aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2017-09-22IB/ipoib: Suppress the retry related completion errorsSantosh Shilimkar1-5/+11
IPoIB doesn't support transport/rnr retry schemes as per RFC so those errors are expected. No need to flood the log files with them. Tested-by: Michael Nowak <[email protected]> Tested-by: Rafael Alejandro Peralez <[email protected]> Tested-by: Liwen Huang <[email protected]> Tested-by: Hong Liu <[email protected]> Reviewed-by: Mukesh Kacker <[email protected]> Reported-by: Rajiv Raja <[email protected]> Signed-off-by: Santosh Shilimkar <[email protected]> Signed-off-by: Yuval Shaia <[email protected]> Signed-off-by: Doug Ledford <[email protected]>
2017-09-22Input: elan_i2c - extend Flash-Write delayKT Liao1-1/+1
The original 20ms delay is only marginally enough delay after a block write operation during firmware update. Let's increase the delay to ensure that the controller finishes up storing the page to avoid failures in the firmware updates. Signed-off-by: KT Liao <[email protected]> Signed-off-by: Dmitry Torokhov <[email protected]>
2017-09-22iw_cxgb4: remove the stid on listen create failureSteve Wise1-1/+1
If a listen create fails, then the server tid (stid) is incorrectly left in the stid idr table, which can cause a touch-after-free if the stid is looked up and the already freed endpoint is touched. So make sure and remove it in the error path. Cc: [email protected] Signed-off-by: Steve Wise <[email protected]> Signed-off-by: Doug Ledford <[email protected]>
2017-09-22iw_cxgb4: drop listen destroy replies if no ep foundSteve Wise1-0/+5
If the thread waiting for a CLOSE_LISTSRV_RPL times out and bails, then we need to handle a subsequent CPL if it arrives and the stid has been released. In this case silently drop it. Cc: [email protected] Signed-off-by: Steve Wise <[email protected]> Signed-off-by: Doug Ledford <[email protected]>
2017-09-22iw_cxgb4: put ep reference in pass_accept_req()Steve Wise1-1/+1
The listening endpoint should always be dereferenced at the end of pass_accept_req(). Fixes: f86fac79afec ("RDMA/iw_cxgb4: atomic find and reference for listening endpoints") Cc: [email protected] Signed-off-by: Steve Wise <[email protected]> Signed-off-by: Doug Ledford <[email protected]>
2017-09-22Merge tag 'for-linus-4.14b-rc2-tag' of ↵Linus Torvalds3-74/+68
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip Pull xen fixes from Juergen Gross: "A fix for a missing __init annotation and two cleanup patches" * tag 'for-linus-4.14b-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: xen, arm64: drop dummy lookup_address() xen: don't compile pv-specific parts if XEN_PV isn't configured xen: x86: mark xen_find_pt_base as __init
2017-09-22Merge tag 'powerpc-4.14-3' of ↵Linus Torvalds19-56/+77
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux Pull powerpc fixes from Michael Ellerman: "It turns out our single-fix pull from last week was too good to be true. I missed a few fixes in that pull that had already come in because I was on leave, but also we hadn't found the bugs yet. So this week it's a bit bigger, though not ridiculous. Hopefully things will settle down from here on. Four fixes for the new instruction emulation code. A fix for CPU offline on bare metal machines when certain idle states are not supported, and a fix for a device_node refcounting oops during CPU hotplug, caused by recent changes. Going to stable are a fix for an oops during core dump on machines that have TM (Transactional Memory) disabled. Reordering some EEH initialisation to avoid trashing memory, and another device_node refcounting fix. And a few other minor things. Thanks to: Anton Blanchard, Benjamin Herrenschmidt, Cyril Bur, Gautham R. Shenoy, Gustavo Romero, Kamalesh Babulal, Matthew Weber, Matt Weber, Naveen N. Rao, Nicholas Piggin, Pavithra Prakash, Ravi Bangoria, Ronak Desai, Scott Wood, Tyrel Datwyler" * tag 'powerpc-4.14-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: powerpc/pseries: Fix parent_dn reference leak in add_dt_node() powerpc/pseries: Fix "OF: ERROR: Bad of_node_put() on /cpus" during DLPAR powerpc/eeh: Create PHB PEs after EEH is initialized powerpc/kprobes: Update optprobes to use emulate_update_regs() powerpc/powernv: Clear LPCR[PECE1] via stop-api only for deep state offline powerpc/sstep: mullw should calculate a 64 bit signed result powerpc/sstep: Fix issues with mcrf powerpc/sstep: Fix issues with set_cr0() powerpc/tm: Flush TM only if CPU has TM feature powerpc/sysrq: Fix oops whem ppmu is not registered powerpc/configs: Update for CONFIG_SND changes powerpc/e6500: Update machine check for L1D cache err
2017-09-22Merge branch '4.14-fixes' of ↵Linus Torvalds27-33/+37
git://git.linux-mips.org/pub/scm/ralf/upstream-linus Pull MIPS fixes from Ralf Baechle: - Fix a build error on MSP71xx which used to rely on somehow magically <asm/setup.h> being pulled in which no longer happens. - Fix the __write_64bit_c0_split inline assembler where there was the theoretical possibility of GCC interpret the constraints such that bad code could result. - A __init was causing section mismatch errors on Alchemy. Just to be on the safe side, Manuel's patch does away with all of them. - Fix perf event init. * '4.14-fixes' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: MIPS: PCI: fix pcibios_map_irq section mismatch MIPS: Fix input modify in __write_64bit_c0_split() MIPS: MSP71xx: Include asm/setup.h MIPS: Fix perf event init
2017-09-22Merge branch 'for-linus' of ↵Linus Torvalds11-42/+183
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux Pull s390 fixes from Martin Schwidefsky: - A couple of bug fixes: memory management, perf, cio, dasd and scm_blk. - A larger change in regard to the CPU topology to improve performance for systems running under z/VM or KVM. * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: s390/topology: enable / disable topology dynamically s390/topology: alternative topology for topology-less machines s390/mm: fix write access check in gup_huge_pmd() s390/mm: make pmdp_invalidate() do invalidation only s390/cio: recover from bad paths s390/scm_blk: consistently use blk_status_t as error type s390/dasd: fix race during dasd initialization s390/perf: fix bug when creating per-thread event
