| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM changes for v5.8
1. Add DTS for Exynos4210-based Samsung Galaxy S2 (GT-I9100)
mobile phone,
2. Enable WiFi and Bluetooth in multiple boards,
3. Add new features to S5Pv210-based Aries family of mobile phones
(e.g. Samsung Galaxy S): necessary configuration for suspend, audio
support, USB mux, touch keys, panel, i2c-gpio adapters, FM radio, ADC,
4. Many minor fixes (e.g. GPIO polarity, interrupts).
* tag 'samsung-dt-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (29 commits)
ARM: dts: s5pv210: Set MAX8998 GPIO pulls on Aries boards
ARM: dts: s5pv210: Correct FIMC definitions
ARM: dts: s5pv210: Assign clocks to MMC devices on Aries boards
ARM: dts: s5pv210: Enable ADC on Aries boards
ARM: dts: s5pv210: Add an ADC node
ARM: dts: s5pv210: Disable pull for vibrator enable GPIO on Aries boards
ARM: dts: s5pv210: Add si470x FM radio to Galaxy S
ARM: dts: s5pv210: Add remaining i2c-gpio adapters to Aries boards
ARM: dts: s5pv210: Add panel support to Aries boards
ARM: dts: s5pv210: Add touchkey support to Aries boards
ARM: dts: s5pv210: Add FSA9480 support to Aries boards
ARM: dts: s5pv210: Add WM8994 support to Aries boards
ARM: dts: s5pv210: Disable pulls on GPIO I2C adapters for Aries
ARM: dts: s5pv210: Set keep-power-in-suspend for SDHCI1 on Aries
ARM: dts: s5pv210: Correct gpi pinctrl node name
ARM: dts: s5pv210: Add sleep GPIO configuration for Galaxy S
ARM: dts: s5pv210: Add sleep GPIO configuration for Fascinate4G
ARM: dts: s5pv210: Add helper define for sleep gpio config
ARM: dts: exynos: Enable WLAN support for the UniversalC210 board
ARM: dts: exynos: Enable WLAN support for the Rinato board
...
Link: https://lore.kernel.org/r/20200512122922.5700-2-krzk@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://github.com/Broadcom/stblinux into arm/dt
This pull request contains Broadcom ARM-based SoCs Device Tree changes
for v5.8, please pull the following:
- Nicolas updates the Raspberry Pi 4 board DTS to include the GPIO
controlling power to the SD card, adds support for the vmmc regulator
for the emmc2 controller and finally updates the power management
provider for V3D to use the firmware to solve instabilities.
* tag 'arm-soc/for-5.8/devicetree' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm283x: Use firmware PM driver for V3D
ARM: dts: bcm2711: Add vmmc regulator in emmc2
ARM: dts: bcm2711: Update expgpio's GPIO labels
Link: https://lore.kernel.org/r/20200511210522.28243-2-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
into arm/dt
ARM64: DT: Hisilicon SoCs DT updates for 5.8
- Add pinconf for spi2 and spi3 nodes and increase the drive
strength to achieve the max speed for the Hikey960 board
- Add CTI nodes for the Hikey620 board
* tag 'hisi-arm64-dt-for-5.8' of git://github.com/hisilicon/linux-hisi:
arm64: dts: hi6220: Add CTI options
arm64: dts: hikey960: pinctrl: Fix spi2/spi3 pinconf
Link: https://lore.kernel.org/r/5EBE430E.6090508@hisilicon.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/afaerber/linux-realtek into arm/dt
Realtek Arm based SoC DT for v5.8
Add RTD1195, RTD1395 and RTD1619 SoCs as well as Xnano X5 TV box.
Clean up memory nodes and /soc ranges. Factor out r-bus and partition it
into CRT, Iso, Misc, SB2 and SCPU Wrapper blocks.
