Age | Commit message (Collapse) | Author | Files | Lines |
|
Currently, when NFSD handles an asynchronous COPY, it returns a
zero write verifier, relying on the subsequent CB_OFFLOAD callback
to pass the write verifier and a stable_how4 value to the client.
However, if the CB_OFFLOAD never arrives at the client (for example,
if a network partition occurs just as the server sends the
CB_OFFLOAD operation), the client will never receive this verifier.
Thus, if the client sends a follow-up COMMIT, there is no way for
the client to assess the COMMIT result.
The usual recovery for a missing CB_OFFLOAD is for the client to
send an OFFLOAD_STATUS operation, but that operation does not carry
a write verifier in its result. Neither does it carry a stable_how4
value, so the client /must/ send a COMMIT in this case -- which will
always fail because currently there's still no write verifier in the
COPY result.
Thus the server needs to return a normal write verifier in its COPY
result even if the COPY operation is to be performed asynchronously.
If the server recognizes the callback stateid in subsequent
OFFLOAD_STATUS operations, then obviously it has not restarted, and
the write verifier the client received in the COPY result is still
valid and can be used to assess a COMMIT of the copied data, if one
is needed.
Reviewed-by: Jeff Layton <[email protected]>
Signed-off-by: Chuck Lever <[email protected]>
|
|
wake_up_var() needs a barrier after the important change is made in the
var and before wake_up_var() is called, else it is possible that a wake
up won't be sent when it should.
In each case here the var is changed in an "atomic" manner, so
smb_mb__after_atomic() is sufficient.
In one case the important change (removing the lease) is performed
*after* the wake_up, which is backwards. The code survives in part
because the wait_var_event is given a timeout.
This patch adds the required barriers and calls destroy_delegation()
*before* waking any threads waiting for the delegation to be destroyed.
Signed-off-by: NeilBrown <[email protected]>
Reviewed-by: Jeff Layton <[email protected]>
Signed-off-by: Chuck Lever <[email protected]>
|
|
nfsd has two places that open-code clear_and_wake_up_bit(). One has
the required memory barriers. The other does not.
Change both to use clear_and_wake_up_bit() so we have the barriers
without the noise.
Signed-off-by: NeilBrown <[email protected]>
Reviewed-by: Jeff Layton <[email protected]>
Signed-off-by: Chuck Lever <[email protected]>
|
|
Using ERR_CAST() is more reasonable and safer, When it is necessary
to convert the type of an error pointer and return it.
Signed-off-by: Yan Zhen <[email protected]>
Signed-off-by: Chuck Lever <[email protected]>
|
|
Add the __counted_by compiler attribute to the flexible array member
volumes to improve access bounds-checking via CONFIG_UBSAN_BOUNDS and
CONFIG_FORTIFY_SOURCE.
Use struct_size() instead of manually calculating the number of bytes to
allocate for a pnfs_block_deviceaddr with a single volume.
Signed-off-by: Thorsten Blum <[email protected]>
Reviewed-by: Gustavo A. R. Silva <[email protected]>
Acked-by: Jeff Layton <[email protected]>
Signed-off-by: Chuck Lever <[email protected]>
|
|
If not enough buffer space available, but idmap_lookup has triggered
lookup_fn which calls cache_get and returns successfully. Then we
missed to call cache_put here which pairs with cache_get.
Fixes: ddd1ea563672 ("nfsd4: use xdr_reserve_space in attribute encoding")
Signed-off-by: Guoqing Jiang <[email protected]>
Reviwed-by: Jeff Layton <[email protected]>
Signed-off-by: Chuck Lever <[email protected]>
|
|
Add some tracepoints in the callback client RPC operations. Also
add a tracepoint to nfsd4_cb_getattr_done.
Signed-off-by: Jeff Layton <[email protected]>
Signed-off-by: Chuck Lever <[email protected]>
|
|
Keep track of the "main" opcode for the callback, and display it in the
tracepoint. This makes it simpler to discern what's happening when there
is more than one callback in flight.
The one special case is the CB_NULL RPC. That's not a CB_COMPOUND
opcode, so designate the value 0 for that.
