| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
{inet,ipv6}_gro_receive functions perform flush checks (ttl, flags,
iph->id, ...) against all packets in a loop. These flush checks are used in
all merging UDP and TCP flows.
These checks need to be done only once and only against the found p skb,
since they only affect flush and not same_flow.
This patch leverages correct network header offsets from the cb for both
outer and inner network headers - allowing these checks to be done only
once, in tcp_gro_receive and udp_gro_receive_segment. As a result,
NAPI_GRO_CB(p)->flush is not used at all. In addition, flush_id checks are
more declarative and contained in inet_gro_flush, thus removing the need
for flush_id in napi_gro_cb.
This results in less parsing code for non-loop flush tests for TCP and UDP
flows.
To make sure results are not within noise range - I've made netfilter drop
all TCP packets, and measured CPU performance in GRO (in this case GRO is
responsible for about 50% of the CPU utilization).
perf top while replaying 64 parallel IP/TCP streams merging in GRO:
(gro_receive_network_flush is compiled inline to tcp_gro_receive)
net-next:
6.94% [kernel] [k] inet_gro_receive
3.02% [kernel] [k] tcp_gro_receive
patch applied:
4.27% [kernel] [k] tcp_gro_receive
4.22% [kernel] [k] inet_gro_receive
perf top while replaying 64 parallel IP/IP/TCP streams merging in GRO (same
results for any encapsulation, in this case inet_gro_receive is top
offender in net-next)
net-next:
10.09% [kernel] [k] inet_gro_receive
2.08% [kernel] [k] tcp_gro_receive
patch applied:
6.97% [kernel] [k] inet_gro_receive
3.68% [kernel] [k] tcp_gro_receive
Signed-off-by: Richard Gobert <[email protected]>
Reviewed-by: Willem de Bruijn <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
This patch converts references of skb->network_header to napi_gro_cb's
network_offset and inner_network_offset.
Signed-off-by: Richard Gobert <[email protected]>
Reviewed-by: Willem de Bruijn <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
David Arinzon says:
====================
ENA driver changes May 2024
This patchset contains several misc and minor
changes to the ENA driver.
====================
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
For the purpose of obtaining better CPU utilization,
minimum rx moderation interval is set to 20 usec.
Signed-off-by: Osama Abboud <[email protected]>
Signed-off-by: David Arinzon <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
strscpy copies as much of the string as possible,
meaning that the destination string will be truncated
in case of no space. As this is a non-critical error in
our case, adding a debug level print for indication.
This patch also removes a -1 which was added to ensure
enough space for NUL, but strscpy destination string is
guaranteed to be NUL-terminted, therefore, the -1 is
not needed.
Signed-off-by: David Arinzon <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Validate that `first` flag is set only for the first
descriptor in multi-buffer packets.
In case of an invalid descriptor, a reset will occur.
A new reset reason for RX data corruption has been added.
Signed-off-by: Shahar Itzko <[email protected]>
Signed-off-by: David Arinzon <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
This patch makes two changes in order to fill holes and
reduce ther overall size of the structures ena_com_dev
and ena_com_rx_ctx.
Signed-off-by: Shahar Itzko <[email protected]>
Signed-off-by: David Arinzon <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
This patch adds a counter to the ena_adapter struct in
order to keep track of reset failures.
The counter is incremented every time either ena_restore_device()
or ena_destroy_device() fail.
Signed-off-by: Osama Abboud <[email protected]>
Signed-off-by: David Arinzon <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Now that this test runs in netdev CI it looks like 10s isn't enough
for debug kernels:
selftests: net/netfilter: nft_flowtable.sh
2024/05/10 20:33:08 socat[12204] E write(7, 0x563feb16a000, 8192): Broken pipe
FAIL: file mismatch for ns1 -> ns2
-rw------- 1 root root 37345280 May 10 20:32 /tmp/tmp.Am0yEHhNqI
...
Looks like socat gets zapped too quickly, so increase timeout to 1m.
Could also reduce tx file size for KSFT_MACHINE_SLOW, but its preferrable
to have same test for both debug and nondebug.
Signed-off-by: Florian Westphal <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull hardening updates from Kees Cook:
"The bulk of the changes here are related to refactoring and expanding
the KUnit tests for string helper and fortify behavior.
Some trivial strncpy replacements in fs/ were carried in my tree. Also
some fixes to SCSI string handling were carried in my tree since the
helper for those was introduce here. Beyond that, just little fixes
all around: objtool getting confused about LKDTM+KCFI, preparing for
future refactors (constification of sysctl tables, additional
__counted_by annotations), a Clang UBSAN+i386 crash fix, and adding
more options in the hardening.config Kconfig fragment.
Summary:
- selftests: Add str*cmp tests (Ivan Orlov)
- __counted_by: provide UAPI for _le/_be variants (Erick Archer)
- Various strncpy deprecation refactors (Justin Stitt)
- stackleak: Use a copy of soon-to-be-const sysctl table (Thomas
Weißschuh)
- UBSAN: Work around i386 -regparm=3 bug with Clang prior to
version 19
- Provide helper to deal with non-NUL-terminated string copying
- SCSI: Fix older string copying bugs (with new helper)
- selftests: Consolidate string helper behavioral tests
- selftests: add memcpy() fortify tests
- string: Add additional __realloc_size() annotations for "dup"
helpers
- LKDTM: Fix KCFI+rodata+objtool confusion
- hardening.config: Enable KCFI"
* tag 'hardening-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (29 commits)
uapi: stddef.h: Provide UAPI macros for __counted_by_{le, be}
stackleak: Use a copy of the ctl_table argument
string: Add additional __realloc_size() annotations for "dup" helpers
kunit/fortify: Fix replaced failure path to unbreak __alloc_size
hardening: Enable KCFI and some other options
lkdtm: Disable CFI checking for perms functions
kunit/fortify: Add memcpy() tests
kunit/fortify: Do not spam logs with fortify WARNs
kunit/fortify: Rename tests to use recommended conventions
init: replace deprecated strncpy with strscpy_pad
kunit/fortify: Fix mismatched kvalloc()/vfree() usage
scsi: qla2xxx: Avoid possible run-time warning with long model_num
scsi: mpi3mr: Avoid possible run-time warning with long manufacturer strings
scsi: mptfusion: Avoid possible run-time warning with long manufacturer strings
fs: ecryptfs: replace deprecated strncpy with strscpy
hfsplus: refactor copy_name to not use strncpy
reiserfs: replace deprecated strncpy with scnprintf
virt: acrn: replace deprecated strncpy with strscpy
ubsan: Avoid i386 UBSAN handler crashes with Clang
ubsan: Remove 1-element array usage in debug reporting
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull execve updates from Kees Cook:
- Provide knob to change (previously fixed) coredump NOTES size
(Allen Pais)
- Add sched_prepare_exec tracepoint (Marco Elver)
- Make /proc/$pid/auxv work under binfmt_elf_fdpic (Max Filippov)
- Convert ARCH_HAVE_EXTRA_ELF_NOTES to proper Kconfig (Vignesh
Balasubramanian)
- Leave a gap between .bss and brk
* tag 'execve-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
fs/coredump: Enable dynamic configuration of max file note size
binfmt_elf_fdpic: fix /proc/<pid>/auxv
binfmt_elf: Leave a gap between .bss and brk
Replace macro "ARCH_HAVE_EXTRA_ELF_NOTES" with kconfig
tracing: Add sched_prepare_exec tracepoint
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull seccomp update from Kees Cook:
- Prepare for sysctl table constification
* tag 'seccomp-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
seccomp: Constify sysctl subhelpers
|
|
Joachim kindly merged the IPv6 support in
https://github.com/troglobit/mtools/pull/2, so we can just use his
version now. A few more fixes subsequently came in for IPv6, so even
better.
Check that the deployed mtools version is 3.0 or above. Note that the
version check breaks compatibility with my fork where I didn't bump the
version, but I assume that won't be a problem.
Signed-off-by: Vladimir Oltean <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
There is a spelling mistake in a TH_LOG message. Fix it.
Signed-off-by: Colin Ian King <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
I missed that (struct ifaddrmsg)->ifa_flags was only 8bits,
while (struct in_ifaddr)->ifa_flags is 32bits.
Use a temporary 32bit variable as I did in set_ifa_lifetime()
and check_lifetime().
