000024eb66000 CR4: 00000000001406e0 [ 1035.684162] Call Trace: [ 1035.684162] <IRQ> [ 1035.684162] [<ffffffffc08cbaf8>] ? cp_interrupt+0x478/0x580 [8139cp] [ 1035.684162] [<ffffffffba14a294>] __handle_irq_event_percpu+0x44/0x1c0 [ 1035.684162] [<ffffffffba14a442>] handle_irq_event_percpu+0x32/0x80 [ 1035.684162] [<ffffffffba14a4cc>] handle_irq_event+0x3c/0x60 [ 1035.684162] [<ffffffffba14db29>] handle_fasteoi_irq+0x59/0x110 [ 1035.684162] [<ffffffffba02e554>] handle_irq+0xe4/0x1a0 [ 1035.684162] [<ffffffffba7795dd>] do_IRQ+0x4d/0xf0 [ 1035.684162] [<ffffffffba76b362>] common_interrupt+0x162/0x162 [ 1035.684162] <EOI> [ 1035.684162] [<ffffffffba0c2ae4>] ? __wake_up_bit+0x24/0x70 [ 1035.684162] [<ffffffffba1e46f5>] ? do_set_pte+0xd5/0x120 [ 1035.684162] [<ffffffffba1b64fb>] unlock_page+0x2b/0x30 [ 1035.684162] [<ffffffffba1e4879>] do_read_fault.isra.61+0x139/0x1b0 [ 1035.684162] [<ffffffffba1e9134>] handle_pte_fault+0x2f4/0xd10 [ 1035.684162] [<ffffffffba1ebc6d>] handle_mm_fault+0x39d/0x9b0 [ 1035.684162] [<ffffffffba76f5e3>] __do_page_fault+0x203/0x500 [ 1035.684162] [<ffffffffba76f9c6>] trace_do_page_fault+0x56/0x150 [ 1035.684162] [<ffffffffba76ef42>] do_async_page_fault+0x22/0xf0 [ 1035.684162] [<ffffffffba76b788>] async_page_fault+0x28/0x30 [ 1035.684162] Code: 54 c7 47 54 ff ff ff ff 44 0f 49 ce 48 8b 35 48 2f 9c 00 48 89 77 58 e9 fe fe ff ff 0f 1f 80 00 00 00 00 41 89 d1 e9 ef fe ff ff <0f> 0b 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 55 8d 42 ff 48 [ 1035.684162] RIP [<ffffffffba3a40d0>] dql_completed+0x180/0x190 [ 1035.684162] RSP <ffff8f5a75483e50> It's not the same as in 7fe0ee09 patch described. As 8139cp uses shared irq mode, other device irq will trigger cp_interrupt to execute. cp_change_mtu -> cp_close -> cp_open In cp_close routine just before free_irq(), some interrupt may occur. In my environment, cp_interrupt exectutes and IntrStatus is 0x4, exactly TxOk. That will cause cp_tx to wake device queue. As device queue is started, cp_start_xmit and cp_open will run at same time which will cause kernel BUG. For example: [#] for tx descriptor At start: [#][#][#] num_queued=3 After cp_init_hw->cp_start_hw->netdev_reset_queue: [#][#][#] num_queued=0 When 8139cp starts to work then cp_tx will check num_queued mismatchs the complete_bytes. The patch will check IntrMask before check IntrStatus in cp_interrupt. When 8139cp interrupt is disabled, just return. Signed-off-by: Su Yanjun <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2018-12-03IB/mlx5: Fix implicit ODP interrupted page faultArtemy Kovalyov1-5/+4
Since any page fault may be interrupted by a MMU invalidation and implicit leaf MR may be released during this process. The check for parent value is unreliable condition for an implicit MR. Use other condition that we can rely on to determine if MR is implicit. Fixes: b4cfe447d47b ("IB/mlx5: Implement on demand paging by adding support for MMU notifiers") Signed-off-by: Artemy Kovalyov <[email protected]> Signed-off-by: Moni Shoua <[email protected]> Signed-off-by: Leon Romanovsky <[email protected]> Signed-off-by: Doug Ledford <[email protected]>
2018-12-03net: phy: don't allow __set_phy_supported to add unsupported modesHeiner Kallweit1-11/+8
Currently __set_phy_supported allows to add modes w/o checking whether the PHY supports them. This is wrong, it should never add modes but only remove modes we don't want to support. The commit marked as fixed didn't do anything wrong, it just copied existing functionality to the helper which is being fixed now. Fixes: f3a6bd393c2c ("phylib: Add phy_set_max_speed helper") Signed-off-by: Heiner Kallweit <[email protected]> Reviewed-by: Andrew Lunn <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2018-12-03Merge tag 'arm-soc/for-4.20/devicetree-fixes' of ↵Olof Johansson2-2/+2
