| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The present change is a bug fix for AVB link iteratively up/down.
Steps to reproduce:
- start AVB TX stream (Using aplay via MSE),
- disconnect+reconnect the eth cable,
- after a reconnection the eth connection goes iteratively up/down
without user interaction,
- this may heal after some seconds or even stay for minutes.
As the documentation specifies, the "renesas,no-ether-link" option
should be used when a board does not provide a proper AVB_LINK signal.
There is no need for this option enabled on RCAR H3/M3 Salvator-X/XS
and ULCB starter kits since the AVB_LINK is correctly handled by HW.
Choosing to keep or remove the "renesas,no-ether-link" option will
have impact on the code flow in the following ways:
- keeping this option enabled may lead to unexpected behavior since
the RX & TX are enabled/disabled directly from adjust_link function
without any HW interrogation,
- removing this option, the RX & TX will only be enabled/disabled after
HW interrogation. The HW check is made through the LMON pin in PSR
register which specifies AVB_LINK signal value (0 - at low level;
1 - at high level).
In conclusion, the present change is also a safety improvement because
it removes the "renesas,no-ether-link" option leading to a proper way
of detecting the link state based on HW interrogation and not on
software heuristic.
Fixes: dc36965a8905 ("arm64: dts: r8a7796: salvator-x: Enable EthernetAVB")
Fixes: 6fa501c549aa ("arm64: dts: r8a7795: enable EthernetAVB on Salvator-X")
Signed-off-by: Bogdan Mirea <[email protected]>
Signed-off-by: Vladimir Zapolskiy <[email protected]>
Signed-off-by: Simon Horman <[email protected]>
|
|
pcrypt is using the old way of freeing instances, where the ->free()
method specified in the 'struct crypto_template' is passed a pointer to
the 'struct crypto_instance'. But the crypto_instance is being
kfree()'d directly, which is incorrect because the memory was actually
allocated as an aead_instance, which contains the crypto_instance at a
nonzero offset. Thus, the wrong pointer was being kfree()'d.
Fix it by switching to the new way to free aead_instance's where the
->free() method is specified in the aead_instance itself.
Reported-by: syzbot <[email protected]>
Fixes: 0496f56065e0 ("crypto: pcrypt - Add support for new AEAD interface")
Cc: <[email protected]> # v4.2+
Signed-off-by: Eric Biggers <[email protected]>
Signed-off-by: Herbert Xu <[email protected]>
|
|
queue_cache_init is first called for the Control Word Queue
(n2_crypto_probe). At that time, queue_cache[0] is NULL and a new
kmem_cache will be allocated. If the subsequent n2_register_algs call
fails, the kmem_cache will be released in queue_cache_destroy, but
queue_cache_init[0] is not set back to NULL.
So when the Module Arithmetic Unit gets probed next (n2_mau_probe),
queue_cache_init will not allocate a kmem_cache again, but leave it
as its bogus value, causing a BUG() to trigger when queue_cache[0] is
eventually passed to kmem_cache_zalloc:
n2_crypto: Found N2CP at /virtual-devices@100/n2cp@7
n2_crypto: Registered NCS HVAPI version 2.0
called queue_cache_init
n2_crypto: md5 alg registration failed
n2cp f028687c: /virtual-devices@100/n2cp@7: Unable to register algorithms.
called queue_cache_destroy
n2cp: probe of f028687c failed with error -22
n2_crypto: Found NCP at /virtual-devices@100/ncp@6
n2_crypto: Registered NCS HVAPI version 2.0
called queue_cache_init
kernel BUG at mm/slab.c:2993!
Call Trace:
[0000000000604488] kmem_cache_alloc+0x1a8/0x1e0
(inlined) kmem_cache_zalloc
(inlined) new_queue
(inlined) spu_queue_setup
(inlined) handle_exec_unit
[0000000010c61eb4] spu_mdesc_scan+0x1f4/0x460 [n2_crypto]
[0000000010c62b80] n2_mau_probe+0x100/0x220 [n2_crypto]
[000000000084b174] platform_drv_probe+0x34/0xc0
Cc: <[email protected]>
Signed-off-by: Jan Engelhardt <[email protected]>
Acked-by: David S. Miller <[email protected]>
Signed-off-by: Herbert Xu <[email protected]>
|
|
This variable was increased and decreased without any protection.
Result was an occasional misscount and negative wrap around resulting
in false resource allocation failures.
Fixes: 7d2c3f54e6f6 ("crypto: af_alg - remove locking in async callback")
Signed-off-by: Jonathan Cameron <[email protected]>
Reviewed-by: Stephan Mueller <[email protected]>
Signed-off-by: Herbert Xu <[email protected]>
|
|
If the rfc7539 template was instantiated with a hash algorithm with
digest size larger than 16 bytes (POLY1305_DIGEST_SIZE), then the digest
overran the 'tag' buffer in 'struct chachapoly_req_ctx', corrupting the
subsequent memory, including 'cryptlen'. This caused a crash during
crypto_skcipher_decrypt().
Fix it by, when instantiating the template, requiring that the
underlying hash algorithm has the digest size expected for Poly1305.