Fixes: 3ddc2231c810 ("inet: annotate data-races around ifa->ifa_flags")
Reported-by: Yu Watanabe <[email protected]>
Dianosed-by: Yu Watanabe <[email protected]>
Closes: https://github.com/systemd/systemd/pull/32666#issuecomment-2103977928
Signed-off-by: Eric Dumazet <[email protected]>
Reviewed-by: Larysa Zaremba <[email protected]>
Reviewed-by: David Ahern <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Setting LED_OFF via brightness_set should deactivate hw control, so make
sure netdev trigger rules also get cleared in that case.
This fixes unwanted restoration of the default netdev trigger rules and
matches the behaviour when using the 'netdev' trigger without any
hardware offloading.
Fixes: 71e79430117d ("net: phy: air_en8811h: Add the Airoha EN8811H PHY driver")
Signed-off-by: Daniel Golle <[email protected]>
Link: https://lore.kernel.org/r/5ed8ea615890a91fa4df59a7ae8311bbdf63cdcf.1715248281.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Since the signature self-test uses RSA and SHA-256, it must only be
enabled when those algorithms are enabled. Otherwise it fails and
panics the kernel on boot-up.
Reported-by: kernel test robot <[email protected]>
Closes: https://lore.kernel.org/oe-lkp/[email protected]
Fixes: 3cde3174eb91 ("certs: Add FIPS selftests")
Cc: [email protected]
Cc: Simo Sorce <[email protected]>
Cc: David Howells <[email protected]>
Signed-off-by: Eric Biggers <[email protected]>
Reviewed-by: Jarkko Sakkinen <[email protected]>
Signed-off-by: Jarkko Sakkinen <[email protected]>
|
|
Make ASYMMETRIC_PUBLIC_KEY_SUBTYPE select CRYPTO_SIG to avoid build
errors like the following, which were possible with
CONFIG_ASYMMETRIC_PUBLIC_KEY_SUBTYPE=y && CONFIG_CRYPTO_SIG=n:
ld: vmlinux.o: in function `public_key_verify_signature':
(.text+0x306280): undefined reference to `crypto_alloc_sig'
ld: (.text+0x306300): undefined reference to `crypto_sig_set_pubkey'
ld: (.text+0x306324): undefined reference to `crypto_sig_verify'
ld: (.text+0x30636c): undefined reference to `crypto_sig_set_privkey'
Fixes: 63ba4d67594a ("KEYS: asymmetric: Use new crypto interface without scatterlists")
Cc: [email protected]
Signed-off-by: Eric Biggers <[email protected]>
Reviewed-by: Jarkko Sakkinen <[email protected]>
Signed-off-by: Jarkko Sakkinen <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next:
Patch #1 skips transaction if object type provides no .update interface.
Patch #2 skips NETDEV_CHANGENAME which is unused.
Patch #3 enables conntrack to handle Multicast Router Advertisements and
Multicast Router Solicitations from the Multicast Router Discovery
protocol (RFC4286) as untracked opposed to invalid packets.
From Linus Luessing.
Patch #4 updates DCCP conntracker to mark invalid as invalid, instead of
dropping them, from Jason Xing.
Patch #5 uses NF_DROP instead of -NF_DROP since NF_DROP is 0,
also from Jason.
Patch #6 removes reference in netfilter's sysctl documentation on pickup
entries which were already removed by Florian Westphal.
Patch #7 removes check for IPS_OFFLOAD flag to disable early drop which
allows to evict entries from the conntrack table,
also from Florian.
Patches #8 to #16 updates nf_tables pipapo set backend to allocate
the datastructure copy on-demand from preparation phase,
to better deal with OOM situations where .commit step is too late
to fail. Series from Florian Westphal.
Patch #17 adds a selftest with packetdrill to cover conntrack TCP state
transitions, also from Florian.
Patch #18 use GFP_KERNEL to clone elements from control plane to avoid
quick atomic reserves exhaustion with large sets, reporter refers
to million entries magnitude.
* tag 'nf-next-24-05-12' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next:
netfilter: nf_tables: allow clone callbacks to sleep
selftests: netfilter: add packetdrill based conntrack tests
netfilter: nft_set_pipapo: remove dirty flag
netfilter: nft_set_pipapo: move cloning of match info to insert/removal path
netfilter: nft_set_pipapo: prepare pipapo_get helper for on-demand clone
netfilter: nft_set_pipapo: merge deactivate helper into caller
netfilter: nft_set_pipapo: prepare walk function for on-demand clone
netfilter: nft_set_pipapo: prepare destroy function for on-demand clone
netfilter: nft_set_pipapo: make pipapo_clone helper return NULL
netfilter: nft_set_pipapo: move prove_locking helper around
netfilter: conntrack: remove flowtable early-drop test
netfilter: conntrack: documentation: remove reference to non-existent sysctl
netfilter: use NF_DROP instead of -NF_DROP
netfilter: conntrack: dccp: try not to drop skb in conntrack
netfilter: conntrack: fix ct-state for ICMPv6 Multicast Router Discovery
netfilter: nf_tables: remove NETDEV_CHANGENAME from netdev chain event handler
netfilter: nf_tables: skip transaction if update object is not implemented
====================
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf
Daniel Borkmann says:
====================
pull-request: bpf 2024-05-13
We've added 3 non-merge commits during the last 2 day(s) which contain
a total of 2 files changed, 62 insertions(+), 8 deletions(-).
The main changes are:
1) Fix a case where syzkaller found that it's unexpectedly possible
to attach a cgroup_skb program to the sockopt hooks. The fix adds
missing attach_type enforcement for the link_create case along
with selftests, from Stanislav Fomichev.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
selftests/bpf: Add sockopt case to verify prog_type
selftests/bpf: Extend sockopt tests to use BPF_LINK_CREATE
bpf: Add BPF_PROG_TYPE_CGROUP_SKB attach type enforcement in BPF_LINK_CREATE
====================
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Pull block updates from Jens Axboe:
- Add a partscan attribute in sysfs, fixing an issue with systemd
relying on an internal interface that went away.
- Attempt #2 at making long running discards interruptible. The
previous attempt went into 6.9, but we ended up mostly reverting it
as it had issues.
- Remove old ida_simple API in bcache
- Support for zoned write plugging, greatly improving the performance
on zoned devices.
- Remove the old throttle low interface, which has been experimental
since 2017 and never made it beyond that and isn't being used.
- Remove page->index debugging checks in brd, as it hasn't caught
anything and prepares us for removing in struct page.
- MD pull request from Song
- Don't schedule block workers on isolated CPUs
* tag 'for-6.10/block-20240511' of git://git.kernel.dk/linux: (84 commits)
blk-throttle: delay initialization until configuration
blk-throttle: remove CONFIG_BLK_DEV_THROTTLING_LOW
block: fix that util can be greater than 100%
block: support to account io_ticks precisely
block: add plug while submitting IO
bcache: fix variable length array abuse in btree_iter
bcache: Remove usage of the deprecated ida_simple_xx() API
md: Revert "md: Fix overflow in is_mddev_idle"
blk-lib: check for kill signal in ioctl BLKDISCARD
block: add a bio_await_chain helper
block: add a blk_alloc_discard_bio helper
block: add a bio_chain_and_submit helper
block: move discard checks into the ioctl handler
block: remove the discard_granularity check in __blkdev_issue_discard
block/ioctl: prefer different overflow check
null_blk: Fix the WARNING: modpost: missing MODULE_DESCRIPTION()
block: fix and simplify blkdevparts= cmdline parsing
block: refine the EOF check in blkdev_iomap_begin
block: add a partscan sysfs attribute for disks
block: add a disk_has_partscan helper
...
|
|
Pull io_uring updates from Jens Axboe:
- Greatly improve send zerocopy performance, by enabling coalescing of
sent buffers.
MSG_ZEROCOPY already does this with send(2) and sendmsg(2), but the
io_uring side did not. In local testing, the crossover point for send
zerocopy being faster is now around 3000 byte packets, and it
performs better than the sync syscall variants as well.
This feature relies on a shared branch with net-next, which was
pulled into both branches.
- Unification of how async preparation is done across opcodes.
Previously, opcodes that required extra memory for async retry would
allocate that as needed, using on-stack state until that was the
case. If async retry was needed, the on-stack state was adjusted
appropriately for a retry and then copied to the allocated memory.
This led to some fragile and ugly code, particularly for read/write
handling, and made storage retries more difficult than they needed to
be. Allocate the memory upfront, as it's cheap from our pools, and
use that state consistently both initially and also from the retry
side.
- Move away from using remap_pfn_range() for mapping the rings.
