aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2020-06-24net: ethernet: mvneta: Add back interface mode validationSascha Hauer1-3/+19
When writing the serdes configuration register was moved to mvneta_config_interface() the whole code block was removed from mvneta_port_power_up() in the assumption that its only purpose was to write the serdes configuration register. As mentioned by Russell King its purpose was also to check for valid interface modes early so that later in the driver we do not have to care for unexpected interface modes. Add back the test to let the driver bail out early on unhandled interface modes. Fixes: b4748553f53f ("net: ethernet: mvneta: Fix Serdes configuration for SoCs without comphy") Signed-off-by: Sascha Hauer <[email protected]> Reviewed-by: Russell King <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-06-24net: ethernet: mvneta: Do not error out in non serdes modesSascha Hauer1-1/+1
In mvneta_config_interface() the RGMII modes are catched by the default case which is an error return. The RGMII modes are valid modes for the driver, so instead of returning an error add a break statement to return successfully. This avoids this warning for non comphy SoCs which use RGMII, like SolidRun Clearfog: WARNING: CPU: 0 PID: 268 at drivers/net/ethernet/marvell/mvneta.c:3512 mvneta_start_dev+0x220/0x23c Fixes: b4748553f53f ("net: ethernet: mvneta: Fix Serdes configuration for SoCs without comphy") Signed-off-by: Sascha Hauer <[email protected]> Reviewed-by: Russell King <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-06-24dsa: Allow forwarding of redirected IGMP trafficDaniel Mack1-3/+34
The driver for Marvell switches puts all ports in IGMP snooping mode which results in all IGMP/MLD frames that ingress on the ports to be forwarded to the CPU only. The bridge code in the kernel can then interpret these frames and act upon them, for instance by updating the mdb in the switch to reflect multicast memberships of stations connected to the ports. However, the IGMP/MLD frames must then also be forwarded to other ports of the bridge so external IGMP queriers can track membership reports, and external multicast clients can receive query reports from foreign IGMP queriers. Currently, this is impossible as the EDSA tagger sets offload_fwd_mark on the skb when it unwraps the tagged frames, and that will make the switchdev layer prevent the skb from egressing on any other port of the same switch. To fix that, look at the To_CPU code in the DSA header and make forwarding of the frame possible for trapped IGMP packets. Introduce some #defines for the frame types to make the code a bit more comprehensive. This was tested on a Marvell 88E6352 variant. Signed-off-by: Daniel Mack <[email protected]> Reviewed-by: Andrew Lunn <[email protected]> Tested-by: Andrew Lunn <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-06-24openvswitch: take into account de-fragmentation/gso_size in ↵Lorenzo Bianconi1-2/+7
execute_check_pkt_len ovs connection tracking module performs de-fragmentation on incoming fragmented traffic. Take info account if traffic has been de-fragmented in execute_check_pkt_len action otherwise we will perform the wrong nested action considering the original packet size. This issue typically occurs if ovs-vswitchd adds a rule in the pipeline that requires connection tracking (e.g. OVN stateful ACLs) before execute_check_pkt_len action. Moreover take into account GSO fragment size for GSO packet in execute_check_pkt_len routine Fixes: 4d5ec89fc8d14 ("net: openvswitch: Add a new action check_pkt_len") Signed-off-by: Lorenzo Bianconi <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-06-24Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhostLinus Torvalds9-35/+207
Pull virtio fixes from Michael Tsirkin: "Fixes all over the place. This includes a couple of tests that I would normally defer, but since they have already been helpful in catching some bugs, don't build for any users at all, and having them upstream makes life easier for everyone, I think it's ok even at this late stage" * tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: tools/virtio: Use tools/include/list.h instead of stubs tools/virtio: Reset index in virtio_test --reset. tools/virtio: Extract virtqueue initialization in vq_reset tools/virtio: Use __vring_new_virtqueue in virtio_test.c tools/virtio: Add --reset tools/virtio: Add --batch=random option tools/virtio: Add --batch option virtio-mem: add memory via add_memory_driver_managed() virtio-mem: silence a static checker warning vhost_vdpa: Fix potential underflow in vhost_vdpa_mmap() vdpa: fix typos in the comments for __vdpa_alloc_device()
2020-06-24Merge tag 'for-linus-2020-06-24' of ↵Linus Torvalds4-6/+18
git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux Pull thread fix from Christian Brauner: "This fixes a regression introduced with 303cc571d107 ("nsproxy: attach to namespaces via pidfds"). The LTP testsuite reported a regression where users would now see EBADF returned instead of EINVAL when an fd was passed that referred to an open file but the file was not a namespace file. Fix this by continuing to report EINVAL and add a regression test" * tag 'for-linus-2020-06-24' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux: tests: test for setns() EINVAL regression nsproxy: restore EINVAL for non-namespace file descriptor
