| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
John Ernberg says:
====================
net: fec: Fix to suspend / resume with mac_managed_pm
Since the introduction of mac_managed_pm in the FEC driver there were some
discrepancies regarding power management of the PHY.
This failed on our board that has a permanently powered Microchip LAN8700R
attached to the FEC. Although the root cause of the failure can be traced
back to f166f890c8f0 ("net: ethernet: fec: Replace interrupt driven MDIO
with polled IO") and probably even before that, we only started noticing
the problem going from 5.10 to 6.1.
Since 557d5dc83f68 ("net: fec: use mac-managed PHY PM") is actually a fix
to most of the power management sequencing problems that came with power
managing the MDIO bus which for the FEC meant adding a race with FEC
resume (and phy_start() if netif was running) and PHY resume.
That it worked before for us was probably just luck...
Thanks to Wei's response to my report at [1] I was able to pick up his
patch and start honing in on the remaining missing details.
[1]: https://lore.kernel.org/netdev/[email protected]/
v3: https://lore.kernel.org/netdev/[email protected]/
v2: https://lore.kernel.org/netdev/[email protected]/
v1: https://lore.kernel.org/netdev/[email protected]/
====================
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Setting mac_managed_pm during interface up is too late.
In situations where the link is not brought up yet and the system suspends
the regular PHY power management will run. Since the FEC ETHEREN control
bit is cleared (automatically) on suspend the controller is off in resume.
When the regular PHY power management resume path runs in this context it
will write to the MII_DATA register but nothing will be transmitted on the
MDIO bus.
This can be observed by the following log:
fec 5b040000.ethernet eth0: MDIO read timeout
Microchip LAN87xx T1 5b040000.ethernet-1:04: PM: dpm_run_callback(): mdio_bus_phy_resume+0x0/0xc8 returns -110
Microchip LAN87xx T1 5b040000.ethernet-1:04: PM: failed to resume: error -110
The data written will however remain in the MII_DATA register.
When the link later is set to administrative up it will trigger a call to
fec_restart() which will restore the MII_SPEED register. This triggers the
quirk explained in f166f890c8f0 ("net: ethernet: fec: Replace interrupt
driven MDIO with polled IO") causing an extra MII_EVENT.
This extra event desynchronizes all the MDIO register reads, causing them
to complete too early. Leading all reads to read as 0 because
fec_enet_mdio_wait() returns too early.
When a Microchip LAN8700R PHY is connected to the FEC, the 0 reads causes
the PHY to be initialized incorrectly and the PHY will not transmit any
ethernet signal in this state. It cannot be brought out of this state
without a power cycle of the PHY.
Fixes: 557d5dc83f68 ("net: fec: use mac-managed PHY PM")
Closes: https://lore.kernel.org/netdev/[email protected]/
Signed-off-by: Wei Fang <[email protected]>
[jernberg: commit message]
Signed-off-by: John Ernberg <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
In the very rare case where a packet type is unknown to the driver,
idpf_rx_process_skb_fields would return early without calling
eth_type_trans to set the skb protocol / the network layer handler.
This is especially problematic if tcpdump is running when such a
packet is received, i.e. it would cause a kernel panic.
Instead, call eth_type_trans for every single packet, even when
the packet type is unknown.
Fixes: 3a8845af66ed ("idpf: add RX splitq napi poll support")
Reported-by: Balazs Nemeth <[email protected]>
Signed-off-by: Joshua Hay <[email protected]>
Reviewed-by: Jesse Brandeburg <[email protected]>
Reviewed-by: Przemek Kitszel <[email protected]>
Tested-by: Salvatore Daniele <[email protected]>
Signed-off-by: Pavan Kumar Linga <[email protected]>
Tested-by: Krishneil Singh <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
If an inode is missing, but corresponding extents and dirent still
exist, it's well worth recreating it - this does so.
Signed-off-by: Kent Overstreet <[email protected]>
|
|
We can now recreate missing subvolumes from dirents and/or inodes.
Signed-off-by: Kent Overstreet <[email protected]>
|
|
In backpointer repair, if we get a missing backpointer - but there's
already a backpointer that points to an existing extent - we've got
multiple extents that point to the same space and need to decide which
to keep.
Signed-off-by: Kent Overstreet <[email protected]>
|
|
When the snapshots btree is going, we'll have to delete huge amounts of
data - unless we can reconstruct it by looking at the keys that refer to
it.
Signed-off-by: Kent Overstreet <[email protected]>
|
|
We need this to know when we should attempt to reconstruct the snapshots
btree
Signed-off-by: Kent Overstreet <[email protected]>
|
|
With the new btree node scan code, we can now recover from corrupt btree
roots - simply create a new fake root at depth 1, and then insert all
the leaves we found.
If the root wasn't corrupt but there's corruption elsewhere in the
btree, we can fill in holes as needed with the newest version of a given
node(s) from the scan; we also check if a given btree node is older than
what we found from the scan.