This is really not the right interface to use and can cause lifetime
issues or leaks. Additionally, it means the ring sq/cq arrays need to
be physically contigious, which can cause problems in production with
larger rings when services are restarted, as memory can be very
fragmented at that point.
Move to using vm_insert_page(s) for the ring sq/cq arrays, and apply
the same treatment to mapped ring provided buffers. This also helps
unify the code we have dealing with allocating and mapping memory.
Hard to see in the diffstat as we're adding a few features as well,
but this kills about ~400 lines of code from the codebase as well.
- Add support for bundles for send/recv.
When used with provided buffers, bundles support sending or receiving
more than one buffer at the time, improving the efficiency by only
needing to call into the networking stack once for multiple sends or
receives.
- Tweaks for our accept operations, supporting both a DONTWAIT flag for
skipping poll arm and retry if we can, and a POLLFIRST flag that the
application can use to skip the initial accept attempt and rely
purely on poll for triggering the operation. Both of these have
identical flags on the receive side already.
- Make the task_work ctx locking unconditional.
We had various code paths here that would do a mix of lock/trylock
and set the task_work state to whether or not it was locked. All of
that goes away, we lock it unconditionally and get rid of the state
flag indicating whether it's locked or not.
The state struct still exists as an empty type, can go away in the
future.
- Add support for specifying NOP completion values, allowing it to be
used for error handling testing.
- Use set/test bit for io-wq worker flags. Not strictly needed, but
also doesn't hurt and helps silence a KCSAN warning.
- Cleanups for io-wq locking and work assignments, closing a tiny race
where cancelations would not be able to find the work item reliably.
- Misc fixes, cleanups, and improvements
* tag 'for-6.10/io_uring-20240511' of git://git.kernel.dk/linux: (97 commits)
io_uring: support to inject result for NOP
io_uring: fail NOP if non-zero op flags is passed in
io_uring/net: add IORING_ACCEPT_POLL_FIRST flag
io_uring/net: add IORING_ACCEPT_DONTWAIT flag
io_uring/filetable: don't unnecessarily clear/reset bitmap
io_uring/io-wq: Use set_bit() and test_bit() at worker->flags
io_uring/msg_ring: cleanup posting to IOPOLL vs !IOPOLL ring
io_uring: Require zeroed sqe->len on provided-buffers send
io_uring/notif: disable LAZY_WAKE for linked notifs
io_uring/net: fix sendzc lazy wake polling
io_uring/msg_ring: reuse ctx->submitter_task read using READ_ONCE instead of re-reading it
io_uring/rw: reinstate thread check for retries
io_uring/notif: implement notification stacking
io_uring/notif: simplify io_notif_flush()
net: add callback for setting a ubuf_info to skb
net: extend ubuf_info callback to ops structure
io_uring/net: support bundles for recv
io_uring/net: support bundles for send
io_uring/kbuf: add helpers for getting/peeking multiple buffers
io_uring/net: add provided buffer support for IORING_OP_SEND
...
|
|
Pull vfs rw iterator updates from Christian Brauner:
"The core fs signalfd, userfaultfd, and timerfd subsystems did still
use f_op->read() instead of f_op->read_iter(). Convert them over since
we should aim to get rid of f_op->read() at some point.
Aside from that io_uring and others want to mark files as FMODE_NOWAIT
so it can make use of per-IO nonblocking hints to enable more
efficient IO. Converting those users to f_op->read_iter() allows them
to be marked with FMODE_NOWAIT"
* tag 'vfs-6.10.rw' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs:
signalfd: convert to ->read_iter()
userfaultfd: convert to ->read_iter()
timerfd: convert to ->read_iter()
new helper: copy_to_iter_full()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs
Pull netfs updates from Christian Brauner:
"This reworks the netfslib writeback implementation so that pages read
from the cache are written to the cache through ->writepages(),
thereby allowing the fscache page flag to be retired.
The reworking also:
- builds on top of the new writeback_iter() infrastructure
- makes it possible to use vectored write RPCs as discontiguous
streams of pages can be accommodated
- makes it easier to do simultaneous content crypto and stream
division
- provides support for retrying writes and re-dividing a stream
- replaces the ->launder_folio() op, so that ->writepages() is used
instead
- uses mempools to allocate the netfs_io_request and
netfs_io_subrequest structs to avoid allocation failure in the
writeback path
Some code that uses the fscache page flag is retained for
compatibility purposes with nfs and ceph. The code is switched to
using the synonymous private_2 label instead and marked with
deprecation comments.
The merge commit contains additional details on the new algorithm that
I've left out of here as it would probably be excessively detailed.
On top of the netfslib infrastructure this contains the work to
convert cifs over to netfslib"
* tag 'vfs-6.10.netfs' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs: (38 commits)
cifs: Enable large folio support
cifs: Remove some code that's no longer used, part 3
cifs: Remove some code that's no longer used, part 2
cifs: Remove some code that's no longer used, part 1
cifs: Cut over to using netfslib
cifs: Implement netfslib hooks
cifs: Make add_credits_and_wake_if() clear deducted credits
cifs: Add mempools for cifs_io_request and cifs_io_subrequest structs
cifs: Set zero_point in the copy_file_range() and remap_file_range()
cifs: Move cifs_loose_read_iter() and cifs_file_write_iter() to file.c
cifs: Replace the writedata replay bool with a netfs sreq flag
cifs: Make wait_mtu_credits take size_t args
cifs: Use more fields from netfs_io_subrequest
cifs: Replace cifs_writedata with a wrapper around netfs_io_subrequest
cifs: Replace cifs_readdata with a wrapper around netfs_io_subrequest
cifs: Use alternative invalidation to using launder_folio
netfs, afs: Use writeback retry to deal with alternate keys
netfs: Miscellaneous tidy ups
netfs: Remove the old writeback code
netfs: Cut over to using new writeback code
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs
Pull vfs mount API conversions from Christian Brauner:
"This converts qnx6, minix, debugfs, tracefs, freevxfs, and openpromfs
to the new mount api, further reducing the number of filesystems
relying on the legacy mount api"
* tag 'vfs-6.10.mount' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs:
minix: convert minix to use the new mount api
vfs: Convert tracefs to use the new mount API
vfs: Convert debugfs to use the new mount API
openpromfs: finish conversion to the new mount API
freevxfs: Convert freevxfs to the new mount API.
qnx6: convert qnx6 to use the new mount api
|
|
Merge an ACPI pfrut utility update, an ACPI documentation update and a
PNP update for 6.10:
- Fix a typo in the ACPI documentation regarding the layout of sysfs
subdirectory representing the ACPI namespace (John Watts).
- Make the ACPI pfrut utility print the update_cap field during
capability query (Chen Yu).
- Add HAS_IOPORT dependencies to PNP (Niklas Schnelle).
* acpi-tools:
ACPI: tools: pfrut: Print the update_cap field during capability query
* acpi-docs:
Documentation: firmware-guide: ACPI: Fix namespace typo
* pnp:
PNP: add HAS_IOPORT dependencies
|
|
Merge x86-specific ACPI updates, an ACPI DPTF driver update adding new
platform support to it, and an ACPI APEI update:
- Add a num-cs device property to specify the number of chip selects
for Intel Braswell to the ACPI LPSS (Intel SoC) driver and remove a
nested CONFIG_PM #ifdef from it (Andy Shevchenko).
- Move three x86-specific ACPI files to the x86 directory (Andy
Shevchenko).
- Mark SMO8810 accel on Dell XPS 15 9550 as always present and add a
PNP_UART1_SKIP quirk for Lenovo Blade2 tablets (Hans de Goede).
- Move acpi_blacklisted() declaration to asm/acpi.h (Kuppuswamy
Sathyanarayanan).
- Add Lunar Lake support to the ACPI DPTF driver (Sumeet Pawnikar).
- Mark the einj_driver driver's remove callback as __exit because it
cannot get unbound via sysfs (Uwe Kleine-König).
* acpi-x86:
ACPI: Move acpi_blacklisted() declaration to asm/acpi.h
ACPI: x86: Add PNP_UART1_SKIP quirk for Lenovo Blade2 tablets
ACPI: x86: utils: Mark SMO8810 accel on Dell XPS 15 9550 as always present
ACPI: x86: Move LPSS to x86 folder
ACPI: x86: Move blacklist to x86 folder
ACPI: x86: Move acpi_cmos_rtc to x86 folder
ACPI: x86: Introduce a Makefile
ACPI: LPSS: Remove nested ifdeffery for CONFIG_PM
ACPI: LPSS: Advertise number of chip selects via property
* acpi-dptf:
ACPI: DPTF: Add Lunar Lake support
* acpi-apei:
ACPI: APEI: EINJ: mark remove callback as __exit
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs
Pull misc vfs updates from Christian Brauner:
"This contains the usual miscellaneous features, cleanups, and fixes
for vfs and individual fses.