Signed-off-by: Jeff Layton <[email protected]>
Signed-off-by: Chuck Lever <[email protected]>
|
|
Currently, you get the warning and stack trace, but nothing is printed
about the relevant error codes. Add that in.
Signed-off-by: Jeff Layton <[email protected]>
Signed-off-by: Chuck Lever <[email protected]>
|
|
Fix spelling errors in comments of nfsd4_release_lockowner and
nfs4_set_delegation.
Signed-off-by: Li Lingfeng <[email protected]>
Signed-off-by: Chuck Lever <[email protected]>
|
|
Commit 427f5f83a319 ("NFSD: Ensure nf_inode is never dereferenced") passes
inode directly to nfsd_file_mark_find_or_create instead of getting it from
nf, so there is no need to pass nf.
Signed-off-by: Li Lingfeng <[email protected]>
Reviewed-by: Jeff Layton <[email protected]>
Signed-off-by: Chuck Lever <[email protected]>
|
|
list_head can be initialized automatically with LIST_HEAD()
instead of calling INIT_LIST_HEAD().
Signed-off-by: Hongbo Li <[email protected]>
Signed-off-by: Chuck Lever <[email protected]>
|
|
Ext4 will throw -EBADMSG through ext4_readdir when a checksum error
occurs, resulting in the following WARNING.
Fix it by mapping EBADMSG to nfserr_io.
nfsd_buffered_readdir
iterate_dir // -EBADMSG -74
ext4_readdir // .iterate_shared
ext4_dx_readdir
ext4_htree_fill_tree
htree_dirblock_to_tree
ext4_read_dirblock
__ext4_read_dirblock
ext4_dirblock_csum_verify
warn_no_space_for_csum
__warn_no_space_for_csum
return ERR_PTR(-EFSBADCRC) // -EBADMSG -74
nfserrno // WARNING
[ 161.115610] ------------[ cut here ]------------
[ 161.116465] nfsd: non-standard errno: -74
[ 161.117315] WARNING: CPU: 1 PID: 780 at fs/nfsd/nfsproc.c:878 nfserrno+0x9d/0xd0
[ 161.118596] Modules linked in:
[ 161.119243] CPU: 1 PID: 780 Comm: nfsd Not tainted 5.10.0-00014-g79679361fd5d #138
[ 161.120684] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qe
mu.org 04/01/2014
[ 161.123601] RIP: 0010:nfserrno+0x9d/0xd0
[ 161.124676] Code: 0f 87 da 30 dd 00 83 e3 01 b8 00 00 00 05 75 d7 44 89 ee 48 c7 c7 c0 57 24 98 89 44 24 04 c6
05 ce 2b 61 03 01 e8 99 20 d8 00 <0f> 0b 8b 44 24 04 eb b5 4c 89 e6 48 c7 c7 a0 6d a4 99 e8 cc 15 33
[ 161.127797] RSP: 0018:ffffc90000e2f9c0 EFLAGS: 00010286
[ 161.128794] RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
[ 161.130089] RDX: 1ffff1103ee16f6d RSI: 0000000000000008 RDI: fffff520001c5f2a
[ 161.131379] RBP: 0000000000000022 R08: 0000000000000001 R09: ffff8881f70c1827
[ 161.132664] R10: ffffed103ee18304 R11: 0000000000000001 R12: 0000000000000021
[ 161.133949] R13: 00000000ffffffb6 R14: ffff8881317c0000 R15: ffffc90000e2fbd8
[ 161.135244] FS: 0000000000000000(0000) GS:ffff8881f7080000(0000) knlGS:0000000000000000
[ 161.136695] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 161.137761] CR2: 00007fcaad70b348 CR3: 0000000144256006 CR4: 0000000000770ee0
[ 161.139041] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 161.140291] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 161.141519] PKRU: 55555554
[ 161.142076] Call Trace:
[ 161.142575] ? __warn+0x9b/0x140
[ 161.143229] ? nfserrno+0x9d/0xd0
[ 161.143872] ? report_bug+0x125/0x150
[ 161.144595] ? handle_bug+0x41/0x90
[ 161.145284] ? exc_invalid_op+0x14/0x70
[ 161.146009] ? asm_exc_invalid_op+0x12/0x20
[ 161.146816] ? nfserrno+0x9d/0xd0
[ 161.147487] nfsd_buffered_readdir+0x28b/0x2b0
[ 161.148333] ? nfsd4_encode_dirent_fattr+0x380/0x380
[ 161.149258] ? nfsd_buffered_filldir+0xf0/0xf0
[ 161.150093] ? wait_for_concurrent_writes+0x170/0x170
[ 161.151004] ? generic_file_llseek_size+0x48/0x160
[ 161.151895] nfsd_readdir+0x132/0x190
[ 161.152606] ? nfsd4_encode_dirent_fattr+0x380/0x380
[ 161.153516] ? nfsd_unlink+0x380/0x380
[ 161.154256] ? override_creds+0x45/0x60
[ 161.155006] nfsd4_encode_readdir+0x21a/0x3d0
[ 161.155850] ? nfsd4_encode_readlink+0x210/0x210
[ 161.156731] ? write_bytes_to_xdr_buf+0x97/0xe0
[ 161.157598] ? __write_bytes_to_xdr_buf+0xd0/0xd0
[ 161.158494] ? lock_downgrade+0x90/0x90
[ 161.159232] ? nfs4svc_decode_voidarg+0x10/0x10
[ 161.160092] nfsd4_encode_operation+0x15a/0x440
[ 161.160959] nfsd4_proc_compound+0x718/0xe90
[ 161.161818] nfsd_dispatch+0x18e/0x2c0
[ 161.162586] svc_process_common+0x786/0xc50
[ 161.163403] ? nfsd_svc+0x380/0x380
[ 161.164137] ? svc_printk+0x160/0x160
[ 161.164846] ? svc_xprt_do_enqueue.part.0+0x365/0x380
[ 161.165808] ? nfsd_svc+0x380/0x380
[ 161.166523] ? rcu_is_watching+0x23/0x40
[ 161.167309] svc_process+0x1a5/0x200
[ 161.168019] nfsd+0x1f5/0x380
[ 161.168663] ? nfsd_shutdown_threads+0x260/0x260
[ 161.169554] kthread+0x1c4/0x210
[ 161.170224] ? kthread_insert_work_sanity_check+0x80/0x80
[ 161.171246] ret_from_fork+0x1f/0x30
Signed-off-by: Li Lingfeng <[email protected]>
Reviewed-by: Jeff Layton <[email protected]>
Cc: [email protected]
Signed-off-by: Chuck Lever <[email protected]>
|
|
Commit 5826e09bf3dd ("NFSD: OP_CB_RECALL_ANY should recall both read and
write delegations") added a new assignment statement to add
RCA4_TYPE_MASK_WDATA_DLG to ra_bmval bitmask of OP_CB_RECALL_ANY. So the
old one should be removed.
Signed-off-by: Li Lingfeng <[email protected]>
Reviewed-by: Jeff Layton <[email protected]>
Signed-off-by: Chuck Lever <[email protected]>
|
|
Collect a few very old previous employers as well.
Signed-off-by: Chuck Lever <[email protected]>
|
|
According to RFC 8881, all minor versions of NFSv4 support PUTPUBFH.
Replace the XDR decoder for PUTPUBFH with a "noop" since we no
longer want the minorversion check, and PUTPUBFH has no arguments to
decode. (Ideally nfsd4_decode_noop should really be called
nfsd4_decode_void).
PUTPUBFH should now behave just like PUTROOTFH.
Reported-by: Cedric Blancher <[email protected]>
Fixes: e1a90ebd8b23 ("NFSD: Combine decode operations for v4 and v4.1")
Cc: Dan Shelton <[email protected]>
Cc: Roland Mainz <[email protected]>
Cc: [email protected]
Signed-off-by: Chuck Lever <[email protected]>
|
|
The 'callback address' in client_info_show is output without quotes
causing yaml parsers to fail on processing IPv6 addresses.
