| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
During initial submission the selection of the channel was done using
the scan_index member of the iio_chan_spec structure. It was an abuse
because this member is supposed to be used with a buffer so it was
removed.
However there was still the need to be able to known how to select a
channel, the correct member to store this information is address.
Thanks to this it is possible to select any other channel than the
channel 0.
Fixes: 8dd2d7c0fed7 ("iio: adc: Add driver for the TI ADS8344 A/DC chips")
Signed-off-by: Gregory CLEMENT <[email protected]>
Cc: <[email protected]>
Signed-off-by: Jonathan Cameron <[email protected]>
|
|
If the serial interface is used, the 8-bit address should be latched using
the rising edge of the WR/FSYNC signal.
This basically means that a CS change is required between the first byte
sent, and the second one.
This change splits the single-transfer transfer of 2 bytes into 2 transfers
with a single byte, and CS change in-between.
Note fixes tag is not accurate, but reflects a point beyond which there
are too many refactors to make backporting straight forward.
Fixes: b19e9ad5e2cb ("staging:iio:resolver:ad2s1210 general driver cleanup.")
Signed-off-by: Dragos Bogdan <[email protected]>
Signed-off-by: Alexandru Ardelean <[email protected]>
Cc: <[email protected]>
Signed-off-by: Jonathan Cameron <[email protected]>
|
|
A call to 'vf610_dac_exit()' is missing in an error handling path.
Fixes: 1b983bf42fad ("iio: dac: vf610_dac: Add IIO DAC driver for Vybrid SoC")
Signed-off-by: Christophe JAILLET <[email protected]>
Cc: <[email protected]>
Signed-off-by: Jonathan Cameron <[email protected]>
|
|
We need to release a lock if st_lsm6dsx_check_odr() fails, we can't
return directly.
Fixes: 76551a3c3df1 ("iio: imu: st_lsm6dsx: specify slave odr in slv_odr")
Signed-off-by: Dan Carpenter <[email protected]>
Signed-off-by: Jonathan Cameron <[email protected]>
|
|
IIO_CONCENTRATION channel for the DO-SM shouldn't be indexed as
there isn't more than one, and also ATLAS_CONCENTRATION_CHANNEL
macro scan_index define steps on the IIO_TIMESTAMP channel.
Signed-off-by: Matt Ranostay <[email protected]>
Fixes: a751b8e48018 (iio: chemical: atlas-sensor: add DO-SM module support)
Signed-off-by: Jonathan Cameron <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 5.7 cycle.
Includes one MAINTAINERS update to avoid people getting a lot of bounce
messages and complaining about it.
* MAINTAINERS
- Drop Stefan Popa's Analog Devices email address in favour of
Michael Hennerich.
* core
- Fix handling of dB sysfs inputs.
- Drop a stray semi colon in macro definition.
* ad5770r
- Fix an off by one in chec on maximum number of channels.
* ad7192
- Fix a null pointer de-reference due to the name previously being
retrieved from the spi_get_device_id call which no longer works as
the relevant table was removed.
* ad7797
- Use correct attribute group.
* counter/104-quad-8
- Add locks to prevent some race conditions.
* inv-mpu6050
- Fix issues around suspend / resume clashing with runtime PM.
* stm32-adc
- Fix sleep in invalid context
- Fix id relative path error in device tree binding doc.
* st_lsm6dsx
- Fix a read alignment issue on an untagged FIFO.
- Handle odr for slave to properly compute the FIFO data layout / pattern.
- Flush the HW FIFO before resettting the device to avoid a race on
interrupt line 1.
* st_sensors
- Rely on ODR mask not ODR address to identify if the ODR can be set.
Some devices have an ODR address of 0.
* ti-ads8344
- Byte ordering was wrong - fix it.
* xilinx-xadc
- Fix inverted logic in powering down the second ADC.
- Fix clearing interrupt when enabling the trigger.
- Fix configuration of sequencer when in simultaneous sampling mode.
- Limit initial sampling rate as done for runtime configured ones.
