| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
When Sink negotiates PPS, the voltage range of selected PPS APDO might
not cover the previous voltage (out_volt). If the previous out_volt is
lower than the new min_volt, the output voltage in RDO might be set to
an invalid value. For instance, supposed that the previous voltage is
5V, and the new voltage range in the APDO is 7V-12V. Then the output
voltage in the RDO should not be set to 5V which is lower than the
possible min_volt 7V.
Fix this by choosing the maximal value between the previous voltage and
the new min_volt first. And ensure that this value will not exceed the
new max_volt. The new out_volt will fall within the new voltage range
while being the closest value compared to the previous out_volt.
Signed-off-by: Kyle Tso <[email protected]>
Reviewed-by: Adam Thomson <[email protected]>
Reviewed-by: Guenter Roeck <[email protected]>
Reviewed-by: Heikki Krogerus <[email protected]>
Fixes: c710d0bb76ff0 ("usb: typec: tcpm: Extend the matching rules on PPS APDO selection")
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v5.0-rc4
Dwc3 got a fix for cases when gadget driver queue an OUT request of
length 0; this is a case that has been overlooked for quite some time
now.
Exynos' dwc3 glue layer got a fix on the error path for those cases
where clk_prepare_enable() fails.
TI's AM335x PHY driver got a fix for a race condition during
probe. This race happened because driver was powering off the PHY only
after adding the PHY handle to the framework. The result is that we
could fall into a situation where user of the PHY (MUSB) could call
phy_init() before phy driver's probe() called phy_poweroff() which
would result in a powered off PHY after phy_init() was called.
The old net2272 driver got a fix for an erroneous use of bitwise
negation.
* tag 'fixes-for-v5.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb:
usb: phy: am335x: fix race condition in _probe
usb: dwc3: exynos: Fix error handling of clk_prepare_enable
usb: phy: fix link errors
usb: gadget: udc: net2272: Fix bitwise and boolean operations
usb: dwc3: gadget: Handle 0 xfer length for OUT EP
|
|
Jose Abreu says:
====================
net: stmmac: Misc fixes
Some misc fixes for stmmac targeting -net.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
In stmmac xmit callback we use a different flow for TSO packets but TSO
xmit callback is not disabling the EEE mode.
Fix this by disabling earlier the EEE mode, i.e. before calling the TSO
xmit callback.
Signed-off-by: Jose Abreu <[email protected]>
Cc: Joao Pinto <[email protected]>
Cc: David S. Miller <[email protected]>
Cc: Giuseppe Cavallaro <[email protected]>
Cc: Alexandre Torgue <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The number of TSO enabled channels in HW can be different than the
number of total channels. There is no way to determined, at runtime, the
number of TSO capable channels and its safe to assume that if TSO is
enabled then at least channel 0 will be TSO capable.
Lets always send TSO packets from Queue 0.
Signed-off-by: Jose Abreu <[email protected]>
Cc: Joao Pinto <[email protected]>
Cc: David S. Miller <[email protected]>
Cc: Giuseppe Cavallaro <[email protected]>
Cc: Alexandre Torgue <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
If we don't have DT then stmmac_clk will not be available. Let's add a
new Platform Data field so that we can specify the refclk by this mean.
This way we can still use the coalesce command in PCI based setups.
Signed-off-by: Jose Abreu <[email protected]>
Cc: Joao Pinto <[email protected]>
Cc: David S. Miller <[email protected]>
Cc: Giuseppe Cavallaro <[email protected]>
Cc: Alexandre Torgue <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
While implementing ipvlan l3 and l3s mode for kubernetes CNI plugin,
I ran into the issue that while l3 mode is working fine, l3s mode
does not have any connectivity to kube-apiserver and hence all pods
end up in Error state as well. The ipvlan master device sits on
top of a bond device and hostns traffic to kube-apiserver (also running
in hostns) is DNATed from 10.152.183.1:443 to 139.178.29.207:37573
where the latter is the address of the bond0. While in l3 mode, a
curl to https://10.152.183.1:443 or to https://139.178.29.207:37573
works fine from hostns, neither of them do in case of l3s. In the
latter only a curl to https://127.0.0.1:37573 appeared to work where
for local addresses of bond0 I saw kernel suddenly starting to emit
ARP requests to query HW address of bond0 which remained unanswered
and neighbor entries in INCOMPLETE state. These ARP requests only
happen while in l3s.
Debugging this further, I found the issue is that l3s mode is piggy-
backing on l3 master device, and in this case local routes are using
l3mdev_master_dev_rcu(dev) instead of net->loopback_dev as per commit
f5a0aab84b74 ("net: ipv4: dst for local input routes should use l3mdev
if relevant") and 5f02ce24c269 ("net: l3mdev: Allow the l3mdev to be
a loopback"). I found that reverting them back into using the
net->loopback_dev fixed ipvlan l3s connectivity and got everything
working for the CNI.
Now judging from 4fbae7d83c98 ("ipvlan: Introduce l3s mode") and the
l3mdev paper in [0] the only sole reason why ipvlan l3s is relying
on l3 master device is to get the l3mdev_ip_rcv() receive hook for
setting the dst entry of the input route without adding its own
ipvlan specific hacks into the receive path, however, any l3 domain
semantics beyond just that are breaking l3s operation. Note that
ipvlan also has the ability to dynamically switch its internal
operation from l3 to l3s for all ports via ipvlan_set_port_mode()
at runtime. In any case, l3 vs l3s soley distinguishes itself by
'de-confusing' netfilter through switching skb->dev to ipvlan slave
device late in NF_INET_LOCAL_IN before handing the skb to L4.
