| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
dcdc3 supplies to DDR on AM43x series. When we set both
min and max values to the same value. The regulator framework
sets that particular voltage. This is bad as we are changing
the ddr voltage when executing from ddr. Hence remove the min and
max values. The ddr supply voltage shall be set from bootloader
when not executing from ddr and not while executing from kernel.
The previous discussion can be found here:
http://www.spinics.net/lists/devicetree/msg56399.html
Signed-off-by: Keerthy <[email protected]>
Signed-off-by: Tony Lindgren <[email protected]>
|
|
BeagleBone Blue is robotics-oriented version of the BeagleBone Black (BBB).
This board can be indentified by the BLAx value after A335BNLT (BBB)
in the at24 eeprom:
BLAx [aa 55 33 ee 41 33 33 35 42 4e 4c 54 42 4c 41 30 |.U3.A335BNLTBLA2|]
http://beagleboard.org/blue
https://github.com/beagleboard/beaglebone-blue
firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware
wl18xx mac address: /proc/device-tree/ocp/ethernet@4a100000/slave@4a100200/mac-address
Signed-off-by: Robert Nelson <[email protected]>
CC: Jason Kridner <[email protected]>
CC: Drew Fustini <[email protected]>
Acked-by: Jason Kridner <[email protected]>
Signed-off-by: Tony Lindgren <[email protected]>
|
|
The twl4030_charger driver expects an iio channel to detect the
presence of an AC charger by looking at VAC (madc channel 11).
This definition is missing in the device tree.
Signed-off-by: Marek Belisko <[email protected]>
Signed-off-by: Sebastian Reichel <[email protected]>
Signed-off-by: Tony Lindgren <[email protected]>
|
|
This defines the memory location and interrupt used by the GSBI8
I2C adapter on the MSM8660 SoCs. We add it as "disabled" by
default so that boards using this I2C can enable it.
Signed-off-by: Linus Walleij <[email protected]>
Acked-by: Bjorn Andersson <[email protected]>
Signed-off-by: Andy Gross <[email protected]>
|
|
This adds the Capella CM3605 ambient light and proximity sensor
to the APQ8060 DragonBoard device tree. Notice that we also set
up pin config for the AOUT line and GPIO lines, and that we set
the default trigger on the infrared LED to associate with the
"cm3605" trigger so the IR LED is controlled by this the CM3605
driver.
Signed-off-by: Linus Walleij <[email protected]>
Acked-by: Bjorn Andersson <[email protected]>
Signed-off-by: Andy Gross <[email protected]>
|
|
This adds the PM8058 XOADC node to the PM8058 PMIC node,
defines the 16 channels and further also define an IIO HWMON
node for the channels that are used for housekeeping of
voltages and die temperature for the PMIC chip die.
Tested on the APQ8060 DragonBoard:
cd /sys/class/hwmon/hwmon0
cat in2_input
4773 (DC mains ~5V)
cat in4_input
625 (0.625V reference voltage)
cat in5_input
1250 (1.25V reference voltage)
cat temp1_input
35852 (die temperature)
Signed-off-by: Linus Walleij <[email protected]>
Acked-by: Bjorn Andersson <[email protected]>
Signed-off-by: Andy Gross <[email protected]>
|
|
This patch fixes two typos in the i2c_0 node for the ipq4019.
The reg property length is just 0x600. The core clock is
GCC_BLSP1_QUP1_I2C_APPS_CLK. GCC_BLSP1_QUP2_I2C_APPS_CLK is
used by the second i2c.
Fixes: e76b4284b520ba3 ("qcom: ipq4019: add i2c node to ipq4019 SoC and DK01 device tree")
Signed-off-by: Christian Lamparter <[email protected]>
Signed-off-by: Andy Gross <[email protected]>
|
|
The gsbi_serial7 under gsbi7 is used by the IPQ8068 based board EWS870AP as
main serial console.
Signed-off-by: Sven Eckelmann <[email protected]>
Signed-off-by: Andy Gross <[email protected]>
|
|
Follow the recent trend for the license description, and fix the wrongly
stated X11 to MIT.
The X11 license text [1] is explicitly for the X Consortium and has a
couple of extra clauses. The MIT license text [2] is actually what the
current DT files claim.