* tag 'iio-fixes-for-5.7a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
MAINTAINERS: remove Stefan Popa's email
iio: adc: ad7192: fix null pointer de-reference crash during probe
iio: core: remove extra semi-colon from devm_iio_device_register() macro
iio: adc: ti-ads8344: properly byte swap value
iio: imu: inv_mpu6050: fix suspend/resume with runtime power
iio: st_sensors: rely on odr mask to know if odr can be set
iio: xilinx-xadc: Make sure not exceed maximum samplerate
iio: xilinx-xadc: Fix sequencer configuration for aux channels in simultaneous mode
iio: xilinx-xadc: Fix clearing interrupt when enabling trigger
iio: xilinx-xadc: Fix ADC-B powerdown
iio: dac: ad5770r: fix off-by-one check on maximum number of channels
iio: imu: st_lsm6dsx: flush hw FIFO before resetting the device
iio: core: Fix handling of 'dB'
dt-bindings: iio: adc: stm32-adc: fix id relative path
counter: 104-quad-8: Add lock guards - generic interface
iio: imu: st_lsm6dsx: specify slave odr in slv_odr
iio: imu: st_lsm6dsx: fix read misalignment on untagged FIFO
iio: adc: stm32-adc: fix sleep in atomic context
iio:ad7797: Use correct attribute_group
|
|
The email is no longer active. This change removes Stefan's email from the
MAINTAINERS list and replaces it with Michael Hennerich's.
Signed-off-by: Michael Hennerich <[email protected]>
Signed-off-by: Alexandru Ardelean <[email protected]>
Signed-off-by: Jonathan Cameron <[email protected]>
|
|
When the 'spi_device_id' table was removed, it omitted to cleanup/fix the
assignment:
'indio_dev->name = spi_get_device_id(spi)->name;'
After that patch 'spi_get_device_id(spi)' returns NULL, so this crashes
during probe with null de-ref.
This change fixes this by introducing an ad7192_chip_info struct, and
defines all part-names [that should be assigned to indio_dev->name] in a
'ad7192_chip_info_tbl' table.
With this change, the old 'st->devid' is also moved to be a
'chip_info->chip_id'. And the old 'ID_AD719X' macros have been renamed to
'CHIPID_AD719X'. Tld identifiers have been re-purposed to be enum/index
values in the new 'ad7192_chip_info_tbl'.
This should fix the bug, and maintain the ABI for the 'indio_dev->name'
field.
Fixes: 66614ab2be38 ("staging: iio: adc: ad7192: removed spi_device_id")
Signed-off-by: Alexandru Ardelean <[email protected]>
Signed-off-by: Jonathan Cameron <[email protected]>
|
|
This change removes the semi-colon from the devm_iio_device_register()
macro which seems to have been added by accident.
Fixes: 63b19547cc3d9 ("iio: Use macro magic to avoid manual assign of driver_module")
Signed-off-by: Lars Engebretsen <[email protected]>
Cc: <[email protected]>
Reviewed-by: Alexandru Ardelean <[email protected]>
Signed-off-by: Jonathan Cameron <[email protected]>
|
|
The first received byte is the MSB, followed by the LSB so the value needs
to be byte swapped.
Also, the ADC actually has a delay of one clock on the SPI bus. Read three
bytes to get the last bit.
Fixes: 8dd2d7c0fed7 ("iio: adc: Add driver for the TI ADS8344 A/DC chips")
Signed-off-by: Alexandre Belloni <[email protected]>
Cc: <[email protected]>
Signed-off-by: Jonathan Cameron <[email protected]>
|
|
Suspend/resume were not working correctly with pm runtime.
Now suspend check if the chip is already suspended, and
resume put runtime pm in the correct state.
Issues seen prior to this were:
When entering suspend, there was an error in logs because we
were disabling vddio regulator although it was already disabled.
And when resuming, the chip was pull back to full power but the
pm_runtime state was not updated. So it was believing it was
still suspended.
Fixes: 4599cac84614 ("iio: imu: inv_mpu6050: use runtime pm with autosuspend")
Signed-off-by: Jean-Baptiste Maneyrol <[email protected]>
Signed-off-by: Jonathan Cameron <[email protected]>
|
|
Indeed, relying on addr being not 0 cannot work because some device have
their register to set odr at address 0. As a matter of fact, if the odr
can be set, then there is a mask.