Minimal fix taken here is to add a IFF_L3MDEV_RX_HANDLER flag which,
if set from ipvlan setup, gets us only the wanted l3mdev_l3_rcv() hook
without any additional l3mdev semantics on top. This should also have
minimal impact since dev->priv_flags is already hot in cache. With
this set, l3s mode is working fine and I also get things like
masquerading pod traffic on the ipvlan master properly working.
[0] https://netdevconf.org/1.2/papers/ahern-what-is-l3mdev-paper.pdf
Fixes: f5a0aab84b74 ("net: ipv4: dst for local input routes should use l3mdev if relevant")
Fixes: 5f02ce24c269 ("net: l3mdev: Allow the l3mdev to be a loopback")
Fixes: 4fbae7d83c98 ("ipvlan: Introduce l3s mode")
Signed-off-by: Daniel Borkmann <[email protected]>
Cc: Mahesh Bandewar <[email protected]>
Cc: David Ahern <[email protected]>
Cc: Florian Westphal <[email protected]>
Cc: Martynas Pumputis <[email protected]>
Acked-by: David Ahern <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Use pskb_may_pull() to make sure the optional fields are in skb linear
parts, so we can safely read them later.
It's easy to reproduce the issue with a net driver that supports paged
skb data. Just create a L2TPv3 over IP tunnel and then generates some
network traffic.
Once reproduced, rx err in /sys/kernel/debug/l2tp/tunnels will increase.
Changes in v4:
1. s/l2tp_v3_pull_opt/l2tp_v3_ensure_opt_in_linear/
2. s/tunnel->version != L2TP_HDR_VER_2/tunnel->version == L2TP_HDR_VER_3/
3. Add 'Fixes' in commit messages.
Changes in v3:
1. To keep consistency, move the code out of l2tp_recv_common.
2. Use "net" instead of "net-next", since this is a bug fix.
Changes in v2:
1. Only fix L2TPv3 to make code simple.
To fix both L2TPv3 and L2TPv2, we'd better refactor l2tp_recv_common.
It's complicated to do so.
2. Reloading pointers after pskb_may_pull
Fixes: f7faffa3ff8e ("l2tp: Add L2TPv3 protocol support")
Fixes: 0d76751fad77 ("l2tp: Add L2TPv3 IP encapsulation (no UDP) support")
Fixes: a32e0eec7042 ("l2tp: introduce L2TPv3 IP encapsulation support for IPv6")
Signed-off-by: Jacob Wen <[email protected]>
Acked-by: Guillaume Nault <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Call tun_set_real_num_queues() after the increment of tun->numqueues
since the former depends on it. Otherwise, the number of queues is not
correctly accounted for, which results to warnings similar to:
"vnet0 selects TX queue 11, but real number of TX queues is 11".
Fixes: 0b7959b62573 ("tun: publish tfile after it's fully initialized")
Reported-and-tested-by: George Amanakis <[email protected]>
Signed-off-by: George Amanakis <[email protected]>
Signed-off-by: Stanislav Fomichev <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
skb->cb may contain data from previous layers (in an observed case
IPv4 with L3 Master Device). In the observed scenario, the data in
IPCB(skb)->frags was misinterpreted as IP6CB(skb)->frag_max_size,
eventually caused an unexpected IPv6 fragmentation in ip6_fragment()
through ip6_finish_output().
This patch clears IP6CB(skb), which potentially contains garbage data,
on the SRH ip4ip6 encapsulation.
Fixes: 32d99d0b6702 ("ipv6: sr: add support for ip4ip6 encapsulation")
Signed-off-by: Yohei Kanemaru <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Toshiaki Makita says:
====================
virtio_net: Fix problems around XDP tx and napi_tx
While I'm looking into how to account standard tx counters on XDP tx
processing, I found several bugs around XDP tx and napi_tx.
Patch1: Fix oops on error path. Patch2 depends on this.
Patch2: Fix memory corruption on freeing xdp_frames with napi_tx enabled.
Patch3: Minor fix patch5 depends on.
Patch4: Fix memory corruption on processing xdp_frames when XDP is disabled.
Also patch5 depends on this.
Patch5: Fix memory corruption on processing xdp_frames while XDP is being
disabled.
Patch6: Minor fix patch7 depends on.
Patch7: Fix memory corruption on freeing sk_buff or xdp_frames when a normal
queue is reused for XDP and vise versa.
v2:
- patch5: Make rcu_assign_pointer/synchronize_net conditional instead of
_virtnet_set_queues.
- patch7: Use napi_consume_skb() instead of dev_consume_skb_any()
====================
Signed-off-by: Toshiaki Makita <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
We do not reset or free up unused buffers when enabling/disabling XDP,
so it can happen that xdp_frames are freed after disabling XDP or
sk_buffs are freed after enabling XDP on xdp tx queues.
Thus we need to handle both forms (xdp_frames and sk_buffs) regardless
of XDP setting.
One way to trigger this problem is to disable XDP when napi_tx is
enabled. In that case, virtnet_xdp_set() calls virtnet_napi_enable()
which kicks NAPI. The NAPI handler will call virtnet_poll_cleantx()
which invokes free_old_xmit_skbs() for queues which have been used by
XDP.
Note that even with this change we need to keep skipping
free_old_xmit_skbs() from NAPI handlers when XDP is enabled, because XDP
tx queues do not aquire queue locks.
