| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The function dev_queue_xmit_skb_sk is unncessary and very confusing.
Introduce arp_xmit_finish to remove the need for dev_queue_xmit_skb_sk,
and have arp_xmit_finish call dev_queue_xmit.
Signed-off-by: "Eric W. Biederman" <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Signed-off-by: "Eric W. Biederman" <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Signed-off-by: "Eric W. Biederman" <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Signed-off-by: "Eric W. Biederman" <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Signed-off-by: "Eric W. Biederman" <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Signed-off-by: "Eric W. Biederman" <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Signed-off-by: "Eric W. Biederman" <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Calling dev_net(dev) for is just silly.
Signed-off-by: "Eric W. Biederman" <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This is a prepatory patch to passing net int the netfilter hooks,
where net will be used again.
Signed-off-by: "Eric W. Biederman" <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Signed-off-by: "Eric W. Biederman" <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Signed-off-by: "Eric W. Biederman" <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Compute struct net from the input device in ip_forward before it is
used.
Signed-off-by: "Eric W. Biederman" <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Add a sock paramter to dst_output making dst_output_sk superfluous.
Add a skb->sk parameter to all of the callers of dst_output
Have the callers of dst_output_sk call dst_output.
Signed-off-by: "Eric W. Biederman" <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Signed-off-by: "Eric W. Biederman" <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Signed-off-by: "Eric W. Biederman" <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Signed-off-by: "Eric W. Biederman" <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The !CONFIG_NETFILTER definition of nf_hook_thresh calls okfn when
the CONFIG_NETFITLER defintion does not, making it buggy.
As the !CONFIG_NETFILTER defintion of nf_hook_thresh is not used remove
it rather than fix it.
Signed-off-by: "Eric W. Biederman" <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-09-15
This series contains updates to ixgbe and fm10k.
Don fixes a ixgbe issue by adding checks for systems that do not have
SFP's to avoid incorrectly acting on interrupts that are falsely
interpreted as SFP events.
Alex Williamson adds a fix for ixgbe to disable SR-IOV prior to
unregistering the netdev to avoid issues with guest OS's which do not
support hot-unplug or their hot-unplug is broken.
Alex Duyck update the lowest limit for adaptive interrupt interrupt
moderation to about 12K interrupts per second for ixgbe. This change
increases the performance for ixgbe. Also fixed up fm10k to remove
the optimization that assumed that all fragments would be limited to
page size, since that assumption is incorrect as the TCP allocator can
provide up to a 32K page fragment. Updated fm10k to add the MAC
address to the list of values recorded on driver load. Fixes fm10k
so that we only trigger the data path reset if the fabric is ready to
handle traffic to avoid triggering the reset unless the switch API is
ready for us.
Jacob updates the fm10k driver to disable the service task during
suspend and re-enable it after we resume. If we don't do this, the
device could be UP when you suspend and come back from resume as
DOWN. Also update fm10k to prevent the removal of default VID rules,
and correctly remove the stack layers information of the VLAN, but then
return to forwarding that VID as untagged frames. If we deleted the VID
rules here, we would begin dropping traffic due to VLAN membership
violations. Fixed fm10k to use pcie_get_minimum_link(), which is useful
in cases where we connect to a slot at Gen3, but the slot is behind a bus
which is only connected at Gen2. Updated fm10k to update the netdev
permanent address during reinit instead of up to enable users to
immediately see the new MAC address on the VF even if the device is not
up. Adds the creation of VLAN interfaces on a device, even while the
device is down for fm10k. Fixed an issue where we request the incorrect
MAC/VLAN combinations, and prevents us from accidentally reporting some
frames as VLAN tagged. Provided a couple of trivial fixes for fm10k
to fix code style and typos in code comments.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
Redo commit ed1acc8cd8c22efa919da8d300bab646e01c2dce.
Commit 822b3b2ebfff8e9b3d006086c527738a7ca00cd0 ("net: Add max rate tx queue
attribute") moved get_netdev_queue_index around, but kept the old version.
Probably because of a reuse of the original patch from before Eric's change to
that function.
Remove one inline keyword, and no need for a loop to find
an index into a table.
