| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The use of buffer descriptor APP4 field (32-bit) for storing skb pointer
obviously does not work on 64-bit platforms.
As APP3 is also unused, we can use that to store the other half of 64-bit
pointer values.
Contrary to what is hinted at in commit message of commit 15bfe05c8d63
("net: ethernet: xilinx: Mark XILINX_LL_TEMAC broken on 64-bit")
there are no other pointers stored in cdmac_bd.
Signed-off-by: Esben Haabendal <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Support initialization with platdata, so the driver can be used on
non-device-tree platforms.
For currently supported device-tree platforms, the driver should behave
as before.
Signed-off-by: Esben Haabendal <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
As a side effect, a few error cases are fixed.
If of_iomap() of sdma_regs failed, no error code was returned. Fixed to
return -ENOMEM similar to of_iomap() fail of regs.
If sysfs_create_group() or register_netdev() failed, lp->phy_node was not
released.
Finally, the order in remove function is corrected to be reverse order
of what is done in probe, i.e. calling temac_mdio_teardown() last, so we
unregister the netdev that most likely is using the mdio_bus first.
Signed-off-by: Esben Haabendal <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Fixes: 65b2b4939a64 ("selftests: net: initial fib rule tests")
Signed-off-by: Hangbin Liu <[email protected]>
Reviewed-by: David Ahern <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Fix inconsistent IS_ERR and PTR_ERR in cpsw_probe,
The proper pointer to use is clk instead of mode.
This issue was detected with the help of Coccinelle.
Fixes: 83a8471ba255 ("net: ethernet: ti: cpsw: refactor probe to group common hw initialization")
Signed-off-by: YueHaibing <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The pvlock_page and hvclock_page variables are (as the name implies)
addresses to pages, created by the linker script.
But we declared them as just "extern u8" variables, which _works_, but
now that gcc does some more bounds checking, it causes warnings like
warning: array subscript 1 is outside array bounds of ‘u8[1]’
when we then access more than one byte from those variables.
Fix this by simply making the declaration of the variables match
reality, which makes the compiler happy too.
Signed-off-by: Linus Torvalds <[email protected]>
|
|
I'm not sure what made gcc warn about this code now. The 'ret' variable
does end up initialized in all cases, but it's definitely not obvious,
so the compiler is quite reasonable to warn about this.
So just add initialization to make it all much more obvious both to
compilers and to humans.
Signed-off-by: Linus Torvalds <[email protected]>
|
|
We already did this for clang, but now gcc has that warning too. Yes,
yes, the address may be unaligned. And that's kind of the point.
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Previously, during fragmentation after forwarding, skb->skb_iif isn't
preserved, i.e. 'ip_copy_metadata' does not copy skb_iif from given
'from' skb.
As a result, ip_do_fragment's creates fragments with zero skb_iif,
leading to inconsistent behavior.
Assume for example an eBPF program attached at tc egress (post
forwarding) that examines __sk_buff->ingress_ifindex:
- the correct iif is observed if forwarding path does not involve
fragmentation/refragmentation
- a bogus iif is observed if forwarding path involves
fragmentation/refragmentatiom
Fix, by preserving skb_iif during 'ip_copy_metadata'.
Signed-off-by: Shmulik Ladkani <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
mt76 patches for 5.2
* share more code across drivers
* new driver for MT7615 chipsets
* rework DMA API
* tx/rx performance optimizations
* use NAPI for tx cleanup on mt76x02
* AP mode support for USB devices
* USB stability fixes
* tx power handling fixes for 76x2
* endian fixes
|
|
In io_sqe_buffer_register() we allocate a number of arrays based on the
iov_len from the user-provided iov. While we limit iov_len to SZ_1G,
we can still attempt to allocate arrays exceeding MAX_ORDER.
On a 64-bit system with 4KiB pages, for an iov where iov_base = 0x10 and
iov_len = SZ_1G, we'll calculate that nr_pages = 262145. When we try to
allocate a corresponding array of (16-byte) bio_vecs, requiring 4194320
bytes, which is greater than 4MiB. This results in SLUB warning that
we're trying to allocate greater than MAX_ORDER, and failing the
allocation.
Avoid this by using kvmalloc() for allocations dependent on the
user-provided iov_len. At the same time, fix a leak of imu->bvec when
registration fails.
Full splat from before this patch:
WARNING: CPU: 1 PID: 2314 at mm/page_alloc.c:4595 __alloc_pages_nodemask+0x7ac/0x2938 mm/page_alloc.c:4595
Kernel panic - not syncing: panic_on_warn set ...