- v2: Use napi_consume_skb() instead of dev_consume_skb_any()
Fixes: 4941d472bf95 ("virtio-net: do not reset during XDP set")
Signed-off-by: Toshiaki Makita <[email protected]>
Acked-by: Jason Wang <[email protected]>
Acked-by: Michael S. Tsirkin <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
put_page() can work as a fallback for freeing xdp_frames, but the
appropriate way is to use xdp_return_frame().
Fixes: cac320c850ef ("virtio_net: convert to use generic xdp_frame and xdp_return_frame API")
Signed-off-by: Toshiaki Makita <[email protected]>
Acked-by: Jason Wang <[email protected]>
Acked-by: Jesper Dangaard Brouer <[email protected]>
Acked-by: Michael S. Tsirkin <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Commit 8dcc5b0ab0ec ("virtio_net: fix ndo_xdp_xmit crash towards dev not
ready for XDP") tried to avoid access to unexpected sq while XDP is
disabled, but was not complete.
There was a small window which causes out of bounds sq access in
virtnet_xdp_xmit() while disabling XDP.
An example case of
- curr_queue_pairs = 6 (2 for SKB and 4 for XDP)
- online_cpu_num = xdp_queue_paris = 4
when XDP is enabled:
CPU 0 CPU 1
(Disabling XDP) (Processing redirected XDP frames)
virtnet_xdp_xmit()
virtnet_xdp_set()
_virtnet_set_queues()
set curr_queue_pairs (2)
check if rq->xdp_prog is not NULL
virtnet_xdp_sq(vi)
qp = curr_queue_pairs -
xdp_queue_pairs +
smp_processor_id()
= 2 - 4 + 1 = -1
sq = &vi->sq[qp] // out of bounds access
set xdp_queue_pairs (0)
rq->xdp_prog = NULL
Basically we should not change curr_queue_pairs and xdp_queue_pairs
while someone can read the values. Thus, when disabling XDP, assign NULL
to rq->xdp_prog first, and wait for RCU grace period, then change
xxx_queue_pairs.
Note that we need to keep the current order when enabling XDP though.
- v2: Make rcu_assign_pointer/synchronize_net conditional instead of
_virtnet_set_queues.
Fixes: 186b3c998c50 ("virtio-net: support XDP_REDIRECT")
Signed-off-by: Toshiaki Makita <[email protected]>
Acked-by: Jason Wang <[email protected]>
Acked-by: Michael S. Tsirkin <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
When XDP is disabled, curr_queue_pairs + smp_processor_id() can be
larger than max_queue_pairs.
There is no guarantee that we have enough XDP send queues dedicated for
each cpu when XDP is disabled, so do not count drops on sq in that case.
Fixes: 5b8f3c8d30a6 ("virtio_net: Add XDP related stats")
Signed-off-by: Toshiaki Makita <[email protected]>
Acked-by: Jason Wang <[email protected]>
Acked-by: Michael S. Tsirkin <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
When _virtnet_set_queues() failed we did not restore real_num_rx_queues.
Fix this by placing the change of real_num_rx_queues after
_virtnet_set_queues().
This order is also in line with virtnet_set_channels().
Fixes: 4941d472bf95 ("virtio-net: do not reset during XDP set")
Signed-off-by: Toshiaki Makita <[email protected]>
Acked-by: Jason Wang <[email protected]>
Acked-by: Michael S. Tsirkin <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
When napi_tx is enabled, virtnet_poll_cleantx() called
free_old_xmit_skbs() even for xdp send queue.
This is bogus since the queue has xdp_frames, not sk_buffs, thus mangled
device tx bytes counters because skb->len is meaningless value, and even
triggered oops due to general protection fault on freeing them.
Since xdp send queues do not aquire locks, old xdp_frames should be
freed only in virtnet_xdp_xmit(), so just skip free_old_xmit_skbs() for
xdp send queues.
Similarly virtnet_poll_tx() called free_old_xmit_skbs(). This NAPI
handler is called even without calling start_xmit() because cb for tx is
by default enabled. Once the handler is called, it enabled the cb again,
and then the handler would be called again. We don't need this handler
for XDP, so don't enable cb as well as not calling free_old_xmit_skbs().
Also, we need to disable tx NAPI when disabling XDP, so
virtnet_poll_tx() can safely access curr_queue_pairs and
xdp_queue_pairs, which are not atomically updated while disabling XDP.
Fixes: b92f1e6751a6 ("virtio-net: transmit napi")
Fixes: 7b0411ef4aa6 ("virtio-net: clean tx descriptors from rx napi")
Signed-off-by: Toshiaki Makita <[email protected]>
Acked-by: Jason Wang <[email protected]>
Acked-by: Michael S. Tsirkin <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Commit 4e09ff536284 ("virtio-net: disable NAPI only when enabled during
XDP set") tried to fix inappropriate NAPI enabling/disabling when
!netif_running(), but was not complete.
On error path virtio_net could enable NAPI even when !netif_running().
This can cause enabling NAPI twice on virtnet_open(), which would
trigger BUG_ON() in napi_enable().
Fixes: 4941d472bf95b ("virtio-net: do not reset during XDP set")
Signed-off-by: Toshiaki Makita <[email protected]>
Acked-by: Jason Wang <[email protected]>
Acked-by: Michael S. Tsirkin <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Lorenzo Bianconi says:
====================
erspan: always reports output key to userspace
Erspan protocol relies on output key to set session id header field.
However TUNNEL_KEY bit is cleared in order to not add key field to
the external GRE header and so the configured o_key is not reported
to userspace.
