| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Former comment looks to be one intended behavior in code,
actually it's not. So correct it.
Suggested-by: Christian König <[email protected]>
Signed-off-by: Guchun Chen <[email protected]>
Acked-by: Christian König <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
[WHY]
Programming DPPCLK to the same value currently set may cause
underflow while playing video in certain conditions.
[HOW]
Only program DPPCLK if clock is not the same as the
previous value programmed.
Signed-off-by: Sung Lee <[email protected]>
Reviewed-by: Yongqiang Sun <[email protected]>
Acked-by: Rodrigo Siqueira <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
[Why]
In DCN hardware sequencer we do actually call ATOM_INIT correctly per
pipe. The workaround is not necessary for command table offloading.
[How]
Drop the workaround since it's not needed.
Signed-off-by: Nicholas Kazlauskas <[email protected]>
Reviewed-by: Chris Park <[email protected]>
Acked-by: Rodrigo Siqueira <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
Fix warning during switching to dpg pause mode for
VCN firmware Version ENC: 1.1 DEC: 1 VEP: 0 Revision: 16
Signed-off-by: James Zhu <[email protected]>
Acked-by: Leo Liu <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
GDS clear workaround will cause gfx failure in suspend/resume case.
[ 98.679559] [drm:amdgpu_device_ip_late_init [amdgpu]] *ERROR* late_init of IP block <gfx_v9_0> failed -110
[ 98.679561] PM: dpm_run_callback(): pci_pm_resume+0x0/0xa0 returns -110
[ 98.679562] PM: Device 0000:03:00.0 failed to resume async: error -110
As this workaround is specific to the HW bug of GDS's ECC error
existing in cold boot up, so bypass this workaround in suspend/
resume case after booting up.
Signed-off-by: Guchun Chen <[email protected]>
Reviewed-by: Hawking Zhang <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
hwc->conf was designated specifically for AMD APU IOMMU purposes. This
could cause problems in performance and/or function since APU IOMMU
implementation is elsewhere. Also hwc->conf and hwc->config are
different members of an anonymous union so hwc->conf aliases as
hw->last_tag.
Signed-off-by: Jonathan Kim <[email protected]>
Reviewed-by: Felix Kuehling <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
On PowerPC, the compiler will tag object files with whether they
use hard or soft float FP ABI and whether they use 64 or 128-bit
long double ABI. On systems with 64-bit long double ABI, a tag
will get emitted whenever a double is used, as on those systems
a long double is the same as a double. This will prevent linkage
as other files are being compiled with hard-float.
On ppc64, this code will never actually get used for the time
being, as the only currently existing hardware using it are the
Renoir APUs. Therefore, until this is testable and can be fixed
properly, at least make sure the build will not fail.
Signed-off-by: Daniel Kolesa <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
Support pause_state for multiple instance, and it will fix vcn2.5 DPG mode
power off issue on instance 1.
Signed-off-by: James Zhu <[email protected]>
Reviewed-by: Leo Liu <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
[Why]
Starting from 14nm, the PLL is built into the PHY and the PLL is mapped
to PHY on 1 to 1 basis. In the code, the DP port is mapped to a PLL that was not
initialized. This causes DP to HDMI dongle to not light up the display.
[How]
Initializations added for PLL2 when creating resources.
Signed-off-by: Isabel Zhang <[email protected]>
Reviewed-by: Eric Yang <[email protected]>
Acked-by: Bhawanpreet Lakha <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
[Why]
Underflow is observed when plug in a 4K@60 monitor with
1366x768 eDP due to DPPCLK is too low.
[How]
Limit minimum DPPCLK to 100MHz.
Signed-off-by: Yongqiang Sun <[email protected]>
Reviewed-by: Eric Yang <[email protected]>
Acked-by: Bhawanpreet Lakha <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
[Why]
Engine can be NULL in some cases, so we must not acquire it.
[How]
Check for NULL engine before acquiring.
Signed-off-by: Aric Cyr <[email protected]>
Reviewed-by: Harry Wentland <[email protected]>
Acked-by: Bhawanpreet Lakha <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
The Audioengine D1 (0x2912:0x30c8) does support reading the sample rate,
but it returns the rate in byte-reversed order.
When setting sampling rate, the driver produces these warning messages:
[168840.944226] usb 3-2.2: current rate 4500480 is different from the runtime rate 44100
[168854.930414] usb 3-2.2: current rate 8436480 is different from the runtime rate 48000
[168905.185825] usb 3-2.1.2: current rate 30465 is different from the runtime rate 96000
As can be seen from the hexadecimal conversion, the current rate read
back is byte-reversed from the rate that was set.