CPU: 1 PID: 2314 Comm: syz-executor326 Not tainted 5.1.0-rc7-dirty #4
Hardware name: linux,dummy-virt (DT)
Call trace:
dump_backtrace+0x0/0x2f0 include/linux/compiler.h:193
show_stack+0x20/0x30 arch/arm64/kernel/traps.c:158
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x110/0x190 lib/dump_stack.c:113
panic+0x384/0x68c kernel/panic.c:214
__warn+0x2bc/0x2c0 kernel/panic.c:571
report_bug+0x228/0x2d8 lib/bug.c:186
bug_handler+0xa0/0x1a0 arch/arm64/kernel/traps.c:956
call_break_hook arch/arm64/kernel/debug-monitors.c:301 [inline]
brk_handler+0x1d4/0x388 arch/arm64/kernel/debug-monitors.c:316
do_debug_exception+0x1a0/0x468 arch/arm64/mm/fault.c:831
el1_dbg+0x18/0x8c
__alloc_pages_nodemask+0x7ac/0x2938 mm/page_alloc.c:4595
alloc_pages_current+0x164/0x278 mm/mempolicy.c:2132
alloc_pages include/linux/gfp.h:509 [inline]
kmalloc_order+0x20/0x50 mm/slab_common.c:1231
kmalloc_order_trace+0x30/0x2b0 mm/slab_common.c:1243
kmalloc_large include/linux/slab.h:480 [inline]
__kmalloc+0x3dc/0x4f0 mm/slub.c:3791
kmalloc_array include/linux/slab.h:670 [inline]
io_sqe_buffer_register fs/io_uring.c:2472 [inline]
__io_uring_register fs/io_uring.c:2962 [inline]
__do_sys_io_uring_register fs/io_uring.c:3008 [inline]
__se_sys_io_uring_register fs/io_uring.c:2990 [inline]
__arm64_sys_io_uring_register+0x9e0/0x1bc8 fs/io_uring.c:2990
__invoke_syscall arch/arm64/kernel/syscall.c:35 [inline]
invoke_syscall arch/arm64/kernel/syscall.c:47 [inline]
el0_svc_common.constprop.0+0x148/0x2e0 arch/arm64/kernel/syscall.c:83
el0_svc_handler+0xdc/0x100 arch/arm64/kernel/syscall.c:129
el0_svc+0x8/0xc arch/arm64/kernel/entry.S:948
SMP: stopping secondary CPUs
Dumping ftrace buffer:
(ftrace buffer empty)
Kernel Offset: disabled
CPU features: 0x002,23000438
Memory Limit: none
Rebooting in 1 seconds..
Fixes: edafccee56ff3167 ("io_uring: add support for pre-mapped user IO buffers")
Signed-off-by: Mark Rutland <[email protected]>
Cc: Alexander Viro <[email protected]>
Cc: Jens Axboe <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Signed-off-by: Jens Axboe <[email protected]>
|
|
Vinicius Costa Gomes says:
====================
net/sched: taprio change schedules
Changes from RFC:
- Removed the patches for taprio offloading, because of the lack of
in-tree users;
- Updated the links to point to the PATCH version of this series;
Original cover letter:
Overview
--------
This RFC has two objectives, it adds support for changing the running
schedules during "runtime", explained in more detail later, and
proposes an interface between taprio and the drivers for hardware
offloading.
These two different features are presented together so it's clear what
the "final state" would look like. But after the RFC stage, they can
be proposed (and reviewed) separately.
Changing the schedules without disrupting traffic is important for
handling dynamic use cases, for example, when streams are
added/removed and when the network configuration changes.
Hardware offloading support allows schedules to be more precise and
have lower resource usage.
Changing schedules
------------------
The same as the other interfaces we proposed, we try to use the same
concepts as the IEEE 802.1Q-2018 specification. So, for changing
schedules, there are an "oper" (operational) and an "admin" schedule.
The "admin" schedule is mutable and not in use, the "oper" schedule is
immutable and is in use.
That is, when the user first adds an schedule it is in the "admin"
state, and it becomes "oper" when its base-time (basically when it
starts) is reached.
What this means is that now it's possible to create taprio with a schedule:
$ tc qdisc add dev IFACE parent root handle 100 taprio \
num_tc 3 \
map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 \
queues 1@0 1@1 2@2 \
base-time 10000000 \
sched-entry S 03 300000 \
sched-entry S 02 300000 \
sched-entry S 06 400000 \
clockid CLOCK_TAI
And then, later, after the previous schedule is "promoted" to "oper",
add a new ("admin") schedule to be used some time later:
$ tc qdisc change dev IFACE parent root handle 100 taprio \
base-time 1553121866000000000 \
sched-entry S 02 500000 \
sched-entry S 0f 400000 \
clockid CLOCK_TAI
When enabling the ability to change schedules, it makes sense to add
two more defined knobs to schedules: "cycle-time" allows to truncate a
cycle to some value, so it repeats after a well-defined value;
"cycle-time-extension" controls how much an entry can be extended if
it's the last one before the change of schedules, the reason is to
avoid a very small cycle when transitioning from a schedule to
another.
With these, taprio in the software mode should provide a fairly
complete implementation of what's defined in the Enhancements for
Scheduled Traffic parts of the specification.
Hardware offload
----------------
Some workloads require better guarantees from their schedules than
what's provided by the software implementation. This series proposes
an interface for configuring schedules into compatible network
controllers.
This part is proposed together with the support for changing
schedules, because it raises questions like, should the "qdisc" side
be responsible of providing visibility into the schedules or should it
be the driver?
In this proposal, the driver is called passing the new schedule as
soon as it is validated, and the "core" qdisc takes care of displaying
(".dump()") the correct schedules at all times. It means that some
logic would need to be duplicated in the driver, if the hardware
doesn't have support for multiple schedules. But as taprio doesn't
have enough information about the underlying controller to know how
much in advance a schedule needs to be informed to the hardware, it
feels like a fair compromise.
The hardware offloading part of this proposal also tries to define an
interface for frame-preemption and how it interacts with the
scheduling of traffic, see Section 8.6.8.4 of IEEE 802.1Q-2018 for
more information.
One important difference between the qdisc interface and the
qdisc-driver interface, is that the "gate mask" on the qdisc side
references traffic classes, that is bit 0 of the gate mask means
Traffic Class 0, and in the driver interface, it specifies the queues,
that is bit 0 means queue 0. That is to say that taprio converts the
references to traffic classes to references to queues before sending
the offloading request to the driver.