Signed-off-by: Thadeu Lima de Souza Cascardo <[email protected]>
Fixes: 822b3b2ebfff ("net: Add max rate tx queue attribute")
Acked-by: Or Gerlitz <[email protected]>
Acked-by: John Fastabend <[email protected]>
Cc: Eric Dumazet <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Convert the dma transfers to be dmaengine based, now pxa has a dmaengine
slave driver. This makes this driver a bit more PXA agnostic.
The driver was tested on pxa27x (mainstone) and pxa310 (zylonite),
ie. only pxa platforms.
Signed-off-by: Robert Jarzmik <[email protected]>
Cc: Russell King <[email protected]>
Cc: Arnd Bergmann <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This was missed in the original commit adding the flag and ath10k only printed "bit10":
ath10k_pci 0000:02:00.0: qca988x hw2.0 (0x4100016c, 0x043202ff) fw 10.2.4.70.6-2 api 3
htt-ver 2.1 wmi-op 5 htt-op 2 cal otp max-sta 128 raw 0 hwcrypto 1 features no-p2p,bit10
Also add a build test to avoid this happening again.
Fixes: ccec9038c721 ("ath10k: enable raw encap mode and software crypto engine")
Signed-off-by: Kalle Valo <[email protected]>
|
|
Vdevs associated with a given chanctx should be
restarted if the bandwidth changes. Otherwise
traffic may cease.
This is known to fix STA CSA with bandwidths wider
than 20MHz.
Signed-off-by: Michal Kazior <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
This is necessary to make vdev restarting logic
reusable later.
Signed-off-by: Michal Kazior <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
The remain_on_channel callback needs different
timeout. Calling ieee80211_queue_work() with a
shorter delay after calling it with a longer delay
will not change the timer. This caused the
offchannel timeout worker to not trigger in time
and caused the device to stay on channel longer
then expected. This could cause some problems and
was be easily reproduced with `iw offchannel`
command.
Signed-off-by: Michal Kazior <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
Add support for mesh to ath10k. We simply use an AP virtual interface
in the firmware in order to enable beaconing without TSF adoption, and
use the raw (802.11) transmit mode.
Due to firmware limitations, the firmware must operate in raw
(non-native 802.11) mode. As this is configured at firmware init time,
a new "rawmode" modparam is added, and mesh interfaces are available
only if rawmode=true. The firmware must advertise support for rawmode;
tested successfully with firmware 10.2.4.70.6-2.
When the module is loaded with (newly implemented) modparam rawmode=1, it
will enable operating an open mesh STA via something like the following:
ip link set wlan0 down
iw dev wlan0 set type mp
ip link set wlan0 up
iw dev wlan0 set freq 5745 80 5775
iw dev wlan0 mesh join mesh-vht
Signed-off-by: Bob Copeland <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
In the case of raw mode without nohwcrypt parameter, we
should still make sure the frame is protected before
adding MIC_LEN to avoid skb_under_panic errors.
Signed-off-by: Bob Copeland <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
By default, ath10k restricts received frames to those matching BSSID.
When other BSS frames are requested (e.g. in mesh mode), add an internal
monitor device so those frames are not filtered.
Signed-off-by: Bob Copeland <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
Fix build error caused by missing Kconfig dependency:
ERROR: "cdc_parse_cdc_header" [drivers/net/usb/cdc-phonet.ko] undefined!
Reported-by: Fengguang Wu <[email protected]>
Signed-off-by: Randy Dunlap <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Signed-off-by: Stephen Rothwell <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The VF will send a message to request multicast addresses with the
default VID. In the current code, if the PF has statically assigned a
VLAN to a VF, then the VF will not get the multicast addresses. Fix up
all of the various VLAN messages to use identical checks (since each
check was different). Also use set as a variable, so that it simplifies
our check for whether VLAN matches the pf_vid.
The new logic will allow set of a VLAN if it is zero, automatically
converting to the default VID. Otherwise it will allow setting the PF
VID, or any VLAN if PF has not statically assigned a VLAN. This is
consistent behavior, and allows VF to request either 0 or the
default_vid without silently failing.