44100 == 0x00ac44, 4500480 == 0x44ac00
48000 == 0x00bb80, 8436480 == 0x80bb00
96000 == 0x017700, 30465 == 0x007701
Rather than implementing a new quirk to reverse the order, just skip
checking the rate to avoid spamming the log.
Signed-off-by: Arvind Sankar <[email protected]>
Cc: <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
[WHY & HOW]
Previously drain clk was unconstrained and fill clk was constrained on fclk.
We want to change it to fill clk unconstrained and drain clock constrained
to dcfclk.
Signed-off-by: Sung Lee <[email protected]>
Reviewed-by: Tony Cheng <[email protected]>
Acked-by: Bhawanpreet Lakha <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
[WHY]
The optimized_require flag is needed to set watermarks and clocks lower
in certain conditions. This flag is set to true and then set to false
while programming front end in dcn20.
[HOW]
Do not set the flag to false while disabling plane.
Signed-off-by: Sung Lee <[email protected]>
Reviewed-by: Tony Cheng <[email protected]>
Acked-by: Bhawanpreet Lakha <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
[Why]
Driver crash with psr feature enabled due to divide-by-zero error.
This is a regression after rework to calculate static screen frame
number entry time.
[How]
Correct order of operations to avoid divide-by-zero.
Signed-off-by: Roman Li <[email protected]>
Reviewed-by: Zhan Liu <[email protected]>
Acked-by: Bhawanpreet Lakha <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
We've got a regression report about M-Audio Fast Track C400 device,
and the git bisection resulted in the commit e0ccdef92653 ("ALSA:
usb-audio: Clean up check_input_term()"). This commit was about the
rewrite of the input terminal parser, and it's not too obvious from
the change what really broke. The answer is: it's the interpretation
of UAC2/3 effect units.
In the original code, UAC2 effect unit is as if through UAC1
processing unit because both UAC1 PU and UAC2/3 EU share the same
number (0x07). The old code went through a complex switch-case
fallthrough, finally bailing out in the middle:
if (protocol == UAC_VERSION_2 &&
hdr[2] == UAC2_EFFECT_UNIT) {
/* UAC2/UAC1 unit IDs overlap here in an
* uncompatible way. Ignore this unit for now.
*/
return 0;
}
... and this special handling was missing in the new code; the new
code treats UAC2/3 effect unit as if it were equivalent with the
processing unit.
Actually, the old code was too confusing. The effect unit has an
incompatible unit description with the processing unit, so we
shouldn't have dealt with EU in the same way.
This patch addresses the regression by changing the effect unit
handling to the own parser function. The own parser function makes
the clear distinct with PU, so it improves the readability, too.
The EU parser just sets the type and the id like the old kernels.
Once when the proper effect unit support is added, we can revisit this
parser function, but for now, let's keep this simple setup as is.
Fixes: e0ccdef92653 ("ALSA: usb-audio: Clean up check_input_term()")
Cc: <[email protected]>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=206147
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
Jabra Evolve 65 headset appears as if supporting lower rates than
48kHz, but it actually doesn't work but with 48kHz for playback.
This patch applies a workaround to enforce the 48kHz like LINE6
devices already did. The workaround is put in a unified helper
function, set_fixed_rate(), to be called from both places now.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=206149
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
Only assert that the i915_vma is now idle if and only if no other pins
are present. If another user has the i915_vma pinned, they may submit
more work to the i915_vma skipping the vm->mutex used to serialise the
unbind. We need to wait again, if we want to continue and unbind this
vma.
However, if we own the i915_vma (we hold the vm->mutex for the unbind
and the pin_count is 0), we can assert that the vma remains idle as we
unbind.
Fixes: 2850748ef876 ("drm/i915: Pull i915_vma_pin under the vm->mutex")
Closes: https://gitlab.freedesktop.org/drm/intel/issues/530
Signed-off-by: Chris Wilson <[email protected]>
Cc: Tvrtko Ursulin <[email protected]>
Reviewed-by: Tvrtko Ursulin <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
(cherry picked from commit 60e94557fff1f5514c7fc4da7ddc2c7a13ffff26)
Signed-off-by: Jani Nikula <[email protected]>
|
|
To multiply 2 u32 numbers to generate a u64 in C requires a bit of
forewarning for the compiler.