Request for help
----------------
I would like that interested driver maintainers could take a look at
the proposed interface and see if it's going to be too awkward for any
particular device. Also, pointers to available documentation would be
appreciated. The idea here is to start a discussion so we can have an
interface that would work for multiple vendors.
Links
-----
kernel patches:
https://github.com/vcgomes/net-next/tree/taprio-add-support-for-change-v3
iproute2 patches:
https://github.com/vcgomes/iproute2/tree/taprio-add-support-for-change-v3
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
IEEE 802.1Q-2018 defines the concept of a cycle-time-extension, so the
last entry of a schedule before the start of a new schedule can be
extended, so "too-short" entries can be avoided.
Signed-off-by: Vinicius Costa Gomes <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
IEEE 802.1Q-2018 defines that a the cycle-time of a schedule may be
overridden, so the schedule is truncated to a determined "width".
Signed-off-by: Vinicius Costa Gomes <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The IEEE 802.1Q-2018 defines two "types" of schedules, the "Oper" (from
operational?) and "Admin" ones. Up until now, 'taprio' only had
support for the "Oper" one, added when the qdisc is created. This adds
support for the "Admin" one, which allows the .change() operation to
be supported.
Just for clarification, some quick (and dirty) definitions, the "Oper"
schedule is the currently (as in this instant) running one, and it's
read-only. The "Admin" one is the one that the system configurator has
installed, it can be changed, and it will be "promoted" to "Oper" when
it's 'base-time' is reached.
The idea behing this patch is that calling something like the below,
(after taprio is already configured with an initial schedule):
$ tc qdisc change taprio dev IFACE parent root \
base-time X \
sched-entry <CMD> <GATES> <INTERVAL> \
...
Will cause a new admin schedule to be created and programmed to be
"promoted" to "Oper" at instant X. If an "Admin" schedule already
exists, it will be overwritten with the new parameters.
Up until now, there was some code that was added to ease the support
of changing a single entry of a schedule, but was ultimately unused.
Now, that we have support for "change" with more well thought
semantics, updating a single entry seems to be less useful.
So we remove what is in practice dead code, and return a "not
supported" error if the user tries to use it. If changing a single
entry would make the user's life easier we may ressurrect this idea,
but at this point, removing it simplifies the code.
For now, only the schedule specific bits are allowed to be added for a
new schedule, that means that 'clockid', 'num_tc', 'map' and 'queues'
cannot be modified.
Example:
$ tc qdisc change dev IFACE parent root handle 100 taprio \
base-time $BASE_TIME \
sched-entry S 00 500000 \
sched-entry S 0f 500000 \
clockid CLOCK_TAI
The only change in the netlink API introduced by this change is the
introduction of an "admin" type in the response to a dump request,
that type allows userspace to separate the "oper" schedule from the
"admin" schedule. If userspace doesn't support the "admin" type, it
will only display the "oper" schedule.
Signed-off-by: Vinicius Costa Gomes <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Right now, this isn't a problem, but the next commit allows schedules
to be added during runtime. When a new schedule transitions from the
inactive to the active state ("admin" -> "oper") the previous one can
be freed, if it's freed just after the RCU read lock is released, we
may access an invalid entry.
So, we should take care to protect the dequeue() flow, so all the
places that access the entries are protected by the RCU read lock.
Signed-off-by: Vinicius Costa Gomes <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Yuchung Cheng says:
====================
undo congestion window on spurious SYN or SYNACK timeout
Linux TCP currently uses the initial congestion window of 1 packet
if multiple SYN or SYNACK timeouts per RFC6298. However such
timeouts are often spurious on wireless or cellular networks that
experience high delay variances (e.g. ramping up dormant radios or
local link retransmission). Another case is when the underlying
path is longer than the default SYN timeout (e.g. 1 second). In
these cases starting the transfer with a minimal congestion window
is detrimental to the performance for short flows.
One naive approach is to simply ignore SYN or SYNACK timeouts and
always use a larger or default initial window. This approach however
risks pouring gas to the fire when the network is already highly
congested. This is particularly true in data center where application
could start thousands to millions of connections over a single or
multiple hosts resulting in high SYN drops (e.g. incast).
This patch-set detects spurious SYN and SYNACK timeouts upon
completing the handshake via the widely-supported TCP timestamp
options. Upon such events the sender reverts to the default
initial window to start the data transfer so it gets best of both
worlds. This patch-set supports this feature for both active and
passive as well as Fast Open or regular connections.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
Relocate the congestion window initialization from tcp_init_metrics()
to tcp_init_transfer() to improve code readability.
Signed-off-by: Yuchung Cheng <[email protected]>
Signed-off-by: Neal Cardwell <[email protected]>
Signed-off-by: Soheil Hassas Yeganeh <[email protected]>
Signed-off-by: Eric Dumazet <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Use a helper to consolidate two identical code block for passive TFO.
Signed-off-by: Yuchung Cheng <[email protected]>
Signed-off-by: Neal Cardwell <[email protected]>
Signed-off-by: Soheil Hassas Yeganeh <[email protected]>
Signed-off-by: Eric Dumazet <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This patch makes passive Fast Open reverts the cwnd to default
initial cwnd (10 packets) if the SYNACK timeout is spurious.
Passive Fast Open uses a full socket during handshake so it can
use the existing undo logic to detect spurious retransmission
by recording the first SYNACK timeout in key state variable
retrans_stamp. Upon receiving the ACK of the SYNACK, if the socket
has sent some data before the timeout, the spurious timeout
is detected by tcp_try_undo_recovery() in tcp_process_loss()
in tcp_ack().