Adding quotes to 'callback address' also matches that used by
the 'address' field.
Signed-off-by: Mark Grimes <[email protected]>
Reviewed-by: Jeff Layton <[email protected]>
Reviewed-by: NeilBrown <[email protected]>
Signed-off-by: Chuck Lever <[email protected]>
|
|
Synchronously wait for all disconnects to complete to ensure the
transports have divested all hardware resources before the
underlying RDMA device can safely be removed.
Reviewed-by: Sagi Grimberg <[email protected]>
Signed-off-by: Chuck Lever <[email protected]>
|
|
If an NFS operation expects a particular sort of object (file, dir, link,
etc) but gets a file handle for a different sort of object, it must
return an error. The actual error varies among NFS versions in non-trivial
ways.
For v2 and v3 there are ISDIR and NOTDIR errors and, for NFSv4 only,
INVAL is suitable.
For v4.0 there is also NFS4ERR_SYMLINK which should be used if a SYMLINK
was found when not expected. This take precedence over NOTDIR.
For v4.1+ there is also NFS4ERR_WRONG_TYPE which should be used in
preference to EINVAL when none of the specific error codes apply.
When nfsd_mode_check() finds a symlink where it expected a directory it
needs to return an error code that can be converted to NOTDIR for v2 or
v3 but will be SYMLINK for v4. It must be different from the error
code returns when it finds a symlink but expects a regular file - that
must be converted to EINVAL or SYMLINK.
So we introduce an internal error code nfserr_symlink_not_dir which each
version converts as appropriate.
nfsd_check_obj_isreg() is similar to nfsd_mode_check() except that it is
only used by NFSv4 and only for OPEN. NFSERR_INVAL is never a suitable
error if the object is the wrong time. For v4.0 we use nfserr_symlink
for non-dirs even if not a symlink. For v4.1 we have nfserr_wrong_type.
We handle this difference in-place in nfsd_check_obj_isreg() as there is
nothing to be gained by delaying the choice to nfsd4_map_status().
As a result of these changes, nfsd_mode_check() doesn't need an rqstp
arg any more.
Note that NFSv4 operations are actually performed in the xdr code(!!!)
so to the only place that we can map the status code successfully is in
nfsd4_encode_operation().
Signed-off-by: NeilBrown <[email protected]>
Reviewed-by: Jeff Layton <[email protected]>
Signed-off-by: Chuck Lever <[email protected]>
|
|
Rather than using ad hoc values for internal errors (30000, 11000, ...)
use 'enum' to sequentially allocate numbers starting from the first
known available number - now visible as NFS4ERR_FIRST_FREE.
The goal is values that are distinct from all be32 error codes. To get
those we must first select integers that are not already used, then
convert them with cpu_to_be32().
Signed-off-by: NeilBrown <[email protected]>
Reviewed-by: Jeff Layton <[email protected]>
Reviewed-by: Christoph Hellwig <[email protected]>
Signed-off-by: Chuck Lever <[email protected]>
|
|
There is code scattered around nfsd which chooses an error status based
on the particular version of nfs being used. It is cleaner to have the
version specific choices in version specific code.
With this patch common code returns the most specific error code
possible and the version specific code maps that if necessary.
Both v2 (nfsproc.c) and v3 (nfs3proc.c) now have a "map_status()"
function which is called to map the resp->status before each non-trivial
nfsd_proc_* or nfsd3_proc_* function returns.
NFS4ERR_SYMLINK and NFS4ERR_WRONG_TYPE introduce extra complications and
are left for a later patch.
Signed-off-by: NeilBrown <[email protected]>
Reviewed-by: Jeff Layton <[email protected]>
Reviewed-by: Christoph Hellwig <[email protected]>
Signed-off-by: Chuck Lever <[email protected]>
|
|
This further centralizes version number checks.
Signed-off-by: NeilBrown <[email protected]>
Reviewed-by: Jeff Layton <[email protected]>
Signed-off-by: Chuck Lever <[email protected]>
|
|
With this patch the only places that test ->rq_vers against a specific
version are nfsd_v4client() and nfsd_set_fh_dentry().
