aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2024-10-18ASoC/SoundWire: clean up link DMA during stop for IPC4Mark Brown4-32/+62
Merge series from Bard Liao <[email protected]>: Clean up the link DMA for playback during stop for IPC4 is required to reset the DMA read/write pointers when the stream is prepared and restarted after a call to snd_pcm_drain()/snd_pcm_drop(). The change is mainly on ASoC. We may go via ASoC tree with Vinod's Acked-by tag Ranjani Sridharan (4): ASoC: SOF: ipc4-topology: Do not set ALH node_id for aggregated DAIs ASoC: SOF: Intel: hda: Handle prepare without close for non-HDA DAI's soundwire: intel_ace2x: Send PDI stream number during prepare ASoC: SOF: Intel: hda: Always clean up link DMA during stop drivers/soundwire/intel_ace2x.c | 19 +++++----------- sound/soc/sof/intel/hda-dai-ops.c | 23 +++++++++---------- sound/soc/sof/intel/hda-dai.c | 37 +++++++++++++++++++++++++++---- sound/soc/sof/ipc4-topology.c | 15 +++++++++++-- 4 files changed, 62 insertions(+), 32 deletions(-) -- 2.43.0
2024-10-18ASoC: fsl_micfil: Add a flag to distinguish with different volume control typesChancel Liu1-1/+42
On i.MX8MM the register of volume control has positive and negative values. It is different from other platforms like i.MX8MP and i.MX93 which only have positive values. Add a volume_sx flag to use SX_TLV volume control for this kind of platform. Use common TLV volume control for other platforms. Fixes: cdfa92eb90f5 ("ASoC: fsl_micfil: Correct the number of steps on SX controls") Signed-off-by: Chancel Liu <[email protected]> Reviewed-by: Daniel Baluta <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Mark Brown <[email protected]>
2024-10-18ASoC: codecs: lpass-rx-macro: fix RXn(rx,n) macro for DSM_CTL and SEC7 regsAlexey Klimov1-8/+7
Turns out some registers of pre-2.5 version of rxmacro codecs are not located at the expected offsets but 0xc further away in memory. So far the detected registers are CDC_RX_RX2_RX_PATH_SEC7 and CDC_RX_RX2_RX_PATH_DSM_CTL. CDC_RX_RXn_RX_PATH_DSM_CTL(rx, n) macro incorrectly generates the address 0x540 for RX2 but it should be 0x54C and it also overwrites CDC_RX_RX2_RX_PATH_SEC7 which is located at 0x540. The same goes for CDC_RX_RXn_RX_PATH_SEC7(rx, n). Fix this by introducing additional rxn_reg_stride2 offset. For 2.5 version and above this offset will be equal to 0. With such change the corresponding RXn() macros will generate the same values for 2.5 codec version for all RX paths and the same old values for pre-2.5 version for RX0 and RX1. However for the latter case with RX2 path it will also add rxn_reg_stride2 on top. While at this, also remove specific if-check for INTERP_AUX from rx_macro_digital_mute() and rx_macro_enable_interp_clk(). These if-check was used to handle such special offset for AUX interpolator but since CDC_RX_RXn_RX_PATH_SEC7(rx, n) and CDC_RX_RXn_RX_PATH_DSM_CTL(rx, n) macros will generate the correst addresses of dsm register, they are no longer needed. Cc: Srinivas Kandagatla <[email protected]> Cc: Krzysztof Kozlowski <[email protected]> Signed-off-by: Alexey Klimov <[email protected]> Reviewed-by: Dmitry Baryshkov <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Mark Brown <[email protected]>
2024-10-17ASoC: Change my e-mail to gmailKirill Marinushkin5-8/+8
Change my contact e-mail in pcm3060 driver and MAINTAINERS Signed-off-by: Kirill Marinushkin <[email protected]> Cc: Kirill Marinushkin <[email protected]> Cc: Liam Girdwood <[email protected]> Cc: Mark Brown <[email protected]> Cc: Jaroslav Kysela <[email protected]> Cc: Takashi Iwai <[email protected]> Cc: [email protected] Cc: [email protected] Link: https://patch.msgid.link/[email protected] Signed-off-by: Mark Brown <[email protected]>
2024-10-17ASoC: Intel: soc-acpi: lnl: Add match entry for TM2 laptopsDerek Fang1-0/+38
Add a new match table entry on Lunarlake for the TM2 laptops with rt713 and rt1318. Signed-off-by: Derek Fang <[email protected]> Reviewed-by: Péter Ujfalusi <[email protected]> Reviewed-by: Ranjani Sridharan <[email protected]> Signed-off-by: Bard Liao <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Mark Brown <[email protected]>
2024-10-17ASoC: amd: yc: Fix non-functional mic on ASUS E1404FAIlya Dudikov1-0/+7
ASUS Vivobook E1404FA needs a quirks-table entry for the internal microphone to function properly. Signed-off-by: Ilya Dudikov <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Mark Brown <[email protected]>
2024-10-17ASoC: SOF: Intel: hda: Always clean up link DMA during stopRanjani Sridharan2-13/+11
