| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
vmscan/mm_vmscan_lru_isolate
When using trace-vmscan-postprocess.pl for checking the file/anon rate
of scanning, we can find that it can not be performed. At the same
time, the following message will be reported:
WARNING: Format not as expected for event vmscan/mm_vmscan_lru_isolate
'file' != 'contig_taken' Fewer fields than expected in format at
./trace-vmscan-postprocess.pl line 171, <FORMAT> line 76.
In trace-vmscan-postprocess.pl, (contig_taken, contig_dirty, and
contig_failed) are be associated respectively to (nr_lumpy_taken,
nr_lumpy_dirty, and nr_lumpy_failed) for lumpy reclaim. Via commit
c53919adc045 ("mm: vmscan: remove lumpy reclaim"), lumpy reclaim had
already been removed by Mel, but the update for
trace-vmscan-postprocess.pl was missed.
Signed-off-by: Chen Yucong <[email protected]>
Cc: Mel Gorman <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Fix a regression caused by 7fc34a62ca44 ("mm/msync.c: sync only the
requested range in msync()").
xfstests generic/075 fail occured on ext4 data=journal mode because the
intended range was not syncing due to wrong fstart calculation.
Signed-off-by: Namjae Jeon <[email protected]>
Signed-off-by: Ashish Sangwan <[email protected]>
Reported-by: Eric Whitney <[email protected]>
Tested-by: Eric Whitney <[email protected]>
Acked-by: Matthew Wilcox <[email protected]>
Reviewed-by: Lukas Czerner <[email protected]>
Tested-by: Lukas Czerner <[email protected]>
Reviewed-by: Theodore Ts'o <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Alexander reported mkswap on /dev/zram0 is failed if other process is
opening the block device file.
Step is as follows,
0. Reset the unused zram device.
1. Use a program that opens /dev/zram0 with O_RDWR and sleeps
until killed.
2. While that program sleeps, echo the correct value to
/sys/block/zram0/disksize.
3. Verify (e.g. in /proc/partitions) that the disk size is applied
correctly. It is.
4. While that program still sleeps, attempt to mkswap /dev/zram0.
This fails: mkswap: error: swap area needs to be at least 40 KiB
When I investigated, the size get by ioctl(fd, BLKGETSIZE64, xxx) on
mkswap to get a size of blockdev was zero although zram0 has right size by
2.
The reason is zram didn't revalidate disk after changing capacity so that
size of blockdev's inode is not uptodate until all of file is close.
This patch should fix the BUG.
Signed-off-by: Minchan Kim <[email protected]>
Reported-by: Alexander E. Patrakov <[email protected]>
Tested-by: Alexander E. Patrakov <[email protected]>
Reviewed-by: Sergey Senozhatsky <[email protected]>
Cc: Nitin Gupta <[email protected]>
Acked-by: Jerome Marchand <[email protected]>
Cc: <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
on-off-test uses "$UID != 0" to test for root, but $UID is a construct
specific to bash. Using /bin/sh that isn't bash results in the
following error (due to the "$UID" part expanding to nothing):
./on-off-test.sh: 9: [: !=: unexpected operator
Change Makefile to use bash instead.
Signed-off-by: Shuah Khan <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
on-off-test uses "$UID != 0" to test for root, but $UID is a construct
specific to bash. Using /bin/sh that isn't bash results in the
following error (due to the "$UID" part expanding to nothing):
./on-off-test.sh: 9: [: !=: unexpected operator
Change Makefile to use bash instead.
Signed-off-by: Shuah Khan <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
On strict build environments we can see:
fs/autofs4/inode.c: In function 'autofs4_fill_super':
fs/autofs4/inode.c:312: error: 'pgrp' may be used uninitialized in this function
make[2]: *** [fs/autofs4/inode.o] Error 1
make[1]: *** [fs/autofs4] Error 2
make: *** [fs] Error 2
make: *** Waiting for unfinished jobs....
This is due to the use of pgrp_set being used to indicate pgrp has has
been set rather than initializing pgrp itself.
Signed-off-by: Ian Kent <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
min_partial means minimum number of slab cached in node partial list.
So, if nr_partial is less than it, we keep newly empty slab on node
partial list rather than freeing it. But if nr_partial is equal or
greater than it, it means that we have enough partial slabs so should
free newly empty slab. Current implementation missed the equal case so
if we set min_partial is 0, then, at least one slab could be cached.
This is critical problem to kmemcg destroying logic because it doesn't
works properly if some slabs is cached. This patch fixes this problem.
Fixes 91cb69620284 ("slub: make dead memcg caches discard free slabs
immediately").
