aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2018-08-31Merge tag 'arm64-fixes' of ↵Linus Torvalds3-17/+26
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux Pull arm64 fixes from Will Deacon: "A few arm64 fixes came in this week, specifically fixing some nasty truncation of return values from firmware calls and resolving a VM_BUG_ON due to accessing uninitialised struct pages corresponding to NOMAP pages. Summary: - Fix typos in SVE documentation - Fix type-checking and implicit truncation for SMCCC calls - Force CONFIG_HOLES_IN_ZONE=y so that SLAB doesn't fall over NOMAP regions" * tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: arm64: mm: always enable CONFIG_HOLES_IN_ZONE arm/arm64: smccc-1.1: Handle function result as parameters arm/arm64: smccc-1.1: Make return values unsigned long Documentation/arm64/sve: Couple of improvements and typos
2018-08-31x86/efi: Load fixmap GDT in efi_call_phys_epilog()Joerg Roedel1-6/+2
When PTI is enabled on x86-32 the kernel uses the GDT mapped in the fixmap for the simple reason that this address is also mapped for user-space. The efi_call_phys_prolog()/efi_call_phys_epilog() wrappers change the GDT to call EFI runtime services and switch back to the kernel GDT when they return. But the switch-back uses the writable GDT, not the fixmap GDT. When that happened and and the CPU returns to user-space it switches to the user %cr3 and tries to restore user segment registers. This fails because the writable GDT is not mapped in the user page-table, and without a GDT the fault handlers also can't be launched. The result is a triple fault and reboot of the machine. Fix that by restoring the GDT back to the fixmap GDT which is also mapped in the user page-table. Fixes: 7757d607c6b3 x86/pti: ('Allow CONFIG_PAGE_TABLE_ISOLATION for x86_32') Reported-by: Guenter Roeck <[email protected]> Signed-off-by: Joerg Roedel <[email protected]> Signed-off-by: Thomas Gleixner <[email protected]> Tested-by: Guenter Roeck <[email protected]> Cc: Ard Biesheuvel <[email protected]> Cc: Michal Hocko <[email protected]> Cc: Andi Kleen <[email protected]> Cc: Linus Torvalds <[email protected]> Cc: Dave Hansen <[email protected]> Cc: Pavel Machek <[email protected]> Cc: [email protected] Cc: [email protected] Link: https://lkml.kernel.org/r/[email protected]
2018-08-31Merge tag 'for-linus-4.19b-rc2-tag' of ↵Linus Torvalds4-10/+24
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip Pull xen fixes from Juergen Gross: - minor cleanup avoiding a warning when building with new gcc - a patch to add a new sysfs node for Xen frontend/backend drivers to make it easier to obtain the state of a pv device - two fixes for 32-bit pv-guests to avoid intermediate L1TF vulnerable PTEs * tag 'for-linus-4.19b-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: x86/xen: remove redundant variable save_pud xen: export device state to sysfs x86/pae: use 64 bit atomic xchg function in native_ptep_get_and_clear x86/xen: don't write ptes directly in 32-bit PV guests
2018-08-31Merge tag 'm68k-for-v4.19-tag2' of ↵Linus Torvalds1-6/+4
git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k Pull m68k fix from Geert Uytterhoeven: "Just a single fix for a bug introduced during the merge window: fix wrong date and time on PMU-based Macs" * tag 'm68k-for-v4.19-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k: m68k/mac: Use correct PMU response format
2018-08-31Merge branch 'i2c/for-current' of ↵Linus Torvalds8-44/+66
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux Pull i2c fixes from Wolfram Sang: - regression fixes for i801 and designware - better API and leak fix for releasing DMA safe buffers - better greppable strings for the bitbang algorithm * 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: i2c: sh_mobile: fix leak when using DMA bounce buffer i2c: sh_mobile: define start_ch() void as it only returns 0 anyhow i2c: refactor function to release a DMA safe buffer i2c: algos: bit: make the error messages grepable i2c: designware: Re-init controllers with pm_disabled set on resume i2c: i801: Allow ACPI AML access I/O ports not reserved for SMBus
2018-08-31x86/nmi: Fix NMI uaccess race against CR3 switchingAndy Lutomirski4-1/+53
A NMI can hit in the middle of context switching or in the middle of switch_mm_irqs_off(). In either case, CR3 might not match current->mm, which could cause copy_from_user_nmi() and friends to read the wrong memory. Fix it by adding a new nmi_uaccess_okay() helper and checking it in copy_from_user_nmi() and in __copy_from_user_nmi()'s callers. Signed-off-by: Andy Lutomirski <[email protected]> Signed-off-by: Thomas Gleixner <[email protected]> Reviewed-by: Rik van Riel <[email protected]> Cc: Nadav Amit <[email protected]> Cc: Borislav Petkov <[email protected]> Cc: Jann Horn <[email protected]> Cc: Peter Zijlstra <[email protected]> Cc: [email protected] Link: https://lkml.kernel.org/r/dd956eba16646fd0b15c3c0741269dfd84452dac.1535557289.git.luto@kernel.org
2018-08-31x86: Allow generating user-space headers without a compilerBen Hutchings1-4/+7
When bootstrapping an architecture, it's usual to generate the kernel's user-space headers (make headers_install) before building a compiler. Move the compiler check (for asm goto support) to the archprepare target so that it is only done when building code for the target. Fixes: e501ce957a78 ("x86: Force asm-goto") Reported-by: Helmut Grohne <[email protected]> Signed-off-by: Ben Hutchings <[email protected]> Signed-off-by: Thomas Gleixner <[email protected]> Cc: [email protected] Link: https://lkml.kernel.org/r/[email protected]
2018-08-31x86/dumpstack: Don't dump kernel memory based on usermode RIPJann Horn3-5/+15
show_opcodes() is used both for dumping kernel instructions and for dumping user instructions. If userspace causes #PF by jumping to a kernel address, show_opcodes() can be reached with regs->ip controlled by the user, pointing to kernel code. Make sure that userspace can't trick us into dumping kernel memory into dmesg. Fixes: 7cccf0725cf7 ("x86/dumpstack: Add a show_ip() function") Signed-off-by: Jann Horn <[email protected]> Signed-off-by: Thomas Gleixner <[email protected]> Reviewed-by: Kees Cook <[email protected]> Reviewed-by: Borislav Petkov <[email protected]> Cc: "H. Peter Anvin" <[email protected]> Cc: Andy Lutomirski <[email protected]> Cc: [email protected] Cc: [email protected] Link: https://lkml.kernel.org/r/[email protected]
