| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Try to print out startup pgm check info including exact linux kernel
version, pgm interruption code and ilc, psw and general registers. Like
the following:
Linux version 5.3.0-rc7-07282-ge7b4d41d61bd-dirty (gor@tuxmaker) #3 SMP PREEMPT Thu Sep 5 16:07:34 CEST 2019
Kernel fault: interruption code 0005 ilc:2
PSW : 0000000180000000 0000000000012e52
R:0 T:0 IO:0 EX:0 Key:0 M:0 W:0 P:0 AS:0 CC:0 PM:0 RI:0 EA:3
GPRS: 0000000000000000 00ffffffffffffff 0000000000000000 0000000000019a58
000000000000bf68 0000000000000000 0000000000000000 0000000000000000
0000000000000000 0000000000000000 000000000001a041 0000000000000000
0000000004c9c000 0000000000010070 0000000000012e42 000000000000beb0
This info makes it apparent that kernel startup failed and might help
to understand what went wrong without actual standalone dump.
Printing code runs on its own stack of 1 page (at unused 0x5000), which
should be sufficient for sclp_early_printk usage (typical stack usage
observed has been around 512 bytes).
The code has pgm check recursion prevention, despite pgm check info
printing failure (follow on pgm check) or success it restores original
faulty psw and gprs and does disabled wait.
Reviewed-by: Heiko Carstens <[email protected]>
Signed-off-by: Vasily Gorbik <[email protected]>
Signed-off-by: Heiko Carstens <[email protected]>
|
|
Add spi large PA(max=64G) support for DMA transfer.
Signed-off-by: luhua.xu <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
This patch add spi support for mt6765 IC.
Signed-off-by: luhua.xu <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Add a DT binding documentation for the MT6765 soc.
Signed-off-by: luhua.xu <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Several header-files, Kconfig files and Makefiles have trailing
white-space. Remove it.
In netfilter/Kconfig, indent the type of CONFIG_NETFILTER_NETLINK_ACCT
correctly.
There are semicolons at the end of two function definitions in
include/net/netfilter/nf_conntrack_acct.h and
include/net/netfilter/nf_conntrack_ecache.h. Remove them.
Fix indentation in nf_conntrack_l4proto.h.
Signed-off-by: Jeremy Sowden <[email protected]>
Signed-off-by: Pablo Neira Ayuso <[email protected]>
|
|
nf_conntrack_labels.h has no include guard. Add it.
The comment following the #endif in the nf_flow_table.h include guard
referred to the wrong macro. Fix it.
Signed-off-by: Jeremy Sowden <[email protected]>
Signed-off-by: Pablo Neira Ayuso <[email protected]>
|
|
This is to allow machine drivers to set a certain bitclk rate
which might not be exactly rate * frame size.
Cc: NXP Linux Team <[email protected]>
Signed-off-by: Viorel Suman <[email protected]>
Signed-off-by: Daniel Baluta <[email protected]>
Acked-by: Nicolin Chen <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
If the net_device unregisters, clean up the offload rules before the
chain is destroy.
Signed-off-by: wenxu <[email protected]>
Signed-off-by: Pablo Neira Ayuso <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fix from Tejun Heo:
"Roman found and fixed a bug in the cgroup2 freezer which allows new
child cgroup to escape frozen state"
* 'for-5.3-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: freezer: fix frozen state inheritance
kselftests: cgroup: add freezer mkdir test
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"Here are two fixes, one of them urgent fixing a bug introduced in 5.2
and reported by many users. It took time to identify the root cause,
catching the 5.3 release is higly desired also to push the fix to 5.2
stable tree.
The bug is a mess up of return values after adding proper error
handling and honestly the kind of bug that can cause sleeping
disorders until it's caught. My appologies to everybody who was
affected.
Summary of what could happen:
1) either a hang when committing a transaction, if this happens
there's no risk of corruption, still the hang is very inconvenient
and can't be resolved without a reboot
2) writeback for some btree nodes may never be started and we end up
committing a transaction without noticing that, this is really
serious and that will lead to the "parent transid verify failed"
messages"
* tag 'for-5.3-rc8-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
Btrfs: fix unwritten extent buffers and hangs on future writeback attempts
Btrfs: fix assertion failure during fsync and use of stale transaction
|
|
Pass rule, chain and flow_rule object parameters to nft_flow_offload_rule
to reuse it.