Reproducer:
#include <linux/if_alg.h>
#include <sys/socket.h>
#include <unistd.h>
int main()
{
int algfd, reqfd;
struct sockaddr_alg addr = {
.salg_type = "aead",
.salg_name = "rfc7539(chacha20,sha256)",
};
unsigned char buf[32] = { 0 };
algfd = socket(AF_ALG, SOCK_SEQPACKET, 0);
bind(algfd, (void *)&addr, sizeof(addr));
setsockopt(algfd, SOL_ALG, ALG_SET_KEY, buf, sizeof(buf));
reqfd = accept(algfd, 0, 0);
write(reqfd, buf, 16);
read(reqfd, buf, 16);
}
Reported-by: syzbot <[email protected]>
Fixes: 71ebc4d1b27d ("crypto: chacha20poly1305 - Add a ChaCha20-Poly1305 AEAD construction, RFC7539")
Cc: <[email protected]> # v4.2+
Signed-off-by: Eric Biggers <[email protected]>
Signed-off-by: Herbert Xu <[email protected]>
|
|
Without the gf128mul library support, we can run into a link
error:
drivers/crypto/chelsio/chcr_algo.o: In function `chcr_update_tweak':
chcr_algo.c:(.text+0x7e0): undefined reference to `gf128mul_x8_ble'
This adds a Kconfig select statement for it, next to the ones we
already have.
Cc: <[email protected]>
Fixes: b8fd1f4170e7 ("crypto: chcr - Add ctr mode and process large sg entries for cipher")
Signed-off-by: Arnd Bergmann <[email protected]>
Signed-off-by: Herbert Xu <[email protected]>
|
|
dtc points out that the parent node of the interrupt controllers is not
actually an interrupt controller itself, and lacks an #interrupt-cells
property:
arch/arm/boot/dts/tango4-vantage-1172.dtb: Warning (interrupts_property): Missing #interrupt-cells in interrupt-parent /soc/interrupt-controller@6e000
This removes the annotation.
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
dtc warns about two 'clocks' properties that have an extraneous '1'
at the end:
arch/arm/boot/dts/ls1021a-qds.dtb: Warning (clocks_property): arch/arm/boot/dts/ls1021a-twr.dtb: Warning (clocks_property): Property 'clocks', cell 1 is not a phandle reference in /soc/i2c@2180000/mux@77/i2c@4/sgtl5000@2a
arch/arm/boot/dts/ls1021a-qds.dtb: Warning (clocks_property): Missing property '#clock-cells' in node /soc/interrupt-controller@1400000 or bad phandle (referred from /soc/i2c@2180000/mux@77/i2c@4/sgtl5000@2a:clocks[1])
Property 'clocks', cell 1 is not a phandle reference in /soc/i2c@2190000/sgtl5000@a
arch/arm/boot/dts/ls1021a-twr.dtb: Warning (clocks_property): Missing property '#clock-cells' in node /soc/interrupt-controller@1400000 or bad phandle (referred from /soc/i2c@2190000/sgtl5000@a:clocks[1])
The clocks that get referenced here are fixed-rate, so they do not
take any argument, and dtc interprets the next cell as a phandle, which
is invalid.
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
When we migrate a VM from a POWER8 host (XICS) to a POWER9 host
(XICS-on-XIVE), we have an error:
qemu-kvm: Unable to restore KVM interrupt controller state \
(0xff000000) for CPU 0: Invalid argument
This is because kvmppc_xics_set_icp() checks the new state
is internaly consistent, and especially:
...
1129 if (xisr == 0) {
1130 if (pending_pri != 0xff)
1131 return -EINVAL;
...
On the other side, kvmppc_xive_get_icp() doesn't set
neither the pending_pri value, nor the xisr value (set to 0)
(and kvmppc_xive_set_icp() ignores the pending_pri value)
As xisr is 0, pending_pri must be set to 0xff.
Fixes: 5af50993850a ("KVM: PPC: Book3S HV: Native usage of the XIVE interrupt controller")
Cc: [email protected] # v4.12+
Signed-off-by: Laurent Vivier <[email protected]>
Acked-by: Benjamin Herrenschmidt <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
|
|
When restoring a pending interrupt, we are setting the Q bit to force
a retrigger in xive_finish_unmask(). But we also need to force an EOI
in this case to reach the same initial state : P=1, Q=0.
This can be done by not setting 'old_p' for pending interrupts which
will inform xive_finish_unmask() that an EOI needs to be sent.
Fixes: 5af50993850a ("KVM: PPC: Book3S HV: Native usage of the XIVE interrupt controller")
Cc: [email protected] # v4.12+
Suggested-by: Benjamin Herrenschmidt <[email protected]>
Signed-off-by: Cédric Le Goater <[email protected]>
Reviewed-by: Laurent Vivier <[email protected]>
Tested-by: Laurent Vivier <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
|
|
The vk cts test:
dEQP-VK.api.external.semaphore.opaque_fd.export_multiple_times_temporary
triggers a lot of
VFS: Close: file count is 0
Dave pointed out that clearing the syncobj->file from
drm_syncobj_file_release() was sufficient to silence the test, but that
opens a can of worm since we assumed that the syncobj->file was never
unset. Stop trying to reuse the same struct file for every fd pointing
to the drm_syncobj, and allocate one file for each fd instead.
