aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2021-12-03io-wq: don't retry task_work creation failure on fatal conditionsJens Axboe1-0/+7
We don't want to be retrying task_work creation failure if there's an actual signal pending for the parent task. If we do, then we can enter an infinite loop of perpetually retrying and each retry failing with -ERESTARTNOINTR because a signal is pending. Fixes: 3146cba99aa2 ("io-wq: make worker creation resilient against signals") Reported-by: Florian Fischer <[email protected]> Link: https://lore.kernel.org/io-uring/20211202165606.mqryio4yzubl7ms5@pasture/ Tested-by: Florian Fischer <[email protected]> Signed-off-by: Jens Axboe <[email protected]>
2021-12-03nvmem: eeprom: at25: fix FRAM byte_lenRalph Siemsen1-20/+18
Commit fd307a4ad332 ("nvmem: prepare basics for FRAM support") added support for FRAM devices such as the Cypress FM25V. During testing, it was found that the FRAM detects properly, however reads and writes fail. Upon further investigation, two problem were found in at25_probe() routine. 1) In the case of an FRAM device without platform data, eg. fram == true && spi->dev.platform_data == NULL the stack local variable "struct spi_eeprom chip" is not initialized fully, prior to being copied into at25->chip. The chip.flags field in particular can cause problems. 2) The byte_len of FRAM is computed from its ID register, and is stored into the stack local "struct spi_eeprom chip" structure. This happens after the same structure has been copied into at25->chip. As a result, at25->chip.byte_len does not contain the correct length of the device. In turn this can cause checks at beginning of at25_ee_read() to fail (or equally, it could allow reads beyond the end of the device length). Fix both of these issues by eliminating the on-stack struct spi_eeprom. Instead use the one inside at25_data structure, which starts of zeroed. Fixes: fd307a4ad332 ("nvmem: prepare basics for FRAM support") Cc: stable <[email protected]> Reviewed-by: Arnd Bergmann <[email protected]> Signed-off-by: Ralph Siemsen <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-12-03misc: fastrpc: fix improper packet size calculationJeya R1-4/+6
The buffer list is sorted and this is not being considered while calculating packet size. This would lead to improper copy length calculation for non-dmaheap buffers which would eventually cause sending improper buffers to DSP. Fixes: c68cfb718c8f ("misc: fastrpc: Add support for context Invoke method") Reviewed-by: Srinivas Kandagatla <[email protected]> Signed-off-by: Jeya R <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-12-03MAINTAINERS: add maintainer for Qualcomm FastRPC driverSrinivas Kandagatla1-0/+9
For some reason I forgot to add myself as maintainer when we upstreamed FastRPC patches. Add myself and Amol from Qualcomm as maintainers for Qualcomm FastRPC driver. Signed-off-by: Srinivas Kandagatla <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-12-03serial: 8250_bcm7271: UART errors after resuming from S2Al Cooper1-0/+13
There is a small window in time during resume where the hardware flow control signal RTS can be asserted (which allows a sender to resume sending data to the UART) but the baud rate has not yet been restored. This will cause corrupted data and FRAMING, OVERRUN and BREAK errors. This is happening because the MCTRL register is shadowed in uart_port struct and is later used during resume to set the MCTRL register during both serial8250_do_startup() and uart_resume_port(). Unfortunately, serial8250_do_startup() happens before the UART baud rate is restored. The fix is to clear the shadowed mctrl value at the end of suspend and restore it at the end of resume. Fixes: 41a469482de2 ("serial: 8250: Add new 8250-core based Broadcom STB driver") Acked-by: Florian Fainelli <[email protected]> Signed-off-by: Al Cooper <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-12-03drm/ttm: fix ttm_bo_swapoutChristian König1-1/+2
Commit 7120a447c7fe ("drm/ttm: Double check mem_type of BO while eviction") made ttm_bo_evict_swapout_allowable() function actually check the placement, but we always used a dummy placement in ttm_bo_swapout. Fix this by using the real placement instead. Signed-off-by: Christian König <[email protected]> Fixes: 7120a447c7fe ("drm/ttm: Double check mem_type of BO while eviction") Reviewed-by: Pan, Xinhui <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
2021-12-03usb: cdnsp: Fix a NULL pointer dereference in cdnsp_endpoint_init()Zhou Qingyang1-0/+3
In cdnsp_endpoint_init(), cdnsp_ring_alloc() is assigned to pep->ring and there is a dereference of it in cdnsp_endpoint_init(), which could lead to a NULL pointer dereference on failure of cdnsp_ring_alloc(). Fix this bug by adding a check of pep->ring. This bug was found by a static analyzer. The analysis employs differential checking to identify inconsistent security operations (e.g., checks or kfrees) between two code paths and confirms that the inconsistent operations are not recovered in the current function or the callers, so they constitute bugs. Note that, as a bug found by static analysis, it can be a false positive or hard to trigger. Multiple researchers have cross-reviewed the bug. Builds with CONFIG_USB_CDNSP_GADGET=y show no new warnings, and our static analyzer no longer warns about this code. Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver") Cc: stable <[email protected]> Acked-by: Pawel Laszczak <[email protected]> Acked-by: Peter Chen <[email protected]> Signed-off-by: Zhou Qingyang <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-12-03usb: cdns3: gadget: fix new urb never complete if ep cancel previous requestsFrank Li1-16/+4