Sensors with ODR register at address 0 are: lsm303dlh, lsm303dlhc, lsm303dlm
Fixes: 7d245172675a ("iio: common: st_sensors: check odr address value in st_sensors_set_odr()")
Signed-off-by: Lary Gibaud <[email protected]>
Cc: <[email protected]>
Signed-off-by: Jonathan Cameron <[email protected]>
|
|
The XADC supports a samplerate of up to 1MSPS. Unfortunately the hardware
does not have a FIFO, which means it generates an interrupt for each
conversion sequence. At one 1MSPS this creates an interrupt storm that
causes the system to soft-lock.
For this reason the driver limits the maximum samplerate to 150kSPS.
Currently this check is only done when setting a new samplerate. But it is
also possible that the initial samplerate configured in the FPGA bitstream
exceeds the limit.
In this case when starting to capture data without first changing the
samplerate the system can overload.
To prevent this check the currently configured samplerate in the probe
function and reduce it to the maximum if necessary.
Signed-off-by: Lars-Peter Clausen <[email protected]>
Fixes: bdc8cda1d010 ("iio:adc: Add Xilinx XADC driver")
Cc: <[email protected]>
Signed-off-by: Jonathan Cameron <[email protected]>
|
|
simultaneous mode
The XADC has two internal ADCs. Depending on the mode it is operating in
either one or both of them are used. The device manual calls this
continuous (one ADC) and simultaneous (both ADCs) mode.
The meaning of the sequencing register for the aux channels changes
depending on the mode.
In continuous mode each bit corresponds to one of the 16 aux channels. And
the single ADC will convert them one by one in order.
In simultaneous mode the aux channels are split into two groups the first 8
channels are assigned to the first ADC and the other 8 channels to the
second ADC. The upper 8 bits of the sequencing register are unused and the
lower 8 bits control both ADCs. This means a bit needs to be set if either
the corresponding channel from the first group or the second group (or
both) are set.
Currently the driver does not have the special handling required for
simultaneous mode. Add it.
Signed-off-by: Lars-Peter Clausen <[email protected]>
Fixes: bdc8cda1d010 ("iio:adc: Add Xilinx XADC driver")
Cc: <[email protected]>
Signed-off-by: Jonathan Cameron <[email protected]>
|
|
When enabling the trigger and unmasking the end-of-sequence (EOS) interrupt
the EOS interrupt should be cleared from the status register. Otherwise it
is possible that it was still set from a previous capture. If that is the
case the interrupt would fire immediately even though no conversion has
been done yet and stale data is being read from the device.
The old code only clears the interrupt if the interrupt was previously
unmasked. Which does not make much sense since the interrupt is always
masked at this point and in addition masking the interrupt does not clear
the interrupt from the status register. So the clearing needs to be done
unconditionally.
Signed-off-by: Lars-Peter Clausen <[email protected]>
Fixes: bdc8cda1d010 ("iio:adc: Add Xilinx XADC driver")
Cc: <[email protected]>
Signed-off-by: Jonathan Cameron <[email protected]>
|
|
The check for shutting down the second ADC is inverted. This causes it to
be powered down when it should be enabled. As a result channels that are
supposed to be handled by the second ADC return invalid conversion results.
Signed-off-by: Lars-Peter Clausen <[email protected]>
Fixes: bdc8cda1d010 ("iio:adc: Add Xilinx XADC driver")
Cc: <[email protected]>
Signed-off-by: Jonathan Cameron <[email protected]>
|
|
Currently there is an off-by-one check on the number of channels that
will cause an arry overrun in array st->output_mode when calling the
function d5770r_store_output_range. Fix this by using >= rather than >
to check for maximum number of channels.