2018-08-31ipmi: Fix I2C client removal in the SSIF driverCorey Minyard1-11/+6
The SSIF driver was removing any client that came in through the platform interface, but it should only remove clients that it added. On a failure in the probe function, this could result in the following oops when the driver is removed and the client gets unregistered twice: CPU: 107 PID: 30266 Comm: rmmod Not tainted 4.18.0+ #80 Hardware name: Cavium Inc. Saber/Saber, BIOS Cavium reference firmware version 7.0 08/04/2018 pstate: 60400009 (nZCv daif +PAN -UAO) pc : kernfs_find_ns+0x28/0x120 lr : kernfs_find_and_get_ns+0x40/0x60 sp : ffff00002310fb50 x29: ffff00002310fb50 x28: ffff800a8240f800 x27: 0000000000000000 x26: 0000000000000000 x25: 0000000056000000 x24: ffff000009073000 x23: ffff000008998b38 x22: 0000000000000000 x21: ffff800ed86de820 x20: 0000000000000000 x19: ffff00000913a1d8 x18: 0000000000000000 x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000 x14: 5300737265766972 x13: 643d4d4554535953 x12: 0000000000000030 x11: 0000000000000030 x10: 0101010101010101 x9 : ffff800ea06cc3f9 x8 : 0000000000000000 x7 : 0000000000000141 x6 : ffff000009073000 x5 : ffff800adb706b00 x4 : 0000000000000000 x3 : 00000000ffffffff x2 : 0000000000000000 x1 : ffff000008998b38 x0 : ffff000008356760 Process rmmod (pid: 30266, stack limit = 0x00000000e218418d) Call trace: kernfs_find_ns+0x28/0x120 kernfs_find_and_get_ns+0x40/0x60 sysfs_unmerge_group+0x2c/0x6c dpm_sysfs_remove+0x34/0x70 device_del+0x58/0x30c device_unregister+0x30/0x7c i2c_unregister_device+0x84/0x90 [i2c_core] ssif_platform_remove+0x38/0x98 [ipmi_ssif] platform_drv_remove+0x2c/0x6c device_release_driver_internal+0x168/0x1f8 driver_detach+0x50/0xbc bus_remove_driver+0x74/0xe8 driver_unregister+0x34/0x5c platform_driver_unregister+0x20/0x2c cleanup_ipmi_ssif+0x50/0xd82c [ipmi_ssif] __arm64_sys_delete_module+0x1b4/0x220 el0_svc_handler+0x104/0x160 el0_svc+0x8/0xc Code: aa1e03e0 aa0203f6 aa0103f7 d503201f (7940e280) ---[ end trace 09f0e34cce8e2d8c ]--- Kernel panic - not syncing: Fatal exception SMP: stopping secondary CPUs Kernel Offset: disabled CPU features: 0x23800c38 So track the clients that the SSIF driver adds and only remove those. Reported-by: George Cherian <[email protected]> Signed-off-by: Corey Minyard <[email protected]> Tested-by: George Cherian <[email protected]> Cc: <[email protected]> # 4.14.x
2018-08-31ipmi: Move BT capabilities detection to the detect callCorey Minyard1-44/+48
The capabilities detection was being done as part of the normal state machine, but it was possible for it to be running while the upper layers of the IPMI driver were initializing the device, resulting in error and failure to initialize. Move the capabilities detection to the the detect function, so it's done before anything else runs on the device. This also simplifies the state machine and removes some code, as a bonus. Signed-off-by: Corey Minyard <[email protected]> Reported-by: Andrew Banman <[email protected]> Tested-by: Andrew Banman <[email protected]> Cc: <[email protected]>
2018-08-31ipmi: Rework SMI registration failureCorey Minyard3-46/+37
There were certain situations where ipmi_register_smi() would return a failure, but the interface would still be registered and would need to be unregistered. This is obviously a bad design and resulted in an oops in certain failure cases. If the interface is started up in ipmi_register_smi(), then an error occurs, shut down the interface there so the cleanup can be done properly. Fix the various smi users, too. Signed-off-by: Corey Minyard <[email protected]> Reported-by: Justin Ernst <[email protected]> Tested-by: Justin Ernst <[email protected]> Cc: Andrew Banman <[email protected]> Cc: Russ Anderson <[email protected]> Cc: <[email protected]> # 4.18.x
2018-08-31of: Add device_type access helper functionsRob Herring1-0/+12
In preparation to remove direct access to device_node.type, add of_node_is_type() and of_node_get_device_type() helpers to check and retrieve the device type. Cc: Frank Rowand <[email protected]> Signed-off-by: Rob Herring <[email protected]>
2018-08-31cpu/hotplug: Remove skip_onerr field from cpuhp_step structureMukesh Ojha1-22/+4
When notifiers were there, `skip_onerr` was used to avoid calling particular step startup/teardown callbacks in the CPU up/down rollback path, which made the hotplug asymmetric. As notifiers are gone now after the full state machine conversion, the `skip_onerr` field is no longer required. Remove it from the structure and its usage. Signed-off-by: Mukesh Ojha <[email protected]> Signed-off-by: Thomas Gleixner <[email protected]> Acked-by: Peter Zijlstra (Intel) <[email protected]> Link: https://lkml.kernel.org/r/[email protected]
2018-08-31arm64: mm: always enable CONFIG_HOLES_IN_ZONEJames Morse1-1/+0
Commit 6d526ee26ccd ("arm64: mm: enable CONFIG_HOLES_IN_ZONE for NUMA") only enabled HOLES_IN_ZONE for NUMA systems because the NUMA code was choking on the missing zone for nomap pages. This problem doesn't just apply to NUMA systems. If the architecture doesn't set HAVE_ARCH_PFN_VALID, pfn_valid() will return true if the pfn is part of a valid sparsemem section. When working with multiple pages, the mm code uses pfn_valid_within() to test each page it uses within the sparsemem section is valid. On most systems memory comes in MAX_ORDER_NR_PAGES chunks which all have valid/initialised struct pages. In this case pfn_valid_within() is optimised out. Systems where this isn't true (e.g. due to nomap) should set HOLES_IN_ZONE and provide HAVE_ARCH_PFN_VALID so that mm tests each page as it works with it. Currently non-NUMA arm64 systems can't enable HOLES_IN_ZONE, leading to a VM_BUG_ON(): | page:fffffdff802e1780 is uninitialized and poisoned | raw: ffffffffffffffff ffffffffffffffff ffffffffffffffff ffffffffffffffff | raw: ffffffffffffffff ffffffffffffffff ffffffffffffffff