The latter sets some flags in the svc_fh, which now includes:
fh_64bit_cookies
fh_use_wgather
Signed-off-by: NeilBrown <[email protected]>
Reviewed-by: Jeff Layton <[email protected]>
Signed-off-by: Chuck Lever <[email protected]>
|
|
nfsd_breaker_owns_lease() currently open-codes the same test that
nfsd_v4client() performs.
With this patch we use nfsd_v4client() instead.
Also as i_am_nfsd() is only used in combination with kthread_data(),
replace it with nfsd_current_rqst() which combines the two and returns a
valid svc_rqst, or NULL.
The test for NULL is moved into nfsd_v4client() for code clarity.
Signed-off-by: NeilBrown <[email protected]>
Reviewed-by: Jeff Layton <[email protected]>
Signed-off-by: Chuck Lever <[email protected]>
|
|
nfsd_permission(), exp_rdonly(), nfsd_setuser(), and nfsexp_flags()
only ever need the cred out of rqstp, so pass it explicitly instead of
the whole rqstp.
This makes the interfaces cleaner.
Signed-off-by: NeilBrown <[email protected]>
Reviewed-by: Jeff Layton <[email protected]>
Signed-off-by: Chuck Lever <[email protected]>
|
|
Rather than passing the whole rqst, pass the pieces that are actually
needed. This makes the inputs to rqst_exp_find() more obvious.
Signed-off-by: NeilBrown <[email protected]>
Reviewed-by: Jeff Layton <[email protected]>
Signed-off-by: Chuck Lever <[email protected]>
|
|
Move the stateid handling to nfsd4_copy_notify.
If nfs4_preprocess_stateid_op did not produce an output stateid, error out.
Copy notify specifically does not permit the use of special stateids,
so enforce that outside generic stateid pre-processing.
Signed-off-by: Sagi Grimberg <[email protected]>
Reviewed-by: Jeff Layton <[email protected]>
Reviewed-by: Olga Kornievskaia <[email protected]>
Signed-off-by: Chuck Lever <[email protected]>
|
|
If an svc thread needs to perform some initialisation that might fail,
it has no good way to handle the failure.
Before the thread can exit it must call svc_exit_thread(), but that
requires the service mutex to be held. The thread cannot simply take
the mutex as that could deadlock if there is a concurrent attempt to
shut down all threads (which is unlikely, but not impossible).
nfsd currently call svc_exit_thread() unprotected in the unlikely event
that unshare_fs_struct() fails.
We can clean this up by introducing svc_thread_init_status() by which an
svc thread can report whether initialisation has succeeded. If it has,
it continues normally into the action loop. If it has not,
svc_thread_init_status() immediately aborts the thread.
svc_start_kthread() waits for either of these to happen, and calls
svc_exit_thread() (under the mutex) if the thread aborted.
Signed-off-by: NeilBrown <[email protected]>
Reviewed-by: Jeff Layton <[email protected]>
Signed-off-by: Chuck Lever <[email protected]>
|
|
The only caller of svc_rqst_alloc() is svc_prepare_thread(). So merge
the one into the other and simplify.
Signed-off-by: NeilBrown <[email protected]>
Reviewed-by: Jeff Layton <[email protected]>
Signed-off-by: Chuck Lever <[email protected]>
|
|
As documented in svc_xprt.c, sv_nrthreads is protected by the service
mutex, and it does not need ->sv_lock.
(->sv_lock is needed only for sv_permsocks, sv_tempsocks, and
sv_tmpcnt).
So remove the unnecessary locking.
Signed-off-by: NeilBrown <[email protected]>
Signed-off-by: Chuck Lever <[email protected]>
|
|
sp_nrthreads is only ever accessed under the service mutex
nlmsvc_mutex nfs_callback_mutex nfsd_mutex
so these is no need for it to be an atomic_t.
The fact that all code using it is single-threaded means that we can
simplify svc_pool_victim and remove the temporary elevation of
sp_nrthreads.