v2: Fixup return handling of drm_syncobj_fd_to_handle
v2.1: [airlied: fix possible syncobj ref race]
Reported-by: Dave Airlie <[email protected]>
Signed-off-by: Chris Wilson <[email protected]>
Tested-by: Dave Airlie <[email protected]>
Reviewed-by: Daniel Vetter <[email protected]>
Signed-off-by: Dave Airlie <[email protected]>
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
drm-misc-fixes before holidays:
- fixup for the lease fixup (Keith)
- fb leak in the ww mutex fallback code (Maarten)
- sun4i fixes (Maxime, Hans)
* tag 'drm-misc-fixes-2017-12-21' of git://anongit.freedesktop.org/drm/drm-misc:
drm: move lease init after validation in drm_lease_create
drm/plane: Make framebuffer refcounting the responsibility of setplane_internal callers
drm/sun4i: hdmi: Move the mode_valid callback to the encoder
drm/sun4i: Fix error path handling
drm/sun4i: validate modes for HDMI
|
|
Pull networking fixes from David Miller"
"What's a holiday weekend without some networking bug fixes? [1]
1) Fix some eBPF JIT bugs wrt. SKB pointers across helper function
calls, from Daniel Borkmann.
2) Fix regression from errata limiting change to marvell PHY driver,
from Zhao Qiang.
3) Fix u16 overflow in SCTP, from Xin Long.
4) Fix potential memory leak during bridge newlink, from Nikolay
Aleksandrov.
5) Fix BPF selftest build on s390, from Hendrik Brueckner.
6) Don't append to cfg80211 automatically generated certs file,
always write new ones from scratch. From Thierry Reding.
7) Fix sleep in atomic in mac80211 hwsim, from Jia-Ju Bai.
8) Fix hang on tg3 MTU change with certain chips, from Brian King.
9) Add stall detection to arc emac driver and reset chip when this
happens, from Alexander Kochetkov.
10) Fix MTU limitng in GRE tunnel drivers, from Xin Long.
11) Fix stmmac timestamping bug due to mis-shifting of field. From
Fredrik Hallenberg.
12) Fix metrics match when deleting an ipv4 route. The kernel sets
some internal metrics bits which the user isn't going to set when
it makes the delete request. From Phil Sutter.
13) mvneta driver loop over RX queues limits on "txq_number" :-) Fix
from Yelena Krivosheev.
14) Fix double free and memory corruption in get_net_ns_by_id, from
Eric W. Biederman.
15) Flush ipv4 FIB tables in the reverse order. Some tables can share
their actual backing data, in particular this happens for the MAIN
and LOCAL tables. We have to kill the LOCAL table first, because
it uses MAIN's backing memory. Fix from Ido Schimmel.
16) Several eBPF verifier value tracking fixes, from Edward Cree, Jann
Horn, and Alexei Starovoitov.
17) Make changes to ipv6 autoflowlabel sysctl really propagate to
sockets, unless the socket has set the per-socket value
explicitly. From Shaohua Li.
18) Fix leaks and double callback invocations of zerocopy SKBs, from
Willem de Bruijn"
[1] Is this a trick question? "Relaxing"? "Quiet"? "Fine"? - Linus.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (77 commits)
skbuff: skb_copy_ubufs must release uarg even without user frags
skbuff: orphan frags before zerocopy clone
net: reevalulate autoflowlabel setting after sysctl setting
openvswitch: Fix pop_vlan action for double tagged frames
ipv6: Honor specified parameters in fibmatch lookup
bpf: do not allow root to mangle valid pointers
selftests/bpf: add tests for recent bugfixes
bpf: fix integer overflows
bpf: don't prune branches when a scalar is replaced with a pointer
bpf: force strict alignment checks for stack pointers
bpf: fix missing error return in check_stack_boundary()
bpf: fix 32-bit ALU op verification
bpf: fix incorrect tracking of register size truncation
bpf: fix incorrect sign extension in check_alu_op()
bpf/verifier: fix bounds calculation on BPF_RSH
ipv4: Fix use-after-free when flushing FIB tables
s390/qeth: fix error handling in checksum cmd callback
tipc: remove joining group member from congested list
selftests: net: Adding config fragment CONFIG_NUMA=y
nfp: bpf: keep track of the offloaded program
...
|
|
Makefile has a LLC variable that is initialised to "llc", but can
theoretically be overridden from the command line ("make LLC=llc-6.0").
However, this fails because for LLVM probe check, "llc" is called
directly. Use the $(LLC) variable instead to fix this.
Fixes: 22c8852624fc ("bpf: improve selftests and add tests for meta pointer")
Signed-off-by: Quentin Monnet <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
Signed-off-by: Daniel Borkmann <[email protected]>
|
|
The locking order of vlan_rwsem (LOCK A) and then rtnl (LOCK B),
contradicts other flows such as ipoib_open possibly causing a deadlock.
To prevent this deadlock heavy flush is called with RTNL locked and
only then tries to acquire vlan_rwsem.
This deadlock is possible only when there are child interfaces.
[ 140.941758] ======================================================
[ 140.946276] WARNING: possible circular locking dependency detected
[ 140.950950] 4.15.0-rc1+ #9 Tainted: G O
[ 140.954797] ------------------------------------------------------
[ 140.959424] kworker/u32:1/146 is trying to acquire lock:
[ 140.963450] (rtnl_mutex){+.+.}, at: [<ffffffffc083516a>] __ipoib_ib_dev_flush+0x2da/0x4e0 [ib_ipoib]
[ 140.970006]
but task is already holding lock:
[ 140.975141] (&priv->vlan_rwsem){++++}, at: [<ffffffffc0834ee1>] __ipoib_ib_dev_flush+0x51/0x4e0 [ib_ipoib]
[ 140.982105]
which lock already depends on the new lock.