ffffffffffffffff | page dumped because: VM_BUG_ON_PAGE(PagePoisoned(p)) | ------------[ cut here ]------------ | kernel BUG at include/linux/mm.h:978! | Internal error: Oops - BUG: 0 [#1] PREEMPT SMP [...] | CPU: 1 PID: 25236 Comm: dd Not tainted 4.18.0 #7 | Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015 | pstate: 40000085 (nZcv daIf -PAN -UAO) | pc : move_freepages_block+0x144/0x248 | lr : move_freepages_block+0x144/0x248 | sp : fffffe0071177680 [...] | Process dd (pid: 25236, stack limit = 0x0000000094cc07fb) | Call trace: | move_freepages_block+0x144/0x248 | steal_suitable_fallback+0x100/0x16c | get_page_from_freelist+0x440/0xb20 | __alloc_pages_nodemask+0xe8/0x838 | new_slab+0xd4/0x418 | ___slab_alloc.constprop.27+0x380/0x4a8 | __slab_alloc.isra.21.constprop.26+0x24/0x34 | kmem_cache_alloc+0xa8/0x180 | alloc_buffer_head+0x1c/0x90 | alloc_page_buffers+0x68/0xb0 | create_empty_buffers+0x20/0x1ec | create_page_buffers+0xb0/0xf0 | __block_write_begin_int+0xc4/0x564 | __block_write_begin+0x10/0x18 | block_write_begin+0x48/0xd0 | blkdev_write_begin+0x28/0x30 | generic_perform_write+0x98/0x16c | __generic_file_write_iter+0x138/0x168 | blkdev_write_iter+0x80/0xf0 | __vfs_write+0xe4/0x10c | vfs_write+0xb4/0x168 | ksys_write+0x44/0x88 | sys_write+0xc/0x14 | el0_svc_naked+0x30/0x34 | Code: aa1303e0 90001a01 91296421 94008902 (d4210000) | ---[ end trace 1601ba47f6e883fe ]--- Remove the NUMA dependency. Link: https://www.spinics.net/lists/arm-kernel/msg671851.html Cc: <[email protected]> Cc: Ard Biesheuvel <[email protected]> Reported-by: Mikulas Patocka <[email protected]> Reviewed-by: Pavel Tatashin <[email protected]> Tested-by: Mikulas Patocka <[email protected]> Signed-off-by: James Morse <[email protected]> Signed-off-by: Will Deacon <[email protected]>
2018-08-31gpio: Fix crash due to registration raceVincent Whitchurch1-0/+1
gpiochip_add_data_with_key() adds the gpiochip to the gpio_devices list before of_gpiochip_add() is called, but it's only the latter which sets the ->of_xlate function pointer. gpiochip_find() can be called by someone else between these two actions, and it can find the chip and call of_gpiochip_match_node_and_xlate() which leads to the following crash due to a NULL ->of_xlate(). Unhandled prefetch abort: page domain fault (0x01b) at 0x00000000 Modules linked in: leds_gpio(+) gpio_generic(+) CPU: 0 PID: 830 Comm: insmod Not tainted 4.18.0+ #43 Hardware name: ARM-Versatile Express PC is at (null) LR is at of_gpiochip_match_node_and_xlate+0x2c/0x38 Process insmod (pid: 830, stack limit = 0x(ptrval)) (of_gpiochip_match_node_and_xlate) from (gpiochip_find+0x48/0x84) (gpiochip_find) from (of_get_named_gpiod_flags+0xa8/0x238) (of_get_named_gpiod_flags) from (gpiod_get_from_of_node+0x2c/0xc8) (gpiod_get_from_of_node) from (devm_fwnode_get_index_gpiod_from_child+0xb8/0x144) (devm_fwnode_get_index_gpiod_from_child) from (gpio_led_probe+0x208/0x3c4 [leds_gpio]) (gpio_led_probe [leds_gpio]) from (platform_drv_probe+0x48/0x9c) (platform_drv_probe) from (really_probe+0x1d0/0x3d4) (really_probe) from (driver_probe_device+0x78/0x1c0) (driver_probe_device) from (__driver_attach+0x120/0x13c) (__driver_attach) from (bus_for_each_dev+0x68/0xb4) (bus_for_each_dev) from (bus_add_driver+0x1a8/0x268) (bus_add_driver) from (driver_register+0x78/0x10c) (driver_register) from (do_one_initcall+0x54/0x1fc) (do_one_initcall) from (do_init_module+0x64/0x1f4) (do_init_module) from (load_module+0x2198/0x26ac) (load_module) from (sys_finit_module+0xe0/0x110) (sys_finit_module) from (ret_fast_syscall+0x0/0x54) One way to fix this would be to rework the hairy registration sequence in gpiochip_add_data_with_key(), but since I'd probably introduce a couple of new bugs if I attempted that, simply add a check for a non-NULL of_xlate function pointer in of_gpiochip_match_node_and_xlate(). This works since the driver looking for the gpio will simply fail to find the gpio and defer its probe and be reprobed when the driver which is registering the gpiochip has fully completed its probe. Signed-off-by: Vincent Whitchurch <[email protected]> Signed-off-by: Linus Walleij <[email protected]>
2018-08-31m68k/mac: Use correct PMU response formatFinn Thain1-6/+4
Now that the 68k Mac port has adopted the via-pmu driver, it must decode the PMU response accordingly otherwise the date and time will be wrong. Fixes: ebd722275f9cfc67 ("macintosh/via-pmu: Replace via-pmu68k driver with via-pmu driver") Signed-off-by: Finn Thain <[email protected]> Signed-off-by: Geert Uytterhoeven <[email protected]>
2018-08-30Merge tag 'drm-fixes-2018-08-31' of git://anongit.freedesktop.org/drm/drmLinus Torvalds26-161/+303
Pull drm fixes from Dave Airlie: "Regular fixes pull: - Mediatek has a bunch of fixes to their RDMA and Overlay engines. - i915 has some Cannonlake/Geminilake watermark workarounds, LSPCON fix, HDCP free fix, audio fix and a ppgtt reference counting fix. - amdgpu has some SRIOV, Kasan, memory leaks and other misc fixes" * tag 'drm-fixes-2018-08-31' of git://anongit.freedesktop.org/drm/drm: (35 commits) drm/i915/audio: Hook up component bindings even if displays are disabled drm/i915: Increase LSPCON timeout drm/i915: Stop holding a ref to the ppgtt from each vma drm/i915: Free write_buf that we allocated with kzalloc. drm/i915: Fix glk/cnl display w/a #1175 drm/amdgpu: Need to set moved to true when evict bo drm/amdgpu: Remove duplicated power source update drm/amd/display: Fix memory leak caused by missed dc_sink_release drm/amdgpu: fix holding mn_lock while allocating memory drm/amdgpu: Power on uvd block when hw_fini drm/amdgpu: Update power state at the end of smu hw_init. drm/amdgpu: Fix vce initialize failed on Kaveri/Mullins drm/amdgpu: Enable/disable gfx PG feature in rlc safe mode drm/amdgpu: Adjust the VM size based on system memory size v2 drm/mediatek: fix connection from RDMA2 to DSI1 drm/mediatek: update some variable name from ovl to comp drm/mediatek: use layer_nr function to get layer number to init plane drm/mediatek: add function to return RDMA layer number drm/mediatek: add function to return OVL layer number drm/mediatek: add function to get layer number for component ...