Signed-off-by: Joonsoo Kim <[email protected]>
Acked-by: Vladimir Davydov <[email protected]>
Cc: Christoph Lameter <[email protected]>
Cc: Pekka Enberg <[email protected]>
Acked-by: David Rientjes <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
With a kernel configured with ARM64_64K_PAGES && !TRANSPARENT_HUGEPAGE,
the following is triggered at early boot:
SMP: Total of 8 processors activated.
devtmpfs: initialized
Unable to handle kernel NULL pointer dereference at virtual address 00000008
pgd = fffffe0000050000
[00000008] *pgd=00000043fba00003, *pmd=00000043fba00003, *pte=00e0000078010407
Internal error: Oops: 96000006 [#1] SMP
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.15.0-rc864k+ #44
task: fffffe03bc040000 ti: fffffe03bc080000 task.ti: fffffe03bc080000
PC is at __list_add+0x10/0xd4
LR is at free_one_page+0x270/0x638
...
Call trace:
__list_add+0x10/0xd4
free_one_page+0x26c/0x638
__free_pages_ok.part.52+0x84/0xbc
__free_pages+0x74/0xbc
init_cma_reserved_pageblock+0xe8/0x104
cma_init_reserved_areas+0x190/0x1e4
do_one_initcall+0xc4/0x154
kernel_init_freeable+0x204/0x2a8
kernel_init+0xc/0xd4
This happens because init_cma_reserved_pageblock() calls
__free_one_page() with pageblock_order as page order but it is bigger
than MAX_ORDER. This in turn causes accesses past zone->free_list[].
Fix the problem by changing init_cma_reserved_pageblock() such that it
splits pageblock into individual MAX_ORDER pages if pageblock is bigger
than a MAX_ORDER page.
In cases where !CONFIG_HUGETLB_PAGE_SIZE_VARIABLE, which is all
architectures expect for ia64, powerpc and tile at the moment, the
âpageblock_order > MAX_ORDERâ condition will be optimised out since both
sides of the operator are constants. In cases where pageblock size is
variable, the performance degradation should not be significant anyway
since init_cma_reserved_pageblock() is called only at boot time at most
MAX_CMA_AREAS times which by default is eight.
Signed-off-by: Michal Nazarewicz <[email protected]>
Reported-by: Mark Salter <[email protected]>
Tested-by: Mark Salter <[email protected]>
Tested-by: Christopher Covington <[email protected]>
Cc: Mel Gorman <[email protected]>
Cc: David Rientjes <[email protected]>
Cc: Marek Szyprowski <[email protected]>
Cc: Catalin Marinas <[email protected]>
Cc: <[email protected]> [3.5+]
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Often when starting a transaction we commit the currently running transaction,
which can end up writing block group caches when the current process has its
journal_info set to NULL (and not to a transaction). This makes our assertion
at btrfs_check_data_free_space() (current_journal != NULL) fail, resulting
in a crash/hang. Therefore fix it by setting journal_info.
Two different traces of this issue follow below.
1)
[51502.241936] BTRFS: assertion failed: current->journal_info, file: fs/btrfs/extent-tree.c, line: 3670
[51502.242213] ------------[ cut here ]------------
[51502.242493] kernel BUG at fs/btrfs/ctree.h:3964!
[51502.242669] invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC
(...)
[51502.244010] Call Trace:
[51502.244010] [<ffffffffa02bc025>] btrfs_check_data_free_space+0x395/0x3a0 [btrfs]
[51502.244010] [<ffffffffa02c3bdc>] btrfs_write_dirty_block_groups+0x4ac/0x640 [btrfs]
[51502.244010] [<ffffffffa0357a6a>] commit_cowonly_roots+0x164/0x226 [btrfs]
[51502.244010] [<ffffffffa02d53cd>] btrfs_commit_transaction+0x4ed/0xab0 [btrfs]
[51502.244010] [<ffffffff8168ec7b>] ? _raw_spin_unlock+0x2b/0x40
[51502.244010] [<ffffffffa02d6259>] start_transaction+0x459/0x620 [btrfs]
[51502.244010] [<ffffffffa02d67ab>] btrfs_start_transaction+0x1b/0x20 [btrfs]
[51502.244010] [<ffffffffa02d73e1>] __unlink_start_trans+0x31/0xe0 [btrfs]
[51502.244010] [<ffffffffa02dea67>] btrfs_unlink+0x37/0xc0 [btrfs]
[51502.244010] [<ffffffff811bb054>] ? do_unlinkat+0x114/0x2a0
[51502.244010] [<ffffffff811baebc>] vfs_unlink+0xcc/0x150
[51502.244010] [<ffffffff811bb1a0>] do_unlinkat+0x260/0x2a0
[51502.244010] [<ffffffff811a9ef4>] ? filp_close+0x64/0x90
[51502.244010] [<ffffffff810aaea6>] ? trace_hardirqs_on_caller+0x16/0x1e0
[51502.244010] [<ffffffff81349cab>] ? trace_hardirqs_on_thunk+0x3a/0x3f
[51502.244010] [<ffffffff811be9eb>] SyS_unlinkat+0x1b/0x40
[51502.244010] [<ffffffff81698452>] system_call_fastpath+0x16/0x1b
[51502.244010] Code: 0b 55 48 89 e5 0f 0b 55 48 89 e5 0f 0b 55 89 f1 48 c7 c2 71 13 36 a0 48 89 fe 31 c0 48 c7 c7 b8 43 36 a0 48 89 e5 e8 5d b0 32 e1 <0f> 0b 0f 1f 44 00 00 55 b9 11 00 00 00 48 89 e5 41 55 49 89 f5
[51502.244010] RIP [<ffffffffa03575da>] assfail.constprop.88+0x1e/0x20 [btrfs]
2)
[25405.097230] BTRFS: assertion failed: current->journal_info, file: fs/btrfs/extent-tree.c, line: 3670
[25405.097488] ------------[ cut here ]------------
[25405.097767] kernel BUG at fs/btrfs/ctree.h:3964!