* tag 'realtek-dt-for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/afaerber/linux-realtek: (35 commits)
dt-bindings: reset: rtd1295: Add SB2 reset
arm64: dts: realtek: rtd16xx: Add SB2 and SCPU Wrapper syscon nodes
arm64: dts: realtek: rtd139x: Add SB2 and SCPU Wrapper syscon nodes
arm64: dts: realtek: rtd129x: Add SB2 and SCPU Wrapper syscon nodes
ARM: dts: rtd1195: Add SB2 and SCPU Wrapper syscon nodes
arm64: dts: realtek: rtd16xx: Add CRT syscon node
ARM: dts: rtd1195: Add UART resets
ARM: dts: rtd1195: Add reset nodes
dt-bindings: reset: Add Realtek RTD1195
ARM: dts: rtd1195: Add CRT syscon node
arm64: dts: realtek: rtd16xx: Introduce iso and misc syscon
arm64: dts: realtek: rtd139x: Introduce CRT, iso and misc syscon
arm64: dts: realtek: rtd129x: Introduce CRT, iso and misc syscon
ARM: dts: rtd1195: Introduce iso and misc syscon
arm64: dts: realtek: rtd1295: Add Xnano X5
dt-bindings: arm: realtek: Add Xnano X5
dt-bindings: vendor-prefixes: Add Xnano
arm64: dts: realtek: rtd16xx: Add memory reservations
arm64: dts: realtek: rtd16xx: Carve out boot ROM from memory
arm64: dts: realtek: Add RTD1619 SoC and Realtek Mjolnir EVB
...
Link: https://lore.kernel.org/r/20200510232158.18477-2-afaerber@suse.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed into arm/dt
ASPEED device tree updates for 5.8
New machines:
- YADRO's ast2500 OpenPower P9 Nicole BMC
- Facebook's ast2500 x86 Yosemite V2 BMC
The AST2600 machines Rainier and Tacoma were fleshed out.
Machines have started describing the GPIO names as userspace attempts
to use the GPIO chardev API.
* tag 'aspeed-5.8-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed: (32 commits)
ARM: dts: aspeed: Change KCS nodes to v2 binding
ARM: dts: Aspeed: AST2600: Add XDMA PCI-E root control reset
ARM: dts: aspeed: ast2600: Add XDMA Engine
ARM: dts: aspeed: ast2500: Add XDMA Engine
ARM: dts: aspeed: Adding Facebook Yosemite V2 BMC
ARM: dts: aspeed: Add YADRO Nicole BMC
ARM: dts: aspeed: mihawk: add aliases for i2c
ARM: dts: aspeed: tacoma: Add TPM
ARM: dts: aspeed: tacoma: Enable the second VUART
ARM: dts: aspeed: tacoma: Add iio-hwmon nodes for IIO devices
ARM: dts: aspeed: rainier: Add VGA reserved memory region
ARM: dts: aspeed: rainier: Add gpio line names
ARM: dts: aspeed: tacoma: Add gpio line names
ARM: dts: aspeed: zaius: Add gpio line names
ARM: dts: aspeed: romulus: Add gpio line names
ARM: dts: aspeed: witherspoon: Add gpio line names
ARM: dts: aspeed: ast2600: Set arch timer always-on
ARM: dts: aspeed: tacoma: Add GPIOs for FSI
ARM: dts: aspeed: mihawk: Change the name of leds
ARM: dts: aspeed: rainier: Remove regulators
...
Link: https://lore.kernel.org/r/CACPK8Xd-=XFREvvS-mK_ECyn14y0GPAMyy5BpEEUYfaw4jAgsw@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt
DTS changes for omaps for v5.8 merge window
We add support for beaglebone-ai board that's am5729 based devices.
Then we have a series changes to configure more hardware acceletators found
on omap variants. With the recent ti-sysc related changes, we can now better
configure the accelerators with help of the clock framework and reset driver.
So with a series of changes from Suman Anna and Tero Kristo, let's configure
IPUs and DSPs for dra7 devices like beagle-x15. And let's also configure the
missing crypto accelerators for omap5 as those have been missing.