2018-08-30disable stringop truncation warnings for nowStephen Rothwell1-0/+3
They are too noisy Signed-off-by: Stephen Rothwell <[email protected]> Signed-off-by: Linus Torvalds <[email protected]>
2018-08-30Merge tag 'pm-4.19-rc2' of ↵Linus Torvalds2-2/+13
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm Pull power management fixes from Rafael Wysocki: "These address a corner case in the menu cpuidle governor and fix error handling in the PM core's generic clock management code. Specifics: - Make the menu cpuidle governor avoid stopping the scheduler tick if the predicted idle duration exceeds the tick period length, but the selected idle state is shallow and deeper idle states with high target residencies are available (Rafael Wysocki). - Make the PM core's generic clock management code use a proper data type for one variable to make error handling work (Dan Carpenter)" * tag 'pm-4.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: cpuidle: menu: Retain tick when shallow state is selected PM / clk: signedness bug in of_pm_clk_add_clks()
2018-08-30arc: remove redundant GCC version checksMasahiro Yamada1-9/+1
Commit cafa0010cd51 ("Raise the minimum required gcc version to 4.6") bumped the minimum GCC version to 4.6 for all architectures. With GCC >= 4.6 assumed, 'upto_gcc44' is empty, 'atleast_gcc44' is y. Signed-off-by: Masahiro Yamada <[email protected]> Signed-off-by: Vineet Gupta <[email protected]>
2018-08-31Merge branch 'pm-core'Rafael J. Wysocki1-1/+1
Merge a generic clock management fix for 4.19-rc2. * pm-core: PM / clk: signedness bug in of_pm_clk_add_clks()
2018-08-30clk: x86: Set default parent to 48MhzAkshu Agrawal1-1/+1
System clk provided in ST soc can be set to: 48Mhz, non-spread 25Mhz, spread To get accurate rate, we need it to set it at non-spread option which is 48Mhz. Signed-off-by: Akshu Agrawal <[email protected]> Reviewed-by: Daniel Kurtz <[email protected]> Fixes: 421bf6a1f061 ("clk: x86: Add ST oscout platform clock") Signed-off-by: Stephen Boyd <[email protected]>
2018-08-30i2c: sh_mobile: fix leak when using DMA bounce bufferWolfram Sang1-2/+4
We only freed the bounce buffer after successful DMA, missing the cases where DMA setup may have gone wrong. Use a better location which always gets called after each message and use 'stop_after_dma' as a flag for a successful transfer. Signed-off-by: Wolfram Sang <[email protected]> Reviewed-by: Niklas Söderlund <[email protected]> Signed-off-by: Wolfram Sang <[email protected]>
2018-08-30i2c: sh_mobile: define start_ch() void as it only returns 0 anyhowWolfram Sang1-6/+3
After various refactoring over the years, start_ch() doesn't return errno anymore, so make the function return void. This saves the error handling when calling it which in turn eases cleanup of resources of a future patch. Signed-off-by: Wolfram Sang <[email protected]> Reviewed-by: Niklas Söderlund <[email protected]> Signed-off-by: Wolfram Sang <[email protected]>
2018-08-30i2c: refactor function to release a DMA safe bufferWolfram Sang4-10/+15
a) rename to 'put' instead of 'release' to match 'get' when obtaining the buffer b) change the argument order to have the buffer as first argument c) add a new argument telling the function if the message was transferred. This allows the function to be used also in cases where setting up DMA failed, so the buffer needs to be freed without syncing to the message buffer. Also convert the only user. Signed-off-by: Wolfram Sang <[email protected]> Reviewed-by: Niklas Söderlund <[email protected]> Signed-off-by: Wolfram Sang <[email protected]>
2018-08-30i2c: algos: bit: make the error messages grepableJan Kundrát1-24/+31
Yep, I went looking for one of these, and I wasn't able to find it easily. That's worse than a line which is 82-chars long, IMHO. Signed-off-by: Jan Kundrát <[email protected]> Signed-off-by: Wolfram Sang <[email protected]>
2018-08-30i2c: designware: Re-init controllers with pm_disabled set on resumeHans de Goede2-2/+6
On Bay Trail and Cherry Trail devices we set the pm_disabled flag for I2C busses which the OS shares with the PUNIT as these need special handling. Until now we called dev_pm_syscore_device(dev, true) for I2C controllers with this flag set to keep these I2C controllers always on. After commit 12864ff8545f ("ACPI / LPSS: Avoid PM quirks on suspend and resume from hibernation"), this no longer works. This commit modifies lpss_iosf_exit_d3_state() to only run if lpss_iosf_enter_d3_state() has ran before it, so that it does not run on a resume from hibernate (or from S3). On these systems the conditions for lpss_iosf_enter_d3_state() to run never become true, so lpss_iosf_exit_d3_state() never gets called and the 2 LPSS DMA controllers never get forced into D0 mode, instead they are left in their default automatic power-on when needed mode. The not forcing of D0 mode for the DMA controllers enables these systems to properly enter S0ix modes, which is a good thing. But after entering S0ix modes the I2C controller connected to the PMIC no longer works, leading to e.g. broken battery monitoring. The _PS3 method for this I2C controller looks like this: Method (_PS3, 0, NotSerialized) // _PS3: Power State 3 { If ((((PMID == 0x04) || (PMID == 0x05)) || (PMID == 0x06))) { Return (Zero) } PSAT |= 0x03 Local0 = PSAT /* \_SB_.I2C5.PSAT */ } Where PMID = 0x05, so we enter the Return (Zero) path on these systems. So even if we were to not call dev_pm_syscore_device(dev, true) the I2C controller will be left in D0 rather then be switched to D3. Yet on other Bay and Cherry Trail devices S0ix is not entered unless *all* I2C controllers are in D3 mode. This combined with the I2C controller no longer working now that we reach S0ix states on these systems leads to me believing that the PUNIT itself puts the I2C controller in D3 when all other conditions for entering S0ix states are true. Since now the I2C