[25405.097940] invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC
(...)
[25405.100008] Call Trace:
[25405.100008] [<ffffffffa02bc025>] btrfs_check_data_free_space+0x395/0x3a0 [btrfs]
[25405.100008] [<ffffffffa02c3bdc>] btrfs_write_dirty_block_groups+0x4ac/0x640 [btrfs]
[25405.100008] [<ffffffffa035755a>] commit_cowonly_roots+0x164/0x226 [btrfs]
[25405.100008] [<ffffffffa02d53cd>] btrfs_commit_transaction+0x4ed/0xab0 [btrfs]
[25405.100008] [<ffffffff8109c170>] ? bit_waitqueue+0xc0/0xc0
[25405.100008] [<ffffffffa02d6259>] start_transaction+0x459/0x620 [btrfs]
[25405.100008] [<ffffffffa02d67ab>] btrfs_start_transaction+0x1b/0x20 [btrfs]
[25405.100008] [<ffffffffa02e3407>] btrfs_create+0x47/0x210 [btrfs]
[25405.100008] [<ffffffffa02d74cc>] ? btrfs_permission+0x3c/0x80 [btrfs]
[25405.100008] [<ffffffff811bc63b>] vfs_create+0x9b/0x130
[25405.100008] [<ffffffff811bcf19>] do_last+0x849/0xe20
[25405.100008] [<ffffffff811b9409>] ? link_path_walk+0x79/0x820
[25405.100008] [<ffffffff811bd5b5>] path_openat+0xc5/0x690
[25405.100008] [<ffffffff810ab07d>] ? trace_hardirqs_on+0xd/0x10
[25405.100008] [<ffffffff811cdcd2>] ? __alloc_fd+0x32/0x1d0
[25405.100008] [<ffffffff811be2a3>] do_filp_open+0x43/0xa0
[25405.100008] [<ffffffff811cddf1>] ? __alloc_fd+0x151/0x1d0
[25405.100008] [<ffffffff811abcfc>] do_sys_open+0x13c/0x230
[25405.100008] [<ffffffff810aaea6>] ? trace_hardirqs_on_caller+0x16/0x1e0
[25405.100008] [<ffffffff811abe12>] SyS_open+0x22/0x30
[25405.100008] [<ffffffff81698452>] system_call_fastpath+0x16/0x1b
[25405.100008] Code: 0b 55 48 89 e5 0f 0b 55 48 89 e5 0f 0b 55 89 f1 48 c7 c2 51 13 36 a0 48 89 fe 31 c0 48 c7 c7 d0 43 36 a0 48 89 e5 e8 6d b5 32 e1 <0f> 0b 0f 1f 44 00 00 55 b9 11 00 00 00 48 89 e5 41 55 49 89 f5
[25405.100008] RIP [<ffffffffa03570ca>] assfail.constprop.88+0x1e/0x20 [btrfs]
Signed-off-by: Filipe David Borba Manana <[email protected]>
Signed-off-by: Chris Mason <[email protected]>
|
|
We wouldn't actuall print the extent information if we had a skinny metadata
item, this fixes that. Thanks,
Signed-off-by: Josef Bacik <[email protected]>
Signed-off-by: Chris Mason <[email protected]>
|
|
This percpu counter @total_bytes_pinned is introduced to skip unnecessary
operations of 'commit transaction', it accounts for those space we may free
but are stuck in delayed refs.
And we zero out @space_info->total_bytes_pinned every transaction period so
we have a better idea of how much space we'll actually free up by committing
this transaction. However, we do the 'zero out' part a little earlier, before
we actually unpin space, so we end up returning ENOSPC when we actually have
free space that's just unpinned from committing transaction.
xfstests/generic/074 complained then.