Signed-off-by: Kent Overstreet <[email protected]>
|
|
If a btree root or interior btree node goes bad, we're going to lose a
lot of data, unless we can recover the nodes that it pointed to by
scanning.
Fortunately btree node headers are fully self describing, and
additionally the magic number is xored with the filesytem UUID, so we
can do so safely.
This implements the scanning - next patch will rework topology repair to
make use of the found nodes.
Signed-off-by: Kent Overstreet <[email protected]>
|
|
When a btree root is unreadable, we might still have keys fro the
journal to walk and mark.
Signed-off-by: Kent Overstreet <[email protected]>
|
|
Signed-off-by: Kent Overstreet <[email protected]>
|
|
Pull out eytzinger.c and kill eytzinger_cmp_fn. We now provide
eytzinger0_sort and eytzinger0_sort_r, which use the standard cmp_func_t
and cmp_r_func_t callbacks.
Signed-off-by: Kent Overstreet <[email protected]>
|
|
Signed-off-by: Kent Overstreet <[email protected]>
|
|
Signed-off-by: Kent Overstreet <[email protected]>
|
|
ICL supposedly doesn't support FEC on MST. Reject it.
Cc: [email protected]
Fixes: d51f25eb479a ("drm/i915: Add DSC support to MST path")
Reviewed-by: Uma Shankar <[email protected]>
Signed-off-by: Ville Syrjälä <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
(cherry picked from commit b648ce2a28ba83c4fa67c61fcc5983e15e9d4afb)
Signed-off-by: Rodrigo Vivi <[email protected]>
|
|
The MST code currently assumes that glk+ already supports MST+DSC,
which is incorrect. We need to check for TGL+ actually. ICL does
support SST+DSC, but supposedly it can't do MST+FEC which will
also rule out MST+DSC.
Note that a straight TGL+ check doesn't work here because DSC
support can get fused out, so we do need to also check 'has_dsc'.
Cc: [email protected]
Fixes: d51f25eb479a ("drm/i915: Add DSC support to MST path")
Reviewed-by: Uma Shankar <[email protected]>
Signed-off-by: Ville Syrjälä <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
(cherry picked from commit c9c92f286dbdf872390ef3e74dbe5f0641e46f55)
Signed-off-by: Rodrigo Vivi <[email protected]>
|
|
For DISPLAY < 13, compressed bpp is chosen from a list of
supported compressed bpps. Fix the condition to choose the
appropriate compressed bpp from the list.
Fixes: 1c56e9a39833 ("drm/i915/dp: Get optimal link config to have best compressed bpp")
Cc: Ankit Nautiyal <[email protected]>
Cc: Stanislav Lisovskiy <[email protected]>
Cc: Jani Nikula <[email protected]>
Cc: <[email protected]> # v6.7+
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/10162
Signed-off-by: Ankit Nautiyal <[email protected]>
Reviewed-by: Suraj Kandpal <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
(cherry picked from commit 5a1da42b50f3594e18738885c2f23ed36629dd00)
Signed-off-by: Rodrigo Vivi <[email protected]>
|
|
Enable only one CCS engine by default with all the compute sices
allocated to it.
While generating the list of UABI engines to be exposed to the
user, exclude any additional CCS engines beyond the first
instance.
This change can be tested with igt i915_query.
Fixes: d2eae8e98d59 ("drm/i915/dg2: Drop force_probe requirement")
Signed-off-by: Andi Shyti <[email protected]>
Cc: Chris Wilson <[email protected]>
Cc: Joonas Lahtinen <[email protected]>
Cc: Matt Roper <[email protected]>
Cc: <[email protected]> # v6.2+
Reviewed-by: Matt Roper <[email protected]>
Acked-by: Michal Mrozek <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
(cherry picked from commit 2bebae0112b117de7e8a7289277a4bd2403b9e17)
Signed-off-by: Rodrigo Vivi <[email protected]>
|
|
We want a fixed load CCS balancing consisting in all slices
sharing one single user engine. For this reason do not create the
intel_engine_cs structure with its dedicated command streamer for
CCS slices beyond the first.
Fixes: d2eae8e98d59 ("drm/i915/dg2: Drop force_probe requirement")
Signed-off-by: Andi Shyti <[email protected]>
Cc: Chris Wilson <[email protected]>
Cc: Joonas Lahtinen <[email protected]>
Cc: Matt Roper <[email protected]>
Cc: <[email protected]> # v6.2+
Acked-by: Michal Mrozek <[email protected]>
Reviewed-by: Matt Roper <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
(cherry picked from commit c7a5aa4e57f88470313a8277eb299b221b86e3b1)
Signed-off-by: Rodrigo Vivi <[email protected]>
|
|
The hardware should not dynamically balance the load between CCS
engines. Wa_14019159160 recommends disabling it across all
platforms.
