| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Parses a simple DAPM route table from device tree.
Signed-off-by: Xiubo Li <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
|
|
When call snd_soc_register_card, it will set driver data to this
device through dev_set_drvdata, then in driver, no need to call
platform_set_drvdata again, so remove it.
Signed-off-by: Bo Shen <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
|
|
Revert the SAI's endianess for fifo data to/from DMA engine.
Signed-off-by: Xiubo Li <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
|
|
This is maybe one bug or a limitation of the hardware that the {T,R}CR2's
Synchronous Mode bits must be set as late as possible, or the SAI device
maybe hanged up, and there has not any explaination about this limitation
in the SAI Data Sheet.
And the {T,R}CR2's Synchronous Mode bits must be set at the same time whether
for Tx or Rx stream.
Signed-off-by: Xiubo Li <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
|
|
The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.
Signed-off-by: Lars-Peter Clausen <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
|
|
The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.
Signed-off-by: Lars-Peter Clausen <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
|
|
The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.
Signed-off-by: Lars-Peter Clausen <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
|
|
The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.
Signed-off-by: Lars-Peter Clausen <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
|
|
The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.
Signed-off-by: Lars-Peter Clausen <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
|
|
Add helpers for obtaining the width of a format directly from params
since this is expected to become a common operation in ASoC.
Signed-off-by: Mark Brown <[email protected]>
Reviewed-by: Takashi Iwai <[email protected]>
|
|
Enables/Disables the corresponding data channel for tx/rx operation.
A channel must be enabled before its FIFO is accessed, and then disable
it when tx/rx is stopped or idle.
Signed-off-by: Xiubo Li <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
|
|
commit 5d229ce569be ("ASoC: samsung: move plat/ headers to local directory")
moved the header files but forgot to clean the pointers to their old locaton.
Remove them now.
Signed-off-by: Sachin Kamat <[email protected]>
Reviewed-by: Jingoo Han <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
|
|
Because we cannot make sure which one of _dai_fmt() and _dai_sysclk()
will be firstly called. So move the RCSR/TCSR and TCR1/RCR1's
initialization to _dai_probe(), and this can make sure that before any
of {T,R}CR{1~5} register to be set the RCSR/TCSR's RE/TE bit has been
cleared for the hareware limitation.
Signed-off-by: Xiubo Li <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
|
|
Commit 2203747c9771 ("ARM: omap: move platform_data definitions")
moved the file to the current location but forgot to remove the pointer
to its previous location. Clean it up. While at it also change the header
file protection macros appropriately.
Signed-off-by: Sachin Kamat <[email protected]>
Acked-by: Peter Ujfalusi <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Another smallish batch of fixes, it's been quiet due to the holidays.
Nothing controversial here, a handful of things across the board"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: pxa: fix USB gadget driver compilation regression
ARM: OMAP2+: Fix LCD panel backlight regression for LDP legacy booting
ARM: OMAP2+: hwmod_data: fix missing OMAP_INTC_START in irq data
ARM: DRA7: hwmod: Fix boot crash with DEBUG_LL
ARM: shmobile: r8a7790: fix shdi resource sizes
ARM: shmobile: bockw: fixup DMA mask
ARM: shmobile: armadillo: Add PWM backlight power supply
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Peter Anvin:
"There is a small EFI fix and a big power regression fix in this batch.
My queue also had a fix for downing a CPU when there are insufficient
number of IRQ vectors available, but I'm holding that one for now due
to recent bug reports"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/efi: Don't select EFI from certain special ACPI drivers
x86 idle: Repair large-server 50-watt idle-power regression
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes and new device IDs from Rafael Wysocki:
- Fix for a cpufreq regression causing stale sysfs files to be left
behind during system resume if cpufreq_add_dev() fails for one or
more CPUs from Viresh Kumar.
- Fix for a bug in cpufreq causing CONFIG_CPU_FREQ_DEFAULT_* to be
ignored when the intel_pstate driver is used from Jason Baron.
- System suspend fix for a memory leak in pm_vt_switch_unregister()
that forgot to release objects after removing them from
pm_vt_switch_list. From Masami Ichikawa.
- Intel Valley View device ID and energy unit encoding update for the
(recently added) Intel RAPL (Running Average Power Limit) driver from
Jacob Pan.
- Intel Bay Trail SoC GPIO and ACPI device IDs for the Low Power
Subsystem (LPSS) ACPI driver from Paul Drews.