2020-06-24IB/hfi1: Add atomic triggered sleep/wakeupMike Marciniszyn2-20/+53
When running iperf in a two host configuration the following trace can occur: [ 319.728730] NETDEV WATCHDOG: ib0 (hfi1): transmit queue 0 timed out The issue happens because the current implementation relies on the netif txq being stopped to control the flushing of the tx list. There are two resources that the transmit logic can wait on and stop the txq: - SDMA descriptors - Ring space to hold completions The ring space is tested on the sending side and relieved when the ring is consumed in the napi tx reaping. Unfortunately, that reaping can run conncurrently with the workqueue flushing of the txlist. If the txq is started just before the workitem executes, the txlist will never be flushed, leading to the txq being stuck. Fix by: - Adding sleep/wakeup wrappers * Use an atomic to control the call to the netif routines inside the wrappers - Use another atomic to record ring space exhaustion * Only wakeup when the a ring space exhaustion has happened and it relieved Add additional wrappers to clarify the ring space resource handling. Fixes: d99dc602e2a5 ("IB/hfi1: Add functions to transmit datagram ipoib packets") Link: https://lore.kernel.org/r/[email protected] Reviewed-by: Kaike Wan <[email protected]> Signed-off-by: Mike Marciniszyn <[email protected]> Signed-off-by: Dennis Dalessandro <[email protected]> Signed-off-by: Jason Gunthorpe <[email protected]>
2020-06-24IB/hfi1: Correct -EBUSY handling in tx codeMike Marciniszyn1-17/+18
The current code mishandles -EBUSY in two ways: - The flow change doesn't test the return from the flush and runs on to process the current packet racing with the wakeup processing - The -EBUSY handling for a single packet inserts the tx into the txlist after the submit call, racing with the same wakeup processing Fix the first by dropping the skb and returning NETDEV_TX_OK. Fix the second by insuring the the list entry within the txreq is inited when allocated. This enables the sleep routine to detect that the txreq has used the non-list api and queue the packet to the txlist. Both flaws can lead to having the flushing thread executing in causing two threads to manipulate the txlist. Fixes: d99dc602e2a5 ("IB/hfi1: Add functions to transmit datagram ipoib packets") Link: https://lore.kernel.org/r/[email protected] Reviewed-by: Kaike Wan <[email protected]> Signed-off-by: Mike Marciniszyn <[email protected]> Signed-off-by: Dennis Dalessandro <[email protected]> Signed-off-by: Jason Gunthorpe <[email protected]>
2020-06-24IB/hfi1: Fix module use count flaw due to leftover module put callsDennis Dalessandro1-17/+2
When the try_module_get calls were removed from opening and closing of the i2c debugfs file, the corresponding module_put calls were missed. This results in an inaccurate module use count that requires a power cycle to fix. Fixes: 09fbca8e6240 ("IB/hfi1: No need to use try_module_get for debugfs") Link: https://lore.kernel.org/r/[email protected] Cc: <[email protected]> Reviewed-by: Kaike Wan <[email protected]> Reviewed-by: Mike Marciniszyn <[email protected]> Signed-off-by: Dennis Dalessandro <[email protected]> Signed-off-by: Jason Gunthorpe <[email protected]>
2020-06-24IB/hfi1: Restore kfree in dummy_netdev cleanupDennis Dalessandro1-1/+1
We need to do some rework on the dummy netdev. Calling the free_netdev() would normally make sense, and that will be addressed in an upcoming patch. For now just revert the behavior to what it was before keeping the unused variable removal part of the patch. The dd->dumm_netdev is mainly used for packet receiving through alloc_netdev_mqs() for typical net devices. A a result, it should be freed with kfree instead of free_netdev() that leads to a crash when unloading the hfi1 module: BUG: kernel NULL pointer dereference, address: 0000000000000000 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 8000000855b54067 P4D 8000000855b54067 PUD 84a4f5067 PMD 0 Oops: 0000 [#1] SMP PTI CPU: 73 PID: 10299 Comm: modprobe Not tainted 5.6.0-rc5+ #1 Hardware name: Intel Corporation S2600WT2R/S2600WT2R, BIOS SE5C610.86B.01.01.0016.033120161139 03/31/2016 RIP: 0010:__hw_addr_flush+0x12/0x80 Code: 40 00 48 83 c4 08 4c 89 e7 5b 5d 41 5c e9 76 77 18 00 66 0f 1f 44 00 00 0f 1f 44 00 00 41 54 49 89 fc 55 53 48 8b 1f 48 39 df <48> 8b 2b 75 08 eb 4a 48 89 eb 48 89 c5 48 89 df e8 99 bf d0 ff 84 RSP: 0018:ffffb40e08783db8 EFLAGS: 00010282 RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000002 RDX: ffffb40e00000000 RSI: 0000000000000246 RDI: ffff88ab13662298 RBP: ffff88ab13662000 R08: 0000000000001549 R09: 0000000000001549 R10: 0000000000000001 R11: 0000000000aaaaaa R12: ffff88ab13662298 R13: ffff88ab1b259e20 R14: ffff88ab1b259e42 R15: 0000000000000000 