Features:
- Free up FMODE_* bits. I've freed up bits 6, 7, 8, and 24. That
means we now have six free FMODE_* bits in total (but bit #6
already got used for FMODE_WRITE_RESTRICTED)
- Add FOP_HUGE_PAGES flag (follow-up to FMODE_* cleanup)
- Add fd_raw cleanup class so we can make use of automatic cleanup
provided by CLASS(fd_raw, f)(fd) for O_PATH fds as well
- Optimize seq_puts()
- Simplify __seq_puts()
- Add new anon_inode_getfile_fmode() api to allow specifying f_mode
instead of open-coding it in multiple places
- Annotate struct file_handle with __counted_by() and use
struct_size()
- Warn in get_file() whether f_count resurrection from zero is
attempted (epoll/drm discussion)
- Folio-sophize aio
- Export the subvolume id in statx() for both btrfs and bcachefs
- Relax linkat(AT_EMPTY_PATH) requirements
- Add F_DUPFD_QUERY fcntl() allowing to compare two file descriptors
for dup*() equality replacing kcmp()
Cleanups:
- Compile out swapfile inode checks when swap isn't enabled
- Use (1 << n) notation for FMODE_* bitshifts for clarity
- Remove redundant variable assignment in fs/direct-io
- Cleanup uses of strncpy in orangefs
- Speed up and cleanup writeback
- Move fsparam_string_empty() helper into header since it's currently
open-coded in multiple places
- Add kernel-doc comments to proc_create_net_data_write()
- Don't needlessly read dentry->d_flags twice
Fixes:
- Fix out-of-range warning in nilfs2
- Fix ecryptfs overflow due to wrong encryption packet size
calculation
- Fix overly long line in xfs file_operations (follow-up to FMODE_*
cleanup)
- Don't raise FOP_BUFFER_{R,W}ASYNC for directories in xfs (follow-up
to FMODE_* cleanup)
- Don't call xfs_file_open from xfs_dir_open (follow-up to FMODE_*
cleanup)
- Fix stable offset api to prevent endless loops
- Fix afs file server rotations
- Prevent xattr node from overflowing the eraseblock in jffs2
- Move fdinfo PTRACE_MODE_READ procfs check into the .permission()
operation instead of .open() operation since this caused userspace
regressions"
* tag 'vfs-6.10.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs: (39 commits)
afs: Fix fileserver rotation getting stuck
selftests: add F_DUPDFD_QUERY selftests
fcntl: add F_DUPFD_QUERY fcntl()
file: add fd_raw cleanup class
fs: WARN when f_count resurrection is attempted
seq_file: Simplify __seq_puts()
seq_file: Optimize seq_puts()
proc: Move fdinfo PTRACE_MODE_READ check into the inode .permission operation
fs: Create anon_inode_getfile_fmode()
xfs: don't call xfs_file_open from xfs_dir_open
xfs: drop fop_flags for directories
xfs: fix overly long line in the file_operations
shmem: Fix shmem_rename2()
libfs: Add simple_offset_rename() API
libfs: Fix simple_offset_rename_exchange()
jffs2: prevent xattr node from overflowing the eraseblock
vfs, swap: compile out IS_SWAPFILE() on swapless configs
vfs: relax linkat() AT_EMPTY_PATH - aka flink() - requirements
fs/direct-io: remove redundant assignment to variable retval
fs/dcache: Re-use value stored to dentry->d_flags instead of re-reading
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs
Pull vfs iomap updates from Christian Brauner:
"This contains a few cleanups to the iomap code. Nothing particularly
stands out"
* tag 'vfs-6.10.iomap' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs:
iomap: do some small logical cleanup in buffered write
iomap: make iomap_write_end() return a boolean
iomap: use a new variable to handle the written bytes in iomap_write_iter()
iomap: don't increase i_size if it's not a write operation
iomap: drop the write failure handles when unsharing and zeroing
iomap: convert iomap_writepages to writeack_iter
|
|
Merge Enery Model update and a power management documentation update for
6.10:
- Make the Samsung exynos-asv driver update the Energy Model after
adjusting voltage on top of some preliminary changes of the OPP and
Enery Model generic code (Lukasz Luba).
- Remove a reference to a function that has been dropped from the power
management documentation (Bjorn Helgaas).
* pm-em:
soc: samsung: exynos-asv: Update Energy Model after adjusting voltage
PM: EM: Add em_dev_update_chip_binning()
PM: EM: Refactor em_adjust_new_capacity()
OPP: OF: Export dev_opp_pm_calc_power() for usage from EM
* pm-docs:
Documentation: PM: Update platform_pci_wakeup_init() reference
|
|
Merge cpuidle updates, changes related to system sleep and power capping
updates for 6.10:
- Fix kerneldoc description of ladder_do_selection() (Jeff Johnson).
- Convert the cpuidle kirkwood driver to platform remove callback
returning void (Yangtao Li).
- Replace deprecated strncpy() with strscpy() in the hibernation core
code (Justin Stitt).
- Use %ps to simplify debug output in the core system-wide suspend and
resume code (Len Brown).
- Remove unnecessary else from device_init_wakeup() and make
device_wakeup_disable() return void (Dhruva Gole).
- Enable PMU support in the Intel TPMI RAPL driver (Zhang Rui).
- Add support for ArrowLake-H platform to the Intel RAPL driver (Zhang
Rui).
- Avoid explicit cpumask allocation on stack in DTPM (Dawei Li).
* pm-cpuidle:
cpuidle: ladder: fix ladder_do_selection() kernel-doc
cpuidle: kirkwood: Convert to platform remove callback returning void
* pm-sleep:
PM: hibernate: replace deprecated strncpy() with strscpy()
PM: sleep: Take advantage of %ps to simplify debug output
PM: wakeup: Remove unnecessary else from device_init_wakeup()
PM: wakeup: make device_wakeup_disable() return void
* pm-powercap:
powercap: intel_rapl_tpmi: Enable PMU support
powercap: intel_rapl: Introduce APIs for PMU support
powercap: intel_rapl: Sort header files
powercap: intel_rapl: Add support for ArrowLake-H platform
powercap: DTPM: Avoid explicit cpumask allocation on stack
|
|
Merge cpufreq updates for 6.10:
- Rework the handling of disabled turbo in the intel_pstate driver and
make it update the maximum CPU frequency consistently regardless of
the reason on top of a number of cleanups (Rafael Wysocki).
- Add missing checks for NULL .exit() cpufreq driver callback to the
cpufreq core (Viresh Kumar).
- Prevent pulicy->max from going above the frequency QoS maximum value
when cpufreq_frequency_table_verify() is used (Xuewen Yan).
- Prevent a negative CPU number or frequency value from being printed
if they are really large (Joshua Yeong).
- Update MAINTAINERS entry for amd-pstate to add two new submaintainers
and a designated reviewer (Huang Rui).
- Clean up the amd-pstate driver and update its documentation (Gautham
Shenoy).
- Fix the highest frequency issue in the amd-pstate driver which limits
performance (Perry Yuan).
- Enable CPPC v2 for certain processors in the family 17H, as requested
by TR40 processor users who expect improved performance and lower
system temperature (Perry Yuan).
- Change latency and delay values to be read from platform firmware
firstly for more accurate timing (Perry Yuan).
- A new quirk is introduced for supporting amd-pstate on legacy
processors which either lack CPPC capability, or only only have CPPC
v2 capability (Perry Yuan).
- Sun50i: Add support for opp_supported_hw, H616 platform and general
cleanups (Andre Przywara, Martin Botka, Brandon Cheo Fusi, Dan
Carpenter, Viresh Kumar).
- CPPC: Fix possible null pointer dereference (Aleksandr Mishin).
- Eliminate uses of of_node_put() (Javier Carrasco, and Shivani Gupta).
- brcmstb-avs: ISO C90 forbids mixed declarations (Portia Stephens).
- mediatek: Add support for MT7988A (Sam Shih).
- cpufreq-qcom-hw: Add SM4450 compatibles in DT bindings (Tengfei Fan).
- Fix struct cpudata::epp_cached kernel-doc in the intel_pstate cpufreq
driver (Jeff Johnson).