This is required to reset the DMA read/write pointers when the stream is prepared and restarted after a call to snd_pcm_drain()/snd_pcm_drop(). Also, now that the stream is reset during stop, do not save LLP registers in the case of STOP/suspend to avoid erroneous delay reporting. Link: https://github.com/thesofproject/sof/issues/9502 Signed-off-by: Ranjani Sridharan <[email protected]> Reviewed-by: Péter Ujfalusi <[email protected]> Reviewed-by: Kai Vehmanen <[email protected]> Signed-off-by: Bard Liao <[email protected]> All: [email protected] # 6.10.x 6.11.x Link: https://patch.msgid.link/[email protected] Signed-off-by: Mark Brown <[email protected]>
2024-10-17soundwire: intel_ace2x: Send PDI stream number during prepareRanjani Sridharan1-13/+6
In the case of a prepare callback after an xrun or when the PCM is restarted after a call to snd_pcm_drain/snd_pcm_drop, avoid reprogramming the SHIM registers but send the PDI stream number so that the link DMA data can be set. This is needed for the case that the DMA data is cleared when the PCM is stopped and restarted without being closed. Link: https://github.com/thesofproject/sof/issues/9502 Signed-off-by: Ranjani Sridharan <[email protected]> Reviewed-by: Péter Ujfalusi <[email protected]> Reviewed-by: Kai Vehmanen <[email protected]> Signed-off-by: Bard Liao <[email protected]> Acked-by: Vinod Koul <[email protected]> All: [email protected] # 6.10.x 6.11.x Link: https://patch.msgid.link/[email protected] Signed-off-by: Mark Brown <[email protected]>
2024-10-17ASoC: SOF: Intel: hda: Handle prepare without close for non-HDA DAI'sRanjani Sridharan1-4/+32
When a PCM is restarted after a snd_pcm_drain/snd_pcm_drop(), the prepare callback will be invoked and the hw_params will be set again. For the HDA DAI's, the hw_params function handles this case already but not for the non-HDA DAI's. So, add the check for link_prepared to verify if the hw_params should be done again or not. Additionally, for SDW DAI's reset the PCMSyCM registers as would be done in the case of a start after a hw_free. Signed-off-by: Ranjani Sridharan <[email protected]> Reviewed-by: Péter Ujfalusi <[email protected]> Reviewed-by: Kai Vehmanen <[email protected]> Signed-off-by: Bard Liao <[email protected]> All: [email protected] # 6.10.x 6.11.x Link: https://patch.msgid.link/[email protected] Signed-off-by: Mark Brown <[email protected]>
2024-10-17ASoC: SOF: ipc4-topology: Do not set ALH node_id for aggregated DAIsRanjani Sridharan1-2/+13
For aggregated DAIs, the node ID is set to the group_id during the DAI widget's ipc_prepare op. With the current logic, setting the dai_index for node_id in the dai_config is redundant as it will be overwritten with the group_id anyway. Removing it will also prevent any accidental clearing/resetting of the group_id for aggregated DAIs due to the dai_config calls could that happen before the allocated group_id is freed. Signed-off-by: Ranjani Sridharan <[email protected]> Reviewed-by: Péter Ujfalusi <[email protected]> Reviewed-by: Kai Vehmanen <[email protected]> Signed-off-by: Bard Liao <[email protected]> All: [email protected] # 6.10.x 6.11.x Link: https://patch.msgid.link/[email protected] Signed-off-by: Mark Brown <[email protected]>
2024-10-14MAINTAINERS: Update maintainer list for MICROCHIP ASOC, SSC and MCP16502 driversAndrei Simion1-0/+3
To help Claudiu and offload the work, add myself to the maintainer list for those drivers. Acked-by: Claudiu Beznea <[email protected]> Signed-off-by: Andrei Simion <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Mark Brown <[email protected]>
2024-10-12ASoC: qcom: Select missing common Soundwire module code on SDM845Krzysztof Kozlowski1-0/+1
SDM845 sound card driver uses qcom_snd_sdw_startup() from the common Soundwire module, so select it to fix build failures: ERROR: modpost: "qcom_snd_sdw_startup" [sound/soc/qcom/snd-soc-sdm845.ko] undefined! Fixes: d0e806b0cc62 ("ASoC: qcom: sdm845: add missing soundwire runtime stream alloc") Signed-off-by: Krzysztof Kozlowski <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Mark Brown <[email protected]>
2024-10-11ASoC: fsl_esai: change dev_warn to dev_dbg in irq handlerShengjiu Wang1-2/+2
Irq handler need to be executed as fast as possible, so the log in irq handler is better to use dev_dbg which needs to be enabled when debugging. Signed-off-by: Shengjiu Wang <[email protected]> Reviewed-by: Iuliana Prodan <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Mark Brown <[email protected]>
2024-10-11ASoC: rsnd: Fix probe failure on HiHope boards due to endpoint parsingLad Prabhakar1-2/+5