https://github.com/Broadcom/stblinux into fixes This pull request contains Broadcom ARM-based SoCs Device Tree fixes, please pull the following for 4.20: - Stefan fixes the polariy of the Wi-Fi reset GPIOs signals which would break on Raspberry Pi 3B and 3B+ * tag 'arm-soc/for-4.20/devicetree-fixes' of https://github.com/Broadcom/stblinux: ARM: dts: bcm2837: Fix polarity of wifi reset GPIOs Signed-off-by: Olof Johansson <[email protected]>
2018-12-03IB/hfi1: Fix an out-of-bounds access in get_hw_statsPiotr Stankiewicz3-2/+5
When running with KASAN, the following trace is produced: [ 62.535888] ================================================================== [ 62.544930] BUG: KASAN: slab-out-of-bounds in gut_hw_stats+0x122/0x230 [hfi1] [ 62.553856] Write of size 8 at addr ffff88080e8d6330 by task kworker/0:1/14 [ 62.565333] CPU: 0 PID: 14 Comm: kworker/0:1 Not tainted 4.19.0-test-build-kasan+ #8 [ 62.575087] Hardware name: Intel Corporation S2600KPR/S2600KPR, BIOS SE5C610.86B.01.01.0019.101220160604 10/12/2016 [ 62.587951] Workqueue: events work_for_cpu_fn [ 62.594050] Call Trace: [ 62.598023] dump_stack+0xc6/0x14c [ 62.603089] ? dump_stack_print_info.cold.1+0x2f/0x2f [ 62.610041] ? kmsg_dump_rewind_nolock+0x59/0x59 [ 62.616615] ? get_hw_stats+0x122/0x230 [hfi1] [ 62.622985] print_address_description+0x6c/0x23c [ 62.629744] ? get_hw_stats+0x122/0x230 [hfi1] [ 62.636108] kasan_report.cold.6+0x241/0x308 [ 62.642365] get_hw_stats+0x122/0x230 [hfi1] [ 62.648703] ? hfi1_alloc_rn+0x40/0x40 [hfi1] [ 62.655088] ? __kmalloc+0x110/0x240 [ 62.660695] ? hfi1_alloc_rn+0x40/0x40 [hfi1] [ 62.667142] setup_hw_stats+0xd8/0x430 [ib_core] [ 62.673972] ? show_hfi+0x50/0x50 [hfi1] [ 62.680026] ib_device_register_sysfs+0x165/0x180 [ib_core] [ 62.687995] ib_register_device+0x5a2/0xa10 [ib_core] [ 62.695340] ? show_hfi+0x50/0x50 [hfi1] [ 62.701421] ? ib_unregister_device+0x2e0/0x2e0 [ib_core] [ 62.709222] ? __vmalloc_node_range+0x2d0/0x380 [ 62.716131] ? rvt_driver_mr_init+0x11f/0x2d0 [rdmavt] [ 62.723735] ? vmalloc_node+0x5c/0x70 [ 62.729697] ? rvt_driver_mr_init+0x11f/0x2d0 [rdmavt] [ 62.737347] ? rvt_driver_mr_init+0x1f5/0x2d0 [rdmavt] [ 62.744998] ? __rvt_alloc_mr+0x110/0x110 [rdmavt] [ 62.752315] ? rvt_rc_error+0x140/0x140 [rdmavt] [ 62.759434] ? rvt_vma_open+0x30/0x30 [rdmavt] [ 62.766364] ? mutex_unlock+0x1d/0x40 [ 62.772445] ? kmem_cache_create_usercopy+0x15d/0x230 [ 62.780115] rvt_register_device+0x1f6/0x360 [rdmavt] [ 62.787823] ? rvt_get_port_immutable+0x180/0x180 [rdmavt] [ 62.796058] ? __get_txreq+0x400/0x400 [hfi1] [ 62.802969] ? memcpy+0x34/0x50 [ 62.808611] hfi1_register_ib_device+0xde6/0xeb0 [hfi1] [ 62.816601] ? hfi1_get_npkeys+0x10/0x10 [hfi1] [ 62.823760] ? hfi1_init+0x89f/0x9a0 [hfi1] [ 62.830469] ? hfi1_setup_eagerbufs+0xad0/0xad0 [hfi1] [ 62.838204] ? pcie_capability_clear_and_set_word+0xcd/0xe0 [ 62.846429] ? pcie_capability_read_word+0xd0/0xd0 [ 62.853791] ? hfi1_pcie_init+0x187/0x4b0 [hfi1] [ 62.860958] init_one+0x67f/0xae0 [hfi1] [ 62.867301] ? hfi1_init+0x9a0/0x9a0 [hfi1] [ 62.873876] ? wait_woken+0x130/0x130 [ 62.879860] ? read_word_at_a_time+0xe/0x20 [ 62.886329] ? strscpy+0x14b/0x280 [ 62.891998] ? hfi1_init+0x9a0/0x9a0 [hfi1] [ 62.898405] local_pci_probe+0x70/0xd0 [ 62.904295] ? pci_device_shutdown+0x90/0x90 [ 62.910833] work_for_cpu_fn+0x29/0x40 [ 62.916750] process_one_work+0x584/0x960 [ 62.922974] ? rcu_work_rcufn+0x40/0x40 [ 62.928991] ? __schedule+0x396/0xdc0 [ 62.934806] ? __sched_text_start+0x8/0x8 [ 62.941020] ? pick_next_task_fair+0x68b/0xc60 [ 62.947674] ? run_rebalance_domains+0x260/0x260 [ 62.954471] ? __list_add_valid+0x29/0xa0 [ 62.960607] ? move_linked_works+0x1c7/0x230 [ 62.967077] ? trace_event_raw_event_workqueue_execute_start+0x140/0x140 [ 62.976248] ? mutex_lock+0xa6/0x100 [ 62.982029] ? __mutex_lock_slowpath+0x10/0x10 [ 62.988795] ? __switch_to+0x37a/0x710 [ 62.994731] worker_thread+0x62e/0x9d0 [ 63.000602] ? max_active_store+0xf0/0xf0 [ 63.006828] ? __switch_to_asm+0x40/0x70 [ 63.012932] ? __switch_to_asm+0x34/0x70 [ 63.019013] ? __switch_to_asm+0x40/0x70 [ 63.025042] ? __switch_to_asm+0x34/0x70 [ 63.031030] ? __switch_to_asm+0x40/0x70 [ 63.037006] ? __schedule+0x396/0xdc0 [ 63.042660] ? kmem_cache_alloc_trace+0xf3/0x1f0 [ 63.049323] ? kthread+0x59/0x1d0 [ 63.054594] ? ret_from_fork+0x35/0x40 [ 63.060257] ? __sched_text_start+0x8/0x8 [ 63.066212] ? schedule+0xcf/0x250 [ 63.071529] ? __wake_up_common+0x110/0x350 [ 63.077794] ? __schedule+0xdc0/0xdc0 [ 63.083348] ? wait_woken+0x130/0x130 [ 63.088963] ? finish_task_switch+0x1f1/0x520 [ 63.095258] ? kasan_unpoison_shadow+0x30/0x40 [ 63.101792] ? __init_waitqueue_head+0xa0/0xd0 [ 63.108183] ? replenish_dl_entity.cold.60+0x18/0x18 [ 63.115151] ? _raw_spin_lock_irqsave+0x25/0x50 [ 63.121754] ? max_active_store+0xf0/0xf0 [ 63.127753] kthread+0x1ae/0x1d0 [ 63.132894] ? kthread_bind+0x30/0x30 [ 63.138422] ret_from_fork+0x35/0x40 [ 63.146973] Allocated by task 14: [ 63.152077] kasan_kmalloc+0xbf/0xe0 [ 63.157471] __kmalloc+0x110/0x240 [ 63.162804] init_cntrs+0x34d/0xdf0 [hfi1] [ 63.168883] hfi1_init_dd+0x29a3/0x2f90 [hfi1] [ 63.175244] init_one+0x551/0xae0 [hfi1] [ 63.181065] local_pci_probe+0x70/0xd0 [ 63.186759] work_for_cpu_fn+0x29/0x40 [ 63.192310] process_one_work+0x584/0x960 [ 63.198163] worker_thread+0x62e/0x9d0 [ 63.203843] kthread+0x1ae/0x1d0 [ 63.208874] ret_from_fork+0x35/0x40 [ 63.217203] Freed by task 1: [ 63.221844] __kasan_slab_free+0x12e/0x180 [ 63.227844] kfree+0x92/0x1a0 [ 63.232570] single_release+0x3a/0x60 [ 63.238024] __fput+0x1d9/0x480 [ 63.242911] task_work_run+0x139/0x190 [ 63.248440] exit_to_usermode_loop+0x191/0x1a0 [ 63.254814] do_syscall_64+0x301/0x330 [ 63.260283] entry_SYSCALL_64_after_hwframe+0x44/0xa9 [ 63.270199] The buggy address belongs to the object at ffff88080e8d5500 which belongs to the cache kmalloc-4096 of size 4096 [ 63.287247] The buggy address is located 3632 bytes inside of 4096-byte region [ffff88080e8d5500, ffff88080e8d6500) [ 63.303564] The buggy address belongs to the page: [ 63.310447] page:ffffea00203a3400 count:1 mapcount:0 mapping:ffff88081380e840 index:0x0 compound_mapcount: 0 [ 63.323102] flags: 0x2fffff80008100(slab|head) [ 63.329775] raw: 002fffff80008100 0000000000000000 0000000100000001 ffff88081380e840 [ 63.340175] raw: 0000000000000000 0000000000070007 00000001ffffffff 0000000000000000 [ 63.350564] page dumped because: kasan: bad access detected [ 63.361974] Memory state around the buggy address: [ 63.369137] ffff88080e8d6200: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 63.379082] ffff88080e8d6280: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 63.389032] >ffff88080e8d6300: 00 00 00 00 00 00 fc fc fc fc fc fc fc fc fc fc [ 63.398944] ^ [ 63.406141] ffff88080e8d6380: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc [ 63.416109] ffff88080e8d6400: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc [ 63.426099] ================================================================== The trace happens because get_hw_stats() assumes there is room in the memory allocated in init_cntrs() to accommodate the driver counters. Unfortunately, that routine only allocated space for the device counters. Fix by insuring the allocation has room for the additional driver counters. Cc: <[email protected]> # v4.14+ Fixes: b7481944b06e9 ("IB/hfi1: Show statistics counters under IB stats interface") Reviewed-by: Mike Marciniczyn <[email protected]> Reviewed-by: Mike Ruhl <[email protected]> Signed-off-by: Piotr Stankiewicz <[email protected]> Signed-off-by: Dennis Dalessandro <[email protected]> Signed-off-by: Doug Ledford <[email protected]>