* pm-cpufreq: (46 commits)
cpufreq: amd-pstate: fix the highest frequency issue which limits performance
cpufreq: intel_pstate: fix struct cpudata::epp_cached kernel-doc
cpufreq: Fix up printing large CPU numbers and frequency values
MAINTAINERS: cpufreq: amd-pstate: Add co-maintainers and reviewer
cpufreq: amd-pstate: remove unused variable lowest_nonlinear_freq
cpufreq: amd-pstate: fix code format problems
cpufreq: amd-pstate: Add quirk for the pstate CPPC capabilities missing
cppc_acpi: print error message if CPPC is unsupported
cpufreq: amd-pstate: get transition delay and latency value from ACPI tables
cpufreq: amd-pstate: Bail out if min/max/nominal_freq is 0
cpufreq: amd-pstate: Remove amd_get_{min,max,nominal,lowest_nonlinear}_freq()
cpufreq: amd-pstate: Unify computation of {max,min,nominal,lowest_nonlinear}_freq
cpufreq: amd-pstate: Document the units for freq variables in amd_cpudata
cpufreq: amd-pstate: Document *_limit_* fields in struct amd_cpudata
dt-bindings: cpufreq: cpufreq-qcom-hw: Add SM4450 compatibles
cpufreq: sun50i: fix error returns in dt_has_supported_hw()
cpufreq: brcmstb-avs-cpufreq: ISO C90 forbids mixed declarations
cpufreq: dt-platdev: eliminate uses of of_node_put()
cpufreq: dt: eliminate uses of of_node_put()
cpufreq: ti: Implement scope-based cleanup in ti_cpufreq_match_node()
...
|
|
Pull documentation updates from Jonathan Corbet:
"Another not-too-busy cycle for documentation, including:
- Some build-system changes to detect the variable fonts installed by
some distributions that can break the PDF build.
- Various updates and additions to the Spanish, Chinese, Italian, and
Japanese translations.
- Update the stable-kernel rules to match modern practice
... and the usual array of corrections, updates, and typo fixes"
* tag 'docs-6.10' of git://git.lwn.net/linux: (42 commits)
cgroup: Add documentation for missing zswap memory.stat
kernel-doc: Added "*" in $type_constants2 to fix 'make htmldocs' warning.
docs:core-api: fixed typos and grammar in printk-index page
Documentation: tracing: Fix spelling mistakes
docs/zh_CN/rust: Update the translation of quick-start to 6.9-rc4
docs/zh_CN/rust: Update the translation of general-information to 6.9-rc4
docs/zh_CN/rust: Update the translation of coding-guidelines to 6.9-rc4
docs/zh_CN/rust: Update the translation of arch-support to 6.9-rc4
docs: stable-kernel-rules: fix typo sent->send
docs/zh_CN: remove two inconsistent spaces
docs: scripts/check-variable-fonts.sh: Improve commands for detection
docs: stable-kernel-rules: create special tag to flag 'no backporting'
docs: stable-kernel-rules: explain use of [email protected] (w/o @vger.)
docs: stable-kernel-rules: remove code-labels tags and a indention level
docs: stable-kernel-rules: call mainline by its name and change example
docs: stable-kernel-rules: reduce redundancy
docs, kprobes: Add riscv as supported architecture
Docs: typos/spelling
docs: kernel_include.py: Cope with docutils 0.21
docs: ja_JP/howto: Catch up update in v6.8
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd
Pull keys updates from Jarkko Sakkinen:
- do not overwrite the key expiration once it is set
- move key quota updates earlier into key_put(), instead of updating
them in key_gc_unused_keys()
* tag 'keys-next-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd:
keys: Fix overwrite of key expiration on instantiation
keys: update key quotas in key_put()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd
Pull TPM updates from Jarkko Sakkinen:
"These are the changes for the TPM driver with a single major new
feature: TPM bus encryption and integrity protection. The key pair on
TPM side is generated from so called null random seed per power on of
the machine [1]. This supports the TPM encryption of the hard drive by
adding layer of protection against bus interposer attacks.
Other than that, a few minor fixes and documentation for tpm_tis to
clarify basics of TPM localities for future patch review discussions
(will be extended and refined over times, just a seed)"
Link: https://lore.kernel.org/linux-integrity/[email protected]/ [1]
* tag 'tpmdd-next-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd: (28 commits)
Documentation: tpm: Add TPM security docs toctree entry
tpm: disable the TPM if NULL name changes
Documentation: add tpm-security.rst
tpm: add the null key name as a sysfs export
KEYS: trusted: Add session encryption protection to the seal/unseal path
tpm: add session encryption protection to tpm2_get_random()
tpm: add hmac checks to tpm2_pcr_extend()
tpm: Add the rest of the session HMAC API
tpm: Add HMAC session name/handle append
tpm: Add HMAC session start and end functions
tpm: Add TCG mandated Key Derivation Functions (KDFs)
tpm: Add NULL primary creation
tpm: export the context save and load commands
tpm: add buffer function to point to returned parameters
crypto: lib - implement library version of AES in CFB mode
KEYS: trusted: tpm2: Use struct tpm_buf for sized buffers
tpm: Add tpm_buf_read_{u8,u16,u32}
tpm: TPM2B formatted buffers
tpm: Store the length of the tpm_buf data separately.
tpm: Update struct tpm_buf documentation comments
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd
Pull trusted keys updates from Jarkko Sakkinen:
"This contains a new key type for the Data Co-Processor (DCP), which is
an IP core built into many NXP SoCs such as i.mx6ull"
* tag 'keys-trusted-next-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd:
docs: trusted-encrypted: add DCP as new trust source
docs: document DCP-backed trusted keys kernel params
MAINTAINERS: add entry for DCP-based trusted keys
KEYS: trusted: Introduce NXP DCP-backed trusted keys
KEYS: trusted: improve scalability of trust source config
crypto: mxs-dcp: Add support for hardware-bound keys
|
|
Make ACPI resource management quirks, a documentation update related to
the ACPI handling of device properties and ACPI NUMA handling changes
for 6.10:
- Add ACPI IRQ override quirks for Asus Vivobook Pro N6506MV, TongFang
GXxHRXx and GMxHGxx, and XMG APEX 17 M23 (Guenter Schafranek, Tamim
Khan, Christoffer Sandberg).
- Add reference to UEFI DSD Guide to the documentation related to the
ACPI handling of device properties (Sakari Ailus).
- Fix SRAT lookup of CFMWS ranges with numa_fill_memblks(), remove
lefover architecture-dependent code from the ACPI NUMA handling code
and simplify it on top of that (Robert Richter).
* acpi-resource:
ACPI: resource: Skip IRQ override on Asus Vivobook Pro N6506MV
ACPI: resource: Do IRQ override on TongFang GXxHRXx and GMxHGxx
ACPI: resource: Do IRQ override on GMxBGxx (XMG APEX 17 M23)
* acpi-property:
ACPI: property: Add reference to UEFI DSD Guide
* acpi-numa:
ACPI/NUMA: Squash acpi_numa_memory_affinity_init() into acpi_parse_memory_affinity()
ACPI/NUMA: Squash acpi_numa_slit_init() into acpi_parse_slit()
ACPI/NUMA: Remove architecture dependent remainings
x86/numa: Fix SRAT lookup of CFMWS ranges with numa_fill_memblks()
|
|
Merge ACPI device enumeration changes and ACPI data-only tables support
updates for 6.10:
- Rearrange fields in several structures to effectively eliminate
computations from container_of() in some cases (Andy Shevchenko).
- Do some assorted cleanups of the ACPI device enumeration code (Andy
Shevchenko).
- Make the ACPI device enumeration code skip devices with _STA values
clearly identified by the specification as invalid (Rafael Wysocki).
- Rework the handling of the NHLT table to simplify and clarify it and
drop some obsolete pieces (Cezary Rojewski).
* acpi-scan:
ACPI: scan: Avoid enumerating devices with clearly invalid _STA values
ACPI: scan: Introduce typedef:s for struct acpi_hotplug_context members
ACPI: scan: Use standard error checking pattern
ACPI: scan: Move misleading comment to acpi_dma_configure_id()
ACPI: scan: Use list_first_entry_or_null() in acpi_device_hid()
ACPI: bus: Don't use "proxy" headers
ACPI: bus: Make container_of() no-op where it makes sense
* acpi-tables:
ACPI: NHLT: Streamline struct naming
ACPI: NHLT: Drop redundant types
ACPI: NHLT: Introduce API for the table
ACPI: NHLT: Reintroduce types the table consists of
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vbabka/slab
Pull slab updates from Vlastimil Babka:
"This time it's mostly random cleanups and fixes, with two performance
fixes that might have significant impact, but limited to systems
experiencing particular bad corner case scenarios rather than general
performance improvements.