Note that there are still some pending driver related patches to use IPU and
DSP related features with mainline kernel, but those are independent of the
devicetree changes.
Then there is a display related change for am57xx-idk for tc358778 bridge,
and a change to configure the missing clock source for some PWM timers.
* tag 'omap-for-v5.8/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (26 commits)
ARM: OMAP5: Make L4SEC clock domain SWSUP only
ARM: OMAP4: Make L4SEC clock domain SWSUP only
ARM: dts: omap5: add DES crypto accelerator node
ARM: dts: omap5: add SHA crypto accelerator node
ARM: dts: omap5: add aes2 entry
ARM: dts: omap5: add aes1 entry
ARM: dts: dra7-ipu-dsp-common: Add watchdog timers to IPU and DSP nodes
ARM: dts: am571x-idk: Add CMA pools and enable IPUs & DSP1 rprocs
ARM: dts: am572x-idk-common: Add CMA pools and enable IPU & DSP rprocs
ARM: dts: beagle-x15-common: Add CMA pools and enable IPU & DSP rprocs
ARM: dts: dra76-evm: Add CMA pools and enable IPU & DSP rprocs
ARM: dts: dra71-evm: Add CMA pools and enable IPUs & DSP1 rprocs
ARM: dts: dra72-evm-revc: Add CMA pools and enable IPUs & DSP1 rprocs
ARM: dts: dra72-evm: Add CMA pools and enable IPUs & DSP1 rprocs
ARM: dts: dra7-evm: Add CMA pools and enable IPU & DSP rprocs
ARM: dts: dra7-ipu-dsp-common: Add timers to IPU and DSP nodes
ARM: dts: dra7-ipu-dsp-common: Add mailboxes to IPU and DSP nodes
ARM: dts: dra7-ipu-dsp-common: Move mailboxes into common files
ARM: dts: DRA72x: Add aliases for rproc nodes
ARM: dts: DRA74x: Add aliases for rproc nodes
...
Link: https://lore.kernel.org/r/pull-1588873628-477615@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt
Renesas DT binding updates for v5.8
- Document System Controller (SYSC) and Reset (RST) support for
RZ/G1H.
* tag 'renesas-dt-bindings-for-v5.8-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
dt-bindings: reset: rcar-rst: Document r8a7742 reset module
dt-bindings: power: rcar-sysc: Document r8a7742 SYSC binding
Link: https://lore.kernel.org/r/20200430084849.1457-6-geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt
Renesas ARM DT updates for v5.8
- USB, UART, PWM, and PCIe support for R-Car M3-W+,
- PWM (16-bit Timer Pulse Unit and PWM Timers) support for R-Car M2-W,
- Minor fixes and cleanups.
* tag 'renesas-arm-dt-for-v5.8-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
arm64: dts: renesas: Fix IOMMU device node names
ARM: dts: renesas: Fix IOMMU device node names
ARM: dts: shmobile: Update CMT1 compatible values
ARM: dts: r8a7791: Add PWM device nodes
ARM: dts: r8a7791: Add TPU device node
arm64: dts: renesas: r8a77961: Add PCIe device nodes
arm64: dts: renesas: r8a77961: Add PWM device nodes
arm64: dts: renesas: r8a77961: Add SCIF and HSCIF nodes
arm64: dts: renesas: r8a77961: Add USB3.0 device nodes
arm64: dts: renesas: r8a77961: Add USB2.0 device nodes
Link: https://lore.kernel.org/r/20200430084849.1457-3-geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into arm/dt
Versatile DTS updates for the v5.8 kernel:
Create a new device tree for the Integrator/AP with the
IM-PD1 expansion module fitted in the first slot.
If we want to augment the slot where it is sitting, we can
alter the device tree or make the bootloader do so.