Signed-off-by: NeilBrown <[email protected]>
Signed-off-by: Chuck Lever <[email protected]>
|
|
The locking required for svc_exit_thread() is not obvious, so document
it in a kdoc comment.
Signed-off-by: NeilBrown <[email protected]>
Reviewed-by: Jeff Layton <[email protected]>
Signed-off-by: Chuck Lever <[email protected]>
|
|
Instead of using kmalloc to allocate an array for storing active version
info, just declare an array to the max size - it is only 5 or so.
Signed-off-by: NeilBrown <[email protected]>
Signed-off-by: Chuck Lever <[email protected]>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Borislav Petkov:
- Remove percpu irq related code in the timer-of initialization routine
as it is broken but also unused (Daniel Lezcano)
- Fix return -ETIME when delta exceeds INT_MAX and the next event not
taking effect sometimes (Jacky Bai)
* tag 'timers_urgent_for_v6.11_rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/drivers/imx-tpm: Fix next event not taking effect sometime
clocksource/drivers/imx-tpm: Fix return -ETIME when delta exceeds INT_MAX
clocksource/drivers/timer-of: Remove percpu irq related code
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Borislav Petkov:
- Fix perf's AUX buffer serialization
- Prevent uninitialized struct members in perf's uprobes handling
* tag 'perf_urgent_for_v6.11_rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/aux: Fix AUX buffer serialization
uprobes: Use kzalloc to allocate xol area
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some small char/misc/other driver fixes for 6.11-rc7. It's
nothing huge, just a bunch of small fixes of reported problems,
including:
- lots of tiny iio driver fixes
- nvmem driver fixex
- binder UAF bugfix
- uio driver crash fix
- other small fixes
All of these have been in linux-next this week with no reported
problems"
* tag 'char-misc-6.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (21 commits)
VMCI: Fix use-after-free when removing resource in vmci_resource_remove()
Drivers: hv: vmbus: Fix rescind handling in uio_hv_generic
uio_hv_generic: Fix kernel NULL pointer dereference in hv_uio_rescind
misc: keba: Fix sysfs group creation
dt-bindings: nvmem: Use soc-nvmem node name instead of nvmem
nvmem: Fix return type of devm_nvmem_device_get() in kerneldoc
nvmem: u-boot-env: error if NVMEM device is too small
misc: fastrpc: Fix double free of 'buf' in error path
binder: fix UAF caused by offsets overwrite
iio: imu: inv_mpu6050: fix interrupt status read for old buggy chips
iio: adc: ad7173: fix GPIO device info
iio: adc: ad7124: fix DT configuration parsing
iio: adc: ad_sigma_delta: fix irq_flags on irq request
iio: adc: ads1119: Fix IRQ flags
iio: fix scale application in iio_convert_raw_to_processed_unlocked
iio: adc: ad7124: fix config comparison
iio: adc: ad7124: fix chip ID mismatch
iio: adc: ad7173: Fix incorrect compatible string
iio: buffer-dmaengine: fix releasing dma channel on error
iio: adc: ad7606: remove frstdata check for serial mode
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a handful of small USB fixes for 6.11-rc7. Included in here
are:
- dwc3 driver fixes for two reported problems
- two typec ucsi driver fixes
- cdns2 controller reset fix
All of these have been in linux-next this week with no reported
problems"
* tag 'usb-6.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: typec: ucsi: Fix cable registration
usb: typec: ucsi: Fix the partner PD revision
usb: cdns2: Fix controller reset issue
usb: dwc3: core: update LC timer as per USB Spec V3.2
usb: dwc3: Avoid waking up gadget during startxfer
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A pile of Qualcomm clk driver fixes with two main themes: the alpha
PLL driver and shared RCGs, and one fix for the Starfive JH7110 SoC.
- The Alpha PLL clk_ops had multiple problems around setting rates.
There are a handful of patches here that fix masks and skip
enabling the clk from set_rate() when the PLL is disabled. The PLLs
are crucial to operation of the system as almost all frequencies in
the system are derived from them.
- Parking shared RCGs at a slow always on clk at registration time
breaks stuff.