[ 140.990023]
the existing dependency chain (in reverse order) is:
[ 140.998650]
-> #1 (&priv->vlan_rwsem){++++}:
[ 141.005276] down_read+0x4d/0xb0
[ 141.009560] ipoib_open+0xad/0x120 [ib_ipoib]
[ 141.014400] __dev_open+0xcb/0x140
[ 141.017919] __dev_change_flags+0x1a4/0x1e0
[ 141.022133] dev_change_flags+0x23/0x60
[ 141.025695] devinet_ioctl+0x704/0x7d0
[ 141.029156] sock_do_ioctl+0x20/0x50
[ 141.032526] sock_ioctl+0x221/0x300
[ 141.036079] do_vfs_ioctl+0xa6/0x6d0
[ 141.039656] SyS_ioctl+0x74/0x80
[ 141.042811] entry_SYSCALL_64_fastpath+0x1f/0x96
[ 141.046891]
-> #0 (rtnl_mutex){+.+.}:
[ 141.051701] lock_acquire+0xd4/0x220
[ 141.055212] __mutex_lock+0x88/0x970
[ 141.058631] __ipoib_ib_dev_flush+0x2da/0x4e0 [ib_ipoib]
[ 141.063160] __ipoib_ib_dev_flush+0x71/0x4e0 [ib_ipoib]
[ 141.067648] process_one_work+0x1f5/0x610
[ 141.071429] worker_thread+0x4a/0x3f0
[ 141.074890] kthread+0x141/0x180
[ 141.078085] ret_from_fork+0x24/0x30
[ 141.081559]
other info that might help us debug this:
[ 141.088967] Possible unsafe locking scenario:
[ 141.094280] CPU0 CPU1
[ 141.097953] ---- ----
[ 141.101640] lock(&priv->vlan_rwsem);
[ 141.104771] lock(rtnl_mutex);
[ 141.109207] lock(&priv->vlan_rwsem);
[ 141.114032] lock(rtnl_mutex);
[ 141.116800]
*** DEADLOCK ***
Fixes: b4b678b06f6e ("IB/ipoib: Grab rtnl lock on heavy flush when calling ndo_open/stop")
Signed-off-by: Alex Vesker <[email protected]>
Signed-off-by: Leon Romanovsky <[email protected]>
Signed-off-by: Jason Gunthorpe <[email protected]>
|
|
Congestion counters are counted and queried per physical function.
When working in LAG mode, CNP packets can be sent or received on both
of the functions, thus congestion counters should be aggregated from
the two physical functions.
Fixes: e1f24a79f424 ("IB/mlx5: Support congestion related counters")
Signed-off-by: Majd Dibbiny <[email protected]>
Reviewed-by: Aviv Heller <[email protected]>
Signed-off-by: Leon Romanovsky <[email protected]>
Signed-off-by: Jason Gunthorpe <[email protected]>
|
|
The use of wait queues in vmw_pvrdma for handling concurrent
access to a resource leaves a race condition which can cause a use
after free bug.
Fix this by using the pattern from other drivers, complete() protected by
dec_and_test to ensure complete() is called only once.
Fixes: 29c8d9eba550 ("IB: Add vmw_pvrdma driver")
Signed-off-by: Bryan Tan <[email protected]>
Signed-off-by: Jason Gunthorpe <[email protected]>
|
|
refcount_dec generates a warning when the operation
causes the refcount to hit zero. Avoid this by using
refcount_dec_and_test.
Fixes: 8b10ba783c9d ("RDMA/vmw_pvrdma: Add shared receive queue support")
Reviewed-by: Adit Ranadive <[email protected]>
Reviewed-by: Aditya Sarwade <[email protected]>
Reviewed-by: Jorgen Hansen <[email protected]>
Signed-off-by: Bryan Tan <[email protected]>
Reviewed-by: Leon Romanovsky <[email protected]>
Signed-off-by: Jason Gunthorpe <[email protected]>
|
|
The QP cleanup did not previously call ib_umem_release,
resulting in a user-triggerable kernel resource leak.
Fixes: 29c8d9eba550 ("IB: Add vmw_pvrdma driver")
Reviewed-by: Adit Ranadive <[email protected]>
Reviewed-by: Aditya Sarwade <[email protected]>
Reviewed-by: Jorgen Hansen <[email protected]>
Signed-off-by: Bryan Tan <[email protected]>
Signed-off-by: Jason Gunthorpe <[email protected]>
|
|
If a wr chain was posted and needed to be flushed, only the first
wr in the chain was completed with FLUSHED status. The rest were
never completed. This caused isert to hang on shutdown due to the
missing completions which left iscsi IO commands referenced, stalling
the shutdown.
Fixes: 4fe7c2962e11 ("iw_cxgb4: refactor sq/rq drain logic")
Cc: [email protected]
Signed-off-by: Steve Wise <[email protected]>
Signed-off-by: Jason Gunthorpe <[email protected]>
|
|
The flush/drain logic was not retaining the original wr opcode in
its completion. This can cause problems if the application uses
the completion opcode to make decisions.
Use bit 10 of the CQE header word to indicate the CQE is a special
drain completion, and save the original WR opcode in the cqe header
opcode field.
