| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
'clk-debugfs' into clk-next
* clk-versatile:
clk: versatile: Remove WARNs in ->round_rate()
clk: versatile: add min/max rate boundaries for vexpress osc clock
* clk-doc:
Documentation: clk: enable lock is not held for clk_is_enabled API
* clk-must-check:
clk: add more __must_check for bulk APIs
* clk-qcom:
clk: qcom: smd-rpm: Migrate to devm_of_clk_add_hw_provider()
clk: qcom: gcc-msm8996: Mark aggre0 noc clks as critical
* clk-debugfs:
clk: Re-use DEFINE_SHOW_ATTRIBUTE() macro
|
|
clk-next
* clk-ti:
clk: keystone: sci-clk: add support for dynamically probing clocks
clk: ti: add support for clock latching to mux clocks
clk: ti: add support for clock latching to divider clocks
clk: ti: add generic support for clock latching
clk: ti: add support for register read-modify-write low-level operation
dt-bindings: clock: ti: add latching support to mux and divider clocks
* clk-amlogic: (50 commits)
clk: meson: Drop unused local variable and add static
clk: meson: clean-up clk81 clocks
clk: meson: add fdiv clock gates
clk: meson: add mpll pre-divider
clk: meson: axg: add hifi pll clock
clk: meson: axg: add hifi clock bindings
clk: meson: add ROUND_CLOSEST to the pll driver
clk: meson: add gp0 frac parameter for axg and gxl
clk: meson: improve pll driver results with frac
clk: meson: remove special gp0 lock loop
clk: meson: poke pll CNTL last
clk: meson: add fractional part of meson8b fixed_pll
clk: meson: use hhi syscon if available
clk: meson: remove obsolete cpu_clk
clk: meson: rework meson8b cpu clock
clk: meson: split divider and gate part of mpll
clk: meson: migrate plls clocks to clk_regmap
clk: meson: migrate the audio divider clock to clk_regmap
clk: meson: migrate mplls clocks to clk_regmap
clk: meson: add regmap helpers for parm
...
* clk-tegra:
clk: tegra: Fix pll_u rate configuration
clk: tegra: Specify VDE clock rate
clk: tegra20: Correct PLL_C_OUT1 setup
clk: tegra: Mark HCLK, SCLK and EMC as critical
clk: tegra: MBIST work around for Tegra210
clk: tegra: add fence_delay for clock registers
clk: tegra: Add la clock for Tegra210
* clk-samsung: (22 commits)
clk: samsung: Mark a few things static
clk: samsung: Add fout=196608001 Hz EPLL rate entry for exynos4412
clk: samsung: exynos5250: Add missing clocks for FIMC LITE SYSMMU devices
clk: samsung: exynos5420: Add more entries to EPLL rate table
clk: samsung: exynos5420: Add CLK_SET_RATE_PARENT flag to mout_mau_epll_clk
clk: samsung: exynos5250: Move PD-dependent clocks to Exynos5 sub-CMU
clk: samsung: exynos5420: Move PD-dependent clocks to Exynos5 sub-CMU
clk: samsung: Add Exynos5 sub-CMU clock driver
soc: samsung: pm_domains: Add blacklisting clock handling
clk: samsung: Add compile time PLL rate validators
clk: samsung: s3c2410: Fix PLL rates
clk: samsung: exynos7: Fix PLL rates
clk: samsung: exynos5433: Fix PLL rates
clk: samsung: exynos5260: Fix PLL rates
clk: samsung: exynos5250: Fix PLL rates
clk: samsung: exynos3250: Fix PLL rates
clk: exynos5433: Extend list of available AUD_PLL output frequencies
clk: exynos5433: Add CLK_IGNORE_UNUSED flag to sclk_ioclk_i2s1_bclk
clk: samsung: Add a git tree entry to MAINTAINERS
clk: samsung: Remove redundant dev_err call in exynos_audss_clk_probe()
...