USB host mode can't handle such a slow frequency and the serial
console gets all garbled when the UART clk is handed over to the
kernel. There's a few patches that don't use the shared clk_ops for
the UART clks and another one to skip parking the USB clk at
registration time.
- The Starfive PLL driver used for the CPU was busted causing cpufreq
to fail because the clk didn't change to a safe parent during
set_rate().
The fix is to register a notifier and switch to a safe parent so
the PLL can change rate in a glitch free manner"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: qcom: gcc-sc8280xp: don't use parking clk_ops for QUPs
clk: starfive: jh7110-sys: Add notifier for PLL0 clock
clk: qcom: gcc-sm8650: Don't use shared clk_ops for QUPs
clk: qcom: gcc-sm8550: Don't park the USB RCG at registration time
clk: qcom: gcc-sm8550: Don't use parking clk_ops for QUPs
clk: qcom: gcc-x1e80100: Don't use parking clk_ops for QUPs
clk: qcom: ipq9574: Update the alpha PLL type for GPLLs
clk: qcom: gcc-x1e80100: Fix USB 0 and 1 PHY GDSC pwrsts flags
clk: qcom: clk-alpha-pll: Update set_rate for Zonda PLL
clk: qcom: clk-alpha-pll: Fix zonda set_rate failure when PLL is disabled
clk: qcom: clk-alpha-pll: Fix the trion pll postdiv set rate API
clk: qcom: clk-alpha-pll: Fix the pll post div mask
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fix from James Bottomley:
"Single ufs driver fix quirking around another device spec violation"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: ufs-mediatek: Add UFSHCD_QUIRK_BROKEN_LSDBS_CAP
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fix from Linus Walleij:
"A single fix for Qualcomm laptops that are affected by
missing wakeup IRQs"
* tag 'pinctrl-v6.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: qcom: x1e80100: Bypass PDC wakeup parent for now
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
PullKUnit fix from Shuah Khan:
"Fix to a missing function parameter warning found during documentation
build in linux-next"
* tag 'linux_kselftest-kunit-fixes-6.11-rc7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
kunit: Fix missing kerneldoc comment
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci fixes from Bjorn Helgaas:
- Unregister platform devices for child nodes when stopping a PCI
device, even if the PCI core has already cleared the OF_POPULATED bit
and of_platform_depopulate() doesn't do anything (Bartosz
Golaszewski)
- Rescan the bus from a separate thread so we don't deadlock when
triggering rescan from sysfs (Bartosz Golaszewski)
* tag 'pci-v6.11-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
PCI/pwrctl: Rescan bus on a separate thread
PCI: Don't rely on of_platform_depopulate() for reused OF-nodes
|
|
Pull smb client fixes from Steve French:
- fix potential mount hang
- fix retry problem in two types of compound operations
- important netfs integration fix in SMB1 read paths
- fix potential uninitialized zero point of inode
- minor patch to improve debugging for potential crediting problems
* tag 'v6.11-rc6-cifs-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
netfs, cifs: Improve some debugging bits
cifs: Fix SMB1 readv/writev callback in the same way as SMB2/3
cifs: Fix zero_point init on inode initialisation
smb: client: fix double put of @cfile in smb2_set_path_size()
smb: client: fix double put of @cfile in smb2_rename_path()
smb: client: fix hang in wait_for_response() for negproto
|
|
clang warns on this because it has an unannotated fall-through between
cases:
arch/x86/kvm/x86.c:4819:2: error: unannotated fall-through between switch labels [-Werror,-Wimplicit-fallthrough]
and while we could annotate it as a fallthrough, the proper fix is to
just add the break for this case, instead of falling through to the
default case and the break there.
gcc also has that warning, but it looks like gcc only warns for the
cases where they fall through to "real code", rather than to just a
break. Odd.
Fixes: d30d9ee94cc0 ("KVM: x86: Only advertise KVM_CAP_READONLY_MEM when supported by VM")
Cc: Paolo Bonzini <[email protected]>
Cc: Tom Dohrmann <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fix from Catalin Marinas:
"Fix the arm64 usage of ftrace_graph_ret_addr() to pass the
&state->graph_idx pointer instead of NULL, otherwise this function
just returns early"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: stacktrace: fix the usage of ftrace_graph_ret_addr()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
- A revert for the mmap() change that ties the allocation range to the
hint adress, as what we tried to do ended up regressing on other
userspace workloads.