This issue was found at android12 MTP. 1. MTP submit many out urb request. 2. Cancel left requests (>20) when enough data get from host 3. Send ACK by IN endpoint. 4. MTP submit new out urb request. 5. 4's urb never complete. TRACE LOG: MtpServer-2157 [000] d..3 1287.150391: cdns3_ep_dequeue: ep1out: req: 00000000299e6836, req buff 000000009df42287, length: 0/16384 zsi, status: -115, trb: [start:87, end:87: virt addr 0x80004000ffd50420], flags:1 SID: 0 MtpServer-2157 [000] d..3 1287.150410: cdns3_gadget_giveback: ep1out: req: 00000000299e6836, req buff 000000009df42287, length: 0/16384 zsi, status: -104, trb: [start:87, end:87: virt addr 0x80004000ffd50420], flags:0 SID: 0 MtpServer-2157 [000] d..3 1287.150433: cdns3_ep_dequeue: ep1out: req: 0000000080b7bde6, req buff 000000009ed5c556, length: 0/16384 zsi, status: -115, trb: [start:88, end:88: virt addr 0x80004000ffd5042c], flags:1 SID: 0 MtpServer-2157 [000] d..3 1287.150446: cdns3_gadget_giveback: ep1out: req: 0000000080b7bde6, req buff 000000009ed5c556, length: 0/16384 zsi, status: -104, trb: [start:88, end:88: virt addr 0x80004000ffd5042c], flags:0 SID: 0 .... MtpServer-2157 [000] d..1 1293.630410: cdns3_alloc_request: ep1out: req: 00000000afbccb7d, req buff 0000000000000000, length: 0/0 zsi, status: 0, trb: [start:0, end:0: virt addr (null)], flags:0 SID: 0 MtpServer-2157 [000] d..2 1293.630421: cdns3_ep_queue: ep1out: req: 00000000afbccb7d, req buff 00000000871caf90, length: 0/512 zsi, status: -115, trb: [start:0, end:0: virt addr (null)], flags:0 SID: 0 MtpServer-2157 [000] d..2 1293.630445: cdns3_wa1: WA1: ep1out set guard MtpServer-2157 [000] d..2 1293.630450: cdns3_wa1: WA1: ep1out restore cycle bit MtpServer-2157 [000] d..2 1293.630453: cdns3_prepare_trb: ep1out: trb 000000007317b3ee, dma buf: 0xffd5bc00, size: 512, burst: 128 ctrl: 0x00000424 (C=0, T=0, ISP, IOC, Normal) SID:0 LAST_SID:0 MtpServer-2157 [000] d..2 1293.630460: cdns3_doorbell_epx: ep1out, ep_trbaddr ffd50414 .... irq/241-5b13000-2154 [000] d..1 1293.680849: cdns3_epx_irq: IRQ for ep1out: 01000408 ISP , ep_traddr: ffd508ac ep_last_sid: 00000000 use_streams: 0 irq/241-5b13000-2154 [000] d..1 1293.680858: cdns3_complete_trb: ep1out: trb 0000000021a11b54, dma buf: 0xffd50420, size: 16384, burst: 128 ctrl: 0x00001810 (C=0, T=0, CHAIN, LINK) SID:0 LAST_SID:0 irq/241-5b13000-2154 [000] d..1 1293.680865: cdns3_request_handled: Req: 00000000afbccb7d not handled, DMA pos: 185, ep deq: 88, ep enq: 185, start trb: 184, end trb: 184 Actually DMA pos already bigger than previous submit request afbccb7d's TRB (184-184). The reason of (not handled) is that deq position is wrong. The TRB link is below when irq happen. DEQ LINK LINK LINK LINK LINK .... TRB(afbccb7d):START DMA(EP_TRADDR). Original code check LINK TRB, but DEQ just move one step. LINK DEQ LINK LINK LINK LINK .... TRB(afbccb7d):START DMA(EP_TRADDR). This patch skip all LINK TRB and sync DEQ to trb's start. LINK LINK LINK LINK LINK .... DEQ = TRB(afbccb7d):START DMA(EP_TRADDR). Acked-by: Peter Chen <[email protected]> Cc: stable <[email protected]> Signed-off-by: Frank Li <[email protected]> Signed-off-by: Jun Li <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-12-03usb: typec: tcpm: Wait in SNK_DEBOUNCED until disconnectBadhri Jagan Sridharan1-4/+0
Stub from the spec: "4.5.2.2.4.2 Exiting from AttachWait.SNK State A Sink shall transition to Unattached.SNK when the state of both the CC1 and CC2 pins is SNK.Open for at least tPDDebounce. A DRP shall transition to Unattached.SRC when the state of both the CC1 and CC2 pins is SNK.Open for at least tPDDebounce." This change makes TCPM to wait in SNK_DEBOUNCED state until CC1 and CC2 pins is SNK.Open for at least tPDDebounce. Previously, TCPM resets the port if vbus is not present in PD_T_PS_SOURCE_ON. This causes TCPM to loop continuously when connected to a faulty power source that does not present vbus. Waiting in SNK_DEBOUNCED also ensures that TCPM is adherant to "4.5.2.2.4.2 Exiting from AttachWait.SNK State" requirements. [ 6169.280751] CC1: 0 -> 0, CC2: 0 -> 5 [state TOGGLING, polarity 0, connected] [ 6169.280759] state change TOGGLING -> SNK_ATTACH_WAIT [rev2 NONE_AMS] [ 6169.280771] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @ 170 ms [rev2 NONE_AMS] [ 6169.282427] CC1: 0 -> 0, CC2: 5 -> 5 [state SNK_ATTACH_WAIT, polarity 0, connected] [ 6169.450825] state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED [delayed 170 ms] [ 6169.450834] pending state change SNK_DEBOUNCED -> PORT_RESET @ 480 ms [rev2 NONE_AMS] [ 6169.930892] state change SNK_DEBOUNCED -> PORT_RESET [delayed 480 ms] [ 6169.931296] disable vbus discharge ret:0 [ 6169.931301] Setting usb_comm capable false [ 6169.932783] Setting voltage/current limit 0 mV 0 mA [ 6169.932802] polarity 0 [ 6169.933706] Requesting mux state 0, usb-role 0, orientation 0 [ 6169.936689] cc:=0 [ 6169.936812] pending state change PORT_RESET -> PORT_RESET_WAIT_OFF @ 100 ms [rev2 NONE_AMS] [ 6169.937157] CC1: 0 -> 0, CC2: 5 -> 0 [state PORT_RESET, polarity 0, disconnected] [ 6170.036880] state change PORT_RESET -> PORT_RESET_WAIT_OFF [delayed 100 ms] [ 6170.036890] state change PORT_RESET_WAIT_OFF -> SNK_UNATTACHED [rev2 NONE_AMS] [ 6170.036896] Start toggling [ 6170.041412] CC1: 0 -> 0, CC2: 0 -> 0 [state TOGGLING, polarity 0, disconnected] [ 6170.042973] CC1: 0 -> 0, CC2: 0 -> 5 [state TOGGLING, polarity 0, connected] [ 6170.042976] state change TOGGLING -> SNK_ATTACH_WAIT [rev2 NONE_AMS] [ 6170.042981] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @ 170 ms [rev2 NONE_AMS] [ 6170.213014] state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED [delayed 170 ms] [ 6170.213019] pending state change SNK_DEBOUNCED -> PORT_RESET @ 480 ms [rev2 NONE_AMS] [ 6170.693068] state change SNK_DEBOUNCED -> PORT_RESET [delayed 480 ms] [ 6170.693304] disable vbus discharge ret:0 [ 6170.693308] Setting usb_comm capable false [ 6170.695193] Setting voltage/current limit 0 mV 0 mA [ 6170.695210] polarity 0 [ 6170.695990] Requesting mux state 0, usb-role 0, orientation 0 [ 6170.701896] cc:=0 [ 6170.702181] pending state change PORT_RESET -> PORT_RESET_WAIT_OFF @ 100 ms [rev2 NONE_AMS] [ 6170.703343] CC1: 0 -> 0, CC2: 5 -> 0 [state PORT_RESET, polarity 0, disconnected] Fixes: f0690a25a140b8 ("staging: typec: USB Type-C Port Manager (tcpm)") Cc: [email protected] Acked-by: Heikki Krogerus <[email protected]> Signed-off-by: Badhri Jagan Sridharan <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-12-03USB: NO_LPM quirk Lenovo Powered USB-C Travel HubOle Ernst1-0/+3
This is another branded 8153 device that doesn't work well with LPM: r8152 2-2.1:1.0 enp0s13f0u2u1: Stop submitting intr, status -71 Disable LPM to resolve the issue. Signed-off-by: Ole Ernst <[email protected]> Cc: stable <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-12-03xhci: Fix commad ring abort, write all 64 bits to CRCR register.Mathias Nyman1-7/+14
Turns out some xHC controllers require all 64 bits in the CRCR register to be written to execute a command abort. The lower 32 bits containing the command abort bit is written first. In case the command ring stops before we write the upper 32 bits then hardware may use these upper bits to set the commnd ring dequeue pointer. Solve this by making sure the upper 32 bits contain a valid command ring dequeue pointer. The original patch that only wrote the first 32 to stop the ring went to stable, so this fix should go there as well. Fixes: ff0e50d3564f ("xhci: Fix command ring pointer corruption while aborting a command") Cc: [email protected] Tested-by: Pavankumar Kondeti <[email protected]> Signed-off-by: Mathias Nyman <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-12-03selftests/tc-testing: Fix cannot create /sys/bus/netdevsim/new_device: ↵Li Zhijian2-0/+2
