| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This reverts commit 8a91b29f1f50ce7742cdbe5cf11d17f128511f3f.
The regulator_disable() added by the original commit solves one kind of
regulator imbalance but adds another one as it allows the regulator to be
disabled one more time than it is enabled in the following scenario:
1. Start video pipeline -> sn65dsi83_atomic_pre_enable -> regulator_enable
2. PLL lock fails -> regulator_disable
3. Stop video pipeline -> sn65dsi83_atomic_disable -> regulator_disable
The reason is clear from the code flow, which looks like this (after
removing unrelated code):
static void sn65dsi83_atomic_pre_enable()
{
regulator_enable(ctx->vcc);
if (PLL failed locking) {
regulator_disable(ctx->vcc); <---- added by patch being reverted
return;
}
}
static void sn65dsi83_atomic_disable()
{
regulator_disable(ctx->vcc);
}
The use case for introducing the additional regulator_disable() was
removing the module for debugging (see link below for the discussion). If
the module is removed after a .atomic_pre_enable, i.e. with an active
pipeline from the DRM point of view, .atomic_disable is not called and thus
the regulator would not be disabled.
According to the discussion however there is no actual use case for
removing the module with an active pipeline, except for
debugging/development.
On the other hand, the occurrence of a PLL lock failure is possible due to
any physical reason (e.g. a temporary hardware failure for electrical
reasons) so handling it gracefully should be supported. As there is no way
for .atomic[_pre]_enable to report an error to the core, the only clean way
to support it is calling regulator_disabled() only in .atomic_disable,
unconditionally, as it was before.
Link: https://lore.kernel.org/all/15244220.uLZWGnKmhe@steina-w/
Fixes: 8a91b29f1f50 ("drm/bridge: ti-sn65dsi83: Fix enable error path")
Reviewed-by: Alexander Stein <[email protected]>
Signed-off-by: Luca Ceresoli <[email protected]>
Signed-off-by: Robert Foss <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
(cherry picked from commit 2940ee03b23281071620dda1d790cd644dabd394)
Signed-off-by: Maarten Lankhorst <[email protected]>
|
|
plane->state and plane->state->fb can be NULL, so add a check before
dereferencing them.
Found by testing with the imx driver.
Fixes: 879b3b6511fe ("drm/fb_dma: Add generic get_scanout_buffer() for drm_panic")
Signed-off-by: Jocelyn Falempe <[email protected]>
Reviewed-by: Thomas Zimmermann <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
(cherry picked from commit 986c12d8c9a677c094c37bd6aa636b4d4c5ccd46)
Signed-off-by: Maarten Lankhorst <[email protected]>
|
|
Framebuffer memory is allocated via vzalloc() from non-contiguous
physical pages. The physical framebuffer start address is therefore
meaningless. Do not set it.
The value is not used within the kernel and only exported to userspace
on dedicated ARM configs. No functional change is expected.
v2:
- refer to vzalloc() in commit message (Javier)
Signed-off-by: Thomas Zimmermann <[email protected]>
Fixes: a5b44c4adb16 ("drm/fbdev-generic: Always use shadow buffering")
Cc: Thomas Zimmermann <[email protected]>
Cc: Javier Martinez Canillas <[email protected]>
Cc: Zack Rusin <[email protected]>
Cc: Maarten Lankhorst <[email protected]>
Cc: Maxime Ripard <[email protected]>
Cc: <[email protected]> # v6.4+
Reviewed-by: Javier Martinez Canillas <[email protected]>
Reviewed-by: Zack Rusin <[email protected]>
Reviewed-by: Sui Jingfeng <[email protected]>
Tested-by: Sui Jingfeng <[email protected]>
Acked-by: Maxime Ripard <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
(cherry picked from commit 73ef0aecba78aa9ebd309b10b6cd17d94e632892)
Signed-off-by: Maarten Lankhorst <[email protected]>
|
|
In the post_reset function, if the fast reset didn't succeed, we
are not clearing the fast_reset flag, which prevents firmware
sections from being reloaded. While at it, use panthor_fw_stop()
instead of manually writing DISABLE to the MCU_CONTROL register.
Fixes: 2718d91816ee ("drm/panthor: Add the FW logical block")
Signed-off-by: Boris Brezillon <[email protected]>
Reviewed-by: Liviu Dudau <[email protected]>
Reviewed-by: Steven Price <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
When we check for state values returned by the FW, we only cover part of
the 0:7 range. Make sure we catch FW inconsistencies by adding a default
to the switch statement, and flagging the group state as unknown in that
case.