Addresses-Coverity: ("Out-of-bounds access")
Fixes: cbbb819837f6 ("iio: dac: ad5770r: Add AD5770R support")
Signed-off-by: Colin Ian King <[email protected]>
Reviewed-by: Alexandru Ardelean <[email protected]>
Signed-off-by: Jonathan Cameron <[email protected]>
|
|
flush hw FIFO before device reset in order to avoid possible races
on interrupt line 1. If the first interrupt line is asserted during
hw reset the device will work in I3C-only mode (if it is supported)
Fixes: 801a6e0af0c6 ("iio: imu: st_lsm6dsx: add support to LSM6DSO")
Fixes: 43901008fde0 ("iio: imu: st_lsm6dsx: add support to LSM6DSR")
Reported-by: Mario Tesi <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Reviewed-by: Vitor Soares <[email protected]>
Tested-by: Vitor Soares <[email protected]>
Cc: <[email protected]>
Signed-off-by: Jonathan Cameron <[email protected]>
|
|
This patch fixes the call to iio_str_to_fixpoint when using 'dB' sufix.
Before this the scale_db was not used when parsing the string written to
the attribute and it failed with invalid value.
Fixes: b8528224741b ("iio: core: Handle 'dB' suffix in core")
Signed-off-by: Mircea Caprioru <[email protected]>
Signed-off-by: Jonathan Cameron <[email protected]>
|
|
Fix id relative path that shouldn't contain 'bindings', as pointed out
when submitting st,stm32-dac bindings conversion to json-schema [1].
[1] https://patchwork.ozlabs.org/patch/1257568/
Fixes: a8cf1723c4b7 ("dt-bindings: iio: adc: stm32-adc: convert bindings to json-schema")
Signed-off-by: Fabrice Gasnier <[email protected]>
Signed-off-by: Jonathan Cameron <[email protected]>
|
|
Add lock protection from race conditions to 104-quad-8 counter driver
generic interface code changes. Mutex calls used for protection.
Fixes: f1d8a071d45b ("counter: 104-quad-8: Add Generic Counter interface support")
Signed-off-by: Syed Nayyar Waris <[email protected]>
Signed-off-by: William Breathitt Gray <[email protected]>
Signed-off-by: Jonathan Cameron <[email protected]>
|
|
conf.listen_interval can sometimes be zero causing wake_up_count
to wrap around up to many beacons too late causing
CTRL-EVENT-BEACON-LOSS as in.
wpa_supplicant[795]: message repeated 45 times: [..CTRL-EVENT-BEACON-LOSS ]
Fixes: 43c93d9bf5e2 ("staging: vt6656: implement power saving code.")
Cc: stable <[email protected]>
Signed-off-by: Malcolm Priestley <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The DT2815 analog output command is 16 bits wide, consisting of the
12-bit sample value in bits 15 to 4, the channel number in bits 3 to 1,
and a voltage or current selector in bit 0. Both bytes of the 16-bit
command need to be written in turn to a single 8-bit data register.
However, the driver currently only writes the low 8-bits. It is broken
and appears to have always been broken.
Electronic copies of the DT2815 User's Manual seem impossible to find
online, but looking at the source code, a best guess for the sequence
the driver intended to use to write the analog output command is as
follows:
1. Wait for the status register to read 0x00.
2. Write the low byte of the command to the data register.
3. Wait for the status register to read 0x80.
4. Write the high byte of the command to the data register.
Step 4 is missing from the driver. Add step 4 to (hopefully) fix the
driver.
Also add a "FIXME" comment about setting bit 0 of the low byte of the
command. Supposedly, it is used to choose between voltage output and
current output, but the current driver always sets it to 1.
Signed-off-by: Ian Abbott <[email protected]>
Cc: stable <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Fix incongruency in handling of sysfs entries creation.
This issue could cause invalid memory accesses, by not properly
detecting the end of the sysfs attributes array.
Fixes: 84c45d5f3bf1 ("staging: gasket: Replace macro __ATTR with __ATTR_NULL")
Signed-off-by: Luis Mendes <[email protected]>
Cc: stable <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
|
|
This sorts the actual field names too, potentially causing even more
chaos and confusion at merge time if you have edited the MAINTAINERS
file. But the end result is a more consistent layout, and hopefully
it's a one-time pain minimized by doing this just before the -rc1
release.
This was entirely scripted:
./scripts/parse-maintainers.pl --input=MAINTAINERS --output=MAINTAINERS --order
Requested-by: Joe Perches <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
They are all supposed to be sorted, but people who add new entries don't
always know the alphabet. Plus sometimes the entry names get edited,
and people don't then re-order the entry.
