| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Add a global flag @have_nbcon_console to identify if any nbcon
consoles are registered. This will be used in follow-up commits
to preserve legacy behavior when no nbcon consoles are registered.
Signed-off-by: John Ogness <[email protected]>
Reviewed-by: Petr Mladek <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Petr Mladek <[email protected]>
|
|
Currently the console lock is used to attempt legacy-type
printing even if there are no legacy or boot consoles registered.
If no such consoles are registered, the console lock does not
need to be taken.
Add tracking of legacy console registration and use it with
boot console tracking to avoid unnecessary code paths, i.e.
do not use the console lock if there are no boot consoles
and no legacy consoles.
Signed-off-by: John Ogness <[email protected]>
Reviewed-by: Petr Mladek <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Petr Mladek <[email protected]>
|
|
Add nbcon_atomic_flush_unsafe() to flush all nbcon consoles
using the write_atomic() callback and allowing unsafe hostile
takeovers. Call this at the end of panic() as a final attempt
to flush any pending messages.
Note that legacy consoles use unsafe methods for flushing
from the beginning of panic (see bust_spinlocks()). Therefore,
systems using both legacy and nbcon consoles may still fail to
see panic messages due to unsafe legacy console usage.
Signed-off-by: John Ogness <[email protected]>
Reviewed-by: Petr Mladek <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Petr Mladek <[email protected]>
|
|
In console_flush_on_panic(), flush the nbcon consoles before
flushing legacy consoles. The legacy write() callbacks are not
fully safe when oops_in_progress is set.
Signed-off-by: John Ogness <[email protected]>
Reviewed-by: Petr Mladek <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Petr Mladek <[email protected]>
|
|
There may be new records that were added while a driver was
holding the nbcon context for non-printing purposes. These
new records must be flushed by the nbcon_device_release()
context because no other context will do it.
If boot consoles are registered, the legacy loop is used
(either direct or per irq_work) to handle the flushing.
Signed-off-by: John Ogness <[email protected]>
Reviewed-by: Petr Mladek <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Petr Mladek <[email protected]>
|
|
If printk has been explicitly deferred or is called from NMI
context, legacy console printing must be deferred to an irq_work
context. Introduce a helper function is_printk_legacy_deferred()
for a CPU to query if it must defer legacy console printing.
In follow-up commits this helper will be needed at other call
sites as well.
Signed-off-by: John Ogness <[email protected]>
Reviewed-by: Petr Mladek <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Petr Mladek <[email protected]>
|
|
Allow nbcon consoles to print messages in the legacy printk()
caller context (printing via unlock) by integrating them into
console_flush_all(). The write_atomic() callback is used for
printing.
Provide nbcon_legacy_emit_next_record(), which acts as the
nbcon variant of console_emit_next_record(). Call this variant
within console_flush_all() for nbcon consoles. Since nbcon
consoles use their own @nbcon_seq variable to track the next
record to print, this also must be appropriately handled in
console_flush_all().
Note that the legacy printing logic uses @handover to detect
handovers for printing all consoles. For nbcon consoles,
handovers/takeovers occur on a per-console basis and thus do
not cause the console_flush_all() loop to abort.
Signed-off-by: John Ogness <[email protected]>
Reviewed-by: Petr Mladek <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Petr Mladek <[email protected]>
|
|
Unfortunately it is not known if a boot console and a regular
(legacy or nbcon) console use the same hardware. For this reason
they must not be allowed to print simultaneously.
For legacy consoles this is not an issue because they are
already synchronized with the boot consoles using the console
lock. However nbcon consoles can be triggered separately.
Add a global flag @have_boot_console to identify if any boot
consoles are registered. This will be used in follow-up commits
to ensure that boot consoles and nbcon consoles cannot print
simultaneously.
Signed-off-by: John Ogness <[email protected]>
Reviewed-by: Petr Mladek <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Petr Mladek <[email protected]>
|
|
Provide nbcon_atomic_flush_pending() to perform flushing of all
registered nbcon consoles using their write_atomic() callback.