When an unknown state is detected, we trigger a reset, and consider the
group as unusable after that point, to prevent the potential corruption
from creeping in other places if we continue executing stuff on this
context.
v2:
- Add Steve's R-b
- Fix commit message
Reported-by: Dan Carpenter <[email protected]>
Closes: https://lore.kernel.org/dri-devel/[email protected]/T/#u
Suggested-by: Steven Price <[email protected]>
Signed-off-by: Boris Brezillon <[email protected]>
Reviewed-by: Steven Price <[email protected]>
Reviewed-by: Liviu Dudau <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
When you create a submenu using the 'menu' syntax, there is no
ambiguity about its end because the code between 'menu' and 'endmenu'
becomes the submenu.
In contrast, 'menuconfig' does not have the corresponding end marker.
Instead, the end of the submenu is inferred from symbol dependencies.
This is detailed in Documentation/kbuild/kconfig-language.rst, starting
line 348. It outlines two methods to place the code under the submenu:
(1) Open an if-block immediately after 'menuconfig', enclosing the
submenu content within it
(2) Add 'depends on' to every symbol intended for the submenu
Many subsystems opt for (1) because it reliably maintains the submenu
structure.
The DRM subsystem adopts (2). The submenu ends when the sequence of
'depends on DRM' breaks. It can be confirmed by running a GUI frontend
such as 'make menuconfig' and visiting the DRM menu:
< > Direct Rendering Manager (XFree86 4.1.0 and higher DRI support) ----
If you toggle this, you will notice most of the DRM-related options
appear below it, not in the submenu.
I highly recommend the approach (1). Obviously, (2) is not reliable,
as the submenu breaks whenever someone forgets to add 'depends on DRM'.
This commit encloses the entire DRM configuration with 'if DRM' and
'endif', except for DRM_PANEL_ORIENTATION_QUIRKS.
Note:
Now, 'depends on DRM' properties inside the if-block are all redundant.
I leave it as follow-up cleanups.
Signed-off-by: Masahiro Yamada <[email protected]>
Acked-by: Arnd Bergmann <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Signed-off-by: Maxime Ripard <[email protected]>
|
|
This reverts commit d674858ff979550a0e97b4ac766f2640f0d9d7e7, as helper
code should always be selected by the driver that needs it, for the
convenience of the final user configuring a kernel.
The user who configures a kernel should not need to know which helpers
are needed for the driver he is interested in. Making a driver depend
on helper code means that the user needs to know which helpers to enable
first, which is very user-unfriendly.
Signed-off-by: Geert Uytterhoeven <[email protected]>
Acked-by: Arnd Bergmann <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/3db958e3f4002e26cd963596d810c37feb315fb3.1713780345.git.geert+renesas@glider.be
Signed-off-by: Maxime Ripard <[email protected]>
|
|
This reverts commit c0e0f139354c01e0213204e4a96e7076e5a3e396, as helper
code should always be selected by the driver that needs it, for the
convenience of the final user configuring a kernel.
The user who configures a kernel should not need to know which helpers
are needed for the driver he is interested in. Making a driver depend
on helper code means that the user needs to know which helpers to enable
first, which is very user-unfriendly.
Signed-off-by: Geert Uytterhoeven <[email protected]>
Acked-by: Arnd Bergmann <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/bd93d43b07f8ed6368119f4a5ddac2ee80debe53.1713780345.git.geert+renesas@glider.be
Signed-off-by: Maxime Ripard <[email protected]>
|
|
This reverts commit e075e496f516bf92bc0cbaf94d64e8d4a6b58321, as helper
code should always be selected by the driver that needs it, for the
convenience of the final user configuring a kernel.
The user who configures a kernel should not need to know which helpers
are needed for the driver he is interested in. Making a driver depend
on helper code means that the user needs to know which helpers to enable
first, which is very user-unfriendly.
Signed-off-by: Geert Uytterhoeven <[email protected]>
Acked-by: Arnd Bergmann <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/1ba76cc4d96a8afefff5d1bc42fb1e1329c5da68.1713780345.git.geert+renesas@glider.be
Signed-off-by: Maxime Ripard <[email protected]>
|
|
This reverts commit 4d15125d7fe637f401e64e33c99513adf6586fdd, as helper
code should always be selected by the driver that needs it, for the
convenience of the final user configuring a kernel.
The user who configures a kernel should not need to know which helpers
are needed for the driver he is interested in. Making a driver depend
on helper code means that the user needs to know which helpers to enable
first, which is very user-unfriendly.