controller is put in D3 over a suspend/resume we must re-initialize it afterwards and that does indeed fix it no longer working. This commit implements this fix by: 1) Making the suspend_late callback a no-op if pm_disabled is set and making the resume_early callback skip the clock re-enable (since it now was not disabled) while still doing the necessary I2C controller re-init. 2) Removing the dev_pm_syscore_device(dev, true) call, so that the suspend and resume callbacks are actually called. Normally this would cause the ACPI pm code to call _PS3 putting the I2C controller in D3, wreaking havoc since it is shared with the PUNIT, but in this special case the _PS3 method is a no-op so we can safely allow a "fake" suspend / resume. Fixes: 12864ff8545f ("ACPI / LPSS: Avoid PM quirks on suspend and resume ...") Link: https://bugzilla.kernel.org/show_bug.cgi?id=200861 Cc: 4.15+ <[email protected]> # 4.15+ Signed-off-by: Hans de Goede <[email protected]> Reviewed-by: Andy Shevchenko <[email protected]> Acked-by: Jarkko Nikula <[email protected]> Signed-off-by: Wolfram Sang <[email protected]>
2018-08-30i2c: i801: Allow ACPI AML access I/O ports not reserved for SMBusMika Westerberg1-1/+8
Commit 7ae81952cda ("i2c: i801: Allow ACPI SystemIO OpRegion to conflict with PCI BAR") made it possible for AML code to access SMBus I/O ports by installing custom SystemIO OpRegion handler and blocking i80i driver access upon first AML read/write to this OpRegion. However, while ThinkPad T560 does have SystemIO OpRegion declared under the SMBus device, it does not access any of the SMBus registers: Device (SMBU) { ... OperationRegion (SMBP, PCI_Config, 0x50, 0x04) Field (SMBP, DWordAcc, NoLock, Preserve) { , 5, TCOB, 11, Offset (0x04) } Name (TCBV, 0x00) Method (TCBS, 0, NotSerialized) { If ((TCBV == 0x00)) { TCBV = (\_SB.PCI0.SMBU.TCOB << 0x05) } Return (TCBV) /* \_SB_.PCI0.SMBU.TCBV */ } OperationRegion (TCBA, SystemIO, TCBS (), 0x10) Field (TCBA, ByteAcc, NoLock, Preserve) { Offset (0x04), , 9, CPSC, 1 } } Problem with the current approach is that it blocks all I/O port access and because this system has touchpad connected to the SMBus controller after first AML access (happens during suspend/resume cycle) the touchpad fails to work anymore. Fix this so that we allow ACPI AML I/O port access if it does not touch the region reserved for the SMBus. Fixes: 7ae81952cda ("i2c: i801: Allow ACPI SystemIO OpRegion to conflict with PCI BAR") Link: https://bugzilla.kernel.org/show_bug.cgi?id=200737 Reported-by: Yussuf Khalil <[email protected]> Signed-off-by: Mika Westerberg <[email protected]> Reviewed-by: Jean Delvare <[email protected]> Signed-off-by: Wolfram Sang <[email protected]>
2018-08-30Merge tag 'for-linus-20180830' of git://git.kernel.dk/linux-blockLinus Torvalds12-108/+269
Pull block fixes from Jens Axboe: "Small collection of fixes that should go into this series. This pull contains: - NVMe pull request with three small fixes (via Christoph) - Kill useless NULL check before kmem_cache_destroy (Chengguang Xu) - Xen block driver pull request with persistent grant flushing fixes (Juergen Gross) - Final wbt fixes, wrapping up the changes for this series. These have been heavily tested (me) - cdrom info leak fix (Scott Bauer) - ATA dma quirk for SQ201 (Linus Walleij) - Straight forward bsg refcount_t conversion (John Pittman)" * tag 'for-linus-20180830' of git://git.kernel.dk/linux-block: cdrom: Fix info leak/OOB read in cdrom_ioctl_drive_status nvmet: free workqueue object if module init fails nvme-fcloop: Fix dropped LS's to removed target port nvme-pci: add a memory barrier to nvme_dbbuf_update_and_check_event block: bsg: move atomic_t ref_count variable to refcount API block: remove unnecessary condition check ata: ftide010: Add a quirk for SQ201 blk-wbt: remove dead code blk-wbt: improve waking of tasks blk-wbt: abstract out end IO completion handler xen/blkback: remove unused pers_gnts_lock from struct xen_blkif_ring xen/blkback: move persistent grants flags to bool xen/blkfront: reorder tests in xlblk_init() xen/blkfront: cleanup stale persistent grants xen/blkback: don't keep persistent grants too long
2018-08-30ipmi: kcs_bmc: don't change device nameBenjamin Fair1-3/+4
kcs_bmc_alloc(...) calls dev_set_name(...) which is incorrect as most bus driver frameworks, platform_driver in particular, assume that they are able to set the device name themselves. Signed-off-by: Benjamin Fair <[email protected]> Signed-off-by: Corey Minyard <[email protected]>
2018-08-30of: add node name compare helper functionsRob Herring2-0/+35
In preparation to remove device_node.name pointer, add helper functions for node name comparisons which are a common pattern throughout the kernel. Cc: Frank Rowand <[email protected]> Signed-off-by: Rob Herring <[email protected]>
2018-08-30perf annotate: Fix parsing aarch64 branch instructions after objdump updateKim Phillips2-1/+22
Starting with binutils 2.28, aarch64 objdump adds comments to the disassembly output to show the alternative names of a condition code [1]. It is assumed that commas in objdump comments could occur in other arches now or in the future, so this fix is arch-independent. The fix could have been done with arm64 specific jump__parse and jump__scnprintf functions, but the jump__scnprintf instruction would have to have its comment character be a literal, since the scnprintf functions cannot receive a struct arch easily. This inconvenience also applies to the generic jump__scnprintf, which is why we add a raw_comment pointer to struct ins_operands, so the __parse function assigns it to be re-used by its corresponding __scnprintf function. Example differences in 'perf annotate --stdio2' output on an aarch64 perf.data file: BEFORE: → b.cs ffff200008133d1c <unwind_frame+0x18c> // b.hs, dffff7ecc47b AFTER : ↓ b.cs 18c BEFORE: → b.cc ffff200008d8d9cc <get_alloc_profile+0x31c> // b.lo, b.ul, dffff727295b