2017-09-22USB: g_mass_storage: Fix deadlock when driver is unboundAlan Stern3-57/+10
As a holdover from the old g_file_storage gadget, the g_mass_storage legacy gadget driver attempts to unregister itself when its main operating thread terminates (if it hasn't been unregistered already). This is not strictly necessary; it was never more than an attempt to have the gadget fail cleanly if something went wrong and the main thread was killed. However, now that the UDC core manages gadget drivers independently of UDC drivers, this scheme doesn't work any more. A simple test: modprobe dummy-hcd modprobe g-mass-storage file=... rmmod dummy-hcd ends up in a deadlock with the following backtrace: sysrq: SysRq : Show Blocked State task PC stack pid father file-storage D 0 1130 2 0x00000000 Call Trace: __schedule+0x53e/0x58c schedule+0x6e/0x77 schedule_preempt_disabled+0xd/0xf __mutex_lock.isra.1+0x129/0x224 ? _raw_spin_unlock_irqrestore+0x12/0x14 __mutex_lock_slowpath+0x12/0x14 mutex_lock+0x28/0x2b usb_gadget_unregister_driver+0x29/0x9b [udc_core] usb_composite_unregister+0x10/0x12 [libcomposite] msg_cleanup+0x1d/0x20 [g_mass_storage] msg_thread_exits+0xd/0xdd7 [g_mass_storage] fsg_main_thread+0x1395/0x13d6 [usb_f_mass_storage] ? __schedule+0x573/0x58c kthread+0xd9/0xdb ? do_set_interface+0x25c/0x25c [usb_f_mass_storage] ? init_completion+0x1e/0x1e ret_from_fork+0x19/0x24 rmmod D 0 1155 683 0x00000000 Call Trace: __schedule+0x53e/0x58c schedule+0x6e/0x77 schedule_timeout+0x26/0xbc ? __schedule+0x573/0x58c do_wait_for_common+0xb3/0x128 ? usleep_range+0x81/0x81 ? wake_up_q+0x3f/0x3f wait_for_common+0x2e/0x45 wait_for_completion+0x17/0x19 fsg_common_put+0x34/0x81 [usb_f_mass_storage] fsg_free_inst+0x13/0x1e [usb_f_mass_storage] usb_put_function_instance+0x1a/0x25 [libcomposite] msg_unbind+0x2a/0x42 [g_mass_storage] __composite_unbind+0x4a/0x6f [libcomposite] composite_unbind+0x12/0x14 [libcomposite] usb_gadget_remove_driver+0x4f/0x77 [udc_core] usb_del_gadget_udc+0x52/0xcc [udc_core] dummy_udc_remove+0x27/0x2c [dummy_hcd] platform_drv_remove+0x1d/0x31 device_release_driver_internal+0xe9/0x16d device_release_driver+0x11/0x13 bus_remove_device+0xd2/0xe2 device_del+0x19f/0x221 ? selinux_capable+0x22/0x27 platform_device_del+0x21/0x63 platform_device_unregister+0x10/0x1a cleanup+0x20/0x817 [dummy_hcd] SyS_delete_module+0x10c/0x197 ? ____fput+0xd/0xf ? task_work_run+0x55/0x62 ? prepare_exit_to_usermode+0x65/0x75 do_fast_syscall_32+0x86/0xc3 entry_SYSENTER_32+0x4e/0x7c What happens is that removing the dummy-hcd driver causes the UDC core to unbind the gadget driver, which it does while holding the udc_lock mutex. The unbind routine in g_mass_storage tells the main thread to exit and waits for it to terminate. But as mentioned above, when the main thread exits it tries to unregister the mass-storage function driver. Via the composite framework this ends up calling usb_gadget_unregister_driver(), which tries to acquire the udc_lock mutex. The result is deadlock. The simplest way to fix the problem is not to be so clever: The main thread doesn't have to unregister the function driver. The side effects won't be so terrible; if the gadget is still attached to a USB host when the main thread is killed, it will appear to the host as though the gadget's firmware has crashed -- a reasonably accurate interpretation, and an all-too-common occurrence for USB mass-storage devices. In fact, the code to unregister the driver when the main thread exits is specific to g-mass-storage; it is not used when f-mass-storage is included as a function in a larger composite device. Therefore the entire mechanism responsible for this (the fsg_operations structure with its ->thread_exits method, the fsg_common_set_ops() routine, and the msg_thread_exits() callback routine) can all be eliminated. Even the msg_registered bitflag can be removed, because now the driver is unregistered in only one place rather than in two places. Signed-off-by: Alan Stern <[email protected]> CC: <[email protected]> Acked-by: Felipe Balbi <[email protected]> Acked-by: Michal Nazarewicz <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2017-09-22USB: gadgetfs: Fix crash caused by inadequate synchronizationAlan Stern1-5/+36
The gadgetfs driver (drivers/usb/gadget/legacy/inode.c) was written before the UDC and composite frameworks were adopted; it is a legacy driver. As such, it expects that once bound to a UDC controller, it will not be unbound until it unregisters itself. However, the UDC framework does unbind function drivers while they are still registered. When this happens, it can cause the gadgetfs driver to misbehave or crash. For example, userspace can cause a crash by opening the device file and doing an ioctl call before setting up a configuration (found by Andrey Konovalov using the syzkaller fuzzer). This patch adds checks and synchronization to prevent these bad behaviors. It adds a udc_usage counter that the driver increments at times when it is using a gadget interface without holding the private spinlock. The unbind routine waits for this counter to go to 0 before returning, thereby ensuring that the UDC is no longer in use. The patch also adds a check in the dev_ioctl() routine to make sure the driver is bound to a UDC before dereferencing the gadget pointer, and it makes destroy_ep_files() synchronize with the endpoint I/O routines, to prevent the user from accessing an endpoint data structure after it has been removed. Signed-off-by: Alan Stern <[email protected]> Reported-by: Andrey Konovalov <[email protected]> Tested-by: Andrey Konovalov <[email protected]> CC: <[email protected]> Acked-by: Felipe Balbi <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2017-09-22USB: gadgetfs: fix copy_to_user while holding spinlockAlan Stern1-1/+4
The gadgetfs driver as a long-outstanding FIXME, regarding a call of copy_to_user() made while holding a spinlock. This patch fixes the issue by dropping the spinlock and using the dev->udc_usage mechanism introduced by another recent patch to guard against status changes while the lock isn't held. Signed-off-by: Alan Stern <[email protected]> Reported-by: Andrey Konovalov <[email protected]> CC: <[email protected]> Acked-by: Felipe Balbi <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2017-09-22USB: uas: fix bug in handling of alternate settingsAlan Stern2-12/+13