Directory nonexistent Install netdevsim to provide /sys/bus/netdevsim/new_device interface. It helps to fix: # ok 97 9a7d - Change ETS strict band without quantum # skipped - skipped - previous setup failed 11 ce7d # # # -----> prepare stage *** Could not execute: "echo "1 1 4" > /sys/bus/netdevsim/new_device" # # -----> prepare stage *** Error message: "/bin/sh: 1: cannot create /sys/bus/netdevsim/new_device: Directory nonexistent # " # # -----> prepare stage *** Aborting test run. # # # <_io.BufferedReader name=5> *** stdout *** # Signed-off-by: Li Zhijian <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2021-12-03selftests/tc-testing: add missing configLi Zhijian1-0/+1
qdiscs/fq_pie requires CONFIG_NET_SCH_FQ_PIE, otherwise tc will fail to create a fq_pie qdisc. It fixes following issue: # not ok 57 83be - Create FQ-PIE with invalid number of flows # Command exited with 2, expected 0 # Error: Specified qdisc not found. Signed-off-by: Li Zhijian <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2021-12-03selftests/tc-testing: add exit codeLi Zhijian1-3/+5
Mark the summary result as FAIL to prevent from confusing the selftest framework if some of them are failed. Previously, the selftest framework always treats it as *ok* even though some of them are failed actually. That's because the script tdc.sh always return 0. # All test results: # # 1..97 # ok 1 83be - Create FQ-PIE with invalid number of flows # ok 2 8b6e - Create RED with no flags [...snip] # ok 6 5f15 - Create RED with flags ECN, harddrop # ok 7 53e8 - Create RED with flags ECN, nodrop # ok 8 d091 - Fail to create RED with only nodrop flag # ok 9 af8e - Create RED with flags ECN, nodrop, harddrop # not ok 10 ce7d - Add mq Qdisc to multi-queue device (4 queues) # Could not match regex pattern. Verify command output: # qdisc mq 1: root # qdisc fq_codel 0: parent 1:4 limit 10240p flows 1024 quantum 1514 target 5ms interval 100ms memory_limit 32Mb ecn drop_batch 64 # qdisc fq_codel 0: parent 1:3 limit 10240p flows 1024 quantum 1514 target 5ms interval 100ms memory_limit 32Mb ecn drop_batch 64 [...snip] # ok 96 6979 - Change quantum of a strict ETS band # ok 97 9a7d - Change ETS strict band without quantum # # # # ok 1 selftests: tc-testing: tdc.sh <<< summary result CC: Philip Li <[email protected]> Reported-by: kernel test robot <[email protected]> Signed-off-by: Li Zhijian <[email protected]> Acked-by: Davide Caratti <[email protected]> Acked-by: Jamal Hadi Salim <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2021-12-03bus: mhi: pci_generic: Fix device recovery failed issueSlark Xiao1-1/+1
For Foxconn T99W175 device(sdx55 platform) in some host platform, it would be unavailable once the host execute the err handler. After checking, it's caused by the delay time too short to get a successful reset. Please see my test evidence as bewlow(BTW, I add some extra test logs in function mhi_pci_reset_prepare and mhi_pci_reset_done): When MHI_POST_RESET_DELAY_MS equals to 500ms: Nov 4 14:30:03 jbd-ThinkEdge kernel: [ 146.222477] mhi mhi0: Device MHI is not in valid state Nov 4 14:30:03 jbd-ThinkEdge kernel: [ 146.222628] mhi-pci-generic 0000:2d:00.0: mhi_pci_reset_prepare reset Nov 4 14:30:03 jbd-ThinkEdge kernel: [ 146.222631] mhi-pci-generic 0000:2d:00.0: mhi_pci_reset_prepare mhi_soc_reset Nov 4 14:30:03 jbd-ThinkEdge kernel: [ 146.222632] mhi mhi0: mhi_soc_reset write soc to reset Nov 4 14:30:05 jbd-ThinkEdge kernel: [ 147.839993] mhi-pci-generic 0000:2d:00.0: mhi_pci_reset_done Nov 4 14:30:05 jbd-ThinkEdge kernel: [ 147.902063] mhi-pci-generic 0000:2d:00.0: reset failed When MHI_POST_RESET_DELAY_MS equals to 1000ms or 1500ms: Nov 4 19:07:26 jbd-ThinkEdge kernel: [ 157.067857] mhi mhi0: Device MHI is not in valid state Nov 4 19:07:26 jbd-ThinkEdge kernel: [ 157.068029] mhi-pci-generic 0000:2d:00.0: mhi_pci_reset_prepare reset Nov 4 19:07:26 jbd-ThinkEdge kernel: [ 157.068032] mhi-pci-generic 0000:2d:00.0: mhi_pci_reset_prepare mhi_soc_reset Nov 4 19:07:26 jbd-ThinkEdge kernel: [ 157.068034] mhi mhi0: mhi_soc_reset write soc to reset Nov 4 19:07:29 jbd-ThinkEdge kernel: [ 159.607006] mhi-pci-generic 0000:2d:00.0: mhi_pci_reset_done Nov 4 19:07:29 jbd-ThinkEdge kernel: [ 159.607152] mhi mhi0: Requested to power ON Nov 4 19:07:51 jbd-ThinkEdge kernel: [ 181.302872] mhi mhi0: Failed to reset MHI due to syserr state Nov 4 19:07:51 jbd-ThinkEdge kernel: [ 181.303011] mhi-pci-generic 0000:2d:00.0: failed to power up MHI controller When MHI_POST_RESET_DELAY_MS equals to 2000ms: Nov 4 17:51:08 jbd-ThinkEdge kernel: [ 147.180527] mhi mhi0: Failed to transition from PM state: Linkdown or Error Fatal Detect to: SYS ERROR Process Nov 4 17:51:08 jbd-ThinkEdge kernel: [ 147.180535] mhi mhi0: Device MHI is not in valid state Nov 4 17:51:08 jbd-ThinkEdge kernel: [ 147.180722] mhi-pci-generic 0000:2d:00.0: mhi_pci_reset_prepare reset Nov 4 17:51:08 jbd-ThinkEdge kernel: [ 147.180725] mhi-pci-generic 0000:2d:00.0: mhi_pci_reset_prepare mhi_soc_reset Nov 4 17:51:08 jbd-ThinkEdge kernel: [ 147.180727] mhi mhi0: mhi_soc_reset write soc to reset Nov 4 17:51:11 jbd-ThinkEdge kernel: [ 150.230787] mhi-pci-generic 0000:2d:00.0: mhi_pci_reset_done Nov 4 17:51:11 jbd-ThinkEdge kernel: [ 150.230928] mhi mhi0: Requested to power ON Nov 4 17:51:11 jbd-ThinkEdge kernel: [ 150.231173] mhi mhi0: Power on setup success Nov 4 17:51:14 jbd-ThinkEdge kernel: [ 153.254747] mhi mhi0: Wait for device to enter SBL or Mission mode I also tried big data like 3000, and it worked as well. 500ms may not be enough for all support mhi device. We shall increase it to 2000ms at least. Link: https://lore.kernel.org/r/[email protected] [mani: massaged commit message little bit, added Fixes tag and CCed stable] Fixes: 8ccc3279fcad ("mhi: pci_generic: Add support for reset") Cc: [email protected] Reviewed-by: Manivannan Sadhasivam <[email protected]> Signed-off-by: Slark Xiao <[email protected]> Signed-off-by: Manivannan Sadhasivam <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-12-03Merge tag 'phy-fixes-5.16' of ↵Greg Kroah-Hartman11-25/+30
