aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2020-02-11net: ena: make ena rxfh support ETH_RSS_HASH_NO_CHANGEArthur Kiyanovski3-0/+16
As the name suggests ETH_RSS_HASH_NO_CHANGE is received upon changing the key or indirection table using ethtool while keeping the same hash function. Also add a function for retrieving the current hash function from the ena-com layer. Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Sameeh Jubran <[email protected]> Signed-off-by: Saeed Bshara <[email protected]> Signed-off-by: Arthur Kiyanovski <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-02-11net: ena: fix corruption of dev_idx_to_host_tblArthur Kiyanovski1-28/+0
The function ena_com_ind_tbl_convert_from_device() has an overflow bug as explained below. Either way, this function is not needed at all since we don't retrieve the indirection table from the device at any point which means that this conversion is not needed. The bug: The for loop iterates over all io_sq_queues, when passing the actual number of used queues the io_sq_queues[i].idx equals 0 since they are uninitialized which results in the following code to be executed till the end of the loop: dev_idx_to_host_tbl[0] = i; This results dev_idx_to_host_tbl[0] in being equal to ENA_TOTAL_NUM_QUEUES - 1. Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Sameeh Jubran <[email protected]> Signed-off-by: Arthur Kiyanovski <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-02-11net: ena: fix incorrectly saving queue numbers when setting RSS indirection ↵Arthur Kiyanovski2-1/+25
table The indirection table has the indices of the Rx queues. When we store it during set indirection operation, we convert the indices to our internal representation of the indices. Our internal representation of the indices is: even indices for Tx and uneven indices for Rx, where every Tx/Rx pair are in a consecutive order starting from 0. For example if the driver has 3 queues (3 for Tx and 3 for Rx) then the indices are as follows: 0 1 2 3 4 5 Tx Rx Tx Rx Tx Rx The BUG: The issue is that when we satisfy a get request for the indirection table, we don't convert the indices back to the original representation. The FIX: Simply apply the inverse function for the indices of the indirection table after we set it. Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Sameeh Jubran <[email protected]> Signed-off-by: Arthur Kiyanovski <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-02-11net: ena: rss: store hash function as values and not bitsArthur Kiyanovski1-1/+5
The device receives, stores and retrieves the hash function value as bits and not as their enum value. The bug: * In ena_com_set_hash_function() we set cmd.u.flow_hash_func.selected_func to the bit value of rss->hash_func. (1 << rss->hash_func) * In ena_com_get_hash_function() we retrieve the hash function and store it's bit value in rss->hash_func. (Now the bit value of rss->hash_func is stored in rss->hash_func instead of it's enum value) The fix: This commit fixes the issue by converting the retrieved hash function values from the device to the matching enum value of the set bit using ffs(). ffs() finds the first set bit's index in a word. Since the function returns 1 for the LSB's index, we need to subtract 1 from the returned value (note that BIT(0) is 1). Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Sameeh Jubran <[email protected]> Signed-off-by: Arthur Kiyanovski <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-02-11net: ena: rss: fix failure to get indirection tableSameeh Jubran1-0/+14
On old hardware, getting / setting the hash function is not supported while gettting / setting the indirection table is. This commit enables us to still show the indirection table on older hardwares by setting the hash function and key to NULL. Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Sameeh Jubran <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-02-11net: ena: rss: do not allocate key when not supportedSameeh Jubran1-3/+21
Currently we allocate the key whether the device supports setting the key or not. This commit adds a check to the allocation function and handles the error accordingly. Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Sameeh Jubran <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-02-11net: ena: fix incorrect default RSS keyArthur Kiyanovski2-0/+16
Bug description: When running "ethtool -x <if_name>" the key shows up as all zeros. When we use "ethtool -X <if_name> hfunc toeplitz hkey <some:random:key>" to set the key and then try to retrieve it using "ethtool -x <if_name>" then we return the correct key because we return the one we saved. Bug cause: We don't fetch the key from the device but instead return the key that we have saved internally which is by default set to zero upon allocation. Fix: This commit fixes the issue by initializing the key to a random value using netdev_rss_key_fill(). Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Sameeh Jubran <[email protected]> Signed-off-by: Arthur Kiyanovski <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-02-11net: ena: add missing ethtool TX timestamping indicationArthur Kiyanovski1-0/+1
Current implementation of the driver calls skb_tx_timestamp()to add a software tx timestamp to the skb, however the software-transmit capability is not reported in ethtool -T. This commit updates the ethtool structure to report the software-transmit capability in ethtool -T using the standard ethtool_op_get_ts_info(). This function reports all software timestamping capabilities (tx and rx), as well as setting phc_index = -1. phc_index is the index of the PTP hardware clock device that will be used for hardware timestamps. Since we don't have such a device in ENA, using the default -1 value is the correct setting. Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Ezequiel Lara Gomez <[email protected]> Signed-off-by: Arthur Kiyanovski <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-02-11net: ena: fix uses of round_jiffies()Arthur Kiyanovski1-3/+3