Unlike console_flush_all(), nbcon_atomic_flush_pending() will
only flush up through the newest record at the time of the
call. This prevents a CPU from printing unbounded when other
CPUs are adding records. If new records are added while
flushing, it is expected that the dedicated printer threads
will print those records. If the printer thread is not
available (which is always the case at this point in the
rework), nbcon_atomic_flush_pending() _will_ flush all records
in the ringbuffer.
Unlike console_flush_all(), nbcon_atomic_flush_pending() will
fully flush one console before flushing the next. This helps to
guarantee that a block of pending records (such as a stack
trace in an emergency situation) can be printed atomically at
once before releasing console ownership.
nbcon_atomic_flush_pending() is safe in any context because it
uses write_atomic() and acquires with unsafe_takeover disabled.
Co-developed-by: John Ogness <[email protected]>
Signed-off-by: John Ogness <[email protected]>
Signed-off-by: Thomas Gleixner (Intel) <[email protected]>
Reviewed-by: Petr Mladek <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Petr Mladek <[email protected]>
|
|
Add a helper function to use the current state of the CPU to
determine which priority to assign to the printing context.
The EMERGENCY priority handling is added in a follow-up commit.
It will use a per-CPU variable.
Note: nbcon_device_try_acquire(), which is used by console
drivers to acquire the nbcon console for non-printing
activities, is hard-coded to always use NORMAL priority.
Signed-off-by: John Ogness <[email protected]>
Reviewed-by: Petr Mladek <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Petr Mladek <[email protected]>
|
|
The caller of console_is_usable() usually needs @console->flags
for its own checks. Rather than having console_is_usable() read
its own copy, make the caller pass in the @flags. This also
ensures that the caller saw the same @flags value.
Signed-off-by: John Ogness <[email protected]>
Reviewed-by: Petr Mladek <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Petr Mladek <[email protected]>
|
|
The nbcon consoles use a different printing callback. For nbcon
consoles, check for the write_atomic() callback instead of
write().
Signed-off-by: John Ogness <[email protected]>
Reviewed-by: Petr Mladek <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Petr Mladek <[email protected]>
|
|
Move console_is_usable() as-is into internal.h so that it can
be used by nbcon printing functions as well.
Signed-off-by: John Ogness <[email protected]>
Reviewed-by: Petr Mladek <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Petr Mladek <[email protected]>
|
|
The headers kernel.h, serial_core.h, and console.h allow for the
definitions of many types and functions from other headers.
Rather than relying on these as proxy headers, explicitly
include all headers providing needed definitions. Also sort the
list alphabetically to be able to easily detect duplicates.
Suggested-by: Andy Shevchenko <[email protected]>
Signed-off-by: John Ogness <[email protected]>
Reviewed-by: Andy Shevchenko <[email protected]>
Acked-by: Petr Mladek <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Petr Mladek <[email protected]>
|
|
Currently the port->lock wrappers uart_port_lock(),
uart_port_unlock() (and their variants) only lock/unlock
the spin_lock.
If the port is an nbcon console that has implemented the
write_atomic() callback, the wrappers must also acquire/release
the console context and mark the region as unsafe. This allows
general port->lock synchronization to be synchronized against
the nbcon write_atomic() callback.
Note that __uart_port_using_nbcon() relies on the port->lock
being held while a console is added and removed from the
console list (i.e. all uart nbcon drivers *must* take the
port->lock in their device_lock() callbacks).
Signed-off-by: John Ogness <[email protected]>
Acked-by: Greg Kroah-Hartman <[email protected]>
Reviewed-by: Petr Mladek <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Petr Mladek <[email protected]>
|
|
Provide functions nbcon_device_try_acquire() and
nbcon_device_release() which will try to acquire the nbcon
console ownership with NBCON_PRIO_NORMAL and mark it unsafe for
handover/takeover.
These functions are to be used together with the device-specific
locking when performing non-printing activities on the console
device. They will allow synchronization against the
atomic_write() callback which will be serialized, for higher
priority contexts, only by acquiring the console context
ownership.
Pitfalls:
The API requires to be called in a context with migration
disabled because it uses per-CPU variables internally.
The context is set unsafe for a takeover all the time. It
guarantees full serialization against any atomic_write() caller
except for the final flush in panic() which might try an unsafe
takeover.
Signed-off-by: John Ogness <[email protected]>
Reviewed-by: Petr Mladek <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Petr Mladek <[email protected]>
|
|
It was not clear when exactly console_srcu_read_flags() must be
used vs. directly reading @console->flags.