* tag 'versatile-dts-v5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: dts: Add devicetree for Integrator/AP with IM-PD1
Link: https://lore.kernel.org/r/CACRpkdZ-28o+pPdP7i_fc+7g4ndPWf+SWTsjnhFEegTggiXVSg@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti into arm/dt
STi DT fixes:
- Remove duplicated rng node in stih407-family.dtsi
- Fix complain about IRQ_TYPE_NONE usage in stih418.dtsi
* tag 'sti-dt-for-v5.8-round1' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti:
dts: arm: stih407-family: remove duplicated rng nodes
dts: arm: stih418: Fix complain about IRQ_TYPE_NONE usage
Link: https://lore.kernel.org/r/4b0c02e7-a247-50c0-d729-88d16b9dd7fd@st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add emmc and sd card devicetree nodes for SC9863A.
Link: https://lore.kernel.org/r/20200414101636.24503-3-zhang.lyra@gmail.com
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
add clock devicetree nodes for SC9863A.
Link: https://lore.kernel.org/r/20200414101636.24503-2-zhang.lyra@gmail.com
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Adds in CTI device tree information for the Hikey620 board.
Signed-off-by: Mike Leach <mike.leach@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
|
|
Only the pinmux was selected, not the pinconf, leading to spi issues.
Increase drive strength so that max speed (25Mhz) can be achieved.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
|
|
Commit c2ce5fb3f3f5 ('ARM: OMAP: DRA7xx: Make L4SEC clock domain SWSUP
only') made DRA7 SoC L4SEC clock domain SWSUP only because of power
state transition issues detected with HWSUP mode. Based on
experimentation similar issue exists on OMAP5, so do the same change
for OMAP5 also.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit c2ce5fb3f3f5 ('ARM: OMAP: DRA7xx: Make L4SEC clock domain SWSUP
only') made DRA7 SoC L4SEC clock domain SWSUP only because of power
state transition issues detected with HWSUP mode. Based on
experimentation similar issue exists on OMAP4, so do the same change
for OMAP4 also.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
OMAP5 contains a single DES crypto accelerator instance. Add node for
this in DT to enable it.
We keep the node disabled for now, as it appears OMAP5 platform is
running out of available DMA channels, and DES is the least interesting
crypto accelerator available on the device.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add the single available SHA crypto accelerator device for OMAP5 SoC.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
OMAP5 has AES hardware cryptographic accelerator, add AES2 instance for
it.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
OMAP5 has AES hardware cryptographic accelerator, add AES1 instance for
it.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The watchdog timer information has been added to all the IPU and DSP
remote processor device nodes in the DRA7xx/AM57xx SoC families. The
data has been added to the two common dra7-ipu-dsp-common and
dra74-ipu-dsp-common dtsi files that can be included by all the
desired board files. The following timers are chosen as the watchdog
timers, as per the usage on the current firmware images:
IPU2: GPTimers 4 & 9 (one for each Cortex-M4 core)
IPU1: GPTimers 7 & 8 (one for each Cortex-M4 core)
DSP1: GPTimer 10
DSP2: GPTimer 13
Each of the IPUs has two Cortex-M4 processors and so uses a timer
each for providing watchdog support on that processor irrespective of
whether the IPU is running in SMP-mode or non-SMP node. The chosen
timers also need to be unique from the ones used by other processors
(regular timers or watchdog timers) so that they can be supported
simultaneously.
The MPU-side drivers will use this data to initialize the watchdog
timer(s), and listen for any watchdog triggers. The BIOS-side code on
these processors needs to configure/refresh the corresponding timer
properly to not throw a watchdog error.
The watchdog timers are optional in general, but are mandatory to
be added to support watchdog error recovery on a particular processor.
These timers can be changed or removed as per the system integration
needs, alongside appropriate equivalent changes on the firmware side.
Signed-off-by: Angela Stegmaier <angelabaker@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The CMA reserved memory nodes have been added for both the IPUs and the
DSP1 remoteproc devices on the AM571x IDK board. These nodes are assigned
to the respective rproc device nodes, and both the IPUs and the DSP1
remote processors are enabled for this board.