Fix the issue adding TUNNEL_KEY bit to the o_flags parameter dumping
device info
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
As Erspan_v4, Erspan_v6 protocol relies on o_key to configure
session id header field. However TUNNEL_KEY bit is cleared in
ip6erspan_tunnel_xmit since ERSPAN protocol does not set the key field
of the external GRE header and so the configured o_key is not reported
to userspace. The issue can be triggered with the following reproducer:
$ip link add ip6erspan1 type ip6erspan local 2000::1 remote 2000::2 \
key 1 seq erspan_ver 1
$ip link set ip6erspan1 up
ip -d link sh ip6erspan1
ip6erspan1@NONE: <BROADCAST,MULTICAST> mtu 1422 qdisc noop state DOWN mode DEFAULT
link/ether ba:ff:09:24:c3:0e brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 1500
ip6erspan remote 2000::2 local 2000::1 encaplimit 4 flowlabel 0x00000 ikey 0.0.0.1 iseq oseq
Fix the issue adding TUNNEL_KEY bit to the o_flags parameter in
ip6gre_fill_info
Fixes: 5a963eb61b7c ("ip6_gre: Add ERSPAN native tunnel support")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Erspan protocol (version 1 and 2) relies on o_key to configure
session id header field. However TUNNEL_KEY bit is cleared in
erspan_xmit since ERSPAN protocol does not set the key field
of the external GRE header and so the configured o_key is not reported
to userspace. The issue can be triggered with the following reproducer:
$ip link add erspan1 type erspan local 192.168.0.1 remote 192.168.0.2 \
key 1 seq erspan_ver 1
$ip link set erspan1 up
$ip -d link sh erspan1
erspan1@NONE: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1450 qdisc pfifo_fast state UNKNOWN mode DEFAULT
link/ether 52:aa:99:95:9a:b5 brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 1500
erspan remote 192.168.0.2 local 192.168.0.1 ttl inherit ikey 0.0.0.1 iseq oseq erspan_index 0
Fix the issue adding TUNNEL_KEY bit to the o_flags parameter in
ipgre_fill_info
Fixes: 84e54fe0a5ea ("gre: introduce native tunnel support for ERSPAN")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The default time is declared in units of microsecnds,
but is used as nanoseconds, resulting in significant
accounting errors for idle state 0 time when all idle
states deeper than 0 are disabled.
Under these unusual conditions, we don't really care
about the poll time limit anyhow.
Fixes: 800fb34a99ce ("cpuidle: poll_state: Disregard disable idle states")
Signed-off-by: Doug Smythies <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
A deadlock has been seen when swicthing clocksources which use
PM-runtime. The call path is:
change_clocksource
...
write_seqcount_begin
...
timekeeping_update
...
sh_cmt_clocksource_enable
...
rpm_resume
pm_runtime_mark_last_busy
ktime_get
do
read_seqcount_begin
while read_seqcount_retry
....
write_seqcount_end
Although we should be safe because we haven't yet changed the
clocksource at that time, we can't do that because of seqcount
protection.
Use ktime_get_mono_fast_ns() instead which is lock safe for such
cases.
With ktime_get_mono_fast_ns, the timestamp is not guaranteed to be
monotonic across an update and as a result can goes backward.
According to update_fast_timekeeper() description: "In the worst
case, this can result is a slightly wrong timestamp (a few
nanoseconds)". For PM-runtime autosuspend, this means only that
the suspend decision may be slightly suboptimal.
Fixes: 8234f6734c5d ("PM-runtime: Switch autosuspend over to using hrtimers")
Reported-by: Biju Das <[email protected]>
Signed-off-by: Vincent Guittot <[email protected]>
Reviewed-by: Ulf Hansson <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
The current dentry number tracking code doesn't distinguish between
positive & negative dentries. It just reports the total number of
dentries in the LRU lists.
As excessive number of negative dentries can have an impact on system
performance, it will be wise to track the number of positive and
negative dentries separately.
This patch adds tracking for the total number of negative dentries in
the system LRU lists and reports it in the 5th field in the
/proc/sys/fs/dentry-state file. The number, however, does not include
negative dentries that are in flight but not in the LRU yet as well as
those in the shrinker lists which are on the way out anyway.
The number of positive dentries in the LRU lists can be roughly found by
subtracting the number of negative dentries from the unused count.
Matthew Wilcox had confirmed that since the introduction of the
dentry_stat structure in 2.1.60, the dummy array was there, probably for
future extension. They were not replacements of pre-existing fields.
So no sane applications that read the value of /proc/sys/fs/dentry-state
will do dummy thing if the last 2 fields of the sysctl parameter are not
zero. IOW, it will be safe to use one of the dummy array entry for
negative dentry count.
Signed-off-by: Waiman Long <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
The list_lru structure is essentially just a pointer to a table of
per-node LRU lists. Even if CONFIG_MEMCG_KMEM is defined, the list
field is just used for LRU list registration and shrinker_id is set at
initialization. Those fields won't need to be touched that often.
So there is no point to make the list_lru structures to sit in their own
cachelines.
Signed-off-by: Waiman Long <[email protected]>
Reviewed-by: Dave Chinner <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
The nr_dentry_unused per-cpu counter tracks dentries in both the LRU
lists and the shrink lists where the DCACHE_LRU_LIST bit is set.
The shrink_dcache_sb() function moves dentries from the LRU list to a
shrink list and subtracts the dentry count from nr_dentry_unused. This
is incorrect as the nr_dentry_unused count will also be decremented in
shrink_dentry_list() via d_shrink_del().
To fix this double decrement, the decrement in the shrink_dcache_sb()
function is taken out.
Fixes: 4e717f5c1083 ("list_lru: remove special case function list_lru_dispose_all."