>From the documentation of round_jiffies(): "Rounds a time delta in the future (in jiffies) up or down to (approximately) full seconds. This is useful for timers for which the exact time they fire does not matter too much, as long as they fire approximately every X seconds. By rounding these timers to whole seconds, all such timers will fire at the same time, rather than at various times spread out. The goal of this is to have the CPU wake up less, which saves power." There are 2 parts to this patch: ================================ Part 1: ------- In our case we need timer_service to be called approximately every X=1 seconds, and the exact time does not matter, so using round_jiffies() is the right way to go. Therefore we add round_jiffies() to the mod_timer() in ena_timer_service(). Part 2: ------- round_jiffies() is used in check_for_missing_keep_alive() when getting the jiffies of the expiration of the keep_alive timeout. Here it is actually a mistake to use round_jiffies() because we want the exact time when keep_alive should expire and not an approximate rounded time, which can cause early, false positive, timeouts. Therefore we remove round_jiffies() in the calculation of keep_alive_expired() in check_for_missing_keep_alive(). Fixes: 82ef30f13be0 ("net: ena: add hardware hints capability to the driver") Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Arthur Kiyanovski <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-02-11net: ena: fix potential crash when rxfh key is NULLArthur Kiyanovski1-8/+9
When ethtool -X is called without an hkey, ena_com_fill_hash_function() is called with key=NULL, which is passed to memcpy causing a crash. This commit fixes this issue by checking key is not NULL. Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Sameeh Jubran <[email protected]> Signed-off-by: Arthur Kiyanovski <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-02-11net/smc: fix leak of kernel memory to user spaceEric Dumazet1-3/+2
As nlmsg_put() does not clear the memory that is reserved, it this the caller responsability to make sure all of this memory will be written, in order to not reveal prior content. While we are at it, we can provide the socket cookie even if clsock is not set. syzbot reported : BUG: KMSAN: uninit-value in __arch_swab32 arch/x86/include/uapi/asm/swab.h:10 [inline] BUG: KMSAN: uninit-value in __fswab32 include/uapi/linux/swab.h:59 [inline] BUG: KMSAN: uninit-value in __swab32p include/uapi/linux/swab.h:179 [inline] BUG: KMSAN: uninit-value in __be32_to_cpup include/uapi/linux/byteorder/little_endian.h:82 [inline] BUG: KMSAN: uninit-value in get_unaligned_be32 include/linux/unaligned/access_ok.h:30 [inline] BUG: KMSAN: uninit-value in ____bpf_skb_load_helper_32 net/core/filter.c:240 [inline] BUG: KMSAN: uninit-value in ____bpf_skb_load_helper_32_no_cache net/core/filter.c:255 [inline] BUG: KMSAN: uninit-value in bpf_skb_load_helper_32_no_cache+0x14a/0x390 net/core/filter.c:252 CPU: 1 PID: 5262 Comm: syz-executor.5 Not tainted 5.5.0-rc5-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x1c9/0x220 lib/dump_stack.c:118 kmsan_report+0xf7/0x1e0 mm/kmsan/kmsan_report.c:118 __msan_warning+0x58/0xa0 mm/kmsan/kmsan_instr.c:215 __arch_swab32 arch/x86/include/uapi/asm/swab.h:10 [inline] __fswab32 include/uapi/linux/swab.h:59 [inline] __swab32p include/uapi/linux/swab.h:179 [inline] __be32_to_cpup include/uapi/linux/byteorder/little_endian.h:82 [inline] get_unaligned_be32 include/linux/unaligned/access_ok.h:30 [inline] ____bpf_skb_load_helper_32 net/core/filter.c:240 [inline] ____bpf_skb_load_helper_32_no_cache net/core/filter.c:255 [inline] bpf_skb_load_helper_32_no_cache+0x14a/0x390 net/core/filter.c:252 Uninit was created at: kmsan_save_stack_with_flags mm/kmsan/kmsan.c:144 [inline] kmsan_internal_poison_shadow+0x66/0xd0 mm/kmsan/kmsan.c:127 kmsan_kmalloc_large+0x73/0xc0 mm/kmsan/kmsan_hooks.c:128 kmalloc_large_node_hook mm/slub.c:1406 [inline] kmalloc_large_node+0x282/0x2c0 mm/slub.c:3841 __kmalloc_node_track_caller+0x44b/0x1200 mm/slub.c:4368 __kmalloc_reserve net/core/skbuff.c:141 [inline] __alloc_skb+0x2fd/0xac0 net/core/skbuff.c:209 alloc_skb include/linux/skbuff.h:1049 [inline] netlink_dump+0x44b/0x1ab0 net/netlink/af_netlink.c:2224 __netlink_dump_start+0xbb2/0xcf0 net/netlink/af_netlink.c:2352 netlink_dump_start include/linux/netlink.h:233 [inline] smc_diag_handler_dump+0x2ba/0x300 net/smc/smc_diag.c:242 sock_diag_rcv_msg+0x211/0x610 net/core/sock_diag.c:256 netlink_rcv_skb+0x451/0x650 net/netlink/af_netlink.c:2477 sock_diag_rcv+0x63/0x80 net/core/sock_diag.c:275 netlink_unicast_kernel net/netlink/af_netlink.c:1302 [inline] netlink_unicast+0xf9e/0x1100 net/netlink/af_netlink.c:1328 netlink_sendmsg+0x1248/0x14d0 net/netlink/af_netlink.c:1917 sock_sendmsg_nosec net/socket.c:639 [inline] sock_sendmsg net/socket.c:659 [inline] kernel_sendmsg+0x433/0x440 net/socket.c:679 sock_no_sendpage+0x235/0x300 net/core/sock.c:2740 kernel_sendpage net/socket.c:3776 [inline] sock_sendpage+0x1e1/0x2c0 net/socket.c:937 pipe_to_sendpage+0x38c/0x4c0 fs/splice.c:458 splice_from_pipe_feed fs/splice.c:512 [inline] __splice_from_pipe+0x539/0xed0 fs/splice.c:636 splice_from_pipe fs/splice.c:671 [inline] generic_splice_sendpage+0x1d5/0x2d0 fs/splice.c:844 do_splice_from fs/splice.c:863 [inline] do_splice fs/splice.c:1170 [inline] __do_sys_splice fs/splice.c:1447 [inline] __se_sys_splice+0x2380/0x3350 fs/splice.c:1427 __x64_sys_splice+0x6e/0x90 fs/splice.c:1427 do_syscall_64+0xb8/0x160 arch/x86/entry/common.c:296 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Fixes: f16a7dd5cf27 ("smc: netlink interface for SMC sockets") Signed-off-by: Eric Dumazet <[email protected]> Cc: Ursula Braun <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-02-11i40e: Fix the conditional for i40e_vc_validate_vqs_bitmapsBrett Creeley1-2/+2