Fixes: 4fe7c2962e11 ("iw_cxgb4: refactor sq/rq drain logic")
Cc: [email protected]
Signed-off-by: Steve Wise <[email protected]>
Signed-off-by: Jason Gunthorpe <[email protected]>
|
|
If the RECV CQE is in error, ignore the MSN check. This was causing
recvs that were flushed into the sw cq to be completed with the wrong
status (BAD_MSN instead of FLUSHED).
Cc: [email protected]
Signed-off-by: Steve Wise <[email protected]>
Signed-off-by: Jason Gunthorpe <[email protected]>
|
|
Due to a spec misinterpretation, the Linux implementation of the BTT log
area had different padding scheme from other implementations, such as
UEFI and NVML.
This fixes the padding scheme, and defaults to it for new BTT layouts.
We attempt to detect the padding scheme in use when probing for an
existing BTT. If we detect the older/incompatible scheme, we continue
using it.
Reported-by: Juston Li <[email protected]>
Cc: Dan Williams <[email protected]>
Cc: <[email protected]>
Fixes: 5212e11fde4d ("nd_btt: atomic sector updates")
Signed-off-by: Vishal Verma <[email protected]>
Signed-off-by: Dan Williams <[email protected]>
|
|
Recent updates to btt.h neglected to add corresponding kernel-doc lines
for new structure members. Add them.
Signed-off-by: Vishal Verma <[email protected]>
Signed-off-by: Dan Williams <[email protected]>
|
|
Saeed Mahameed says:
===================
Mellanox, mlx5 fixes 2017-12-19
The follwoing series includes some fixes for mlx5 core and etherent
driver.
Please pull and let me know if there is any problem.
This series doesn't introduce any conflict with the ongoing mlx5 for-next
submission.
For -stable:
kernels >= v4.7.y
("net/mlx5e: Fix possible deadlock of VXLAN lock")
("net/mlx5e: Add refcount to VXLAN structure")
("net/mlx5e: Prevent possible races in VXLAN control flow")
("net/mlx5e: Fix features check of IPv6 traffic")
kernels >= v4.9.y
("net/mlx5: Fix error flow in CREATE_QP command")
("net/mlx5: Fix rate limit packet pacing naming and struct")
kernels >= v4.13.y
("net/mlx5: FPGA, return -EINVAL if size is zero")
kernels >= v4.14.y
("Revert "mlx5: move affinity hints assignments to generic code")
All above patches apply and compile with no issues on corresponding -stable.
===================
Signed-off-by: David S. Miller <[email protected]>
|
|
skb_copy_ubufs creates a private copy of frags[] to release its hold
on user frags, then calls uarg->callback to notify the owner.
Call uarg->callback even when no frags exist. This edge case can
happen when zerocopy_sg_from_iter finds enough room in skb_headlen
to copy all the data.
Fixes: 3ece782693c4 ("sock: skb_copy_ubufs support for compound pages")
Signed-off-by: Willem de Bruijn <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Call skb_zerocopy_clone after skb_orphan_frags, to avoid duplicate
calls to skb_uarg(skb)->callback for the same data.
skb_zerocopy_clone associates skb_shinfo(skb)->uarg from frag_skb
with each segment. This is only safe for uargs that do refcounting,
which is those that pass skb_orphan_frags without dropping their
shared frags. For others, skb_orphan_frags drops the user frags and
sets the uarg to NULL, after which sock_zerocopy_clone has no effect.
Qemu hangs were reported due to duplicate vhost_net_zerocopy_callback
calls for the same data causing the vhost_net_ubuf_ref_>refcount to
drop below zero.
Link: http://lkml.kernel.org/r/<CAF=yD-LWyCD4Y0aJ9O0e_CHLR+3JOeKicRRTEVCPxgw4XOcqGQ@mail.gmail.com>
Fixes: 1f8b977ab32d ("sock: enable MSG_ZEROCOPY")
Reported-by: Andreas Hartmann <[email protected]>
Reported-by: David Hill <[email protected]>
Signed-off-by: Willem de Bruijn <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Pull block fixes from Jens Axboe:
"It's been a few weeks, so here's a small collection of fixes that
should go into the current series.
This contains:
- NVMe pull request from Christoph, with a few important fixes.
- kyber hang fix from Omar.
- A blk-throttl fix from Shaohua, fixing a case where we double
charge a bio.
- Two call_single_data alignment fixes from me, fixing up some
unfortunate changes that went into 4.14 without being properly
reviewed on the block side (since nobody was CC'ed on the
patch...).
- A bounce buffer fix in two parts, one from me and one from Ming.