Refactor and clarify that console_srcu_read_flags() is only
needed if the console is registered or the caller is in a
context where the registration status of the console may change
(due to another context).
The function requires the caller holds @console_srcu, which will
ensure that the caller sees an appropriate @flags value for the
registered console and that exit/cleanup routines will not run
if the console is in the process of unregistration.
Signed-off-by: John Ogness <[email protected]>
Reviewed-by: Petr Mladek <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Petr Mladek <[email protected]>
|
|
Introduce uart_port_set_cons() as a wrapper to set @cons of a
uart_port. The wrapper sets @cons under the port lock in order
to prevent @cons from disappearing while another context is
holding the port lock. This is necessary for a follow-up
commit relating to the port lock wrappers, which rely on @cons
not changing between lock and unlock.
Signed-off-by: John Ogness <[email protected]>
Tested-by: Théo Lebrun <[email protected]> # EyeQ5, AMBA-PL011
Acked-by: Greg Kroah-Hartman <[email protected]>
Reviewed-by: Petr Mladek <[email protected]>
Reviewed-by: Ilpo Järvinen <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Petr Mladek <[email protected]>
|
|
It will be necessary at times for the uart nbcon console
drivers to acquire the port lock directly (without the
additional nbcon functionality of the port lock wrappers).
These are special cases such as the implementation of the
device_lock()/device_unlock() callbacks or for internal
port lock wrapper synchronization.
Provide low-level variants __uart_port_lock_irqsave() and
__uart_port_unlock_irqrestore() for this purpose.
Signed-off-by: John Ogness <[email protected]>
Reviewed-by: Petr Mladek <[email protected]>
Acked-by: Greg Kroah-Hartman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Petr Mladek <[email protected]>
|
|
Console drivers typically have to deal with access to the
hardware via user input/output (such as an interactive login
shell) and output of kernel messages via printk() calls.
They use some classic driver-specific locking mechanism in most
situations. But console->write_atomic() callbacks, used by nbcon
consoles, are synchronized only by acquiring the console
context.
The synchronization via the console context ownership is possible
only when the console driver is registered. It is when a
particular device driver is connected with a particular console
driver.
The two synchronization mechanisms must be synchronized between
each other. It is tricky because the console context ownership
is quite special. It might be taken over by a higher priority
context. Also CPU migration must be disabled. The most tricky
part is to (dis)connect these two mechanisms during the console
(un)registration.
Use the driver-specific locking callbacks: device_lock(),
device_unlock(). They allow taking the device-specific lock
while the device is being (un)registered by the related console
driver.
For example, these callbacks lock/unlock the port lock for
serial port drivers.
Note that the driver-specific locking is only needed during
(un)register if it is an nbcon console with the write_atomic()
callback implemented. If write_atomic() is not implemented, the
driver should never attempt to access the hardware without
first acquiring its driver-specific lock.
Signed-off-by: John Ogness <[email protected]>
Reviewed-by: Petr Mladek <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Petr Mladek <[email protected]>
|
|
Console drivers typically must deal with access to the hardware
via user input/output (such as an interactive login shell) and
output of kernel messages via printk() calls. To provide the
necessary synchronization, usually some driver-specific locking
mechanism is used (for example, the port spinlock for uart
serial consoles).
Until now, usage of this driver-specific locking has been hidden
from the printk-subsystem and implemented within the various
console callbacks. However, nbcon consoles would need to use it
even in the generic code.
Add device_lock() and device_unlock() callback which will need
to get implemented by nbcon consoles.
The callbacks will use whatever synchronization mechanism the
driver is using for itself. The minimum requirement is to
prevent CPU migration. It would allow a context friendly
acquiring of nbcon console ownership in non-emergency and
non-panic context.
Signed-off-by: John Ogness <[email protected]>
Reviewed-by: Petr Mladek <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Petr Mladek <[email protected]>
|
|
The write_atomic() callback has special requirements and is
allowed to use special helper functions. Provide detailed
documentation of the callback so that a developer has a
chance of implementing it correctly.