The uas driver has a subtle bug in the way it handles alternate settings. The uas_find_uas_alt_setting() routine returns an altsetting value (the bAlternateSetting number in the descriptor), but uas_use_uas_driver() then treats that value as an index to the intf->altsetting array, which it isn't. Normally this doesn't cause any problems because the various alternate settings have bAlternateSetting values 0, 1, 2, ..., so the value is equal to the index in the array. But this is not guaranteed, and Andrey Konovalov used the syzkaller fuzzer with KASAN to get a slab-out-of-bounds error by violating this assumption. This patch fixes the bug by making uas_find_uas_alt_setting() return a pointer to the altsetting entry rather than either the value or the index. Pointers are less subject to misinterpretation. Signed-off-by: Alan Stern <[email protected]> Reported-by: Andrey Konovalov <[email protected]> Tested-by: Andrey Konovalov <[email protected]> CC: Oliver Neukum <[email protected]> CC: <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2017-09-22Merge branch 'linus' of ↵Linus Torvalds20-212/+236
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6 Pull crypto fixes from Herbert Xu: - Fix compiler warnings in inside-secure - Fix LS1021A support in caam - Avoid using RBP in x86 crypto code - Fix bug in talitos that prevents hashing with algif - Fix bugs talitos hashing code that cause incorrect hash result - Fix memory freeing path bug in drbg - Fix af_alg crash when two SG lists are chained * 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: crypto: af_alg - update correct dst SGL entry crypto: caam - fix LS1021A support on ARMv7 multiplatform kernel crypto: inside-secure - fix gcc-4.9 warnings crypto: talitos - Don't provide setkey for non hmac hashing algs crypto: talitos - fix hashing crypto: talitos - fix sha224 crypto: x86/twofish - Fix RBP usage crypto: sha512-avx2 - Fix RBP usage crypto: x86/sha256-ssse3 - Fix RBP usage crypto: x86/sha256-avx2 - Fix RBP usage crypto: x86/sha256-avx - Fix RBP usage crypto: x86/sha1-ssse3 - Fix RBP usage crypto: x86/sha1-avx2 - Fix RBP usage crypto: x86/des3_ede - Fix RBP usage crypto: x86/cast6 - Fix RBP usage crypto: x86/cast5 - Fix RBP usage crypto: x86/camellia - Fix RBP usage crypto: x86/blowfish - Fix RBP usage crypto: drbg - fix freeing of resources
2017-09-22IB/core: Fix for core panicAlex Estrin1-2/+2
Build with the latest patches resulted in panic: 11384.486289] BUG: unable to handle kernel NULL pointer dereference at (null) [11384.486293] IP: (null) [11384.486295] PGD 0 [11384.486295] P4D 0 [11384.486296] [11384.486299] Oops: 0010 [#1] SMP ......... snip ...... [11384.486401] CPU: 0 PID: 968 Comm: kworker/0:1H Tainted: G W O 4.13.0-a-stream-20170825 #1 [11384.486402] Hardware name: Intel Corporation S2600WT2R/S2600WT2R, BIOS SE5C610.86B.01.01.0014.121820151719 12/18/2015 [11384.486418] Workqueue: ib-comp-wq ib_cq_poll_work [ib_core] [11384.486419] task: ffff880850579680 task.stack: ffffc90007fec000 [11384.486420] RIP: 0010: (null) [11384.486420] RSP: 0018:ffffc90007fef970 EFLAGS: 00010206 [11384.486421] RAX: ffff88084cfe8000 RBX: ffff88084dce4000 RCX: ffffc90007fef978 [11384.486422] RDX: 0000000000000000 RSI: 0000000000000001 RDI: ffff88084cfe8000 [11384.486422] RBP: ffffc90007fefab0 R08: 0000000000000000 R09: ffff88084dce4080 [11384.486423] R10: ffffffffa02d7f60 R11: 0000000000000000 R12: ffff88105af65a00 [11384.486423] R13: ffff88084dce4000 R14: 000000000000c000 R15: 000000000000c000 [11384.486424] FS: 0000000000000000(0000) GS:ffff88085f400000(0000) knlGS:0000000000000000 [11384.486425] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [11384.486425] CR2: 0000000000000000 CR3: 0000000001c09000 CR4: 00000000001406f0 [11384.486426] Call Trace: [11384.486431] ? is_valid_mcast_lid.isra.21+0xfb/0x110 [ib_core] [11384.486436] ib_attach_mcast+0x6f/0xa0 [ib_core] [11384.486441] ipoib_mcast_attach+0x81/0x190 [ib_ipoib] [11384.486443] ipoib_mcast_join_complete+0x354/0xb40 [ib_ipoib] [11384.486448] mcast_work_handler+0x330/0x6c0 [ib_core] [11384.486452] join_handler+0x101/0x220 [ib_core] [11384.486455] ib_sa_mcmember_rec_callback+0x54/0x80 [ib_core] [11384.486459] recv_handler+0x3a/0x60 [ib_core] [11384.486462] ib_mad_recv_done+0x423/0x9b0 [ib_core] [11384.486466] __ib_process_cq+0x5d/0xb0 [ib_core] [11384.486469] ib_cq_poll_work+0x20/0x60 [ib_core] [11384.486472] process_one_work+0x149/0x360 [11384.486474] worker_thread+0x4d/0x3c0 [11384.486487] kthread+0x109/0x140 [11384.486488] ? rescuer_thread+0x380/0x380 [11384.486489] ? kthread_park+0x60/0x60 [11384.486490] ? kthread_park+0x60/0x60 [11384.486493] ret_from_fork+0x25/0x30 [11384.486493] Code: Bad RIP value. [11384.486493] Code: Bad RIP value. [11384.486496] RIP: (null) RSP: ffffc90007fef970 [11384.486497] CR2: 0000000000000000 [11384.486531] ---[ end trace b1acec6fb4ff6e75 ]--- [11384.532133] Kernel panic - not syncing: Fatal exception [11384.536541] Kernel Offset: disabled [11384.969491] ---[ end Kernel panic - not syncing: Fatal exception [11384.976875] sched: Unexpected reschedule of offline CPU#1! [11384.983646] ------------[ cut here ]------------ Rdma device driver may not have implemented (*get_link_layer)() so it can not be called directly. Should use appropriate helper function. Reviewed-by: Yuval Shaia <[email protected]> Fixes: 523633359224 ("IB/core: Fix the validations of a multicast LID in attach or detach operations") Cc: [email protected] # 4.13 Reviewed-by: Dennis Dalessandro <[email protected]> Signed-off-by: Alex Estrin <[email protected]> Signed-off-by: Dennis Dalessandro <[email protected]> Reviewed-by: Leon Romanovsky <[email protected]> Signed-off-by: Doug Ledford <[email protected]>
2017-09-22cgroup: Reinit cgroup_taskset structure before cgroup_migrate_execute() returnsWaiman Long1-0/+8