Signed-off-by: Chris Wilson <[email protected]>
Cc: Ramalingam C <[email protected]>
Cc: Joonas Lahtinen <[email protected]>
Cc: [email protected]
Reviewed-by: Ville Syrjälä <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
(cherry picked from commit 0f8f8a64300092852b9361cd835395ee71e6a7d6)
Signed-off-by: Jani Nikula <[email protected]>
|
|
For a simulated preemption reset, we don't populate the request and so
do not fill in the guilty context name.
[ 79.991294] i915 0000:00:02.0: GPU HANG: ecode 9:1:e757fefe, in [0]
Just don't mention the empty string in the logs!
Fixes: 742379c0c400 ("drm/i915: Start chopping up the GPU error capture")
Signed-off-by: Chris Wilson <[email protected]>
Cc: Mika Kuoppala <[email protected]>
Reviewed-by: Mika Kuoppala <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
(cherry picked from commit 29baf3ae8daa4c673de58106ff41c7236dff57f4)
Signed-off-by: Jani Nikula <[email protected]>
|
|
Currently we create a new mmap_offset for every call to
mmap_offset_ioctl. This exposes ourselves to an abusive client that may
simply create new mmap_offsets ad infinitum, which will exhaust physical
memory and the virtual address space. In addition to the exhaustion, a
very long linear list of mmap_offsets causes other clients using the
object to incur long list walks -- these long lists can also be
generated by simply having many clients generate their own mmap_offset.
However, we can simply use the drm_vma_node itself to manage the file
association (allow/revoke) dropping our need to keep an mmo per-file.
Then if we keep a small rbtree of per-type mmap_offsets, we can lookup
duplicate requests quickly.
Fixes: cc662126b413 ("drm/i915: Introduce DRM_I915_GEM_MMAP_OFFSET")
Signed-off-by: Chris Wilson <[email protected]>
Cc: Abdiel Janulgue <[email protected]>
Reviewed-by: Abdiel Janulgue <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
(cherry picked from commit 7865559872074a9ab169c87915504661d630addf)
Signed-off-by: Jani Nikula <[email protected]>
|
|
We need to allow concurrent intel_context_unpin, which means avoiding
doing destructive operations like intel_ring_reset(). This was already
fixed for intel_ring_unpin() in commit 0725d9a31869 ("drm/i915/gt: Make
intel_ring_unpin() safe for concurrent pint"), but I overlooked that
execlists_context_unpin() also made the same mistake.
Reported-by: Matthew Brost <[email protected]>
Fixes: 841350223816 ("drm/i915/gt: Drop mutex serialisation between context pin/unpin")
References: 0725d9a31869 ("drm/i915/gt: Make intel_ring_unpin() safe for concurrent pint")
Signed-off-by: Chris Wilson <[email protected]>
Cc: Matthew Brost <[email protected]>
Cc: Matthew Auld <[email protected]>
Cc: Tvrtko Ursulin <[email protected]>
Reviewed-by: Mika Kuoppala <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
(cherry picked from commit f3c0efc9fe7a4e61544034f525348a3aa86ac5aa)
Signed-off-by: Jani Nikula <[email protected]>
|
|
The entire asm/archrandom.h header is generically included via
linux/archrandom.h only when CONFIG_ARCH_RANDOM is already set, so the
stub definitions of __arm64_rndr() and __early_cpu_has_rndr() are only
visible to KASLR if it explicitly includes the arch-internal header.
Acked-by: Mark Brown <[email protected]>
Signed-off-by: Robin Murphy <[email protected]>
Signed-off-by: Will Deacon <[email protected]>
|
|
It is theoretically possible for the ACPI EC GPE to be set after the
s2idle_ops->wake() called from s2idle_loop() has returned and before
the subsequent pm_wakeup_pending() check is carried out. If that
happens, the resulting wakeup event will cause the system to resume
even though it may be a spurious one.
To avoid that race, first make the ->wake() callback in struct
platform_s2idle_ops return a bool value indicating whether or not
to let the system resume and rearrange s2idle_loop() to use that
value instad of the direct pm_wakeup_pending() call if ->wake() is
present.
Next, rework acpi_s2idle_wake() to process EC events and check
pm_wakeup_pending() before re-arming the SCI for system wakeup
to prevent it from triggering prematurely and add comments to
that function to explain the rationale for the new code flow.