Signed-off-by: wenxu <[email protected]>
Signed-off-by: Pablo Neira Ayuso <[email protected]>
|
|
Pass chain and policy parameters to nft_flow_offload_chain to reuse it.
Signed-off-by: wenxu <[email protected]>
Signed-off-by: Pablo Neira Ayuso <[email protected]>
|
|
When passing a equal or more then 32 bytes long string to psi_write(),
psi_write() copies 31 bytes to its buf and overwrites buf[30]
with '\0'. Which makes the input string 1 byte shorter than
it should be.
Fix it by copying sizeof(buf) bytes when nbytes >= sizeof(buf).
This does not cause problems in normal use case like:
"some 500000 10000000" or "full 500000 10000000" because they
are less than 32 bytes in length.
/* assuming nbytes == 35 */
char buf[32];
buf_size = min(nbytes, (sizeof(buf) - 1)); /* buf_size = 31 */
if (copy_from_user(buf, user_buf, buf_size))
return -EFAULT;
buf[buf_size - 1] = '\0'; /* buf[30] = '\0' */
Before:
%cd /proc/pressure/
%echo "123456789|123456789|123456789|1234" > memory
[ 22.473497] nbytes=35,buf_size=31
[ 22.473775] 123456789|123456789|123456789| (print 30 chars)
%sh: write error: Invalid argument
%echo "123456789|123456789|123456789|1" > memory
[ 64.916162] nbytes=32,buf_size=31
[ 64.916331] 123456789|123456789|123456789| (print 30 chars)
%sh: write error: Invalid argument
After:
%cd /proc/pressure/
%echo "123456789|123456789|123456789|1234" > memory
[ 254.837863] nbytes=35,buf_size=32
[ 254.838541] 123456789|123456789|123456789|1 (print 31 chars)
%sh: write error: Invalid argument
%echo "123456789|123456789|123456789|1" > memory
[ 9965.714935] nbytes=32,buf_size=32
[ 9965.715096] 123456789|123456789|123456789|1 (print 31 chars)
%sh: write error: Invalid argument
Also remove the superfluous parentheses.
Signed-off-by: Miles Chen <[email protected]>
Cc: <[email protected]>
Cc: <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Link: https://lkml.kernel.org/r/[email protected]
Signed-off-by: Ingo Molnar <[email protected]>
|
|
EAS computes the energy impact of migrating a waking task when deciding
on which CPU it should run. However, the current approach is known to
have a high algorithmic complexity, which can result in prohibitively
high wake-up latencies on systems with complex energy models, such as
systems with per-CPU DVFS. On such systems, the algorithm complexity is
in O(n^2) (ignoring the cost of searching for performance states in the
EM) with 'n' the number of CPUs.
To address this, re-factor the EAS wake-up path to compute the energy
'delta' (with and without the task) on a per-performance domain basis,
rather than system-wide, which brings the complexity down to O(n).
No functional changes intended.
Test results
~~~~~~~~~~~~
* Setup: Tested on a Google Pixel 3, with a Snapdragon 845 (4+4 CPUs,
A55/A75). Base kernel is 5.3-rc5 + Pixel3 specific patches. Android
userspace, no graphics.
* Test case: Run a periodic rt-app task, with 16ms period, ramping down
from 70% to 10%, in 5% steps of 500 ms each (json avail. at [1]).
Frequencies of all CPUs are pinned to max (using scaling_min_freq
CPUFreq sysfs entries) to reduce variability. The time to run
select_task_rq_fair() is measured using the function profiler
(/sys/kernel/debug/tracing/trace_stat/function*). See the test script
for more details [2].
Test 1:
I hacked the DT to 'fake' per-CPU DVFS. That is, we end up with one
CPUFreq policy per CPU (8 policies in total). Since all frequencies are
pinned to max for the test, this should have no impact on the actual
frequency selection, but it does in the EAS calculation.