But if the socket has not send any data yet, tcp_ack() does not
execute the undo code since no data is acknowledged. The fix is to
check such case explicitly after tcp_ack() during the ACK processing
in SYN_RECV state. In addition this is checked in FIN_WAIT_1 state
in case the server closes the socket before handshake completes.
Signed-off-by: Yuchung Cheng <[email protected]>
Signed-off-by: Neal Cardwell <[email protected]>
Signed-off-by: Soheil Hassas Yeganeh <[email protected]>
Signed-off-by: Eric Dumazet <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
TCP sender would use congestion window of 1 packet on the second SYN
and SYNACK timeout except passive TCP Fast Open. This makes passive
TFO too aggressive and unfair during congestion at handshake. This
patch fixes this issue so TCP (fast open or not, passive or active)
always conforms to the RFC6298.
Note that tcp_enter_loss() is called only once during recurring
timeouts. This is because during handshake, high_seq and snd_una
are the same so tcp_enter_loss() would incorrect set the undo state
variables multiple times.
Signed-off-by: Yuchung Cheng <[email protected]>
Signed-off-by: Neal Cardwell <[email protected]>
Signed-off-by: Eric Dumazet <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Linux implements RFC6298 and use an initial congestion window
of 1 upon establishing the connection if the SYNACK packet is
retransmitted 2 or more times. In cellular networks SYNACK timeouts
are often spurious if the wireless radio was dormant or idle. Also
some network path is longer than the default SYNACK timeout. In
both cases falsely starting with a minimal cwnd are detrimental
to performance.
This patch avoids doing so when the final ACK's TCP timestamp
indicates the original SYNACK was delivered. It remembers the
original SYNACK timestamp when SYNACK timeout has occurred and
re-uses the function to detect spurious SYN timeout conveniently.
Note that a server may receives multiple SYNs from and immediately
retransmits SYNACKs without any SYNACK timeout. This often happens
on when the client SYNs have timed out due to wireless delay
above. In this case since the server will still use the default
initial congestion (e.g. 10) because tp->undo_marker is reset in
tcp_init_metrics(). This is an intentional design because packets
are not lost but delayed.
This patch only covers regular TCP passive open. Fast Open is
supported in the next patch.
Signed-off-by: Yuchung Cheng <[email protected]>
Signed-off-by: Neal Cardwell <[email protected]>
Signed-off-by: Eric Dumazet <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Detecting spurious SYNACK timeout using timestamp option requires
recording the exact SYNACK skb timestamp. Previously the SYNACK
sent timestamp was stamped slightly earlier before the skb
was transmitted. This patch uses the SYNACK skb transmission
timestamp directly.
Signed-off-by: Yuchung Cheng <[email protected]>
Signed-off-by: Neal Cardwell <[email protected]>
Signed-off-by: Eric Dumazet <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Linux implements RFC6298 and use an initial congestion window of 1
upon establishing the connection if the SYN packet is retransmitted 2
or more times. In cellular networks SYN timeouts are often spurious
if the wireless radio was dormant or idle. Also some network path
is longer than the default SYN timeout. Having a minimal cwnd on
both cases are detrimental to TCP startup performance.
This patch extends TCP undo feature (RFC3522 aka TCP Eifel) to detect
spurious SYN timeout via TCP timestamps. Since tp->retrans_stamp
records the initial SYN timestamp instead of first retransmission, we
have to implement a different undo code additionally. The detection
also must happen before tcp_ack() as retrans_stamp is reset when
SYN is acknowledged.
Note this patch covers both active regular and fast open.
Signed-off-by: Yuchung Cheng <[email protected]>
Signed-off-by: Neal Cardwell <[email protected]>
Signed-off-by: Eric Dumazet <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Previously if an active TCP open has SYN timeout, it always undo the
cwnd upon receiving the SYNACK. This is because tcp_clean_rtx_queue
would reset tp->retrans_stamp when SYN is acked, which fools then
tcp_try_undo_loss and tcp_packet_delayed. Addressing this issue is
required to properly support undo for spurious SYN timeout.
Fixing this is tricky -- for active TCP open tp->retrans_stamp
records the time when the handshake starts, not the first
retransmission time as the name may suggest. The simplest fix is
for tcp_packet_delayed to ensure it is valid before comparing with
other timestamp.
One side effect of this change is active TCP Fast Open that incurred
SYN timeout. Upon receiving a SYN-ACK that only acknowledged
the SYN, it would immediately retransmit unacknowledged data in
tcp_ack() because the data is marked lost after SYN timeout. But
the retransmission would have an incorrect ack sequence number since
rcv_nxt has not been updated yet tcp_rcv_synsent_state_process(), the
retransmission needs to properly handed by tcp_rcv_fastopen_synack()
like before.
Signed-off-by: Yuchung Cheng <[email protected]>
Signed-off-by: Neal Cardwell <[email protected]>
Signed-off-by: Eric Dumazet <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
update_chksum() accesses nskb->sk before it has been set
by complete_skb(), move the init up.
Fixes: e8f69799810c ("net/tls: Add generic NIC offload infrastructure")
Signed-off-by: Jakub Kicinski <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Replace "pass through" with a proper "fall through" annotation
in order to fix the following warning:
drivers/net/netdevsim/bus.c: In function ‘new_device_store’:
drivers/net/netdevsim/bus.c:170:14: warning: this statement may fall through [-Wimplicit-fallthrough=]
port_count = 1;
~~~~~~~~~~~^~~
drivers/net/netdevsim/bus.c:172:2: note: here
case 2:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This fix is part of the ongoing efforts to enable
-Wimplicit-fallthrough
Signed-off-by: Gustavo A. R. Silva <[email protected]>
Acked-by: Jakub Kicinski <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
A recent commit returns an error if icmp is used as the ip-proto for
IPv6 fib rules. Update fib_rule_tests to send ipv6-icmp instead of icmp.