|
|
Pull MTD updates from Boris Brezillon:
"MTD Core:
- Remove support for asynchronous erase (not implemented by any of
the existing drivers anyway)
- Remove Cyrille from the list of SPI NOR and MTD maintainers
- Fix kernel doc headers
- Allow users to define the partitions parsers they want to test
through a DT property (compatible of the partitions subnode)
- Remove the bfin-async-flash driver (the only architecture using it
has been removed)
- Fix pagetest test
- Add extra checks in mtd_erase()
- Simplify the MTD partition creation logic and get rid of
mtd_add_device_partitions()
MTD Drivers:
- Add endianness information to the physmap DT binding
- Add Eon EN29LV400A IDs to JEDEC probe logic
- Use %*ph where appropriate
SPI NOR Drivers:
- Make fsl-quaspi assign different names to MTD devices connected to
the same QSPI controller
- Remove an unneeded driver.bus assigned in the fsl-qspi driver
NAND Core:
- Prepare arrival of the SPI NAND subsystem by implementing a generic
(interface-agnostic) layer to ease manipulation of NAND devices
- Move onenand code base to the drivers/mtd/nand/ dir
- Rework timing mode selection
- Provide a generic way for NAND chip drivers to flag a specific
GET/SET FEATURE operation as supported/unsupported
- Stop embedding ONFI/JEDEC param page in nand_chip
NAND Drivers:
- Rework/cleanup of the mxc driver
- Various cleanups in the vf610 driver
- Migrate the fsmc and vf610 to ->exec_op()
- Get rid of the pxa driver (replaced by marvell_nand)
- Support ->setup_data_interface() in the GPMI driver
- Fix probe error path in several drivers
- Remove support for unused hw_syndrome mode in sunxi_nand
- Various minor improvements"
* tag 'mtd/for-4.17' of git://git.infradead.org/linux-mtd: (89 commits)
dt-bindings: fsl-quadspi: Add the example of two SPI NOR
mtd: fsl-quadspi: Distinguish the mtd device names
mtd: nand: Fix some function description mismatches in core.c
mtd: fsl-quadspi: Remove unneeded driver.bus assignment
mtd: rawnand: marvell: Rename ->ecc_clk into ->core_clk
mtd: rawnand: s3c2410: enhance the probe function error path
mtd: rawnand: tango: fix probe function error path
mtd: rawnand: sh_flctl: fix the probe function error path
mtd: rawnand: omap2: fix the probe function error path
mtd: rawnand: mxc: fix probe function error path
mtd: rawnand: denali: fix probe function error path
mtd: rawnand: davinci: fix probe function error path
mtd: rawnand: cafe: fix probe function error path
mtd: rawnand: brcmnand: fix probe function error path
mtd: rawnand: sunxi: Stop supporting ECC_HW_SYNDROME mode
mtd: rawnand: marvell: Fix clock resource by adding a register clock
mtd: ftl: Use DIV_ROUND_UP()
mtd: Fix some function description mismatches in mtdcore.c
mtd: physmap_of: update struct map_info's swap as per map requirement
dt-bindings: mtd-physmap: Add endianness supports
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper updates from Mike Snitzer:
- DM core passthrough ioctl fix to retain reference to DM table, and
that table's block devices, while issuing the ioctl to one of those
block devices.
- DM core passthrough ioctl fix to _not_ override the fmode_t used to
issue the ioctl. Overriding by using the fmode_t that the block
device was originally open with during DM table load is a liability.
- Add DM core support for secure erase forwarding and update the DM
linear and DM striped targets to support them.
- A DM core 4.16 stable fix to allow abnormal IO (e.g. discard, write
same, write zeroes) for targets that make use of the non-splitting IO
variant (as is done for multipath or thinp when layered directly on
NVMe).
- Allow DM targets to return a payload in response to a DM message that
they are sent. This is useful for DM targets that would like to
provide statistics data in response to DM messages.
- Update DM bufio to support non-power-of-2 block sizes. Numerous other
related changes prepare the DM bufio code for this support.
- Fix DM crypt to use a bounded amount of memory across the entire
system. This is to avoid OOM that can otherwise occur in response to
certain pathological IO workloads (e.g. discarding a large DM crypt
device).
- Add a 'check_at_most_once' feature to the DM verity target to allow
verity to be used on mobile devices that have very limited resources.
- Fix the DM integrity target to fail early if a keyed algorithm (e.g.