Cc: [email protected]
Signed-off-by: Waiman Long <[email protected]>
Reviewed-by: Dave Chinner <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
After a timeout event caused by for example a broadcast storm, when
the MAC and PHY are reset, the BQL TX queue needs to be reset as
well. Otherwise, the device will exhibit severe performance issues
even after the storm has ended.
Co-authored-by: David Gounaris <[email protected]>
Signed-off-by: Mathias Thore <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
With the following commit:
73d5e2b47264 ("cpu/hotplug: detect SMT disabled by BIOS")
... the hotplug code attempted to detect when SMT was disabled by BIOS,
in which case it reported SMT as permanently disabled. However, that
code broke a virt hotplug scenario, where the guest is booted with only
primary CPU threads, and a sibling is brought online later.
The problem is that there doesn't seem to be a way to reliably
distinguish between the HW "SMT disabled by BIOS" case and the virt
"sibling not yet brought online" case. So the above-mentioned commit
was a bit misguided, as it permanently disabled SMT for both cases,
preventing future virt sibling hotplugs.
Going back and reviewing the original problems which were attempted to
be solved by that commit, when SMT was disabled in BIOS:
1) /sys/devices/system/cpu/smt/control showed "on" instead of
"notsupported"; and
2) vmx_vm_init() was incorrectly showing the L1TF_MSG_SMT warning.
I'd propose that we instead consider #1 above to not actually be a
problem. Because, at least in the virt case, it's possible that SMT
wasn't disabled by BIOS and a sibling thread could be brought online
later. So it makes sense to just always default the smt control to "on"
to allow for that possibility (assuming cpuid indicates that the CPU
supports SMT).
The real problem is #2, which has a simple fix: change vmx_vm_init() to
query the actual current SMT state -- i.e., whether any siblings are
currently online -- instead of looking at the SMT "control" sysfs value.
So fix it by:
a) reverting the original "fix" and its followup fix:
73d5e2b47264 ("cpu/hotplug: detect SMT disabled by BIOS")
bc2d8d262cba ("cpu/hotplug: Fix SMT supported evaluation")
and
b) changing vmx_vm_init() to query the actual current SMT state --
instead of the sysfs control value -- to determine whether the L1TF
warning is needed. This also requires the 'sched_smt_present'
variable to exported, instead of 'cpu_smt_control'.
Fixes: 73d5e2b47264 ("cpu/hotplug: detect SMT disabled by BIOS")
Reported-by: Igor Mammedov <[email protected]>
Signed-off-by: Josh Poimboeuf <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Cc: Joe Mario <[email protected]>
Cc: Jiri Kosina <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: [email protected]
Cc: [email protected]
Link: https://lkml.kernel.org/r/e3a85d585da28cc333ecbc1e78ee9216e6da9396.1548794349.git.jpoimboe@redhat.com
|
|
Johannes Berg says:
====================
various compat ioctl fixes
Back a long time ago, I already fixed a few of these by passing
the size of the struct ifreq to do_sock_ioctl(). However, Robert
found more cases, and now it won't be as simple because we'd have
to pass that down all the way to e.g. bond_do_ioctl() which isn't
really feasible.
Therefore, restore the old code.
While looking at why SIOCGIFNAME was broken, I realized that Al
had removed that case - which had been handled in an explicit
separate function - as well, and looking through his work at the
time I saw that bond ioctls were also affected by the erroneous
removal.
I've restored SIOCGIFNAME and bond ioctls by going through the
(now renamed) dev_ifsioc() instead of reintroducing their own
helper functions, which I hope is correct but have only tested
with SIOCGIFNAME.
====================
Acked-by: Al Viro <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Same story as before, these use struct ifreq and thus need
to be read with the shorter version to not cause faults.
Cc: [email protected]
Fixes: f92d4fc95341 ("kill bond_ioctl()")
Signed-off-by: Johannes Berg <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
As reported by Robert O'Callahan in
https://bugzilla.kernel.org/show_bug.cgi?id=202273
reverting the previous changes in this area broke
the SIOCGIFNAME ioctl in compat again (I'd previously
fixed it after his previous report of breakage in
https://bugzilla.kernel.org/show_bug.cgi?id=199469).
This is obviously because I fixed SIOCGIFNAME more or
less by accident.
Fix it explicitly now by making it pass through the
restored compat translation code.
Cc: [email protected]
Fixes: 4cf808e7ac32 ("kill dev_ifname32()")
Reported-by: Robert O'Callahan <[email protected]>
Signed-off-by: Johannes Berg <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This reverts commit bf4405737f9f ("kill dev_ifsioc()").
This wasn't really unused as implied by the original commit,
it still handles the copy to/from user differently, and the
commit thus caused issues such as
https://bugzilla.kernel.org/show_bug.cgi?id=199469
and
https://bugzilla.kernel.org/show_bug.cgi?id=202273
However, deviating from a strict revert, rename dev_ifsioc()
to compat_ifreq_ioctl() to be clearer as to its purpose and
add a comment.
Cc: [email protected]
Fixes: bf4405737f9f ("kill dev_ifsioc()")
Signed-off-by: Johannes Berg <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This reverts commit 1cebf8f143c2 ("socket: fix struct ifreq
size in compat ioctl"), it's a bugfix for another commit that
I'll revert next.
This is not a 'perfect' revert, I'm keeping some coding style
intact rather than revert to the state with indentation errors.
Cc: [email protected]
Fixes: 1cebf8f143c2 ("socket: fix struct ifreq size in compat ioctl")
Signed-off-by: Johannes Berg <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This reverts commit d4104c5e783f5d053b97268fb92001d785de7dd5.