Fixes: 5e1a99eae8499 ("ipv4: Add ICMPv6 support when parse route ipproto")
Signed-off-by: David Ahern <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Packet sockets in datagram mode take a destination address. Verify its
length before passing to dev_hard_header.
Prior to 2.6.14-rc3, the send code ignored sll_halen. This is
established behavior. Directly compare msg_namelen to dev->addr_len.
Change v1->v2: initialize addr in all paths
Fixes: 6b8d95f1795c4 ("packet: validate address length if non-zero")
Suggested-by: David Laight <[email protected]>
Signed-off-by: Willem de Bruijn <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Packet send checks that msg_name is at least sizeof sockaddr_ll.
Packet recv must return at least this length, so that its output
can be passed unmodified to packet send.
This ceased to be true since adding support for lladdr longer than
sll_addr. Since, the return value uses true address length.
Always return at least sizeof sockaddr_ll, even if address length
is shorter. Zero the padding bytes.
Change v1->v2: do not overwrite zeroed padding again. use copy_len.
Fixes: 0fb375fb9b93 ("[AF_PACKET]: Allow for > 8 byte hardware addresses.")
Suggested-by: David Laight <[email protected]>
Signed-off-by: Willem de Bruijn <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Normally firmware messages are printed with debugging enabled only. It's
a good idea as firmware may print a lot of messages that normal users
don't need to care about.
However, on firmware crash, it may be very helpful to log all recent
messages. There is almost always a backtrace available as well as rought
info on the latest actions/state.
Signed-off-by: Rafał Miłecki <[email protected]>
Reviewed-by: Arend van Spriel <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
Some PCIE firmwares drop txstatus if pktid is 0 and make packet held in
host side and never be released. If that packet type is 802.1x, the
pend_8021x_cnt value will be always greater than 0 and show "Timed out
waiting for no pending 802.1x packets" error message when sending key to
dongle every time.
To be compatible with all firmwares, host should set txflow request id
from 1 instead of from 0.
Signed-off-by: Wright Feng <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
If "ret_len" is negative then it could lead to a NULL dereference.
The "ret_len" value comes from nl80211_vendor_cmd(), if it's negative
then we don't allocate the "dcmd_buf" buffer. Then we pass "ret_len" to
brcmf_fil_cmd_data_set() where it is cast to a very high u32 value.
Most of the functions in that call tree check whether the buffer we pass
is NULL but there are at least a couple places which don't such as
brcmf_dbg_hex_dump() and brcmf_msgbuf_query_dcmd(). We memcpy() to and
from the buffer so it would result in a NULL dereference.
The fix is to change the types so that "ret_len" can't be negative. (If
we memcpy() zero bytes to NULL, that's a no-op and doesn't cause an
issue).
Fixes: 1bacb0487d0e ("brcmfmac: replace cfg80211 testmode with vendor command")
Signed-off-by: Dan Carpenter <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warning:
drivers/net/ethernet/sfc/mcdi_port.c: In function ‘efx_mcdi_phy_decode_link’:
./include/linux/compiler.h:77:22: warning: this statement may fall through [-Wimplicit-fallthrough=]
# define unlikely(x) __builtin_expect(!!(x), 0)
^~~~~~~~~~~~~~~~~~~~~~~~~~
./include/asm-generic/bug.h:125:2: note: in expansion of macro ‘unlikely’
unlikely(__ret_warn_on); \
^~~~~~~~
drivers/net/ethernet/sfc/mcdi_port.c:344:3: note: in expansion of macro ‘WARN_ON’
WARN_ON(1);
^~~~~~~
drivers/net/ethernet/sfc/mcdi_port.c:345:2: note: here
case MC_CMD_FCNTL_OFF:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <[email protected]>
Acked-by: Edward Cree <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The devlink health reporters create/destroy and user commands currently
use the devlink->lock as a locking mechanism. Different reporters have
different rules in the driver and are being created/destroyed during
different stages of driver load/unload/running. So during execution of a
reporter recover the flow can go through another reporter's destroy and
create. Such flow leads to deadlock trying to lock a mutex already
held.
With the new locking mechanism the different reporters share mutex lock
only to protect access to shared reporters list.
Added refcount per reporter, to protect the reporters from destroy while
being used.
Signed-off-by: Moshe Shemesh <[email protected]>
Signed-off-by: Jiri Pirko <[email protected]>
Acked-by: Jakub Kicinski <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Commit 875f1d0769cd ("iov_iter: add ITER_BVEC_FLAG_NO_REF flag")
introduces one extra flag of ITER_BVEC_FLAG_NO_REF, and this flag
is stored into iter->type.
However, iov_iter_type() doesn't consider the new added flag, fix
it by masking this flag in iov_iter_type().
Fixes: 875f1d0769cd ("iov_iter: add ITER_BVEC_FLAG_NO_REF flag")
Reviewed-by: Christoph Hellwig <[email protected]>
Signed-off-by: Ming Lei <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
Commit 399254aaf489211 ("block: add BIO_NO_PAGE_REF flag") introduces
BIO_NO_PAGE_REF, and once this flag is set for one bio, all pages
in the bio won't be get/put during IO.
However, if one bio is submitted via __blkdev_direct_IO_simple(),
even though BIO_NO_PAGE_REF is set, pages still may be put.