Commit d9d6a9aed3f6 ("i40e: Fix virtchnl_queue_select bitmap validation") introduced a necessary change for verifying how queue bitmaps from the iavf driver get validated. Unfortunately, the conditional was reversed. Fix this. Fixes: d9d6a9aed3f6 ("i40e: Fix virtchnl_queue_select bitmap validation") Signed-off-by: Brett Creeley <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-02-11core: Don't skip generic XDP program execution for cloned SKBsToke Høiland-Jørgensen1-2/+2
The current generic XDP handler skips execution of XDP programs entirely if an SKB is marked as cloned. This leads to some surprising behaviour, as packets can end up being cloned in various ways, which will make an XDP program not see all the traffic on an interface. This was discovered by a simple test case where an XDP program that always returns XDP_DROP is installed on a veth device. When combining this with the Scapy packet sniffer (which uses an AF_PACKET) socket on the sending side, SKBs reliably end up in the cloned state, causing them to be passed through to the receiving interface instead of being dropped. A minimal reproducer script for this is included below. This patch fixed the issue by simply triggering the existing linearisation code for cloned SKBs instead of skipping the XDP program execution. This behaviour is in line with the behaviour of the native XDP implementation for the veth driver, which will reallocate and copy the SKB data if the SKB is marked as shared. Reproducer Python script (requires BCC and Scapy): from scapy.all import TCP, IP, Ether, sendp, sniff, AsyncSniffer, Raw, UDP from bcc import BPF import time, sys, subprocess, shlex SKB_MODE = (1 << 1) DRV_MODE = (1 << 2) PYTHON=sys.executable def client(): time.sleep(2) # Sniffing on the sender causes skb_cloned() to be set s = AsyncSniffer() s.start() for p in range(10): sendp(Ether(dst="aa:aa:aa:aa:aa:aa", src="cc:cc:cc:cc:cc:cc")/IP()/UDP()/Raw("Test"), verbose=False) time.sleep(0.1) s.stop() return 0 def server(mode): prog = BPF(text="int dummy_drop(struct xdp_md *ctx) {return XDP_DROP;}") func = prog.load_func("dummy_drop", BPF.XDP) prog.attach_xdp("a_to_b", func, mode) time.sleep(1) s = sniff(iface="a_to_b", count=10, timeout=15) if len(s): print(f"Got {len(s)} packets - should have gotten 0") return 1 else: print("Got no packets - as expected") return 0 if len(sys.argv) < 2: print(f"Usage: {sys.argv[0]} <skb|drv>") sys.exit(1) if sys.argv[1] == "client": sys.exit(client()) elif sys.argv[1] == "server": mode = SKB_MODE if sys.argv[2] == 'skb' else DRV_MODE sys.exit(server(mode)) else: try: mode = sys.argv[1] if mode not in ('skb', 'drv'): print(f"Usage: {sys.argv[0]} <skb|drv>") sys.exit(1) print(f"Running in {mode} mode") for cmd in [ 'ip netns add netns_a', 'ip netns add netns_b', 'ip -n netns_a link add a_to_b type veth peer name b_to_a netns netns_b', # Disable ipv6 to make sure there's no address autoconf traffic 'ip netns exec netns_a sysctl -qw net.ipv6.conf.a_to_b.disable_ipv6=1', 'ip netns exec netns_b sysctl -qw net.ipv6.conf.b_to_a.disable_ipv6=1', 'ip -n netns_a link set dev a_to_b address aa:aa:aa:aa:aa:aa', 'ip -n netns_b link set dev b_to_a address cc:cc:cc:cc:cc:cc', 'ip -n netns_a link set dev a_to_b up', 'ip -n netns_b link set dev b_to_a up']: subprocess.check_call(shlex.split(cmd)) server = subprocess.Popen(shlex.split(f"ip netns exec netns_a {PYTHON} {sys.argv[0]} server {mode}")) client = subprocess.Popen(shlex.split(f"ip netns exec netns_b {PYTHON} {sys.argv[0]} client")) client.wait() server.wait() sys.exit(server.returncode) finally: subprocess.run(shlex.split("ip netns delete netns_a")) subprocess.run(shlex.split("ip netns delete netns_b")) Fixes: d445516966dc ("net: xdp: support xdp generic on virtual devices") Reported-by: Stepan Horacek <[email protected]> Suggested-by: Paolo Abeni <[email protected]> Signed-off-by: Toke Høiland-Jørgensen <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-02-11Merge tag 'dax-fixes-5.6-rc1' of ↵Linus Torvalds6-24/+12
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm Pull dax fixes from Dan Williams: "A fix for an xfstest failure and some and an update that removes an fsdax dependency on block devices. Summary: - Fix RWF_NOWAIT writes to properly return -EAGAIN - Clean up an unused helper - Update dax_writeback_mapping_range to not need a block_device argument" * tag 'dax-fixes-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: dax: pass NOWAIT flag to iomap_apply dax: Get rid of fs_dax_get_by_host() helper dax: Pass dax_dev instead of bdev to dax_writeback_mapping_range()
2020-02-11Merge tag 'trace-v5.6-rc1' of ↵Linus Torvalds12-173/+167