Signed-off-by: Geert Uytterhoeven <[email protected]>
Acked-by: Arnd Bergmann <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/79824fec01eb9ab0673b9409f9b39cc8b5cc338d.1713780345.git.geert+renesas@glider.be
Signed-off-by: Maxime Ripard <[email protected]>
|
|
This reverts commit 0323287de87d7e6e9c22c57d7440aa353a2298d0, as helper
code should always be selected by the driver that needs it, for the
convenience of the final user configuring a kernel.
The user who configures a kernel should not need to know which helpers
are needed for the driver he is interested in. Making a driver depend
on helper code means that the user needs to know which helpers to enable
first, which is very user-unfriendly.
Signed-off-by: Geert Uytterhoeven <[email protected]>
Acked-by: Arnd Bergmann <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/89ac456805746b6d0c888f10c5120b11aacd3319.1713780345.git.geert+renesas@glider.be
Signed-off-by: Maxime Ripard <[email protected]>
|
|
This reverts commit 3166e7e6d935caaef07605a5c90773fbf9ffeaf4, as helper
code should always be selected by the driver that needs it, for the
convenience of the final user configuring a kernel.
The user who configures a kernel should not need to know which helpers
are needed for the driver he is interested in. Making a driver depend
on helper code means that the user needs to know which helpers to enable
first, which is very user-unfriendly.
Signed-off-by: Geert Uytterhoeven <[email protected]>
Acked-by: Arnd Bergmann <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/a40e70a0abd3d841c23c107d452a43fdd70ef37a.1713780345.git.geert+renesas@glider.be
Signed-off-by: Maxime Ripard <[email protected]>
|
|
This reverts commit f6d2dc03fa8546b284dd8c1af027d9fac5725921, as helper
code should always be selected by the driver that needs it, for the
convenience of the final user configuring a kernel.
The user who configures a kernel should not need to know which helpers
are needed for the driver he is interested in. Making a driver depend
on helper code means that the user needs to know which helpers to enable
first, which is very user-unfriendly.
Signed-off-by: Geert Uytterhoeven <[email protected]>
Acked-by: Arnd Bergmann <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/bd288a5943dab8609f2d1f2bf413595a61df727a.1713780345.git.geert+renesas@glider.be
Signed-off-by: Maxime Ripard <[email protected]>
|
|
This reverts commit d1ef8fc18be6adbbffdee06fbb5b33699e2852be, as the
commit it fixes will be reverted, too.
Signed-off-by: Geert Uytterhoeven <[email protected]>
Acked-by: Arnd Bergmann <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/df2876c72e82cbecfe8406fa058e8d3e895e4b93.1713780345.git.geert+renesas@glider.be
Signed-off-by: Maxime Ripard <[email protected]>
|
|
This reverts commit 0209df3b4731516fe77638bfc52ba2e9629c67cd, as the
commit it fixes (which is BTW not the commit in the Fixes: tag!) will be
reverted, too.
Signed-off-by: Geert Uytterhoeven <[email protected]>
Acked-by: Arnd Bergmann <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/b2d1a7a765e4af249f4c450383de6e8422647e2e.1713780345.git.geert+renesas@glider.be
Signed-off-by: Maxime Ripard <[email protected]>
|
|
This reverts commit 7fa678cc0a5648b5ea28629a2d21b9d4b6ac8f56, as the
commit it fixes will be reverted, too.
Signed-off-by: Geert Uytterhoeven <[email protected]>
Acked-by: Arnd Bergmann <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/17b6a2c5f3250a7d02ee1b517182ca6fd9baa45a.1713780345.git.geert+renesas@glider.be
Signed-off-by: Maxime Ripard <[email protected]>
|
|
This reverts commit a57e191ebbaa0363dbf352cc37447c2230573e29, as the
commits it fixes will be reverted, too.
Signed-off-by: Geert Uytterhoeven <[email protected]>
Acked-by: Arnd Bergmann <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/37216404c77b4c677d3b3a80d12d6d4447a3f3a0.1713780345.git.geert+renesas@glider.be
Signed-off-by: Maxime Ripard <[email protected]>
|
|
We can use upd_ctx.timedout_mask directly, and the faulty_slots update
in the flush_caches_failed situation is never used.
Suggested-by: Suggested-by: Steven Price <[email protected]>
Signed-off-by: Boris Brezillon <[email protected]>
Reviewed-by: Steven Price <[email protected]>
Reviewed-by: Liviu Dudau <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
In order to detect duplicate implementations for the same workaround,
early in the implementation of RTP it was decided to error out even if
the values set are exactly the same. With the introduction of 18034896535
in commit 74671d23ca18 ("drm/xe/xe2: Add workaround 18034896535"), LNL
stepping with graphics stepping A1 now gives the following error on
module load:
xe 0000:00:02.0: [drm] *ERROR* GT0: [GT OTHER] \
discarding save-restore reg e48c (clear: 00000200, set: 00000200,\
masked: yes, mcr: yes): ret=-22
RTP may be improved in the future, but for now simply join the entries
like done with e.g. "1607297627, 1607030317, 1607186500".