Fixes this issue by avoiding to put pages if BIO_NO_PAGE_REF is
set.
Fixes: 399254aaf489211 ("block: add BIO_NO_PAGE_REF flag")
Reviewed-by: Christoph Hellwig <[email protected]>
Signed-off-by: Ming Lei <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
If we don't end up actually calling submit in io_sq_wq_submit_work(),
we still need to drop the submit reference to the request. If we
don't, then we can leak the request. This can happen if we race
with ring shutdown while flushing the workqueue for requests that
require use of the mm_struct.
Fixes: e65ef56db494 ("io_uring: use regular request ref counts")
Signed-off-by: Jens Axboe <[email protected]>
|
|
If io_allocate_scq_urings() fails to allocate an sq_* region, it will
call io_mem_free() for any previously allocated regions, but leave
dangling pointers to these regions in the ctx. Any regions which have
not yet been allocated are left NULL. Note that when returning
-EOVERFLOW, the previously allocated sq_ring is not freed, which appears
to be an unintentional leak.
When io_allocate_scq_urings() fails, io_uring_create() will call
io_ring_ctx_wait_and_kill(), which calls io_mem_free() on all the sq_*
regions, assuming the pointers are valid and not NULL.
This can result in pages being freed multiple times, which has been
observed to corrupt the page state, leading to subsequent fun. This can
also result in virt_to_page() on NULL, resulting in the use of bogus
page addresses, and yet more subsequent fun. The latter can be detected
with CONFIG_DEBUG_VIRTUAL on arm64.
Adding a cleanup path to io_allocate_scq_urings() complicates the logic,
so let's leave it to io_ring_ctx_free() to consistently free these
pointers, and simplify the io_allocate_scq_urings() error paths.
Full splats from before this patch below. Note that the pointer logged
by the DEBUG_VIRTUAL "non-linear address" warning has been hashed, and
is actually NULL.
[ 26.098129] page:ffff80000e949a00 count:0 mapcount:-128 mapping:0000000000000000 index:0x0
[ 26.102976] flags: 0x63fffc000000()
[ 26.104373] raw: 000063fffc000000 ffff80000e86c188 ffff80000ea3df08 0000000000000000
[ 26.108917] raw: 0000000000000000 0000000000000001 00000000ffffff7f 0000000000000000
[ 26.137235] page dumped because: VM_BUG_ON_PAGE(page_ref_count(page) == 0)
[ 26.143960] ------------[ cut here ]------------
[ 26.146020] kernel BUG at include/linux/mm.h:547!
[ 26.147586] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
[ 26.149163] Modules linked in:
[ 26.150287] Process syz-executor.21 (pid: 20204, stack limit = 0x000000000e9cefeb)
[ 26.153307] CPU: 2 PID: 20204 Comm: syz-executor.21 Not tainted 5.1.0-rc7-00004-g7d30b2ea43d6 #18
[ 26.156566] Hardware name: linux,dummy-virt (DT)
[ 26.158089] pstate: 40400005 (nZcv daif +PAN -UAO)
[ 26.159869] pc : io_mem_free+0x9c/0xa8
[ 26.161436] lr : io_mem_free+0x9c/0xa8
[ 26.162720] sp : ffff000013003d60
[ 26.164048] x29: ffff000013003d60 x28: ffff800025048040
[ 26.165804] x27: 0000000000000000 x26: ffff800025048040
[ 26.167352] x25: 00000000000000c0 x24: ffff0000112c2820
[ 26.169682] x23: 0000000000000000 x22: 0000000020000080
[ 26.171899] x21: ffff80002143b418 x20: ffff80002143b400
[ 26.174236] x19: ffff80002143b280 x18: 0000000000000000
[ 26.176607] x17: 0000000000000000 x16: 0000000000000000
[ 26.178997] x15: 0000000000000000 x14: 0000000000000000
[ 26.181508] x13: 00009178a5e077b2 x12: 0000000000000001
[ 26.183863] x11: 0000000000000000 x10: 0000000000000980
[ 26.186437] x9 : ffff000013003a80 x8 : ffff800025048a20
[ 26.189006] x7 : ffff8000250481c0 x6 : ffff80002ffe9118
[ 26.191359] x5 : ffff80002ffe9118 x4 : 0000000000000000
[ 26.193863] x3 : ffff80002ffefe98 x2 : 44c06ddd107d1f00
[ 26.196642] x1 : 0000000000000000 x0 : 000000000000003e
[ 26.198892] Call trace:
[ 26.199893] io_mem_free+0x9c/0xa8
[ 26.201155] io_ring_ctx_wait_and_kill+0xec/0x180
[ 26.202688] io_uring_setup+0x6c4/0x6f0
[ 26.204091] __arm64_sys_io_uring_setup+0x18/0x20
[ 26.205576] el0_svc_common.constprop.0+0x7c/0xe8
[ 26.207186] el0_svc_handler+0x28/0x78
[ 26.208389] el0_svc+0x8/0xc
[ 26.209408] Code: aa0203e0 d0006861 9133a021 97fcdc3c (d4210000)
[ 26.211995] ---[ end trace bdb81cd43a21e50d ]---
[ 81.770626] ------------[ cut here ]------------
[ 81.825015] virt_to_phys used for non-linear address: 000000000d42f2c7 ( (null))