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace Pull tracing fixes from Steven Rostedt: "Various fixes: - Fix an uninitialized variable - Fix compile bug to bootconfig userspace tool (in tools directory) - Suppress some error messages of bootconfig userspace tool - Remove unneded CONFIG_LIBXBC from bootconfig - Allocate bootconfig xbc_nodes dynamically. To ease complaints about taking up static memory at boot up - Use of parse_args() to parse bootconfig instead of strstr() usage Prevents issues of double quotes containing the interested string - Fix missing ring_buffer_nest_end() on synthetic event error path - Return zero not -EINVAL on soft disabled synthetic event (soft disabling must be the same as hard disabling, which returns zero) - Consolidate synthetic event code (remove duplicate code)" * tag 'trace-v5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: tracing: Consolidate trace() functions tracing: Don't return -EINVAL when tracing soft disabled synth events tracing: Add missing nest end to synth_event_trace_start() error case tools/bootconfig: Suppress non-error messages bootconfig: Allocate xbc_nodes array dynamically bootconfig: Use parse_args() to find bootconfig and '--' tracing/kprobe: Fix uninitialized variable bug bootconfig: Remove unneeded CONFIG_LIBXBC tools/bootconfig: Fix wrong __VA_ARGS__ usage
2020-02-11ACPI: PM: s2idle: Prevent spurious SCIs from waking up the systemRafael J. Wysocki1-3/+9
If the platform triggers a spurious SCI even though the status bit is not set for any GPE when the system is suspended to idle, it will be treated as a genuine wakeup, so avoid that by checking if any GPEs are active at all before returning 'true' from acpi_s2idle_wake(). Link: https://bugzilla.kernel.org/show_bug.cgi?id=206413 Fixes: 56b991849009 ("PM: sleep: Simplify suspend-to-idle control flow") Reported-by: Tsuchiya Yuto <[email protected]> Cc: 5.4+ <[email protected]> # 5.4+ Signed-off-by: Rafael J. Wysocki <[email protected]>
2020-02-11ACPICA: Introduce acpi_any_gpe_status_set()Rafael J. Wysocki4-0/+106
Introduce a new helper function, acpi_any_gpe_status_set(), for checking the status bits of all enabled GPEs in one go. It is needed to distinguish spurious SCIs from genuine ones when deciding whether or not to wake up the system from suspend-to-idle. Cc: 5.4+ <[email protected]> # 5.4+ Signed-off-by: Rafael J. Wysocki <[email protected]>
2020-02-11drm/amdgpu:/navi10: use the ODCAP enum to index the caps arrayAlex Deucher1-11/+11
Rather than the FEATURE_ID flags. Avoids a possible reading past the end of the array. Reviewed-by: Evan Quan <[email protected]> Reported-by: Aleksandr Mezin <[email protected]> Signed-off-by: Alex Deucher <[email protected]> Cc: [email protected] # 5.5.x
2020-02-11drm/amdgpu: update smu_v11_0_pptable.hAlex Deucher1-14/+32
Update to the latest changes. Reviewed-by: Evan Quan <[email protected]> Signed-off-by: Alex Deucher <[email protected]> Cc: [email protected] # 5.5.x
2020-02-11drm/amdgpu: correct comment to clear up the confusionGuchun Chen1-1/+6
Former comment looks to be one intended behavior in code, actually it's not. So correct it. Suggested-by: Christian König <[email protected]> Signed-off-by: Guchun Chen <[email protected]> Acked-by: Christian König <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2020-02-11drm/amd/display: DCN2.x Do not program DPPCLK if same valueSung Lee1-1/+1
[WHY] Programming DPPCLK to the same value currently set may cause underflow while playing video in certain conditions. [HOW] Only program DPPCLK if clock is not the same as the previous value programmed. Signed-off-by: Sung Lee <[email protected]> Reviewed-by: Yongqiang Sun <[email protected]> Acked-by: Rodrigo Siqueira <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2020-02-11drm/amd/display: Don't map ATOM_ENABLE to ATOM_INITNicholas Kazlauskas1-4/+0
[Why] In DCN hardware sequencer we do actually call ATOM_INIT correctly per pipe. The workaround is not necessary for command table offloading. [How] Drop the workaround since it's not needed. Signed-off-by: Nicholas Kazlauskas <[email protected]> Reviewed-by: Chris Park <[email protected]> Acked-by: Rodrigo Siqueira <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2020-02-11drm/amdgpu/vcn2.5: fix warningJames Zhu1-1/+1
Fix warning during switching to dpg pause mode for VCN firmware Version ENC: 1.1 DEC: 1 VEP: 0 Revision: 16 Signed-off-by: James Zhu <[email protected]> Acked-by: Leo Liu <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2020-02-11drm/amdgpu: limit GDS clearing workaround in cold boot sequenceGuchun Chen1-3/+6
GDS clear workaround will cause gfx failure in suspend/resume case. [ 98.679559] [drm:amdgpu_device_ip_late_init [amdgpu]] *ERROR* late_init of IP block <gfx_v9_0> failed -110 [ 98.679561] PM: dpm_run_callback(): pci_pm_resume+0x0/0xa0 returns -110 [ 98.679562] PM: Device 0000:03:00.0 failed to resume async: error -110 As this workaround is specific to the HW bug of GDS's ECC error existing in cold boot up, so bypass this workaround in suspend/ resume case after booting up. Signed-off-by: Guchun Chen <[email protected]> Reviewed-by: Hawking Zhang <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2020-02-11drm/amdgpu: fix amdgpu pmu to use hwc->config instead of hwc->confJonathan Kim1-7/+8
hwc->conf was designated specifically for AMD APU IOMMU purposes. This could cause problems in performance and/or function since APU IOMMU implementation is elsewhere. Also hwc->conf and hwc->config are different members of an anonymous union so hwc->conf aliases as hw->last_tag. Signed-off-by: Jonathan Kim <[email protected]> Reviewed-by: Felix Kuehling <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2020-02-11amdgpu: Prevent build errors regarding soft/hard-float FP ABI tagsDaniel Kolesa1-0/+6