Note that we need the check for zero since VFs might not get the default
VID message in time to actually request non-zero VLANs.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Krishneil Singh <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
This change makes it so that we only trigger the data path reset if the
fabric is ready to handle traffic. The general idea is to avoid
triggering the reset unless the switch API is ready for us. Otherwise
we can just postpone the reset until we receive a switch ready
notification.
Signed-off-by: Alexander Duyck <[email protected]>
Signed-off-by: Jacob Keller <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
Modify behavior of Malicious Driver Detection events. Presently, the
hardware disables the VF queues and re-assigns them to the PF. This
causes the VF in question to continuously Tx hang, because it assumes
that it can transmit over the queues in question. For transient events,
this results in continuous logging of malicious events.
New behavior is to reset the LPORT and VF state, so that the VF will
have to reset and re-enable itself. This does mean that malicious VFs
will possibly be able to continue and attempt malicious events again.
However, it is expected that system administrators will step in and
manually remove or disable the VF in question.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Krishneil Singh <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
Signed-off-by: Jacob Keller <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
This patch ensures that VLAN traffic on the default VID will go to the
corresponding VLAN device if it exists. To do this, mask the rx_ring VID
if we have an active VLAN on that VID.
For this to work correctly, we need to update fm10k_process_skb_fields
to correctly mask off the VLAN_PRIO_MASK bits and compare them
separately, otherwise we incorrectly compare the priority bits with the
cleared flag. This also happens to fix a related bug where having
priority bits set causes us to incorrectly classify traffic.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Krishneil Singh <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
Fix some style issues in debugfs code, and correct ordering of void and
__always_unused. Technically, the order does not matter, but preferred
style is to put the macro between the type and name.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Krishneil Singh <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
This function is no longer used now that we have updated fm10k_slot_warn
functionality.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Krishneil Singh <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
If we store the sw_vid at reset of PF, then we accidentally prevent the
VF from receiving the message to update its default VID. This only
occurs if the VF is created before the PF has come up, which is the
standard way of creating VFs when using the module parameter.
This fixes an issue where we request the incorrect MAC/VLAN
combinations, and prevents us from accidentally reporting some frames as
VLAN tagged.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Krishneil Singh <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
We re-sync upon going up, so there is little reason to worry about not
syncing immediately with switch. This prevents an error that occurs if
you add a VLAN interface while down.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Krishneil Singh <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
This change adds the MAC address to the list of values recorded on driver
load. The MAC address represents the serial number of the unit and allows
us to track the value should a card be replaced in a system.
The log message should now be similar in output to that of ixgbe.
Signed-off-by: Alexander Duyck <[email protected]>
Tested-by: Krishneil Singh <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
This change pulls out the optimization that assumed that all fragments
would be limited to page size. That hasn't been the case for some time now
and to assume this is incorrect as the TCP allocator can provide up to a
32K page fragment.
Signed-off-by: Alexander Duyck <[email protected]>
Acked-by: Jacob Keller <[email protected]>
Tested-by: Krishneil Singh <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
Update the netdev permanent address during fm10k_reinit enables the user
to immediately see the new MAC address on the VF even if the device
isn't up. The previous code required that the device by opened before
changes would appear.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Krishneil Singh <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
This is useful in cases where we connect to a slot at Gen3, but the slot
is behind a bus which only connected at Gen2. This generally only
happens when a PCIe switch is in the sequence of devices, and can be
very confusing when you see slow performance with no obvious cause.
I am aware this patch has a few lines that break 80 characters, but
there does not seem to be a readable way to format them to less than 80
characters. Suggestions welcome.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Krishneil Singh <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
This allows us to correctly add a VLAN even if it matches our default
VID. However, we don't want to remove the VID rules once that VLAN is
deleted. Correctly remove the stack layers information of the VLAN, but
then return to forwarding that VID as untagged frames. If we deleted the
VID rules here, we would begin dropping traffic due to VLAN membership
violations.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Krishneil Singh <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
The service task reads some registers as part of its normal routine,
even while the interface is down. Normally this is ok. However, during
suspend we have disabled the PCI device. Due to this, registers will
read in the same way as a surprise-remove event. Disable the service
task while we suspend, and re-enable it after we resume. If we don't do
this, the device could be UP when you suspend and come back from resume
as closed (since fm10k closes the device when it gets a surprise
remove).