- Revert bdi debug error handling patch. It's causing boot issues for
some folks, and a week down the line, we're still no closer to a
fix. Revert this patch for now until it's figured out, then we can
retry for 4.16"
* 'for-linus' of git://git.kernel.dk/linux-block:
Revert "bdi: add error handle for bdi_debug_register"
null_blk: unalign call_single_data
block: unalign call_single_data in struct request
block-throttle: avoid double charge
block: fix blk_rq_append_bio
block: don't let passthrough IO go into .make_request_fn()
nvme: setup streams after initializing namespace head
nvme: check hw sectors before setting chunk sectors
nvme: call blk_integrity_unregister after queue is cleaned up
nvme-fc: remove double put reference if admin connect fails
nvme: set discard_alignment to zero
kyber: fix another domain token wait queue hang
|
|
Pull KVM fixes from Paolo Bonzini:
"ARM fixes:
- A bug in handling of SPE state for non-vhe systems
- A fix for a crash on system shutdown
- Three timer fixes, introduced by the timer optimizations for v4.15
x86 fixes:
- fix for a WARN that was introduced in 4.15
- fix for SMM when guest uses PCID
- fixes for several bugs found by syzkaller
... and a dozen papercut fixes for the kvm_stat tool"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (22 commits)
tools/kvm_stat: sort '-f help' output
kvm: x86: fix RSM when PCID is non-zero
KVM: Fix stack-out-of-bounds read in write_mmio
KVM: arm/arm64: Fix timer enable flow
KVM: arm/arm64: Properly handle arch-timer IRQs after vtimer_save_state
KVM: arm/arm64: timer: Don't set irq as forwarded if no usable GIC
KVM: arm/arm64: Fix HYP unmapping going off limits
arm64: kvm: Prevent restoring stale PMSCR_EL1 for vcpu
KVM/x86: Check input paging mode when cs.l is set
tools/kvm_stat: add line for totals
tools/kvm_stat: stop ignoring unhandled arguments
tools/kvm_stat: suppress usage information on command line errors
tools/kvm_stat: handle invalid regular expressions
tools/kvm_stat: add hint on '-f help' to man page
tools/kvm_stat: fix child trace events accounting
tools/kvm_stat: fix extra handling of 'help' with fields filter
tools/kvm_stat: fix missing field update after filter change
tools/kvm_stat: fix drilldown in events-by-guests mode
tools/kvm_stat: fix command line option '-g'
kvm: x86: fix WARN due to uninitialized guest FPU state
...
|
|
sysctl.ip6.auto_flowlabels is default 1. In our hosts, we set it to 2.
If sockopt doesn't set autoflowlabel, outcome packets from the hosts are
supposed to not include flowlabel. This is true for normal packet, but
not for reset packet.
The reason is ipv6_pinfo.autoflowlabel is set in sock creation. Later if
we change sysctl.ip6.auto_flowlabels, the ipv6_pinfo.autoflowlabel isn't
changed, so the sock will keep the old behavior in terms of auto
flowlabel. Reset packet is suffering from this problem, because reset
packet is sent from a special control socket, which is created at boot
time. Since sysctl.ipv6.auto_flowlabels is 1 by default, the control
socket will always have its ipv6_pinfo.autoflowlabel set, even after
user set sysctl.ipv6.auto_flowlabels to 1, so reset packset will always
have flowlabel. Normal sock created before sysctl setting suffers from
the same issue. We can't even turn off autoflowlabel unless we kill all
socks in the hosts.
To fix this, if IPV6_AUTOFLOWLABEL sockopt is used, we use the
autoflowlabel setting from user, otherwise we always call
ip6_default_np_autolabel() which has the new settings of sysctl.
Note, this changes behavior a little bit. Before commit 42240901f7c4
(ipv6: Implement different admin modes for automatic flow labels), the
autoflowlabel behavior of a sock isn't sticky, eg, if sysctl changes,
existing connection will change autoflowlabel behavior. After that
commit, autoflowlabel behavior is sticky in the whole life of the sock.
With this patch, the behavior isn't sticky again.
Cc: Martin KaFai Lau <[email protected]>
Cc: Eric Dumazet <[email protected]>
Cc: Tom Herbert <[email protected]>
Signed-off-by: Shaohua Li <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
skb_vlan_pop() expects skb->protocol to be a valid TPID for double
tagged frames. So set skb->protocol to the TPID and let skb_vlan_pop()
shift the true ethertype into position for us.
Fixes: 5108bbaddc37 ("openvswitch: add processing of L3 packets")
Signed-off-by: Eric Garver <[email protected]>
Reviewed-by: Jiri Benc <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Current code advertises (on the modifiers blob property) support for CCS
modifier for pipe C on GLK, only to reject it later when validating the
request before the atomic commit.
This fixes the tests igt@kms_ccs@pipe-c-*, which should skip on GLK for
pipe C (see bug 104096).
A relevant discussion is archived at:
https://lists.freedesktop.org/archives/intel-gfx/2017-December/150646.html
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104096
Signed-off-by: Gabriel Krisman Bertazi <[email protected]>
Cc: Ben Widawsky <[email protected]>
Reviewed-by: Ben Widawsky <[email protected]>
Signed-off-by: Rodrigo Vivi <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
(cherry picked from commit f0cbd8bd877f3d8c5b80a6b1add9ca9010d7f9d8)
Signed-off-by: Jani Nikula <[email protected]>
|
|
This reverts commit a0747a859ef6d3cc5b6cd50eb694499b78dd0025.
It breaks some booting for some users, and more than a week
into this, there's still no good fix. Revert this commit
for now until a solution has been found.