HMAC) is to be used but the key isn't set.
- Add non-power-of-2 support to the DM unstripe target.
- Eliminate the use of a Variable Length Array in the DM stripe target.
- Update the DM log-writes target to record metadata (REQ_META flag).
- DM raid fixes for its nosync status and some variable range issues.
* tag 'for-4.17/dm-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm: (28 commits)
dm: remove fmode_t argument from .prepare_ioctl hook
dm: hold DM table for duration of ioctl rather than use blkdev_get
dm raid: fix parse_raid_params() variable range issue
dm verity: make verity_for_io_block static
dm verity: add 'check_at_most_once' option to only validate hashes once
dm bufio: don't embed a bio in the dm_buffer structure
dm bufio: support non-power-of-two block sizes
dm bufio: use slab cache for dm_buffer structure allocations
dm bufio: reorder fields in dm_buffer structure
dm bufio: relax alignment constraint on slab cache
dm bufio: remove code that merges slab caches
dm bufio: get rid of slab cache name allocations
dm bufio: move dm-bufio.h to include/linux/
dm bufio: delete outdated comment
dm: add support for secure erase forwarding
dm: backfill abnormal IO support to non-splitting IO submission
dm raid: fix nosync status
dm mpath: use DM_MAPIO_SUBMITTED instead of magic number 0 in process_queued_bios()
dm stripe: get rid of a Variable Length Array (VLA)
dm log writes: record metadata flag for better flags record
...
|
|
A block of email options is added under the optional config section.
Link: http://lkml.kernel.org/r/[email protected]
Suggested-by: Dhaval Giani <[email protected]>
Signed-off-by: Tim Tianyang Chen <[email protected]>
Signed-off-by: Steven Rostedt (VMware) <[email protected]>
|
|
Users should get emails when the script dies because of a critical failure.
Critical failures are defined as any errors that could abnormally terminate
the script.
In order to add email support, this patch converts all die() to dodie() except:
* when '-v' is used as an option to get the version of the script.
* in Sig-Int handeler because it's not a fatal error to cancel the script.
* errors happen during parsing config
Link: http://lkml.kernel.org/r/[email protected]
Suggested-by: Dhaval Giani <[email protected]>
Signed-off-by: Tim Tianyang Chen <[email protected]>
Signed-off-by: Steven Rostedt (VMware) <[email protected]>
|
|
Add clk driver support for imx6sll.
Signed-off-by: Bai Ping <[email protected]>
Acked-by: Dong Aisheng <[email protected]>
Signed-off-by: Stephen Boyd <[email protected]>
|
|
Add clock binding doc update for imx6sll.
Signed-off-by: Bai Ping <[email protected]>
Acked-by: Dong Aisheng <[email protected]>
Signed-off-by: Stephen Boyd <[email protected]>
|
|
Add new gate/gate2 wrapper function to register clocks with optional flags.
Signed-off-by: Bai Ping <[email protected]>
Acked-by: Dong Aisheng <[email protected]>
Signed-off-by: Stephen Boyd <[email protected]>
|
|
The busy divider and busy mux is actually used by the system critical clocks,
so add 'CLK_IS_CRITICAL' to clocks registered with these two type.
Signed-off-by: Bai Ping <[email protected]>
Acked-by: Dong Aisheng <[email protected]>
Signed-off-by: Stephen Boyd <[email protected]>
|
|
User can cancel tests and specify handler's behavior using option
'EMAIL_WHEN_CANCELED'.
Link: http://lkml.kernel.org/r/[email protected]
Suggested-by: Dhaval Giani <[email protected]>
Signed-off-by: Tim Tianyang Chen <[email protected]>
Signed-off-by: Steven Rostedt (VMware) <[email protected]>
|
|
Users can define optional variables to get email notifications.
Ktest can send emails when the script:
* was started
* failed with fatal errors and called dodie()
* completed all testing
Users have to setup the mailer provided in config prior to using this script.