The cgroup_taskset structure within the larger cgroup_mgctx structure is supposed to be used once and then discarded. That is not really the case in the hotplug code path: cpuset_hotplug_workfn() - cgroup_transfer_tasks() - cgroup_migrate() - cgroup_migrate_add_task() - cgroup_migrate_execute() In this case, the cgroup_migrate() function is called multiple time with the same cgroup_mgctx structure to transfer the tasks from one cgroup to another one-by-one. The second time cgroup_migrate() is called, the cgroup_taskset will be in an incorrect state and so may cause the system to panic. For example, [ 150.888410] Faulting instruction address: 0xc0000000001db648 [ 150.888414] Oops: Kernel access of bad area, sig: 11 [#1] [ 150.888417] SMP NR_CPUS=2048 [ 150.888417] NUMA [ 150.888419] pSeries : [ 150.888545] NIP [c0000000001db648] cpuset_can_attach+0x58/0x1b0 [ 150.888548] LR [c0000000001db638] cpuset_can_attach+0x48/0x1b0 [ 150.888551] Call Trace: [ 150.888554] [c0000005f65cb940] [c0000000001db638] cpuset_can_attach+0x48/0x1b 0 (unreliable) [ 150.888559] [c0000005f65cb9a0] [c0000000001cff04] cgroup_migrate_execute+0xc4/0x4b0 [ 150.888563] [c0000005f65cba20] [c0000000001d7d14] cgroup_transfer_tasks+0x1d4/0x370 [ 150.888568] [c0000005f65cbb70] [c0000000001ddcb0] cpuset_hotplug_workfn+0x710/0x8f0 [ 150.888572] [c0000005f65cbc80] [c00000000012032c] process_one_work+0x1ac/0x4d0 [ 150.888576] [c0000005f65cbd20] [c0000000001206f8] worker_thread+0xa8/0x5b0 [ 150.888580] [c0000005f65cbdc0] [c0000000001293f8] kthread+0x168/0x1b0 [ 150.888584] [c0000005f65cbe30] [c00000000000b368] ret_from_kernel_thread+0x5c/0x74 To allow reuse of the cgroup_mgctx structure, some fields in that structure are now re-initialized at the end of cgroup_migrate_execute() function call so that the structure can be reused again in a later iteration without causing problem. This bug was introduced in the commit e595cd706982 ("group: track migration context in cgroup_mgctx") in 4.11. This commit moves the cgroup_taskset initialization out of cgroup_migrate(). The commit 10467270fb3 ("cgroup: don't call migration methods if there are no tasks to migrate") helped, but did not completely resolve the problem. Fixes: e595cd706982bff0211e6fafe5a108421e747fbc ("group: track migration context in cgroup_mgctx") Signed-off-by: Waiman Long <[email protected]> Signed-off-by: Tejun Heo <[email protected]> Cc: [email protected] # v4.11+
2017-09-22ALSA: usb-audio: Check out-of-bounds access by corrupted buffer descriptorTakashi Iwai1-0/+20
When a USB-audio device receives a maliciously adjusted or corrupted buffer descriptor, the USB-audio driver may access an out-of-bounce value at its parser. This was detected by syzkaller, something like: BUG: KASAN: slab-out-of-bounds in usb_audio_probe+0x27b2/0x2ab0 Read of size 1 at addr ffff88006b83a9e8 by task kworker/0:1/24 CPU: 0 PID: 24 Comm: kworker/0:1 Not tainted 4.14.0-rc1-42251-gebb2c2437d80 #224 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011 Workqueue: usb_hub_wq hub_event Call Trace: __dump_stack lib/dump_stack.c:16 dump_stack+0x292/0x395 lib/dump_stack.c:52 print_address_description+0x78/0x280 mm/kasan/report.c:252 kasan_report_error mm/kasan/report.c:351 kasan_report+0x22f/0x340 mm/kasan/report.c:409 __asan_report_load1_noabort+0x19/0x20 mm/kasan/report.c:427 snd_usb_create_streams sound/usb/card.c:248 usb_audio_probe+0x27b2/0x2ab0 sound/usb/card.c:605 usb_probe_interface+0x35d/0x8e0 drivers/usb/core/driver.c:361 really_probe drivers/base/dd.c:413 driver_probe_device+0x610/0xa00 drivers/base/dd.c:557 __device_attach_driver+0x230/0x290 drivers/base/dd.c:653 bus_for_each_drv+0x161/0x210 drivers/base/bus.c:463 __device_attach+0x26e/0x3d0 drivers/base/dd.c:710 device_initial_probe+0x1f/0x30 drivers/base/dd.c:757 bus_probe_device+0x1eb/0x290 drivers/base/bus.c:523 device_add+0xd0b/0x1660 drivers/base/core.c:1835 usb_set_configuration+0x104e/0x1870 drivers/usb/core/message.c:1932 generic_probe+0x73/0xe0 drivers/usb/core/generic.c:174 usb_probe_device+0xaf/0xe0 drivers/usb/core/driver.c:266 really_probe drivers/base/dd.c:413 driver_probe_device+0x610/0xa00 drivers/base/dd.c:557 __device_attach_driver+0x230/0x290 drivers/base/dd.c:653 bus_for_each_drv+0x161/0x210 drivers/base/bus.c:463 __device_attach+0x26e/0x3d0 drivers/base/dd.c:710 device_initial_probe+0x1f/0x30 drivers/base/dd.c:757 bus_probe_device+0x1eb/0x290 drivers/base/bus.c:523 device_add+0xd0b/0x1660 drivers/base/core.c:1835 usb_new_device+0x7b8/0x1020 drivers/usb/core/hub.c:2457 hub_port_connect drivers/usb/core/hub.c:4903 hub_port_connect_change drivers/usb/core/hub.c:5009 port_event drivers/usb/core/hub.c:5115 hub_event+0x194d/0x3740 drivers/usb/core/hub.c:5195 process_one_work+0xc7f/0x1db0 kernel/workqueue.c:2119 worker_thread+0x221/0x1850 kernel/workqueue.c:2253 kthread+0x3a1/0x470 kernel/kthread.c:231 ret_from_fork+0x2a/0x40 arch/x86/entry/entry_64.S:431 This patch adds the checks of out-of-bounce accesses at appropriate places and bails out when it goes out of the given buffer. Reported-by: Andrey Konovalov <[email protected]> Tested-by: Andrey Konovalov <[email protected]> Cc: <[email protected]> Signed-off-by: Takashi Iwai <[email protected]>
2017-09-22drivers/perf: arm_pmu_acpi: Release memory obtained by kasprintfArvind Yadav1-0/+1
Free memory region, if arm_pmu_acpi_probe is not successful. Acked-by: Will Deacon <[email protected]> Signed-off-by: Arvind Yadav <[email protected]> Signed-off-by: Catalin Marinas <[email protected]>
2017-09-22iommu/of: Remove PCI host bridge node checkRobin Murphy1-4/+1
of_pci_iommu_init() tries to be clever and stop its alias walk at the device represented by master_np, in case of weird PCI topologies where the bridge to the IOMMU and the rest of the system is not at the root. It turns out this is a bit short-sighted, since there are plenty of other callers of pci_for_each_dma_alias() which would also need the same behaviour in that situation, and the only platform so far with such a topology (Cavium ThunderX2) already solves it more generally via a PCI quirk. As this check is effectively redundant, and returning a boolean value as an int is a bit broken anyway, let's just get rid of it. Reported-by: Jean-Philippe Brucker <[email protected]> Fixes: d87beb749281 ("iommu/of: Handle PCI aliases properly") Signed-off-by: Robin Murphy <[email protected]> Tested-by: Jean-Philippe Brucker <[email protected]> Signed-off-by: Joerg Roedel <[email protected]>