AFTER : ↓ b.cc 31c The branch target labels 18c and 31c also now appear in the output: BEFORE: add x26, x29, #0x80 AFTER : 18c: add x26, x29, #0x80 BEFORE: add x21, x21, #0x8 AFTER : 31c: add x21, x21, #0x8 The Fixes: tag below is added so stable branches will get the update; it doesn't necessarily mean that commit was broken at the time, rather it didn't withstand the aarch64 objdump update. Tested no difference in output for sample x86_64, power arch perf.data files. [1] https://sourceware.org/git/gitweb.cgi?p=binutils-gdb.git;a=commit;h=bb7eff5206e4795ac79c177a80fe9f4630aaf730 Signed-off-by: Kim Phillips <[email protected]> Tested-by: Arnaldo Carvalho de Melo <[email protected]> Cc: Alexander Shishkin <[email protected]> Cc: Anton Blanchard <[email protected]> Cc: Christian Borntraeger <[email protected]> Cc: Jiri Olsa <[email protected]> Cc: Mark Rutland <[email protected]> Cc: Namhyung Kim <[email protected]> Cc: Peter Zijlstra <[email protected]> Cc: Ravi Bangoria <[email protected]> Cc: Robin Murphy <[email protected]> Cc: Taeung Song <[email protected]> Cc: [email protected] Fixes: b13bbeee5ee6 ("perf annotate: Fix branch instruction with multiple operands") Link: http://lkml.kernel.org/r/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
2018-08-30perf probe powerpc: Ignore SyS symbols irrespective of endiannessSandipan Das1-1/+3
This makes sure that the SyS symbols are ignored for any powerpc system, not just the big endian ones. Reported-by: Naveen N. Rao <[email protected]> Signed-off-by: Sandipan Das <[email protected]> Reviewed-by: Kamalesh Babulal <[email protected]> Acked-by: Naveen N. Rao <[email protected]> Cc: Jiri Olsa <[email protected]> Cc: Ravi Bangoria <[email protected]> Fixes: fb6d59423115 ("perf probe ppc: Use the right prefix when ignoring SyS symbols on ppc") Link: http://lkml.kernel.org/r/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
2018-08-30vfs: implement readahead(2) using POSIX_FADV_WILLNEEDAmir Goldstein3-30/+21
The implementation of readahead(2) syscall is identical to that of fadvise64(POSIX_FADV_WILLNEED) with a few exceptions: 1. readahead(2) returns -EINVAL for !mapping->a_ops and fadvise64() ignores the request and returns 0. 2. fadvise64() checks for integer overflow corner case 3. fadvise64() calls the optional filesystem fadvise() file operation Unite the two implementations by calling vfs_fadvise() from readahead(2) syscall. Check the !mapping->a_ops in readahead(2) syscall to preserve documented syscall ABI behaviour. Suggested-by: Miklos Szeredi <[email protected]> Fixes: d1d04ef8572b ("ovl: stack file ops") Signed-off-by: Amir Goldstein <[email protected]> Signed-off-by: Miklos Szeredi <[email protected]>
2018-08-30perf event-parse: Use fixed size string for commsChris Phlipot1-4/+3
Some implementations of libc do not support the 'm' width modifier as part of the scanf string format specifier. This can cause the parsing to fail. Since the parser never checks if the scanf parsing was successesful, this can result in a crash. Change the comm string to be allocated as a fixed size instead of dynamically using 'm' scanf width modifier. This can be safely done since comm size is limited to 16 bytes by TASK_COMM_LEN within the kernel. This change prevents perf from crashing when linked against bionic as well as reduces the total number of heap allocations and frees invoked while accomplishing the same task. Signed-off-by: Chris Phlipot <[email protected]> Cc: Namhyung Kim <[email protected]> Cc: Peter Zijlstra <[email protected]> Link: http://lkml.kernel.org/r/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
2018-08-30perf util: Fix bad memory access in trace info.Chris Phlipot1-1/+1
In the write to the output_fd in the error condition of record_saved_cmdline(), we are writing 8 bytes from a memory location on the stack that contains a primitive that is only 4 bytes in size. Change the primitive to 8 bytes in size to match the size of the write in order to avoid reading unknown memory from the stack. Signed-off-by: Chris Phlipot <[email protected]> Cc: Namhyung Kim <[email protected]> Cc: Peter Zijlstra <[email protected]> Link: http://lkml.kernel.org/r/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
2018-08-30perf tools: Streamline bpf examples and headers installationArnaldo Carvalho de Melo1-8/+6
We were emitting 4 lines, two of them misleading: make: Entering directory '/home/acme/git/perf/tools/perf' <SNIP> INSTALL lib INSTALL include/bpf INSTALL lib INSTALL examples/bpf <SNIP> make: Leaving directory '/home/acme/git/perf/tools/perf' Make it more compact by showing just two lines: make: Entering directory '/home/acme/git/perf/tools/perf' INSTALL bpf-headers INSTALL bpf-examples make: Leaving directory '/home/acme/git/perf/tools/perf' Cc: Adrian Hunter <[email protected]> Cc: David Ahern <[email protected]> Cc: Jiri Olsa <[email protected]> Cc: Namhyung Kim <[email protected]> Cc: Wang Nan <[email protected]> Link: https://lkml.kernel.org/n/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
2018-08-30perf evsel: Fix potential null pointer dereference in perf_evsel__new_idx()Hisao Tanabe1-2/+3
If evsel is NULL, we should return NULL to avoid a NULL pointer dereference a bit later in the code. Signed-off-by: Hisao Tanabe <[email protected]> Acked-by: Namhyung Kim <[email protected]> Cc: Jiri Olsa <[email protected]> Cc: Wang Nan <[email protected]> Fixes: 03e0a7df3efd ("perf tools: Introduce bpf-output event") LPU-Reference: [email protected] Link: https://lkml.kernel.org/n/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
2018-08-30perf arm64: Fix include path for asm-generic/unistd.hKim Phillips2-5/+6