Supported mailers: mailx, mail, sendmail
mailer specific routines are _sendmail_send(), _mailx_send()
Link: http://lkml.kernel.org/r/[email protected]
Suggested-by: Dhaval Giani <[email protected]>
Signed-off-by: Tim Tianyang Chen <[email protected]>
Signed-off-by: Steven Rostedt (VMware) <[email protected]>
|
|
Use SET_LATE_SYSTEM_SLEEP_PM_OPS() macro instead of direct assignment to
.resume_early field.
This fixes initialization of CS2000 in restore from hibernation in case
of kernel used to load image did not initialize CS2000 while kernel
being restored had CS2000 initialized.
Signed-off-by: Nikita Yushchenko <[email protected]>
Signed-off-by: Stephen Boyd <[email protected]>
|
|
In order to enable a PLL, not only the PLL has to be powered up and
locked, but you also have to de-assert the reset signal. The last part
was missing. Add it so PLLs that were not enabled by the FW/bootloader
can be enabled from Linux.
Fixes: 41691b8862e2 ("clk: bcm2835: Add support for programming the audio domain clocks")
Cc: <[email protected]>
Signed-off-by: Boris Brezillon <[email protected]>
Reviewed-by: Eric Anholt <[email protected]>
Signed-off-by: Stephen Boyd <[email protected]>
|
|
If a config-bisect was interrupted, then allow the user to continue, or
restart a new config-bisect.
Signed-off-by: Steven Rostedt (VMware) <[email protected]>
|
|
Just looking for config-bisect.pl in the source tree can be risky,
especially, if the source tree being tested doesn't have config-bisect.pl in
place. Instead, allow the user to set where to find config-bisect.pl with a
new option CONFIG_BISECT_EXEC.
If this option is not set, by default, ktest.pl will look for
config-bisect.pl in the following locations:
`pwd`/config-bisect.pl # where ktest.pl was called from
`dirname /path/to/ktest.pl`/config-bisect.pl # where ktest.pl exists
${BUILD_DIR}/tools/testing/ktest/config-bisect.pl
# where config-bisect.pl exists in the source tree.
Signed-off-by: Steven Rostedt (VMware) <[email protected]>
|
|
If config-bisect.pl sees that a config_bisect has already been started, it
will ask on the command line if it should bisect or not. This will mess up
running config_bisect from ktest.pl.
Have ktest.pl pass in '-r' to config-bisect.pl and have config-bisect.pl
recognize that to reset without asking.
Signed-off-by: Steven Rostedt (VMware) <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull misc vfs updates from Al Viro:
"Assorted stuff, including Christoph's I_DIRTY patches"
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs: move I_DIRTY_INODE to fs.h
ubifs: fix bogus __mark_inode_dirty(I_DIRTY_SYNC | I_DIRTY_DATASYNC) call
ntfs: fix bogus __mark_inode_dirty(I_DIRTY_SYNC | I_DIRTY_DATASYNC) call
gfs2: fix bogus __mark_inode_dirty(I_DIRTY_SYNC | I_DIRTY_DATASYNC) calls
fs: fold open_check_o_direct into do_dentry_open
vfs: Replace stray non-ASCII homoglyph characters with their ASCII equivalents
vfs: make sure struct filename->iname is word-aligned
get rid of pointless includes of fs_struct.h
[poll] annotate SAA6588_CMD_POLL users
|
|
Check to see if diffconfig is available and use that to diff the configs
instead of using 'diff -u', as diffconfig produces much better output of
kernel config files. It checks the source directory for the executable.
Signed-off-by: Steven Rostedt (VMware) <[email protected]>
|
|
When commands are run in ktest, they are only displayed in the ktest log
file, but that is not sufficient for outputting the display for config
bisects. The result of a config bisect is not shown.
Add a way to display the output of "run_command" which is the subroutine
used by ktest to execute commands. Use this feature to display the output of
config-bisect.pl executions to see the progress as well as the result.
Signed-off-by: Steven Rostedt (VMware) <[email protected]>
|
|
Reduce code duplication and take advantage of bisection logic
improvements by calling config-bisect.pl.
The output of make oldconfig is now copied directly to the desired file,
rather than doing assign_configs+save_config, in order to preserve the
ordering so that diffing the configs at the end will provide useful
output.