2017-09-22ALSA: pcm: Fix structure definition for X32 ABIBaolin Wang1-0/+1
X32 ABI uses the 64bit timespec in addition to 64bit alignment of 64bit values. We have added compat ABI for these ioctls, but this patch adds one missing padding into 'struct snd_pcm_mmap_status_x32' to fix incompatibilities. Signed-off-by: Baolin Wang <[email protected]> Signed-off-by: Takashi Iwai <[email protected]>
2017-09-22mmc: sdhci-pci: Fix voltage switch for some Intel host controllersAdrian Hunter1-0/+15
Some Intel host controllers (e.g. CNP) use an ACPI device-specific method to ensure correct voltage switching. Fix voltage switch for those, by adding a call to the DSM. Signed-off-by: Adrian Hunter <[email protected]> Cc: [email protected] Signed-off-by: Ulf Hansson <[email protected]>
2017-09-22staging: rtl8723bs: avoid null pointer dereference on pmlmeprivColin Ian King1-2/+1
There is a check to see if pmlmepriv is null before vfree'ing pmlmepriv->free_bss_buf hence implying pmlmepriv could potenially be null. However, a previous call to rtw_free_mlme_priv_ie_data can also dereference pmlmepriv, so move this call so that it is only called if pmlmepriv non-null. Detected by CoverityScan, CID#1077739 ("Dereference before null check") Fixes: 554c0a3abf21 ("staging: Add rtl8723bs sdio wifi driver") Signed-off-by: Colin Ian King <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2017-09-22staging: rtl8723bs: add missing range check on idColin Ian King1-0/+2
The value of the u8 id needs to be upper bounds checked to ensure the cam_cache array on the adapter dvobj is not indexed outside of the allowed range of 0..TOTAL_CAM_ENTRY-1. This can currently occur if id is >= TOTAL_CAM_ENTRY when calling write_cam_from_cache. Fix this by adding an upper range check. Detected by CoverityScan, CID#1428464 ("Use of untrusted scalar value") Fixes: 554c0a3abf21 ("staging: Add rtl8723bs sdio wifi driver") Signed-off-by: Colin Ian King <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2017-09-22mmc: tmio: remove broken and noisy debug macroWolfram Sang1-47/+0
Some change for v4.14 broke the debug output for TMIO. But since it was not helpful to me and too noisy for my taste anyhow, let's just remove it instead of fixing it. We'll find something better if we'd need it... Signed-off-by: Wolfram Sang <[email protected]> Signed-off-by: Ulf Hansson <[email protected]>
2017-09-22KVM: PPC: Book3S HV: Check for updated HDSISR on P9 HDSI exceptionMichael Neuling1-1/+13
On POWER9 DD2.1 and below, sometimes on a Hypervisor Data Storage Interrupt (HDSI) the HDSISR is not be updated at all. To work around this we put a canary value into the HDSISR before returning to a guest and then check for this canary when we take a HDSI. If we find the canary on a HDSI, we know the hardware didn't update the HDSISR. In this case we return to the guest to retake the HDSI which should correctly update the HDSISR the second time HDSI entry. After talking to Paulus we've applied this workaround to all POWER9 CPUs. The workaround of returning to the guest shouldn't ever be triggered on well behaving CPU. The extra instructions should have negligible performance impact. Signed-off-by: Michael Neuling <[email protected]> Signed-off-by: Paolo Bonzini <[email protected]>
2017-09-22KVM: nVMX: fix HOST_CR3/HOST_CR4 cacheLadi Prosek1-8/+8
For nested virt we maintain multiple VMCS that can run on a vCPU. So it is incorrect to keep vmcs_host_cr3 and vmcs_host_cr4, whose purpose is caching the value of the rarely changing HOST_CR3 and HOST_CR4 VMCS fields, in vCPU-wide data structures. Hyper-V nested on KVM runs into this consistently for me with PCID enabled. CR3 is updated with a new value, unlikely(cr3 != vmx->host_state.vmcs_host_cr3) fires, and the currently loaded VMCS is updated. Then we switch from L2 to L1 and the next exit reverts CR3 to its old value. Fixes: d6e41f1151fe ("x86/mm, KVM: Teach KVM's VMX code that CR3 isn't a constant") Signed-off-by: Ladi Prosek <[email protected]> Cc: [email protected] Signed-off-by: Paolo Bonzini <[email protected]>
2017-09-22Drivers: hv: fcopy: restore correct transfer lengthOlaf Hering1-0/+4
Till recently the expected length of bytes read by the daemon did depend on the context. It was either hv_start_fcopy or hv_do_fcopy. The daemon had a buffer size of two pages, which was much larger than needed. Now the expected length of bytes read by the daemon changed slightly. For START_FILE_COPY it is still the size of hv_start_fcopy. But for WRITE_TO_FILE and the other operations it is as large as the buffer that arrived via vmbus. In case of WRITE_TO_FILE that is slightly larger than a struct hv_do_fcopy. Since the buffer in the daemon was still larger everything was fine. Currently, the daemon reads only what is actually needed. The new buffer layout is as large as a struct hv_do_fcopy, for the WRITE_TO_FILE operation. Since the kernel expects a slightly larger size, hvt_op_read will return -EINVAL because the daemon will read slightly less than expected. Address this by restoring the expected buffer size in case of WRITE_TO_FILE. Fixes: 'c7e490fc23eb ("Drivers: hv: fcopy: convert to hv_utils_transport")' Fixes: '3f2baa8a7d2e ("Tools: hv: update buffer handling in hv_fcopy_daemon")' Signed-off-by: Olaf Hering <[email protected]> Signed-off-by: K. Y. Srinivasan <[email protected]> Cc: [email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2017-09-22vmbus: don't acquire the mutex in vmbus_hvsock_device_unregister()Dexuan Cui1-4/+0
Due to commit 54a66265d675 ("Drivers: hv: vmbus: Fix rescind handling"), we need this patch to resolve the below deadlock: after we get the mutex in vmbus_hvsock_device_unregister() and call vmbus_device_unregister() -> device_unregister() -> ... -> device_release() -> vmbus_device_release(), we'll get a deadlock, because vmbus_device_release() tries to get the same mutex. Signed-off-by: Dexuan Cui <[email protected]> Cc: K. Y. Srinivasan <[email protected]> Cc: Haiyang Zhang <[email protected]> Cc: Stephen Hemminger <[email protected]> Signed-off-by: K. Y. Srinivasan <[email protected]> Cc: [email protected] (4.13 and above) Signed-off-by: Greg Kroah-Hartman <[email protected]>