On PowerPC, the compiler will tag object files with whether they use hard or soft float FP ABI and whether they use 64 or 128-bit long double ABI. On systems with 64-bit long double ABI, a tag will get emitted whenever a double is used, as on those systems a long double is the same as a double. This will prevent linkage as other files are being compiled with hard-float. On ppc64, this code will never actually get used for the time being, as the only currently existing hardware using it are the Renoir APUs. Therefore, until this is testable and can be fixed properly, at least make sure the build will not fail. Signed-off-by: Daniel Kolesa <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2020-02-11drm/amdgpu/vcn2.5: fix DPG mode power off issue on instance 1James Zhu4-14/+15
Support pause_state for multiple instance, and it will fix vcn2.5 DPG mode power off issue on instance 1. Signed-off-by: James Zhu <[email protected]> Reviewed-by: Leo Liu <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2020-02-11drm/amd/display: Add initialitions for PLL2 clock sourceIsabel Zhang1-0/+6
[Why] Starting from 14nm, the PLL is built into the PHY and the PLL is mapped to PHY on 1 to 1 basis. In the code, the DP port is mapped to a PLL that was not initialized. This causes DP to HDMI dongle to not light up the display. [How] Initializations added for PLL2 when creating resources. Signed-off-by: Isabel Zhang <[email protected]> Reviewed-by: Eric Yang <[email protected]> Acked-by: Bhawanpreet Lakha <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2020-02-11drm/amd/display: Limit minimum DPPCLK to 100MHz.Yongqiang Sun1-0/+6
[Why] Underflow is observed when plug in a 4K@60 monitor with 1366x768 eDP due to DPPCLK is too low. [How] Limit minimum DPPCLK to 100MHz. Signed-off-by: Yongqiang Sun <[email protected]> Reviewed-by: Eric Yang <[email protected]> Acked-by: Bhawanpreet Lakha <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2020-02-11drm/amd/display: Check engine is not NULL before acquiringAric Cyr1-1/+1
[Why] Engine can be NULL in some cases, so we must not acquire it. [How] Check for NULL engine before acquiring. Signed-off-by: Aric Cyr <[email protected]> Reviewed-by: Harry Wentland <[email protected]> Acked-by: Bhawanpreet Lakha <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2020-02-11tools headers UAPI: Sync sched.h with the kernelArnaldo Carvalho de Melo1-0/+6
To get the changes in: 769071ac9f20 ("ns: Introduce Time Namespace") Silencing this tools/perf build warning: Warning: Kernel ABI header at 'tools/include/uapi/linux/sched.h' differs from latest version at 'include/uapi/linux/sched.h' diff -u tools/include/uapi/linux/sched.h include/uapi/linux/sched.h Which enables 'perf trace' to decode the CLONE_NEWTIME bit in the 'flags' argument to the clone syscalls. Example of clone flags being decoded: [root@quaco ~]# perf trace -e clone* 0.000 qemu-system-x8/23923 clone(clone_flags: VM|FS|FILES|SIGHAND|THREAD|SYSVSEM|SETTLS|PARENT_SETTID|CHILD_CLEARTID, newsp: 0x7f0dad7f9870, parent_tidptr: 0x7f0dad7fa9d0, child_tidptr: 0x7f0dad7fa9d0, tls: 0x7f0dad7fa700) = 6806 (qemu-system-x86) ? qemu-system-x8/6806 ... [continued]: clone()) = 0 ^C[root@quaco ~]# At some point this should enable things like: # perf trace -e 'clone*/clone_flags&NEWTIME/' Cc: Adrian Hunter <[email protected]> Cc: Andrei Vagin <[email protected]> Cc: Jiri Olsa <[email protected]> Cc: Namhyung Kim <[email protected]> Cc: Thomas Gleixner <[email protected]> Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
2020-02-11perf trace: Resolve prctl's 'option' arg strings to numbersArnaldo Carvalho de Melo1-1/+3
# perf trace -e syscalls:sys_enter_prctl --filter="option==SET_NAME" 0.000 Socket Thread/3860 syscalls:sys_enter_prctl(option: SET_NAME, arg2: 0x7fc50b9733e8) 0.053 SSL Cert #78/3860 syscalls:sys_enter_prctl(option: SET_NAME, arg2: 0x7fc50b9733e8) ^C # If one uses '-v' with 'perf trace', we can see the filter it puts in place: New filter for syscalls:sys_enter_prctl: (option==0xf) && (common_pid != 3859 && common_pid != 2757) We still need to allow using plain '-e prctl' and have this turn into creating a 'syscalls:sys_enter_prctl' event so that the filter can be applied only to it as right now '-e prctl' ends up using the 'raw_syscalls:sys_enter/sys_exit'. The end goal is to have something like: # perf trace -e prctl/option==SET_NAME/ And have that use tracepoint filters or eBPF ones. Cc: Adrian Hunter <[email protected]> Cc: Christian Brauner <[email protected]> Cc: Jiri Olsa <[email protected]> Cc: Mike Christie <[email protected]> Cc: Namhyung Kim <[email protected]> Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
2020-02-11perf beauty prctl: Export the 'options' strarrayArnaldo Carvalho de Melo2-1/+4
So that we can use it with strtoul, allowing string to number conversions in filter expressions. Cc: Adrian Hunter <[email protected]> Cc: Christian Brauner <[email protected]> Cc: Jiri Olsa <[email protected]> Cc: Mike Christie <[email protected]> Cc: Namhyung Kim <[email protected]> Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
2020-02-11tools headers UAPI: Sync prctl.h with the kernel sourcesArnaldo Carvalho de Melo1-0/+4
To get the changes in: 8d19f1c8e193 ("prctl: PR_{G,S}ET_IO_FLUSHER to support controlling memory reclaim") Which ends up having this effect in tooling, i.e. the addition of the support to those prctl's options: $ tools/perf/trace/beauty/prctl_option.sh > before $ cp include/uapi/linux/prctl.h tools/include/uapi/linux/prctl.h $ git diff diff --git a/tools/include/uapi/linux/prctl.h b/tools/include/uapi/linux/prctl.h index 7da1b37b27aa..07b4f8131e36 100644 --- a/tools/include/uapi/linux/prctl.h +++ b/tools/include/uapi/linux/prctl.h @@ -234,4 +234,8 @@ struct prctl_mm_map { #define PR_GET_TAGGED_ADDR_CTRL 56 # define PR_TAGGED_ADDR_ENABLE (1UL << 0) +/* Control reclaim behavior when allocating memory */ +#define PR_SET_IO_FLUSHER 57 +#define PR_GET_IO_FLUSHER 58 + #endif /* _LINUX_PRCTL_H */ $ tools/perf/trace/beauty/prctl_option.sh > after $ diff -u before after --- before 2020-02-11 15:24:35.339289912 -0300 +++ after 2020-02-11 15:24:56.319711315 -0300 @@ -51,6 +51,8 @@ [54] = "PAC_RESET_KEYS", [55] = "SET_TAGGED_ADDR_CTRL", [56] = "GET_TAGGED_ADDR_CTRL", + [57] = "SET_IO_FLUSHER", + [58] = "GET_IO_FLUSHER", }; static const char *prctl_set_mm_options[] = { [1] = "START_CODE", $ Cc: Adrian Hunter <[email protected]> Cc: Christian Brauner <[email protected]> Cc: Jiri Olsa <[email protected]> Cc: Mike Christie <[email protected]> Cc: Namhyung Kim <[email protected]> Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