[1] https://spdx.org/licenses/X11.html
[2] https://spdx.org/licenses/MIT.html
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Compiling the UniPhier DT files with W=1, DTC warns like follows:
Warning (simple_bus_reg): Node /soc/system-bus@58c00000/support_card@1,1f00000/ethernet@00000000 simple-bus unit address format error, expected "0"
Warning (simple_bus_reg): Node /soc/system-bus@58c00000/support_card@1,1f00000/uart@000b0000 simple-bus unit address format error, expected "b0000"
Warning (simple_bus_reg): Node /soc/smpctrl@59800000 simple-bus unit address format error, expected "59801000"
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Compiling the DT file with W=1, DTC warns like follows:
Warning (unit_address_vs_reg): Node /opp_table0/opp@1000000000 has a
unit name, but no reg property
Fix this by replacing '@' with '-' as the OPP nodes will never have a
"reg" property.
Reported-by: Krzysztof Kozlowski <[email protected]>
Reported-by: Masahiro Yamada <[email protected]>
Suggested-by: Mark Rutland <[email protected]>
Signed-off-by: Viresh Kumar <[email protected]>
Acked-by: Rob Herring <[email protected]>
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Add the remaining bit locations for the module stop clock registers.
Signed-off-by: Chris Brandt <[email protected]>
Reviewed-by: Geert Uytterhoeven <[email protected]>
Signed-off-by: Simon Horman <[email protected]>
|
|
The A83T's PRCM has the same set of clocks and resets as the A64.
However, a few dividers are different. And due to the lack of a low
speed 32.768 kHz oscillator, a few of the clock parents are different.
The PRCM also has controls for various power domains. These are not
supported yet, neither in software nor in the device tree binding.
Signed-off-by: Chen-Yu Tsai <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
|
|
Exynos5250 and Exynos542x SoCs have the same CEC hardware module as
Exynos4 SoC series, so enable support for it using the same compatible
string.
Tested on Odroid XU3 (Exynos5422) and Google Snow (Exynos5250) boards.
Signed-off-by: Marek Szyprowski <[email protected]>
Signed-off-by: Krzysztof Kozlowski <[email protected]>
|
|
Rockchip's rk3229 evaluation board has one usb otg controller
and three usb host controllers. Each usb controller connect
with one usb2 phy port through UTMI+ interface. And the three
usb host interfaces use the same GPIO VBUS drive. Let's enable
them to support usb on rk3229 evb board.
Signed-off-by: William Wu <[email protected]>
Signed-off-by: Heiko Stuebner <[email protected]>
|
|
This patch adds usb otg/host controllers and phys nodes on rk322x.
Signed-off-by: William Wu <[email protected]>
Signed-off-by: Heiko Stuebner <[email protected]>
|
|
This augments the Moxa Art and Aspeed device trees to:
- Explicitly name the clock "PCLK" as the Faraday FTTMR010
names it.
- List the Moxa timer as compatible with the Faradat FTTMR010
vanilla version.
- Add a comment that the Aspeed driver is a Faraday
FTTMR010 derivative.
- Pass all IRQs to the timer from Aspeed: they are all there
so they should be in the device tree, we only use the
first one anyways.
Tested-by: Joel Stanley <[email protected]>
Tested-by: Jonas Jensen <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
Signed-off-by: Olof Johansson <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into next/dt
This is a first set of Gemini DTS patches for the v4.13 cycle.
This adds the reset and clock lines to the Gemini core DTS SoC.
These bindings have been ACKed by the DT maintainer Rob.
The reset driver is going to be merged by the reset maintainer.
The clock driver is going to be merged by the clock maintainers.
Each of these have their macro defines coming with them, split
off as separate patches.
A post-rc1 patch will be sumbitted for switching the numerical
values to the defined macros in line with the ARM SoC DT header
merge strategy.