* tag 'pm+acpi-3.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
powercap / RAPL: add support for ValleyView Soc
PM / sleep: Fix memory leak in pm_vt_switch_unregister().
cpufreq: Use CONFIG_CPU_FREQ_DEFAULT_* to set initial policy for setpolicy drivers
cpufreq: remove sysfs files for CPUs which failed to come back after resume
ACPI: Add BayTrail SoC GPIO and LPSS ACPI IDs
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
Fix a regression for wrong interrupt numbers for some devices after
the sparse IRQ conversion, fix DRA7 console output for earlyprintk,
and fix the LDP LCD backlight when DSS is built into the kernel and
not as a loadable module.
* tag 'omap-for-v3.13/intc-ldp-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix LCD panel backlight regression for LDP legacy booting
ARM: OMAP2+: hwmod_data: fix missing OMAP_INTC_START in irq data
ARM: DRA7: hwmod: Fix boot crash with DEBUG_LL
+ v3.13-rc5
Signed-off-by: Olof Johansson <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
From Simon Horman:
Second Round of Renesas ARM based SoC Fixes for v3.13
* r8a7790 (R-Car H2) based Lager board
- Correct SHDI resource sizes
This bug has been present since sdhi resources were added to the r8a7790 by
8c9b1aa41853272a ("ARM: shmobile: r8a7790: add MMCIF and SDHI DT
templates") in v3.11-rc2.
* r8a7778 (R-Car M1) based Bock-W board
- Correct DMA mask
This resolves a regression introduced by 4dcfa60071b3d23f
("ARM: DMA-API: better handing of DMA masks for coherent allocations")
in v3.12-rc1.
* r8a7740 (R-Mobile A1) based Armadillo board
- Add PWM backlight power supply
This resolves a regression introduced by 22ceeee16eb8f0d0
("pwm-backlight: Add power supply support") in v3.12.
* tag 'renesas-fixes2-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7790: fix shdi resource sizes
ARM: shmobile: bockw: fixup DMA mask
ARM: shmobile: armadillo: Add PWM backlight power supply
Signed-off-by: Olof Johansson <[email protected]>
Signed-off-by: Olof Johansson <[email protected]>
|
|
After commit 88f718e3fa4d67f3a8dbe79a2f97d722323e4051
"ARM: pxa: delete the custom GPIO header" a compilation
error was introduced in the PXA25x gadget driver.
An attempt to fix the problem was made in
commit b144e4ab1ef130e8bf30bcd3e529b7f35112c503
"usb: gadget: fix pxa25x compilation problems"
by explictly stating the driver needs the <mach/hardware.h>
header, which solved the compilation for a few boards,
such as the pxa255-idp and its defconfig.
However the Lubbock board has this special clause in
drivers/usb/gadget/pxa25x_udc.c:
This include file has an implicit dependency on
<mach/irqs.h> having been included before <mach/lubbock.h>
was included.
Before commit 88f718e3fa4d67f3a8dbe79a2f97d722323e4051
"ARM: pxa: delete the custom GPIO header" this implicit
dependency for the pxa25x_udc compile on the Lubbock was
satisfied by <linux/gpio.h> implicitly including
<mach/gpio.h> which was in turn including <mach/irqs.h>,
apart from the earlier added <mach/hardware.h>.
Fix this by having the PXA25x <mach/lubbock.h> explicitly
include <mach/irqs.h>.
Reported-by: Russell King <[email protected]>
Cc: Greg Kroah-Hartmann <[email protected]>
Cc: Felipe Balbi <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
Signed-off-by: Haojian Zhuang <[email protected]>
Signed-off-by: Olof Johansson <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into debug-ll-and-ldp-backlight-fix
A few OMAP hwmod fixes for v3.13-rc. One patch fixes some IRQ
problems with GPMC, RNG, and ISP/IVA MMUs on OMAP2/3. The other fixes
some problems with DEBUG_LL on DRA7xx.
Basic build, boot, and PM test logs are available here:
http://www.pwsan.com/omap/testlogs/hwmod_fixes_b_v3.13-rc/20131226021920/
|
|
Looks like the LCD panel on LDP has been broken quite a while, and
recently got fixed by commit 0b2aa8bed3e1 (gpio: twl4030: Fix regression
for twl gpio output). However, there's still an issue left where the panel
backlight does not come on if the LCD drivers are built into the
kernel.
Fix the issue by registering the DPI LCD panel only after the twl4030
GPIO has probed.