The current CMA pools and sizes are defined statically for each device.
The addresses chosen are the same as the respective processors on the
DRA72 EVM board to maintain firmware compatibility between the two boards.
The CMA pools and sizes are defined using 64-bit values to support LPAE.
The starting addresses are fixed to meet current dependencies on the
remote processor firmwares, and this will go away when the remote-side
code has been improved to gather this information runtime during its
initialization.
An associated pair of the rproc node and its CMA node can be disabled
later on if there is no use-case defined to use that remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The CMA reserved memory nodes have been added for all the IPU and DSP
remoteproc devices in the am572x-idk-common.dtsi file that is common to
both the AM572x and AM574x IDK boards. These nodes are assigned to the
respective rproc device nodes, and all the IPU and DSP remote processors
are enabled.
The current CMA pools and sizes are defined statically for each device.
The addresses chosen are the same as the respective processors on
the AM57xx EVM board to maintain firmware compatibility between the
two boards. The CMA pools and sizes are defined using 64-bit values
to support LPAE. The starting addresses are fixed to meet current
dependencies on the remote processor firmwares, and this will go
away when the remote-side code has been improved to gather this
information runtime during its initialization.
An associated pair of the rproc node and its CMA node can be disabled
later on if there is no use-case defined to use that remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The CMA reserved memory nodes have been added for all the IPU and DSP
remoteproc devices on all the AM57xx BeagleBoard-X15 boards. These nodes
are assigned to the respective rproc device nodes, and all the IPU and
DSP remote processors are enabled for all these boards.
The current CMA pools and sizes are defined statically for each device.
The addresses chosen are the same as the respective processors on the
DRA7 EVM board to maintain firmware compatibility between the two boards.
The CMA pools and sizes are defined using 64-bit values to support LPAE.
The starting addresses are fixed to meet current dependencies on the
remote processor firmwares, and this will go away when the remote-side
code has been improved to gather this information runtime during its
initialization.
An associated pair of the rproc node and its CMA node can be disabled
later on if there is no use-case defined to use that remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The CMA reserved memory nodes have been added for all the IPU and
the DSP remoteproc devices on the DRA76 EVM board, and assigned to
the respective rproc device nodes. These match the configuration
used on the DRA7 EVM board. Both the CMA nodes and the corresponding
rproc nodes are also enabled to enable these processors on the
DRA76 EVM board.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The CMA reserved memory nodes have been added for both the IPUs and the
DSP1 remoteproc devices on DRA71 EVM board. These nodes are assigned to
the respective rproc device nodes, and both the IPUs and the DSP1 remote
processors are enabled for this board.
The current CMA pools and sizes are defined statically for each device.
The addresses chosen are the same as the respective processors on the
DRA72 EVM board to maintain firmware compatibility between the two boards.
The CMA pools and sizes are defined using 64-bit values to support LPAE.
The starting addresses are fixed to meet current dependencies on the
remote processor firmwares, and this will go away when the remote-side
code has been improved to gather this information runtime during its
initialization.
An associated pair of the rproc node and its CMA node can be disabled
later on if there is no use-case defined to use that remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The CMA reserved memory nodes have been added for both the IPUs and
the DSP1 remoteproc devices on the DRA72 EVM rev C board, and assigned
to the respective rproc device nodes. These match the configuration
used on the DRA72 EVM board. Both the CMA nodes and the corresponding
rproc nodes are also enabled to enable these processors on the
DRA72 EVM rev C board.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The CMA reserved memory nodes have been added for both the IPUs and the
DSP1 remoteproc devices on DRA72 EVM board. These nodes are assigned to
the respective rproc device nodes, and both the IPUs and the DSP1 remote
processors are enabled for this board.
The current CMA pools and sizes are defined statically for each device.
The addresses chosen are the same as the respective processors on the
DRA7 EVM board to maintain firmware compatibility between the two boards.