Fixes: 56b991849009 ("PM: sleep: Simplify suspend-to-idle control flow")
Cc: 5.4+ <[email protected]> # 5.4+
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
Commit 016b87ca5c8c ("ACPI: EC: Rework flushing of pending work")
introduced a subtle bug into the flushing of pending EC work while
suspended to idle, which may cause the EC driver to fail to
re-enable the EC GPE after handling a non-wakeup event (like a
battery status change event, for example).
The problem is that the work item flushed by flush_scheduled_work()
in __acpi_ec_flush_work() may disable the EC GPE and schedule another
work item expected to re-enable it, but that new work item is not
flushed, so __acpi_ec_flush_work() returns with the EC GPE disabled
and the CPU running it goes into an idle state subsequently. If all
of the other CPUs are in idle states at that point, the EC GPE won't
be re-enabled until at least one CPU is woken up by another interrupt
source, so system wakeup events that would normally come from the EC
then don't work.
This is reproducible on a Dell XPS13 9360 in my office which
sometimes stops reacting to power button and lid events (triggered
by the EC on that machine) after switching from AC power to battery
power or vice versa while suspended to idle (each of those switches
causes the EC GPE to trigger for several times in a row, but they
are not system wakeup events).
To avoid this problem, it is necessary to drain the workqueue
entirely in __acpi_ec_flush_work(), but that cannot be done with
respect to system_wq, because work items may be added to it from
other places while __acpi_ec_flush_work() is running. For this
reason, make the EC driver use a dedicated workqueue for EC events
processing (let that workqueue be ordered so that EC events are
processed sequentially) and use drain_workqueue() on it in
__acpi_ec_flush_work().
Fixes: 016b87ca5c8c ("ACPI: EC: Rework flushing of pending work")
Cc: 5.4+ <[email protected]> # 5.4+
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
Move the checking, buffer reserve and buffer commit code in
synth_event_trace_start/end() into inline functions
__synth_event_trace_start/end() so they can also be used by
synth_event_trace() and synth_event_trace_array(), and then have all
those functions use them.
Also, change synth_event_trace_state.enabled to disabled so it only
needs to be set if the event is disabled, which is not normally the
case.
Link: http://lkml.kernel.org/r/b1f3108d0f450e58192955a300e31d0405ab4149.1581374549.git.zanussi@kernel.org
Signed-off-by: Tom Zanussi <[email protected]>
Signed-off-by: Steven Rostedt (VMware) <[email protected]>
|
|
There's no reason to return -EINVAL when tracing a synthetic event if
it's soft disabled - treat it the same as if it were hard disabled and
return normally.
Have synth_event_trace() and synth_event_trace_array() just return
normally, and have synth_event_trace_start set the trace state to
disabled and return.
Link: http://lkml.kernel.org/r/df5d02a1625aff97c9866506c5bada6a069982ba.1581374549.git.zanussi@kernel.org
Fixes: 8dcc53ad956d2 ("tracing: Add synth_event_trace() and related functions")
Signed-off-by: Tom Zanussi <[email protected]>
Signed-off-by: Steven Rostedt (VMware) <[email protected]>
|
|
If the ring_buffer reserve in synth_event_trace_start() fails, the
matching ring_buffer_nest_end() should be called in the error code,
since nothing else will ever call it in this case.
Link: http://lkml.kernel.org/r/20abc444b3eeff76425f895815380abe7aa53ff8.1581374549.git.zanussi@kernel.org
Fixes: 8dcc53ad956d2 ("tracing: Add synth_event_trace() and related functions")
Signed-off-by: Tom Zanussi <[email protected]>
Signed-off-by: Steven Rostedt (VMware) <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fix from Tejun Heo:
"I made a mistake while removing cgroup task list lazy init
optimization making the root cgroup.procs show entries for the
init_tasks. The zero entries doesn't cause critical failures but does
make systemd print out warning messages during boot.
Fix it by omitting init_tasks as they should be"
* 'for-5.6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: init_tasks shouldn't be linked to the root cgroup
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux
Pull SELinux fixes from Paul Moore:
"Two small fixes: one fixes a locking problem in the recently merged
label translation code, the other fixes an embarrassing 'binderfs' /
'binder' filesystem name check"
* tag 'selinux-pr-20200210' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux:
selinux: fix sidtab string cache locking
selinux: fix typo in filesystem name
|
|
Suppress non-error messages when applying new bootconfig
to initrd image. To enable it, replace printf for error
message with pr_err() macro.
This also adds a testcase for this fix.