Let's see how painful this will be for merging purposes (the MAINTAINERS
file is often edited in various different trees), but Joe claims there's
relatively few patches in -next that touch this, and doing it just
before -rc1 is likely the best time. Fingers crossed.
This was scripted with
/scripts/parse-maintainers.pl --input=MAINTAINERS --output=MAINTAINERS
but then I also ended up manually upper-casing a few entry names that
stood out when looking at the end result.
Requested-by: Joe Perches <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A set of three patches to fix the fallout of the newly added split
lock detection feature.
It addressed the case where a KVM guest triggers a split lock #AC and
KVM reinjects it into the guest which is not prepared to handle it.
Add proper sanity checks which prevent the unconditional injection
into the guest and handles the #AC on the host side in the same way as
user space detections are handled. Depending on the detection mode it
either warns and disables detection for the task or kills the task if
the mode is set to fatal"
* tag 'x86-urgent-2020-04-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
KVM: VMX: Extend VMXs #AC interceptor to handle split lock #AC in guest
KVM: x86: Emulate split-lock access as a write in emulator
x86/split_lock: Provide handle_guest_split_lock()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull time(keeping) updates from Thomas Gleixner:
- Fix the time_for_children symlink in /proc/$PID/ so it properly
reflects that it part of the 'time' namespace
- Add the missing userns limit for the allowed number of time
namespaces, which was half defined but the actual array member was
not added. This went unnoticed as the array has an exessive empty
member at the end but introduced a user visible regression as the
output was corrupted.
- Prevent further silent ucount corruption by adding a BUILD_BUG_ON()
to catch half updated data.
* tag 'timers-urgent-2020-04-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
ucount: Make sure ucounts in /proc/sys/user don't regress again
time/namespace: Add max_time_namespaces ucount
time/namespace: Fix time_for_children symlink
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes/updates from Thomas Gleixner:
- Deduplicate the average computations in the scheduler core and the
fair class code.
- Fix a raise between runtime distribution and assignement which can
cause exceeding the quota by up to 70%.
- Prevent negative results in the imbalanace calculation
- Remove a stale warning in the workqueue code which can be triggered
since the call site was moved out of preempt disabled code. It's a
false positive.
- Deduplicate the print macros for procfs
- Add the ucmap values to the SCHED_DEBUG procfs output for completness
* tag 'sched-urgent-2020-04-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/debug: Add task uclamp values to SCHED_DEBUG procfs
sched/debug: Factor out printing formats into common macros
sched/debug: Remove redundant macro define
sched/core: Remove unused rq::last_load_update_tick
workqueue: Remove the warning in wq_worker_sleeping()
sched/fair: Fix negative imbalance in imbalance calculation
sched/fair: Fix race between runtime distribution and assignment
sched/fair: Align rq->avg_idle and rq->avg_scan_cost
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Thomas Gleixner:
"Three fixes/updates for perf:
- Fix the perf event cgroup tracking which tries to track the cgroup
even for disabled events.
- Add Ice Lake server support for uncore events
- Disable pagefaults when retrieving the physical address in the
sampling code"
* tag 'perf-urgent-2020-04-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Disable page faults when getting phys address
perf/x86/intel/uncore: Add Ice Lake server uncore support
perf/cgroup: Correct indirection in perf_less_group_idx()
perf/core: Fix event cgroup tracking
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Thomas Gleixner:
"Three small fixes/updates for the locking core code:
- Plug a task struct reference leak in the percpu rswem
implementation.