On the HiHope boards, we have a single port with a single endpoint defined as below: .... rsnd_port: port { rsnd_endpoint: endpoint { remote-endpoint = <&dw_hdmi0_snd_in>; dai-format = "i2s"; bitclock-master = <&rsnd_endpoint>; frame-master = <&rsnd_endpoint>; playback = <&ssi2>; }; }; .... With commit 547b02f74e4a ("ASoC: rsnd: enable multi Component support for Audio Graph Card/Card2"), support for multiple ports was added. This caused probe failures on HiHope boards, as the endpoint could not be retrieved due to incorrect device node pointers being used. This patch fixes the issue by updating the `rsnd_dai_of_node()` and `rsnd_dai_probe()` functions to use the correct device node pointers based on the port names ('port' or 'ports'). It ensures that the endpoint is properly parsed for both single and multi-port configurations, restoring compatibility with HiHope boards. Fixes: 547b02f74e4a ("ASoC: rsnd: enable multi Component support for Audio Graph Card/Card2") Signed-off-by: Lad Prabhakar <[email protected]> Acked-by: Kuninori Morimoto <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Mark Brown <[email protected]>
2024-10-11ASoC: max98388: Fix missing increment of variable slot_foundColin Ian King1-0/+1
The variable slot_found is being initialized to zero and inside a for-loop is being checked if it's reached MAX_NUM_CH, however, this is currently impossible since slot_found is never changed. In a previous loop a similar coding pattern is used and slot_found is being incremented. It appears the increment of slot_found is missing from the loop, so fix the code by adding in the increment. Fixes: 6a8e1d46f062 ("ASoC: max98388: add amplifier driver") Signed-off-by: Colin Ian King <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Mark Brown <[email protected]>
2024-10-10ASoC: amd: yc: Add quirk for ASUS Vivobook S15 M3502RAChristian Heusel1-0/+7
As reported the builtin microphone doesn't work on the ASUS Vivobook model S15 OLED M3502RA. Therefore add a quirk for it to make it work. Link: https://bugzilla.kernel.org/show_bug.cgi?id=219345 Signed-off-by: Christian Heusel <[email protected]> Link: https://patch.msgid.link/20241010-bugzilla-219345-asus-vivobook-v1-1-3bb24834e2c3@heusel.eu Signed-off-by: Mark Brown <[email protected]>
2024-10-10ASoC: topology: Bump minimal topology ABI versionAmadeusz Sławiński1-1/+1
When v4 topology support was removed, minimal topology ABI version should have been bumped. Fixes: fe4a07454256 ("ASoC: Drop soc-topology ABI v4 support") Reviewed-by: Cezary Rojewski <[email protected]> Signed-off-by: Amadeusz Sławiński <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Mark Brown <[email protected]>
2024-10-10ASoC: codecs: Fix error handling in aw_dev_get_dsp_status functionZhu Jun1-1/+1
Added proper error handling for register value check that return -EPERM when register value does not meet expected condition Signed-off-by: Zhu Jun <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Mark Brown <[email protected]>
2024-10-10ASoC: qcom: sdm845: add missing soundwire runtime stream allocAlexey Klimov1-1/+6
During the migration of Soundwire runtime stream allocation from the Qualcomm Soundwire controller to SoC's soundcard drivers the sdm845 soundcard was forgotten. At this point any playback attempt or audio daemon startup, for instance on sdm845-db845c (Qualcomm RB3 board), will result in stream pointer NULL dereference: Unable to handle kernel NULL pointer dereference at virtual address 0000000000000020 Mem abort info: ESR = 0x0000000096000004 EC = 0x25: DABT (current EL), IL = 32 bits SET = 0, FnV = 0 EA = 0, S1PTW = 0 FSC = 0x04: level 0 translation fault Data abort info: ISV = 0, ISS = 0x00000004, ISS2 = 0x00000000 CM = 0, WnR = 0, TnD = 0, TagAccess = 0 GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 user pgtable: 4k pages, 48-bit VAs, pgdp=0000000101ecf000 [0000000000000020] pgd=0000000000000000, p4d=0000000000000000 Internal error: Oops: 0000000096000004 [#1] PREEMPT SMP Modules linked in: ... CPU: 5 UID: 0 PID: 1198 Comm: aplay Not tainted 6.12.0-rc2-qcomlt-arm64-00059-g9d78f315a362-dirty #18 Hardware name: Thundercomm Dragonboard 845c (DT) pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : sdw_stream_add_slave+0x44/0x380 [soundwire_bus] lr : sdw_stream_add_slave+0x44/0x380 [soundwire_bus] sp : ffff80008a2035c0 x29: ffff80008a2035c0 x28: ffff80008a203978 x27: 0000000000000000 x26: 00000000000000c0 x25: 0000000000000000 x24: ffff1676025f4800 x23: ffff167600ff1cb8 x22: ffff167600ff1c98 x21: 0000000000000003 x20: ffff167607316000 x19: ffff167604e64e80 x18: 0000000000000000 x17: 0000000000000000 x16: ffffcec265074160 x15: 0000000000000000 x14: 0000000000000000 x13: 0000000000000000 x12: 0000000000000000 x11: 0000000000000000 x10: 0000000000000000 x9 : 0000000000000000 x8 : 0000000000000000 x7 : 0000000000000000 x6 : ffff167600ff1cec x5 : ffffcec22cfa2010 x4 : 0000000000000000 x3 : 0000000000000003 x2 : ffff167613f836c0 x1 : 0000000000000000 x0 : ffff16761feb60b8 Call trace: sdw_stream_add_slave+0x44/0x380 [soundwire_bus] wsa881x_hw_params+0x68/0x80 [snd_soc_wsa881x] snd_soc_dai_hw_params+0x3c/0xa4 __soc_pcm_hw_params+0x230/0x660 dpcm_be_dai_hw_params+0x1d0/0x3f8 dpcm_fe_dai_hw_params+0x98/0x268 snd_pcm_hw_params+0x124/0x460 snd_pcm_common_ioctl+0x998/0x16e8 snd_pcm_ioctl+0x34/0x58 __arm64_sys_ioctl+0xac/0xf8 invoke_syscall+0x48/0x104 el0_svc_common.constprop.0+0x40/0xe0 do_el0_svc+0x1c/0x28 el0_svc+0x34/0xe0 el0t_64_sync_handler+0x120/0x12c el0t_64_sync+0x190/0x194 Code: aa0403fb f9418400 9100e000 9400102f (f8420f22) ---[ end trace 0000000000000000 ]--- 0000000000006108 <sdw_stream_add_slave>: 6108: d503233f paciasp 610c: a9b97bfd stp x29, x30, [sp, #-112]! 6110: 910003fd mov x29, sp 6114: a90153f3 stp x19, x20, [sp, #16] 6118: a9025bf5 stp x21, x22, [sp, #32] 611c: aa0103f6 mov x22, x1 6120: 2a0303f5 mov w21, w3 6124: a90363f7 stp x23, x24, [sp, #48] 6128: aa0003f8 mov x24, x0 612c: aa0203f7 mov x23, x2 6130: a9046bf9 stp x25, x26, [sp, #64] 6134: aa0403f9 mov x25, x4 <-- x4 copied to x25 6138: a90573fb stp x27, x28, [sp, #80] 613c: aa0403fb mov x27, x4 6140: f9418400 ldr x0, [x0, #776] 6144: 9100e000 add x0, x0, #0x38 6148: 94000000 bl 0 <mutex_lock> 614c: f8420f22 ldr x2, [x25, #32]! <-- offset 0x44 ^^^ This is 0x6108 + offset 0x44 from the beginning of sdw_stream_add_slave() where data abort happens. wsa881x_hw_params() is called with stream = NULL and passes it further in register x4 (5th argument) to sdw_stream_add_slave() without any checks. Value from x4 is copied to x25 and finally it aborts on trying to load a value from address in x25 plus offset 32 (in dec) which corresponds to master_list member in struct sdw_stream_runtime: struct sdw_stream_runtime { const char * name; /* 0 8 */ struct sdw_stream_params params; /* 8 12 */ enum sdw_stream_state state; /* 20 4 */ enum sdw_stream_type type; /* 24 4 */ /* XXX 4 bytes hole, try to pack */ here-> struct list_head master_list; /* 32 16 */ int m_rt_count; /* 48 4 */ /* size: 56, cachelines: 1, members: 6 */ /* sum members: 48, holes: 1, sum holes: 4 */ /* padding: 4 */ /* last cacheline: 56 bytes */ Fix this by adding required calls to qcom_snd_sdw_startup() and sdw_release_stream() to startup and shutdown routines which restores the previous correct behaviour when ->set_stream() method is called to set a valid stream runtime pointer on playback startup. Reproduced and then fix was tested on db845c RB3 board. Reported-by: Dmitry Baryshkov <[email protected]> Cc: [email protected] Fixes: 15c7fab0e047 ("ASoC: qcom: Move Soundwire runtime stream alloc to soundcards") Cc: Srinivas Kandagatla <[email protected]> Cc: Dmitry Baryshkov <[email protected]> Cc: Krzysztof Kozlowski <[email protected]> Cc: Pierre-Louis Bossart <[email protected]> Signed-off-by: Alexey Klimov <[email protected]> Tested-by: Steev Klimaszewski <[email protected]> # Lenovo Yoga C630 Reviewed-by: Krzysztof Kozlowski <[email protected]> Reviewed-by: Srinivas Kandagatla <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Mark Brown <[email protected]>
2024-10-10ASoC: loongson: Fix component check failed on FDT systemsBinbin Zhou1-0/+1
Add missing snd_soc_dai_link.platforms assignment to avoid soc_dai_link_sanity_check() failure. Fixes: d24028606e76 ("ASoC: loongson: Add Loongson ASoC Sound Card Support") Signed-off-by: Binbin Zhou <[email protected]> Link: https://patch.msgid.link/6645888f2f9e8a1d8d799109f867d0f97fd78c58.1728459624.git.zhoubinbin@loongson.cn Signed-off-by: Mark Brown <[email protected]>
2024-10-08ASoC: dapm: avoid container_of() to get componentBenjamin Bara1-2/+2
The current implementation does not work for widgets of DAPMs without component, as snd_soc_dapm_to_component() requires it. If the widget is directly owned by the card, e.g. as it is the case for the tegra implementation, the call leads to UB. Therefore directly access the component of the widget's DAPM to be able to check if a component is available. Fixes: f82eb06a40c8 ("ASoC: tegra: machine: Handle component name prefix") Cc: [email protected] # v6.7+ Signed-off-by: Benjamin Bara <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Mark Brown <[email protected]>
2024-10-08ASoC: SOF: Intel: hda-loader: do not wait for HDaudio IOCKai Vehmanen1-17/+0