git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy into char-misc-next Vinod writes: phy: fixes for 5.16 Fixes for: - kernel-doc warnings for various drivers - error handling fix for HiSilicon driver - name fix for zynqmp phy - property name fix in stm32 phy * tag 'phy-fixes-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: phy: HiSilicon: Fix copy and paste bug in error handling dt-bindings: phy: zynqmp-psgtr: fix USB phy name phy: ti: omap-usb2: Fix the kernel-doc style phy: qualcomm: ipq806x-usb: Fix kernel-doc style phy: ti: tusb1210: Fix the kernel-doc warn phy: qualcomm: usb-hsic: Fix the kernel-doc warn phy: qualcomm: qmp: Add missing struct documentation phy: mvebu-cp110-utmi: Fix kernel-doc warns phy: ti: report 2 non-kernel-doc comments phy: stm32: fix st,slow-hs-slew-rate with st,decrease-hs-slew-rate
2021-12-03HID: intel-ish-hid: ipc: only enable IRQ wakeup when requestedThomas Weißschuh1-2/+4
Fixes spurious wakeups from s0ix on Lenovo ThinkPad X1 Cargon Gen 9 on lid close. These wakeups are generated by interrupts from the ISH on changes to the lid status. By disabling the wake IRQ from the ISH we inhibit these spurious wakeups while keeping the resume from LID open through the ACPI interrupt. Reports on the Lenovo forums indicate that Lenovo ThinkPad X1 Yoga Gen6 is also affected. Fixes: ae02e5d40d5f ("HID: intel-ish-hid: ipc layer") BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=214855 Signed-off-by: Thomas Weißschuh <[email protected]> Acked-by: Srinivas Pandruvada <[email protected]> Signed-off-by: Benjamin Tissoires <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2021-12-03HID: google: add eel USB idxiazhengqiao2-0/+3
Add one additional hammer-like device. Signed-off-by: xiazhengqiao <[email protected]> Signed-off-by: Benjamin Tissoires <[email protected]> Link: https://lore.kernel.org/r/20211203030119.28612-1-xiazhengqiao@huaqin.corp-partner.google.com
2021-12-03HID: add USB_HID dependancy to hid-prodikeysGreg Kroah-Hartman1-1/+1
The prodikeys HID driver only controls USB devices, yet did not have a dependancy on USB_HID. This causes build errors on some configurations like nios2 when building due to new changes to the prodikeys driver. Reported-by: kernel test robot <[email protected]> Cc: [email protected] Cc: Jiri Kosina <[email protected]> Cc: Benjamin Tissoires <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]> Signed-off-by: Benjamin Tissoires <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2021-12-03HID: add USB_HID dependancy to hid-chiconyGreg Kroah-Hartman1-1/+1
The chicony HID driver only controls USB devices, yet did not have a dependancy on USB_HID. This causes build errors on some configurations like sparc when building due to new changes to the chicony driver. Reported-by: Stephen Rothwell <[email protected]> Cc: [email protected] Cc: Jiri Kosina <[email protected]> Cc: Benjamin Tissoires <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]> Signed-off-by: Benjamin Tissoires <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2021-12-03x86/64/mm: Map all kernel memory into trampoline_pgdJoerg Roedel1-1/+11
The trampoline_pgd only maps the 0xfffffff000000000-0xffffffffffffffff range of kernel memory (with 4-level paging). This range contains the kernel's text+data+bss mappings and the module mapping space but not the direct mapping and the vmalloc area. This is enough to get the application processors out of real-mode, but for code that switches back to real-mode the trampoline_pgd is missing important parts of the address space. For example, consider this code from arch/x86/kernel/reboot.c, function machine_real_restart() for a 64-bit kernel: #ifdef CONFIG_X86_32 load_cr3(initial_page_table); #else write_cr3(real_mode_header->trampoline_pgd); /* Exiting long mode will fail if CR4.PCIDE is set. */ if (boot_cpu_has(X86_FEATURE_PCID)) cr4_clear_bits(X86_CR4_PCIDE); #endif /* Jump to the identity-mapped low memory code */ #ifdef CONFIG_X86_32 asm volatile("jmpl *%0" : : "rm" (real_mode_header->machine_real_restart_asm), "a" (type)); #else asm volatile("ljmpl *%0" : : "m" (real_mode_header->machine_real_restart_asm), "D" (type)); #endif The code switches to the trampoline_pgd, which unmaps the direct mapping and also the kernel stack. The call to cr4_clear_bits() will find no stack and crash the machine. The real_mode_header pointer below points into the direct mapping, and dereferencing it also causes a crash. The reason this does not crash always is only that kernel mappings are global and the CR3 switch does not flush those mappings. But if theses mappings are not in the TLB already, the above code will crash before it can jump to the real-mode stub. Extend the trampoline_pgd to contain all kernel mappings to prevent these crashes and to make code which runs on this page-table more robust. Signed-off-by: Joerg Roedel <[email protected]> Signed-off-by: Borislav Petkov <[email protected]> Cc: [email protected] Link: https://lkml.kernel.org/r/[email protected]
2021-12-03objtool: Fix pv_ops noinstr validationPeter Zijlstra2-0/+5
Boris reported that in one of his randconfig builds, objtool got infinitely stuck. Turns out there's trivial list corruption in the pv_ops tracking when a function is both in a static table and in a code assignment. Avoid re-adding function to the pv_ops[] lists when they're already on it. Fixes: db2b0c5d7b6f ("objtool: Support pv_opsindirect calls for noinstr") Reported-by: Borislav Petkov <[email protected]> Signed-off-by: Peter Zijlstra (Intel) <[email protected]> Signed-off-by: Borislav Petkov <[email protected]> Tested-by: Borislav Petkov <[email protected]> Link: https://lkml.kernel.org/r/[email protected]
2021-12-02scsi: pm80xx: Do not call scsi_remove_host() in pm8001_alloc()Igor Pylypiv1-4/+2
Calling scsi_remove_host() before scsi_add_host() results in a crash: BUG: kernel NULL pointer dereference, address: 0000000000000108 RIP: 0010:device_del+0x63/0x440 Call Trace: device_unregister+0x17/0x60 scsi_remove_host+0xee/0x2a0 pm8001_pci_probe+0x6ef/0x1b90 [pm80xx] local_pci_probe+0x3f/0x90 We cannot call scsi_remove_host() in pm8001_alloc() because scsi_add_host() has not been called yet at that point in time. Function call tree: pm8001_pci_probe() | `- pm8001_pci_alloc() | | | `- pm8001_alloc() | | | `- scsi_remove_host() | `- scsi_add_host() Link: https://lore.kernel.org/r/[email protected] Fixes: 05c6c029a44d ("scsi: pm80xx: Increase number of supported queues") Reviewed-by: Vishakha Channapattan <[email protected]> Acked-by: Jack Wang <[email protected]> Signed-off-by: Igor Pylypiv <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2021-12-02selftests/fib_tests: Rework fib_rp_filter_test()Peilin Ye1-10/+49