- Document the refcount interaction with PID_MAX_LIMIT
- Improve the 'invalid wait context' data dump in lockdep so it
contains all information which is required to decode the problem"
* tag 'locking-urgent-2020-04-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/lockdep: Improve 'invalid wait context' splat
locking/refcount: Document interaction with PID_MAX_LIMIT
locking/percpu-rwsem: Fix a task_struct refcount
|
|
Pull cifs fixes from Steve French:
"Ten cifs/smb fixes:
- five RDMA (smbdirect) related fixes
- add experimental support for swap over SMB3 mounts
- also a fix which improves performance of signed connections"
* tag '5.7-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
smb3: enable swap on SMB3 mounts
smb3: change noisy error message to FYI
smb3: smbdirect support can be configured by default
cifs: smbd: Do not schedule work to send immediate packet on every receive
cifs: smbd: Properly process errors on ib_post_send
cifs: Allocate crypto structures on the fly for calculating signatures of incoming packets
cifs: smbd: Update receive credits before sending and deal with credits roll back on failure before sending
cifs: smbd: Check send queue size before posting a send
cifs: smbd: Merge code to track pending packets
cifs: ignore cached share root handle closing errors
|
|
Pull NFS client bugfix from Trond Myklebust:
"Fix an RCU read lock leakage in pnfs_alloc_ds_commits_list()"
* tag 'nfs-for-5.7-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
pNFS: Fix RCU lock leakage
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lftan/nios2
Pull nios2 updates from Ley Foon Tan:
- Remove [email protected] from MAINTAINERS
- remove 'resetvalue' property
- rename 'altr,gpio-bank-width' -> 'altr,ngpio'
- enable the common clk subsystem on Nios2
* tag 'nios2-v5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/lftan/nios2:
MAINTAINERS: Remove [email protected]
arch: nios2: remove 'resetvalue' property
arch: nios2: rename 'altr,gpio-bank-width' -> 'altr,ngpio'
arch: nios2: Enable the common clk subsystem on Nios2
|
|
Pull dma-mapping fixes from Christoph Hellwig:
- fix an integer truncation in dma_direct_get_required_mask
(Kishon Vijay Abraham)
- fix the display of dma mapping types (Grygorii Strashko)
* tag 'dma-mapping-5.7-1' of git://git.infradead.org/users/hch/dma-mapping:
dma-debug: fix displaying of dma allocation type
dma-direct: fix data truncation in dma_direct_get_required_mask()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- raise minimum supported binutils version to 2.23
- remove old CONFIG_AS_* macros that we know binutils >= 2.23 supports
- move remaining CONFIG_AS_* tests to Kconfig from Makefile
- enable -Wtautological-compare warnings to catch more issues
- do not support GCC plugins for GCC <= 4.7
- fix various breakages of 'make xconfig'
- include the linker version used for linking the kernel into
LINUX_COMPILER, which is used for the banner, and also exposed to
/proc/version
- link lib-y objects to vmlinux forcibly when CONFIG_MODULES=y, which
allows us to remove the lib-ksyms.o workaround, and to solve the last
known issue of the LLVM linker
- add dummy tools in scripts/dummy-tools/ to enable all compiler tests
in Kconfig, which will be useful for distro maintainers
- support the single switch, LLVM=1 to use Clang and all LLVM utilities
instead of GCC and Binutils.
- support LLVM_IAS=1 to enable the integrated assembler, which is still
experimental
* tag 'kbuild-v5.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (36 commits)
kbuild: fix comment about missing include guard detection
kbuild: support LLVM=1 to switch the default tools to Clang/LLVM
kbuild: replace AS=clang with LLVM_IAS=1
kbuild: add dummy toolchains to enable all cc-option etc. in Kconfig
kbuild: link lib-y objects to vmlinux forcibly when CONFIG_MODULES=y
MIPS: fw: arc: add __weak to prom_meminit and prom_free_prom_memory
kbuild: remove -I$(srctree)/tools/include from scripts/Makefile
kbuild: do not pass $(KBUILD_CFLAGS) to scripts/mkcompile_h
Documentation/llvm: fix the name of llvm-size
kbuild: mkcompile_h: Include $LD version in /proc/version
kconfig: qconf: Fix a few alignment issues
kconfig: qconf: remove some old bogus TODOs
kconfig: qconf: fix support for the split view mode
kconfig: qconf: fix the content of the main widget
kconfig: qconf: Change title for the item window
kconfig: qconf: clean deprecated warnings
gcc-plugins: drop support for GCC <= 4.7
kbuild: Enable -Wtautological-compare
x86: update AS_* macros to binutils >=2.23, supporting ADX and AVX2
crypto: x86 - clean up poly1305-x86_64-cryptogams.S by 'make clean'
...
|
|
I do not longer work for credativ Germany.