FS: 00007fb39b534740(0000) GS:ffff88b31f940000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000000 CR3: 000000084d3ea004 CR4: 00000000003606e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: dev_addr_flush+0x15/0x30 free_netdev+0x7e/0x130 hfi1_netdev_free+0x59/0x70 [hfi1] remove_one+0x65/0x110 [hfi1] pci_device_remove+0x3b/0xc0 device_release_driver_internal+0xec/0x1b0 driver_detach+0x46/0x90 bus_remove_driver+0x58/0xd0 pci_unregister_driver+0x26/0xa0 hfi1_mod_cleanup+0xc/0xd54 [hfi1] __x64_sys_delete_module+0x16c/0x260 ? exit_to_usermode_loop+0xa4/0xc0 do_syscall_64+0x5b/0x200 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Fixes: 193ba03141bb ("IB/hfi1: Use free_netdev() in hfi1_netdev_free()") Link: https://lore.kernel.org/r/[email protected] Reviewed-by: Mike Marciniszyn <[email protected]> Signed-off-by: Kaike Wan <[email protected]> Signed-off-by: Dennis Dalessandro <[email protected]> Signed-off-by: Jason Gunthorpe <[email protected]>
2020-06-24ALSA: usb-audio: Fix OOB access of mixer element listTakashi Iwai3-7/+20
The USB-audio mixer code holds a linked list of usb_mixer_elem_list, and several operations are performed for each mixer element. A few of them (snd_usb_mixer_notify_id() and snd_usb_mixer_interrupt_v2()) assume each mixer element being a usb_mixer_elem_info object that is a subclass of usb_mixer_elem_list, cast via container_of() and access it members. This may result in an out-of-bound access when a non-standard list element has been added, as spotted by syzkaller recently. This patch adds a new field, is_std_info, in usb_mixer_elem_list to indicate that the element is the usb_mixer_elem_info type or not, and skip the access to such an element if needed. Reported-by: [email protected] Reported-by: [email protected] Cc: <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Takashi Iwai <[email protected]>
2020-06-23Merge branch 'Two-phylink-pause-fixes'David S. Miller1-13/+32
Russell King says: ==================== Two phylink pause fixes While testing, I discovered two issues with ethtool -A with phylink. First, if there is a PHY bound to the network device, we hit a deadlock when phylib tries to notify us of the link changing as a result of triggering a renegotiation. Second, when we are manually forcing the pause settings, and there is no renegotiation triggered, we do not update the MAC via the new mac_link_up approach. These two patches solve both problems, and will need to be backported to v5.7; they do not apply cleanly there due to the introduction of PCS in the v5.8 merge window. ==================== Signed-off-by: David S. Miller <[email protected]>
2020-06-23net: phylink: ensure manual pause mode configuration takes effectRussell King1-5/+22
We have been relying on link events and mac_config() when the manual pause modes are changed. With recent developments, such as moving the programming of link state to mac_link_up(), this no longer works. To ensure that we update the MAC, we must generate a link-down followed by a link-up event; we can do that by setting mac_link_dropped and triggering a resolve. Fixes: 91a208f2185a ("net: phylink: propagate resolved link config via mac_link_up()") Signed-off-by: Russell King <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-06-23net: phylink: fix ethtool -A with attached PHYsRussell King1-9/+11
Fix a phylink's ethtool set_pauseparam support deadlock caused by phylib interacting with phylink: we must not hold the state lock while calling phylib functions that may call into phylink_phy_change(). Fixes: f904f15ea9b5 ("net: phylink: allow ethtool -A to change flow control advertisement") Signed-off-by: Russell King <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-06-23net: Do not clear the sock TX queue in sk_set_socket()Tariq Toukan2-1/+2
Clearing the sock TX queue in sk_set_socket() might cause unexpected out-of-order transmit when called from sock_orphan(), as outstanding packets can pick a different TX queue and bypass the ones already queued. This is undesired in general. More specifically, it breaks the in-order scheduling property guarantee for device-offloaded TLS sockets. Remove the call to sk_tx_queue_clear() in sk_set_socket(), and add it explicitly only where needed. Fixes: e022f0b4a03f ("net: Introduce sk_tx_queue_mapping") Signed-off-by: Tariq Toukan <[email protected]> Reviewed-by: Boris Pismenny <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-06-23net: ethtool: Handle missing cable test TDR parametersAndrew Lunn1-8/+9
A last minute change put the TDR cable test parameters into a nest. The validation is not sufficient, resulting in an oops if the nest is missing. Set default values first, then update them if the nest is provided. Fixes: f2bc8ad31a7f ("net: ethtool: Allow PHY cable test TDR data to configured") Signed-off-by: Andrew Lunn <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-06-23Merge branch 'bnxt_en-Bug-fixes'David S. Miller2-7/+34