The new syscall table support for arm64 mistakenly used the system's asm-generic/unistd.h file when processing the tools/arch/arm64/include/uapi/asm/unistd.h file's include directive: #include <asm-generic/unistd.h> See "Committer notes" section of commit 2b5882435606 "perf arm64: Generate system call table from asm/unistd.h" for more details. This patch removes the committer's temporary workaround, and instructs the host compiler to search the build tree's include path for the right copy of the unistd.h file, instead of the one on the system's /usr/include path. It thus fixes the committer's test that cross-builds an arm64 perf on an x86 platform running Ubuntu 14.04.5 LTS with an old toolchain: $ tools/perf/arch/arm64/entry/syscalls/mksyscalltbl /gcc-linaro-5.4.1-2017.05-x86_64_aarch64-linux-gnu/bin/aarch64-linux-gnu-gcc gcc `pwd`/tools tools/arch/arm64/include/uapi/asm/unistd.h | grep bpf [280] = "bpf", Signed-off-by: Kim Phillips <[email protected]> Cc: Alexander Shishkin <[email protected]> Cc: Hendrik Brueckner <[email protected]> Cc: Jiri Olsa <[email protected]> Cc: Michael Ellerman <[email protected]> Cc: Namhyung Kim <[email protected]> Cc: Peter Zijlstra <[email protected]> Cc: Ravi Bangoria <[email protected]> Cc: Thomas Richter <[email protected]> Fixes: 2b5882435606 ("perf arm64: Generate system call table from asm/unistd.h") Link: http://lkml.kernel.org/r/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
2018-08-30perf/hw_breakpoint: Simplify breakpoint enable in perf_event_modify_breakpointJiri Olsa1-8/+3
We can safely enable the breakpoint back for both the fail and success paths by checking only the bp->attr.disabled, which either holds the new 'requested' disabled state or the original breakpoint state. Committer testing: At the end of the series, the 'perf test' entry introduced as the first patch now runs to completion without finding the fixed issues: # perf test "bp modify" 62: x86 bp modify : Ok # In verbose mode: # perf test -v "bp modify" 62: x86 bp modify : --- start --- test child forked, pid 5161 rip 5950a0, bp_1 0x5950a0 in bp_1 rip 5950a0, bp_1 0x5950a0 in bp_1 test child finished with 0 ---- end ---- x86 bp modify: Ok Suggested-by: Oleg Nesterov <[email protected]> Acked-by: Oleg Nesterov <[email protected]> Signed-off-by: Jiri Olsa <[email protected]> Tested-by: Arnaldo Carvalho de Melo <[email protected]> Cc: Alexander Shishkin <[email protected]> Cc: David Ahern <[email protected]> Cc: Milind Chabbi <[email protected]> Cc: Namhyung Kim <[email protected]> Cc: Peter Zijlstra <[email protected]> Link: http://lkml.kernel.org/r/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
2018-08-30perf/hw_breakpoint: Enable breakpoint in modify_user_hw_breakpointJiri Olsa1-4/+2
Currently we enable the breakpoint back only if the breakpoint modification was successful. If it fails we can leave the breakpoint in disabled state with attr->disabled == 0. We can safely enable the breakpoint back for both the fail and success paths by checking the bp->attr.disabled, which either holds the new 'requested' disabled state or the original breakpoint state. Suggested-by: Oleg Nesterov <[email protected]> Signed-off-by: Jiri Olsa <[email protected]> Acked-by: Frederic Weisbecker <[email protected]> Acked-by: Oleg Nesterov <[email protected]> Tested-by: Arnaldo Carvalho de Melo <[email protected]> Cc: Alexander Shishkin <[email protected]> Cc: David Ahern <[email protected]> Cc: Milind Chabbi <[email protected]> Cc: Namhyung Kim <[email protected]> Cc: Peter Zijlstra <[email protected]> Link: http://lkml.kernel.org/r/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
2018-08-30perf/hw_breakpoint: Remove superfluous bp->attr.disabled = 0Jiri Olsa1-3/+2
Once the breakpoint was succesfully modified, the attr->disabled value is in bp->attr.disabled. So there's no reason to set it again, removing that. Signed-off-by: Jiri Olsa <[email protected]> Acked-by: Frederic Weisbecker <[email protected]> Acked-by: Oleg Nesterov <[email protected]> Tested-by: Arnaldo Carvalho de Melo <[email protected]> Cc: Alexander Shishkin <[email protected]> Cc: David Ahern <[email protected]> Cc: Milind Chabbi <[email protected]> Cc: Namhyung Kim <[email protected]> Cc: Peter Zijlstra <[email protected]> Link: http://lkml.kernel.org/r/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
2018-08-30perf/hw_breakpoint: Modify breakpoint even if the new attr has disabled setJiri Olsa1-4/+6
We need to change the breakpoint even if the attr with new fields has disabled set to true. Current code prevents following user code to change the breakpoint address: ptrace(PTRACE_POKEUSER, child, offsetof(struct user, u_debugreg[0]), addr_1) ptrace(PTRACE_POKEUSER, child, offsetof(struct user, u_debugreg[0]), addr_2) ptrace(PTRACE_POKEUSER, child, offsetof(struct user, u_debugreg[7]), dr7) The first PTRACE_POKEUSER creates the breakpoint with attr.disabled set to true: ptrace_set_breakpoint_addr(nr = 0) struct perf_event *bp = t->ptrace_bps[nr]; ptrace_register_breakpoint(..., disabled = true) ptrace_fill_bp_fields(..., disabled) register_user_hw_breakpoint So the second PTRACE_POKEUSER will be omitted: ptrace_set_breakpoint_addr(nr = 0) struct perf_event *bp = t->ptrace_bps[nr]; struct perf_event_attr attr = bp->attr; modify_user_hw_breakpoint(bp, &attr) if (!attr->disabled) modify_user_hw_breakpoint_check Reported-by: Milind Chabbi <[email protected]> Signed-off-by: Jiri Olsa <[email protected]> Acked-by: Frederic Weisbecker <[email protected]> Acked-by: Oleg Nesterov <[email protected]> Tested-by: Arnaldo Carvalho de Melo <[email protected]> Cc: Alexander Shishkin <[email protected]> Cc: David Ahern <[email protected]> Cc: Namhyung Kim <[email protected]> Cc: Peter Zijlstra <[email protected]> Link: http://lkml.kernel.org/r/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
2018-08-30perf tests: Add breakpoint modify testsJiri Olsa4-0/+221