* tag 'gemini-v4.13-dts-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: Add clocks to the Gemini SoC
ARM: dts: Add the Gemini reset controller
dt-bindings: Augment Gemini for clocks, resets
Signed-off-by: Olof Johansson <[email protected]>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Renesas ARM Based SoC DT Updates for v4.13
* Switch to panel-lvds bindings for Mitsubishi panels
* Clean up PFC node names
* Enable UHS-I SDR-50 and SDR-104 on r8a7793/Gose
* Add GyroADC clock and device for r8a7791 SoC
* Add USB clocks to device tree for r7s72100 SoC
* tag 'renesas-dt-for-v4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: dts: renesas: Switch to panel-lvds bindings for Mitsubishi panels
ARM: dts: gose: Enable UHS-I SDR-50 and SDR-104
ARM: dts: r8a7793: set maximum frequency for SDHI clocks
ARM: dts: r8a7791: Add GyroADC clock and device node
ARM: dts: r7s72100: add usb clocks to device tree
ARM: dts: sh73a0: update PFC node name to pin-controller
ARM: dts: r8a7793: update PFC node name to pin-controller
ARM: dts: r8a7791: update PFC node name to pin-controller
ARM: dts: r8a7790: update PFC node name to pin-controller
ARM: dts: r8a7779: update PFC node name to pin-controller
ARM: dts: r8a7778: update PFC node name to pin-controller
ARM: dts: r8a7740: update PFC node name to pin-controller
ARM: dts: r8a73a4: update PFC node name to pin-controller
ARM: dts: emev2: update PFC node name to pin-controller
ARM: dts: r7s72100: add USB bit definitions
ARM: dts: r7s72100: add Renesas RZ/A1 pinctrl header
ARM: dts: r8a7791: add GyroADC clock
Signed-off-by: Olof Johansson <[email protected]>
|
|
The only adc button connected to adc input is recovery button.
Signed-off-by: Randy Li <[email protected]>
Signed-off-by: Heiko Stuebner <[email protected]>
|
|
NanoPi M1 Plus is designed and developed by FriendlyElec
for professionals, enterprise users, makers and hobbyists
using the Allwinner H3 SOC.
NanoPi M1 Plus key features
- Allwinner H3, Quad-core [email protected]
- 1GB DDR3 RAM
- 8GB eMMC
- microSD slot
- 10/100/1000M Ethernet
- Serial Debug Port
- 5V 2A DC power-supply
Signed-off-by: Jagan Teki <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
|
|
Add the needed clock nodes for the CLKOUT2 to be usable by boards.
Signed-off-by: Peter Ujfalusi <[email protected]>
Acked-by: Tero Kristo <[email protected]>
Signed-off-by: Tony Lindgren <[email protected]>
|
|
Add MT2701 i2c device node.
Signed-off-by: Jun Gao <[email protected]>
Signed-off-by: Matthias Brugger <[email protected]>
|
|
Signed-off-by: Rick Chang <[email protected]>
Signed-off-by: Minghsiu Tsai <[email protected]>
[mb: include mt2701-larb-port.h to fix build errors]
Signed-off-by: Matthias Brugger <[email protected]>
|
|
Add pwm controller bindings for sama5d2_xplained
and enable it.
Signed-off-by: Claudiu Beznea <[email protected]>
Signed-off-by: Alexandre Belloni <[email protected]>
|
|
sama5d3 CPU modules embed a parallel NOR flash connected to the EBI bus.
Signed-off-by: Boris Brezillon <[email protected]>
Signed-off-by: Alexandre Belloni <[email protected]>
|
|
Use the new EBI/NAND bindings to declare NAND chips and remove old NAND
nodes along the way.
Note that we keep using old bindings in at91rm9200.dtsi because this
SoC is not supported by the EBI driver.
Signed-off-by: Boris Brezillon <[email protected]>
Tested-by: Peter Rosin <[email protected]>
Signed-off-by: Alexandre Belloni <[email protected]>
|
|
Declare new nodes for the EBI and NAND controllers embedded in various
at91/sama5 SoCs.
Signed-off-by: Boris Brezillon <[email protected]>
Signed-off-by: Alexandre Belloni <[email protected]>
|
|
SAMA5 SoCs embed an advanced NAND controller logic to automate READ/WRITE
page accesses. This advanced logic is exposed through a separate I/O mem
range and is thus represented in a different node with its own compatible.
Document the bindings of this nfc-io block.