Michael Chan says: ==================== bnxt_en: Bug fixes. The first patch stores the firmware version code which is needed by the next 2 patches to determine some worarounds based on the firmware version. The workarounds are to disable legacy TX push mode and to clear the hardware statistics during ifdown. The last patch checks that it is a PF before reading the VPD. Please also queue these for -stable. Thanks. ==================== Reviewed-by: Jakub Kicinski <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-06-23bnxt_en: Read VPD info only for PFsVasundhara Volam1-1/+2
Virtual functions does not have VPD information. This patch modifies calling bnxt_read_vpd_info() only for PFs and avoids an unnecessary error log. Fixes: a0d0fd70fed5 ("bnxt_en: Read partno and serialno of the board from VPD") Signed-off-by: Vasundhara Volam <[email protected]> Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-06-23bnxt_en: Fix statistics counters issue during ifdown with older firmware.Michael Chan1-1/+7
On older firmware, the hardware statistics are not cleared when the driver frees the hardware stats contexts during ifdown. The driver expects these stats to be cleared and saves a copy before freeing the stats contexts. During the next ifup, the driver will likely allocate the same hardware stats contexts and this will cause a big increase in the counters as the old counters are added back to the saved counters. We fix it by making an additional firmware call to clear the counters before freeing the hw stats contexts when the firmware is the older 20.x firmware. Fixes: b8875ca356f1 ("bnxt_en: Save ring statistics before reset.") Reported-by: Jakub Kicinski <[email protected]> Reviewed-by: Vasundhara Volam <[email protected]> Signed-off-by: Michael Chan <[email protected]> Tested-by: Jakub Kicinski <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-06-23bnxt_en: Do not enable legacy TX push on older firmware.Michael Chan2-1/+3
Older firmware may not support legacy TX push properly and may not be disabling it. So we check certain firmware versions that may have this problem and disable legacy TX push unconditionally. Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.") Reviewed-by: Edwin Peer <[email protected]> Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-06-23bnxt_en: Store the running firmware version code.Michael Chan2-4/+22
We currently only store the firmware version as a string for ethtool and devlink info. Store it also as a version code. The next 2 patches will need to check the firmware major version to determine some workarounds. We also use the 16-bit firmware version fields if the firmware is newer and provides the 16-bit fields. Reviewed-by: Edwin Peer <[email protected]> Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-06-23tracing/boottime: Fix kprobe multiple eventsSascha Ortmann1-2/+6
Fix boottime kprobe events to report and abort after each failure when adding probes. As an example, when we try to set multiprobe kprobe events in bootconfig like this: ftrace.event.kprobes.vfsevents { probes = "vfs_read $arg1 $arg2,, !error! not reported;?", // leads to error "vfs_write $arg1 $arg2" } This will not work as expected. After commit da0f1f4167e3af69e ("tracing/boottime: Fix kprobe event API usage"), the function trace_boot_add_kprobe_event will not produce any error message when adding a probe fails at kprobe_event_gen_cmd_start. Furthermore, we continue to add probes when kprobe_event_gen_cmd_end fails (and kprobe_event_gen_cmd_start did not fail). In this case the function even returns successfully when the last call to kprobe_event_gen_cmd_end is successful. The behaviour of reporting and aborting after failures is not consistent. The function trace_boot_add_kprobe_event now reports each failure and stops adding probes immediately. Link: https://lkml.kernel.org/r/[email protected] Cc: [email protected] Cc: [email protected] Co-developed-by: Maximilian Werner <[email protected]> Fixes: da0f1f4167e3 ("tracing/boottime: Fix kprobe event API usage") Acked-by: Masami Hiramatsu <[email protected]> Signed-off-by: Maximilian Werner <[email protected]> Signed-off-by: Sascha Ortmann <[email protected]> Signed-off-by: Steven Rostedt (VMware) <[email protected]>
2020-06-23tracing: Fix event trigger to accept redundant spacesMasami Hiramatsu1-2/+19
Fix the event trigger to accept redundant spaces in the trigger input. For example, these return -EINVAL echo " traceon" > events/ftrace/print/trigger echo "traceon if common_pid == 0" > events/ftrace/print/trigger echo "disable_event:kmem:kmalloc " > events/ftrace/print/trigger But these are hard to find what is wrong. To fix this issue, use skip_spaces() to remove spaces in front of actual tokens, and set NULL if there is no token. Link: http://lkml.kernel.org/r/159262476352.185015.5261566783045364186.stgit@devnote2 Cc: Tom Zanussi <[email protected]> Cc: [email protected] Fixes: 85f2b08268c0 ("tracing: Add basic event trigger framework") Reviewed-by: Tom Zanussi <[email protected]> Signed-off-by: Masami Hiramatsu <[email protected]> Signed-off-by: Steven Rostedt (VMware) <[email protected]>
2020-06-23tracing/boot: Fix config dependency for synthedic eventMasami Hiramatsu1-1/+1