Fixes: 74671d23ca18 ("drm/xe/xe2: Add workaround 18034896535")
Cc: Bommu Krishnaiah <[email protected]>
Cc: Tejas Upadhyay <[email protected]>
Cc: Matt Roper <[email protected]>
Reviewed-by: Himal Prasad Ghimiray <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Signed-off-by: Lucas De Marchi <[email protected]>
(cherry picked from commit 4caf410766add8cf376a3afc910b17dd0961dd75)
Signed-off-by: Thomas Hellström <[email protected]>
|
|
We flush the rebind worker during the vm close phase, however in places
like preempt_fence_work_func() we seem to queue the rebind worker
without first checking if the vm has already been closed. The concern
here is the vm being closed with the worker flushed, but then being
rearmed later, which looks like potential uaf, since there is no actual
refcounting to track the queued worker. We can't take the vm->lock here
in preempt_rebind_work_func() to first check if the vm is closed since
that will deadlock, so instead flush the worker again when the vm
refcount reaches zero.
v2:
- Grabbing vm->lock in the preempt worker creates a deadlock, so
checking the closed state is tricky. Instead flush the worker when
the refcount reaches zero. It should be impossible to queue the
preempt worker without already holding vm ref.
Fixes: dd08ebf6c352 ("drm/xe: Introduce a new DRM driver for Intel GPUs")
Closes: https://gitlab.freedesktop.org/drm/xe/kernel/-/issues/1676
Closes: https://gitlab.freedesktop.org/drm/xe/kernel/-/issues/1591
Closes: https://gitlab.freedesktop.org/drm/xe/kernel/-/issues/1364
Closes: https://gitlab.freedesktop.org/drm/xe/kernel/-/issues/1304
Closes: https://gitlab.freedesktop.org/drm/xe/kernel/-/issues/1249
Signed-off-by: Matthew Auld <[email protected]>
Cc: Matthew Brost <[email protected]>
Cc: <[email protected]> # v6.8+
Reviewed-by: Matthew Brost <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
(cherry picked from commit 3d44d67c441a9fe6f81a1d705f7de009a32a5b35)
Signed-off-by: Thomas Hellström <[email protected]>
|
|
The recent backmerge from drm-next to drm-xe-next brought with it
some silent unexpected results. One code snippet was added twice
and a partial revert had merge errors. Fix that up to
reinstate the affected code as it was before the backmerge.
v2:
- Commit log message rewording (Lucas DeMarchi)
Fixes: 79790b6818e9 ("Merge drm/drm-next into drm-xe-next")
Signed-off-by: Thomas Hellström <[email protected]>
Reviewed-by: Matthew Brost <[email protected]>
Reviewed-by: Lucas De Marchi <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
(cherry picked from commit 06e7139a034f26804904368fe4af2ceb70724756)
Signed-off-by: Thomas Hellström <[email protected]>
|
|
In one case the -1 is returned which is quite confusing code for
the wrong device ID, in another the ret is returning instead of
plain 0 that also confusing as readed may ask the possible meaning
of positive codes, which are never the case there. Convert both
to use explicit predefined error codes to make it clear what's going
on there.
Fixes: 5a04227326b0 ("drm/panel: Add ilitek ili9341 panel driver")
Signed-off-by: Andy Shevchenko <[email protected]>
Reviewed-by: Neil Armstrong <[email protected]>
Reviewed-by: Sui Jingfeng <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Neil Armstrong <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
GPIO controller might not be available when driver is being probed.
There are plenty of reasons why, one of which is deferred probe.
Since GPIOs are optional, return any error code we got to the upper
layer, including deferred probe. With that in mind, use dev_err_probe()
in order to avoid spamming the logs.
Fixes: 5a04227326b0 ("drm/panel: Add ilitek ili9341 panel driver")
Signed-off-by: Andy Shevchenko <[email protected]>
Reviewed-by: Dmitry Baryshkov <[email protected]>
Reviewed-by: Neil Armstrong <[email protected]>
Reviewed-by: Sui Jingfeng <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Neil Armstrong <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
It seems driver missed the point of proper use of device property APIs.
Correct this by updating headers and calls respectively.