This fixes it by actually accounting the percpu pinned number when 'unpin',
and since it's protected by space_info->lock, the race is gone now.
Signed-off-by: Liu Bo <[email protected]>
Reviewed-by: Miao Xie <[email protected]>
Signed-off-by: Chris Mason <[email protected]>
|
|
Return codes got updated in 60e1975acb48fc3d74a3422b21dde74c977ac3d5
(btrfs: return errno instead of -1 from compression)
lzo wrapper returns E2BIG in this case, do the same for zlib.
Signed-off-by: David Sterba <[email protected]>
|
|
Commit fcebe4562dec83b3f8d3088d77584727b09130b2 (Btrfs: rework qgroup
accounting) removed the qgroup accounting after delayed refs.
Signed-off-by: David Sterba <[email protected]>
|
|
The transaction handle was being used after being freed.
Cc: Chris Mason <[email protected]>
Signed-off-by: Filipe David Borba Manana <[email protected]>
Signed-off-by: Chris Mason <[email protected]>
|
|
dev->name is null but missing flag is not set.
Strictly speaking the missing flag should have been set, but there
are more places where code just checks if name is null. For now this
patch does the same.
stack:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000064
IP: [<ffffffffa0228908>] btrfs_show_devname+0x58/0xf0 [btrfs]
[<ffffffff81198879>] show_vfsmnt+0x39/0x130
[<ffffffff81178056>] m_show+0x16/0x20
[<ffffffff8117d706>] seq_read+0x296/0x390
[<ffffffff8115aa7d>] vfs_read+0x9d/0x160
[<ffffffff8115b549>] SyS_read+0x49/0x90
[<ffffffff817abe52>] system_call_fastpath+0x16/0x1b
reproducer:
mkfs.btrfs -draid1 -mraid1 /dev/sdg1 /dev/sdg2
btrfstune -S 1 /dev/sdg1
modprobe -r btrfs && modprobe btrfs
mount -o degraded /dev/sdg1 /btrfs
btrfs dev add /dev/sdg3 /btrfs
Signed-off-by: Anand Jain <[email protected]>
Signed-off-by: Chris Mason <[email protected]>
|
|
when one of the device path is missing btrfs_device name is null. So this
patch will check for that.
stack:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000010
IP: [<ffffffff812e18c0>] strlen+0x0/0x30
[<ffffffffa01cd92a>] ? clone_fs_devices+0xaa/0x160 [btrfs]
[<ffffffffa01cdcf7>] btrfs_init_new_device+0x317/0xca0 [btrfs]
[<ffffffff81155bca>] ? __kmalloc_track_caller+0x15a/0x1a0
[<ffffffffa01d6473>] btrfs_ioctl+0xaa3/0x2860 [btrfs]
[<ffffffff81132a6c>] ? handle_mm_fault+0x48c/0x9c0
[<ffffffff81192a61>] ? __blkdev_put+0x171/0x180
[<ffffffff817a784c>] ? __do_page_fault+0x4ac/0x590
[<ffffffff81193426>] ? blkdev_put+0x106/0x110
[<ffffffff81179175>] ? mntput+0x35/0x40
[<ffffffff8116d4b0>] do_vfs_ioctl+0x460/0x4a0
[<ffffffff8115c72e>] ? ____fput+0xe/0x10
[<ffffffff81068033>] ? task_work_run+0xb3/0xd0
[<ffffffff8116d547>] SyS_ioctl+0x57/0x90
[<ffffffff817a793e>] ? do_page_fault+0xe/0x10
[<ffffffff817abe52>] system_call_fastpath+0x16/0x1b
reproducer:
mkfs.btrfs -draid1 -mraid1 /dev/sdg1 /dev/sdg2
btrfstune -S 1 /dev/sdg1
modprobe -r btrfs && modprobe btrfs
mount -o degraded /dev/sdg1 /btrfs
btrfs dev add /dev/sdg3 /btrfs
Signed-off-by: Anand Jain <[email protected]>
Signed-off-by: Chris Mason <[email protected]>
|
|
The commit
0780253 btrfs: Cleanup the btrfs_parse_options for remount.
broke ssd options quite badly; it stopped making ssd_spread
imply ssd, and it made "nossd" unsettable.
Put things back at least as well as they were before
(though ssd mount option handling is still pretty odd:
# mount -o "nossd,ssd_spread" works?)
Reported-by: Roman Mamedov <[email protected]>
Signed-off-by: Eric Sandeen <[email protected]>
Signed-off-by: Chris Mason <[email protected]>
|
|
Balance recovery is called when RW mounting or remounting from
RO to RW, it is called to finish roots merging.
When doing balance recovery, relocation root's corresponding
fs root(whose root refs is 0) might be destroyed by cleaner
thread, this will make btrfs fail to mount.