Signed-off-by: John Ogness <[email protected]>
Reviewed-by: Petr Mladek <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Petr Mladek <[email protected]>
|
|
The return value of write_atomic() does not provide any useful
information. On the contrary, it makes things more complicated
for the caller to appropriately deal with the information.
Change write_atomic() to not have a return value. If the
message did not get printed due to loss of ownership, the
caller will notice this on its own. If ownership was not lost,
it will be assumed that the driver successfully printed the
message and the sequence number for that console will be
incremented.
Signed-off-by: John Ogness <[email protected]>
Reviewed-by: Petr Mladek <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Petr Mladek <[email protected]>
|
|
The functions nbcon_owner_matches() and nbcon_waiter_matches()
use a minimal set of data to determine if a context matches.
The existing kerneldoc and comments were not clear enough and
caused the printk folks to re-prove that the functions are
indeed reliable in all cases.
Update and expand the explanations so that it is clear that the
implementations are sufficient for all cases.
Signed-off-by: John Ogness <[email protected]>
Reviewed-by: Petr Mladek <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Petr Mladek <[email protected]>
|
|
Add validation that printk_deferred_enter()/_exit() are called in
non-migration contexts.
Signed-off-by: Sebastian Andrzej Siewior <[email protected]>
Signed-off-by: John Ogness <[email protected]>
Reviewed-by: Petr Mladek <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Petr Mladek <[email protected]>
|
|
If a non-boot console is registering and boot consoles exist,
the consoles are flushed before being unregistered. This allows
the non-boot console to continue where the boot console left
off.
If for whatever reason flushing fails, the lowest seq found from
any of the enabled boot consoles is used. Until now con->seq was
checked. However, if it is an nbcon boot console, the function
nbcon_seq_read() must be used to read seq because con->seq is
not updated for nbcon consoles.
Check if it is an nbcon boot console and if so call
nbcon_seq_read() to read seq.
Also, avoid usage of con->seq as temporary storage of the
starting record. Instead, rename console_init_seq() to
get_init_console_seq() and just return the value. For nbcon
consoles set the sequence via nbcon_seq_force(), for legacy
consoles set con->seq.
The cleaned design should make sure that the value stays and is
set before the console is added to the console list. It also
unifies the sequence number initialization for legacy and nbcon
consoles.
Reviewed-by: John Ogness <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Petr Mladek <[email protected]>
|
|
Rather than splitting the nbcon allocation and initialization into
two pieces, perform all initialization in nbcon_alloc(). Later,
the initial sequence is calculated and can be explicitly set using
nbcon_seq_force(). This removes the need for the strong rules of
nbcon_init() that even included a BUG_ON().
Signed-off-by: John Ogness <[email protected]>
Reviewed-by: Petr Mladek <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Petr Mladek <[email protected]>
|
|
kernel/printk/printk.c:284:5: sparse: sparse: context imbalance in
'console_srcu_read_lock' - wrong count at exit
include/linux/srcu.h:301:9: sparse: sparse: context imbalance in
'console_srcu_read_unlock' - unexpected unlock
Fixes: 6c4afa79147e ("printk: Prepare for SRCU console list protection")
Signed-off-by: John Ogness <[email protected]>
Reviewed-by: Petr Mladek <[email protected]>
Acked-by: Paul E. McKenney <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Petr Mladek <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux
Pull printk fix from Petr Mladek:
- Do not block printk on non-panic CPUs when they are dumping
backtraces
* tag 'printk-for-6.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux:
printk/panic: Allow cpu backtraces to be written into ringbuffer during panic
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are two driver fixes for regressions from 6.11-rc1 due to the
driver core change making a structure in a driver core callback const.
These were missed by all testing EXCEPT for what Bart happened to be
running, so I appreciate the fixes provided here for some
odd/not-often-used driver subsystems that nothing else happened to
catch.