2018-12-03IB/hfi1: Fix a latency issue for small messagesMichael J. Ruhl1-0/+7
A recent performance enhancement introduced a latency issue in the HFI message path. The new algorithm removed a forced call send for PIO messages and added a forced schedule event for messages larger than the MTU. For PIO, the schedule path can introduce thrashing that can significantly impact the throughput for small messages. If a message size is within the PIO threshold, always take the send path. Fixes: 0b79b27748cb ("IB/{hfi1, qib, rdmavt}: Schedule multi RC/UC packets instead of posting") Reviewed-by: Mike Marciniszyn <[email protected]> Signed-off-by: Michael J. Ruhl <[email protected]> Signed-off-by: Dennis Dalessandro <[email protected]> Signed-off-by: Doug Ledford <[email protected]>
2018-12-03ARM: dts: realview: Fix some more duplicate regulator nodesRob Herring2-4/+4
There's a bug in dtc in checking for duplicate node names when there's another section (e.g. "/ { };"). In this case, skeleton.dtsi provides another section. Upon removal of skeleton.dtsi, the dtb fails to build due to a duplicate node 'fixedregulator@0'. As both nodes were pretty much the same 3.3V fixed regulator, it hasn't really mattered. Fix this by renaming the nodes to something unique. In the process, drop the unit-address which shouldn't be present wtihout reg property. Signed-off-by: Rob Herring <[email protected]> Reviewed-by: Linus Walleij <[email protected]> Signed-off-by: Olof Johansson <[email protected]>
2018-12-03MAINTAINERS: update entry for MMP platformLubomir Rintel2-5/+10
Move Eric Miao and Haojian Zhuang over to CREDITS, since they're AWOL for some time already. The git trees have gone away too. I'm adding myself as a reviewer. I'd like to be Cc'd on patches and will be able to test them, but I don't possess a data sheet thus there might be things I'll be unable to review. Hence the Odd-Fixes status. Signed-off-by: Lubomir Rintel <[email protected]> Signed-off-by: Olof Johansson <[email protected]>
2018-12-03ARM: mmp/mmp2: fix cpu_is_mmp2() on mmp2-dtLubomir Rintel1-2/+4
cpu_is_mmp2() was equivalent to cpu_is_pj4(), wouldn't be correct for multiplatform kernels. Fix it by also considering mmp_chip_id, as is done for cpu_is_pxa168() and cpu_is_pxa910() above. Moreover, it is only available with CONFIG_CPU_MMP2 and thus doesn't work on DT-based MMP2 machines. Enable it on CONFIG_MACH_MMP2_DT too. Note: CONFIG_CPU_MMP2 is only used for machines that use board files instead of DT. It should perhaps be renamed. I'm not doing it now, because I don't have a better idea. Signed-off-by: Lubomir Rintel <[email protected]> Acked-by: Arnd Bergmann <[email protected]> Cc: [email protected] Signed-off-by: Olof Johansson <[email protected]>
2018-12-03Merge tag 'v4.19-next-fixes' of ↵Olof Johansson3-12/+12
https://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into fixes DT mt7622: - Kernelci awaits a working stdout-path. Fix the path for reference board and bananapi-r64 - General propouse timer has issues with clocks that didn't get probed early. Delete the DT node as the timer isn't need, a ARM arch timer exists on the system. * tag 'v4.19-next-fixes' of https://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux: arm64: dts: mt7622: Drop the general purpose timer node arm64: dts: mt7622: fix no more console output on BPI-R64 board arm64: dts: mt7622: fix no more console output on rfb1 Signed-off-by: Olof Johansson <[email protected]>