2020-02-11tools headers UAPI: Sync copy of arm64's asm/unistd.h with the kernel sourcesArnaldo Carvalho de Melo1-0/+1
To get the changes in: 3e3c8ca5a351 ("arm64: Move __ARCH_WANT_SYS_CLONE3 definition to uapi headers") Silencing this tools/perf/ build warning: Warning: Kernel ABI header at 'tools/arch/arm64/include/uapi/asm/unistd.h' differs from latest version at 'arch/arm64/include/uapi/asm/unistd.h' diff -u tools/arch/arm64/include/uapi/asm/unistd.h arch/arm64/include/uapi/asm/unistd.h Which will probably end up enabling the use of "clone3" in 'perf trace -e', haven't checked the build with this change on an arm64 system. Cc: Adrian Hunter <[email protected]> Cc: Amanieu d'Antras <[email protected]> Cc: Christian Brauner <[email protected]> Cc: Jiri Olsa <[email protected]> Cc: Namhyung Kim <[email protected]> Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
2020-02-11perf maps: Move kmap::kmaps setup to maps__insert()Jiri Olsa2-12/+11
So the kmaps pointer setup is centralized and we do not need to update it in all those places (2 current places and few more missing) after calling maps__insert(). Reported-by: Ravi Bangoria <[email protected]> Signed-off-by: Jiri Olsa <[email protected]> Tested-by: Ravi Bangoria <[email protected]> Tested-by: Kim Phillips <[email protected]> Cc: Alexander Shishkin <[email protected]> Cc: Michael Petlan <[email protected]> Cc: Namhyung Kim <[email protected]> Cc: Peter Zijlstra <[email protected]> Link: http://lore.kernel.org/lkml/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
2020-02-11perf maps: Fix map__clone() for struct kmapJiri Olsa1-1/+6
The map__clone() function can be called on kernel maps as well, so it needs to duplicate the whole kmap data. Reported-by: Ravi Bangoria <[email protected]> Signed-off-by: Jiri Olsa <[email protected]> Tested-by: Ravi Bangoria <[email protected]> Tested-by: Kim Phillips <[email protected]> Cc: Alexander Shishkin <[email protected]> Cc: Michael Petlan <[email protected]> Cc: Namhyung Kim <[email protected]> Cc: Peter Zijlstra <[email protected]> Link: http://lore.kernel.org/lkml/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
2020-02-11perf maps: Mark ksymbol DSOs with kernel typeJiri Olsa1-2/+10
We add ksymbol map into machine->kmaps, so it needs to be created as 'struct kmap', which is dependent on its dso having kernel type. Reported-by: Ravi Bangoria <[email protected]> Signed-off-by: Jiri Olsa <[email protected]> Tested-by: Ravi Bangoria <[email protected]> Tested-by: Kim Phillips <[email protected]> Cc: Alexander Shishkin <[email protected]> Cc: Michael Petlan <[email protected]> Cc: Namhyung Kim <[email protected]> Cc: Peter Zijlstra <[email protected]> Link: http://lore.kernel.org/lkml/20200210200847.GA36715@krava Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
2020-02-11perf maps: Mark module DSOs with kernel typeJiri Olsa1-0/+1
We add kernel module map into machine->kmaps, so it needs to be created as 'struct kmap', which is dependent on its dso having kernel type. Reported-by: Ravi Bangoria <[email protected]> Signed-off-by: Jiri Olsa <[email protected]> Tested-by: Kim Phillips <[email protected]> Tested-by: Ravi Bangoria <[email protected]> Cc: Alexander Shishkin <[email protected]> Cc: Michael Petlan <[email protected]> Cc: Namhyung Kim <[email protected]> Cc: Peter Zijlstra <[email protected]> Link: http://lore.kernel.org/lkml/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
2020-02-11tools include UAPI: Sync x86's syscalls_64.tbl, generic unistd.h and fcntl.h ↵Arnaldo Carvalho de Melo5-2/+49
to pick up openat2 and pidfd_getfd fddb5d430ad9 ("open: introduce openat2(2) syscall") 9a2cef09c801 ("arch: wire up pidfd_getfd syscall") We also need to grab a copy of uapi/linux/openat2.h since it is now needed by fcntl.h, add it to tools/perf/check_headers.h. $ diff -u tools/perf/arch/x86/entry/syscalls/syscall_64.tbl arch/x86/entry/syscalls/syscall_64.tbl --- tools/perf/arch/x86/entry/syscalls/syscall_64.tbl 2019-12-20 16:43:57.662429958 -0300 +++ arch/x86/entry/syscalls/syscall_64.tbl 2020-02-10 16:36:22.070012468 -0300 @@ -357,6 +357,8 @@ 433 common fspick __x64_sys_fspick 434 common pidfd_open __x64_sys_pidfd_open 435 common clone3 __x64_sys_clone3/ptregs +437 common openat2 __x64_sys_openat2 +438 common pidfd_getfd __x64_sys_pidfd_getfd # # x32-specific system call numbers start at 512 to avoid cache impact $ Update tools/'s copy of that file: $ cp arch/x86/entry/syscalls/syscall_64.tbl tools/perf/arch/x86/entry/syscalls/syscall_64.tbl See the result: $ diff -u /tmp/build/perf/arch/x86/include/generated/asm/syscalls_64.c.before /tmp/build/perf/arch/x86/include/generated/asm/syscalls_64.c --- /tmp/build/perf/arch/x86/include/generated/asm/syscalls_64.c.before 2020-02-10 16:42:59.010636041 -0300 +++ /tmp/build/perf/arch/x86/include/generated/asm/syscalls_64.c 2020-02-10 16:43:24.149958337 -0300 @@ -346,5 +346,7 @@ [433] = "fspick", [434] = "pidfd_open", [435] = "clone3", + [437] = "openat2", + [438] = "pidfd_getfd", }; -#define SYSCALLTBL_x86_64_MAX_ID 435 +#define SYSCALLTBL_x86_64_MAX_ID 438 $ Now one can use: perf trace -e openat2,pidfd_getfd To get just those syscalls or use in things like: perf trace -e open* To get all the open variant (open, openat, openat2, etc) or: perf trace pidfd* To get the pidfd syscalls. Cc: Adrian Hunter <[email protected]> Cc: Aleksa Sarai <[email protected]> Cc: Al Viro <[email protected]> Cc: Christian Brauner <[email protected]> Cc: Jiri Olsa <[email protected]> Cc: Namhyung Kim <[email protected]> Cc: Sargun Dhillon <[email protected]> Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