Currently rp_filter tests in fib_tests.sh:fib_rp_filter_test() are failing. ping sockets are bound to dummy1 using the "-I" option (SO_BINDTODEVICE), but socket lookup is failing when receiving ping replies, since the routing table thinks they belong to dummy0. For example, suppose ping is using a SOCK_RAW socket for ICMP messages. When receiving ping replies, in __raw_v4_lookup(), sk->sk_bound_dev_if is 3 (dummy1), but dif (skb_rtable(skb)->rt_iif) says 2 (dummy0), so the raw_sk_bound_dev_eq() check fails. Similar things happen in ping_lookup() for SOCK_DGRAM sockets. These tests used to pass due to a bug [1] in iputils, where "ping -I" actually did not bind ICMP message sockets to device. The bug has been fixed by iputils commit f455fee41c07 ("ping: also bind the ICMP socket to the specific device") in 2016, which is why our rp_filter tests started to fail. See [2] . Fixing the tests while keeping everything in one netns turns out to be nontrivial. Rework the tests and build the following topology: ┌─────────────────────────────┐ ┌─────────────────────────────┐ │ network namespace 1 (ns1) │ │ network namespace 2 (ns2) │ │ │ │ │ │ ┌────┐ ┌─────┐ │ │ ┌─────┐ ┌────┐ │ │ │ lo │<───>│veth1│<────────┼────┼─>│veth2│<──────────>│ lo │ │ │ └────┘ ├─────┴──────┐ │ │ ├─────┴──────┐ └────┘ │ │ │192.0.2.1/24│ │ │ │192.0.2.1/24│ │ │ └────────────┘ │ │ └────────────┘ │ └─────────────────────────────┘ └─────────────────────────────┘ Consider sending an ICMP_ECHO packet A in ns2. Both source and destination IP addresses are 192.0.2.1, and we use strict mode rp_filter in both ns1 and ns2: 1. A is routed to lo since its destination IP address is one of ns2's local addresses (veth2); 2. A is redirected from lo's egress to veth2's egress using mirred; 3. A arrives at veth1's ingress in ns1; 4. A is redirected from veth1's ingress to lo's ingress, again, using mirred; 5. In __fib_validate_source(), fib_info_nh_uses_dev() returns false, since A was received on lo, but reverse path lookup says veth1; 6. However A is not dropped since we have relaxed this check for lo in commit 66f8209547cc ("fib: relax source validation check for loopback packets"); Making sure A is not dropped here in this corner case is the whole point of having this test. 7. As A reaches the ICMP layer, an ICMP_ECHOREPLY packet, B, is generated; 8. Similarly, B is redirected from lo's egress to veth1's egress (in ns1), then redirected once again from veth2's ingress to lo's ingress (in ns2), using mirred. Also test "ping 127.0.0.1" from ns2. It does not trigger the relaxed check in __fib_validate_source(), but just to make sure the topology works with loopback addresses. Tested with ping from iputils 20210722-41-gf9fb573: $ ./fib_tests.sh -t rp_filter IPv4 rp_filter tests TEST: rp_filter passes local packets [ OK ] TEST: rp_filter passes loopback packets [ OK ] [1] https://github.com/iputils/iputils/issues/55 [2] https://github.com/iputils/iputils/commit/f455fee41c077d4b700a473b2f5b3487b8febc1d Reported-by: Hangbin Liu <[email protected]> Fixes: adb701d6cfa4 ("selftests: add a test case for rp_filter") Reviewed-by: Cong Wang <[email protected]> Signed-off-by: Peilin Ye <[email protected]> Acked-by: David Ahern <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2021-12-02clk: imx: use module_platform_driverMiles Chen2-2/+2
Replace builtin_platform_driver_probe with module_platform_driver_probe because CONFIG_CLK_IMX8QXP can be set to =m (kernel module). Fixes: e0d0d4d86c766 ("clk: imx8qxp: Support building i.MX8QXP clock driver as module") Cc: Fabio Estevam <[email protected]> Cc: Stephen Boyd <[email protected]> Signed-off-by: Miles Chen <[email protected]> Link: https://lore.kernel.org/r/[email protected] Reviewed-by: Fabio Estevam <[email protected]> Reviewed-by: Stephen Boyd <[email protected]> Signed-off-by: Stephen Boyd <[email protected]>
2021-12-02clk: qcom: clk-alpha-pll: Don't reconfigure running TrionBjorn Andersson1-0/+9
In the event that the bootloader has configured the Trion PLL as source for the display clocks, e.g. for the continuous splashscreen, then there will also be RCGs that are clocked by this instance. Reconfiguring, and in particular disabling the output of, the PLL will cause issues for these downstream RCGs and has been shown to prevent them from being re-parented. Follow downstream and skip configuration if it's determined that the PLL is already running. Fixes: 59128c20a6a9 ("clk: qcom: clk-alpha-pll: Add support for controlling Lucid PLLs") Signed-off-by: Bjorn Andersson <[email protected]> Reviewed-by: Robert Foss <[email protected]> Reviewed-by: Vinod Koul <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Stephen Boyd <[email protected]>
2021-12-02clk: qcom: regmap-mux: fix parent clock lookupDmitry Baryshkov3-1/+15
The function mux_get_parent() uses qcom_find_src_index() to find the parent clock index, which is incorrect: qcom_find_src_index() uses src enum for the lookup, while mux_get_parent() should use cfg field (which corresponds to the register value). Add qcom_find_cfg_index() function doing this kind of lookup and use it for mux parent lookup. Fixes: df964016490b ("clk: qcom: add parent map for regmap mux") Cc: [email protected] Signed-off-by: Dmitry Baryshkov <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Stephen Boyd <[email protected]>
2021-12-02Merge tag 'drm-fixes-2021-12-03-1' of git://anongit.freedesktop.org/drm/drmLinus Torvalds39-159/+244
Pull drm fixes from Dave Airlie: "Bit of an uptick in patch count this week, though it's all relatively small overall. I suspect msm has been queuing up a few fixes to skew it here. Otherwise amdgpu has a scattered bunch of small fixes, and then some vc4, i915. virtio-gpu changes an rc1 introduced uAPI mistake, and makes it operate more like other drivers. This should be fine as no userspace relies on the behaviour yet. Summary: dma-buf: - memory leak fix msm: - kasan found memory overwrite - mmap flags - fencing error bug - ioctl NULL ptr - uninit var - devfreqless devices fix - dsi lanes fix - dp: avoid unpowered aux xfers amdgpu: - IP discovery based enumeration fixes - vkms fixes - DSC fixes for DP MST - Audio fix for hotplug with tiled displays - Misc display fixes - DP tunneling fix - DP fix - Aldebaran fix amdkfd: - Locking fix - Static checker fix - Fix double free i915: - backlight regression - Intel HDR backlight detection fix - revert TGL workaround that caused hangs virtio-gpu: - switch back to drm_poll vc4: - memory leak - error check