Please, use my private email address instead.
This is for the case when people want to CC me on
patches sent from my old business email address.
Signed-off-by: Sedat Dilek <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Another brown paper bag moment. pnfs_alloc_ds_commits_list() is leaking
the RCU lock.
Fixes: a9901899b649 ("pNFS: Add infrastructure for cleaning up per-layout commit structures")
Signed-off-by: Trond Myklebust <[email protected]>
|
|
Two types of #AC can be generated in Intel CPUs:
1. legacy alignment check #AC
2. split lock #AC
Reflect #AC back into the guest if the guest has legacy alignment checks
enabled or if split lock detection is disabled.
If the #AC is not a legacy one and split lock detection is enabled, then
invoke handle_guest_split_lock() which will either warn and disable split
lock detection for this task or force SIGBUS on it.
[ tglx: Switch it to handle_guest_split_lock() and rename the misnamed
helper function. ]
Suggested-by: Sean Christopherson <[email protected]>
Signed-off-by: Xiaoyao Li <[email protected]>
Signed-off-by: Sean Christopherson <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Signed-off-by: Borislav Petkov <[email protected]>
Acked-by: Paolo Bonzini <[email protected]>
Link: https://lkml.kernel.org/r/[email protected]
|
|
Emulate split-lock accesses as writes if split lock detection is on
to avoid #AC during emulation, which will result in a panic(). This
should never occur for a well-behaved guest, but a malicious guest can
manipulate the TLB to trigger emulation of a locked instruction[1].
More discussion can be found at [2][3].
[1] https://lkml.kernel.org/r/[email protected]
[2] https://lkml.kernel.org/r/[email protected]
[3] https://lkml.kernel.org/r/[email protected]
Suggested-by: Sean Christopherson <[email protected]>
Signed-off-by: Xiaoyao Li <[email protected]>
Signed-off-by: Sean Christopherson <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Signed-off-by: Borislav Petkov <[email protected]>
Acked-by: Paolo Bonzini <[email protected]>
Link: https://lkml.kernel.org/r/[email protected]
|
|
Without at least minimal handling for split lock detection induced #AC,
VMX will just run into the same problem as the VMWare hypervisor, which
was reported by Kenneth.
It will inject the #AC blindly into the guest whether the guest is
prepared or not.
Provide a function for guest mode which acts depending on the host
SLD mode. If mode == sld_warn, treat it like user space, i.e. emit a
warning, disable SLD and mark the task accordingly. Otherwise force
SIGBUS.
[ bp: Add a !CPU_SUP_INTEL stub for handle_guest_split_lock(). ]
Signed-off-by: Thomas Gleixner <[email protected]>
Signed-off-by: Borislav Petkov <[email protected]>
Acked-by: Paolo Bonzini <[email protected]>
Link: https://lkml.kernel.org/r/[email protected]
Link: https://lkml.kernel.org/r/[email protected]
|
|
The keyword here is 'twice' to explain the trick.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Merge yet more updates from Andrew Morton:
- Almost all of the rest of MM (memcg, slab-generic, slab, pagealloc,
gup, hugetlb, pagemap, memremap)
- Various other things (hfs, ocfs2, kmod, misc, seqfile)
* akpm: (34 commits)
ipc/util.c: sysvipc_find_ipc() should increase position index
kernel/gcov/fs.c: gcov_seq_next() should increase position index
fs/seq_file.c: seq_read(): add info message about buggy .next functions
drivers/dma/tegra20-apb-dma.c: fix platform_get_irq.cocci warnings
change email address for Pali Rohár
selftests: kmod: test disabling module autoloading
selftests: kmod: fix handling test numbers above 9
docs: admin-guide: document the kernel.modprobe sysctl
fs/filesystems.c: downgrade user-reachable WARN_ONCE() to pr_warn_once()
kmod: make request_module() return an error when autoloading is disabled
mm/memremap: set caching mode for PCI P2PDMA memory to WC
mm/memory_hotplug: add pgprot_t to mhp_params
powerpc/mm: thread pgprot_t through create_section_mapping()
x86/mm: introduce __set_memory_prot()
x86/mm: thread pgprot_t through init_memory_mapping()
mm/memory_hotplug: rename mhp_restrictions to mhp_params
mm/memory_hotplug: drop the flags field from struct mhp_restrictions
mm/special: create generic fallbacks for pte_special() and pte_mkspecial()
mm/vma: introduce VM_ACCESS_FLAGS
mm/vma: define a default value for VM_DATA_DEFAULT_FLAGS
...