Commit 9ee3f0d8c999 ("ASOC: SOF: Intel: hda-loader: only wait for HDaudio IOC for IPC4 devices") removed DMA wait for IPC3 case. Proceed and remove the wait for IPC4 devices as well. There is no dependency to IPC version in the load logic and checking the firmware status is a sufficient check in case of errors. The removed code also had a bug in that -ETIMEDOUT is returned without stopping the DMA transfer. Cc: [email protected] Link: https://github.com/thesofproject/linux/issues/5135 Fixes: 9ee3f0d8c999 ("ASOC: SOF: Intel: hda-loader: only wait for HDaudio IOC for IPC4 devices") Suggested-by: Peter Ujfalusi <[email protected]> Signed-off-by: Kai Vehmanen <[email protected]> Reviewed-by: Péter Ujfalusi <[email protected]> Reviewed-by: Pierre-Louis Bossart <[email protected]> Reviewed-by: Ranjani Sridharan <[email protected]> Signed-off-by: Peter Ujfalusi <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Mark Brown <[email protected]>
2024-10-08ASoC: SOF: amd: Fix for ACP SRAM addr for acp7.0 platformVenkata Prasad Potturu1-1/+4
Incorrect SRAM base addr for acp7.0 platform results firmware boot failure. Add condition check to support SRAM addr for various platforms. Fixes: 145d7e5ae8f4 ("ASoC: SOF: amd: add option to use sram for data bin loading") Signed-off-by: Venkata Prasad Potturu <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Mark Brown <[email protected]>
2024-10-08ASoC: SOF: amd: Add error log for DSP firmware validation failureVenkata Prasad Potturu1-1/+3
Add dev_err to print ACP_SHA_DSP_FW_QUALIFIER and ACP_SHA_PSP_ACK register values for PSP firmware validation failure case. Signed-off-by: Venkata Prasad Potturu <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Mark Brown <[email protected]>
2024-10-08ASoC: Intel: avs: Update stream status in a separate threadAmadeusz Sławiński3-1/+37
Function snd_pcm_period_elapsed() is part of sequence servicing HDAudio stream IRQs. It's called under Global Interrupt Enable (GIE) disabled - no HDAudio interrupts will be raised. At the same time, the function may end up calling __snd_pcm_xrun() or snd_pcm_drain_done(). On the avs-driver side, this translates to IPCs and as GIE is disabled, these will never complete successfully. Improve system stability by scheduling stream-IRQ handling in a separate thread. Signed-off-by: Amadeusz Sławiński <[email protected]> Reviewed-by: Cezary Rojewski <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Mark Brown <[email protected]>
2024-10-07ASoC: dt-bindings: davinci-mcasp: Fix interrupt propertiesMiquel Raynal1-9/+9
Combinations of "tx" alone, "rx" alone and "tx", "rx" together are supposedly valid (see link below), which is not the case today as "rx" alone is not accepted by the current binding. Let's rework the two interrupt properties to expose all correct possibilities. Cc: Péter Ujfalusi <[email protected]> Link: https://lore.kernel.org/linux-sound/20241003102552.2c11840e@xps-13/T/#m277fce1d49c50d94e071f7890aed472fa2c64052 Fixes: 8be90641a0bb ("ASoC: dt-bindings: davinci-mcasp: convert McASP bindings to yaml schema") Signed-off-by: Miquel Raynal <[email protected]> Acked-by: Krzysztof Kozlowski <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Mark Brown <[email protected]>
2024-10-07ASoC: qcom: Fix NULL Dereference in asoc_qcom_lpass_cpu_platform_probe()Zichen Xie1-0/+2
A devm_kzalloc() in asoc_qcom_lpass_cpu_platform_probe() could possibly return NULL pointer. NULL Pointer Dereference may be triggerred without addtional check. Add a NULL check for the returned pointer. Fixes: b5022a36d28f ("ASoC: qcom: lpass: Use regmap_field for i2sctl and dmactl registers") Cc: [email protected] Signed-off-by: Zichen Xie <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Mark Brown <[email protected]>
2024-10-06Linux 6.12-rc2Linus Torvalds1-1/+1
2024-10-06Merge tag 'kbuild-fixes-v6.12' of ↵Linus Torvalds7-8/+66
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild Pull Kbuild fixes from Masahiro Yamada: - Move non-boot built-in DTBs to the .rodata section - Fix Kconfig bugs - Fix maint scripts in the linux-image Debian package - Import some list macros to scripts/include/ * tag 'kbuild-fixes-v6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: kbuild: deb-pkg: Remove blank first line from maint scripts kbuild: fix a typo dt_binding_schema -> dt_binding_schemas scripts: import more list macros kconfig: qconf: fix buffer overflow in debug links kconfig: qconf: move conf_read() before drawing tree pain kconfig: clear expr::val_is_valid when allocated kconfig: fix infinite loop in sym_calc_choice() kbuild: move non-boot built-in DTBs to .rodata section