+---------------------------+----------------------------------+
| Without patch | With patch |
+-----+-----+----------+----------+-----+-----------------+----------+
| CPU | Hit | Avg (us) | s^2 (us) | Hit | Avg (us) | s^2 (us) |
|-----+-----+----------+----------+-----+-----------------+----------+
| 0 | 274 | 38.303 | 1750.239 | 401 | 14.126 (-63.1%) | 146.625 |
| 1 | 197 | 49.529 | 1695.852 | 314 | 16.135 (-67.4%) | 167.525 |
| 2 | 142 | 34.296 | 1758.665 | 302 | 14.133 (-58.8%) | 130.071 |
| 3 | 172 | 31.734 | 1490.975 | 641 | 14.637 (-53.9%) | 139.189 |
| 4 | 316 | 7.834 | 178.217 | 425 | 5.413 (-30.9%) | 20.803 |
| 5 | 447 | 8.424 | 144.638 | 556 | 5.929 (-29.6%) | 27.301 |
| 6 | 581 | 14.886 | 346.793 | 456 | 5.711 (-61.6%) | 23.124 |
| 7 | 456 | 10.005 | 211.187 | 997 | 4.708 (-52.9%) | 21.144 |
+-----+-----+----------+----------+-----+-----------------+----------+
* Hit, Avg and s^2 are as reported by the function profiler
Test 2:
I also ran the same test with a normal DT, with 2 CPUFreq policies, to
see if this causes regressions in the most common case.
+---------------------------+----------------------------------+
| Without patch | With patch |
+-----+-----+----------+----------+-----+-----------------+----------+
| CPU | Hit | Avg (us) | s^2 (us) | Hit | Avg (us) | s^2 (us) |
|-----+-----+----------+----------+-----+-----------------+----------+
| 0 | 345 | 22.184 | 215.321 | 580 | 18.635 (-16.0%) | 146.892 |
| 1 | 358 | 18.597 | 200.596 | 438 | 12.934 (-30.5%) | 104.604 |
| 2 | 359 | 25.566 | 200.217 | 397 | 10.826 (-57.7%) | 74.021 |
| 3 | 362 | 16.881 | 200.291 | 718 | 11.455 (-32.1%) | 102.280 |
| 4 | 457 | 3.822 | 9.895 | 757 | 4.616 (+20.8%) | 13.369 |
| 5 | 344 | 4.301 | 7.121 | 594 | 5.320 (+23.7%) | 18.798 |
| 6 | 472 | 4.326 | 7.849 | 464 | 5.648 (+30.6%) | 22.022 |
| 7 | 331 | 4.630 | 13.937 | 408 | 5.299 (+14.4%) | 18.273 |
+-----+-----+----------+----------+-----+-----------------+----------+
* Hit, Avg and s^2 are as reported by the function profiler
In addition to these two tests, I also ran 50 iterations of the Lisa
EAS functional test suite [3] with this patch applied on Arm Juno r0,
Arm Juno r2, Arm TC2 and Hikey960, and could not see any regressions
(all EAS functional tests are passing).
[1] https://paste.debian.net/1100055/
[2] https://paste.debian.net/1100057/
[3] https://github.com/ARM-software/lisa/blob/master/lisa/tests/scheduler/eas_behaviour.py
Signed-off-by: Quentin Perret <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Link: https://lkml.kernel.org/r/[email protected]
Signed-off-by: Ingo Molnar <[email protected]>
|
|
Make fs_parse() handle fs_param_is_fd-type parameters that are passed a
string by converting it to an integer (in addition to handling direct fd
specification).
Also range check the integer.
[fix from Yin Fengwei folded]
Signed-off-by: David Howells <[email protected]>
Signed-off-by: Al Viro <[email protected]>
|
|
Convert the ramfs, shmem, tmpfs, devtmpfs and rootfs filesystems to the new
internal mount API as the old one will be obsoleted and removed. This
allows greater flexibility in communication of mount parameters between
userspace, the VFS and the filesystem.
See Documentation/filesystems/mount_api.txt for more information.
Note that tmpfs is slightly tricky as it can contain embedded commas, so it
can't be trivially split up using strsep() to break on commas in
generic_parse_monolithic(). Instead, tmpfs has to supply its own generic
parser.