2018-12-03MAINTAINERS: mediatek: Update SoC entryMatthias Brugger1-0/+4
Add IRC channel and URL of the wiki. Also add soc drivers folder and regex to catch more mediatek components. Signed-off-by: Matthias Brugger <[email protected]> Signed-off-by: Olof Johansson <[email protected]>
2018-12-03media: vicodec: set state resolution from raw formatHans Verkuil1-3/+10
The state structure contains the resolution expected by the decoder and encoder. For an encoder that resolution should be taken from the OUTPUT format, and for a decoder from the CAPTURE format. If the wrong format is picked, a buffer overrun can occur if there is a mismatch between the CAPTURE and OUTPUT formats. The real fix would be to correctly implement the stateful codec specification, but that will take more time. For now just prevent the buffer overrun. Signed-off-by: Hans Verkuil <[email protected]> Signed-off-by: Mauro Carvalho Chehab <[email protected]>
2018-12-03media: vivid: drop v4l2_ctrl_request_complete() from start_streamingHans Verkuil5-10/+0
If start_streaming() fails and all queued buffers are returned to vb2, then do not call v4l2_ctrl_request_complete(). Nothing happened to the request and the state should remain as it was before start_streaming was called. Signed-off-by: Hans Verkuil <[email protected]> Acked-by: Sakari Ailus <[email protected]> Signed-off-by: Hans Verkuil <[email protected]> Signed-off-by: Mauro Carvalho Chehab <[email protected]>
2018-12-03media: vb2: don't unbind/put the object when going to state QUEUEDHans Verkuil1-1/+1
When a buffer is returned to state QUEUED (that happens when start_streaming fails), then do not unbind and put the object from the request. Nothing has changed yet, so just keep it as is. Signed-off-by: Hans Verkuil <[email protected]> Acked-by: Sakari Ailus <[email protected]> Signed-off-by: Hans Verkuil <[email protected]> Signed-off-by: Mauro Carvalho Chehab <[email protected]>
2018-12-03media: vb2: keep a reference to the request until dqbufHans Verkuil2-5/+35
When vb2_buffer_done is called the buffer is unbound from the request and put. The media_request_object_put also 'put's the request reference. If the application has already closed the request fd, then that means that the request reference at that point goes to 0 and the whole request is released. This means that the control handler associated with the request is also freed and that causes this kernel oops: [174705.995401] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:908 [174705.995411] in_atomic(): 1, irqs_disabled(): 1, pid: 28071, name: vivid-000-vid-o [174705.995416] 2 locks held by vivid-000-vid-o/28071: [174705.995420] #0: 000000001ea3a232 (&dev->mutex#3){....}, at: vivid_thread_vid_out+0x3f5/0x550 [vivid] [174705.995447] #1: 00000000e30a0d1e (&(&q->done_lock)->rlock){....}, at: vb2_buffer_done+0x92/0x1d0 [videobuf2_common] [174705.995460] Preemption disabled at: [174705.995461] [<0000000000000000>] (null) [174705.995472] CPU: 11 PID: 28071 Comm: vivid-000-vid-o Tainted: G W 4.20.0-rc1-test-no #88 [174705.995476] Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 05/19/2017 [174705.995481] Call Trace: [174705.995500] dump_stack+0x46/0x60 [174705.995512] ___might_sleep.cold.79+0xe1/0xf1 [174705.995523] __mutex_lock+0x50/0x8f0 [174705.995531] ? find_held_lock+0x2d/0x90 [174705.995536] ? find_held_lock+0x2d/0x90 [174705.995542] ? find_held_lock+0x2d/0x90 [174705.995564] ? v4l2_ctrl_handler_free.part.13+0x44/0x1d0 [videodev] [174705.995576] v4l2_ctrl_handler_free.part.13+0x44/0x1d0 [videodev] [174705.995590] v4l2_ctrl_request_release+0x1c/0x30 [videodev] [174705.995600] media_request_clean+0x64/0xe0 [media] [174705.995609] media_request_release+0x19/0x40 [media] [174705.995617] vb2_buffer_done+0xef/0x1d0 [videobuf2_common] [174705.995630] vivid_thread_vid_out+0x2c1/0x550 [vivid] [174705.995645] ? vivid_stop_generating_vid_cap+0x1c0/0x1c0 [vivid] [174705.995653] kthread+0x113/0x130 [174705.995659] ? kthread_park+0x80/0x80 [174705.995667] ret_from_fork+0x35/0x40 The vb2_buffer_done function can be called from interrupt context, so anything that sleeps is not allowed. The solution is to increment the request refcount when the buffer is queued and decrement it when the buffer is dequeued. Releasing the request is fine if that happens from VIDIOC_DQBUF. Signed-off-by: Hans Verkuil <[email protected]> Acked-by: Sakari Ailus <[email protected]> Signed-off-by: Hans Verkuil <[email protected]> Signed-off-by: Mauro Carvalho Chehab <[email protected]>
2018-12-03media: vb2: skip request checks for VIDIOC_PREPARE_BUFHans Verkuil1-4/+7
VIDIOC_PREPARE_BUF should ignore V4L2_BUF_FLAG_REQUEST_FD since it isn't doing anything with requests. So inform vb2_queue_or_prepare_buf whether it is called from vb2_prepare_buf or vb2_qbuf and just return 0 in the first case. This was found when adding new v4l2-compliance checks. Signed-off-by: Hans Verkuil <[email protected]> Acked-by: Sakari Ailus <[email protected]> Signed-off-by: Hans Verkuil <[email protected]> Signed-off-by: Mauro Carvalho Chehab <[email protected]>
2018-12-03media: vb2: don't call __vb2_queue_cancel if vb2_start_streaming failedHans Verkuil1-3/+1
vb2_start_streaming() already rolls back the buffers, so there is no need to call __vb2_queue_cancel(). Especially since __vb2_queue_cancel() does too much, such as zeroing the q->queued_count value, causing vb2 to think that no buffers have been queued. It appears that this call to __vb2_queue_cancel() is a left-over from before commit b3379c6201bb3. Fixes: b3379c6201bb3 ('vb2: only call start_streaming if sufficient buffers are queued') Signed-off-by: Hans Verkuil <[email protected]> Cc: <[email protected]> # for v4.16 and up Acked-by: Sakari Ailus <[email protected]> Signed-off-by: Mauro Carvalho Chehab <[email protected]>
2018-12-03media: cedrus: Fix a NULL vs IS_ERR() checkDan Carpenter1-2/+2
The devm_ioremap_resource() function doesn't return NULL pointers, it returns error pointers. Fixes: 50e761516f2b ("media: platform: Add Cedrus VPU decoder driver") Signed-off-by: Dan Carpenter <[email protected]> Acked-by: Paul Kocialkowski <[email protected]> Signed-off-by: Hans Verkuil <[email protected]> Signed-off-by: Mauro Carvalho Chehab <[email protected]>
2018-12-03media: vsp1: Fix LIF buffer thresholdsLaurent Pinchart1-1/+1
Commit de2bc45c84f7 ("media: vsp1: Update LIF buffer thresholds") updated the LIF buffer thresholds based on the VSP version, but used the wrong model mask. This resulted in all VSP instances to be treated as a Gen3 VSPD, breaking operation on all Gen2 platforms as well as on H3 ES2.0, M3-N, V3M and V3H. Fix it. Fixes: de2bc45c84f7 ("media: vsp1: Update LIF buffer thresholds") Reported-by: Colin Ian King <[email protected]> Signed-off-by: Laurent Pinchart <[email protected]> Reviewed-by: Kieran Bingham <[email protected]> Signed-off-by: Mauro Carvalho Chehab <[email protected]>
2018-12-03libata: whitelist all SAMSUNG MZ7KM* solid-state disksJuha-Matti Tilli1-0/+1
These devices support read zero after trim (RZAT), as they advertise to the OS. However, the OS doesn't believe the SSDs unless they are explicitly whitelisted. Acked-by: Martin K. Petersen <[email protected]> Signed-off-by: Juha-Matti Tilli <[email protected]> Signed-off-by: Jens Axboe <[email protected]>
2018-12-03ARM: dts: bcm2837: Fix polarity of wifi reset GPIOsStefan Wahren2-2/+2