Both of these fixes have been in linux-next all week with no reported
issues"
* tag 'driver-core-6.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
mips: sgi-ip22: Fix the build
ARM: riscpc: ecard: Fix the build
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc fixes from Greg KH:
"Here are some small char/misc fixes for 6.11-rc4 to resolve reported
problems. Included in here are:
- fastrpc revert of a change that broke userspace
- xillybus fixes for reported issues
Half of these have been in linux-next this week with no reported
problems, I don't know if the last bit of xillybus driver changes made
it in, but they are 'obviously correct' so will be safe :)"
* tag 'char-misc-6.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
char: xillybus: Check USB endpoints when probing device
char: xillybus: Refine workqueue handling
Revert "misc: fastrpc: Restrict untrusted app to attach to privileged PD"
char: xillybus: Don't destroy workqueue from work item running on it
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial fixes from Greg KH:
"Here are some small tty and serial driver fixes for 6.11-rc4 to
resolve some reported problems. Included in here are:
- conmakehash.c userspace build issues
- fsl_lpuart driver fix
- 8250_omap revert for reported regression
- atmel_serial rts flag fix
All of these have been in linux-next this week with no reported
issues"
* tag 'tty-6.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "serial: 8250_omap: Set the console genpd always on if no console suspend"
tty: atmel_serial: use the correct RTS flag.
tty: vt: conmakehash: remove non-portable code printing comment header
tty: serial: fsl_lpuart: mark last busy before uart_add_one_port
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt driver fixes from Greg KH:
"Here are some small USB and Thunderbolt driver fixes for 6.11-rc4 to
resolve some reported issues. Included in here are:
- thunderbolt driver fixes for reported problems
- typec driver fixes
- xhci fixes
- new device id for ljca usb driver
All of these have been in linux-next this week with no reported
issues"
* tag 'usb-6.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
xhci: Fix Panther point NULL pointer deref at full-speed re-enumeration
usb: misc: ljca: Add Lunar Lake ljca GPIO HID to ljca_gpio_hids[]
Revert "usb: typec: tcpm: clear pd_event queue in PORT_RESET"
usb: typec: ucsi: Fix the return value of ucsi_run_command()
usb: xhci: fix duplicate stall handling in handle_tx_event()
usb: xhci: Check for xhci->interrupters being allocated in xhci_mem_clearup()
thunderbolt: Mark XDomain as unplugged when router is removed
thunderbolt: Fix memory leaks in {port|retimer}_sb_regs_write()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull more btrfs fixes from David Sterba:
"A more fixes. We got reports that shrinker added in 6.10 still causes
latency spikes and the fixes don't handle all corner cases. Due to
summer holidays we're taking a shortcut to disable it for release
builds and will fix it in the near future.
- only enable extent map shrinker for DEBUG builds, temporary quick
fix to avoid latency spikes for regular builds
- update target inode's ctime on unlink, mandated by POSIX
- properly take lock to read/update block group's zoned variables
- add counted_by() annotations"
* tag 'for-6.11-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: only enable extent map shrinker for DEBUG builds
btrfs: zoned: properly take lock to read/update block group's zoned variables
btrfs: tree-checker: add dev extent item checks
btrfs: update target inode's ctime on unlink
btrfs: send: annotate struct name_cache_entry with __counted_by()
|
|
fuse_notify_store(), unlike fuse_do_readpage(), does not enable page
zeroing (because it can be used to change partial page contents).
So fuse_notify_store() must be more careful to fully initialize page
contents (including parts of the page that are beyond end-of-file)
before marking the page uptodate.
The current code can leave beyond-EOF page contents uninitialized, which
makes these uninitialized page contents visible to userspace via mmap().
This is an information leak, but only affects systems which do not
enable init-on-alloc (via CONFIG_INIT_ON_ALLOC_DEFAULT_ON=y or the
corresponding kernel command line parameter).
Link: https://bugs.chromium.org/p/project-zero/issues/detail?id=2574
Cc: [email protected]
Fixes: a1d75f258230 ("fuse: add store request")
Signed-off-by: Jann Horn <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"16 hotfixes. All except one are for MM. 10 of these are cc:stable and
the others pertain to post-6.10 issues.