- A fix to avoid a kernel memory leak when emulating misaligned
accesses from userspace.
- A Kconfig fix for toolchain vector detection, which now correctly
detects vector support on toolchains where the V extension depends on
the M extension.
- A fix to avoid failing the linear mapping bootmem bounds check on
NOMMU systems.
- A fix for early alternatives on relocatable kernels.
* tag 'riscv-for-linus-6.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: Fix RISCV_ALTERNATIVE_EARLY
riscv: Do not restrict memory size because of linear mapping on nommu
riscv: Fix toolchain vector detection
riscv: misaligned: Restrict user access to kernel memory
riscv: mm: Do not restrict mmap address based on hint
riscv: selftests: Remove mmap hint address checks
Revert "RISC-V: mm: Document mmap changes"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix a deadlock in the powerpc qspinlock MCS queue logic
- Fix the return type of pgd_val() to not truncate 64-bit PTEs on 85xx
- Allow the check for dynamic relocations in the VDSO to work correctly
- Make mmu_pte_psize static to fix a build error
Thanks to Christophe Leroy, Nysal Jan K.A., Nicholas Piggin, Geetika
Moolchandani, Jijo Varghese, and Vaishnavi Bhat.
* tag 'powerpc-6.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/qspinlock: Fix deadlock in MCS queue
powerpc/mm: Fix return type of pgd_val()
powerpc/vdso: Don't discard rela sections
powerpc/64e: Define mmu_pte_psize static
|
|
Pull x86 kvm fixes from Paolo Bonzini:
"Many small fixes that accumulated while I was on vacation...
- Fixup missed comments from the REMOVED_SPTE => FROZEN_SPTE rename
- Ensure a root is successfully loaded when pre-faulting SPTEs
- Grab kvm->srcu when handling KVM_SET_VCPU_EVENTS to guard against
accessing memslots if toggling SMM happens to force a VM-Exit
- Emulate MSR_{FS,GS}_BASE on SVM even though interception is always
disabled, so that KVM does the right thing if KVM's emulator
encounters {RD,WR}MSR
- Explicitly clear BUS_LOCK_DETECT from KVM's caps on AMD, as KVM
doesn't yet virtualize BUS_LOCK_DETECT on AMD
- Cleanup the help message for CONFIG_KVM_AMD_SEV, and call out that
KVM now supports SEV-SNP too
- Specialize return value of
KVM_CHECK_EXTENSION(KVM_CAP_READONLY_MEM), based on VM type
- Remove unnecessary dependency on CONFIG_HIGH_RES_TIMERS
- Note an RCU quiescent state on guest exit. This avoids a call to
rcu_core() if there was a grace period request while guest was
running"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: Remove HIGH_RES_TIMERS dependency
kvm: Note an RCU quiescent state on guest exit
KVM: x86: Only advertise KVM_CAP_READONLY_MEM when supported by VM
KVM: SEV: Update KVM_AMD_SEV Kconfig entry and mention SEV-SNP
KVM: SVM: Don't advertise Bus Lock Detect to guest if SVM support is missing
KVM: SVM: fix emulation of msr reads/writes of MSR_FS_BASE and MSR_GS_BASE
KVM: x86: Acquire kvm->srcu when handling KVM_SET_VCPU_EVENTS
KVM: x86/mmu: Check that root is valid/loaded when pre-faulting SPTEs
KVM: x86/mmu: Fixup comments missed by the REMOVED_SPTE=>FROZEN_SPTE rename
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fix from Rafael Wysocki:
"Fix an incorrect warning emitted by the amd-pstate driver on
processors that don't support X86_FEATURE_CPPC (Gautham Shenoy)"
* tag 'pm-6.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq/amd-pstate: Remove warning for X86_FEATURE_CPPC on certain Zen models
|