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Scott Wood <[email protected]>
[ Modified to use with new version of config-bisect.pl ]
Signed-off-by: Steven Rostedt (VMware) <[email protected]>
|
|
Started working on a stand alone program that can do a config bisect. It is
based on the config bisect code of ktest.pl. Instead of needing all the
infrastructure of ktest.pl, all that is required for config-bisect.pl is two
config files. One that works, and one that does not. The goal is to pass in
the two files, and it will create a new "good" and a new "bad" config file
based on input from the user. After several iterations (calls to this
program), it will eventually end with a minimum config value that allows one
config to work and the other config to break.
The program uses a technique that takes the good config and then makes half
of the configs that differ from the bad config just like the bad config.
The code will use make oldconfig to make sure the configs that are set are
not all converted back due to incorrect dependencies on other configs set in
the bad config but not in the new test config.
This is still a work in progress, but as it was written while I was working
at Red Hat, I want this code to be submitted as such.
Signed-off-by: Steven Rostedt (Red Hat) <[email protected]>
|
|
The LED2[2]/INTn pin on Marvell 88E1318S as well as 88E1510/12/14/18 needs
to be configured to be usable as interrupt not only when WOL is enabled,
but whenever we rely on interrupts from the PHY.
Signed-off-by: Esben Haabendal <[email protected]>
Cc: Rasmus Villemoes <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
For init on clocks we should move it at the first place in imx7d_clocks_init()
before any clock operations, else the clock operation may fail in case the clock
is still not on.
Acked-by: Ranjani Vaidyanathan <[email protected]>
Signed-off-by: Dong Aisheng <[email protected]>
Signed-off-by: Irina Tirdea <[email protected]>
Signed-off-by: Abel Vesa <[email protected]>
Signed-off-by: Stephen Boyd <[email protected]>
|
|
Design team change the ahb's clk parent options but
did NOT update the DOC accordingly in time, so the
AHB/IPG's clk rate in clk tree is incorrect, AHB is
67.5MHz and IPG is 33.75MHz, but using scope to
monitor them, they are actually 135MHz and 67.5MHz,
update the clk parent option to make clk tree info
correct.
Signed-off-by: Anson Huang <[email protected]>
Signed-off-by: Irina Tirdea <[email protected]>
Signed-off-by: Abel Vesa <[email protected]>
Signed-off-by: Stephen Boyd <[email protected]>
|
|
DRAM PLL is a audio/video type PLL, need to correct
it to get correct ops of PLL.
There is a test_div placed before DRAM PLL's gate, so
add this test div clk.
Signed-off-by: Anson Huang <[email protected]>
Signed-off-by: Irina Tirdea <[email protected]>
Signed-off-by: Abel Vesa <[email protected]>
Signed-off-by: Stephen Boyd <[email protected]>
|
|
Add USB clock information, the pll_usb_main_clk is USB_PLL at CCM
which is the output of USBOTG2 PHY.
Signed-off-by: Peter Chen <[email protected]>
Signed-off-by: Irina Tirdea <[email protected]>
Signed-off-by: Abel Vesa <[email protected]>
Signed-off-by: Stephen Boyd <[email protected]>
|
|
Add a clock driver for the Stratix10 SoC. The driver is similar to the
Cyclone5/Arria10 platforms, with the exception that this driver only uses
one single clock binding.
Signed-off-by: Dinh Nguyen <[email protected]>
Signed-off-by: Stephen Boyd <[email protected]>
|
|
Document that Stratix10 clock bindings, and add the clock header file. The
clock header is an enumeration of all the different clocks on the Stratix10
platform.
Signed-off-by: Dinh Nguyen <[email protected]>
Reviewed-by: Rob Herring <[email protected]>
Signed-off-by: Stephen Boyd <[email protected]>
|
|
Make the function static to avoid a
warning: no previous prototype for ‘vmx_enable_tdp’
Signed-off-by: Peng Hao <[email protected]>
Signed-off-by: Paolo Bonzini <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2018-04-06
This series contains a couple of fixes for the new ice driver.
Wei Yongjun fixes the return error code for error case during init.
Anirudh fixes the incorrect use of ARRAY_SIZE() in the ice ethtool code
and fixed "for" loop calculations.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
The per-browser screen refresh routine (ui_browser->refresh()) should
return the first row that should be cleaned after the rows just printed,
in case not all rows available on the screen gets filled.