The CMA pools and sizes are defined using 64-bit values to support LPAE.
The starting addresses are fixed to meet current dependencies on the
remote processor firmwares, and this will go away when the remote-side
code has been improved to gather this information runtime during its
initialization.
An associated pair of the rproc node and its CMA node can be disabled
later on if there is no use-case defined to use that remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The CMA reserved memory nodes have been added for all the IPU and DSP
remoteproc devices on DRA7 EVM board. These nodes are assigned to the
respective rproc device nodes, and all the IPU and DSP remote processors
are enabled for this board.
The current CMA pools and sizes are defined statically for each device.
The CMA pools and sizes are defined using 64-bit values to support LPAE.
The starting addresses are fixed to meet current dependencies on the
remote processor firmwares, and this will go away when the remote-side
code has been improved to gather this information runtime during its
initialization.
An associated pair of the rproc node and its CMA node can be disabled
later on if there is no use-case defined to use that remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The BIOS System Tick timers have been added for all the IPU and
DSP remoteproc devices in the DRA7 SoC family. The data is added
to the two common dra7-ipu-dsp-common and dra74-ipu-dsp-common
dtsi files that are included by all the desired board files. The
following timers are chosen, as per the timers used on the current
firmware images:
IPU2: GPTimer 3
IPU1: GPTimer 11
DSP1: GPTimer 5
DSP2: GPTimer 6
The timers are optional, but are mandatory to support advanced device
management features such as power management and watchdog support.
The above are added to successfully boot and execute firmware images
configured with the respective timers, images that use internal
processor subsystem timers are not affected. The timers can be
changed or removed as per the system integration needs, if needed.
Each of the IPUs has two Cortex-M4 processors, and is currently
expected to be running in SMP-mode, so only a single timer suffices
to provide the BIOS tick timer. An additional timer should be added
for the second processor in IPU if it were to be run in non-SMP mode.
The timer value also needs to be unique from the ones used by other
processors so that they can be run simultaneously.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add the required 'mboxes' property to all the IPU and DSP remote
processors (IPU1, IPU2, DSP1 and DSP2) in the two available common
dtsi files - dra7-ipu-dsp-common and dra74-ipu-dsp-common dtsi files.
The latter file is for platforms having DRA74x/DRA76x/AM572x/AM574x
SoCs which do have a DSP2 processor in addition to the other common
remote processors. The common data is added to the former file, and
the DSP2 only data is added to the latter file.
The mailboxes are required for running the Remote Processor Messaging
(RPMsg) stack between the host processor and each of the remote
processors. Each of the remote processors uses a single sub-mailbox
node, the IPUs are assumed to be running in SMP-mode. The chosen
sub-mailboxes match the values used in the current firmware images.
This can be changed, if needed, as per the system integration needs
after making appropriate changes on the firmware side as well.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The System Mailboxes 5 and 6 and their corresponding child sub-mailbox
(IPC 3.x) nodes are enabled in each of the DRA7xx and AM57xx board
dts files individually at present. These mailboxes enable the Remote
Processor Messaging (RPMsg) communication stack between the MPU host
processor and each of the IPU1, IPU2, DSP1 and DSP2 remote processors.
Move these nodes into two common dtsi files - dra7-ipu-dsp-common and
dra74-ipu-dsp-common files, which are then included in various board
dts files. These files can be used to add all the common configuration
properties (except memory data) required by remote processor nodes.
The memory pools and the remote processor nodes themselves are to be
enabled in the actual board dts files. The first file is to used by
platforms using DRA72x/DRA71x/AM571x/AM570x SoCs, and the second file
is to be used by platforms using DRA74x/DRA76x/AM572x/AM574x SoCs.
The second file includes the first file and contains additional data
only applicable for DSP2 remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add aliases for all the 3 remote processor nodes common to
all DRA72x/DRA71x/AM571x/AM570x boards. The aliases uses the
stem "rproc", and are defined in the order of the most common
processors on the DRA72x family. The ids are same as DRA74x
except for the missing DSP2.