Adding to tests that aims on kernel breakpoint modification bugs. First test creates HW breakpoint, tries to change it and checks it was properly changed. It aims on kernel issue that prevents HW breakpoint to be changed via ptrace interface. The first test forks, the child sets itself as ptrace tracee and waits in signal for parent to trace it, then it calls bp_1 and quits. The parent does following steps: - creates a new breakpoint (id 0) for bp_2 function - changes that breakpoint to bp_1 function - waits for the breakpoint to hit and checks it has proper rip of bp_1 function This test aims on an issue in kernel preventing to change disabled breakpoints Second test mimics the first one except for few steps in the parent: - creates a new breakpoint (id 0) for bp_1 function - changes that breakpoint to bogus (-1) address - waits for the breakpoint to hit and checks it has proper rip of bp_1 function This test aims on an issue in kernel disabling enabled breakpoint after unsuccesful change. Committer testing: # uname -a Linux jouet 4.18.0-rc8-00002-g1236568ee3cb #12 SMP Tue Aug 7 14:08:26 -03 2018 x86_64 x86_64 x86_64 GNU/Linux # perf test -v "bp modify" 62: x86 bp modify : --- start --- test child forked, pid 25671 in bp_1 tracee exited prematurely 2 FAILED arch/x86/tests/bp-modify.c:209 modify test 1 failed test child finished with -1 ---- end ---- x86 bp modify: FAILED! # Signed-off-by: Jiri Olsa <[email protected]> Tested-by: Arnaldo Carvalho de Melo <[email protected]> Cc: Alexander Shishkin <[email protected]> Cc: David Ahern <[email protected]> Cc: Milind Chabbi <[email protected]> Cc: Namhyung Kim <[email protected]> Cc: Oleg Nesterov <[email protected]> Cc: Peter Zijlstra <[email protected]> Link: http://lkml.kernel.org/r/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
2018-08-30perf annotate: Properly interpret indirect callMartin Liška1-2/+8
The patch changes the parsing of: callq *0x8(%rbx) from: 0.26 │ → callq *8 to: 0.26 │ → callq *0x8(%rbx) in this case an address is followed by a register, thus one can't parse only the address. Committer testing: 1) run 'perf record sleep 10' 2) before applying the patch, run: perf annotate --stdio2 > /tmp/before 3) after applying the patch, run: perf annotate --stdio2 > /tmp/after 4) diff /tmp/before /tmp/after: --- /tmp/before 2018-08-28 11:16:03.238384143 -0300 +++ /tmp/after 2018-08-28 11:15:39.335341042 -0300 @@ -13274,7 +13274,7 @@ ↓ jle 128 hash_value = hash_table->hash_func (key); mov 0x8(%rsp),%rdi - 0.91 → callq *30 + 0.91 → callq *0x30(%r12) mov $0x2,%r8d cmp $0x2,%eax node_hash = hash_table->hashes[node_index]; @@ -13848,7 +13848,7 @@ mov %r14,%rdi sub %rbx,%r13 mov %r13,%rdx - → callq *38 + → callq *0x38(%r15) cmp %rax,%r13 1.91 ↓ je 240 1b4: mov $0xffffffff,%r13d @@ -14026,7 +14026,7 @@ mov %rcx,-0x500(%rbp) mov %r15,%rsi mov %r14,%rdi - → callq *38 + → callq *0x38(%rax) mov -0x500(%rbp),%rcx cmp %rax,%rcx ↓ jne 9b0 <SNIP tons of other such cases> Signed-off-by: Martin Liška <[email protected]> Tested-by: Arnaldo Carvalho de Melo <[email protected]> Tested-by: Kim Phillips <[email protected]> Cc: Jiri Olsa <[email protected]> Link: http://lkml.kernel.org/r/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
2018-08-30Merge tag 'mtd/for-4.19-rc2' of git://git.infradead.org/linux-mtdLinus Torvalds2-2/+7
Pull mtd fixes from Boris Brezillon: "Raw NAND fixes: - denali: Fix a regression caused by the nand_scan() rework - docg4: Fix a build error when gcc decides to not iniline some functions (can be reproduced with gcc 4.1.2): * tag 'mtd/for-4.19-rc2' of git://git.infradead.org/linux-mtd: mtd: rawnand: denali: do not pass zero maxchips to nand_scan() mtd: rawnand: docg4: Remove wrong __init annotations
2018-08-30Merge tag 'mmc-v4.19-2' of ↵Linus Torvalds5-14/+25
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc Pull MMC fixes from Ulf Hansson: "MMC core: - Fix unsupported parallel dispatch of requests MMC host: - atmel-mci/android-goldfish: Fixup logic of sg_copy_{from,to}_buffer - renesas_sdhi_internal_dmac: Prevent IRQ-storm due of DMAC IRQs - renesas_sdhi_internal_dmac: Fixup bad register offset" * tag 'mmc-v4.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: mmc: renesas_sdhi_internal_dmac: mask DMAC interrupts mmc: renesas_sdhi_internal_dmac: fix #define RST_RESERVED_BITS mmc: block: Fix unsupported parallel dispatch of requests mmc: android-goldfish: fix bad logic of sg_copy_{from,to}_buffer conversion mmc: atmel-mci: fix bad logic of sg_copy_{from,to}_buffer conversion
2018-08-30tools/kvm_stat: re-animate display of dead guestsStefan Raspl1-0/+10
When filtering by guest (interactive commands 'p'/'g'), and the respective guest was destroyed, detect when the guest is up again through the guest name if possible. I.e. when displaying events for a specific guest, it is not necessary anymore to restart kvm_stat in case the guest is restarted. Signed-off-by: Stefan Raspl <[email protected]> Signed-off-by: Radim Krčmář <[email protected]>
2018-08-30tools/kvm_stat: indicate dead guests as suchStefan Raspl1-3/+9
For destroyed guests, kvm_stat essentially freezes with the last data displayed. This is acceptable for users, in case they want to inspect the final data. But it looks a bit irritating. Therefore, detect this situation and display a respective indicator in the header. Signed-off-by: Stefan Raspl <[email protected]> Signed-off-by: Radim Krčmář <[email protected]>
2018-08-30tools/kvm_stat: handle guest removals more gracefullyStefan Raspl1-2/+9
When running with the DebugFS provider, removal of a guest can result in a negative CurAvg/s, which looks rather confusing. If so, suppress the body refresh and print a message instead. To reproduce, have at least one guest A completely booted. Then start another guest B (which generates a huge amount of events), then destroy B. On the next refresh, kvm_stat should display a whole lot of negative values in the CurAvg/s column. Signed-off-by: Stefan Raspl <[email protected]> Signed-off-by: Radim Krčmář <[email protected]>
Powered by cgit, Gruvboxed by Blaster4385.