Fixes: 5a04227326b0 ("drm/panel: Add ilitek ili9341 panel driver")
Signed-off-by: Andy Shevchenko <[email protected]>
Reviewed-by: Dmitry Baryshkov <[email protected]>
Reviewed-by: Neil Armstrong <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Neil Armstrong <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
https://anongit.freedesktop.org/git/drm/drm-intel into drm-next
Core DRM:
- Export drm_client_dev_unregister (Thomas Zimmermann)
Display i915:
- More initial work to make display code more independent from i915 (Jani)
- Convert i915/xe fbdev to DRM client (Thomas Zimmermann)
- VLV/CHV DPIO register cleanup (Ville)
Signed-off-by: Dave Airlie <[email protected]>
From: Rodrigo Vivi <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Pull the VLV/CHV DPIO PHY sideband registers to their own file.
v2: drop stray tabs (Jani)
Signed-off-by: Ville Syrjälä <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Reviewed-by: Jani Nikula <[email protected]>
|
|
Use REG_BIT() & co. for the vlv/chv DPIO PHY registers.
Note that DPIO_BIAS_CURRENT_CTL_SHIFT was incorrectly defined
to be 21 wheres 20 is the correct value. It is not used in the
code though so didn't bother splitting to a separate patch.
v2: drop stray tabs (Jani)
Signed-off-by: Ville Syrjälä <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Reviewed-by: Jani Nikula <[email protected]>
|
|
The DPIO PHY registers follow clear numbering rules. Express
those in a few macros to get rid of the hand calculated
final offsets.
Signed-off-by: Ville Syrjälä <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Reviewed-by: Jani Nikula <[email protected]>
|
|
Drop the leading underscore from the CHV PHY common lane
register definitions. We use these directly from actual
code so the underscore here is misleading as usually it indicates
an intermediate define that shouldn't be used directly.
Signed-off-by: Ville Syrjälä <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Reviewed-by: Jani Nikula <[email protected]>
|
|
Include _GRP in VLV DPIO PHY group access register define
names. Makes it more obvious where the accesses will land.
Also matches the naming used by BXT already.
Signed-off-by: Ville Syrjälä <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Reviewed-by: Jani Nikula <[email protected]>
|
|
In the encoder hooks we are dealing primarily with the encoder,
so derive the DPIO PHY from the encoder rather than the pipe.
Technically this doesn't matter as we can't cross connect
pipes<->port across PHY boundaries, but it does conveny the
intention more accurately.
Signed-off-by: Ville Syrjälä <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Reviewed-by: Jani Nikula <[email protected]>
|
|
Stop using 'pipe' directly as the DPIO PHY channel. This
does happen to work on VLV since it just has the one PHY
with CH0==pipe A and CH1==pipe B. But explicitly converting
the thing to the right enum makes the whole thing less
confusing.
Signed-off-by: Ville Syrjälä <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Reviewed-by: Jani Nikula <[email protected]>
|
|
Stop calling the DPIO PHY channel "port". Just say "ch", which
is already used in a bunch of places.
Signed-off-by: Ville Syrjälä <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Reviewed-by: Jani Nikula <[email protected]>
|
|
Use a consistent 'tmp' as the variable name for the register
values during rmw when we don't deal with multiple registers
in parallel.
Signed-off-by: Ville Syrjälä <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Reviewed-by: Jani Nikula <[email protected]>
|
|
Drop all the local variables for the DPLL dividers for vlv/chv
and just consult the state directly.
Signed-off-by: Ville Syrjälä <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Reviewed-by: Jani Nikula <[email protected]>
|
|
The spreadsheet defines the PLL register block as having
the dwords in the following order:
block dwords offsets
PLL1 0x0-0x7 0x00-0x1f
PLL2 0x0-0x7 0x20-0x3f
PLL1ext 0x10-0x1f 0x40-0x5f
PLL2ext 0x10-0x1f 0x60-0x7f
So dword indexes 0x8-0xf don't even exist. Renumber
our register defines to match.
Note that the spreadsheet used hex numbering whereas our
defiens are in decimal. Perhaps we should change that?
Signed-off-by: Ville Syrjälä <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Reviewed-by: Jani Nikula <[email protected]>
|
|
VLV_PLL_DW9_BCAST is actually VLV_PCS_DW17_BCAST. The address
does kinda look like it goes to the PLL block on a first glance,
but broadcast is special and doesn't even exist for the PLL
(only PCS and TX have it).
The fact that we use a broadcast write here is a bit sketchy
IMO since we're now blasting the register to all PCS splines
across the whole PHY. So the PCS registers in the other channel
(ie. other pipe/port) will also be written. But I guess the
fact that we always write the same value should make this a nop
even if the other channel is already enabled (assuming the VBIOS/GOP
didn't screw up and use some other value...).