[ 81.827860] WARNING: CPU: 1 PID: 30171 at arch/arm64/mm/physaddr.c:15 __virt_to_phys+0x48/0x68
[ 81.831202] Modules linked in:
[ 81.832212] CPU: 1 PID: 30171 Comm: syz-executor.20 Not tainted 5.1.0-rc7-00004-g7d30b2ea43d6 #19
[ 81.835616] Hardware name: linux,dummy-virt (DT)
[ 81.836863] pstate: 60400005 (nZCv daif +PAN -UAO)
[ 81.838727] pc : __virt_to_phys+0x48/0x68
[ 81.840572] lr : __virt_to_phys+0x48/0x68
[ 81.842264] sp : ffff80002cf67c70
[ 81.843858] x29: ffff80002cf67c70 x28: ffff800014358e18
[ 81.846463] x27: 0000000000000000 x26: 0000000020000080
[ 81.849148] x25: 0000000000000000 x24: ffff80001bb01f40
[ 81.851986] x23: ffff200011db06c8 x22: ffff2000127e3c60
[ 81.854351] x21: ffff800014358cc0 x20: ffff800014358d98
[ 81.856711] x19: 0000000000000000 x18: 0000000000000000
[ 81.859132] x17: 0000000000000000 x16: 0000000000000000
[ 81.861586] x15: 0000000000000000 x14: 0000000000000000
[ 81.863905] x13: 0000000000000000 x12: ffff1000037603e9
[ 81.866226] x11: 1ffff000037603e8 x10: 0000000000000980
[ 81.868776] x9 : ffff80002cf67840 x8 : ffff80001bb02920
[ 81.873272] x7 : ffff1000037603e9 x6 : ffff80001bb01f47
[ 81.875266] x5 : ffff1000037603e9 x4 : dfff200000000000
[ 81.876875] x3 : ffff200010087528 x2 : ffff1000059ecf58
[ 81.878751] x1 : 44c06ddd107d1f00 x0 : 0000000000000000
[ 81.880453] Call trace:
[ 81.881164] __virt_to_phys+0x48/0x68
[ 81.882919] io_mem_free+0x18/0x110
[ 81.886585] io_ring_ctx_wait_and_kill+0x13c/0x1f0
[ 81.891212] io_uring_setup+0xa60/0xad0
[ 81.892881] __arm64_sys_io_uring_setup+0x2c/0x38
[ 81.894398] el0_svc_common.constprop.0+0xac/0x150
[ 81.896306] el0_svc_handler+0x34/0x88
[ 81.897744] el0_svc+0x8/0xc
[ 81.898715] ---[ end trace b4a703802243cbba ]---
Fixes: 2b188cc1bb857a9d ("Add io_uring IO interface")
Signed-off-by: Mark Rutland <[email protected]>
Cc: Jens Axboe <[email protected]>
Cc: Alexander Viro <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Signed-off-by: Jens Axboe <[email protected]>
|
|
In io_sq_offload_start(), we call cpu_possible() on an unbounded cpu
value from userspace. On v5.1-rc7 on arm64 with
CONFIG_DEBUG_PER_CPU_MAPS, this results in a splat:
WARNING: CPU: 1 PID: 27601 at include/linux/cpumask.h:121 cpu_max_bits_warn include/linux/cpumask.h:121 [inline]
There was an attempt to fix this in commit:
917257daa0fea7a0 ("io_uring: only test SQPOLL cpu after we've verified it")
... by adding a check after the cpu value had been limited to NR_CPU_IDS
using array_index_nospec(). However, this left an unbound check at the
start of the function, for which the warning still fires.
Let's fix this correctly by checking that the cpu value is bound by
nr_cpu_ids before passing it to cpu_possible(). Note that only
nr_cpu_ids of a cpumask are guaranteed to exist at runtime, and
nr_cpu_ids can be significantly smaller than NR_CPUs. For example, an
arm64 defconfig has NR_CPUS=256, while my test VM has 4 vCPUs.
Following the intent from the commit message for 917257daa0fea7a0, the
check is moved under the SQ_AFF branch, which is the only branch where
the cpu values is consumed. The check is performed before bounding the
value with array_index_nospec() so that we don't silently accept bogus
cpu values from userspace, where array_index_nospec() would force these
values to 0.
I suspect we can remove the array_index_nospec() call entirely, but I've
conservatively left that in place, updated to use nr_cpu_ids to match
the prior check.
Tested on arm64 with the Syzkaller reproducer:
https://syzkaller.appspot.com/bug?extid=cd714a07c6de2bc34293
https://syzkaller.appspot.com/x/repro.syz?x=15d8b397200000
Full splat from before this patch:
WARNING: CPU: 1 PID: 27601 at include/linux/cpumask.h:121 cpu_max_bits_warn include/linux/cpumask.h:121 [inline]
WARNING: CPU: 1 PID: 27601 at include/linux/cpumask.h:121 cpumask_check include/linux/cpumask.h:128 [inline]
WARNING: CPU: 1 PID: 27601 at include/linux/cpumask.h:121 cpumask_test_cpu include/linux/cpumask.h:344 [inline]
WARNING: CPU: 1 PID: 27601 at include/linux/cpumask.h:121 io_sq_offload_start fs/io_uring.c:2244 [inline]
WARNING: CPU: 1 PID: 27601 at include/linux/cpumask.h:121 io_uring_create fs/io_uring.c:2864 [inline]
WARNING: CPU: 1 PID: 27601 at include/linux/cpumask.h:121 io_uring_setup+0x1108/0x15a0 fs/io_uring.c:2916
Kernel panic - not syncing: panic_on_warn set ...