Since commit 726721a51838 ("tracing: Move synthetic events to a separate file") decoupled synthetic event from histogram, boot-time tracing also has to check CONFIG_SYNTH_EVENT instead of CONFIG_HIST_TRIGGERS. Link: http://lkml.kernel.org/r/159262475441.185015.5300725180746017555.stgit@devnote2 Fixes: 726721a51838 ("tracing: Move synthetic events to a separate file") Reviewed-by: Tom Zanussi <[email protected]> Signed-off-by: Masami Hiramatsu <[email protected]> Signed-off-by: Steven Rostedt (VMware) <[email protected]>
2020-06-24erofs: fix partially uninitialized misuse in z_erofs_onlinepage_fixupGao Xiang1-10/+10
Hongyu reported "id != index" in z_erofs_onlinepage_fixup() with specific aarch64 environment easily, which wasn't shown before. After digging into that, I found that high 32 bits of page->private was set to 0xaaaaaaaa rather than 0 (due to z_erofs_onlinepage_init behavior with specific compiler options). Actually we only use low 32 bits to keep the page information since page->private is only 4 bytes on most 32-bit platforms. However z_erofs_onlinepage_fixup() uses the upper 32 bits by mistake. Let's fix it now. Reported-and-tested-by: Hongyu Jin <[email protected]> Fixes: 3883a79abd02 ("staging: erofs: introduce VLE decompression support") Cc: <[email protected]> # 4.19+ Reviewed-by: Chao Yu <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Gao Xiang <[email protected]>
2020-06-23bpf: Fix formatting in documentation for BPF helpersQuentin Monnet2-40/+42
When producing the bpf-helpers.7 man page from the documentation from the BPF user space header file, rst2man complains: <stdin>:2636: (ERROR/3) Unexpected indentation. <stdin>:2640: (WARNING/2) Block quote ends without a blank line; unexpected unindent. Let's fix formatting for the relevant chunk (item list in bpf_ringbuf_query()'s description), and for a couple other functions. Signed-off-by: Quentin Monnet <[email protected]> Signed-off-by: Alexei Starovoitov <[email protected]> Acked-by: Andrii Nakryiko <[email protected]> Link: https://lore.kernel.org/bpf/[email protected]
2020-06-23bpf: Restore behaviour of CAP_SYS_ADMIN allowing the loading of networking ↵Maciej Żenczykowski1-1/+1
bpf programs This is a fix for a regression in commit 2c78ee898d8f ("bpf: Implement CAP_BPF"). Before the above commit it was possible to load network bpf programs with just the CAP_SYS_ADMIN privilege. The Android bpfloader happens to run in such a configuration (it has SYS_ADMIN but not NET_ADMIN) and creates maps and loads bpf programs for later use by Android's netd (which has NET_ADMIN but not SYS_ADMIN). Fixes: 2c78ee898d8f ("bpf: Implement CAP_BPF") Reported-by: John Stultz <[email protected]> Signed-off-by: Maciej Żenczykowski <[email protected]> Signed-off-by: Alexei Starovoitov <[email protected]> Tested-by: John Stultz <[email protected]> Link: https://lore.kernel.org/bpf/[email protected]
2020-06-23bpf: Set the number of exception entries properly for subprogramsYonghong Song1-1/+9
Currently, if a bpf program has more than one subprograms, each program will be jitted separately. For programs with bpf-to-bpf calls the prog->aux->num_exentries is not setup properly. For example, with bpf_iter_netlink.c modified to force one function to be not inlined and with CONFIG_BPF_JIT_ALWAYS_ON the following error is seen: $ ./test_progs -n 3/3 ... libbpf: failed to load program 'iter/netlink' libbpf: failed to load object 'bpf_iter_netlink' libbpf: failed to load BPF skeleton 'bpf_iter_netlink': -4007 test_netlink:FAIL:bpf_iter_netlink__open_and_load skeleton open_and_load failed #3/3 netlink:FAIL The dmesg shows the following errors: ex gen bug which is triggered by the following code in arch/x86/net/bpf_jit_comp.c: if (excnt >= bpf_prog->aux->num_exentries) { pr_err("ex gen bug\n"); return -EFAULT; } This patch fixes the issue by computing proper num_exentries for each subprogram before calling JIT. Signed-off-by: Yonghong Song <[email protected]> Signed-off-by: Alexei Starovoitov <[email protected]>
2020-06-23libbpf: Fix CO-RE relocs against .text sectionAndrii Nakryiko2-2/+8
bpf_object__find_program_by_title(), used by CO-RE relocation code, doesn't return .text "BPF program", if it is a function storage for sub-programs. Because of that, any CO-RE relocation in helper non-inlined functions will fail. Fix this by searching for .text-corresponding BPF program manually. Adjust one of bpf_iter selftest to exhibit this pattern. Fixes: ddc7c3042614 ("libbpf: implement BPF CO-RE offset relocation algorithm") Reported-by: Yonghong Song <[email protected]> Signed-off-by: Andrii Nakryiko <[email protected]> Signed-off-by: Yonghong Song <[email protected]> Signed-off-by: Alexei Starovoitov <[email protected]> Acked-by: Yonghong Song <[email protected]> Link: https://lore.kernel.org/bpf/[email protected]
2020-06-23Merge branch 'cxgb4-cxgb4vf-fix-warnings-reported-by-sparse'David S. Miller18-169/+211