Link: http://lkml.kernel.org/r/158125351377.16911.13283712972275131160.stgit@devnote2
Reported-by: Michael Ellerman <[email protected]>
Tested-by: Michael Ellerman <[email protected]>
Signed-off-by: Masami Hiramatsu <[email protected]>
Signed-off-by: Steven Rostedt (VMware) <[email protected]>
|
|
To reduce the large static array from kernel data, allocate
xbc_nodes array dynamically only if the kernel loads a
bootconfig.
Note that this also add dummy memblock.h for user-spacae
bootconfig tool.
Link: http://lkml.kernel.org/r/158108569699.3187.6512834527603883707.stgit@devnote2
Signed-off-by: Masami Hiramatsu <[email protected]>
Signed-off-by: Steven Rostedt (VMware) <[email protected]>
|
|
Since commit 56d589361572 ("kbuild: do not create orphan built-in.a or
obj-y objects"), scripts/link-vmlinux.sh does nothing when descending
into init/.
Once the version number becomes out of sync between .version and
include/generated/compile.h, it is not self-healing.
[How to reproduce]
$ echo 100 > .version
$ make
You will see the number in the .version is always bigger than that in
compile.h by one. After this, every time you run 'make', the vmlinux is
re-linked even when none of source files is updated.
Fixes: 56d589361572 ("kbuild: do not create orphan built-in.a or obj-y objects")
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
memcpy() writes one more byte than allocated.
Fixes: 8d60526999aa ("scripts/kallsyms: change table to store (strcut sym_entry *)")
Reported-by: youling257 <[email protected]>
Reported-by: Pavel Machek <[email protected]>
Signed-off-by: Masahiro Yamada <[email protected]>
Tested-by: Pavel Machek <[email protected]>
|
|
Even though a SMMUv3 PMCG implementation may use an MSI as the form of
interrupt source, the kernel would still complain that it does not find
the wired (GSIV) interrupt in this case:
root@(none)$ dmesg | grep arm-smmu-v3-pmcg | grep "not found"
[ 59.237219] arm-smmu-v3-pmcg arm-smmu-v3-pmcg.8.auto: IRQ index 0 not found
[ 59.322841] arm-smmu-v3-pmcg arm-smmu-v3-pmcg.9.auto: IRQ index 0 not found
[ 59.422155] arm-smmu-v3-pmcg arm-smmu-v3-pmcg.10.auto: IRQ index 0 not found
[ 59.539014] arm-smmu-v3-pmcg arm-smmu-v3-pmcg.11.auto: IRQ index 0 not found
[ 59.640329] arm-smmu-v3-pmcg arm-smmu-v3-pmcg.12.auto: IRQ index 0 not found
[ 59.743112] arm-smmu-v3-pmcg arm-smmu-v3-pmcg.13.auto: IRQ index 0 not found
[ 59.880577] arm-smmu-v3-pmcg arm-smmu-v3-pmcg.14.auto: IRQ index 0 not found
[ 60.017528] arm-smmu-v3-pmcg arm-smmu-v3-pmcg.15.auto: IRQ index 0 not found
Use platform_get_irq_optional() to silence the warning.
If neither interrupt source is found, then the driver will still warn that
IRQ setup errored and the probe will fail.
Reviewed-by: Robin Murphy <[email protected]>
Signed-off-by: John Garry <[email protected]>
Signed-off-by: Will Deacon <[email protected]>
|
|
The current implementation does a naive search of "bootconfig" on the kernel
command line. But this could find "bootconfig" that is part of another
option in quotes (although highly unlikely). But it also needs to find '--'
on the kernel command line to know if it should append a '--' or not when a
bootconfig in the initrd file has an "init" section. The check uses the
naive strstr() to find to see if it exists. But this can return a false
positive if it exists in an option and then the "init" section in the initrd
will not be appended properly.
Using parse_args() to find both of these will solve both of these problems.
Link: https://lore.kernel.org/r/202002070954.C18E7F58B@keescook
Fixes: 7495e0926fdf3 ("bootconfig: Only load bootconfig if "bootconfig" is on the kernel cmdline")
Fixes: 1319916209ce8 ("bootconfig: init: Allow admin to use bootconfig for init command line")
Reported-by: Kees Cook <[email protected]>
Reviewed-by: Kees Cook <[email protected]>
Acked-by: Masami Hiramatsu <[email protected]>
Signed-off-by: Steven Rostedt (VMware) <[email protected]>
|
|
There is a potential execution path in which variable *ret* is returned
without being properly initialized, previously.
Fix this by initializing variable *ret* to 0.