The memcg hook changes are going through the mm tree due to
dependencies.
- Prevent stalls when reading /proc/slabinfo (Jianfeng Wang)
This fixes the long-standing problem that can happen with workloads
that have alloc/free patterns resulting in many partially used
slabs (in e.g. dentry cache). Reading /proc/slabinfo will traverse
the long partial slab list under spinlock with disabled irqs and
thus can stall other processes or even trigger the lockup
detection. The traversal is only done to count free objects so that
<active_objs> column can be reported along with <num_objs>.
To avoid affecting fast paths with another shared counter
(attempted in the past) or complex partial list traversal schemes
that allow rescheduling, the chosen solution resorts to
approximation - when the partial list is over 10000 slabs long, we
will only traverse first 5000 slabs from head and tail each and use
the average of those to estimate the whole list. Both head and tail
are used as the slabs near head to tend to have more free objects
than the slabs towards the tail.
It is expected the approximation should not break existing
/proc/slabinfo consumers. The <num_objs> field is still accurate
and reflects the overall kmem_cache footprint. The <active_objs>
was already imprecise due to cpu and percpu-partial slabs, so can't
be relied upon to determine exact cache usage. The difference
between <active_objs> and <num_objs> is mainly useful to determine
the slab fragmentation, and that will be possible even with the
approximation in place.
- Prevent allocating many slabs when a NUMA node is full (Chen Jun)
Currently, on NUMA systems with a node under significantly bigger
pressure than other nodes, the fallback strategy may result in each
kmalloc_node() that can't be safisfied from the preferred node, to
allocate a new slab on a fallback node, and not reuse the slabs
already on that node's partial list.
This is now fixed and partial lists of fallback nodes are checked
even for kmalloc_node() allocations. It's still preferred to
allocate a new slab on the requested node before a fallback, but
only with a GFP_NOWAIT attempt, which will fail quickly when the
node is under a significant memory pressure.
- More SLAB removal related cleanups (Xiu Jianfeng, Hyunmin Lee)
- Fix slub_kunit self-test with hardened freelists (Guenter Roeck)
- Mark racy accesses for KCSAN (linke li)
- Misc cleanups (Xiongwei Song, Haifeng Xu, Sangyun Kim)"
* tag 'slab-for-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/vbabka/slab:
mm/slub: remove the check for NULL kmalloc_caches
mm/slub: create kmalloc 96 and 192 caches regardless cache size order
mm/slub: mark racy access on slab->freelist
slub: use count_partial_free_approx() in slab_out_of_memory()
slub: introduce count_partial_free_approx()
slub: Set __GFP_COMP in kmem_cache by default
mm/slub: remove duplicate initialization for early_kmem_cache_node_alloc()
mm/slub: correct comment in do_slab_free()
mm/slub, kunit: Use inverted data to corrupt kmem cache
mm/slub: simplify get_partial_node()
mm/slub: add slub_get_cpu_partial() helper
mm/slub: remove the check of !kmem_cache_has_cpu_partial()
mm/slub: Reduce memory consumption in extreme scenarios
mm/slub: mark racy accesses on slab->slabs
mm/slub: remove dummy slabinfo functions
|
|
Merge changes related to _OSC handling and updates eliminating the owner
field from struct acpi_driver:
- Make the kernel indicate support for several ACPI features that are
in fact supported to the platform firmware through _OSC and fix
the Generic Initiator Affinity _OSC bit (Armin Wolf).
- Make the ACPI core set the owner value for ACPI drivers, drop the
owner setting from a number of drivers and eliminate the owner
field from struct acpi_driver (Krzysztof Kozlowski).
* acpi-bus: (24 commits)
ACPI: drop redundant owner from acpi_driver
virt: vmgenid: drop owner assignment
ptp: vmw: drop owner assignment
platform/x86/wireless-hotkey: drop owner assignment
platform/x86/toshiba_haps: drop owner assignment
platform/x86/toshiba_bluetooth: drop owner assignment
platform/x86/toshiba_acpi: drop owner assignment
platform/x86/sony-laptop: drop owner assignment
platform/x86/lg-laptop: drop owner assignment
platform/x86/intel/smartconnect: drop owner assignment
platform/x86/intel/rst: drop owner assignment
platform/x86/eeepc: drop owner assignment
platform/x86/dell: drop owner assignment
platform: classmate-laptop: drop owner assignment
platform: asus-laptop: drop owner assignment
platform/chrome: wilco_ec: drop owner assignment
net: fjes: drop owner assignment
Input: atlas - drop owner assignment
ACPI: store owner from modules with acpi_bus_register_driver()
ACPI: bus: Indicate support for IRQ ResourceSource thru _OSC
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu
Pull kcsan update from Paul McKenney:
"Introduce __data_racy type qualifier
This adds a __data_racy type qualifier that enables kernel developers
to inform KCSAN that a given variable is a shared variable without
needing to mark each and every access.
This allows pre-KCSAN code to be correctly (if approximately)
instrumented withh very little effort, and also provides people
reading the code a clear indication that the variable is in fact
shared.
In addition, it permits incremental transition to per-access KCSAN
marking, so that (for example) a given subsystem can be transitioned
one variable at a time, while avoiding large numbers of KCSAN warnings
during this transition"
* tag 'kcsan.2024.05.10a' of git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu:
kcsan, compiler_types: Introduce __data_racy type qualifier
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu
Pull LKMM documentation updates from Paul McKenney:
"This upgrades LKMM documentation, perhaps most notably adding a number
of litmus tests illustrating cmpxchg() ordering properties.
TL;DR: Failing cmpxchg() operations provide no ordering"
* tag 'lkmm.2024.05.10a' of git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu:
Documentation/litmus-tests: Make cmpxchg() tests safe for klitmus
Documentation/atomic_t: Emphasize that failed atomic operations give no ordering
Documentation/litmus-tests: Demonstrate unordered failing cmpxchg
Documentation/litmus-tests: Add locking tests to README
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu
Pull cmpxchg updates from Paul McKenney:
"Provide one-byte and two-byte cmpxchg() support on sparc32, parisc,
and csky
This provides native one-byte and two-byte cmpxchg() support for
sparc32 and parisc, courtesy of Al Viro. This support is provided by
the same hashed-array-of-locks technique used for the other atomic
operations provided for these two platforms.
There is also emulated one-byte cmpxchg() support for csky using a new
cmpxchg_emu_u8() function that uses a four-byte cmpxchg() to emulate
the one-byte variant.
Similar patches for emulation of one-byte cmpxchg() for arc, sh, and
xtensa have not yet received maintainer acks, so they are slated for
the v6.11 merge window"
* tag 'cmpxchg.2024.05.11a' of git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu:
csky: Emulate one-byte cmpxchg
lib: Add one-byte emulation function
parisc: add u16 support to cmpxchg()
parisc: add missing export of __cmpxchg_u8()
parisc: unify implementations of __cmpxchg_u{8,32,64}
parisc: __cmpxchg_u32(): lift conversion into the callers
sparc32: add __cmpxchg_u{8,16}() and teach __cmpxchg() to handle those sizes
sparc32: unify __cmpxchg_u{32,64}
sparc32: make the first argument of __cmpxchg_u64() volatile u64 *
sparc32: make __cmpxchg_u32() return u32
|
|
Pull RCU updates from Uladzislau Rezki:
- Fix a lockdep complain for lazy-preemptible kernel, remove redundant
BH disable for TINY_RCU, remove redundant READ_ONCE() in tree.c, fix
false positives KCSAN splat and fix buffer overflow in the
print_cpu_stall_info().
- Misc updates related to bpf, tracing and update the MAINTAINERS file.
- An improvement of a normal synchronize_rcu() call in terms of
latency. It maintains a separate track for sync. users only. This
approach bypasses per-cpu nocb-lists thus sync-users do not depend on
nocb-list length and how fast regular callbacks are processed.
- RCU tasks: switch tasks RCU grace periods to sleep at TASK_IDLE
priority, fix some comments, add some diagnostic warning to the
exit_tasks_rcu_start() and fix a buffer overflow in the
show_rcu_tasks_trace_gp_kthread().
- RCU torture: Increase memory to guest OS, fix a Tasks Rude RCU
testing, some updates for TREE09, dump mode information to debug GP
kthread state, remove redundant READ_ONCE(), fix some comments about
RCU_TORTURE_PIPE_LEN and pipe_count, remove some redundant pointer
initialization, fix a hung splat task by when the rcutorture tests
start to exit, fix invalid context warning, add '--do-kvfree'
parameter to torture test and use slow register unregister callbacks
only for rcutype test.