Turns out it still needs some more work, I merged it to soon :(
Reported-by: Gao Xiang <[email protected]>
Reported-by: Dan Carpenter <[email protected]>
Cc: Al Viro <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
amdgpu only uses shared-fences internally, but dmabuf importers rely on
implicit write hazard tracking via the reservation_object.fence_excl.
For example, the importer use the write hazard for timing a page flip to
only occur after the exporter has finished flushing its write into the
surface. As such, on exporting a dmabuf, we must either flush all
outstanding fences (for we do not know which are writes and should have
been exclusive) or alternatively create a new exclusive fence that is
the composite of all the existing shared fences, and so will only be
signaled when all earlier fences are signaled (ensuring that we can not
be signaled before the completion of any earlier write).
v2: reservation_object is already locked by amdgpu_bo_reserve()
v3: Replace looping with get_fences_rcu and special case the promotion
of a single shared fence directly to an exclusive fence, bypassing the
fence array.
v4: Drop the fence array ref after assigning to reservation_object
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107341
Testcase: igt/amd_prime/amd-to-i915
References: 8e94a46c1770 ("drm/amdgpu: Attach exclusive fence to prime exported bo's. (v5)")
Signed-off-by: Chris Wilson <[email protected]>
Cc: Alex Deucher <[email protected]>
Cc: "Christian König" <[email protected]>
Reviewed-by: "Christian König" <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
"A few more fixes this time:
- Two patches to fix the error path of the map_sg implementation of
the AMD IOMMU driver.
- Also a missing IOTLB flush is fixed in the AMD IOMMU driver.
- Memory leak fix for the Intel IOMMU driver.
- Fix a regression in the Mediatek IOMMU driver which caused device
initialization to fail (seen as broken HDMI output)"
* tag 'iommu-fixes-v5.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Fix IOMMU page flush when detach device from a domain
iommu/mediatek: Use correct fwspec in mtk_iommu_add_device()
iommu/vt-d: Fix memory leak in intel_iommu_put_resv_regions()
iommu/amd: Unmap all mapped pages in error path of map_sg
iommu/amd: Call free_iova_fast with pfn in map_sg
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Here is a bunch of GPIO fixes for the v5.0 series. I was helped out by
Bartosz in collecting these fixes, for which I am very grateful, the
biggest achievement in GPIO right now is work distribution.
There is one serious core fix (timestamping) and a bunch of driver
fixes:
- Fix timestamps on nested IRQs
- Handle IRQs properly in multiple instances of PCF857x
- Use the right data register and IRQ type setting in the Spreadtrum
GPIO driver
- Let the value argument work properly when setting direction in the
Altera GPIO driver
- Mask interrupts properly in the vf610 driver"
* tag 'gpio-v5.0-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: vf610: Mask all GPIO interrupts
gpio: altera-a10sr: Set proper output level for direction_output
gpio: sprd: Fix incorrect irq type setting for the async EIC
gpio: sprd: Fix the incorrect data register
gpiolib: fix line event timestamps for nested irqs
gpio: pcf857x: Fix interrupts on multiple instances
|
|
The subvol_name is allocated in btrfs_parse_subvol_options and is
consumed and freed in mount_subvol. Add a free to the error paths that
don't call mount_subvol so that it is guaranteed that subvol_name is
freed when an error happens.
Fixes: 312c89fbca06 ("btrfs: cleanup btrfs_mount() using btrfs_mount_root()")
Cc: [email protected] # v4.19+
Reviewed-by: Nikolay Borisov <[email protected]>
Signed-off-by: "Eric W. Biederman" <[email protected]>
Reviewed-by: David Sterba <[email protected]>
Signed-off-by: David Sterba <[email protected]>
|
|
The fstests generic/475 stresses transaction aborts and can reveal
space accounting or use-after-free bugs regarding block goups.
In this case the pending block groups that remain linked to the
structures after transaction commit aborts in the middle.
The corrupted slabs lead to failures in following tests, eg. generic/476
[ 8172.752887] BUG: unable to handle kernel NULL pointer dereference at 0000000000000058
[ 8172.755799] #PF error: [normal kernel read fault]
[ 8172.757571] PGD 661ae067 P4D 661ae067 PUD 3db8e067 PMD 0
[ 8172.759000] Oops: 0000 [#1] PREEMPT SMP
[ 8172.760209] CPU: 0 PID: 39 Comm: kswapd0 Tainted: G W 5.0.0-rc2-default #408
[ 8172.762495] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.11.2-0-gf9626cc-prebuilt.qemu-project.org 04/01/2014
[ 8172.765772] RIP: 0010:shrink_page_list+0x2f9/0xe90
[ 8172.770453] RSP: 0018:ffff967f00663b18 EFLAGS: 00010287
[ 8172.771184] RAX: 0000000000000000 RBX: ffff967f00663c20 RCX: 0000000000000000
[ 8172.772850] RDX: 0000000000000000 RSI: 0000000000000001 RDI: ffff8c0620ab20e0
[ 8172.774629] RBP: ffff967f00663dd8 R08: 0000000000000000 R09: 0000000000000000
[ 8172.776094] R10: ffff8c0620ab22f8 R11: ffff8c063f772688 R12: ffff967f00663b78