Link: http://lkml.kernel.org/r/20200205223404.GA3379@embeddedor
Addresses-Coverity-ID: 1491142 ("Uninitialized scalar variable")
Fixes: 2a588dd1d5d6 ("tracing: Add kprobe event command generation functions")
Reviewed-by: Tom Zanussi <[email protected]>
Acked-by: Masami Hiramatsu <[email protected]>
Signed-off-by: Gustavo A. R. Silva <[email protected]>
Signed-off-by: Steven Rostedt (VMware) <[email protected]>
|
|
Since there is no user except CONFIG_BOOT_CONFIG and no plan
to use it from other functions, CONFIG_LIBXBC can be removed
and we can use CONFIG_BOOT_CONFIG directly.
Link: http://lkml.kernel.org/r/158098769281.939.16293492056419481105.stgit@devnote2
Suggested-by: Geert Uytterhoeven <[email protected]>
Signed-off-by: Masami Hiramatsu <[email protected]>
Signed-off-by: Steven Rostedt (VMware) <[email protected]>
|
|
Since printk() wrapper macro uses __VA_ARGS__ without "##" prefix, it causes
a build error if there is no variable arguments (e.g. only fmt is
specified.) To fix this error, use ##__VA_ARGS__ instead of __VAR_ARGS__.
Link: http://lkml.kernel.org/r/158108370130.2758.10893830923800978011.stgit@devnote2
Fixes: 950313ebf79c ("tools: bootconfig: Add bootconfig command")
Reported-by: Michael Ellerman <[email protected]>
Tested-by: Michael Ellerman <[email protected]>
Signed-off-by: Masami Hiramatsu <[email protected]>
Signed-off-by: Steven Rostedt (VMware) <[email protected]>
|
|
We have been using the fact that the QMI and DIAG functions
usually are the only ones with class/subclass/protocol being
ff/ff/ff on Quectel modems. This has allowed us to match the
QMI function without knowing the exact interface number,
which can vary depending on firmware configuration.
The ability to silently reject the DIAG function, which is
usually handled by the option driver, is important for this
method to work. This is done based on the knowledge that it
has exactly 2 bulk endpoints. QMI function control interfaces
will have either 3 or 1 endpoint. This rule is universal so
the quirk condition can be removed.
The fixed layouts known from the Gobi1k and Gobi2k modems
have been gradually replaced by more dynamic layouts, and
many vendors now use configurable layouts without changing
device IDs. Renaming the class/subclass/protocol matching
macro makes it more obvious that this is now not Quectel
specific anymore.
Cc: Kristian Evensen <[email protected]>
Cc: Aleksander Morgado <[email protected]>
Signed-off-by: Bjørn Mork <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
When adding support for unique interrupt names, after testing on a few
devices, it was assumed 32 characters would be sufficient. This
assumption turned out to be incorrect, ZII RDU2 for example uses a
device base name of mv88e6xxx-30be0000.ethernet-1:0, leaving no space
for post fixes such as -g1-atu-prob and -watchdog. The names then
become identical, defeating the point of the patch.
Increase the length of the string to 64 charactoes.
Reported-by: Chris Healy <[email protected]>
Fixes: 3095383a8ab4 ("net: dsa: mv88e6xxx: Unique IRQ name")
Signed-off-by: Andrew Lunn <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Commit f25e1392fdb5 removed the support for the pre-production variant
of the Dell DW5821e to avoid probing another USB interface unnecessarily.
However, the pre-production samples are found in the wild, and this lack
of support is causing problems for users of such samples. It is therefore
necessary to support both variants.
Matching on both interfaces 0 and 1 is not expected to cause any problem
with either variant, as only the QMI function will be probed successfully
on either. Interface 1 will be rejected based on the HID class for the
production variant:
T: Bus=01 Lev=03 Prnt=04 Port=00 Cnt=01 Dev#= 16 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 2
P: Vendor=413c ProdID=81d7 Rev=03.18
S: Manufacturer=DELL
S: Product=DW5821e Snapdragon X20 LTE
S: SerialNumber=0123456789ABCDEF
C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I: If#= 1 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=00 Prot=00 Driver=usbhid
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
And interface 0 will be rejected based on too few endpoints for the
pre-production variant:
T: Bus=01 Lev=02 Prnt=02 Port=03 Cnt=03 Dev#= 7 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 2
P: Vendor=413c ProdID=81d7 Rev= 3.18
S: Manufacturer=DELL
S: Product=DW5821e Snapdragon X20 LTE
S: SerialNumber=0123456789ABCDEF
C: #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
Fixes: f25e1392fdb5 ("qmi_wwan: fix interface number for DW5821e production firmware")
Link: https://whrl.pl/Rf0vNk
Reported-by: Lars Melin <[email protected]>
Cc: Aleksander Morgado <[email protected]>
Signed-off-by: Bjørn Mork <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Typcasting "irq_state" leads to the below static checker warning:
The fix is to declare "irq_state" as unsigned long instead of u32.