2020-02-11ALSA: usb-audio: Apply sample rate quirk for Audioengine D1Arvind Sankar1-0/+1
The Audioengine D1 (0x2912:0x30c8) does support reading the sample rate, but it returns the rate in byte-reversed order. When setting sampling rate, the driver produces these warning messages: [168840.944226] usb 3-2.2: current rate 4500480 is different from the runtime rate 44100 [168854.930414] usb 3-2.2: current rate 8436480 is different from the runtime rate 48000 [168905.185825] usb 3-2.1.2: current rate 30465 is different from the runtime rate 96000 As can be seen from the hexadecimal conversion, the current rate read back is byte-reversed from the rate that was set. 44100 == 0x00ac44, 4500480 == 0x44ac00 48000 == 0x00bb80, 8436480 == 0x80bb00 96000 == 0x017700, 30465 == 0x007701 Rather than implementing a new quirk to reverse the order, just skip checking the rate to avoid spamming the log. Signed-off-by: Arvind Sankar <[email protected]> Cc: <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Takashi Iwai <[email protected]>
2020-02-11drm/amd/display: Use dcfclk to populate watermark rangesSung Lee1-7/+7
[WHY & HOW] Previously drain clk was unconstrained and fill clk was constrained on fclk. We want to change it to fill clk unconstrained and drain clock constrained to dcfclk. Signed-off-by: Sung Lee <[email protected]> Reviewed-by: Tony Cheng <[email protected]> Acked-by: Bhawanpreet Lakha <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2020-02-11drm/amd/display: Do not set optimized_require to false after plane disableSung Lee1-1/+0
[WHY] The optimized_require flag is needed to set watermarks and clocks lower in certain conditions. This flag is set to true and then set to false while programming front end in dcn20. [HOW] Do not set the flag to false while disabling plane. Signed-off-by: Sung Lee <[email protected]> Reviewed-by: Tony Cheng <[email protected]> Acked-by: Bhawanpreet Lakha <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2020-02-11drm/amd/display: Fix psr static frames calculationRoman Li1-2/+3
[Why] Driver crash with psr feature enabled due to divide-by-zero error. This is a regression after rework to calculate static screen frame number entry time. [How] Correct order of operations to avoid divide-by-zero. Signed-off-by: Roman Li <[email protected]> Reviewed-by: Zhan Liu <[email protected]> Acked-by: Bhawanpreet Lakha <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2020-02-11ALSA: usb-audio: Fix UAC2/3 effect unit parsingTakashi Iwai1-2/+10
We've got a regression report about M-Audio Fast Track C400 device, and the git bisection resulted in the commit e0ccdef92653 ("ALSA: usb-audio: Clean up check_input_term()"). This commit was about the rewrite of the input terminal parser, and it's not too obvious from the change what really broke. The answer is: it's the interpretation of UAC2/3 effect units. In the original code, UAC2 effect unit is as if through UAC1 processing unit because both UAC1 PU and UAC2/3 EU share the same number (0x07). The old code went through a complex switch-case fallthrough, finally bailing out in the middle: if (protocol == UAC_VERSION_2 && hdr[2] == UAC2_EFFECT_UNIT) { /* UAC2/UAC1 unit IDs overlap here in an * uncompatible way. Ignore this unit for now. */ return 0; } ... and this special handling was missing in the new code; the new code treats UAC2/3 effect unit as if it were equivalent with the processing unit. Actually, the old code was too confusing. The effect unit has an incompatible unit description with the processing unit, so we shouldn't have dealt with EU in the same way. This patch addresses the regression by changing the effect unit handling to the own parser function. The own parser function makes the clear distinct with PU, so it improves the readability, too. The EU parser just sets the type and the id like the old kernels. Once when the proper effect unit support is added, we can revisit this parser function, but for now, let's keep this simple setup as is. Fixes: e0ccdef92653 ("ALSA: usb-audio: Clean up check_input_term()") Cc: <[email protected]> BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=206147 Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Takashi Iwai <[email protected]>
2020-02-11ceph: noacl mount option is effectively ignoredXiubo Li1-4/+4
For the old mount API, the module parameters parseing function will be called in ceph_mount() and also just after the default posix acl flag set, so we can control to enable/disable it via the mount option. But for the new mount API, it will call the module parameters parseing function before ceph_get_tree(), so the posix acl will always be enabled. Fixes: 82995cc6c5ae ("libceph, rbd, ceph: convert to use the new mount API") Signed-off-by: Xiubo Li <[email protected]> Reviewed-by: Ilya Dryomov <[email protected]> Signed-off-by: Ilya Dryomov <[email protected]>
2020-02-11ceph: canonicalize server path in placeIlya Dryomov2-94/+29