fix - HVS modesetting fixes" * tag 'drm-fixes-2021-12-03-1' of git://anongit.freedesktop.org/drm/drm: (41 commits) Revert "drm/i915: Implement Wa_1508744258" drm/amdkfd: process_info lock not needed for svm drm/amdgpu: adjust the kfd reset sequence in reset sriov function drm/amd/display: add connector type check for CRC source set drm/amdkfd: fix double free mem structure drm/amdkfd: set "r = 0" explicitly before goto drm/amd/display: Add work around for tunneled MST. drm/amd/display: Fix for the no Audio bug with Tiled Displays drm/amd/display: Clear DPCD lane settings after repeater training drm/amd/display: Allow DSC on supported MST branch devices drm/amdgpu: Don't halt RLC on GFX suspend drm/amdgpu: fix the missed handling for SDMA2 and SDMA3 drm/amdgpu: check atomic flag to differeniate with legacy path drm/amdgpu: cancel the correct hrtimer on exit drm/amdgpu/sriov/vcn: add new vcn ip revision check case for SIENNA_CICHLID drm/i915/dp: Perform 30ms delay after source OUI write dma-buf: system_heap: Use 'for_each_sgtable_sg' in pages free flow drm/i915: Add support for panels with VESA backlights with PWM enable/disable drm/vc4: kms: Fix previous HVS commit wait drm/vc4: kms: Don't duplicate pending commit ...
2021-12-02Merge branch 'Fixes for kfunc-mod regressions and warnings'Andrii Nakryiko4-16/+18
Kumar Kartikeya says: ==================== This set includes fixes for two regressions and one build warning introduced by the kfunc for modules series. Changelog: ---------- v1 -> v2: v1: https://lore.kernel.org/bpf/[email protected] * Instead of demoting resolve_btfids warning to debug, only skip in case of set->cnt == 0. ==================== Signed-off-by: Andrii Nakryiko <[email protected]>
2021-12-02tools/resolve_btfids: Skip unresolved symbol warning for empty BTF setsKumar Kartikeya Dwivedi1-3/+5
resolve_btfids prints a warning when it finds an unresolved symbol, (id == 0) in id_patch. This can be the case for BTF sets that are empty (due to disabled config options), hence printing warnings for certain builds, most recently seen in [0]. The reason behind this is because id->cnt aliases id->id in btf_id struct, leading to empty set showing up as ID 0 when we get to id_patch, which triggers the warning. Since sets are an exception here, accomodate by reusing hole in btf_id for bool is_set member, setting it to true for BTF set when setting id->cnt, and use that to skip extraneous warning. [0]: https://lore.kernel.org/all/[email protected] Before: ; ./tools/bpf/resolve_btfids/resolve_btfids -v -b vmlinux net/ipv4/tcp_cubic.ko adding symbol tcp_cubic_kfunc_ids WARN: resolve_btfids: unresolved symbol tcp_cubic_kfunc_ids patching addr 0: ID 0 [tcp_cubic_kfunc_ids] sorting addr 4: cnt 0 [tcp_cubic_kfunc_ids] update ok for net/ipv4/tcp_cubic.ko After: ; ./tools/bpf/resolve_btfids/resolve_btfids -v -b vmlinux net/ipv4/tcp_cubic.ko adding symbol tcp_cubic_kfunc_ids patching addr 0: ID 0 [tcp_cubic_kfunc_ids] sorting addr 4: cnt 0 [tcp_cubic_kfunc_ids] update ok for net/ipv4/tcp_cubic.ko Fixes: 0e32dfc80bae ("bpf: Enable TCP congestion control kfunc from modules") Reported-by: Pavel Skripkin <[email protected]> Signed-off-by: Kumar Kartikeya Dwivedi <[email protected]> Signed-off-by: Andrii Nakryiko <[email protected]> Acked-by: Song Liu <[email protected]> Link: https://lore.kernel.org/bpf/[email protected]
2021-12-02bpf: Fix bpf_check_mod_kfunc_call for built-in modulesKumar Kartikeya Dwivedi1-2/+0
When module registering its set is built-in, THIS_MODULE will be NULL, hence we cannot return early in case owner is NULL. Fixes: 14f267d95fe4 ("bpf: btf: Introduce helpers for dynamic BTF set registration") Signed-off-by: Kumar Kartikeya Dwivedi <[email protected]> Signed-off-by: Andrii Nakryiko <[email protected]> Acked-by: Song Liu <[email protected]> Link: https://lore.kernel.org/bpf/[email protected]
2021-12-02bpf: Make CONFIG_DEBUG_INFO_BTF depend upon CONFIG_BPF_SYSCALLKumar Kartikeya Dwivedi3-11/+13
Vinicius Costa Gomes reported [0] that build fails when CONFIG_DEBUG_INFO_BTF is enabled and CONFIG_BPF_SYSCALL is disabled. This leads to btf.c not being compiled, and then no symbol being present in vmlinux for the declarations in btf.h. Since BTF is not useful without enabling BPF subsystem, disallow this combination. However, theoretically disabling both now could still fail, as the symbol for kfunc_btf_id_list variables is not available. This isn't a problem as the compiler usually optimizes the whole register/unregister call, but at lower optimization levels it can fail the build in linking stage. Fix that by adding dummy variables so that modules taking address of them still work, but the whole thing is a noop. [0]: https://lore.kernel.org/bpf/[email protected] Fixes: 14f267d95fe4 ("bpf: btf: Introduce helpers for dynamic BTF set registration") Reported-by: Vinicius Costa Gomes <[email protected]> Signed-off-by: Kumar Kartikeya Dwivedi <[email protected]> Signed-off-by: Andrii Nakryiko <[email protected]> Acked-by: Song Liu <[email protected]> Link: https://lore.kernel.org/bpf/[email protected]
2021-12-03Merge tag 'drm-intel-fixes-2021-12-02' of ↵Dave Airlie5-13/+42
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes - Fixing a regression where the backlight brightness control stopped working. - Fix the Intel HDR backlight support detection. - Reverting a w/a to fix a gpu Hang in TGL. The w/a itself was also for a hang, but in a much rarer scenario. The proper solution need to be done with help from user space and it will be addressed later. Signed-off-by: Dave Airlie <[email protected]> From: Rodrigo Vivi <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
2021-12-03Merge tag 'drm-misc-fixes-2021-12-02' of ↵Dave Airlie6-66/+28
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes Switch back to drm_poll for virtio, multiple fixes (memory leak, improper error check, some functional fixes too) for vc4, memory leak fix in dma-buf, Signed-off-by: Dave Airlie <[email protected]> From: Maxime Ripard <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/20211202084440.u3b7lbeulj7k3ltg@houat
2021-12-02Merge tag 'net-5.16-rc4' of ↵Linus Torvalds104-412/+1000