drivers/gpio/gpio-sifive.c:97 sifive_gpio_irq_enable()
warn: passing casted pointer '&chip->irq_state' to
'assign_bit()' 32 vs 64.
Fixes: 96868dce644d ("gpio/sifive: Add GPIO driver for SiFive SoCs")
Reported-by: Dan Carpenter <[email protected]>
Signed-off-by: Yash Shah <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Marc Zyngier <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
In converting over to using set_bit()/test_bit(), when manually
inspecting the rq->fence.flags, we need to use BIT().
Fixes: e1c31fb5dde3 ("drm/i915: Merge i915_request.flags with i915_request.fence.flags")
Signed-off-by: Chris Wilson <[email protected]>
Cc: Tvrtko Ursulin <[email protected]>
Cc: Matthew Auld <[email protected]>
Reviewed-by: Tvrtko Ursulin <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
(cherry picked from commit 72ff2b8d5f2dcb09bfa37b902c23311eec426496)
Signed-off-by: Jani Nikula <[email protected]>
|
|
Add a i915_vma to the mock_engine/mock_ring so that the core code can
always assume the presence of ring->vma.
Fixes: 8ccfc20a7d56 ("drm/i915/gt: Mark ring->vma as active while pinned")
Signed-off-by: Chris Wilson <[email protected]>
Reviewed-by: Mika Kuoppala <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
(cherry picked from commit b63b4feaef7363d2cf46dd76bb6e87e060b2b0de)
Signed-off-by: Jani Nikula <[email protected]>
|
|
intel_prepare_plane_fb() will always pin plane_state->hw.fb whenever
it is present. We copy that from the master plane to the slave plane,
but we fail to copy the corresponding ggtt view. Thus when it comes time
to pin the slave plane's fb we use some stale ggtt view left over from
the last time the plane was used as a non-slave plane. If that previous
use involved 90/270 degree rotation or remapping we'll try to shuffle
the pages of the new fb around accordingingly. However the new
fb may be backed by a bo with less pages than what the ggtt view
rotation/remapped info requires, and so we we trip a GEM_BUG().
Steps to reproduce on icl:
1. plane 1: whatever
plane 6: largish !NV12 fb + 90 degree rotation
2. plane 1: smallish NV12 fb
plane 6: make invisible so it gets slaved to plane 1
3. GEM_BUG()
Cc: Chris Wilson <[email protected]>
Cc: Maarten Lankhorst <[email protected]>
Closes: https://gitlab.freedesktop.org/drm/intel/issues/951
Fixes: 1f594b209fe1 ("drm/i915: Remove special case slave handling during hw programming, v3.")
Signed-off-by: Ville Syrjälä <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Reviewed-by: Chris Wilson <[email protected]>
(cherry picked from commit 103605e0d1e77cfb5d0f5a9e8aba7d97f1b49339)
Signed-off-by: Jani Nikula <[email protected]>
|
|
Take and hold a reference to each of the vma (and their objects) as we
process them with the cmdparser. This stops them being freed during the
work if the GEM execbuf is interrupted and the request we expected to
keep the objects alive is incomplete.
Fixes: 686c7c35abc2 ("drm/i915/gem: Asynchronous cmdparser")
Closes: https://gitlab.freedesktop.org/drm/intel/issues/970
Signed-off-by: Chris Wilson <[email protected]>
Cc: Joonas Lahtinen <[email protected]>
Reviewed-by: Mika Kuoppala <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
(cherry picked from commit 36c8e356a76e147f0b631fd29838147c01b50d04)
Signed-off-by: Jani Nikula <[email protected]>
|
|
The rc6 residency starts ticking from 0 from BIOS POST, but the kernel
starts measuring the time from its boot. If we start measuruing
I915_PMU_RC6_RESIDENCY while the GT is idle, we start our sampling from
0 and then upon first activity (park/unpark) add in all the rc6
residency since boot. After the first park with the sampler engaged, the
sleep/active counters are aligned.
v2: With a wakeref to be sure
Closes: https://gitlab.freedesktop.org/drm/intel/issues/973
Fixes: df6a42053513 ("drm/i915/pmu: Ensure monotonic rc6")
Signed-off-by: Chris Wilson <[email protected]>
Cc: Tvrtko Ursulin <[email protected]>
Reviewed-by: Tvrtko Ursulin <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
(cherry picked from commit f4e9894b6952a2819937f363cd42e7cd7894a1e4)
Signed-off-by: Jani Nikula <[email protected]>
|
|
I see the following lockdep splat in the qcom pinctrl driver when
attempting to suspend the device.