2017-09-22intel_th: pci: Add Lewisburg PCH supportAlexander Shishkin1-0/+5
This adds Intel(R) Trace Hub PCI ID for Lewisburg PCH. Signed-off-by: Alexander Shishkin <[email protected]> Cc: [email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2017-09-22intel_th: pci: Add Cedar Fork PCH supportAlexander Shishkin1-0/+5
This adds Intel(R) Trace Hub PCI ID for Cedar Fork PCH. Signed-off-by: Alexander Shishkin <[email protected]> Cc: [email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2017-09-22stm class: Fix a use-after-freeAlexander Shishkin1-1/+1
For reasons unknown, the stm_source removal path uses device_destroy() to kill the underlying device object. Because device_destroy() uses devt to look for the device to destroy and the fact that stm_source devices don't have one (or all have the same one), it just picks the first device in the class, which may well be the wrong one. That is, loading stm_console and stm_heartbeat and then removing both will die in dereferencing a freed object. Since this should have been device_unregister() in the first place, use it instead of device_destroy(). Signed-off-by: Alexander Shishkin <[email protected]> Fixes: 7bd1d4093c2 ("stm class: Introduce an abstraction for System Trace Module devices") Cc: [email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2017-09-22usb-storage: unusual_devs entry to fix write-access regression for Seagate ↵Alan Stern1-0/+7
external drives Kris Lindgren reports that without the NO_WP_DETECT flag, his Seagate external disk drive fails all write accesses. This regresssion dates back approximately to the start of the 4.x kernel releases. Signed-off-by: Alan Stern <[email protected]> Reported-by: Kris Lindgren <[email protected]> CC: <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2017-09-22usb-storage: fix bogus hardware error messages for ATA pass-thru devicesAlan Stern1-1/+13
Ever since commit a621bac3044e ("scsi_lib: correctly retry failed zero length REQ_TYPE_FS commands"), people have been getting bogus error messages for USB disk drives using ATA pass-thru. For example: [ 1344.880193] sd 6:0:0:0: [sdb] Attached SCSI disk [ 1345.069152] sd 6:0:0:0: [sdb] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_SENSE [ 1345.069159] sd 6:0:0:0: [sdb] tag#0 Sense Key : Hardware Error [current] [descriptor] [ 1345.069162] sd 6:0:0:0: [sdb] tag#0 Add. Sense: No additional sense information [ 1345.069168] sd 6:0:0:0: [sdb] tag#0 CDB: ATA command pass through(16) 85 06 20 00 00 00 00 00 00 00 00 00 00 00 e5 00 [ 1345.172252] sd 6:0:0:0: [sdb] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_SENSE [ 1345.172258] sd 6:0:0:0: [sdb] tag#0 Sense Key : Hardware Error [current] [descriptor] [ 1345.172261] sd 6:0:0:0: [sdb] tag#0 Add. Sense: No additional sense information [ 1345.172266] sd 6:0:0:0: [sdb] tag#0 CDB: ATA command pass through(12)/Blank a1 06 20 da 00 00 4f c2 00 b0 00 00 These messages can be quite annoying, because programs like udisks2 provoke them every 10 minutes or so. Other programs can also have this effect, such as those in smartmontools. I don't fully understand how that commit induced the SCSI core to log these error messages, but the underlying cause for them is code added to usb-storage by commit f1a0743bc0e7 ("USB: storage: When a device returns no sense data, call it a Hardware Error"). At the time it was necessary to do this, in order to prevent an infinite retry loop with some not-so-great mass storage devices. However, the ATA pass-thru protocol uses SCSI sense data to return command status values, and some devices always report Check Condition status for ATA pass-thru commands to ensure that the host retrieves the sense data, even if the command succeeded. This violates the USB mass-storage protocol (Check Condition status is supposed to mean the command failed), but we can't help that. This patch attempts to mitigate the problem of these bogus error reports by changing usb-storage. The HARDWARE ERROR sense key will be inserted only for commands that aren't ATA pass-thru. Thanks to Ewan Milne for pointing out that this mechanism was present in usb-storage. 8 years after writing it, I had completely forgotten its existence. Signed-off-by: Alan Stern <[email protected]> Tested-by: Kris Lindgren <[email protected]> Ref: https://bugzilla.redhat.com/show_bug.cgi?id=1351305 CC: Ewan D. Milne <[email protected]> CC: <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2017-09-22drm/sun4i: cec: Enable back CEC-pin frameworkHans Verkuil2-2/+2
Now that the cec-pin framework has been merged, we can remove the safeguard that were preventing the CEC part of the sun4i HDMI driver and actually start to use it. Signed-off-by: Hans Verkuil <[email protected]> Signed-off-by: Maxime Ripard <[email protected]>
2017-09-21net: prevent dst uses after freeEric Dumazet3-20/+6
In linux-4.13, Wei worked hard to convert dst to a traditional refcounted model, removing GC. We now want to make sure a dst refcount can not transition from 0 back to 1. The problem here is that input path attached a not refcounted dst to an skb. Then later, because packet is forwarded and hits skb_dst_force() before exiting RCU section, we might try to take a refcount on one dst that is about to be freed, if another cpu saw 1 -> 0 transition in dst_release() and queued the dst for freeing after one RCU grace period. Lets unify skb_dst_force() and skb_dst_force_safe(), since we should always perform the complete check against dst refcount, and not assume it is not zero. Bugzilla : https://bugzilla.kernel.org/show_bug.cgi?id=197005 [ 989.919496] skb_dst_force+0x32/0x34 [ 989.919498] __dev_queue_xmit+0x1ad/0x482 [ 989.919501] ? eth_header+0x28/0xc6 [ 989.919502] dev_queue_xmit+0xb/0xd [ 989.919504] neigh_connected_output+0x9b/0xb4 [ 989.919507] ip_finish_output2+0x234/0x294 [ 989.919509] ? ipt_do_table+0x369/0x388 [ 989.919510] ip_finish_output+0x12c/0x13f [ 989.919512] ip_output+0x53/0x87 [ 989.919513] ip_forward_finish+0x53/0x5a [ 989.919515] ip_forward+0x2cb/0x3e6 [ 989.919516] ? pskb_trim_rcsum.part.9+0x4b/0x4b [ 