However, if tmpfs changes, then devtmpfs and rootfs, which are wrappers
around tmpfs or ramfs, must change too - and thus so must ramfs, so these
had to be converted also.
[AV: rewritten]
Signed-off-by: David Howells <[email protected]>
cc: Hugh Dickins <[email protected]>
cc: [email protected]
Signed-off-by: Al Viro <[email protected]>
|
|
This thing will eventually become our ->parse_param(), while
shmem_parse_options() - ->parse_monolithic(). At that point
shmem_parse_options() will start calling vfs_parse_fs_string(),
rather than calling shmem_parse_one() directly.
Signed-off-by: Al Viro <[email protected]>
|
|
mechanical move.
Signed-off-by: Al Viro <[email protected]>
|
|
just use ctx->mpol (note that callers always set ctx->mpol to NULL when
calling that).
Signed-off-by: Al Viro <[email protected]>
|
|
... and copy the data from it into sbinfo in the callers.
For use by remount we need to keep track whether there'd
been options setting max_inodes, max_blocks and huge resp.
and do the sanity checks (and copying) only if such options
had been seen. uid/gid/mode is ignored by remount and
NULL mpol is already explicitly treated as "ignore it",
so we don't need to keep track of those.
Note: theoretically, mpol_parse_string() may return NULL
not in case of error (for default policy), so the assumption
that NULL mpol means "change nothing" is incorrect. However,
that's the mainline behaviour and any changes belong in
a separate patch. If we go for that, we'll need to keep
track of having encountered mpol= option too.
[changes in remount logics from Hugh Dickins folded]
Signed-off-by: Al Viro <[email protected]>
|
|
Add __nft_offload_get_chain function to get basechain from device. This
function requires that caller holds the per-netns nftables mutex. This
patch implicitly fixes missing offload flags check and proper mutex from
nft_indr_block_cb().
Fixes: 9a32669fecfb ("netfilter: nf_tables_offload: support indr block call")
Signed-off-by: wenxu <[email protected]>
Signed-off-by: Pablo Neira Ayuso <[email protected]>
|
|
If a new child cgroup is created in the frozen cgroup hierarchy
(one or more of ancestor cgroups is frozen), the CGRP_FREEZE cgroup
flag should be set. Otherwise if a process will be attached to the
child cgroup, it won't become frozen.
The problem can be reproduced with the test_cgfreezer_mkdir test.
This is the output before this patch:
~/test_freezer
ok 1 test_cgfreezer_simple
ok 2 test_cgfreezer_tree
ok 3 test_cgfreezer_forkbomb
Cgroup /sys/fs/cgroup/cg_test_mkdir_A/cg_test_mkdir_B isn't frozen
not ok 4 test_cgfreezer_mkdir
ok 5 test_cgfreezer_rmdir
ok 6 test_cgfreezer_migrate
ok 7 test_cgfreezer_ptrace
ok 8 test_cgfreezer_stopped
ok 9 test_cgfreezer_ptraced
ok 10 test_cgfreezer_vfork
And with this patch:
~/test_freezer
ok 1 test_cgfreezer_simple
ok 2 test_cgfreezer_tree
ok 3 test_cgfreezer_forkbomb
ok 4 test_cgfreezer_mkdir
ok 5 test_cgfreezer_rmdir
ok 6 test_cgfreezer_migrate
ok 7 test_cgfreezer_ptrace
ok 8 test_cgfreezer_stopped
ok 9 test_cgfreezer_ptraced
ok 10 test_cgfreezer_vfork
Reported-by: Mark Crossen <[email protected]>
Signed-off-by: Roman Gushchin <[email protected]>
Fixes: 76f969e8948d ("cgroup: cgroup v2 freezer")
Cc: Tejun Heo <[email protected]>
Cc: [email protected] # v5.2+
Signed-off-by: Tejun Heo <[email protected]>
|
|
Add a new cgroup freezer selftest, which checks that if a cgroup is
frozen, their new child cgroups will properly inherit the frozen
state.
It creates a parent cgroup, freezes it, creates a child cgroup
and populates it with a dummy process. Then it checks that both
parent and child cgroup are frozen.