Fix this problem by holding @cleaner_mutex when doing balance
recovery.
Signed-off-by: Wang Shilong <[email protected]>
Signed-off-by: Chris Mason <[email protected]>
|
|
This change is based on the corresponding recent change for ext4:
ext4: atomically set inode->i_flags in ext4_set_inode_flags()
That has the following commit message that applies to btrfs as well:
"Use cmpxchg() to atomically set i_flags instead of clearing out the
S_IMMUTABLE, S_APPEND, etc. flags and then setting them from the
EXT4_IMMUTABLE_FL, EXT4_APPEND_FL flags, since this opens up a race
where an immutable file has the immutable flag cleared for a brief
window of time."
Replacing EXT4_IMMUTABLE_FL and EXT4_APPEND_FL with BTRFS_INODE_IMMUTABLE
and BTRFS_INODE_APPEND, respectively.
Reviewed-by: David Sterba <[email protected]>
Reviewed-by: Satoru Takeuchi <[email protected]>
Signed-off-by: Filipe David Borba Manana <[email protected]>
Signed-off-by: Chris Mason <[email protected]>
|
|
With commit 9da0763b (kbuild: Use relative path when building in a
subdir of the source tree), the compiler messages include relative
paths. These are however relative to the build directory, not the
directory where make was started. Print the "Entering directory ..."
message once, so that IDEs/editors can find the source files.
Acked-by: David Howells <[email protected]>
Signed-off-by: Michal Marek <[email protected]>
|
|
Commit "drm/vmwgfx: correct fb_fix_screeninfo.line_length", while fixing a
vmwgfx fbdev bug, also writes the pitch to a supposedly read-only register:
SVGA_REG_BYTES_PER_LINE, while it should be (and also in fact is) written to
SVGA_REG_PITCHLOCK.
This patch is Cc'd stable because of the unknown effects writing to this
register might have, particularly on older device versions.
v2: Updated log message.
Cc: [email protected]
Cc: Christopher Friedt <[email protected]>
Tested-by: Christopher Friedt <[email protected]>
Signed-off-by: Thomas Hellstrom <[email protected]>
Reviewed-by: Jakob Bornecrantz <[email protected]>
|
|
When we write to a degraded array which has a bitmap, we
make sure the relevant bit in the bitmap remains set when
the write completes (so a 're-add' can quickly rebuilt a
temporarily-missing device).
If, immediately after such a write starts, we incorporate a spare,
commence recovery, and skip over the region where the write is
happening (because the 'needs recovery' flag isn't set yet),
then that write will not get to the new device.
Once the recovery finishes the new device will be trusted, but will
have incorrect data, leading to possible corruption.
We cannot set the 'needs recovery' flag when we start the write as we
do not know easily if the write will be "degraded" or not. That
depends on details of the particular raid level and particular write
request.
This patch fixes a corruption issue of long standing and so it
suitable for any -stable kernel. It applied correctly to 3.0 at
least and will minor editing to earlier kernels.
Reported-by: Bill <[email protected]>
Tested-by: Bill <[email protected]>
Cc: [email protected]
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: NeilBrown <[email protected]>
|
|
If an array has a bitmap, the when we set the "has bitmap" flag we
incorrectly clear the "is clean" flag.
"is clean" isn't really important when a bitmap is present, but it is
best to get it right anyway.
Reported-by: George Duffield <[email protected]>
Link: http://lkml.kernel.org/CAG__1a4MRV6gJL38XLAurtoSiD3rLBTmWpcS5HYvPpSfPR88UQ@mail.gmail.com
Fixes: 36fa30636fb84b209210299684e1be66d9e58217 (v2.6.14)
Signed-off-by: NeilBrown <[email protected]>
|
|
misc fixes, output fixes for 4k monitor, dpm lockup fixes
* 'drm-fixes-3.16' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: page table BOs are kernel allocations
drm/radeon/cik: fix typo in EOP packet
drm/radeon: Track the status of a page flip more explicitly
drm/radeon/dpm: fix vddci setup typo on cayman
drm/radeon/dpm: fix typo in vddci setup for eg/btc
drm/radeon: use RADEON_MAX_CRTCS, RADEON_MAX_AFMT_BLOCKS (v2)
drm/radeon: Use only one line for whole DPCD debug output
drm/radeon: add a module parameter to control deep color support
drm/radeon: enable bapm by default on desktop TN/RL boards
drm/radeon: enable bapm by default on KV/KB
drm/radeon: only apply bapm changes for AC power on ARUBA
drm/radeon: adjust default dispclk on DCE6 (v2)
|
|
1539fb9bd405ee32282ea0a38404f9e008ac5b7a managed to somehow +x
drm_drv.c undo it.