The commit b1b8f45b3130 ("ARM: dts: bcm2837: Add missing GPIOs of Expander") introduced a wifi power sequence. Unfortunately the polarity of the reset GPIOs were wrong and broke the wifi support on Raspberry Pi 3 B and later in 3 B+. This wasn't discovered before since the power sequence takes only effect in case the relevant MMC driver is compiled as a module. Fixes: b1b8f45b3130 ("ARM: dts: bcm2837: Add missing GPIOs of Expander") Cc: [email protected] Reported-by: Matthias Lueschner <[email protected]> Link: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=911443 Signed-off-by: Stefan Wahren <[email protected]> Reviewed-by: Eric Anholt <[email protected]> Signed-off-by: Florian Fainelli <[email protected]>
2018-12-03Input: omap-keypad - fix keyboard debounce configurationTony Lindgren1-4/+14
I noticed that the Android v3.0.8 kernel on droid4 is using different keypad values from the mainline kernel and does not have issues with keys occasionally being stuck until pressed again. Turns out there was an earlier patch posted to fix this as "Input: omap-keypad: errata i689: Correct debounce time", but it was never reposted to fix use macros for timing calculations. This updated version is using macros, and also fixes the use of the input clock rate to use 32768KiHz instead of 32000KiHz. And we want to use the known good Android kernel values of 3 and 6 instead of 2 and 6 in the earlier patch. Reported-by: Pavel Machek <[email protected]> Signed-off-by: Tony Lindgren <[email protected]> Signed-off-by: Dmitry Torokhov <[email protected]>
2018-12-03Input: xpad - quirk all PDP Xbox One gamepadsCameron Gutman1-10/+6
Since we continue to find tons of new variants [0,1,2,3,4,5,6] that need the PDP quirk, let's just quirk all devices from PDP. [0]: https://github.com/paroj/xpad/pull/104 [1]: https://github.com/paroj/xpad/pull/105 [2]: https://github.com/paroj/xpad/pull/108 [3]: https://github.com/paroj/xpad/pull/109 [4]: https://github.com/paroj/xpad/pull/112 [5]: https://github.com/paroj/xpad/pull/115 [6]: https://github.com/paroj/xpad/pull/116 Fixes: e5c9c6a885fa ("Input: xpad - add support for PDP Xbox One controllers") Cc: [email protected] Signed-off-by: Cameron Gutman <[email protected]> Signed-off-by: Dmitry Torokhov <[email protected]>
2018-12-03Input: synaptics - enable SMBus for HP 15-ay000Teika Kazura1-0/+1
SMBus works fine for the touchpad with id SYN3221, used in the HP 15-ay000 series, This device has been reported in these messages in the "linux-input" mailing list: * https://marc.info/?l=linux-input&m=152016683003369&w=2 * https://www.spinics.net/lists/linux-input/msg52525.html Reported-by: Nitesh Debnath <[email protected]> Reported-by: Teika Kazura <[email protected]> Signed-off-by: Teika Kazura <[email protected]> Reviewed-by: Benjamin Tissoires <[email protected]> Signed-off-by: Dmitry Torokhov <[email protected]>
2018-12-03Input: synaptics - add PNP ID for ThinkPad P50 to SMBusLyude Paul1-0/+1
Noticed the other day the trackpoint felt different on my P50, then realized it was because rmi4 wasn't loading for this machine automatically. Suspend/resume, hibernate, and everything else seem to work perfectly fine on here. Signed-off-by: Lyude Paul <[email protected]> Cc: [email protected] Signed-off-by: Dmitry Torokhov <[email protected]>
2018-12-03Input: elan_i2c - add ACPI ID for Lenovo IdeaPad 330-15ARRNoah Westervelt1-0/+1
Add ELAN061E to the ACPI table to support Elan touchpad found in Lenovo IdeaPad 330-15ARR. Signed-off-by: Noah Westervelt <[email protected]> Cc: [email protected] Signed-off-by: Dmitry Torokhov <[email protected]>
2018-12-03Input: elan_i2c - add support for ELAN0621 touchpadAdam Wong1-0/+1