As usual with these merges, singletons and doubletons all over the
place, no identifiable-by-me theme. Please see the lovingly curated
changelogs to get the skinny"
* tag 'mm-hotfixes-stable-2024-08-17-19-34' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
mm/migrate: fix deadlock in migrate_pages_batch() on large folios
alloc_tag: mark pages reserved during CMA activation as not tagged
alloc_tag: introduce clear_page_tag_ref() helper function
crash: fix riscv64 crash memory reserve dead loop
selftests: memfd_secret: don't build memfd_secret test on unsupported arches
mm: fix endless reclaim on machines with unaccepted memory
selftests/mm: compaction_test: fix off by one in check_compaction()
mm/numa: no task_numa_fault() call if PMD is changed
mm/numa: no task_numa_fault() call if PTE is changed
mm/vmalloc: fix page mapping if vm_area_alloc_pages() with high order fallback to order 0
mm/memory-failure: use raw_spinlock_t in struct memory_failure_cpu
mm: don't account memmap per-node
mm: add system wide stats items category
mm: don't account memmap on failure
mm/hugetlb: fix hugetlb vs. core-mm PT locking
mseal: fix is_madv_discard()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix crashes on 85xx with some configs since the recent hugepd rework.
- Fix boot warning with hugepages and CONFIG_DEBUG_VIRTUAL on some
platforms.
- Don't enable offline cores when changing SMT modes, to match existing
userspace behaviour.
Thanks to Christophe Leroy, Dr. David Alan Gilbert, Guenter Roeck, Nysal
Jan K.A, Shrikanth Hegde, Thomas Gleixner, and Tyrel Datwyler.
* tag 'powerpc-6.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/topology: Check if a core is online
cpu/SMT: Enable SMT only if a core is online
powerpc/mm: Fix boot warning with hugepages and CONFIG_DEBUG_VIRTUAL
powerpc/mm: Fix size of allocated PGDIR
soc: fsl: qbman: remove unused struct 'cgr_comp'
|
|
Pull smb client fixes from Steve French:
- fix for clang warning - additional null check
- fix for cached write with posix locks
- flexible structure fix
* tag 'v6.11-rc3-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
smb: smb2pdu.h: Use static_assert() to check struct sizes
smb3: fix lock breakage for cached writes
smb/client: avoid possible NULL dereference in cifs_free_subrequest()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"I2C core fix replacing IS_ENABLED() with IS_REACHABLE()
For host drivers, there are two fixes:
- Tegra I2C Controller: Addresses a potential double-locking issue
during probe. ACPI devices are not IRQ-safe when invoking runtime
suspend and resume functions, so the irq_safe flag should not be
set.
- Qualcomm GENI I2C Controller: Fixes an oversight in the exit path
of the runtime_resume() function, which was missed in the previous
release"
* tag 'i2c-for-6.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: tegra: Do not mark ACPI devices as irq safe
i2c: Use IS_REACHABLE() for substituting empty ACPI functions
i2c: qcom-geni: Add missing geni_icc_disable in geni_i2c_runtime_resume
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two small fixes to the mpi3mr driver. One to avoid oversize
allocations in tracing and the other to fix an uninitialized spinlock
in the user to driver feature request code (used to trigger dumps and
the like)"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: mpi3mr: Avoid MAX_PAGE_ORDER WARNING for buffer allocations
scsi: mpi3mr: Add missing spin_lock_init() for mrioc->trigger_lock
|
|
Pull xfs fixes from Chandan Babu:
- Check for presence of only 'attr' feature before scrubbing an inode's
attribute fork.
- Restore the behaviour of setting AIL thread to TASK_INTERRUPTIBLE for
long (i.e. 50ms) sleep durations to prevent high load averages.
- Do not allow users to change the realtime flag of a file unless the
datadev and rtdev both support fsdax access modes.
* tag 'xfs-6.11-fixes-3' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: conditionally allow FS_XFLAG_REALTIME changes if S_DAX is set
xfs: revert AIL TASK_KILLABLE threshold
xfs: attr forks require attr, not attr2
|
|
Pull bcachefs fixes from Kent OverstreetL
- New on disk format version, bcachefs_metadata_version_disk_accounting_inum
This adds one more disk accounting counter, which counts disk usage
and number of extents per inode number. This lets us track
fragmentation, for implementing defragmentation later, and it also
counts disk usage per inode in all snapshots, which will be a useful
thing to expose to users.
- One performance issue we've observed is threads spinning when they
should be waiting for dirty keys in the key cache to be flushed by
journal reclaim, so we now have hysteresis for the waiting thread, as
well as improving the tracepoint and a new time_stat, for tracking
time blocked waiting on key cache flushing.
... and various assorted smaller fixes.