Signed-off-by: Dave Airlie <[email protected]>
|
|
XDR requires 4-byte alignment; nfs4d READLINK reply writes out the padding,
but truncates the packet to the padding-less size.
Fix by taking the padding into consideration when truncating the packet.
Symptoms:
# ll /mnt/
ls: cannot read symbolic link /mnt/test: Input/output error
total 4
-rw-r--r--. 1 root root 0 Jun 14 01:21 123456
lrwxrwxrwx. 1 root root 6 Jul 2 03:33 test
drwxr-xr-x. 1 root root 0 Jul 2 23:50 tmp
drwxr-xr-x. 1 root root 60 Jul 2 23:44 tree
Signed-off-by: Avi Kivity <[email protected]>
Fixes: 476a7b1f4b2c (nfsd4: don't treat readlink like a zero-copy operation)
Reviewed-by: Kinglong Mee <[email protected]>
Signed-off-by: J. Bruce Fields <[email protected]>
|
|
Userspace shouldn't be able to access them.
Signed-off-by: Christian König <[email protected]>
Cc: [email protected]
Signed-off-by: Alex Deucher <[email protected]>
|
|
Volatile bit was in the wrong location. This bit is
not used at the moment.
Signed-off-by: Alex Deucher <[email protected]>
Cc: [email protected]
|
|
d911d9874801 ("kernfs: make kernfs_notify() trigger inotify events
too") added fsnotify triggering to kernfs_notify() which requires a
sleepable context. There are already existing users of
kernfs_notify() which invoke it from an atomic context and in general
it's silly to require a sleepable context for triggering a
notification.
The following is an invalid context bug triggerd by md invoking
sysfs_notify() from IO completion path.
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:586
in_atomic(): 1, irqs_disabled(): 1, pid: 0, name: swapper/1
2 locks held by swapper/1/0:
#0: (&(&vblk->vq_lock)->rlock){-.-...}, at: [<ffffffffa0039042>] virtblk_done+0x42/0xe0 [virtio_blk]
#1: (&(&bitmap->counts.lock)->rlock){-.....}, at: [<ffffffff81633718>] bitmap_endwrite+0x68/0x240
irq event stamp: 33518
hardirqs last enabled at (33515): [<ffffffff8102544f>] default_idle+0x1f/0x230
hardirqs last disabled at (33516): [<ffffffff818122ed>] common_interrupt+0x6d/0x72
softirqs last enabled at (33518): [<ffffffff810a1272>] _local_bh_enable+0x22/0x50
softirqs last disabled at (33517): [<ffffffff810a29e0>] irq_enter+0x60/0x80
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 3.16.0-0.rc2.git2.1.fc21.x86_64 #1
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
0000000000000000 f90db13964f4ee05 ffff88007d403b80 ffffffff81807b4c
0000000000000000 ffff88007d403ba8 ffffffff810d4f14 0000000000000000
0000000000441800 ffff880078fa1780 ffff88007d403c38 ffffffff8180caf2
Call Trace:
<IRQ> [<ffffffff81807b4c>] dump_stack+0x4d/0x66
[<ffffffff810d4f14>] __might_sleep+0x184/0x240
[<ffffffff8180caf2>] mutex_lock_nested+0x42/0x440
[<ffffffff812d76a0>] kernfs_notify+0x90/0x150
[<ffffffff8163377c>] bitmap_endwrite+0xcc/0x240
[<ffffffffa00de863>] close_write+0x93/0xb0 [raid1]
[<ffffffffa00df029>] r1_bio_write_done+0x29/0x50 [raid1]
[<ffffffffa00e0474>] raid1_end_write_request+0xe4/0x260 [raid1]
[<ffffffff813acb8b>] bio_endio+0x6b/0xa0
[<ffffffff813b46c4>] blk_update_request+0x94/0x420
[<ffffffff813bf0ea>] blk_mq_end_io+0x1a/0x70
[<ffffffffa00392c2>] virtblk_request_done+0x32/0x80 [virtio_blk]
[<ffffffff813c0648>] __blk_mq_complete_request+0x88/0x120
[<ffffffff813c070a>] blk_mq_complete_request+0x2a/0x30
[<ffffffffa0039066>] virtblk_done+0x66/0xe0 [virtio_blk]
[<ffffffffa002535a>] vring_interrupt+0x3a/0xa0 [virtio_ring]
[<ffffffff81116177>] handle_irq_event_percpu+0x77/0x340
[<ffffffff8111647d>] handle_irq_event+0x3d/0x60
[<ffffffff81119436>] handle_edge_irq+0x66/0x130
[<ffffffff8101c3e4>] handle_irq+0x84/0x150
[<ffffffff818146ad>] do_IRQ+0x4d/0xe0
[<ffffffff818122f2>] common_interrupt+0x72/0x72
<EOI> [<ffffffff8105f706>] ? native_safe_halt+0x6/0x10
[<ffffffff81025454>] default_idle+0x24/0x230
[<ffffffff81025f9f>] arch_cpu_idle+0xf/0x20
[<ffffffff810f5adc>] cpu_startup_entry+0x37c/0x7b0
[<ffffffff8104df1b>] start_secondary+0x25b/0x300
This patch fixes it by punting the notification delivery through a
work item. This ends up adding an extra pointer to kernfs_elem_attr
enlarging kernfs_node by a pointer, which is not ideal but not a very
big deal either. If this turns out to be an actual issue, we can move
kernfs_elem_attr->size to kernfs_node->iattr later.