WARNING: possible recursive locking detected
5.4.11 #3 Tainted: G W
--------------------------------------------
cat/3074 is trying to acquire lock:
ffffff81f49804c0 (&irq_desc_lock_class){-.-.}, at: __irq_get_desc_lock+0x64/0x94
but task is already holding lock:
ffffff81f1cc10c0 (&irq_desc_lock_class){-.-.}, at: __irq_get_desc_lock+0x64/0x94
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&irq_desc_lock_class);
lock(&irq_desc_lock_class);
*** DEADLOCK ***
May be due to missing lock nesting notation
6 locks held by cat/3074:
#0: ffffff81f01d9420 (sb_writers#7){.+.+}, at: vfs_write+0xd0/0x1a4
#1: ffffff81bd7d2080 (&of->mutex){+.+.}, at: kernfs_fop_write+0x12c/0x1fc
#2: ffffff81f4c322f0 (kn->count#337){.+.+}, at: kernfs_fop_write+0x134/0x1fc
#3: ffffffe411a41d60 (system_transition_mutex){+.+.}, at: pm_suspend+0x108/0x348
#4: ffffff81f1c5e970 (&dev->mutex){....}, at: __device_suspend+0x168/0x41c
#5: ffffff81f1cc10c0 (&irq_desc_lock_class){-.-.}, at: __irq_get_desc_lock+0x64/0x94
stack backtrace:
CPU: 5 PID: 3074 Comm: cat Tainted: G W 5.4.11 #3
Hardware name: Google Cheza (rev3+) (DT)
Call trace:
dump_backtrace+0x0/0x174
show_stack+0x20/0x2c
dump_stack+0xc8/0x124
__lock_acquire+0x460/0x2388
lock_acquire+0x1cc/0x210
_raw_spin_lock_irqsave+0x64/0x80
__irq_get_desc_lock+0x64/0x94
irq_set_irq_wake+0x40/0x144
qpnpint_irq_set_wake+0x28/0x34
set_irq_wake_real+0x40/0x5c
irq_set_irq_wake+0x70/0x144
pm8941_pwrkey_suspend+0x34/0x44
platform_pm_suspend+0x34/0x60
dpm_run_callback+0x64/0xcc
__device_suspend+0x310/0x41c
dpm_suspend+0xf8/0x298
dpm_suspend_start+0x84/0xb4
suspend_devices_and_enter+0xbc/0x620
pm_suspend+0x210/0x348
state_store+0xb0/0x108
kobj_attr_store+0x14/0x24
sysfs_kf_write+0x4c/0x64
kernfs_fop_write+0x15c/0x1fc
__vfs_write+0x54/0x18c
vfs_write+0xe4/0x1a4
ksys_write+0x7c/0xe4
__arm64_sys_write+0x20/0x2c
el0_svc_common+0xa8/0x160
el0_svc_handler+0x7c/0x98
el0_svc+0x8/0xc
Set a lockdep class when we map the irq so that irq_set_wake() doesn't
warn about a lockdep bug that doesn't exist.
Fixes: 12a9eeaebba3 ("spmi: pmic-arb: convert to v2 irq interfaces to support hierarchical IRQ chips")
Cc: Douglas Anderson <[email protected]>
Cc: Brian Masney <[email protected]>
Cc: Lina Iyer <[email protected]>
Cc: Maulik Shah <[email protected]>
Cc: Bjorn Andersson <[email protected]>
Signed-off-by: Stephen Boyd <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Linus Walleij <[email protected]>
|
|
Care is taken with "index", however with the current version
the actual xgpio_writereg is using index for data but
xgpio_regoffset(chip, i) for the offset. And since i is already
incremented it is incorrect. This patch fixes it so that index
is used for the offset too.
Cc: [email protected]
Signed-off-by: Paul Thomas <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Linus Walleij <[email protected]>
|