syzbot reported that 4fbc0c711b24 ("ceph: remove the extra slashes in the server path") had caused a regression where an allocation could be done under a spinlock -- compare_mount_options() is called by sget_fc() with sb_lock held. We don't really need the supplied server path, so canonicalize it in place and compare it directly. To make this work, the leading slash is kept around and the logic in ceph_real_mount() to skip it is restored. CEPH_MSG_CLIENT_SESSION now reports the same (i.e. canonicalized) path, with the leading slash of course. Fixes: 4fbc0c711b24 ("ceph: remove the extra slashes in the server path") Reported-by: [email protected] Signed-off-by: Ilya Dryomov <[email protected]> Reviewed-by: Jeff Layton <[email protected]>
2020-02-11ceph: do not execute direct write in parallel if O_APPEND is specifiedXiubo Li1-6/+11
In O_APPEND & O_DIRECT mode, the data from different writers will be possibly overlapping each other since they take the shared lock. For example, both Writer1 and Writer2 are in O_APPEND and O_DIRECT mode: Writer1 Writer2 shared_lock() shared_lock() getattr(CAP_SIZE) getattr(CAP_SIZE) iocb->ki_pos = EOF iocb->ki_pos = EOF write(data1) write(data2) shared_unlock() shared_unlock() The data2 will overlap the data1 from the same file offset, the old EOF. Switch to exclusive lock instead when O_APPEND is specified. Signed-off-by: Xiubo Li <[email protected]> Reviewed-by: Jeff Layton <[email protected]> Signed-off-by: Ilya Dryomov <[email protected]>
2020-02-11perf/x86/intel: Fix inaccurate period in context switch for auto-reloadKan Liang1-0/+2
Perf doesn't take the left period into account when auto-reload is enabled with fixed period sampling mode in context switch. Here is the MSR trace of the perf command as below. (The MSR trace is simplified from a ftrace log.) #perf record -e cycles:p -c 2000000 -- ./triad_loop //The MSR trace of task schedule out //perf disable all counters, disable PEBS, disable GP counter 0, //read GP counter 0, and re-enable all counters. //The counter 0 stops at 0xfffffff82840 write_msr: MSR_CORE_PERF_GLOBAL_CTRL(38f), value 0 write_msr: MSR_IA32_PEBS_ENABLE(3f1), value 0 write_msr: MSR_P6_EVNTSEL0(186), value 40003003c rdpmc: 0, value fffffff82840 write_msr: MSR_CORE_PERF_GLOBAL_CTRL(38f), value f000000ff //The MSR trace of the same task schedule in again //perf disable all counters, enable and set GP counter 0, //enable PEBS, and re-enable all counters. //0xffffffe17b80 (-2000000) is written to GP counter 0. write_msr: MSR_CORE_PERF_GLOBAL_CTRL(38f), value 0 write_msr: MSR_IA32_PMC0(4c1), value ffffffe17b80 write_msr: MSR_P6_EVNTSEL0(186), value 40043003c write_msr: MSR_IA32_PEBS_ENABLE(3f1), value 1 write_msr: MSR_CORE_PERF_GLOBAL_CTRL(38f), value f000000ff When the same task schedule in again, the counter should starts from previous left. However, it starts from the fixed period -2000000 again. A special variant of intel_pmu_save_and_restart() is used for auto-reload, which doesn't update the hwc->period_left. When the monitored task schedules in again, perf doesn't know the left period. The fixed period is used, which is inaccurate. With auto-reload, the counter always has a negative counter value. So the left period is -value. Update the period_left in intel_pmu_save_and_restart_reload(). With the patch: //The MSR trace of task schedule out write_msr: MSR_CORE_PERF_GLOBAL_CTRL(38f), value 0 write_msr: MSR_IA32_PEBS_ENABLE(3f1), value 0 write_msr: MSR_P6_EVNTSEL0(186), value 40003003c rdpmc: 0, value ffffffe25cbc write_msr: MSR_CORE_PERF_GLOBAL_CTRL(38f), value f000000ff //The MSR trace of the same task schedule in again write_msr: MSR_CORE_PERF_GLOBAL_CTRL(38f), value 0 write_msr: MSR_IA32_PMC0(4c1), value ffffffe25cbc write_msr: MSR_P6_EVNTSEL0(186), value 40043003c write_msr: MSR_IA32_PEBS_ENABLE(3f1), value 1 write_msr: MSR_CORE_PERF_GLOBAL_CTRL(38f), value f000000ff Fixes: d31fc13fdcb2 ("perf/x86/intel: Fix event update for auto-reload") Signed-off-by: Kan Liang <[email protected]> Signed-off-by: Peter Zijlstra (Intel) <[email protected]> Signed-off-by: Ingo Molnar <[email protected]> Link: https://lkml.kernel.org/r/[email protected]
2020-02-11perf/x86/amd: Add missing L2 misses event spec to AMD Family 17h's event mapKim Phillips1-0/+1
Commit 3fe3331bb285 ("perf/x86/amd: Add event map for AMD Family 17h"), claimed L2 misses were unsupported, due to them not being found in its referenced documentation, whose link has now moved [1]. That old documentation listed PMCx064 unit mask bit 3 as: "LsRdBlkC: LS Read Block C S L X Change to X Miss." and bit 0 as: "IcFillMiss: IC Fill Miss" We now have new public documentation [2] with improved descriptions, that clearly indicate what events those unit mask bits represent: Bit 3 now clearly states: "LsRdBlkC: Data Cache Req Miss in L2 (all types)" and bit 0 is: "IcFillMiss: Instruction Cache Req Miss in L2." So we can now add support for L2 misses in perf's genericised events as PMCx064 with both the above unit masks. [1] The commit's original documentation reference, "Processor Programming Reference (PPR) for AMD Family 17h Model 01h, Revision B1 Processors", originally available here: https://www.amd.com/system/files/TechDocs/54945_PPR_Family_17h_Models_00h-0Fh.pdf is now available here: https://developer.amd.com/wordpress/media/2017/11/54945_PPR_Family_17h_Models_00h-0Fh.pdf [2] "Processor Programming Reference (PPR) for Family 17h Model 31h, Revision B0 Processors", available here: https://developer.amd.com/wp-content/resources/55803_0.54-PUB.pdf Fixes: 3fe3331bb285 ("perf/x86/amd: Add event map for AMD Family 17h") Reported-by: Babu Moger <[email protected]> Signed-off-by: Kim Phillips <[email protected]> Signed-off-by: Peter Zijlstra (Intel) <[email protected]> Signed-off-by: Ingo Molnar <[email protected]> Tested-by: Babu Moger <[email protected]> Cc: [email protected] Link: https://lkml.kernel.org/r/[email protected]