[ 8172.777533] R13: ffff8c063f625600 R14: ffff8c063f625608 R15: dead000000000200
[ 8172.778886] FS: 0000000000000000(0000) GS:ffff8c063d400000(0000) knlGS:0000000000000000
[ 8172.780545] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 8172.781787] CR2: 0000000000000058 CR3: 000000004e962000 CR4: 00000000000006f0
[ 8172.783547] Call Trace:
[ 8172.784112] shrink_inactive_list+0x194/0x410
[ 8172.784747] shrink_node_memcg.constprop.85+0x3a5/0x6a0
[ 8172.785472] shrink_node+0x62/0x1e0
[ 8172.786011] balance_pgdat+0x216/0x460
[ 8172.786577] kswapd+0xe3/0x4a0
[ 8172.787085] ? finish_wait+0x80/0x80
[ 8172.787795] ? balance_pgdat+0x460/0x460
[ 8172.788799] kthread+0x116/0x130
[ 8172.789640] ? kthread_create_on_node+0x60/0x60
[ 8172.790323] ret_from_fork+0x24/0x30
[ 8172.794253] CR2: 0000000000000058
or accounting errors at umount time:
[ 8159.537251] WARNING: CPU: 2 PID: 19031 at fs/btrfs/extent-tree.c:5987 btrfs_free_block_groups+0x3d5/0x410 [btrfs]
[ 8159.543325] CPU: 2 PID: 19031 Comm: umount Tainted: G W 5.0.0-rc2-default #408
[ 8159.545472] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.11.2-0-gf9626cc-prebuilt.qemu-project.org 04/01/2014
[ 8159.548155] RIP: 0010:btrfs_free_block_groups+0x3d5/0x410 [btrfs]
[ 8159.554030] RSP: 0018:ffff967f079cbde8 EFLAGS: 00010206
[ 8159.555144] RAX: 0000000001000000 RBX: ffff8c06366cf800 RCX: 0000000000000000
[ 8159.556730] RDX: 0000000000000002 RSI: 0000000000000001 RDI: ffff8c06255ad800
[ 8159.558279] RBP: ffff8c0637ac0000 R08: 0000000000000001 R09: 0000000000000000
[ 8159.559797] R10: 0000000000000000 R11: 0000000000000001 R12: ffff8c0637ac0108
[ 8159.561296] R13: ffff8c0637ac0158 R14: 0000000000000000 R15: dead000000000100
[ 8159.562852] FS: 00007f7f693b9fc0(0000) GS:ffff8c063d800000(0000) knlGS:0000000000000000
[ 8159.564839] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 8159.566160] CR2: 00007f7f68fab7b0 CR3: 000000000aec7000 CR4: 00000000000006e0
[ 8159.567898] Call Trace:
[ 8159.568597] close_ctree+0x17f/0x350 [btrfs]
[ 8159.569628] generic_shutdown_super+0x64/0x100
[ 8159.570808] kill_anon_super+0x14/0x30
[ 8159.571857] btrfs_kill_super+0x12/0xa0 [btrfs]
[ 8159.573063] deactivate_locked_super+0x29/0x60
[ 8159.574234] cleanup_mnt+0x3b/0x70
[ 8159.575176] task_work_run+0x98/0xc0
[ 8159.576177] exit_to_usermode_loop+0x83/0x90
[ 8159.577315] do_syscall_64+0x15b/0x180
[ 8159.578339] entry_SYSCALL_64_after_hwframe+0x49/0xbe
This fix is based on 2 Josef's patches that used sideefects of
btrfs_create_pending_block_groups, this fix introduces the helper that
does what we need.
CC: [email protected] # 4.4+
CC: Josef Bacik <[email protected]>
Reviewed-by: Nikolay Borisov <[email protected]>
Signed-off-by: David Sterba <[email protected]>
|
|
alloc_fs_devices() can return ERR_PTR(-ENOMEM), so dereferencing its
result before the check for IS_ERR() is a bad idea.
Fixes: d1a63002829a4 ("btrfs: add members to fs_devices to track fsid changes")
Reviewed-by: Nikolay Borisov <[email protected]>
Reviewed-by: Anand Jain <[email protected]>
Signed-off-by: Al Viro <[email protected]>
Reviewed-by: David Sterba <[email protected]>
Signed-off-by: David Sterba <[email protected]>
|
|
Florian reported a io hung issue when fsync(). It should be
triggered by following race condition.
data + post flush a flush
blk_flush_complete_seq
case REQ_FSEQ_DATA
blk_flush_queue_rq
issued to driver blk_mq_dispatch_rq_list
try to issue a flush req
failed due to NON-NCQ command
.queue_rq return BLK_STS_DEV_RESOURCE
request completion
req->end_io // doesn't check RESTART
mq_flush_data_end_io
case REQ_FSEQ_POSTFLUSH
blk_kick_flush
do nothing because previous flush
has not been completed
blk_mq_run_hw_queue
insert rq to hctx->dispatch
due to RESTART is still set, do nothing
To fix this, replace the blk_mq_run_hw_queue in mq_flush_data_end_io
with blk_mq_sched_restart to check and clear the RESTART flag.
Fixes: bd166ef1 (blk-mq-sched: add framework for MQ capable IO schedulers)
Reported-by: Florian Stecker <[email protected]>
Tested-by: Florian Stecker <[email protected]>
Signed-off-by: Jianchao Wang <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
syzbot is hitting flush_work() warning caused by commit 4d43d395fed12463
("workqueue: Try to catch flush_work() without INIT_WORK().") [1].
Although that commit did not expect INIT_WORK(NULL) case, calling
flush_work() without setting a valid callback should be avoided anyway.
Fix this problem by setting a no-op callback instead of NULL.
[1] https://syzkaller.appspot.com/bug?id=e390366bc48bc82a7c668326e0663be3b91cbd29
Signed-off-by: Tetsuo Handa <[email protected]>
Reported-and-tested-by: syzbot <[email protected]>
Cc: Tejun Heo <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
Handling short packets (length < max packet size) in the Inventra DMA
engine in the MUSB driver causes the MUSB DMA controller to hang. An
example of a problem that is caused by this problem is when streaming
video out of a UVC gadget, only the first video frame is transferred.