989.919518] ip_rcv_finish+0x2e2/0x321 [ 989.919519] ip_rcv+0x26f/0x2eb [ 989.919522] ? vlan_do_receive+0x4f/0x289 [ 989.919523] __netif_receive_skb_core+0x467/0x50b [ 989.919526] ? tcp_gro_receive+0x239/0x239 [ 989.919529] ? inet_gro_receive+0x226/0x238 [ 989.919530] __netif_receive_skb+0x4d/0x5f [ 989.919532] netif_receive_skb_internal+0x5c/0xaf [ 989.919533] napi_gro_receive+0x45/0x81 [ 989.919536] ixgbe_poll+0xc8a/0xf09 [ 989.919539] ? kmem_cache_free_bulk+0x1b6/0x1f7 [ 989.919540] net_rx_action+0xf4/0x266 [ 989.919543] __do_softirq+0xa8/0x19d [ 989.919545] irq_exit+0x5d/0x6b [ 989.919546] do_IRQ+0x9c/0xb5 [ 989.919548] common_interrupt+0x93/0x93 [ 989.919548] </IRQ> Similarly dst_clone() can use dst_hold() helper to have additional debugging, as a follow up to commit 44ebe79149ff ("net: add debug atomic_inc_not_zero() in dst_hold()") In net-next we will convert dst atomic_t to refcount_t for peace of mind. Fixes: a4c2fd7f7891 ("net: remove DST_NOCACHE flag") Signed-off-by: Eric Dumazet <[email protected]> Cc: Wei Wang <[email protected]> Reported-by: Paweł Staszewski <[email protected]> Bisected-by: Paweł Staszewski <[email protected]> Acked-by: Wei Wang <[email protected]> Acked-by: Martin KaFai Lau <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-09-21net: phy: Fix truncation of large IRQ numbers in phy_attached_print()Geert Uytterhoeven1-1/+1
Given NR_IRQS is 2048 on sparc64, and even 32784 on alpha, 3 digits is not enough to represent interrupt numbers on all architectures. Hence PHY interrupt numbers may be truncated during printing. Increase the buffer size from 4 to 8 bytes to fix this. Fixes: 5e369aefdce4818c ("net: stmmac: Delete dead code for MDIO registration") Signed-off-by: Geert Uytterhoeven <[email protected]> Reviewed-by: Andrew Lunn <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-09-21Merge branch 'libnvdimm-fixes' of ↵Linus Torvalds2-3/+9
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm Pull libnvdimm fixes from Dan Williams: "A crash fix and corresponding regression test enabling for the crash scenario. The unit test for this crash is available in ndctl-v58.2. This branch has received a build success notification from the 0day-kbuild robot over 148 configs. The fix is tagged for -stable / backport to 4.13" * 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: libnvdimm, namespace: fix btt claim class crash tools/testing/nvdimm: disable labels for nfit_test.1
2017-09-21dt-bindings: clk: stm32h7: fix clock-cell sizeGabriel Fernandez1-1/+1
The clock-cell size is 1 on stm32h7 plaform. Signed-off-by: Gabriel Fernandez <[email protected]> Fixes: 3e4d618b0722 ("clk: stm32h7: Add stm32h743 clock driver") Signed-off-by: Rob Herring <[email protected]>
2017-09-21Input: uinput - avoid crash when sending FF request to device going awayDmitry Torokhov1-18/+21
If FF request comes in while uinput device is going away, uinput_request_send() will fail with -ENODEV, and uinput_request_submit() will attempt to mark the slot as unused by calling uinput_request_done(). Unfortunately in this case we haven't initialized request->done completion yet, and we get a crash: [ 39.402036] BUG: spinlock bad magic on CPU#1, fftest/3108 [ 39.402046] lock: 0xffff88006a93bb00, .magic: 00000000, .owner: /39, .owner_cpu: 1217155072 [ 39.402055] CPU: 1 PID: 3108 Comm: fftest Tainted: G W 4.13.0+ #15 [ 39.402059] Hardware name: LENOVO 20HQS0EG02/20HQS0EG02, BIOS N1MET37W (1.22 ) 07/04/2017 [ 39.402064] 0000000000000086 f0fad82f3ceaa120 ffff88006a93b9a0 ffffffff9de941bb [ 39.402077] ffff88026df8ae00 ffff88006a93bb00 ffff88006a93b9c0 ffffffff9dca62b7 [ 39.402088] ffff88006a93bb00 ffff88006a93baf8 ffff88006a93b9e0 ffffffff9dca62e7 [ 39.402099] Call Trace: [ 39.402112] [<ffffffff9de941bb>] dump_stack+0x4d/0x63 [ 39.402123] [<ffffffff9dca62b7>] spin_dump+0x97/0x9c [ 39.402130] [<ffffffff9dca62e7>] spin_bug+0x2b/0x2d [ 39.402138] [<ffffffff9dca6373>] do_raw_spin_lock+0x28/0xfd [ 39.402147] [<ffffffff9e3055cd>] _raw_spin_lock_irqsave+0x19/0x1f [ 39.402154] [<ffffffff9dca05b7>] complete+0x1d/0x48 [ 39.402162] [<ffffffffc04f30af>] 0xffffffffc04f30af [ 39.402167] [<ffffffffc04f468c>] 0xffffffffc04f468c [ 39.402177] [<ffffffff9dd59c16>] ? __slab_free+0x22f/0x359 [ 39.402184] [<ffffffff9dcc13e9>] ? tk_clock_read+0xc/0xe [ 39.402189] [<ffffffffc04f471f>] 0xffffffffc04f471f [ 39.402195] [<ffffffff9dc9ffe5>] ? __wake_up+0x44/0x4b [ 39.402200] [<ffffffffc04f3240>] ? 0xffffffffc04f3240 [ 39.402207] [<ffffffff9e0f57f3>] erase_effect+0xa1/0xd2 [ 39.402214] [<ffffffff9e0f58c6>] input_ff_flush+0x43/0x5c [ 39.402219] [<ffffffffc04f32ad>] 0xffffffffc04f32ad [ 39.402227] [<ffffffff9e0f174f>] input_flush_device+0x3d/0x51 [ 39.402234] [<ffffffff9e0f69ae>] evdev_flush+0x49/0x5c [ 39.402243] [<ffffffff9dd62d6e>] filp_close+0x3f/0x65 [ 39.402253] [<ffffffff9dd7dcf7>] put_files_struct+0x66/0xc1 [ 39.402261] [<ffffffff9dd7ddeb>] exit_files+0x47/0x4e [ 39.402270] [<ffffffff9dc6b329>] do_exit+0x483/0x969 [ 39.402278] [<ffffffff9dc73211>] ? recalc_sigpending_tsk+0x3d/0x44 [ 39.402285] [<ffffffff9dc6c7a2>] do_group_exit+0x42/0xb0 [ 39.402293] [<ffffffff9dc767e1>] get_signal+0x58d/0x5bf [ 39.402300] [<ffffffff9dc03701>] do_signal+0x37/0x53e [ 39.402307] [<ffffffff9e0f8401>] ? evdev_ioctl_handler+0xac8/0xb04 [ 39.402314] [<ffffffff9e0f8464>] ? evdev_ioctl+0x10/0x12 [ 39.402321] [<ffffffff9dd74cfa>] ? do_vfs_ioctl+0x42e/0x501 [ 39.402328] [<ffffffff9dc0170e>] prepare_exit_to_usermode+0x66/0x90 [ 39.402333] [<ffffffff9dc0181b>] syscall_return_slowpath+0xe3/0xec [ 39.402339] [<ffffffff9e305b7b>] int_ret_from_sys_call+0x25/0x8f While we could solve this by simply initializing the completion earlier, we are better off rearranging the code a bit so we avoid calling complete() on requests that we did not send out. This patch consolidates marking request slots as free in one place (in uinput_request_submit(), the same place where we acquire them) and having everyone else simply signal completion of the requests. Fixes: 00ce756ce53a ("Input: uinput - mark failed submission requests as free") Signed-off-by: Dmitry Torokhov <[email protected]>
2017-09-21Input: uinput - avoid FF flush when destroying deviceDmitry Torokhov3-3/+29