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net Pull networking fixes from Jakub Kicinski: "Including fixes from wireless, and wireguard. Mostly scattered driver changes this week, with one big clump in mv88e6xxx. Nothing of note, really. Current release - regressions: - smc: keep smc_close_final()'s error code during active close Current release - new code bugs: - iwlwifi: various static checker fixes (int overflow, leaks, missing error codes) - rtw89: fix size of firmware header before transfer, avoid crash - mt76: fix timestamp check in tx_status; fix pktid leak; - mscc: ocelot: fix missing unlock on error in ocelot_hwstamp_set() Previous releases - regressions: - smc: fix list corruption in smc_lgr_cleanup_early - ipv4: convert fib_num_tclassid_users to atomic_t Previous releases - always broken: - tls: fix authentication failure in CCM mode - vrf: reset IPCB/IP6CB when processing outbound pkts, prevent incorrect processing - dsa: mv88e6xxx: fixes for various device errata - rds: correct socket tunable error in rds_tcp_tune() - ipv6: fix memory leak in fib6_rule_suppress - wireguard: reset peer src endpoint when netns exits - wireguard: improve resilience to DoS around incoming handshakes - tcp: fix page frag corruption on page fault which involves TCP - mpls: fix missing attributes in delete notifications - mt7915: fix NULL pointer dereference with ad-hoc mode Misc: - rt2x00: be more lenient about EPROTO errors during start - mlx4_en: update reported link modes for 1/10G" * tag 'net-5.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (85 commits) net: dsa: b53: Add SPI ID table gro: Fix inconsistent indenting selftests: net: Correct case name net/rds: correct socket tunable error in rds_tcp_tune() mctp: Don't let RTM_DELROUTE delete local routes net/smc: Keep smc_close_final rc during active close ibmvnic: drop bad optimization in reuse_tx_pools() ibmvnic: drop bad optimization in reuse_rx_pools() net/smc: fix wrong list_del in smc_lgr_cleanup_early Fix Comment of ETH_P_802_3_MIN ethernet: aquantia: Try MAC address from device tree ipv4: convert fib_num_tclassid_users to atomic_t net: avoid uninit-value from tcp_conn_request net: annotate data-races on txq->xmit_lock_owner octeontx2-af: Fix a memleak bug in rvu_mbox_init() net/mlx4_en: Fix an use-after-free bug in mlx4_en_try_alloc_resources() vrf: Reset IPCB/IP6CB when processing outbound pkts in vrf dev xmit net: qlogic: qlcnic: Fix a NULL pointer dereference in qlcnic_83xx_add_rings() net: dsa: mv88e6xxx: Link in pcs_get_state() if AN is bypassed net: dsa: mv88e6xxx: Fix inband AN for 2500base-x on 88E6393X family ...
2021-12-02Merge tag 'trace-v5.16-rc3' of ↵Linus Torvalds4-1/+9
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace Pull tracing fixes from Steven Rostedt: "Three tracing fixes: - Allow compares of strings when using signed and unsigned characters - Fix kmemleak false positive for histogram entries - Handle negative numbers for user defined kretprobe data sizes" * tag 'trace-v5.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: kprobes: Limit max data_size of the kretprobe instances tracing: Fix a kmemleak false positive in tracing_map tracing/histograms: String compares should not care about signed values
2021-12-02Merge tag 'for-linus-5.16-2' of git://github.com/cminyard/linux-ipmiLinus Torvalds1-8/+33
Pull IPMI fixes from Corey Minyard: "Some changes that went in 5.16 had issues. When working on the design a piece was redesigned and things got missed. And the message type was not being initialized when it was allocated, resulting in crashes. In addition, the IPMI driver has had a shutdown issue where it could still have an item in a system workqueue after it had been shutdown. Move to a private workqueue to avoid that problem" * tag 'for-linus-5.16-2' of git://github.com/cminyard/linux-ipmi: ipmi:ipmb: Fix unknown command response ipmi: fix IPMI_SMI_MSG_TYPE_IPMB_DIRECT response length checking ipmi: fix oob access due to uninit smi_msg type ipmi: msghandler: Make symbol 'remove_work_wq' static ipmi: Move remove_work to dedicated workqueue
2021-12-02s390: update defconfigsHeiko Carstens3-3/+16
Signed-off-by: Heiko Carstens <[email protected]>
2021-12-02ALSA: ctl: Fix copy of updated id with element read/writeAlan Young1-0/+3
When control_compat.c:copy_ctl_value_to_user() is used, by ctl_elem_read_user() & ctl_elem_write_user(), it must also copy back the snd_ctl_elem_id value that may have been updated (filled in) by the call to snd_ctl_elem_read/snd_ctl_elem_write(). This matches the functionality provided by snd_ctl_elem_read_user() and snd_ctl_elem_write_user(), via snd_ctl_build_ioff(). Without this, and without making additional calls to snd_ctl_info() which are unnecessary when using the non-compat calls, a userspace application will not know the numid value for the element and consequently will not be able to use the poll/read interface on the control file to determine which elements have updates. Signed-off-by: Alan Young <[email protected]> Cc: <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Takashi Iwai <[email protected]>
2021-12-02Revert "drm/i915: Implement Wa_1508744258"José Roberto de Souza1-7/+0
This workarounds are causing hangs, because I missed the fact that it needs to be enabled for all cases and disabled when doing a resolve pass. So KMD only needs to whitelist it and UMD will be the one setting it on per case. This reverts commit 28ec02c9cbebf3feeaf21a59df9dfbc02bda3362. Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/4145 Signed-off-by: José Roberto de Souza <[email protected]> Fixes: 28ec02c9cbeb ("drm/i915: Implement Wa_1508744258") Reviewed-by: Matt Atwood <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/[email protected] (cherry picked from commit f3799ff16fcfacd44aee55db162830df461b631f) Signed-off-by: Rodrigo Vivi <[email protected]>
2021-12-02HID: bigbenff: prevent null pointer dereferenceBenjamin Tissoires1-1/+1
When emulating the device through uhid, there is a chance we don't have output reports and so report_field is null. Cc: [email protected] Signed-off-by: Benjamin Tissoires <[email protected]> Reviewed-by: Greg Kroah-Hartman <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2021-12-02HID: sony: fix error path in probeBenjamin Tissoires1-7/+15
When the setup of the GHL fails, we are not calling hid_hw_stop(). This leads to the hidraw node not being released, meaning a crash whenever somebody attempts to open the file. Cc: [email protected] Signed-off-by: Benjamin Tissoires <[email protected]> Reviewed-by: Greg Kroah-Hartman <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2021-12-02HID: add USB_HID dependancy on some USB HID driversGreg Kroah-Hartman1-3/+3