For short packets (mode-0 or mode-1 DMA), MUSB_TXCSR_TXPKTRDY must be
set manually by the driver. This was previously done in musb_g_tx
(musb_gadget.c), but incorrectly (all csr flags were cleared, and only
MUSB_TXCSR_MODE and MUSB_TXCSR_TXPKTRDY were set). Fixing that problem
allows some requests to be transferred correctly, but multiple requests
were often put together in one USB packet, and caused problems if the
packet size was not a multiple of 4. Instead, set MUSB_TXCSR_TXPKTRDY
in dma_controller_irq (musbhsdma.c), just like host mode transfers.
This topic was originally tackled by Nicolas Boichat [0] [1] and is
discussed further at [2] as part of his GSoC project [3].
[0] https://groups.google.com/forum/?hl=en#!topic/beagleboard-gsoc/k8Azwfp75CU
[1] https://gitorious.org/beagleboard-usbsniffer/beagleboard-usbsniffer-kernel/commit/b0be3b6cc195ba732189b04f1d43ec843c3e54c9?p=beagleboard-usbsniffer:beagleboard-usbsniffer-kernel.git;a=patch;h=b0be3b6cc195ba732189b04f1d43ec843c3e54c9
[2] http://beagleboard-usbsniffer.blogspot.com/2010/07/musb-isochronous-transfers-fixed.html
[3] http://elinux.org/BeagleBoard/GSoC/USBSniffer
Fixes: 550a7375fe72 ("USB: Add MUSB and TUSB support")
Signed-off-by: Paul Elder <[email protected]>
Signed-off-by: Bin Liu <[email protected]>
Cc: stable <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
VOP is broken in mainline since commit 1ce9e6055fa0a9043 ("virtio_ring:
introduce packed ring support"); attempting to use the virtqueues leads
to various kernel crashes. I'm testing it with my not-yet-merged
loopback patches, but even the in-tree MIC hardware cannot work.
The problem is not in the referenced commit per se, but is due to the
following hack in vop_find_vq() which depends on the layout of private
structures in other source files, which that commit happened to change:
/*
* To reassign the used ring here we are directly accessing
* struct vring_virtqueue which is a private data structure
* in virtio_ring.c. At the minimum, a BUILD_BUG_ON() in
* vring_new_virtqueue() would ensure that
* (&vq->vring == (struct vring *) (&vq->vq + 1));
*/
vr = (struct vring *)(vq + 1);
vr->used = used;
Fix vop by using __vring_new_virtqueue() to create the needed vring
layout from the start, instead of attempting to patch in the used ring
later. __vring_new_virtqueue() was added way back in commit
2a2d1382fe9dcc ("virtio: Add improved queue allocation API") in order to
address mic's usecase, according to the commit message.
Fixes: 1ce9e6055fa0 ("virtio_ring: introduce packed ring support")
Signed-off-by: Vincent Whitchurch <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
As Al pointed out, "
... and while we are at it, what happens to
unsigned int nameoff = le16_to_cpu(de[mid].nameoff);
unsigned int matched = min(startprfx, endprfx);
struct qstr dname = QSTR_INIT(data + nameoff,
unlikely(mid >= ndirents - 1) ?
maxsize - nameoff :
le16_to_cpu(de[mid + 1].nameoff) - nameoff);
/* string comparison without already matched prefix */
int ret = dirnamecmp(name, &dname, &matched);
if le16_to_cpu(de[...].nameoff) is not monotonically increasing? I.e.
what's to prevent e.g. (unsigned)-1 ending up in dname.len?
Corrupted fs image shouldn't oops the kernel.. "
Revisit the related lookup flow to address the issue.
Fixes: d72d1ce60174 ("staging: erofs: add namei functions")
Cc: <[email protected]> # 4.19+
Suggested-by: Al Viro <[email protected]>
Signed-off-by: Gao Xiang <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Commit 2b3e88ea6528 ("net: phy: improve phy state checking")
added checks for phylib usage, and this triggers with OCTEON ethernet
and results in broken networking.
Fix by replacing phy_start_aneg() with phy_start().
Fixes: 2b3e88ea6528 ("net: phy: improve phy state checking")
Signed-off-by: Aaro Koskinen <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
There is a little window during disconnection flow
when read cb is moved between lists and may be not freed.
Remove moving read cbs explicitly during flash fixes this memory
leak.
Signed-off-by: Alexander Usyskin <[email protected]>
Signed-off-by: Tomas Winkler <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The device was moved from misc device to character devices
to support multiple mei devices.
Cc: <[email protected]> #v4.9+
Signed-off-by: Tomas Winkler <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Add icelake mei device id.
Cc: <[email protected]>
Signed-off-by: Tomas Winkler <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
We currently adhere to the reserved devices limit when creating new
binderfs devices in binderfs instances not located in the inital ipc
namespace. But it is still possible to rob the host instances of their 4
reserved devices by creating the maximum allowed number of devices in a
single binderfs instance located in a non-initial ipc namespace and then
mounting 4 separate binderfs instances in non-initial ipc namespaces. That
happens because the limit is currently not respected for the creation of
the initial binder-control device node. Block this nonsense by performing
the same check in binderfs_binder_ctl_create() that we perform in
binderfs_binder_device_create().
Fixes: 36bdf3cae09d ("binderfs: reserve devices for initial mount")
Signed-off-by: Christian Brauner <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|