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Krishneil Singh <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
This patch updates the lowest limit for adaptive interrupt interrupt
moderation to roughly 12K interrupts per second.
The way I came about reaching 12K as the desired interrupt rate is by
testing with UDP flows. Specifically I had a simple test that ran a
netperf UDP_STREAM test at varying sizes. What I found was as the packet
sizes increased the performance fell steadily behind until we were only
able to receive at ~4Gb/s with a message size of 65507. A bit of digging
found that we were dropping packets for the socket in the network stack,
and looking at things further what I found was I could solve it by increasing
the interrupt rate, or increasing the rmem_default/rmem_max. What I found was
that when the interrupt coalescing resulted in more data being processed
per interrupt than could be stored in the socket buffer we started losing
packets and the performance dropped. So I reached 12K based on the
following math.
rmem_default = 212992
skb->truesize = 2994
212992 / 2994 = 71.14 packets to fill the buffer
packet rate at 1514 packet size is 812744pps
71.14 / 812744 = 87.9us to fill socket buffer
From there it was just a matter of choosing the interrupt rate and
providing a bit of wiggle room which is why I decided to go with 12K
interrupts per second as that uses a value of 84us.
The data below is based on VM to VM over a direct assigned ixgbe interface.
The test run was:
netperf -H <ip> -t UDP_STREAM"
Socket Message Elapsed Messages CPU Service
Size Size Time Okay Errors Throughput Util Demand
bytes bytes secs # # 10^6bits/sec % SS us/KB
Before:
212992 65507 60.00 1100662 0 9613.4 10.89 0.557
212992 60.00 473474 4135.4 11.27 0.576
After:
212992 65507 60.00 1100413 0 9611.2 10.73 0.549
212992 60.00 974132 8508.3 11.69 0.598
Using bare metal the data is similar but not as dramatic as the throughput
increases from about 8.5Gb/s to 9.5Gb/s.
Signed-off-by: Alexander Duyck <[email protected]>
Tested-by: Krishneil Singh <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
When the .remove() callback for a PF is called, SR-IOV support for the
device is disabled, which requires unbinding and removing the VFs.
The VFs may be in-use either by the host kernel or userspace, such as
assigned to a VM through vfio-pci. In this latter case, the VFs may
be removed either by shutting down the VM or hot-unplugging the
devices from the VM. Unfortunately in the case of a Windows 2012 R2
guest, hot-unplug is broken due to the ordering of the PF driver
teardown. Disabling SR-IOV prior to unregister_netdev() avoids this
issue.
Signed-off-by: Alex Williamson <[email protected]>
Acked-by: Mitch Williams <[email protected]>
Tested-by: Krishneil Singh <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
Add checks for systems that don't have SFP's to avoid incorrectly
acting on interrupts that are falsely interpreted as SFP events.
This also includes a modified check generating the EICR mask to be
more forward-looking.
Signed-off-by: Don Skidmore <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
Many commonly used functions like getifaddrs() invoke RTM_GETLINK
to dump the interface information, and do not need the
the AF_INET6 statististics that are always returned by default
from rtnl_fill_ifinfo().
Computing the statistics can be an expensive operation that impacts
scaling, so it is desirable to avoid this if the information is
not needed.
This patch adds a the RTEXT_FILTER_SKIP_STATS extended info flag that
can be passed with netlink_request() to avoid statistics computation
for the ifinfo path.
Signed-off-by: Sowmini Varadhan <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In file included from drivers/usb/gadget/function/u_serial.h:16:0,
from drivers/usb/gadget/function/f_acm.c:23:
>> include/linux/usb/cdc.h:47:5: warning: 'struct usb_interface' declared inside parameter list
int buflen);
^
>> include/linux/usb/cdc.h:47:5: warning: its scope is only this definition or declaration, which is probably not what you want
Reported-by: kbuild test robot <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The code around the allocation and loops are a bit obfuscated.
Neaten it by using:
o kcalloc with decimal count and sizeof(u32)
o Decimal loop indexing and i++ not i += 4
o A promiscuous block using a similar style
to the multicast block
o Remove unnecessary variables
Signed-off-by: Joe Perches <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|