2024-10-06Merge tag 'platform-drivers-x86-v6.12-2' of ↵Linus Torvalds9-17/+30
git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86 Pull x86 platform driver fixes from Hans de Goede: - Intel PMC fix for suspend/resume issues on some Sky and Kaby Lake laptops - Intel Diamond Rapids hw-id additions - Documentation and MAINTAINERS fixes - Some other small fixes * tag 'platform-drivers-x86-v6.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: platform/x86: x86-android-tablets: Fix use after free on platform_device_register() errors platform/x86: wmi: Update WMI driver API documentation platform/x86: dell-ddv: Fix typo in documentation platform/x86: dell-sysman: add support for alienware products platform/x86/intel: power-domains: Add Diamond Rapids support platform/x86: ISST: Add Diamond Rapids to support list platform/x86:intel/pmc: Disable ACPI PM Timer disabling on Sky and Kaby Lake platform/x86: dell-laptop: Do not fail when encountering unsupported batteries MAINTAINERS: Update Intel In Field Scan(IFS) entry platform/x86: ISST: Fix the KASAN report slab-out-of-bounds bug
2024-10-06Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvmLinus Torvalds12-43/+91
Pull kvm fixes from Paolo Bonzini: "ARM64: - Fix pKVM error path on init, making sure we do not change critical system registers as we're about to fail - Make sure that the host's vector length is at capped by a value common to all CPUs - Fix kvm_has_feat*() handling of "negative" features, as the current code is pretty broken - Promote Joey to the status of official reviewer, while James steps down -- hopefully only temporarly x86: - Fix compilation with KVM_INTEL=KVM_AMD=n - Fix disabling KVM_X86_QUIRK_SLOT_ZAP_ALL when shadow MMU is in use Selftests: - Fix compilation on non-x86 architectures" * tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: x86/reboot: emergency callbacks are now registered by common KVM code KVM: x86: leave kvm.ko out of the build if no vendor module is requested KVM: x86/mmu: fix KVM_X86_QUIRK_SLOT_ZAP_ALL for shadow MMU KVM: arm64: Fix kvm_has_feat*() handling of negative features KVM: selftests: Fix build on architectures other than x86_64 KVM: arm64: Another reviewer reshuffle KVM: arm64: Constrain the host to the maximum shared SVE VL with pKVM KVM: arm64: Fix __pkvm_init_vcpu cptr_el2 error path
2024-10-06Merge tag 'powerpc-6.12-3' of ↵Linus Torvalds1-1/+1
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux Pull powerpc fix from Michael Ellerman: - Allow r30 to be used in vDSO code generation of getrandom Thanks to Jason A. Donenfeld * tag 'powerpc-6.12-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: powerpc/vdso: allow r30 in vDSO code generation of getrandom
2024-10-07kbuild: deb-pkg: Remove blank first line from maint scriptsAaron Thompson1-1/+0
The blank line causes execve() to fail: # strace ./postinst execve("./postinst", ...) = -1 ENOEXEC (Exec format error) strace: exec: Exec format error +++ exited with 1 +++ However running the scripts via shell does work (at least with bash) because the shell attempts to execute the file as a shell script when execve() fails. Fixes: b611daae5efc ("kbuild: deb-pkg: split image and debug objects staging out into functions") Signed-off-by: Aaron Thompson <[email protected]> Reviewed-by: Nathan Chancellor <[email protected]> Reviewed-by: Nicolas Schier <[email protected]> Signed-off-by: Masahiro Yamada <[email protected]>
2024-10-07kbuild: fix a typo dt_binding_schema -> dt_binding_schemasXu Yang1-1/+1
If we follow "make help" to "make dt_binding_schema", we will see below error: $ make dt_binding_schema make[1]: *** No rule to make target 'dt_binding_schema'. Stop. make: *** [Makefile:224: __sub-make] Error 2 It should be a typo. So this will fix it. Fixes: 604a57ba9781 ("dt-bindings: kbuild: Add separate target/dependency for processed-schema.json") Signed-off-by: Xu Yang <[email protected]> Reviewed-by: Nicolas Schier <[email protected]> Signed-off-by: Masahiro Yamada <[email protected]>
2024-10-07scripts: import more list macrosSami Tolvanen1-0/+50
Import list_is_first, list_is_last, list_replace, and list_replace_init. Signed-off-by: Sami Tolvanen <[email protected]> Signed-off-by: Masahiro Yamada <[email protected]>
2024-10-06platform/x86: x86-android-tablets: Fix use after free on ↵Hans de Goede1-2/+4