Reported-by: Russell King <[email protected]>
Acked-by: Tomi Valkeinen <[email protected]>
[[email protected]: updated per Tomi's comments]
Signed-off-by: Tony Lindgren <[email protected]>
|
|
* powercap:
powercap / RAPL: add support for ValleyView Soc
* acpi-lpss:
ACPI: Add BayTrail SoC GPIO and LPSS ACPI IDs
|
|
* pm-cpufreq:
cpufreq: Use CONFIG_CPU_FREQ_DEFAULT_* to set initial policy for setpolicy drivers
cpufreq: remove sysfs files for CPUs which failed to come back after resume
* pm-sleep:
PM / sleep: Fix memory leak in pm_vt_switch_unregister().
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"A collection of bug fixes destined for stable and some printk cleanups
and a patch so that instead of BUG'ing we use the ext4_error()
framework to mark the file system is corrupted"
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: add explicit casts when masking cluster sizes
ext4: fix deadlock when writing in ENOSPC conditions
jbd2: rename obsoleted msg JBD->JBD2
jbd2: revise KERN_EMERG error messages
jbd2: don't BUG but return ENOSPC if a handle runs out of space
ext4: Do not reserve clusters when fs doesn't support extents
ext4: fix del_timer() misuse for ->s_err_report
ext4: check for overlapping extents in ext4_valid_extent_entries()
ext4: fix use-after-free in ext4_mb_new_blocks
ext4: call ext4_error_inode() if jbd2_journal_dirty_metadata() fails
|
|
Commit 7d7e1eb (ARM: OMAP2+: Prepare for irqs.h removal) and commit
ec2c082 (ARM: OMAP2+: Remove hardcoded IRQs and enable SPARSE_IRQ)
updated the way interrupts for OMAP2/3 devices are defined in the
HWMOD data structures to being an index plus a fixed offset (defined
by OMAP_INTC_START).
Couple of irqs in the OMAP2/3 hwmod data were misconfigured completely
as they were missing this OMAP_INTC_START relative offset. Add this
offset back to fix the incorrect irq data for the following modules:
OMAP2 - GPMC, RNG
OMAP3 - GPMC, ISP MMU & IVA MMU
Signed-off-by: Suman Anna <[email protected]>
Fixes: 7d7e1eba7e92 ("ARM: OMAP2+: Prepare for irqs.h removal")
Fixes: ec2c0825ca31 ("ARM: OMAP2+: Remove hardcoded IRQs and enable SPARSE_IRQ")
Cc: Tony Lindgren <[email protected]>
Signed-off-by: Paul Walmsley <[email protected]>
|
|
With commit '7dedd34: ARM: OMAP2+: hwmod: Fix a crash in _setup_reset() with
DEBUG_LL' we moved from parsing cmdline to identify uart used for earlycon
to using the requsite hwmod CONFIG_DEBUG_OMAPxUARTy FLAGS.
On DRA7 though, we seem to be missing this flag, and atleast on the DRA7 EVM
where we use uart1 for console, boot fails with DEBUG_LL enabled.
Reported-by: Lokesh Vutla <[email protected]>
Tested-by: Lokesh Vutla <[email protected]> # on a different base
Signed-off-by: Rajendra Nayak <[email protected]>
Fixes: 7dedd346941d ("ARM: OMAP2+: hwmod: Fix a crash in _setup_reset() with DEBUG_LL")
Signed-off-by: Paul Walmsley <[email protected]>
|
|
Pull block fixes from Jens Axboe:
- fix for a memory leak on certain unplug events
- a collection of bcache fixes from Kent and Nicolas
- a few null_blk fixes and updates form Matias
- a marking of static of functions in the stec pci-e driver
* 'for-linus' of git://git.kernel.dk/linux-block:
null_blk: support submit_queues on use_per_node_hctx
null_blk: set use_per_node_hctx param to false
null_blk: corrections to documentation
null_blk: warning on ignored submit_queues param
null_blk: refactor init and init errors code paths
null_blk: documentation
null_blk: mem garbage on NUMA systems during init
drivers: block: Mark the functions as static in skd_main.c
bcache: New writeback PD controller
bcache: bugfix for race between moving_gc and bucket_invalidate
bcache: fix for gc and writeback race
bcache: bugfix - moving_gc now moves only correct buckets
bcache: fix for gc crashing when no sectors are used
bcache: Fix heap_peek() macro
bcache: Fix for can_attach_cache()
bcache: Fix dirty_data accounting
bcache: Use uninterruptible sleep in writeback
bcache: kthread don't set writeback task to INTERUPTIBLE
block: fix memory leaks on unplugging block device
bcache: fix sparse non static symbol warning
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fixes from Tejun Heo:
"Two fixes. One fixes a bug in the error path of cgroup_create(). The
other changes cgrp->id lifetime rule so that the id doesn't get
recycled before all controller states are destroyed. This premature
id recycling made memcg malfunction"
* 'for-3.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: don't recycle cgroup id until all csses' have been destroyed
cgroup: fix cgroup_create() error handling path