Signed-off-by: Ville Syrjälä <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Reviewed-by: Jani Nikula <[email protected]>
|
|
Our VLV_REF_DW13 is actually VLV_REF_DW11. Rename it.
Signed-off-by: Ville Syrjälä <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Reviewed-by: Jani Nikula <[email protected]>
|
|
We don't use the result of the VLV_PCS01_DW8 read at all,
so don't read.
Signed-off-by: Ville Syrjälä <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Reviewed-by: Jani Nikula <[email protected]>
|
|
Correctly set the length of the drm_event to the size of the structure
that's actually used.
The length of the drm_event was set to the parent structure instead of
to the drm_vmw_event_fence which is supposed to be read. drm_read
uses the length parameter to copy the event to the user space thus
resuling in oob reads.
Signed-off-by: Zack Rusin <[email protected]>
Fixes: 8b7de6aa8468 ("vmwgfx: Rework fence event action")
Reported-by: [email protected] # ZDI-CAN-23566
Cc: David Airlie <[email protected]>
CC: Daniel Vetter <[email protected]>
Cc: Zack Rusin <[email protected]>
Cc: Broadcom internal kernel review list <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: <[email protected]> # v3.4+
Reviewed-by: Maaz Mombasawala <[email protected]>
Reviewed-by: Martin Krastev <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Currently we allocate all 3 levels of radix3 page tables using
nvkm_gsp_mem_ctor(), which uses dma_alloc_coherent() for allocating all of
the relevant memory. This can end up failing in scenarios where the system
has very high memory fragmentation, and we can't find enough contiguous
memory to allocate level 2 of the page table.
Currently, this can result in runtime PM issues on systems where memory
fragmentation is high - as we'll fail to allocate the page table for our
suspend/resume buffer:
kworker/10:2: page allocation failure: order:7, mode:0xcc0(GFP_KERNEL),
nodemask=(null),cpuset=/,mems_allowed=0
CPU: 10 PID: 479809 Comm: kworker/10:2 Not tainted
6.8.6-201.ChopperV6.fc39.x86_64 #1
Hardware name: SLIMBOOK Executive/Executive, BIOS N.1.10GRU06 02/02/2024
Workqueue: pm pm_runtime_work
Call Trace:
<TASK>
dump_stack_lvl+0x64/0x80
warn_alloc+0x165/0x1e0
? __alloc_pages_direct_compact+0xb3/0x2b0
__alloc_pages_slowpath.constprop.0+0xd7d/0xde0
__alloc_pages+0x32d/0x350
__dma_direct_alloc_pages.isra.0+0x16a/0x2b0
dma_direct_alloc+0x70/0x270
nvkm_gsp_radix3_sg+0x5e/0x130 [nouveau]
r535_gsp_fini+0x1d4/0x350 [nouveau]
nvkm_subdev_fini+0x67/0x150 [nouveau]
nvkm_device_fini+0x95/0x1e0 [nouveau]
nvkm_udevice_fini+0x53/0x70 [nouveau]
nvkm_object_fini+0xb9/0x240 [nouveau]
nvkm_object_fini+0x75/0x240 [nouveau]
nouveau_do_suspend+0xf5/0x280 [nouveau]
nouveau_pmops_runtime_suspend+0x3e/0xb0 [nouveau]
pci_pm_runtime_suspend+0x67/0x1e0
? __pfx_pci_pm_runtime_suspend+0x10/0x10
__rpm_callback+0x41/0x170
? __pfx_pci_pm_runtime_suspend+0x10/0x10
rpm_callback+0x5d/0x70
? __pfx_pci_pm_runtime_suspend+0x10/0x10
rpm_suspend+0x120/0x6a0
pm_runtime_work+0x98/0xb0
process_one_work+0x171/0x340
worker_thread+0x27b/0x3a0
? __pfx_worker_thread+0x10/0x10
kthread+0xe5/0x120
? __pfx_kthread+0x10/0x10
ret_from_fork+0x31/0x50
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1b/0x30
Luckily, we don't actually need to allocate coherent memory for the page
table thanks to being able to pass the GPU a radix3 page table for
suspend/resume data. So, let's rewrite nvkm_gsp_radix3_sg() to use the sg
allocator for level 2. We continue using coherent allocations for lvl0 and
1, since they only take a single page.