* tag 'bcachefs-2024-08-16' of git://evilpiepirate.org/bcachefs:
bcachefs: Fix locking in __bch2_trans_mark_dev_sb()
bcachefs: fix incorrect i_state usage
bcachefs: avoid overflowing LRU_TIME_BITS for cached data lru
bcachefs: Fix forgetting to pass trans to fsck_err()
bcachefs: Increase size of cuckoo hash table on too many rehashes
bcachefs: bcachefs_metadata_version_disk_accounting_inum
bcachefs: Kill __bch2_accounting_mem_mod()
bcachefs: Make bkey_fsck_err() a wrapper around fsck_err()
bcachefs: Fix warning in __bch2_fsck_err() for trans not passed in
bcachefs: Add a time_stat for blocked on key cache flush
bcachefs: Improve trans_blocked_journal_reclaim tracepoint
bcachefs: Add hysteresis to waiting on btree key cache flush
lib/generic-radix-tree.c: Fix rare race in __genradix_ptr_alloc()
bcachefs: Convert for_each_btree_node() to lockrestart_do()
bcachefs: Add missing downgrade table entry
bcachefs: disk accounting: ignore unknown types
bcachefs: bch2_accounting_invalid() fixup
bcachefs: Fix bch2_trigger_alloc when upgrading from old versions
bcachefs: delete faulty fastpath in bch2_btree_path_traverse_cached()
|
|
We run this in full RW mode now, so we have to guard against the
superblock buffer being reallocated.
Signed-off-by: Kent Overstreet <[email protected]>
|
|
Pull memcg-v1 fix from Al Viro:
"memcg_write_event_control() oops fix"
* tag 'pull-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
memcg_write_event_control(): fix a user-triggerable oops
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Fix the arm64 __get_mem_asm() to use the _ASM_EXTABLE_##type##ACCESS()
macro instead of the *_ERR() one in order to avoid writing -EFAULT to
the value register in case of a fault
- Initialise all elements of the acpi_early_node_map[] to NUMA_NO_NODE.
Prior to this fix, only the first element was initialised
- Move the KASAN random tag seed initialisation after the per-CPU areas
have been initialised (prng_state is __percpu)
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Fix KASAN random tag seed initialization
arm64: ACPI: NUMA: initialize all values of acpi_early_node_map to NUMA_NO_NODE
arm64: uaccess: correct thinko in __get_mem_asm()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fix from Stephen Boyd:
"One fix for the new T-Head TH1520 clk driver that marks a bus clk
critical so that it isn't turned off during late init which breaks
emmc-sdio"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: thead: fix dependency on clk_ignore_unused
|
|
Pull block fixes from Jens Axboe:
- Fix corruption issues with s390/dasd (Eric, Stefan)
- Fix a misuse of non irq locking grab of a lock (Li)
- MD pull request with a single data corruption fix for raid1 (Yu)
* tag 'block-6.11-20240824' of git://git.kernel.dk/linux:
block: Fix lockdep warning in blk_mq_mark_tag_wait
md/raid1: Fix data corruption for degraded array with slow disk
s390/dasd: fix error recovery leading to data corruption on ESE devices
s390/dasd: Remove DMA alignment
|
|
Pull io_uring fixes from Jens Axboe:
- Fix a comment in the uapi header using the wrong member name (Caleb)
- Fix KCSAN warning for a debug check in sqpoll (me)
- Two more NAPI tweaks (Olivier)
* tag 'io_uring-6.11-20240824' of git://git.kernel.dk/linux:
io_uring: fix user_data field name in comment
io_uring/sqpoll: annotate debug task == current with data_race()
io_uring/napi: remove duplicate io_napi_entry timeout assignation
io_uring/napi: check napi_enabled in io_napi_add() before proceeding
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
- Fix a possible (but unlikely) out-of-bounds read in interrupts
parsing code
- Add AT25 EEPROM "fujitsu,mb85rs256" compatible
- Update Konrad Dybcio's email
* tag 'devicetree-fixes-for-6.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of/irq: Prevent device address out-of-bounds read in interrupt map walk
dt-bindings: eeprom: at25: add fujitsu,mb85rs256 compatible
dt-bindings: Batch-update Konrad Dybcio's email
|