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu
Pull percpu fix from Tejun Heo:
"A single commit to fix a spurious sparse warning coming from
DEFINE_PER_CPU()'s hack to support the use of weak symbols. Shouldn't
cause observable behavior change"
* 'for-3.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu: fix spurious sparse warnings from DEFINE_PER_CPU()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"There's one interseting commit - "libata, freezer: avoid block device
removal while system is frozen". It's an ugly hack working around a
deadlock condition between driver core resume and block layer device
removal paths through freezer which was made more reproducible by
writeback being converted to workqueue some releases ago. The bug has
nothing to do with libata but it's just an workaround which is easy to
backport. After discussion, Rafael and I seem to agree that we don't
really need kernel freezables - both kthread and workqueue. There are
few specific workqueues which constitute PM operations and require
freezing, which will be converted to use workqueue_set_max_active()
instead. All other kernel freezer uses are planned to be removed,
followed by the removal of kthread and workqueue freezer support,
hopefully.
Others are device-specific fixes. The most notable is the addition of
NO_NCQ_TRIM which is used to disable queued TRIM commands to Micro
M500 SSDs which otherwise suffers data corruption"
* 'for-3.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata, freezer: avoid block device removal while system is frozen
libata: implement ATA_HORKAGE_NO_NCQ_TRIM and apply it to Micro M500 SSDs
libata: disable a disk via libata.force params
ahci: bail out on ICH6 before using AHCI BAR
ahci: imx: Explicitly clear IMX6Q_GPR13_SATA_MPLL_CLK_EN
libata: add ATA_HORKAGE_BROKEN_FPDMA_AA quirk for Seagate Momentus SpinPoint M8
|
|
Commit 2171364d1a92 ("powerpc: Add HWCAP2 aux entry") introduced a new
AT_ auxv entry type AT_HWCAP2 but failed to update AT_VECTOR_SIZE_BASE
accordingly.
Signed-off-by: Ard Biesheuvel <[email protected]>
Fixes: 2171364d1a92 (powerpc: Add HWCAP2 aux entry)
Cc: [email protected]
Acked-by: Michael Neuling <[email protected]>
Cc: Nishanth Aravamudan <[email protected]>
Cc: Benjamin Herrenschmidt <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.
Signed-off-by: Lars-Peter Clausen <[email protected]>
Acked-by: Peter Ujfalusi <[email protected]>
Acked-by: Jarkko Nikula <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
|
|
The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.
Signed-off-by: Lars-Peter Clausen <[email protected]>
Acked-by: Daniel Glöckner <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
|
|
The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.
Signed-off-by: Lars-Peter Clausen <[email protected]>
Acked-by: Peter Ujfalusi <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull SELinux fixes from James Morris.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
selinux: selinux_setprocattr()->ptrace_parent() needs rcu_read_lock()
selinux: fix broken peer recv check
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Pull ext2 fix from Jan Kara:
"One simple fix of oops in ext2 which was recently hit by Christoph"
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
ext2: Fix oops in ext2_get_block() called from ext2_quota_write()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband fixes from Roland Dreier:
"Last batch of InfiniBand/RDMA changes for 3.13 / 2014:
- Additional checks for uverbs to ensure forward compatibility,
handle malformed input better.
- Fix potential use-after-free in iWARP connection manager.
- Make a function static"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/uverbs: Check access to userspace response buffer in extended command
IB/uverbs: Check input length in flow steering uverbs
IB/uverbs: Set error code when fail to consume all flow_spec items
IB/uverbs: Check reserved fields in create_flow
IB/uverbs: Check comp_mask in destroy_flow
IB/uverbs: Check reserved field in extended command header
IB/uverbs: New macro to set pointers to NULL if length is 0 in INIT_UDATA()
IB/core: const'ify inbuf in struct ib_udata
RDMA/iwcm: Don't touch cm_id after deref in rem_ref
RDMA/cxgb4: Make _c4iw_write_mem_dma() static
|
|
selinux_setprocattr() does ptrace_parent(p) under task_lock(p),
but task_struct->alloc_lock doesn't pin ->parent or ->ptrace,
this looks confusing and triggers the "suspicious RCU usage"
warning because ptrace_parent() does rcu_dereference_check().