* tag 'rcu.next.v6.10' of https://github.com/urezki/linux: (48 commits)
rcutorture: Use rcu_gp_slow_register/unregister() only for rcutype test
torture: Scale --do-kvfree test time
rcutorture: Fix invalid context warning when enable srcu barrier testing
rcutorture: Make stall-tasks directly exit when rcutorture tests end
rcutorture: Removing redundant function pointer initialization
rcutorture: Make rcutorture support print rcu-tasks gp state
rcutorture: Use the gp_kthread_dbg operation specified by cur_ops
rcutorture: Re-use value stored to ->rtort_pipe_count instead of re-reading
rcutorture: Fix rcu_torture_one_read() pipe_count overflow comment
rcutorture: Remove extraneous rcu_torture_pipe_update_one() READ_ONCE()
rcu: Allocate WQ with WQ_MEM_RECLAIM bit set
rcu: Support direct wake-up of synchronize_rcu() users
rcu: Add a trace event for synchronize_rcu_normal()
rcu: Reduce synchronize_rcu() latency
rcu: Fix buffer overflow in print_cpu_stall_info()
rcu: Mollify sparse with RCU guard
rcu-tasks: Fix show_rcu_tasks_trace_gp_kthread buffer overflow
rcu-tasks: Fix the comments for tasks_rcu_exit_srcu_stall_timer
rcu-tasks: Replace exit_tasks_rcu_start() initialization with WARN_ON_ONCE()
rcu: Remove redundant CONFIG_PROVE_RCU #if condition
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull alpha updates from Arnd Bergmann:
"I had investigated dropping support for alpha EV5 and earlier a while
ago after noticing that this is the only supported CPU family in the
kernel without native byte access and that Debian has already dropped
support for this generation last year [1] in order to improve
performance for the newer machines.
This topic came up again when Paul McKenney noticed that parts of the
RCU code already rely on byte access and do not work on alpha EV5
reliably, so we decided on using my series to avoid the problem
entirely.
Al Viro did another series for alpha to address all the known build
issues. I rebased his patches without any further changes and included
it as a baseline for my work here to avoid conflicts and allow
backporting the fixes to stable kernels for the now removed hardware
support as well"
[ I dearly loved alpha back in the days, but the lack of byte and word
operations was a horrible mistake and made everything worse -
including very much the crazy IO contortions that resulted from it.
It certainly wasn't the only mistake in the architecture, but it's the
first-order issue.
So while it's a bit sad to see the support for my first alpha go away,
if you want to run museum hardware, maybe you should use museum
kernels.. - Linus ]
* tag 'asm-generic-alpha' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
alpha: drop pre-EV56 support
alpha: cabriolet: remove EV5 CPU support
alpha: remove LCA and APECS based machines
alpha: sable: remove early machine support
alpha: remove DECpc AXP150 (Jensen) support
alpha: trim the unused stuff from asm-offsets.c
alpha: jensen, t2 - make __EXTERN_INLINE same as for the rest
alpha: core_lca: take the unused functions out
alpha: missing includes
alpha: sys_sio: fix misspelled ifdefs
alpha: don't make functions public without a reason
alpha: add clone3() support
alpha: fix modversions for strcpy() et.al.
alpha: sort scr_mem{cpy,move}w() out
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC defconfig updates from Arnd Bergmann:
"Most of the changes enable additional device driver modules and arm64
platforms. In addition, the usb onboard-device support and ext4
security labels are turned on"
* tag 'soc-defconfig-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (23 commits)
arm64: defconfig: enable Airoha platform
arm64: defconfig: enable Khadas TS050 panel as module
arm64: defconfig: select INTERCONNECT_QCOM_SM6115 as built-in
arm64: defconfig: Enable Tegra Security Engine
arm64: defconfig: enable REGULATOR_QCOM_USB_VBUS
ARM: imx_v6_v7_defconfig: Update ONBOARD_USB_HUB to ONBOAD_USB_DEV
arm64: defconfig: enable ext4 security labels
arm64: defconfig: qcom: enable X1E80100 sound card
ARM: configs: sunxi: Enable DRM_DW_HDMI
arm64: defconfig: build snd_bcm2835 as module
arm64: defconfig: enable Rockchip Samsung USBDP PHY
ARM: shmobile: defconfig: Refresh for v6.9-rc1
arm64: defconfig: build ath12k as a module
arm64: defconfig: Enable sc7280 display and gpu clock controllers
ARM: imx_v6_v7_defconfig: Select CONFIG_USB_ONBOARD_HUB
arm64: defconfig: Enable DRM_IMX8MP_DW_HDMI_BRIDGE as module
arm64: defconfig: support Mali CSF-based GPUs
arm64: defconfig: enable Rockchip RK3308 internal audio codec driver
arm64: defconfig: Enable R9A09G057 SoC
arm64: defconfig: Enable Renesas DA9062 PMIC
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC code changes from Arnd Bergmann:
"The code changes are fairly minimal, there is a bit of conversion of
the old orion5x platform to modern gpio descriptors, the Kconfig entry
for the added EN7581 platform and a sysfs change for the i.MX PMU
device"
* tag 'soc-arm-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
arm64: add Airoha EN7581 platform
ARM: orion5x: Convert TS409 board to GPIO descriptors for LEDs
ARM: orion5x: Convert Net2big board to GPIO descriptors for LEDs
ARM: orion5x: Convert MV2120 board to GPIO descriptors for LEDs
ARM: orion5x: Convert DNS323 board to GPIO descriptors for LEDs
ARM: orion5x: Convert D2Net board to GPIO descriptors for LEDs
ARM: imx: Assign parents for mmdc event_source devices
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC driver updates from Arnd Bergmann:
"As usual, these are updates for drivers that are specific to certain
SoCs or firmware running on them.
Notable updates include
- The new STMicroelectronics STM32 "firewall" bus driver that is used
to provide a barrier between different parts of an SoC
- Lots of updates for the Qualcomm platform drivers, in particular
SCM, which gets a rewrite of its initialization code
- Firmware driver updates for Arm FF-A notification interrupts and
indirect messaging, SCMI firmware support for pin control and
vendor specific interfaces, and TEE firmware interface changes
across multiple TEE drivers
- A larger cleanup of the Mediatek CMDQ driver and some related bits
- Kconfig changes for riscv drivers to prepare for adding Kanaan k230
support
- Multiple minor updates for the TI sysc bus driver, memory
controllers, hisilicon hccs and more"
* tag 'soc-drivers-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (103 commits)
firmware: qcom: uefisecapp: Allow on sc8180x Primus and Flex 5G
soc: qcom: pmic_glink: Make client-lock non-sleeping
dt-bindings: soc: qcom,wcnss: fix bluetooth address example
soc/tegra: pmc: Add EQOS wake event for Tegra194 and Tegra234
bus: stm32_firewall: fix off by one in stm32_firewall_get_firewall()
bus: etzpc: introduce ETZPC firewall controller driver
firmware: arm_ffa: Avoid queuing work when running on the worker queue
bus: ti-sysc: Drop legacy idle quirk handling
bus: ti-sysc: Drop legacy quirk handling for smartreflex
bus: ti-sysc: Drop legacy quirk handling for uarts
bus: ti-sysc: Add a description and copyrights
bus: ti-sysc: Move check for no-reset-on-init
soc: hisilicon: kunpeng_hccs: replace MAILBOX dependency with PCC
soc: hisilicon: kunpeng_hccs: Add the check for obtaining complete port attribute
firmware: arm_ffa: Fix memory corruption in ffa_msg_send2()
bus: rifsc: introduce RIFSC firewall controller driver
of: property: fw_devlink: Add support for "access-controller"
soc: mediatek: mtk-socinfo: Correct the marketing name for MT8188GV
soc: mediatek: mtk-socinfo: Add entry for MT8395AV/ZA Genio 1200
soc: mediatek: mtk-mutex: Add support for MT8188 VPPSYS
...
|
|
Pull SoC devicetree updates from Arnd Bergmann:
"The updates this time are a bit smaller than most times, mainly
because it is not totally dominated by new Qualcomm hardware support.
Instead, we larger than average updates for Rockchips, NXP, Allwinner
and TI. The only two new SoCs this time are both from NXP and are
minor variants of already supported ones.
The updates for aspeed, amlogic and mediatek came a little late, so
I'm saving those for part 2 in a few days if everything turns out
fine.