Signed-off-by: Roman Gushchin <[email protected]>
Cc: Tejun Heo <[email protected]>
Cc: Shuah Khan <[email protected]>
Signed-off-by: Tejun Heo <[email protected]>
|
|
The way the logic is setup in io_uring_enter() means that you can't wake
up the SQ poller thread while at the same time waiting (or polling) for
completions afterwards. There's no reason for that to be the case.
Reported-by: Lewis Baker <[email protected]>
Reviewed-by: Jeff Moyer <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
We currently merge async work items if we see a strict sequential hit.
This helps avoid unnecessary workqueue switches when we don't need
them. We can extend this merging to cover cases where it's not a strict
sequential hit, but the IO still fits within the same page. If an
application is doing multiple requests within the same page, we don't
want separate workers waiting on the same page to complete IO. It's much
faster to let the first worker bring in the page, then operate on that
page from the same worker to complete the next request(s).
Reviewed-by: Jeff Moyer <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
temperature and fan.
According to datasheet, the SMI status register setting of LTD
temperature is SMI_STS3, and the SMI status register setting
of fan is SMI_STS5 and SMI_STS6.
Signed-off-by: amy.shih <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Guenter Roeck <[email protected]>
|
|
Fix the error handling for the led-max-microamp property.
Need to check if the property is present and then if it is
retrieve the setting and its max boundary
Reported-by: Pavel Machek <[email protected]>
Signed-off-by: Dan Murphy <[email protected]>
Signed-off-by: Jacek Anaszewski <[email protected]>
|
|
Bump version to 0.8.1-k
Signed-off-by: Tony Nguyen <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
Attempt to request an optional device-specific DDP package file
(one with the PCIe Device Serial Number in its name so that different DDP
package files can be used on different devices). If the optional package
file exists, download it to the device. If not, download the default
package file.
Log an appropriate message based on whether or not a DDP package
file exists and the return code from the attempt to download it to the
device. If the download fails and there is not already a package file on
the device, go into "Safe Mode" where some features are not supported.
Signed-off-by: Tony Nguyen <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
Add functions to initialize, parse, and clean structures representing
the DDP package.
Upon completion of package download, read and store the DDP package
contents to these structures. This configuration is used to
identify the default behavior and later used to update the HW table
entries.
Signed-off-by: Tony Nguyen <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
Add the required defines, structures, and functions to enable downloading
a DDP package. Before download, checks are performed to ensure the package
is valid and compatible.
Note that package download is not yet requested by the driver as further
initialization is required to utilize the package.
Signed-off-by: Tony Nguyen <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
The FW build id is currently being displayed as an int which doesn't make
sense. Instead display FW build id as a hex value. Also add other useful
information to the output such as NVM version, API patch info, and FW
build hash.
Signed-off-by: Lukasz Czapnik <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
The driver is required to send a version to the firmware
to indicate that the driver is up. If the driver doesn't
do this the firmware doesn't behave properly.
Signed-off-by: Paul M Stillwell Jr <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
Pull NVMe updates from Sagi:
"Highlights includes:
- controller reset and namespace scan races fixes
- nvme discovery log change uevent support
- naming improvements from Keith
- multiple discovery controllers reject fix from James
- some regular cleanups from various people"
* 'nvme-5.4' of git://git.infradead.org/nvme:
nvmet: fix a wrong error status returned in error log page
nvme: send discovery log page change events to userspace
nvme: add uevent variables for controller devices
nvme: enable aen regardless of the presence of I/O queues
nvme-fabrics: allow discovery subsystems accept a kato
nvmet: Use PTR_ERR_OR_ZERO() in nvmet_init_discovery()
nvme: Remove redundant assignment of cq vector
nvme: Assign subsys instance from first ctrl
nvme: tcp: remove redundant assignment to variable ret
nvme: include admin_q sync with nvme_sync_queues
nvme: Treat discovery subsystems as unique subsystems
nvme: fix ns removal hang when failing to revalidate due to a transient error
nvme: make nvme_report_ns_ids propagate error back
nvme: make nvme_identify_ns propagate errors back
nvme: pass status to nvme_error_status
nvme-fc: Fail transport errors with NVME_SC_HOST_PATH
nvme-tcp: fail command with NVME_SC_HOST_PATH_ERROR send failed
nvme: fail cancelled commands with NVME_SC_HOST_PATH_ERROR
|
|
When the command data_len cannot hold all the controller errors,
we should simply return as much errors as we can fit
instead of failing the command.