The aliases can be overridden, if needed, in the respective
derivative board dts files.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add aliases for all the IPU and DSP remoteproc processor
nodes common to all DRA74x/DRA76x/AM572x/AM574x boards.
The aliases uses the stem "rproc". The aliases are defined
in the order of the most common processors on the DRA74x
family.
The aliases can be overridden, if needed, in the respective
derivative board dts files.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The DRA7xx family of SoCs can contain upto two identical DSP
processor subsystems. The second DSP processor subsystem is
present only on the DRA74x/DRA76x variants. The processor
device DT node has therefore been added in disabled state for
this processor subsystem in the DRA74x specific DTS file.
NOTE:
1. The node does not have any mailboxes, timers or CMA region
assigned, they should be added in the respective board dts
files.
2. The node should also be enabled as per the individual product
configuration in the corresponding board dts files.
Signed-off-by: Suman Anna <s-anna@ti.com>
[t-kristo@ti.com: converted to support ti-sysc from legacy hwmod]
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The DRA7xx family of SOCs have two IPUs and upto two DSP
processor subsystems in general. The IPU processor subsystem
contains dual-core ARM Cortex-M4 processors, while the DSP
processor subsystem is based on the TI's standard TMS320C66x
DSP CorePac core. The IPUs are very similar to those on OMAP5.
Two IPUs and one DSP processor subsystems is the most common
configuration. The processor device DT nodes have been added
for these processor subsystems, with the internal memories
added through 'reg' and 'reg-names' properties. The IPUs only
have an L2 RAM, whereas the DSPs have L1P, L1D and L2 RAM
memories.
NOTE:
1. The nodes do not have any mailboxes, timers or CMA regions
assigned, they should be added in the respective board dts
files.
2. The nodes haven been disabled by default and the enabling
of these nodes is also left to the respective board dts
files.
Signed-off-by: Suman Anna <s-anna@ti.com>
[t-kristo@ti.com: convert to ti-sysc support from legacy hwmod]
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
With this, the clocksource driver can setup the timers properly.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
|
|
Clocksource to timer configured in pwm mode can be selected using the DT
property ti,clock-source. There are few pwm timers which are not
selecting the clock source and relying on default value in hardware or
selected by driver. Instead of relying on default value, always select
the clock source from DT.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Fixes the following warnings for both g5 and g6 SoCs:
arch/arm/boot/dts/aspeed-g5.dtsi:376.19-381.8: Warning
(unit_address_vs_reg): /ahb/apb/lpc@1e789000/lpc-bmc@0/kcs1@0: node
has a unit name, but no reg property
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
The AST2600 XDMA engine requires the PCI-E root control reset be cleared
as well, so add a phandle to that syscon reset.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Add a node for the XDMA engine with all the necessary information.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Add a node for the XDMA engine with all the necessary information.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
The Yosemite V2 is a facebook multi-node server
platform that host four OCP server. The BMC
in the Yosemite V2 platform based on AST2500 SoC.
This patch adds linux device tree entry related to
Yosemite V2 specific devices connected to BMC SoC.
Signed-off-by: Manikandan Elumalai <manikandan.hcl.ers.epl@gmail.com>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Vijay Khemka <vkhemka@fb.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Nicole is an OpenPower machine with an Aspeed 2500 BMC SoC manufactured
by YADRO.
Signed-off-by: Alexander Filippov <a.filippov@yadro.com>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Patrick Williams <patrick@stwcx.xyz>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Set the bus id for each mux channel to avoid switching channels
multiple times
Signed-off-by: Ben Pai <Ben_Pai@wistron.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Add the Nuvoton NPCT75X to the appropriate i2c bus.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Used by some POWER hypervisors.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Connect the BMP280 and DPS310 to the hwmon subsystem with iio-hwmon
nodes.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
The BMC uses reserves the top 16MB of memory for the host to use for VGA
or PCIe communication.
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|