Some HID drivers are only for USB drivers, yet did not depend on CONFIG_USB_HID. This was hidden by the fact that the USB functions were stubbed out in the past, but now that drivers are checking for USB devices properly, build errors can occur with some random configurations. Reported-by: kernel test robot <[email protected]> Cc: [email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]> Signed-off-by: Benjamin Tissoires <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2021-12-02HID: check for valid USB device for many HID driversGreg Kroah-Hartman23-9/+92
Many HID drivers assume that the HID device assigned to them is a USB device as that was the only way HID devices used to be able to be created in Linux. However, with the additional ways that HID devices can be created for many different bus types, that is no longer true, so properly check that we have a USB device associated with the HID device before allowing a driver that makes this assumption to claim it. Cc: Jiri Kosina <[email protected]> Cc: Benjamin Tissoires <[email protected]> Cc: Michael Zaidman <[email protected]> Cc: Stefan Achatz <[email protected]> Cc: Maxime Coquelin <[email protected]> Cc: Alexandre Torgue <[email protected]> Cc: [email protected] Cc: [email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]> Tested-by: Benjamin Tissoires <[email protected]> [bentiss: amended for thrustmater.c hunk to apply] Signed-off-by: Benjamin Tissoires <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2021-12-02HID: wacom: fix problems when device is not a valid USB deviceGreg Kroah-Hartman1-5/+12
The wacom driver accepts devices of more than just USB types, but some code paths can cause problems if the device being controlled is not a USB device due to a lack of checking. Add the needed checks to ensure that the USB device accesses are only happening on a "real" USB device, and not one on some other bus. Cc: Jiri Kosina <[email protected]> Cc: Benjamin Tissoires <[email protected]> Cc: [email protected] Cc: [email protected] Tested-by: Benjamin Tissoires <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]> Signed-off-by: Benjamin Tissoires <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2021-12-02HID: add hid_is_usb() function to make it simpler for USB detectionGreg Kroah-Hartman6-9/+11
A number of HID drivers already call hid_is_using_ll_driver() but only for the detection of if this is a USB device or not. Make this more obvious by creating hid_is_usb() and calling the function that way. Also converts the existing hid_is_using_ll_driver() functions to use the new call. Cc: Jiri Kosina <[email protected]> Cc: Benjamin Tissoires <[email protected]> Cc: [email protected] Cc: [email protected] Tested-by: Benjamin Tissoires <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]> Signed-off-by: Benjamin Tissoires <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2021-12-02sched/cputime: Fix getrusage(RUSAGE_THREAD) with nohz_fullFrederic Weisbecker2-5/+12
getrusage(RUSAGE_THREAD) with nohz_full may return shorter utime/stime than the actual time. task_cputime_adjusted() snapshots utime and stime and then adjust their sum to match the scheduler maintained cputime.sum_exec_runtime. Unfortunately in nohz_full, sum_exec_runtime is only updated once per second in the worst case, causing a discrepancy against utime and stime that can be updated anytime by the reader using vtime. To fix this situation, perform an update of cputime.sum_exec_runtime when the cputime snapshot reports the task as actually running while the tick is disabled. The related overhead is then contained within the relevant situations. Reported-by: Hasegawa Hitomi <[email protected]> Signed-off-by: Frederic Weisbecker <[email protected]> Signed-off-by: Hasegawa Hitomi <[email protected]> Signed-off-by: Thomas Gleixner <[email protected]> Tested-by: Masayoshi Mizuma <[email protected]> Acked-by: Phil Auld <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2021-12-02timers/nohz: Last resort update jiffies on nohz_full IRQ entryFrederic Weisbecker2-1/+9
When at least one CPU runs in nohz_full mode, a dedicated timekeeper CPU is guaranteed to stay online and to never stop its tick. Meanwhile on some rare case, the dedicated timekeeper may be running with interrupts disabled for a while, such as in stop_machine. If jiffies stop being updated, a nohz_full CPU may end up endlessly programming the next tick in the past, taking the last jiffies update monotonic timestamp as a stale base, resulting in an tick storm. Here is a scenario where it matters: 0) CPU 0 is the timekeeper and CPU 1 a nohz_full CPU. 1) A stop machine callback is queued to execute somewhere. 2) CPU 0 reaches MULTI_STOP_DISABLE_IRQ while CPU 1 is still in MULTI_STOP_PREPARE. Hence CPU 0 can't do its timekeeping duty. CPU 1 can still take IRQs. 3) CPU 1 receives an IRQ which queues a timer callback one jiffy forward. 4) On IRQ exit, CPU 1 schedules the tick one jiffy forward, taking last_jiffies_update as a base. But last_jiffies_update hasn't been updated for 2 jiffies since the timekeeper has interrupts disabled. 5) clockevents_program_event(), which relies on ktime_get(), observes that the expiration is in the past and therefore programs the min delta event on the clock. 6) The tick fires immediately, goto 3) 7) Tick storm, the nohz_full CPU is drown and takes ages to reach MULTI_STOP_DISABLE_IRQ, which is the only way out of this situation. Solve this with unconditionally updating jiffies if the value is stale on nohz_full IRQ entry. IRQs and other disturbances are expected to be rare enough on nohz_full for the unconditional call to ktime_get() to actually matter. Reported-by: Paul E. McKenney <[email protected]> Signed-off-by: Frederic Weisbecker <[email protected]> Signed-off-by: Thomas Gleixner <[email protected]> Tested-by: Paul E. McKenney <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2021-12-02net: dsa: b53: Add SPI ID tableFlorian Fainelli1-0/+14
Currently autoloading for SPI devices does not use the DT ID table, it uses SPI modalises. Supporting OF modalises is going to be difficult if not impractical, an attempt was made but has been reverted, so ensure that module autoloading works for this driver by adding an id_table listing the SPI IDs for everything. Fixes: 96c8395e2166 ("spi: Revert modalias changes") Signed-off-by: Florian Fainelli <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2021-12-02gro: Fix inconsistent indentingJiapeng Chong1-3/+3
Eliminate the follow smatch warning: net/ipv6/ip6_offload.c:249 ipv6_gro_receive() warn: inconsistent indenting. Reported-by: Abaci Robot <[email protected]> Signed-off-by: Jiapeng Chong <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Powered by cgit, Gruvboxed by Blaster4385.