Signed-off-by: Amit Engel <[email protected]>
Reviewed-by: Christoph Hellwig <[email protected]>
Signed-off-by: Sagi Grimberg <[email protected]>
|
|
If the controller supports discovery log page change events,
we want to enable it. When we see a discovery log change event
we will send it up to userspace and expect it to handle it.
Reviewed-by: Minwoo Im <[email protected]>
Reviewed-by: James Smart <[email protected]>
Reviewed-by: Hannes Reinecke <[email protected]>
Reviewed-by: Christoph Hellwig <[email protected]>
Reviewed-by: Chaitanya Kulkarni <[email protected]>
Signed-off-by: Sagi Grimberg <[email protected]>
|
|
When we send uevents to userspace, add controller specific
environment variables to uniquly identify the controller beyond
its device name.
This will be useful to address discovery log change events by
actually verifying that the discovery controller is indeed the
same as the device that generated the event.
Reviewed-by: Hannes Reinecke <[email protected]>
Signed-off-by: Sagi Grimberg <[email protected]>
|
|
AENs in general are not related to the presence of I/O queues,
so enable them regardless. Note that the only exception is that
discovery controller will not support any of the requested AENs
and nvme_enable_aen will respect that and return, so it is still
safe to enable regardless.
Note it is safe to enable AENs even before the initial namespace
scanning as we have the scan operation in a workqueue context.
Reviewed-by: Minwoo Im <[email protected]>
Reviewed-by: Christoph Hellwig <[email protected]>
Reviewed-by: Chaitanya Kulkarni <[email protected]>
Reviewed-by: Hannes Reinecke <[email protected]>
Signed-off-by: Sagi Grimberg <[email protected]>
|
|
This modifies the behavior of discovery subsystems to accept
a kato as a preparation to support discovery log change
events. This also means that now every discovery controller
will have a default kato value, and for non-persistent connections
the host needs to pass in a zero kato value (keep_alive_tmo=0).
Reviewed-by: Minwoo Im <[email protected]>
Reviewed-by: James Smart <[email protected]>
Reviewed-by: Hannes Reinecke <[email protected]>
Reviewed-by: Christoph Hellwig <[email protected]>
Reviewed-by: Chaitanya Kulkarni <[email protected]>
Signed-off-by: Sagi Grimberg <[email protected]>
|
|
Simplify this function implementation by using a known function.
Generated by: scripts/coccinelle/api/ptr_ret.cocci
Signed-off-by: Markus Elfring <[email protected]>
Reviewed-by: Sagi Grimberg <[email protected]>
Signed-off-by: Sagi Grimberg <[email protected]>
|
|
The cq vector is already assigned with the correct value.
Signed-off-by: Israel Rukshin <[email protected]>
Reviewed-by: Max Gurtovoy <[email protected]>
Reviewed-by: Keith Busch <[email protected]>
Reviewed-off-by: Sagi Grimberg <[email protected]>
Signed-off-by: Sagi Grimberg <[email protected]>
|
|
The namespace disk names must be unique for the lifetime of the
subsystem. This was accomplished by using their parent subsystems'
instances which were allocated independently from the controllers
connected to that subsystem. This allowed name prefixes assigned to
namespaces to match a controller from an unrelated subsystem, and has
created confusion among users examining device nodes.
Ensure a namespace's subsystem instance never clashes with a controller
instance of another subsystem by transferring the instance ownership
to the parent subsystem from the first controller discovered in that
subsystem.
Reviewed-by: Logan Gunthorpe <[email protected]>
Signed-off-by: Keith Busch <[email protected]>
Reviewed-by: Christoph Hellwig <[email protected]>
Reviewed-by: Minwoo Im <[email protected]>
Reviewed-by: Hannes Reinecke <[email protected]>
Reviewed-off-by: Sagi Grimberg <[email protected]>
Signed-off-by: Sagi Grimberg <[email protected]>
|
|
The variable ret is being initialized with a value that is never read
and is being re-assigned immediately afterwards. The assignment is
redundant and hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <[email protected]>
Reviewed-by: Max Gurtovoy <[email protected]>
Signed-off-by: Sagi Grimberg <[email protected]>
|
|
nvme_sync_queues currently syncs all namespace queues, but should
also sync the admin queue, if present.