Rahul Lakkireddy says: ==================== cxgb4/cxgb4vf: fix warnings reported by sparse This series of patches fix various warnings reported by the sparse tool. Patches 1 and 2 fix lock context imbalance warnings. Patch 3 fixes cast to restricted __be64 warning when fetching timestamp in PTP path. Patch 4 fixes several cast to restricted __be32 warnings in TC-U32 offload parser. Patch 5 fixes several cast from restricted __be16 warnings in parsing L4 ports for filters. Patch 6 fixes several restricted __be32 degrades to integer warnings when comparing IP address masks for exact-match filters. Patch 7 fixes cast to restricted __be64 warning when fetching SGE queue contexts in device dump collection. Patch 8 fixes cast from restricted __sum16 warning when saving IPv4 partial checksum. Patch 9 fixes issue with string array scope in DCB path. Patch 10 fixes a set but unused variable warning when DCB is disabled. Patch 11 fixes several kernel-doc comment warnings in cxgb4 driver. Patch 12 fixes several kernel-doc comment warnings in cxgb4vf driver. ==================== Signed-off-by: David S. Miller <[email protected]>
2020-06-23cxgb4vf: update kernel-doc line commentsRahul Lakkireddy3-11/+8
Update several kernel-doc line comments to fix warnings reported by make W=1. Fixes following class of warnings reported by make W=1 in several places: cxgb4vf_main.c:275: warning: Function parameter or member 'persistent' not described in 'cxgb4vf_change_mac' cxgb4vf_main.c:275: warning: Excess function parameter 'persist' description in 'cxgb4vf_change_mac' Fixes: 16f8bd4be754 ("cxgb4vf: Add core T4 PCI-E SR-IOV Virtual Function hardware definitions and device communication code") Fixes: c6e0d91464da ("cxgb4vf: Add T4 Virtual Function Scatter-Gather Engine DMA code") Fixes: e0a8b34a9cc4 ("cxgb4vf: Add and initialize some sge params for VF driver") Fixes: c3168cabe1af ("cxgb4/cxgbvf: Handle 32-bit fw port capabilities") Fixes: 0e23daeb6407 ("drivers/net: chelsio/cxgb*: Convert timers to use timer_setup()") Fixes: 3f8cfd0d95e6 ("cxgb4/cxgb4vf: Program hash region for {t4/t4vf}_change_mac()") Signed-off-by: Rahul Lakkireddy <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-06-23cxgb4: update kernel-doc line commentsRahul Lakkireddy8-30/+38
Update several kernel-doc line comments to fix warnings reported by make W=1. Fixes following class of warnings reported by make W=1 in several places: l2t.c:616: warning: Cannot understand * @dev: net_device pointer t4_hw.c:3175: warning: Function parameter or member 'adap' not described in 't4_get_exprom_version' t4_hw.c:3175: warning: Excess function parameter 'adapter' description in 't4_get_exprom_version' Fixes: 56d36be4dd5f ("cxgb4: Add HW and FW support code") Fixes: fd3a47900b6f ("cxgb4: Add packet queues and packet DMA code") Fixes: 26f7cbc0a5a4 ("cxgb4: Don't attempt to upgrade T4 firmware when cxgb4 will end up as a slave") Fixes: 793dad94e745 ("RDMA/cxgb4: Fix bug for active and passive LE hash collision path") Fixes: ba3f8cd55f2a ("cxgb4: Add support in cxgb4 to get expansion rom version via ethtool") Fixes: f7502659cec8 ("cxgb4: Add API to alloc l2t entry; also update existing ones") Fixes: ddc7740d9a7c ("cxgb4: Decode link down reason code obtained from firmware") Fixes: 193c4c2845f7 ("cxgb4: Update T6 Buffer Group and Channel Mappings") Fixes: 8f46d46715a1 ("cxgb4: Use Firmware params to get buffer-group map") Fixes: a456950445a0 ("cxgb4: time stamping interface for PTP") Fixes: 9c33e4208bce ("cxgb4: Add PTP Hardware Clock (PHC) support") Fixes: c3168cabe1af ("cxgb4/cxgbvf: Handle 32-bit fw port capabilities") Fixes: 5ccf9d049615 ("cxgb4: update API for TP indirect register access") Fixes: 3bdb376e6944 ("cxgb4: introduce SMT ops to prepare for SMAC rewrite support") Fixes: 736c3b94474e ("cxgb4: collect egress and ingress SGE queue contexts") Fixes: f56ec6766dcf ("cxgb4: Add support for ethtool i2c dump") Fixes: 9d5fd927d20b ("cxgb4/cxgb4vf: add support for ndo_set_vf_vlan") Fixes: 98f3697f8d41 ("cxgb4: add tc flower match support for tunnel VNI") Fixes: 02d805dc5fe3 ("cxgb4: use new fw interface to get the VIN and smt index") Fixes: 3f8cfd0d95e6 ("cxgb4/cxgb4vf: Program hash region for {t4/t4vf}_change_mac()") Fixes: d429005fdf2c ("cxgb4/cxgb4vf: Add support for SGE doorbell queue timer") Fixes: 0e395b3cb1fb ("cxgb4: add FLOWC based QoS offload") Signed-off-by: Rahul Lakkireddy <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-06-23cxgb4: fix set but unused variable when DCB is disabledRahul Lakkireddy1-3/+3
Remove the set but unused variable when DCB is disabled. Instead, do the calculation directly inline. Fixes following warning in make W=1: cxgb4_main.c: In function 'cfg_queues': cxgb4_main.c:5380:29: warning: variable 'n1g' set but not used [-Wunused-but-set-variable] u32 i, n10g = 0, qidx = 0, n1g = 0; ^ Fixes: 116ca924aea6 ("cxgb4: fix checks for max queues to allocate") Signed-off-by: Rahul Lakkireddy <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-06-23cxgb4: move DCB version extern to header fileRahul Lakkireddy2-1/+3