V2:
* Don't forget to actually jump to the next scatterlist when we reach the
end of the scatterlist we're currently on when writing out the page table
for level 2
Signed-off-by: Lyude Paul <[email protected]>
Cc: [email protected]
Reviewed-by: Ben Skeggs <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Currently, enabling SG_DEBUG in the kernel will cause nouveau to hit a
BUG() on startup:
kernel BUG at include/linux/scatterlist.h:187!
invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
CPU: 7 PID: 930 Comm: (udev-worker) Not tainted 6.9.0-rc3Lyude-Test+ #30
Hardware name: MSI MS-7A39/A320M GAMING PRO (MS-7A39), BIOS 1.I0 01/22/2019
RIP: 0010:sg_init_one+0x85/0xa0
Code: 69 88 32 01 83 e1 03 f6 c3 03 75 20 a8 01 75 1e 48 09 cb 41 89 54
24 08 49 89 1c 24 41 89 6c 24 0c 5b 5d 41 5c e9 7b b9 88 00 <0f> 0b 0f 0b
0f 0b 48 8b 05 5e 46 9a 01 eb b2 66 66 2e 0f 1f 84 00
RSP: 0018:ffffa776017bf6a0 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffffa77600d87000 RCX: 000000000000002b
RDX: 0000000000000001 RSI: 0000000000000000 RDI: ffffa77680d87000
RBP: 000000000000e000 R08: 0000000000000000 R09: 0000000000000000
R10: ffff98f4c46aa508 R11: 0000000000000000 R12: ffff98f4c46aa508
R13: ffff98f4c46aa008 R14: ffffa77600d4a000 R15: ffffa77600d4a018
FS: 00007feeb5aae980(0000) GS:ffff98f5c4dc0000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f22cb9a4520 CR3: 00000001043ba000 CR4: 00000000003506f0
Call Trace:
<TASK>
? die+0x36/0x90
? do_trap+0xdd/0x100
? sg_init_one+0x85/0xa0
? do_error_trap+0x65/0x80
? sg_init_one+0x85/0xa0
? exc_invalid_op+0x50/0x70
? sg_init_one+0x85/0xa0
? asm_exc_invalid_op+0x1a/0x20
? sg_init_one+0x85/0xa0
nvkm_firmware_ctor+0x14a/0x250 [nouveau]
nvkm_falcon_fw_ctor+0x42/0x70 [nouveau]
ga102_gsp_booter_ctor+0xb4/0x1a0 [nouveau]
r535_gsp_oneinit+0xb3/0x15f0 [nouveau]
? srso_return_thunk+0x5/0x5f
? srso_return_thunk+0x5/0x5f
? nvkm_udevice_new+0x95/0x140 [nouveau]
? srso_return_thunk+0x5/0x5f
? srso_return_thunk+0x5/0x5f
? ktime_get+0x47/0xb0
? srso_return_thunk+0x5/0x5f
nvkm_subdev_oneinit_+0x4f/0x120 [nouveau]
nvkm_subdev_init_+0x39/0x140 [nouveau]
? srso_return_thunk+0x5/0x5f
nvkm_subdev_init+0x44/0x90 [nouveau]
nvkm_device_init+0x166/0x2e0 [nouveau]
nvkm_udevice_init+0x47/0x70 [nouveau]
nvkm_object_init+0x41/0x1c0 [nouveau]
nvkm_ioctl_new+0x16a/0x290 [nouveau]
? __pfx_nvkm_client_child_new+0x10/0x10 [nouveau]
? __pfx_nvkm_udevice_new+0x10/0x10 [nouveau]
nvkm_ioctl+0x126/0x290 [nouveau]
nvif_object_ctor+0x112/0x190 [nouveau]
nvif_device_ctor+0x23/0x60 [nouveau]
nouveau_cli_init+0x164/0x640 [nouveau]
nouveau_drm_device_init+0x97/0x9e0 [nouveau]
? srso_return_thunk+0x5/0x5f
? pci_update_current_state+0x72/0xb0
? srso_return_thunk+0x5/0x5f
nouveau_drm_probe+0x12c/0x280 [nouveau]
? srso_return_thunk+0x5/0x5f
local_pci_probe+0x45/0xa0
pci_device_probe+0xc7/0x270
really_probe+0xe6/0x3a0
__driver_probe_device+0x87/0x160
driver_probe_device+0x1f/0xc0
__driver_attach+0xec/0x1f0
? __pfx___driver_attach+0x10/0x10
bus_for_each_dev+0x88/0xd0
bus_add_driver+0x116/0x220
driver_register+0x59/0x100
? __pfx_nouveau_drm_init+0x10/0x10 [nouveau]
do_one_initcall+0x5b/0x320
do_init_module+0x60/0x250
init_module_from_file+0x86/0xc0
idempotent_init_module+0x120/0x2b0
__x64_sys_finit_module+0x5e/0xb0
do_syscall_64+0x83/0x160
? srso_return_thunk+0x5/0x5f
entry_SYSCALL_64_after_hwframe+0x71/0x79
RIP: 0033:0x7feeb5cc20cd
Code: ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa 48 89 f8 48 89
f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0
ff ff 73 01 c3 48 8b 0d 1b cd 0c 00 f7 d8 64 89 01 48
RSP: 002b:00007ffcf220b2c8 EFLAGS: 00000246 ORIG_RAX: 0000000000000139
RAX: ffffffffffffffda RBX: 000055fdd2916aa0 RCX: 00007feeb5cc20cd
RDX: 0000000000000000 RSI: 000055fdd29161e0 RDI: 0000000000000035
RBP: 00007ffcf220b380 R08: 00007feeb5d8fb20 R09: 00007ffcf220b310
R10: 000055fdd2909dc0 R11: 0000000000000246 R12: 000055fdd29161e0
R13: 0000000000020000 R14: 000055fdd29203e0 R15: 000055fdd2909d80
</TASK>
We hit this when trying to initialize firmware of type
NVKM_FIRMWARE_IMG_DMA because we allocate our memory with
dma_alloc_coherent, and DMA allocations can't be turned back into memory
pages - which a scatterlist needs in order to map them.