And in theory this is wrong, spin_lock()->preempt_disable()
doesn't necessarily imply rcu_read_lock() we need to access
the ->parent.
Reported-by: Evan McNabb <[email protected]>
Signed-off-by: Oleg Nesterov <[email protected]>
Cc: [email protected]
Signed-off-by: Paul Moore <[email protected]>
|
|
Fix a broken networking check. Return an error if peer recv fails. If
secmark is active and the packet recv succeeds the peer recv error is
ignored.
Signed-off-by: Chad Hanson <[email protected]>
Cc: [email protected]
Signed-off-by: Paul Moore <[email protected]>
|
|
Pull drm fixes from Dave Airlie:
"Xmas fixes pull, all small nothing major, intel, radeon, one ttm
regression, and one build fix"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/ttm: Fix swapin regression
gpu: fix qxl missing crc32_le
drm/radeon: fix asic gfx values for scrapper asics
drm/i915: Use the correct GMCH_CTRL register for Sandybridge+
drm/radeon: check for 0 count in speaker allocation and SAD code
drm/radeon/dpm: disable ss on Cayman
drm/radeon/dce6: set correct number of audio pins
drm/i915: get a PC8 reference when enabling the power well
drm/i915: change CRTC assertion on LCPLL disable
drm/i915: Fix erroneous dereference of batch_obj inside reset_status
drm/i915: Prevent double unref following alloc failure during execbuffer
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio balloon driver fixes from Rusty Russell:
"Refactoring broke the balloon driver, and fixing kallsyms on ARM broke
some (non-ARM) MMUless setups, so we're making that fix ARM-only for
now.
Unfortunately, the ARM refactoring which broke kallsyms/perf was
CC:stable, so the fix (which broken non-ARM) was also CC:stable, so
now the partial reversion is also CC:stable..."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
scripts/link-vmlinux.sh: only filter kernel symbols for arm
virtio_balloon: update_balloon_size(): update correct field
|
|
|
|
The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.
Signed-off-by: Lars-Peter Clausen <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
|
|
The Vaughan device support the 352800 rate and not
the 352000
Signed-off-by: Michael Trimarchi <[email protected]>
Signed-off-by: Takashi Iwai <[email protected]>
|
|
git://people.freedesktop.org/~danvet/drm-intel into drm-fixes
Besides the 2 fixes for tricky corner cases in gem from Chris I've
promised already two patche from Paulo to fix pc8 warnings (both ported
from -next, bug report from Dave Jones) and one patch from to fix vga
enable/disable on snb+. That one is a really old bug, but apparently it
can cause machine hangs if you try hard enough with vgacon/efifb handover.
* tag 'drm-intel-fixes-2013-12-18' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Use the correct GMCH_CTRL register for Sandybridge+
drm/i915: get a PC8 reference when enabling the power well
drm/i915: change CRTC assertion on LCPLL disable
drm/i915: Fix erroneous dereference of batch_obj inside reset_status
drm/i915: Prevent double unref following alloc failure during execbuffer
|
|
into drm-fixes
- fix for a long standing corruption bug on some Trinity/Richland parts.
- Stability fix for cayman dpm
- audio fixes for dce6+
* 'drm-fixes-3.13' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix asic gfx values for scrapper asics
drm/radeon: check for 0 count in speaker allocation and SAD code
drm/radeon/dpm: disable ss on Cayman
drm/radeon/dce6: set correct number of audio pins
|
|
Commit "drm/ttm: Don't move non-existing data" didn't take the
swapped-out corner case into account. This patch corrects that.
Fixes blank screen after attempted suspend / hibernate on vmwgfx.
Signed-off-by: Thomas Hellstrom <[email protected]>
Signed-off-by: Dave Airlie <[email protected]>
|
|
Fix build error: qxl uses crc32 functions so it needs to select
CRC32.
Also use angle quotes around a kernel header file name.
drivers/built-in.o: In function `qxl_display_read_client_monitors_config':
(.text+0x19d754): undefined reference to `crc32_le'
Signed-off-by: Randy Dunlap <[email protected]>
Signed-off-by: Dave Airlie <[email protected]>
|