Signed-off-by: Boris Brezillon <[email protected]>
Signed-off-by: Alexandre Belloni <[email protected]>
|
|
According to the binding documentation and the source code the atmel-gpio
controller takes IRQ_TYPE_* as its flags values, not GPIO_ACTIVE_*.
This patch uses the right variable type which yields the same result
when compiled. Note that this might be wrong and actually
IRQ_TYPE_LEVEL_LOW is intended by the dt author.
Signed-off-by: Uwe Kleine-König <[email protected]>
Acked-by: Marek Vasut <[email protected]>
Signed-off-by: Alexandre Belloni <[email protected]>
|
|
The second cell in a gpio reference is used to pass GPIO_ACTIVE_LOW or
GPIO_ACTIVE_HIGH. The gpio device can also be used as irq controller and
a reference can contain the IRQ_TYPE_* values in the second cell.
Signed-off-by: Uwe Kleine-König <[email protected]>
Signed-off-by: Alexandre Belloni <[email protected]>
|
|
The gpio node has 144 gpios. Each gpio is capable of generating
an interrupt. Hence add interrupt-controller property to the gpio
node. With this in place one can use interrupts property in device
tree to request for the gpio interrupts.
Signed-off-by: Keerthy <[email protected]>
Signed-off-by: Sekhar Nori <[email protected]>
|
|
This adds CPPI 4.1 DMA controller to USB OTG controller.
Changes since v2:
- Fixed the the property reg-names (had glue register defined)
- Removed few useless property
Signed-off-by: Alexandre Bailon <[email protected]>
Signed-off-by: Sekhar Nori <[email protected]>
|
|
Add node for SPI NOR flash on orange-pi-zero board. Disable this node
by default and leave it to users to enable it if their board has
SPI NOR flash chip populated.
SPI NOR flash was optional in the first production batch in Dec 2016.
In later batches flash chip was pre-populated. However there should
be quite a few boards around which do not have flash chip.
Signed-off-by: Sergey Matyukevich <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
|
|
The USB PHY can use either a GPIO pin or the PMIC's USB power supply
to sense VBUS. Since both options are available on the Cubietruck,
add the missing property for the USB power supply to the USB PHY node.
The device tree provides all usable options. Ultimately, which method
is used is up to the driver implementation.
Signed-off-by: Chen-Yu Tsai <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
|
|
The ACIN pins of the AXP221 PMIC on the A31 Hummingbird are tied to the
DC jack on the board through a 12V to 5V buck converter.
Enable the ACIN power supply.
Signed-off-by: Chen-Yu Tsai <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
|
|
The ACIN pins of the AXP209 PMIC on the Cubieboard are tied to the
DC jack on the board.
Enable the ACIN power supply.
Signed-off-by: Chen-Yu Tsai <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
|
|
The ACIN pins of the AXP209 PMIC on the Bananapi M1 Plus are tied to the
"power input" micro USB connector next to the SATA connector on the board.
Enable the ACIN power supply.
Signed-off-by: Chen-Yu Tsai <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
|
|
The ACIN pins of the AXP209 PMIC on the Cubieboard 2 are tied to the
DC jack on the board.
Enable the ACIN power supply.
Signed-off-by: Chen-Yu Tsai <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
|
|
We want to keep node references in alphabetical order, except for
instances where node must be #included first.
Move the usb_otg node reference so that all references to non-AXP209
device nodes are in alphabetical order.
Signed-off-by: Chen-Yu Tsai <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal
Pull thermal SoC management fixes from Eduardo Valentin:
- fixes to TI SoC driver, Broadcom, qoriq
- small sparse warning fix on thermal core
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
thermal: broadcom: ns-thermal: default on iProc SoCs
ti-soc-thermal: Fix a typo in a comment line
ti-soc-thermal: Delete error messages for failed memory allocations in ti_bandgap_build()
ti-soc-thermal: Use devm_kcalloc() in ti_bandgap_build()
thermal: core: make thermal_emergency_poweroff static
thermal: qoriq: remove useless call for of_thermal_get_trip_points()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some serial and tty fixes for 4.12-rc3. They are a bit bigger
than normal, which is why I had them bake in linux-next for a few
weeks and didn't send them to you for -rc2.