Signed-off-by: Edmund Nadolski <[email protected]>
Reviewed-by: Keith Busch <[email protected]>
Reviewed-by: Christoph Hellwig <[email protected]>
Signed-off-by: Sagi Grimberg <[email protected]>
|
|
Current code matches subnqn and collapses all controllers to the
same subnqn to a single subsystem structure. This is good for
recognizing multiple controllers for the same subsystem. But with
the well-known discovery subnqn, the subsystems aren't truly the
same subsystem. As such, subsystem specific rules, such as no
overlap of controller id, do not apply. With today's behavior, the
check for overlap of controller id can fail, preventing the new
discovery controller from being created.
When searching for like subsystem nqn, exclude the discovery nqn
from matching. This will result in each discovery controller being
attached to a unique subsystem structure.
Signed-off-by: James Smart <[email protected]>
Reviewed-by: Sagi Grimberg <[email protected]>
Reviewed-by: Christoph Hellwig <[email protected]>
Reviewed-by: Max Gurtovoy <[email protected]>
Signed-off-by: Sagi Grimberg <[email protected]>
|
|
If a controller reset is racing with a namespace revalidation, the
revalidation (admin) I/O will surely fail, but we should not remove the
namespace as we will execute the I/O when the controller is back up.
Same for spurious allocation errors (return -ENOMEM).
Fix this by checking the specific error code in nvme_revalidate_disk and
if it is a transient error (for example non DNR nvme statuses or
a negative ENOMEM as allocation failure), do not remove the namespace as
it will either recover when the controller is back up and schedule
a subsequent scan, or the controller is going away and the namespaces
will be removed anyways.
This fixes a hang namespace scanning racing with a controller reset and
also sporious I/O errors in path failover coditions where the
controller reset is racing with the namespace scan work with multipath
enabled.
Reported-by: Hannes Reinecke <[email protected]>
Reviewed-by: Hannes Reinecke <[email protected]>
Reviewed-by: James Smart <[email protected]>
Reviewed-by: Christoph Hellwig <[email protected]>
Signed-off-by: Sagi Grimberg <[email protected]>
|
|
Make the callers check the return status and propagate
back accordingly (casting to errno from a positive nvme status).
Also print the return status in nvme_report_ns_ids.
Reviewed-by: Hannes Reinecke <[email protected]>
Reviewed-by: James Smart <[email protected]>
Reviewed-by: Christoph Hellwig <[email protected]>
Reviewed-by: Chaitanya Kulkarni <[email protected]>
Signed-off-by: Sagi Grimberg <[email protected]>
|
|
right now callers of nvme_identify_ns only know that it failed,
but don't know why. Make nvme_identify_ns propagate the error back.
Because nvme_submit_sync_cmd may return a positive status code, we
make nvme_identify_ns receive the id by reference and return that
status up the call chain, but make sure not to leak positive nvme
status codes to the upper layers.
Reviewed-by: Minwoo Im <[email protected]>
Reviewed-by: Hannes Reinecke <[email protected]>
Reviewed-by: James Smart <[email protected]>
Reviewed-by: Chaitanya Kulkarni <[email protected]>
Reviewed-by: Christoph Hellwig <[email protected]>
Signed-off-by: Sagi Grimberg <[email protected]>
|
|
No need for the full blown request structure.
Reviewed-by: Christoph Hellwig <[email protected]>
Signed-off-by: Sagi Grimberg <[email protected]>
|
|
NVME_SC_INTERNAL should indicate an internal controller errors
and not host transport errors. These errors will propagate to
upper layers (essentially nvme core) and be interpereted as
transport errors which should not be taken into account for
namespace state or condition.
Reviewed-by: Hannes Reinecke <[email protected]>
Reviewed-by: James Smart <[email protected]>
Reviewed-by: Christoph Hellwig <[email protected]>
Signed-off-by: Sagi Grimberg <[email protected]>
|