When moving the extra title lines logic from the hists browser to the
generic ui_browser class, one piece of that logic remained in the hists
browser and then when going back from the annotate browser to the hists
browser in a case where fewer lines were displayed in the hists browser,
for instance when filtering the entries per substring, one line of the
annotate browser would remain on the screen, fix that.
Example of the screen artifact:
================================================================================
Samples: 73K of event 'cycles:ppp', 4000 Hz, Event count (approx.): 45172901394
Overhead Shared O Symbol
0.30% [kernel] [k] __indirect_thunk_start
0.09% [kernel] [k] __x86_indirect_thunk_r10
│ lfence
================================================================================
Here from 'perf top' the view was zoomed with '/thunk' to functions
having that substring, then the first was annotated and from the
annotate browser ESC was pressed, then the first lines were overwritten,
but the 'lfence' line remained due to the off by one bug fixed in this
cset.
Cc: Adrian Hunter <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: David Ahern <[email protected]>
Cc: Jin Yao <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Wang Nan <[email protected]>
Fixes: ef9ff6017e3c ("perf ui browser: Move the extra title lines from the hists browser")
Link: https://lkml.kernel.org/n/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
To help in fixing problems in the browser.
Cc: Adrian Hunter <[email protected]>
Cc: David Ahern <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Wang Nan <[email protected]>
Link: https://lkml.kernel.org/n/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
Switch simpad's CF implementation to use the gpiod APIs. The inverted
detection is handled using gpiolib's native inversion abilities.
Signed-off-by: Russell King <[email protected]>
|
|
Convert shannon to use the generic CF socket support.
Signed-off-by: Russell King <[email protected]>
|
|
Convert nanoengine to use the generic CF socket support.
Makefile fix from Arnd Bergmann <[email protected]>.
Signed-off-by: Russell King <[email protected]>
|
|
1) Return correct size from ice_get_regs_len.
2) Fix incorrect use of ARRAY_SIZE in ice_get_regs.
Fixes: fcea6f3da546 (ice: Add stats and ethtool support)
Signed-off-by: Anirudh Venkataramanan <[email protected]>
Tested-by: Tony Brelinski <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
Fix to return error code ICE_ERR_NO_MEMORY from the alloc error
handling case instead of 0, as done elsewhere in this function.
Fixes: dc49c7723676 ("ice: Get MAC/PHY/link info and scheduler topology")
Signed-off-by: Wei Yongjun <[email protected]>
Acked-by: Anirudh Venkataramanan <[email protected]>
Tested-by: Tony Brelinski <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
* lorenzo/pci/cadence:
MAINTAINERS: Add missing /drivers/pci/cadence directory entry
|
|
arch cris & metag have been removed from supported archs.
The dts hard link files should also be removed, or the ctags
tool will give warning.
execute"ctags -R", output:
ctags: Warning: cannot open source file
"scripts/dtc/include-prefixes/cris" : No such file or directory
ctags: Warning: cannot open source file
"scripts/dtc/include-prefixes/metag" : No such file or directory
Signed-off-by: Liu Changcheng <[email protected]>
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
Maintain a catalogue of allocated cookies so that cookie collisions can be
handled properly. For the moment, this just involves printing a warning
and returning a NULL cookie to the caller of fscache_acquire_cookie(), but
in future it might make sense to wait for the old cookie to finish being
cleaned up.
This requires the cookie key to be stored attached to the cookie so that we
still have the key available if the netfs relinquishes the cookie. This is
done by an earlier patch.
The catalogue also renders redundant fscache_netfs_list (used for checking
for duplicates), so that can be removed.
Signed-off-by: David Howells <[email protected]>
Acked-by: Anna Schumaker <[email protected]>
Tested-by: Steve Dickson <[email protected]>
|
|
Pass the object size in to fscache_acquire_cookie() and
fscache_write_page() rather than the netfs providing a callback by which it
can be received. This makes it easier to update the size of the object
when a new page is written that extends the object.
The current object size is also passed by fscache to the check_aux
function, obviating the need to store it in the aux data.