Move the DCB version string array extern to header file. Fixes following sparse warning: cxgb4_dcb.c:13:12: warning: symbol 'dcb_ver_array' was not declared. Should it be static? Fixes: ebddd97afb89 ("cxgb4: add support to display DCB info") Signed-off-by: Rahul Lakkireddy <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-06-23cxgb4: remove cast when saving IPv4 partial checksumRahul Lakkireddy1-2/+1
The checksum field in IPv4 header is in __sum16 and ip_fast_csum() also returns __sum16. So, no need to cast it to u16. Fixes following sparse warning: sge.c:1539:47: warning: cast from restricted __sum16 sge.c:1539:44: warning: incorrect type in assignment (different base types) sge.c:1539:44: expected restricted __sum16 [usertype] check sge.c:1539:44: got unsigned short [usertype] Fixes: d0a1299c6bf7 ("cxgb4: add support for vxlan segmentation offload") Signed-off-by: Rahul Lakkireddy <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-06-23cxgb4: fix SGE queue dump destination buffer contextRahul Lakkireddy1-2/+4
The data in destination buffer is expected to be be parsed in big endian. So, use the right context. Fixes following sparse warning: cudbg_lib.c:2041:44: warning: incorrect type in assignment (different base types) cudbg_lib.c:2041:44: expected unsigned long long [usertype] cudbg_lib.c:2041:44: got restricted __be64 [usertype] Fixes: 736c3b94474e ("cxgb4: collect egress and ingress SGE queue contexts") Signed-off-by: Rahul Lakkireddy <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-06-23cxgb4: use correct type for all-mask IP address comparisonRahul Lakkireddy1-5/+5
Use correct type to check for all-mask exact match IP addresses. Fixes following sparse warnings due to big endian value checks against 0xffffffff in is_addr_all_mask(): cxgb4_filter.c:977:25: warning: restricted __be32 degrades to integer cxgb4_filter.c:983:37: warning: restricted __be32 degrades to integer cxgb4_filter.c:984:37: warning: restricted __be32 degrades to integer cxgb4_filter.c:985:37: warning: restricted __be32 degrades to integer cxgb4_filter.c:986:37: warning: restricted __be32 degrades to integer Fixes: 3eb8b62d5a26 ("cxgb4: add support to create hash-filters via tc-flower offload") Signed-off-by: Rahul Lakkireddy <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-06-23cxgb4: fix endian conversions for L4 ports in filtersRahul Lakkireddy3-25/+22
The source and destination L4 ports in filter offload need to be in CPU endian. They will finally be converted to Big Endian after all operations are done and before giving them to hardware. The L4 ports for NAT are expected to be passed as a byte stream TCB. So, treat them as such. Fixes following sparse warnings in several places: cxgb4_tc_flower.c:159:33: warning: cast from restricted __be16 cxgb4_tc_flower.c:159:33: warning: incorrect type in argument 1 (different base types) cxgb4_tc_flower.c:159:33: expected unsigned short [usertype] val cxgb4_tc_flower.c:159:33: got restricted __be16 [usertype] dst Fixes: dca4faeb812f ("cxgb4: Add LE hash collision bug fix path in LLD driver") Fixes: 62488e4b53ae ("cxgb4: add basic tc flower offload support") Fixes: 557ccbf9dfa8 ("cxgb4: add tc flower support for L3/L4 rewrite") Signed-off-by: Rahul Lakkireddy <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-06-23cxgb4: parse TC-U32 key values and masks nativelyRahul Lakkireddy2-49/+91
TC-U32 passes all keys values and masks in __be32 format. The parser already expects this and hence pass the value and masks in __be32 natively to the parser. Fixes following sparse warnings in several places: cxgb4_tc_u32.c:57:21: warning: incorrect type in assignment (different base types) cxgb4_tc_u32.c:57:21: expected unsigned int [usertype] val cxgb4_tc_u32.c:57:21: got restricted __be32 [usertype] val cxgb4_tc_u32_parse.h:48:24: warning: cast to restricted __be32 Fixes: 2e8aad7bf203 ("cxgb4: add parser to translate u32 filters to internal spec") Signed-off-by: Rahul Lakkireddy <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-06-23cxgb4: use unaligned conversion for fetching timestampRahul Lakkireddy1-1/+1
Use get_unaligned_be64() to fetch the timestamp needed for ns_to_ktime() conversion. Fixes following sparse warning: sge.c:3282:43: warning: cast to restricted __be64 Fixes: a456950445a0 ("cxgb4: time stamping interface for PTP") Signed-off-by: Rahul Lakkireddy <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-06-23cxgb4: move PTP lock and unlock to caller in Tx pathRahul Lakkireddy1-12/+11
Check for whether PTP is enabled or not at the caller and perform locking/unlocking at the caller. Fixes following sparse warning: sge.c:1641:26: warning: context imbalance in 'cxgb4_eth_xmit' - different lock contexts for basic block Fixes: a456950445a0 ("cxgb4: time stamping interface for PTP") Signed-off-by: Rahul Lakkireddy <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-06-23cxgb4: move handling L2T ARP failures to callerRahul Lakkireddy1-28/+24
Move code handling L2T ARP failures to the only caller. Fixes following sparse warning: skbuff.h:2091:29: warning: context imbalance in 'handle_failed_resolution' - unexpected unlock Fixes: 749cb5fe48bb ("cxgb4: Replace arpq_head/arpq_tail with SKB double link-list code") Signed-off-by: Rahul Lakkireddy <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-06-23Merge branch 'net-qed-qede-various-stability-fixes'David S. Miller10-43/+80