New machines this time contain:
- two Broadcom SoC based wireless routers from Asus
- Five allwinner based consumer devices for gaming, set-top-box and
eboot reader applications
- Three older phones based on Qualcomm chips, plus the more recent
Sony Xperia 1 V
- 14 industrial and embedded boards based on NXP i.MX6, i.MX8,
layerscape and s32g3 SoCs
- six rockchips boards including another handheld game console and a
few single-board computers
On top of these, we have the usual cleanups for dtc warnings and
updates to add more features to already merged machines"
* tag 'soc-dt-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (612 commits)
arm64: dts: marvell: espressobin-ultra: fix Ethernet Switch unit address
arm64: dts: marvell: turris-mox: drop unneeded flash address/size-cells
arm64: dts: marvell: eDPU: drop redundant address/size-cells
arm64: dts: qcom: pm6150: correct USB VBUS regulator compatible
arm64: dts: rockchip: add rk3588 pcie and php IOMMUs
arm64: dts: rockchip: enable onboard spi flash for rock-3a
arm64: dts: rockchip: add USB-C support to rk3588s-orangepi-5
arm64: dts: rockchip: Enable GPU on Orange Pi 5
arm64: dts: rockchip: enable GPU on khadas-edge2
arm64: dts: rockchip: Add USB3 on Edgeble NCM6A-IO board
arm64: dts: rockchip: Support poweroff on Edgeble Neural Compute Module
arm64: dts: rockchip: Add Radxa ROCK 3C
dt-bindings: arm: rockchip: add Radxa ROCK 3C
arm64: dts: exynos: gs101: specify empty clocks for remaining pinctrl
arm64: dts: exynos: gs101: specify bus clock for pinctrl_hsi2
arm64: dts: exynos: gs101: specify bus clock for pinctrl_peric[01]
arm64: dts: exynos: gs101: specify bus clock for pinctrl (far) alive
arm64: dts: Add/fix /memory node unit-addresses
arm64: dts: qcom: qcs404: fix bluetooth device address
arm64: dts: qcom: sc8280xp-x13s: enable USB MP and fingerprint reader
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Alexander Gordeev:
- Store AP Query Configuration Information in a static buffer
- Rework the AP initialization and add missing cleanups to the error
path
- Swap IRQ and AP bus/device registration to avoid race conditions
- Export prot_virt_guest symbol
- Introduce AP configuration changes notifier interface to facilitate
modularization of the AP bus
- Add CONFIG_AP kernel configuration option to allow modularization of
the AP bus
- Rework CONFIG_ZCRYPT_DEBUG kernel configuration option description
and dependency and rename it to CONFIG_AP_DEBUG
- Convert sprintf() and snprintf() to sysfs_emit() in CIO code
- Adjust indentation of RELOCS command build step
- Make crypto performance counters upward compatible
- Convert make_page_secure() and gmap_make_secure() to use folio
- Rework channel-utilization-block (CUB) handling in preparation of
introducing additional CUBs
- Use attribute groups to simplify registration, removal and extension
of measurement-related channel-path sysfs attributes
- Add a per-channel-path binary "ext_measurement" sysfs attribute that
provides access to extended channel-path measurement data
- Export measurement data for all channel-measurement-groups (CMG), not
only for a specific ones. This enables support of new CMG data
formats in userspace without the need for kernel changes
- Add a per-channel-path sysfs attribute "speed_bps" that provides the
operating speed in bits per second or 0 if the operating speed is not
available
- The CIO tracepoint subchannel-type field "st" is incorrectly set to
the value of subchannel-enabled SCHIB "ena" field. Fix that
- Do not forcefully limit vmemmap starting address to MAX_PHYSMEM_BITS
- Consider the maximum physical address available to a DCSS segment
(512GB) when memory layout is set up
- Simplify the virtual memory layout setup by reducing the size of
identity mapping vs vmemmap overlap
- Swap vmalloc and Lowcore/Real Memory Copy areas in virtual memory.
This will allow to place the kernel image next to kernel modules
- Move everyting KASLR related from <asm/setup.h> to <asm/page.h>
- Put virtual memory layout information into a structure to improve
code generation
- Currently __kaslr_offset is the kernel offset in both physical and
virtual memory spaces. Uncouple these offsets to allow uncoupling of
the addresses spaces
- Currently the identity mapping base address is implicit and is always
set to zero. Make it explicit by putting into __identity_base
persistent boot variable and use it in proper context
- Introduce .amode31 section start and end macros AMODE31_START and
AMODE31_END
- Introduce OS_INFO entries that do not reference any data in memory,
but rather provide only values
- Store virtual memory layout in OS_INFO. It is read out by
makedumpfile, crash and other tools
- Store virtual memory layout in VMCORE_INFO. It is read out by crash
and other tools when /proc/kcore device is used
- Create additional PT_LOAD ELF program header that covers kernel image
only, so that vmcore tools could locate kernel text and data when
virtual and physical memory spaces are uncoupled
- Uncouple physical and virtual address spaces
- Map kernel at fixed location when KASLR mode is disabled. The
location is defined by CONFIG_KERNEL_IMAGE_BASE kernel configuration
value.
- Rework deployment of kernel image for both compressed and
uncompressed variants as defined by CONFIG_KERNEL_UNCOMPRESSED kernel
configuration value
- Move .vmlinux.relocs section in front of the compressed kernel. The
interim section rescue step is avoided as result
- Correct modules thunk offset calculation when branch target is more
than 2GB away
- Kernel modules contain their own set of expoline thunks. Now that the
kernel modules area is less than 4GB away from kernel expoline
thunks, make modules use kernel expolines. Also make EXPOLINE_EXTERN
the default if the compiler supports it
- userfaultfd can insert shared zeropages into processes running VMs,
but that is not allowed for s390. Fallback to allocating a fresh
zeroed anonymous folio and insert that instead
- Re-enable shared zeropages for non-PV and non-skeys KVM guests
- Rename hex2bitmap() to ap_hex2bitmap() and export it for external use
- Add ap_config sysfs attribute to provide the means for setting or
displaying adapters, domains and control domains assigned to a
vfio-ap mediated device in a single operation
- Make vfio_ap_mdev_link_queue() ignore duplicate link requests
- Add write support to ap_config sysfs attribute to allow atomic update
a vfio-ap mediated device state
- Document ap_config sysfs attribute
- Function os_info_old_init() is expected to be called only from a
regular kdump kernel. Enable it to be called from a stand-alone dump
kernel
- Address gcc -Warray-bounds warning and fix array size in struct
os_info
- s390 does not support SMBIOS, so drop unneeded CONFIG_DMI checks
- Use unwinder instead of __builtin_return_address() with ftrace to
prevent returning of undefined values
- Sections .hash and .gnu.hash are only created when CONFIG_PIE_BUILD
kernel is enabled. Drop these for the case CONFIG_PIE_BUILD is
disabled
- Compile kernel with -fPIC and link with -no-pie to allow kpatch
feature always succeed and drop the whole CONFIG_PIE_BUILD
option-enabled code
- Add missing virt_to_phys() converter for VSIE facility and crypto
control blocks
* tag 's390-6.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (54 commits)
Revert "s390: Relocate vmlinux ELF data to virtual address space"
KVM: s390: vsie: Use virt_to_phys for crypto control block
s390: Relocate vmlinux ELF data to virtual address space
s390: Compile kernel with -fPIC and link with -no-pie
s390: vmlinux.lds.S: Drop .hash and .gnu.hash for !CONFIG_PIE_BUILD
s390/ftrace: Use unwinder instead of __builtin_return_address()
s390/pci: Drop unneeded reference to CONFIG_DMI
s390/os_info: Fix array size in struct os_info
s390/os_info: Initialize old os_info in standalone dump kernel
docs: Update s390 vfio-ap doc for ap_config sysfs attribute
s390/vfio-ap: Add write support to sysfs attr ap_config
s390/vfio-ap: Ignore duplicate link requests in vfio_ap_mdev_link_queue
s390/vfio-ap: Add sysfs attr, ap_config, to export mdev state
s390/ap: Externalize AP bus specific bitmap reading function
s390/mm: Re-enable the shared zeropage for !PV and !skeys KVM guests
mm/userfaultfd: Do not place zeropages when zeropages are disallowed
s390/expoline: Make modules use kernel expolines
s390/nospec: Correct modules thunk offset calculation
s390/boot: Do not rescue .vmlinux.relocs section
s390/boot: Rework deployment of the kernel image
...
|