Signed-off-by: David Howells <[email protected]>
Acked-by: Anna Schumaker <[email protected]>
Tested-by: Steve Dickson <[email protected]>
|
|
With trace events set before and after the initcall function calls, instead
of having a separate routine for printing out the initcalls when
initcall_debug is specified on the kernel command line, have the code
register a callback to the tracepoints where the initcall trace events are.
This removes the need for having a separate function to do the initcalls as
the tracepoint callbacks can handle the printk. It also includes other
initcalls that are not called by the do_one_initcall() which includes
console and security initcalls.
Signed-off-by: Steven Rostedt (VMware) <[email protected]>
|
|
Trace events have been added around the initcall functions defined in
init/main.c. But console and security have their own initcalls. This adds
the trace events associated for those initcall functions.
Link: http://lkml.kernel.org/r/[email protected]
Cc: Ingo Molnar <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Signed-off-by: Abderrahmane Benbachir <[email protected]>
Signed-off-by: Steven Rostedt (VMware) <[email protected]>
|
|
Being able to trace the start and stop of initcalls is useful to see where
the timings are an issue. There is already an "initcall_debug" parameter,
but that can cause a large overhead itself, as the printing of the
information may take longer than the initcall functions.
Adding in a start and finish trace event around the initcall functions, as
well as a trace event that records the level of the initcalls, one can get a
much finer measurement of the times and interactions of the initcalls
themselves, as trace events are much lighter than printk()s.
Suggested-by: Abderrahmane Benbachir <[email protected]>
Signed-off-by: Steven Rostedt (VMware) <[email protected]>
|
|
A boot up test function update_pred_fn() dereferences filter->prog without
the proper rcu annotation.
To do this, we must also take the event_mutex first. Normally, this isn't
needed because this test function can not race with other use cases that
touch the event filters (it is disabled if any events are enabled).
Reported-by: kbuild test robot <[email protected]>
Fixes: 80765597bc587 ("tracing: Rewrite filter logic to be simpler and faster")
Signed-off-by: Steven Rostedt (VMware) <[email protected]>
|
|
ftrace_function_set_filter() referenences filter->prog without annotation
and sparse complains about it. It needs a rcu_dereference_protected()
wrapper.
Reported-by: kbuild test robot <[email protected]>
Fixes: 80765597bc587 ("tracing: Rewrite filter logic to be simpler and faster")
Signed-off-by: Steven Rostedt (VMware) <[email protected]>
|
|
In commit 932066a15335 ("tracing: Default to using trace_global_clock if
sched_clock is unstable"), the logic for deciding to override the
default clock if unstable was reversed from the earlier posting. I was
trying to reduce the width of the message by using an early return
rather than a if-block, but reverted back to using the if-block and
accidentally left the predicate inverted.
Link: http://lkml.kernel.org/r/[email protected]
Fixes: 932066a15335 ("tracing: Default to using trace_global_clock if sched_clock is unstable")
Signed-off-by: Chris Wilson <[email protected]>
Signed-off-by: Steven Rostedt (VMware) <[email protected]>
|
|
Function tracing can trace in NMIs and such. If the TSC is determined
to be unstable, the tracing clock will switch to the global clock on
boot up, unless "trace_clock" is specified on the kernel command line.
The global clock disables interrupts to access sched_clock_cpu(), and in
doing so can be done within lockdep internals (because of function
tracing and NMIs). This can trigger false lockdep splats.
The trace_clock_global() is special, best not to trace the irq logic
within it.
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Steven Rostedt (VMware) <[email protected]>
|
|
As si_mem_available() can say there is enough memory even though the memory
available is not useable by the ring buffer, it is best to not kill innocent
applications because the ring buffer is taking up all the memory while it is
trying to allocate a great deal of memory.
If the allocator is user space (because kernel threads can also increase the
size of the kernel ring buffer on boot up), then after si_mem_available()
says there is enough memory, set the OOM killer to kill the current task if
an OOM triggers during the allocation.
Link: http://lkml.kernel.org/r/[email protected]
Suggested-by: Michal Hocko <[email protected]>
Signed-off-by: Steven Rostedt (VMware) <[email protected]>
|