CPU: 1 PID: 27601 Comm: syz-executor.0 Not tainted 5.1.0-rc7 #3
Hardware name: linux,dummy-virt (DT)
Call trace:
dump_backtrace+0x0/0x2f0 include/linux/compiler.h:193
show_stack+0x20/0x30 arch/arm64/kernel/traps.c:158
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x110/0x190 lib/dump_stack.c:113
panic+0x384/0x68c kernel/panic.c:214
__warn+0x2bc/0x2c0 kernel/panic.c:571
report_bug+0x228/0x2d8 lib/bug.c:186
bug_handler+0xa0/0x1a0 arch/arm64/kernel/traps.c:956
call_break_hook arch/arm64/kernel/debug-monitors.c:301 [inline]
brk_handler+0x1d4/0x388 arch/arm64/kernel/debug-monitors.c:316
do_debug_exception+0x1a0/0x468 arch/arm64/mm/fault.c:831
el1_dbg+0x18/0x8c
cpu_max_bits_warn include/linux/cpumask.h:121 [inline]
cpumask_check include/linux/cpumask.h:128 [inline]
cpumask_test_cpu include/linux/cpumask.h:344 [inline]
io_sq_offload_start fs/io_uring.c:2244 [inline]
io_uring_create fs/io_uring.c:2864 [inline]
io_uring_setup+0x1108/0x15a0 fs/io_uring.c:2916
__do_sys_io_uring_setup fs/io_uring.c:2929 [inline]
__se_sys_io_uring_setup fs/io_uring.c:2926 [inline]
__arm64_sys_io_uring_setup+0x50/0x70 fs/io_uring.c:2926
__invoke_syscall arch/arm64/kernel/syscall.c:35 [inline]
invoke_syscall arch/arm64/kernel/syscall.c:47 [inline]
el0_svc_common.constprop.0+0x148/0x2e0 arch/arm64/kernel/syscall.c:83
el0_svc_handler+0xdc/0x100 arch/arm64/kernel/syscall.c:129
el0_svc+0x8/0xc arch/arm64/kernel/entry.S:948
SMP: stopping secondary CPUs
Dumping ftrace buffer:
(ftrace buffer empty)
Kernel Offset: disabled
CPU features: 0x002,23000438
Memory Limit: none
Rebooting in 1 seconds..
Fixes: 917257daa0fea7a0 ("io_uring: only test SQPOLL cpu after we've verified it")
Signed-off-by: Mark Rutland <[email protected]>
Cc: Jens Axboe <[email protected]>
Cc: Alexander Viro <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Simplied the logic
Signed-off-by: Jens Axboe <[email protected]>
|
|
Igor Russkikh says:
====================
net: atlantic: Aquantia driver updates 2019-04
This patchset contains various improvements:
- Work targeting link up speedups: link interrupt introduced, some other
logic changes to imrove this.
- FW operations securing with mutex
- Counters and statistics logic improved by Dmitry
- read out of chip temperature via hwmon interface implemented by
Yana and Nikita.
v4 changes:
- remove drvinfo_exit noop
- 64bit stats should be readed out sequentially (lsw, then msw)
declare 64bit read ops for that
v3 changes:
- temp ops renamed to phy_temp ops
- mutex commits squashed for better structure
v2 changes:
- use threaded irq for link state handling
- rework hwmon via devm_hwmon_device_register_with_info
Extra comments on review from Andrew:
- direct device name pointer is used in hwmon registration.
This causes hwmon device to derive possible interface name changes
- Will consider sanity checks for firmware mutex lock separately.
Right now there is no single point exsists where such check could
be easily added.
- There is no way now to fetch and configure min/max/crit temperatures
via FW. Will investigate this separately.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
Some device ids were never released and does not exist.
Cleanup these.
Signed-off-by: Nikita Danilov <[email protected]>
Signed-off-by: Igor Russkikh <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
DMA counters are 64 bit and we can fetch that to reduce
counter overflow, espesially on byte counters.
Tested-by: Nikita Danilov <[email protected]>
Signed-off-by: Igor Russkikh <[email protected]>
Signed-off-by: Dmitry Bogdanov <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
aq_nic_update_ndev_stats pushes statistics to ndev->stats from
system interface. This is not always good because it counts packets/bytes
before any of rx filters (including mac filter).
Its better to report the packet/bytes statistics from DMA
counters which gives actual values of data transferred over pci.
System level stats is still available via ethtool.
Signed-off-by: Nikita Danilov <[email protected]>
Signed-off-by: Igor Russkikh <[email protected]>
Signed-off-by: Dmitry Bogdanov <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This improves ethtool -S usage, where stats are now actual
on each request. Before that stats only were updated at service
timer period.
Tested-by: Nikita Danilov <[email protected]>
Signed-off-by: Igor Russkikh <[email protected]>
Signed-off-by: Dmitry Bogdanov <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Service timer callback fetches statistics from FW and that may cause
a long delay in error cases. We also now need to use fw mutex
to prevent concurrent access to FW, thus - extract that logic
from timer callback into the job in the separate work queue.
Signed-off-by: Nikita Danilov <[email protected]>
Signed-off-by: Igor Russkikh <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Some of FW operations could be invoked simultaneously,
from f.e. ethtool context and from service service activity work.
Here we introduce a fw mutex to secure and serialize access
to FW logic.
Signed-off-by: Nikita Danilov <[email protected]>
Signed-off-by: Igor Russkikh <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Typo in msi code. No much impact though.
Signed-off-by: Nikita Danilov <[email protected]>
Signed-off-by: Igor Russkikh <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Improve for better readability
Signed-off-by: Nikita Danilov <[email protected]>
Signed-off-by: Igor Russkikh <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Original code detected link only after 1 sec is passed after up.
Here we replace this with direct service callback which updates
link status immediately
Signed-off-by: Igor Russkikh <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|