platform_device_register() errors x86_android_tablet_remove() frees the pdevs[] array, so it should not be used after calling x86_android_tablet_remove(). When platform_device_register() fails, store the pdevs[x] PTR_ERR() value into the local ret variable before calling x86_android_tablet_remove() to avoid using pdevs[] after it has been freed. Fixes: 5eba0141206e ("platform/x86: x86-android-tablets: Add support for instantiating platform-devs") Fixes: e2200d3f26da ("platform/x86: x86-android-tablets: Add gpio_keys support to x86_android_tablet_init()") Cc: [email protected] Reported-by: Aleksandr Burakov <[email protected]> Closes: https://lore.kernel.org/platform-driver-x86/[email protected]/ Signed-off-by: Hans de Goede <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2024-10-06platform/x86: wmi: Update WMI driver API documentationArmin Wolf1-6/+5
The WMI driver core now passes the WMI event data to legacy notify handlers, so WMI devices sharing notification IDs are now being handled properly. Fixes: e04e2b760ddb ("platform/x86: wmi: Pass event data directly to legacy notify handlers") Signed-off-by: Armin Wolf <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Hans de Goede <[email protected]>
2024-10-06platform/x86: dell-ddv: Fix typo in documentationAnaswara T Rajan1-2/+2
Fix typo in word 'diagnostics' in documentation. Signed-off-by: Anaswara T Rajan <[email protected]> Reviewed-by: Armin Wolf <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Hans de Goede <[email protected]>
2024-10-06platform/x86: dell-sysman: add support for alienware productsCrag Wang1-0/+1
Alienware supports firmware-attributes and has its own OEM string. Signed-off-by: Crag Wang <[email protected]> Link: https://lore.kernel.org/r/[email protected] Reviewed-by: Hans de Goede <[email protected]> Signed-off-by: Hans de Goede <[email protected]>
2024-10-06platform/x86/intel: power-domains: Add Diamond Rapids supportSrinivas Pandruvada1-0/+1
Add Diamond Rapids (INTEL_PANTHERCOVE_X) to tpmi_cpu_ids to support domaid id mappings. Signed-off-by: Srinivas Pandruvada <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Hans de Goede <[email protected]>
2024-10-06platform/x86: ISST: Add Diamond Rapids to support listSrinivas Pandruvada1-0/+1
Add Diamond Rapids (INTEL_PANTHERCOVE_X) to SST support list by adding to isst_cpu_ids. Signed-off-by: Srinivas Pandruvada <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Hans de Goede <[email protected]>
2024-10-06platform/x86:intel/pmc: Disable ACPI PM Timer disabling on Sky and Kaby LakeHans de Goede1-2/+0
There have been multiple reports that the ACPI PM Timer disabling is causing Sky and Kaby Lake systems to hang on all suspend (s2idle, s3, hibernate) methods. Remove the acpi_pm_tmr_ctl_offset and acpi_pm_tmr_disable_bit settings from spt_reg_map to disable the ACPI PM Timer disabling on Sky and Kaby Lake to fix the hang on suspend. Fixes: e86c8186d03a ("platform/x86:intel/pmc: Enable the ACPI PM Timer to be turned off when suspended") Reported-by: Paul Menzel <[email protected]> Closes: https://lore.kernel.org/linux-pm/[email protected]/ Reported-by: Todd Brandt <[email protected]> Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219346 Cc: Marek Maslanka <[email protected]> Signed-off-by: Hans de Goede <[email protected]> Tested-by: Todd Brandt <[email protected]> Tested-by: Paul Menzel <[email protected]> # Dell XPS 13 9360/0596KF Acked-by: Rafael J. Wysocki <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2024-10-06platform/x86: dell-laptop: Do not fail when encountering unsupported batteriesArmin Wolf1-3/+12
If the battery hook encounters a unsupported battery, it will return an error. This in turn will cause the battery driver to automatically unregister the battery hook. On machines with multiple batteries however, this will prevent the battery hook from handling the primary battery, since it will always get unregistered upon encountering one of the unsupported batteries. Fix this by simply ignoring unsupported batteries. Reviewed-by: Pali Rohár <[email protected]> Fixes: ab58016c68cc ("platform/x86:dell-laptop: Add knobs to change battery charge settings") Signed-off-by: Armin Wolf <[email protected]> Link: https://lore.kernel.org/r/[email protected] Reviewed-by: Hans de Goede <[email protected]> Signed-off-by: Hans de Goede <[email protected]>
2024-10-06MAINTAINERS: Update Intel In Field Scan(IFS) entryJithu Joseph1-1/+1
Ashok is no longer with Intel and his e-mail address will start bouncing soon. Update his email address to the new one he provided to ensure correct contact details in the MAINTAINERS file. Signed-off-by: Jithu Joseph <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Hans de Goede <[email protected]>
2024-10-06Merge tag 'kvmarm-fixes-6.12-1' of ↵Paolo Bonzini11365-188892/+449653