Added the ability to detect the ELAN0621 touchpad found in some Lenovo laptops. Signed-off-by: Adam Wong <[email protected]> Cc: [email protected] Signed-off-by: Dmitry Torokhov <[email protected]>
2018-12-03Merge tag 'media/v4.20-4' of ↵Linus Torvalds14-101/+240
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media Pull media fixes from Mauro Carvalho Chehab: - Revert a dt-bindings patch whose driver didn't make for 4.20 - fix a kernel oops at vicodec driver - fix a frame overflow at gspca with was causing regressions on some cameras, making them to not work - use the proper type for wait_queue head - make media request API compatible with 32-bit userspace on 64-bit kernel - fix a regression on Kernel 4.19 at dvb-pll - don't use SPDX headers yet for GFDL * tag 'media/v4.20-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: media: mediactl docs: Fix licensing message media: dvb-pll: don't re-validate tuner frequencies media: dvb-pll: fix tuner frequency ranges media: Revert "media: dt-bindings: Document the Rockchip VPU bindings" media: gspca: fix frame overflow error media: vicodec: fix memchr() kernel oops media: cedrus: add action item to the TODO media: media-request: Add compat ioctl media: Use wait_queue_head_t for media_request
2018-12-03clk: zynqmp: Off by one in zynqmp_is_valid_clock()Dan Carpenter1-1/+1
The > comparison should be >= to prevent reading beyond the end of the clock[] array. (The clock[] array is allocated in zynqmp_clk_setup() and has clock_max_idx elements.) Fixes: 3fde0e16d016 ("drivers: clk: Add ZynqMP clock driver") Signed-off-by: Dan Carpenter <[email protected]> Signed-off-by: Stephen Boyd <[email protected]>
2018-12-03clk: mmp: Off by one in mmp_clk_add()Dan Carpenter1-1/+1
The > comparison should be >= or we write one element beyond the end of the unit->clk_table[] array. (The unit->clk_table[] array is allocated in the mmp_clk_init() function and it has unit->nr_clks elements). Fixes: 4661fda10f8b ("clk: mmp: add basic support functions for DT support") Signed-off-by: Dan Carpenter <[email protected]> Signed-off-by: Stephen Boyd <[email protected]>
2018-12-03clk: mvebu: Off by one bugs in cp110_of_clk_get()Dan Carpenter1-2/+2
These > comparisons should be >= to prevent reading beyond the end of of the clk_data->hws[] buffer. The clk_data->hws[] array is allocated in cp110_syscon_common_probe() when we do: cp110_clk_data = devm_kzalloc(dev, sizeof(*cp110_clk_data) + sizeof(struct clk_hw *) * CP110_CLK_NUM, GFP_KERNEL); As you can see, it has CP110_CLK_NUM elements which is equivalent to CP110_MAX_CORE_CLOCKS + CP110_MAX_GATABLE_CLOCKS. Fixes: d3da3eaef7f4 ("clk: mvebu: new driver for Armada CP110 system controller") Signed-off-by: Dan Carpenter <[email protected]> Signed-off-by: Stephen Boyd <[email protected]>
2018-12-03Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/ideLinus Torvalds2-13/+3
Pull IDE fixes from David Miller: "A missing of_node_put() and a small cleanup" * git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide: ide: Change to use DEFINE_SHOW_ATTRIBUTE macro ide: pmac: add of_node_put()
2018-12-03Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparcLinus Torvalds7-2/+8
Pull sparc fixes from David Miller: 1) Some implicit switch fallthrough fixes from Stephen Rothwell. 2) Missing of_node_put() in various sparc drivers from Yangtao Li. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc: drivers/tty: add missing of_node_put() drivers/sbus/char: add of_node_put() sbus: char: add of_node_put() sparc32: supress another implicit-fallthrough warning sparc32: suppress an implicit-fallthrough warning sparc: suppress the implicit-fallthrough warning arch/sparc: Use kzalloc_node
Powered by cgit, Gruvboxed by Blaster4385.