Alexander Lobakin says: ==================== net: qed/qede: various stability fixes This set addresses several near-critical issues that were observed and reproduced on different test and production configurations. v2: - don't split the "Fixes:" tag across several lines in patch 9; - no functional changes. ==================== Signed-off-by: David S. Miller <[email protected]>
2020-06-23net: qed: fix "maybe uninitialized" warningAlexander Lobakin1-1/+1
Variable 'abs_ppfid' in qed_dev.c:qed_llh_add_mac_filter() always gets printed, but is initialized only under 'ref_cnt == 1' condition. This results in: In file included from ./include/linux/kernel.h:15:0, from ./include/asm-generic/bug.h:19, from ./arch/x86/include/asm/bug.h:86, from ./include/linux/bug.h:5, from ./include/linux/io.h:11, from drivers/net/ethernet/qlogic/qed/qed_dev.c:35: drivers/net/ethernet/qlogic/qed/qed_dev.c: In function 'qed_llh_add_mac_filter': ./include/linux/printk.h:358:2: warning: 'abs_ppfid' may be used uninitialized in this function [-Wmaybe-uninitialized] printk(KERN_NOTICE pr_fmt(fmt), ##__VA_ARGS__) ^~~~~~ drivers/net/ethernet/qlogic/qed/qed_dev.c:983:17: note: 'abs_ppfid' was declared here u8 filter_idx, abs_ppfid; ^~~~~~~~~ ...under W=1+. Fix this by initializing it with zero. Fixes: 79284adeb99e ("qed: Add llh ppfid interface and 100g support for offload protocols") Signed-off-by: Alexander Lobakin <[email protected]> Signed-off-by: Igor Russkikh <[email protected]> Signed-off-by: Michal Kalderon <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-06-23net: qed: reset ILT block sizes before recomputing to fix crashesAlexander Lobakin1-0/+19
Sizes of all ILT blocks must be reset before ILT recomputing when disabling clients, or memory allocation may exceed ILT shadow array and provoke system crashes. Fixes: 1408cc1fa48c ("qed: Introduce VFs") Signed-off-by: Alexander Lobakin <[email protected]> Signed-off-by: Igor Russkikh <[email protected]> Signed-off-by: Michal Kalderon <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-06-23net: qede: fix use-after-free on recovery and AER handlingAlexander Lobakin1-0/+1
Set edev->cdev pointer to NULL after calling remove() callback to avoid using of already freed object. Fixes: ccc67ef50b90 ("qede: Error recovery process") Signed-off-by: Alexander Lobakin <[email protected]> Signed-off-by: Igor Russkikh <[email protected]> Signed-off-by: Michal Kalderon <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-06-23net: qede: fix PTP initialization on recoveryAlexander Lobakin3-20/+15
Currently PTP cyclecounter and timecounter are initialized only on the first probing and are cleaned up during removal. This means that PTP becomes non-functional after device recovery. Fix this by unconditional PTP initialization on probing and clearing Tx pending bit on exiting. Fixes: ccc67ef50b90 ("qede: Error recovery process") Signed-off-by: Alexander Lobakin <[email protected]> Signed-off-by: Igor Russkikh <[email protected]> Signed-off-by: Michal Kalderon <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-06-23net: qed: fix excessive QM ILT lines consumptionAlexander Lobakin1-1/+1
This is likely a copy'n'paste mistake. The amount of ILT lines to reserve for a single VF was being multiplied by the total VFs count. This led to a huge redundancy in reservation and potential lines drainouts. Fixes: 1408cc1fa48c ("qed: Introduce VFs") Signed-off-by: Alexander Lobakin <[email protected]> Signed-off-by: Igor Russkikh <[email protected]> Signed-off-by: Michal Kalderon <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-06-23net: qed: fix NVMe login fails over VFsAlexander Lobakin1-5/+18
25ms sleep cycles in waiting for PF response are excessive and may lead to different timeout failures. Start to wait with short udelays, and in most cases polling will end here. If the time was not sufficient, switch to msleeps. usleep_range() may go far beyond 100us depending on platform and tick configuration, hence atomic udelays for consistency. Also add explicit DMA barriers since 'done' always comes from a shared request-response DMA pool, and note that in the comment nearby. Fixes: 1408cc1fa48c ("qed: Introduce VFs") Signed-off-by: Alexander Lobakin <[email protected]> Signed-off-by: Igor Russkikh <[email protected]> Signed-off-by: Michal Kalderon <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-06-23net: qede: stop adding events on an already destroyed workqueueAlexander Lobakin1-1/+2
Set rdma_wq pointer to NULL after destroying the workqueue and check for it when adding new events to fix crashes on driver unload. Fixes: cee9fbd8e2e9 ("qede: Add qedr framework") Signed-off-by: Alexander Lobakin <[email protected]> Signed-off-by: Igor Russkikh <[email protected]> Signed-off-by: Michal Kalderon <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Powered by cgit, Gruvboxed by Blaster4385.