git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD KVM/arm64 fixes for 6.12, take #1 - Fix pKVM error path on init, making sure we do not change critical system registers as we're about to fail - Make sure that the host's vector length is at capped by a value common to all CPUs - Fix kvm_has_feat*() handling of "negative" features, as the current code is pretty broken - Promote Joey to the status of official reviewer, while James steps down -- hopefully only temporarly
2024-10-06x86/reboot: emergency callbacks are now registered by common KVM codePaolo Bonzini2-4/+4
Guard them with CONFIG_KVM_X86_COMMON rather than the two vendor modules. In practice this has no functional change, because CONFIG_KVM_X86_COMMON is set if and only if at least one vendor-specific module is being built. However, it is cleaner to specify CONFIG_KVM_X86_COMMON for functions that are used in kvm.ko. Reported-by: Linus Torvalds <[email protected]> Fixes: 590b09b1d88e ("KVM: x86: Register "emergency disable" callbacks when virt is enabled") Fixes: 6d55a94222db ("x86/reboot: Unconditionally define cpu_emergency_virt_cb typedef") Signed-off-by: Paolo Bonzini <[email protected]>
2024-10-06KVM: x86: leave kvm.ko out of the build if no vendor module is requestedPaolo Bonzini2-4/+7
kvm.ko is nothing but library code shared by kvm-intel.ko and kvm-amd.ko. It provides no functionality on its own and it is unnecessary unless one of the vendor-specific module is compiled. In particular, /dev/kvm is not created until one of kvm-intel.ko or kvm-amd.ko is loaded. Use CONFIG_KVM to decide if it is built-in or a module, but use the vendor-specific modules for the actual decision on whether to build it. This also fixes a build failure when CONFIG_KVM_INTEL and CONFIG_KVM_AMD are both disabled. The cpu_emergency_register_virt_callback() function is called from kvm.ko, but it is only defined if at least one of CONFIG_KVM_INTEL and CONFIG_KVM_AMD is provided. Fixes: 590b09b1d88e ("KVM: x86: Register "emergency disable" callbacks when virt is enabled") Signed-off-by: Paolo Bonzini <[email protected]>
2024-10-05Merge tag 'bcachefs-2024-10-05' of git://evilpiepirate.org/bcachefsLinus Torvalds20-209/+342
Pull bcachefs fixes from Kent Overstreet: "A lot of little fixes, bigger ones include: - bcachefs's __wait_on_freeing_inode() was broken in rc1 due to vfs changes, now fixed along with another lost wakeup - fragmentation LRU fixes; fsck now repairs successfully (this is the data structure copygc uses); along with some nice simplification. - Rework logged op error handling, so that if logged op replay errors (due to another filesystem error) we delete the logged op instead of going into an infinite loop) - Various small filesystem connectivitity repair fixes" * tag 'bcachefs-2024-10-05' of git://evilpiepirate.org/bcachefs: bcachefs: Rework logged op error handling bcachefs: Add warn param to subvol_get_snapshot, peek_inode bcachefs: Kill snapshot arg to fsck_write_inode() bcachefs: Check for unlinked, non-empty dirs in check_inode() bcachefs: Check for unlinked inodes with dirents bcachefs: Check for directories with no backpointers bcachefs: Kill alloc_v4.fragmentation_lru bcachefs: minor lru fsck fixes bcachefs: Mark more errors AUTOFIX bcachefs: Make sure we print error that causes fsck to bail out bcachefs: bkey errors are only AUTOFIX during read bcachefs: Create lost+found in correct snapshot bcachefs: Fix reattach_inode() bcachefs: Add missing wakeup to bch2_inode_hash_remove() bcachefs: Fix trans_commit disk accounting revert bcachefs: Fix bch2_inode_is_open() check bcachefs: Fix return type of dirent_points_to_inode_nowarn() bcachefs: Fix bad shift in bch2_read_flag_list()
2024-10-05Merge tag 'for-linus-6.12a-rc2-tag' of ↵Linus Torvalds1-1/+1
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip Pull xen fix from Juergen Gross: "Fix Xen config issue introduced in the merge window" * tag 'for-linus-6.12a-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: xen: Fix config option reference in XEN_PRIVCMD definition
2024-10-05Merge tag 'ext4_for_linus-5.12-rc2' of ↵Linus Torvalds3-17/+23
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4 Pull ext4 fixes from Ted Ts'o: "Fix some ext4 bugs and regressions relating to oneline resize and fast commits" * tag 'ext4_for_linus-5.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: ext4: fix off by one issue in alloc_flex_gd() ext4: mark fc as ineligible using an handle in ext4_xattr_set() ext4: use handle to mark fc as ineligible in __track_dentry_update()
Powered by cgit, Gruvboxed by Blaster4385.