Signed-off-by: Tejun Heo <[email protected]>
Reported-by: Josh Boyer <[email protected]>
Cc: Jens Axboe <[email protected]>
Reviewed-by: Michael S. Tsirkin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
We need to delete un-finished td from current request's td list
at ep_dequeue API, otherwise, this non-user td will be remained
at td list before this request is freed. So if we do ep_queue->
ep_dequeue->ep_queue sequence, when the complete interrupt for
the second ep_queue comes, we search td list for this request,
the first td (added by the first ep_queue) will be handled, and
its status is still active, so we will consider the this transfer
still not be completed, but in fact, it has completed. It causes
the peripheral side considers it never receives current data for
this transfer.
We met this problem when do "Error Recovery Test - Device Configured"
test item for USBCV2 MSC test, the host has never received ACK for
the IN token for CSW due to peripheral considers it does not get this
CBW, the USBCV test log like belows:
--------------------------------------------------------------------------
INFO
Issuing BOT MSC Reset, reset should always succeed
INFO
Retrieving status on CBW endpoint
INFO
CBW endpoint status = 0x0
INFO
Retrieving status on CSW endpoint
INFO
CSW endpoint status = 0x0
INFO
Issuing required command (Test Unit Ready) to verify device has recovered
INFO
Issuing CBW (attempt #1):
INFO
|----- CBW LUN = 0x0
INFO
|----- CBW Flags = 0x0
INFO
|----- CBW Data Transfer Length = 0x0
INFO
|----- CBW CDB Length = 0x6
INFO
|----- CBW CDB-00 = 0x0
INFO
|----- CBW CDB-01 = 0x0
INFO
|----- CBW CDB-02 = 0x0
INFO
|----- CBW CDB-03 = 0x0
INFO
|----- CBW CDB-04 = 0x0
INFO
|----- CBW CDB-05 = 0x0
INFO
Issuing CSW : try 1
INFO
CSW Bulk Request timed out!
ERROR
Failed CSW phase : should have been success or stall
FAIL
(5.3.4) The CSW status value must be 0x00, 0x01, or 0x02.
ERROR
BOTCommonMSCRequest failed: error=80004000
Cc: Andrzej Pietrasiewicz <[email protected]>
Cc: [email protected]
Signed-off-by: Peter Chen <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Disabling reading and writing to the trace file should not be able to
disable all function tracing callbacks. There's other users today
(like kprobes and perf). Reading a trace file should not stop those
from happening.
Cc: [email protected] # 3.0+
Reviewed-by: Masami Hiramatsu <[email protected]>
Signed-off-by: Steven Rostedt <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev fixes from Tomi Valkeinen:
"A few minor fbdev fixes for bfin_adv7393fb, omapdss, vt8500lcdfb,
atmel_lcdfb"
* tag 'fbdev-fixes-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
fb: adv7393: add missing semicolon
video: omapdss: Fix potential null pointer dereference
video: vt8500lcdfb: Remove kfree call since devm_kzalloc() is used
drivers:video:fbdev atmel_lcdfb.c power GPIO registration bug
|
|
Pull KVM fixes from Paolo Bonzini:
"A bunch of one-liners (except the s390 one).
The two more serious bugs ("KVM: SVM: Fix CPL export via SS.DPL" and
"KVM: s390: add sie.h uapi header file to Kbuild and remove header
dependency") were introduced in the 3.16 merge window"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: SVM: Fix CPL export via SS.DPL
KVM: s390: add sie.h uapi header file to Kbuild and remove header dependency
MIPS: KVM: Fix memory leak on VCPU
KVM: x86: preserve the high 32-bits of the PAT register
kvm: fix wrong address when writing Hyper-V tsc page
KVM: x86: Increase the number of fixed MTRR regs to 10
|
|
This prevents a panic: radeon_crtc_handle_page_flip() could run before
radeon_flip_work_func(), triggering the BUG_ON() in drm_vblank_put().
Tested-by: Dieter Nützel <[email protected]>
Reviewed-by: Christian König <[email protected]>
Signed-off-by: Michel Dänzer <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
We were using the vddc mask rather than the vddci mask.