They revert a few of the serdev patches from 4.12-rc1, and bring
things back to how they were in 4.11, to try to make things a bit more
stable there. Rob and Johan both agree that this is the way forward,
so this isn't people squabbling over semantics. Other than that, just
a few minor serial driver fixes that people have had problems with.
All of these have been in linux-next for a few weeks with no reported
issues"
* tag 'tty-4.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: altera_uart: call iounmap() at driver remove
serial: imx: ensure UCR3 and UFCR are setup correctly
MAINTAINERS/serial: Change maintainer of jsm driver
serial: enable serdev support
tty/serdev: add serdev registration interface
serdev: Restore serdev_device_write_buf for atomic context
serial: core: fix crash in uart_suspend_port
tty: fix port buffer locking
tty: ehv_bytechan: clean up init error handling
serial: ifx6x60: fix use-after-free on module unload
serial: altera_jtaguart: adding iounmap()
serial: exar: Fix stuck MSIs
serial: efm32: Fix parity management in 'efm32_uart_console_get_options()'
serdev: fix tty-port client deregistration
Revert "tty_port: register tty ports with serdev bus"
drivers/tty: 8250: only call fintek_8250_probe when doing port I/O
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Fix running SPU programs on Cell, and a few other minor fixes.
Thanks to Alistair Popple, Jeremy Kerr, Michael Neuling, Nicholas
Piggin"
* tag 'powerpc-4.12-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc: Add PPC_FEATURE userspace bits for SCV and DARN instructions
powerpc/spufs: Fix hash faults for kernel regions
powerpc: Fix booting P9 hash with CONFIG_PPC_RADIX_MMU=N
powerpc/powernv/npu-dma.c: Fix opal_npu_destroy_context() call
selftests/powerpc: Fix TM resched DSCR test with some compilers
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A series of fixes for X86:
- The final fix for the end-of-stack issue in the unwinder
- Handle non PAT systems gracefully
- Prevent access to uninitiliazed memory
- Move early delay calaibration after basic init
- Fix Kconfig help text
- Fix a cross compile issue
- Unbreak older make versions"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/timers: Move simple_udelay_calibration past init_hypervisor_platform
x86/alternatives: Prevent uninitialized stack byte read in apply_alternatives()
x86/PAT: Fix Xorg regression on CPUs that don't support PAT
x86/watchdog: Fix Kconfig help text file path reference to lockup watchdog documentation
x86/build: Permit building with old make versions
x86/unwind: Add end-of-stack check for ftrace handlers
Revert "x86/entry: Fix the end of the stack for newly forked tasks"
x86/boot: Use CROSS_COMPILE prefix for readelf
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixlet from Thomas Gleixner:
"Silence dmesg spam by making the posix cpu timer printks depend on
print_fatal_signals"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
posix-timers: Make signal printks conditional
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull RAS fixes from Thomas Gleixner:
"Two fixlets for RAS:
- Export memory_error() so the NFIT module can utilize it
- Handle memory errors in NFIT correctly"
* 'ras-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
acpi, nfit: Fix the memory error check in nfit_handle_mce()
x86/MCE: Export memory_error()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf tooling fixes from Thomas Gleixner:
- Synchronization of tools and kernel headers
- A series of fixes for perf report addressing various failures:
* Handle invalid maps proper
* Plug a memory leak
* Handle frames and callchain order correctly
- Fixes for handling inlines and children mode
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tools/include: Sync kernel ABI headers with tooling headers
perf tools: Put caller above callee in --children mode
perf report: Do not drop last inlined frame
perf report: Always honor callchain order for inlined nodes
perf script: Add --inline option for debugging
perf report: Fix off-by-one for non-activation frames
perf report: Fix memory leak in addr2line when called by addr2inlines
perf report: Don't crash on invalid maps in `-g srcline` mode
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fix from Thomas Gleixner:
"A fix for a state leak which was introduced in the recent rework of
futex/rtmutex interaction"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
futex,rt_mutex: Fix rt_mutex_cleanup_proxy_lock()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull kthread fix from Thomas Gleixner:
"A single fix which prevents a use after free when kthread fork fails"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
kthread: Fix use-after-free if kthread fork fails
|