So, fix this by allocating the memory with vmalloc instead().
V2:
* Fixup explanation as the prior one was bogus
Signed-off-by: Lyude Paul <[email protected]>
Reviewed-by: Dave Airlie <[email protected]>
Cc: [email protected]
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Avoid the implicit dev_priv local variable use, and pass dev_priv
explicitly to the PIPE_WGC_C22 register macro.
Reviewed-by: Rodrigo Vivi <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/0a07f615c574040094b37c861078e41daf53c706.1714399071.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <[email protected]>
|
|
Avoid the implicit dev_priv local variable use, and pass dev_priv
explicitly to the PIPE_WGC_C21_C20 register macro.
Reviewed-by: Rodrigo Vivi <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/af39047d304f8a5c3c7a643f702f66c06ea5d638.1714399071.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <[email protected]>
|
|
Avoid the implicit dev_priv local variable use, and pass dev_priv
explicitly to the PIPE_WGC_C12 register macro.
Reviewed-by: Rodrigo Vivi <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/62a748b685f253151b17c101dec75351577f30c0.1714399071.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <[email protected]>
|
|
Avoid the implicit dev_priv local variable use, and pass dev_priv
explicitly to the PIPE_WGC_C11_C10 register macro.
Reviewed-by: Rodrigo Vivi <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/3f7aae89cf63760bca43b54102c76b3ed2cf8735.1714399071.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <[email protected]>
|
|
Avoid the implicit dev_priv local variable use, and pass dev_priv
explicitly to the PIPE_WGC_C02 register macro.
Reviewed-by: Rodrigo Vivi <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/550d4e787445802236f0bf89e4d2f4f32cbd6d75.1714399071.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <[email protected]>
|
|
Avoid the implicit dev_priv local variable use, and pass dev_priv
explicitly to the PIPE_WGC_C01_C00 register macro.
Reviewed-by: Rodrigo Vivi <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/85b3db6e666a7a629b10b482b7e7043d52d30511.1714399071.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <[email protected]>
|
|
Avoid the implicit dev_priv local variable use, and pass dev_priv
explicitly to the PALETTE register macro.
Reviewed-by: Rodrigo Vivi <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/bf07d29cefef23ebd5d54fbb0d3bf7e41d132d93.1714399071.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <[email protected]>
|
|
https://gitlab.freedesktop.org/agd5f/linux into drm-next
amd-drm-next-6.10-2024-04-26:
amdgpu:
- Misc code cleanups and refactors
- Support setting reset method at runtime
- Report OD status
- SMU 14.0.1 fixes
- SDMA 4.4.2 fixes
- VPE fixes
- MES fixes
- Update BO eviction priorities
- UMSCH fixes
- Reset fixes
- Freesync fixes
- GFXIP 9.4.3 fixes
- SDMA 5.2 fixes
- MES UAF fix
- RAS updates
- Devcoredump updates for dumping IP state
- DSC fixes
- JPEG fix
- Fix VRAM memory accounting
- VCN 5.0 fixes
- MES fixes
- UMC 12.0 updates
- Modify contiguous flags handling
- Initial support for mapping kernel queues via MES
amdkfd:
- Fix rescheduling of restore worker
- VRAM accounting for SVM migrations
- mGPU fix
- Enable SQ watchpoint for gfx10
Signed-off-by: Dave Airlie <[email protected]>
From: Alex Deucher <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|