Reported-by: Laura Abbott <[email protected]>
Reported-by: Bruno Wolff III <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
Currently, parameters such as oif and source address are not taken into
account during fibmatch lookup. Example (IPv4 for reference) before
patch:
$ ip -4 route show
192.0.2.0/24 dev dummy0 proto kernel scope link src 192.0.2.1
198.51.100.0/24 dev dummy1 proto kernel scope link src 198.51.100.1
$ ip -6 route show
2001:db8:1::/64 dev dummy0 proto kernel metric 256 pref medium
2001:db8:2::/64 dev dummy1 proto kernel metric 256 pref medium
fe80::/64 dev dummy0 proto kernel metric 256 pref medium
fe80::/64 dev dummy1 proto kernel metric 256 pref medium
$ ip -4 route get fibmatch 192.0.2.2 oif dummy0
192.0.2.0/24 dev dummy0 proto kernel scope link src 192.0.2.1
$ ip -4 route get fibmatch 192.0.2.2 oif dummy1
RTNETLINK answers: No route to host
$ ip -6 route get fibmatch 2001:db8:1::2 oif dummy0
2001:db8:1::/64 dev dummy0 proto kernel metric 256 pref medium
$ ip -6 route get fibmatch 2001:db8:1::2 oif dummy1
2001:db8:1::/64 dev dummy0 proto kernel metric 256 pref medium
After:
$ ip -6 route get fibmatch 2001:db8:1::2 oif dummy0
2001:db8:1::/64 dev dummy0 proto kernel metric 256 pref medium
$ ip -6 route get fibmatch 2001:db8:1::2 oif dummy1
RTNETLINK answers: Network is unreachable
The problem stems from the fact that the necessary route lookup flags
are not set based on these parameters.
Instead of duplicating the same logic for fibmatch, we can simply
resolve the original route from its copy and dump it instead.
Fixes: 18c3a61c4264 ("net: ipv6: RTM_GETROUTE: return matched fib result when requested")
Signed-off-by: Ido Schimmel <[email protected]>
Acked-by: David Ahern <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
For rmap removal, refactor the rmap owner checks into a separate
function, then skip the checks if we are performing an unknown-owner
removal.
Signed-off-by: Darrick J. Wong <[email protected]>
Reviewed-by: Christoph Hellwig <[email protected]>
|
|
Calling xfs_rmap_free with an unknown owner is supposed to remove any
rmaps covering that range regardless of owner. This is used by the EFI
recovery code to say "we're freeing this, it mustn't be owned by
anything anymore", but for whatever reason xfs_free_ag_extent filters
them out.
Therefore, remove the filter and make xfs_rmap_unmap actually treat it
as a wildcard owner -- free anything that's already there, and if
there's no owner at all then that's fine too.
There are two existing callers of bmap_add_free that take care the rmap
deferred ops themselves and use OWN_UNKNOWN to skip the EFI-based rmap
cleanup; convert these to use OWN_NULL (via helpers), and now we really
require that an RUI (if any) gets added to the defer ops before any EFI.
Lastly, now that xfs_free_extent filters out OWN_NULL rmap free requests,
growfs will have to consult directly with the rmap to ensure that there
aren't any rmaps in the grown region.
Signed-off-by: Darrick J. Wong <[email protected]>
Reviewed-by: Christoph Hellwig <[email protected]>
|
|
order
Under the deferred rmap operation scheme, there's a certain order in
which the rmap deferred ops have to be queued to maintain integrity
during log replay. For alloc/map operations that order is cui -> rui;
for free/unmap operations that order is cui -> rui -> efi. However, the
initial refcount code got the ordering wrong in the free side of things
because it queued refcount free op and an EFI and the refcount free op
queued a rmap free op, resulting in the order cui -> efi -> rui.
If we fail before the efd finishes, the efi recovery will try to do a
wildcard rmap removal and the subsequent rui will fail to find the rmap
and blow up. This didn't ever happen due to other screws up in handling
unknown owner rmap removals, but those other screw ups broke recovery in
other ways, so fix the ordering to follow the intended rules.
Signed-off-by: Darrick J. Wong <[email protected]>
Reviewed-by: Christoph Hellwig <[email protected]>
|
|
If a user performs a direct CoW write, we end up loading the CoW fork
with preallocated extents. Therefore, we must set the cowblocks tag so
that they can be cleared out if we run low on space.
Signed-off-by: Darrick J. Wong <[email protected]>
Reviewed-by: Dave Chinner <[email protected]>
Reviewed-by: Christoph Hellwig <[email protected]>
|
|
When we're remounting the filesystem readonly, remove all CoW
preallocations prior to going ro. If the fs goes down after the ro
remount, we never clean up the staging extents, which means xfs_check
will trip over them on a subsequent run. Practically speaking, the next
mount will clean them up too, so this is unlikely to be seen. Since we
shut down the cowblocks cleaner on remount-ro, we also have to make sure
we start it back up if/when we remount-rw.
Found by adding clonerange to fsstress and running xfs/017.
Signed-off-by: Darrick J. Wong <[email protected]>
Reviewed-by: Dave Chinner <[email protected]>
Reviewed-by: Christoph Hellwig <[email protected]>
|
|
Currently, xfs_itruncate_extents clears the cowblocks tag if i_cnextents
is zero. This is wrong, since i_cnextents only tracks real extents in
the CoW fork, which means that we could have some delayed CoW
reservations still in there that will now never get cleaned.
Fix a further bug where we /don't/ clear the reflink iflag if there are
any attribute blocks -- really, it's only safe to clear the reflink flag
if there are no data fork extents and no cow fork extents.
Found by adding clonerange to fsstress in xfs/017.
Signed-off-by: Darrick J. Wong <[email protected]>
Reviewed-by: Dave Chinner <[email protected]>
Reviewed-by: Christoph Hellwig <[email protected]>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into fixes
Pull "TI DaVinci fixes for v4.15" from Sekhar Nori:
DaVinci fixes for v4.15 consiting of fixes to make EDMA and MMC/SD
work on DM365 and a fix for battery voltage monitoring on Lego EV3.