Bug:
https://bugzilla.kernel.org/show_bug.cgi?id=79071
May also fix:
https://bugs.freedesktop.org/show_bug.cgi?id=69723
Noticed by: Dieter Nützel <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
Cc: [email protected]
|
|
We were using the vddc mask rather than the vddci mask.
Bug:
https://bugzilla.kernel.org/show_bug.cgi?id=79071
Possibly also fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=68571
Noticed-by: Jonathan Howard <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
Cc: [email protected]
|
|
v2: agd5f: compile fix
Signed-off-by: Stefan Brüns <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
Signed-off-by: Stefan Brüns <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
Some monitors seem to have problems with deep color enabled, even
though they claim to support it. I'm not sure if the monitor
need a quirk or if the driver is doing something the monitor doesn't
like. At this point lets just disable deep color by default like
we did for hdmi audio and work through the bugs so we can eventually
enable it by default.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=80531
Signed-off-by: Alex Deucher <[email protected]>
|
|
bapm enabled the GPU and CPU to share TDP headroom. It was
disabled by default since some laptops hung when it was enabled
in conjunction with dpm. It seems to be stable on desktop
boards and fixes hangs on boot with dpm enabled on certain
boards, so enable it by default on desktop boards.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=72921
Signed-off-by: Alex Deucher <[email protected]>
|
|
bapm allows the GPU and CPU to share TDP. This allows
for additional performance out of the GPU and CPU when
the headroom is available.
Signed-off-by: Alex Deucher <[email protected]>
|
|
Newer asics shouldn't need any manual adjustment.
Signed-off-by: Alex Deucher <[email protected]>
|
|
Set the default to 600Mhz if it's not set in the bios,
and bump the default to 600Mhz if it's lower than that.
This fixes display issues with certain 4k DP monitors when
using 5.4 Ghz DP clocks.
v2: fix typo.
Signed-off-by: Alex Deucher <[email protected]>
|
|
Commit f8bd493456c3da372ae81ed8f6b903f6207b9d98 by Jingoo Han
introduced this problem. This makes bfin_adv7393fb.c failed to compile.
Signed-off-by: Scott Jiang <[email protected]>
Signed-off-by: Tomi Valkeinen <[email protected]>
|
|
Drop WA to fix Voltage not getting dropped to Vmin when Gfx is power
gated for latest VLV revision.
Workaround fixed in Latest VLV revision. Forcing Gfx clk up not needed,
and Requesting the min freq should bring bring the voltage Vnn.
v2: Drop WA for Latest VLV revision (Ville)
Signed-off-by: Deepak S <[email protected]>
Reviewed-by: Ville Syrjälä <[email protected]>
[Jani: modified code comment, reformatted the commit message a bit.]
Signed-off-by: Jani Nikula <[email protected]>
|
|
This patch makes the msm ehci driver available to use on QCOM SOCs,
which have the same IP.
Signed-off-by: Srinivas Kandagatla <[email protected]>
Acked-by: Felipe Balbi <[email protected]>
Acked-by: Alan Stern <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Some buggy JMicron USB-ATA bridges don't know how to translate the FUA
bit in READs or WRITEs. This patch adds an entry in unusual_devs.h
and a blacklist flag to tell the sd driver not to use FUA.
Signed-off-by: Alan Stern <[email protected]>
Reported-by: Michael Büsch <[email protected]>
Tested-by: Michael Büsch <[email protected]>
Acked-by: James Bottomley <[email protected]>
CC: Matthew Dharm <[email protected]>
CC: <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v3.16-rc4
A few more fixes for this RC cycle. There's a revert of a previous patch
which ended up being the wrong version, so we reverted that commit and
applied a better fix.
CPPI41 got a race condition fix which was found by Thomas Gleixner.
The MSM PHY driver got a runtime pm usage fix so that it wouldn't
kill the PHY while it was still being used.
We also have a fix for a panic caused when removing musb_am335x driver.
Other than that, a few other minor fixes.
Signed-of-by: Felipe Balbi <[email protected]>
|
|
commit 943c13971c08 "usb: musb: dsps: implement ->set_mode()"
should have made it possible to use the driver with boards that have
the USBID pin unconnected. This doesn't actually work, since the
driver uses the wrong base address to access the mode register.
Furthermore it uses different base addresses in different places to
access the same register (phy_utmi).
Signed-off-by: Lothar Waßmann <[email protected]>
Signed-off-by: Felipe Balbi <[email protected]>
|
|
It appears that no one ever run ffs-test on a big-endian machine,
since it used cpu-endianess for fs_count and hs_count fields which
should be in little-endian format. Fix by wrapping the numbers in
cpu_to_le32.
Cc: [email protected]
Signed-off-by: Michal Nazarewicz <[email protected]>
Signed-off-by: Felipe Balbi <[email protected]>
|