Normally, when input device supporting force feedback effects is being destroyed, we try to "flush" currently playing effects, so that the physical device does not continue vibrating (or executing other effects). Unfortunately this does not work well for uinput as flushing of the effects deadlocks with the destroy action: - if device is being destroyed because the file descriptor is being closed, then there is noone to even service FF requests; - if device is being destroyed because userspace sent UI_DEV_DESTROY, while theoretically it could be possible to service FF requests, userspace is unlikely to do so (they'd need to make sure FF handling happens on a separate thread) even if kernel solves the issue with FF ioctls deadlocking with UI_DEV_DESTROY ioctl on udev->mutex. To avoid lockups like the one below, let's install a custom input device flush handler, and avoid trying to flush force feedback effects when we destroying the device, and instead rely on uinput to shut off the device properly. NMI watchdog: Watchdog detected hard LOCKUP on cpu 3 ... <<EOE>> [<ffffffff817a0307>] _raw_spin_lock_irqsave+0x37/0x40 [<ffffffff810e633d>] complete+0x1d/0x50 [<ffffffffa00ba08c>] uinput_request_done+0x3c/0x40 [uinput] [<ffffffffa00ba587>] uinput_request_submit.part.7+0x47/0xb0 [uinput] [<ffffffffa00bb62b>] uinput_dev_erase_effect+0x5b/0x76 [uinput] [<ffffffff815d91ad>] erase_effect+0xad/0xf0 [<ffffffff815d929d>] flush_effects+0x4d/0x90 [<ffffffff815d4cc0>] input_flush_device+0x40/0x60 [<ffffffff815daf1c>] evdev_cleanup+0xac/0xc0 [<ffffffff815daf5b>] evdev_disconnect+0x2b/0x60 [<ffffffff815d74ac>] __input_unregister_device+0xac/0x150 [<ffffffff815d75f7>] input_unregister_device+0x47/0x70 [<ffffffffa00bac45>] uinput_destroy_device+0xb5/0xc0 [uinput] [<ffffffffa00bb2de>] uinput_ioctl_handler.isra.9+0x65e/0x740 [uinput] [<ffffffff811231ab>] ? do_futex+0x12b/0xad0 [<ffffffffa00bb3f8>] uinput_ioctl+0x18/0x20 [uinput] [<ffffffff81241248>] do_vfs_ioctl+0x298/0x480 [<ffffffff81337553>] ? security_file_ioctl+0x43/0x60 [<ffffffff812414a9>] SyS_ioctl+0x79/0x90 [<ffffffff817a04ee>] entry_SYSCALL_64_fastpath+0x12/0x71 Reported-by: Rodrigo Rivas Costa <[email protected]> Reported-by: Clément VUCHENER <[email protected]> Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=193741 Signed-off-by: Dmitry Torokhov <[email protected]>
2017-09-21Merge branch 'smc-bug-fixes'David S. Miller11-37/+58
Ursula Braun says: ==================== net/smc: bug fixes 2017-09-20 here is a collection of small smc-patches built for net fixing smc problems in different areas. ==================== Signed-off-by: David S. Miller <[email protected]>
2017-09-21net/smc: no close wait in case of process shut downUrsula Braun1-7/+8
Usually socket closing is delayed if there is still data available in the send buffer to be transmitted. If a process is killed, the delay should be avoided. Signed-off-by: Ursula Braun <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-09-21net/smc: introduce a delayUrsula Braun3-10/+16
The number of outstanding work requests is limited. If all work requests are in use, tx processing is postponed to another scheduling of the tx worker. Switch to a delayed worker to have a gap for tx completion queue events before the next retry. Signed-off-by: Ursula Braun <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-09-21net/smc: terminate link group if out-of-sync is receivedUrsula Braun3-11/+8
An out-of-sync condition can just be detected by the client. If the server receives a CLC DECLINE message indicating an out-of-sync condition for the link groups, the server must clean up the out-of-sync link group. There is no need for an extra third parameter in smc_clc_send_decline(). Signed-off-by: Ursula Braun <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-09-21net/smc: longer delay for client link group removalUrsula Braun1-4/+12
Client link group creation always follows the server linkgroup creation. If peer creates a new server link group, client has to create a new client link group. If peer reuses a server link group for a new connection, client has to reuse its client link group as well. This patch introduces a longer delay for client link group removal to make sure this link group still exists, once the peer decides to reuse a server link group. This avoids out-of-sync conditions for link groups. If already scheduled, modify the delay. Signed-off-by: Ursula Braun <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-09-21net/smc: adapt send request completion notificationUrsula Braun1-1/+1
The solicited flag is meaningful for the receive completion queue. Ask for next work completion of any type on the send queue. Signed-off-by: Ursula Braun <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-09-21net/smc: adjust net_device refcountUrsula Braun1-1/+3
smc_pnet_fill_entry() uses dev_get_by_name() adding a refcount to ndev. The following smc_pnet_enter() has to reduce the refcount if the entry to be added exists already in the pnet table. Signed-off-by: Ursula Braun <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-09-21net/smc: take RCU read lock for routing cache lookupUrsula Braun1-3/+7
smc_netinfo_by_tcpsk() looks up the routing cache. Such a lookup requires protection by an RCU read lock. Signed-off-by: Ursula Braun <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-09-21net/smc: add receive timeout checkHans Wippel1-0/+2
The SMC receive function currently lacks a timeout check under the condition that no data were received and no data are available. This patch adds such a check. Signed-off-by: Hans Wippel <[email protected]> Signed-off-by: Ursula Braun <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-09-21net/smc: add missing dev_putHans Wippel1-0/+1
In the infiniband part, SMC currently uses get_netdev which calls dev_hold on the returned net device. However, the SMC code never calls dev_put on that net device resulting in a wrong reference count. This patch adds a dev_put after the usage of the net device to fix the issue. Signed-off-by: Hans Wippel <[email protected]> Signed-off-by: Ursula Braun <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Powered by cgit, Gruvboxed by Blaster4385.