|
|
Pull Documentation fixes from Jonathan Corbet:
"A handful of late-arriving fixes for the documentation tree"
* tag 'docs-5.7-2' of git://git.lwn.net/linux:
Documentation: android: binderfs: add 'stats' mount option
Documentation: driver-api/usb/writing_usb_driver.rst Updates documentation links
docs: driver-api: address duplicate label warning
Documentation: sysrq: fix RST formatting
docs: kernel-parameters.txt: Fix broken references
docs: kernel-parameters.txt: Remove nompx
docs: filesystems: fix typo in qnx6.rst
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux
Pull orangefs updates from Mike Marshall:
"A fix and two cleanups.
Fix:
- Christoph Hellwig noticed that some logic I added to
orangefs_file_read_iter introduced a race condition, so he sent a
reversion patch. I had to modify his patch since reverting at this
point broke Orangefs.
Cleanups:
- Christoph Hellwig noticed that we were doing some unnecessary work
in orangefs_flush, so he sent in a patch that removed the un-needed
code.
- Al Viro told me he had trouble building Orangefs. Orangefs should
be easy to build, even for Al :-).
I looked back at the test server build notes in orangefs.txt, just
in case that's where the trouble really is, and found a couple of
typos and made a couple of clarifications"
* tag 'for-linus-5.7-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux:
orangefs: clarify build steps for test server in orangefs.txt
orangefs: don't mess with I_DIRTY_TIMES in orangefs_flush
orangefs: get rid of knob code...
|
|
Pull xtensa updates from Max Filippov:
- replace setup_irq() by request_irq()
- cosmetic fixes in xtensa Kconfig and boot/Makefile
* tag 'xtensa-20200410' of git://github.com/jcmvbkbc/linux-xtensa:
arch/xtensa: fix grammar in Kconfig help text
xtensa: remove meaningless export ccflags-y
xtensa: replace setup_irq() by request_irq()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull more xen updates from Juergen Gross:
- two cleanups
- fix a boot regression introduced in this merge window
- fix wrong use of memory allocation flags
* tag 'for-linus-5.7-rc1b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
x86/xen: fix booting 32-bit pv guest
x86/xen: make xen_pvmmu_arch_setup() static
xen/blkfront: fix memory allocation flags in blkfront_setup_indirect()
xen: Use evtchn_type_t as a type for event channels
|
|
If seq_file .next function does not change position index, read after
some lseek can generate unexpected output.
https://bugzilla.kernel.org/show_bug.cgi?id=206283
Signed-off-by: Vasily Averin <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Acked-by: Waiman Long <[email protected]>
Cc: Davidlohr Bueso <[email protected]>
Cc: Manfred Spraul <[email protected]>
Cc: Al Viro <[email protected]>
Cc: Ingo Molnar <[email protected]>
Cc: NeilBrown <[email protected]>
Cc: Peter Oberparleiter <[email protected]>
Cc: Steven Rostedt <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Linus Torvalds <[email protected]>
|
|
If seq_file .next function does not change position index, read after
some lseek can generate unexpected output.
https://bugzilla.kernel.org/show_bug.cgi?id=206283
Signed-off-by: Vasily Averin <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Acked-by: Peter Oberparleiter <[email protected]>
Cc: Al Viro <[email protected]>
Cc: Davidlohr Bueso <[email protected]>
Cc: Ingo Molnar <[email protected]>
Cc: Manfred Spraul <[email protected]>
Cc: NeilBrown <[email protected]>
Cc: Steven Rostedt <[email protected]>
Cc: Waiman Long <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Linus Torvalds <[email protected]>
|