* tag 'davinci-fixes-for-v4.15' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: fix mmc entries in dm365's dma_slave_map
ARM: dts: da850-lego-ev3: Fix battery voltage gpio
ARM: davinci: Add dma_mask to dm365's eDMA device
ARM: davinci: Use platform_device_register_full() to create pdev for dm365's eDMA
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into fixes
Pull "Fixes for 4.15:" from Alexandre Belloni:
- tse850-3: fix an i2c timeout issue
* tag 'at91-ab-4.15-dt-fixes' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: dts: at91: disable the nxp,se97b SMBUS timeout on the TSE-850
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes
Pull "Rockchip dts64 fixes for 4.15" from Heiko Stübner:
Another trailing interrupt-cell 0 removed.
Removed as well got the vdd_log regulator from the rk3399-puma board.
While it is there, the absence of any user makes it prone to configuration
problems when the pwm-regulator takes over the boot-up default and wiggles
settings there. Case in question was the PCIe host not working anymore.
With vdd_log removed for the time being, PCIe on Puma works again.
And a second stopgap is limiting the speed of the gmac on the rk3328-rock64
to 100MBit. While the hardware can reach 1GBit, currently it is not stable.
Limiting it to 100MBit for the time being allows nfsroots to be used again
until the problem is identified.
* tag 'v4.15-rockchip-dts64fixes-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: limit rk3328-rock64 gmac speed to 100MBit for now
arm64: dts: rockchip: remove vdd_log from rk3399-puma
arm64: dts: rockchip: fix trailing 0 in rk3328 tsadc interrupts
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes
Pull "Rockchip dts32 fixes for 4.15" from Heiko Stübner:
Removed another trailing interrupt-cell 0 and added the cpu regulator
on the rk3066a-marsboard to make it not fail from cpufreq changes.
* tag 'v4.15-rockchip-dts32fixes-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: fix rk3288 iep-IOMMU interrupts property cells
ARM: dts: rockchip: add cpu0-regulator on rk3066a-marsboard
|
|
This should have always been 8.
Fixes: db4d6d9d80fa ("ARM: dts: aspeed: Correctly order UART nodes")
Cc: [email protected]
Signed-off-by: Joel Stanley <[email protected]>
Reviewed-by: Cédric Le Goater <[email protected]>
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
Commit 1cb686c08d12 ("ARM: dts: exynos: Add status property to Exynos 542x
Mixer nodes") disabled the Mixer node by default in the DTSI and enabled
for each Exynos 542x DTS. But unfortunately it missed to enable it for the
Exynos5800 Peach Pi machine, since the 5800 is also an 542x SoC variant.
Fixes: 1cb686c08d12 ("ARM: dts: exynos: Add status property to Exynos 542x Mixer nodes")
Signed-off-by: Javier Martinez Canillas <[email protected]>
Acked-by: Marek Szyprowski <[email protected]>
Tested-by: Guillaume Tucker <[email protected]>
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
Sort the fields returned by specifying '-f help' on the command line.
While at it, simplify the code a bit, indent the output and eliminate an
extra blank line at the beginning.
Signed-off-by: Stefan Raspl <[email protected]>
Signed-off-by: Paolo Bonzini <[email protected]>
|
|
rsm_load_state_64() and rsm_enter_protected_mode() load CR3, then
CR4 & ~PCIDE, then CR0, then CR4.
However, setting CR4.PCIDE fails if CR3[11:0] != 0. It's probably easier
in the long run to replace rsm_enter_protected_mode() with an emulator
callback that sets all the special registers (like KVM_SET_SREGS would
do). For now, set the PCID field of CR3 only after CR4.PCIDE is 1.
Reported-by: Laszlo Ersek <[email protected]>
Tested-by: Laszlo Ersek <[email protected]>
Fixes: 660a5d517aaab9187f93854425c4c63f4a09195c
Cc: [email protected]
Signed-off-by: Paolo Bonzini <[email protected]>
|
|
drm-intel-fixes
gvt-fixes-2017-12-21:
- default pipe enable fix for virtual display (Xiaolin)
Signed-off-by: Jani Nikula <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
We added support for EXTPROC back in 2010 in commit 26df6d13406d ("tty:
Add EXTPROC support for LINEMODE") and the intent was to allow it to
override some (all?) ICANON behavior. Quoting from that original commit
message:
There is a new bit in the termios local flag word, EXTPROC.
When this bit is set, several aspects of the terminal driver
are disabled. Input line editing, character echo, and mapping
of signals are all disabled. This allows the telnetd to turn
off these functions when in linemode, but still keep track of
what state the user wants the terminal to be in.
but the problem turns out that "several aspects of the terminal driver
are disabled" is a bit ambiguous, and you can really confuse the n_tty
layer by setting EXTPROC and then causing some of the ICANON invariants
to no longer be maintained.
This fixes at least one such case (TIOCINQ) becoming unhappy because of
the confusion over whether ICANON really means ICANON when EXTPROC is set.
This basically makes TIOCINQ match the case of read: if EXTPROC is set,
we ignore ICANON. Also, make sure to reset the ICANON state ie EXTPROC
changes, not just if ICANON changes.
Fixes: 26df6d13406d ("tty: Add EXTPROC support for LINEMODE")
Reported-by: Tetsuo Handa <[email protected]>
Reported-by: syzkaller <[email protected]>
Cc: Jiri Slaby <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|