Fixes: d2eae8e98d59 ("drm/i915/dg2: Drop force_probe requirement")
Signed-off-by: Andi Shyti <[email protected]>
Cc: Chris Wilson <[email protected]>
Cc: Joonas Lahtinen <[email protected]>
Cc: Matt Roper <[email protected]>
Cc: <[email protected]> # v6.2+
Reviewed-by: Matt Roper <[email protected]>
Acked-by: Michal Mrozek <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
(cherry picked from commit f5d2904cf814f20b79e3e4c1b24a4ccc2411b7e0)
Signed-off-by: Rodrigo Vivi <[email protected]>
|
|
Commit 9bb66c179f50 ("drm/i915: Reserve some kernel space per
vm") reduces the available VM space of one page in order to apply
Wa_16018031267 and Wa_16018063123.
This page was reserved indiscrimitely in all platforms even when
not needed. Limit it to DG2 onwards.
Fixes: 9bb66c179f50 ("drm/i915: Reserve some kernel space per vm")
Signed-off-by: Andi Shyti <[email protected]>
Cc: Andrzej Hajda <[email protected]>
Cc: Chris Wilson <[email protected]>
Cc: Jonathan Cavitt <[email protected]>
Cc: Nirmoy Das <[email protected]>
Reviewed-by: Nirmoy Das <[email protected]>
Acked-by: Michal Mrozek <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
(cherry picked from commit 9721634441d5dedba7f9eebb2bf0c9411cbafc4e)
Signed-off-by: Rodrigo Vivi <[email protected]>
|
|
Currently we are not aligning selective update area to cover cursor fully
when cursor is not updated by itself but still in the selective update
area. Fix this by checking cursor separately after
drm_atomic_add_affected_planes.
Bspec: 68927
Fixes: 1bff93b8bc27 ("drm/i915/psr: Extend SU area to cover cursor fully if needed")
Signed-off-by: Jouni Högander <[email protected]>
Reviewed-by: Mika Kahola <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
(cherry picked from commit d37b3dac68e26669f03f768b3afc9abc094c9ac9)
Signed-off-by: Rodrigo Vivi <[email protected]>
|
|
Currently PIPE_SRCSZ_ERLY_TPT is written in
intel_display.c:intel_set_pipe_src_size. This doesn't work as
intel_set_pipe_src_size is called only on modeset.
Bspec: 68927
Fixes: 3291bbb93e16 ("drm/i915/psr: Configure PIPE_SRCSZ_ERLY_TPT for psr2 early transport")
Signed-off-by: Jouni Högander <[email protected]>
Reviewed-by: Mika Kahola <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
(cherry picked from commit b52c4093b0c9089b00b42823d41986a94d32e341)
Signed-off-by: Rodrigo Vivi <[email protected]>
|
|
When early transport is enabled we need to write PIPE_SRCSZ_ERLY_TPT on
every flip doing selective update. This patch calculates
PIPE_SRCSZ_ERLY_TPT same way as is done for PSR2_MAN_TRK_CTL value and
stores i in intel_crtc_state->pipe_srcsz_early_tpt to be written later
during flip.
Bspec: 68927
Signed-off-by: Jouni Högander <[email protected]>
Reviewed-by: Mika Kahola <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
(cherry picked from commit f3b899f0b4b17fa0b20e27c23f78604d5686383d)
Signed-off-by: Rodrigo Vivi <[email protected]>
|
|
During probe the DMIC/SSP offload is enabled and it is not reversed on
remove.
Add a remove wrapper for LNL to disable the offload for DMIC and SSP
similarly to what is done during probe.
Signed-off-by: Peter Ujfalusi <[email protected]>
Reviewed-by: Pierre-Louis Bossart <[email protected]>
Reviewed-by: Bard Liao <[email protected]>
Link: https://msgid.link/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hansg/linux
Pull vboxsf fixes from Hans de Goede:
- Compiler warning fixes
- Explicitly deny setlease attempts
* tag 'vboxsf-v6.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/hansg/linux:
vboxsf: explicitly deny setlease attempts
vboxsf: Remove usage of the deprecated ida_simple_xx() API
vboxsf: Avoid an spurious warning if load_nls_xxx() fails
vboxsf: remove redundant variable out_len
|
|
Pull KVM fixes from Paolo Bonzini:
"ARM:
- Ensure perf events programmed to count during guest execution are
actually enabled before entering the guest in the nVHE
configuration
- Restore out-of-range handler for stage-2 translation faults
- Several fixes to stage-2 TLB invalidations to avoid stale
translations, possibly including partial walk caches
- Fix early handling of architectural VHE-only systems to ensure E2H
is appropriately set
- Correct a format specifier warning in the arch_timer selftest
- Make the KVM banner message correctly handle all of the possible
configurations
RISC-V:
- Remove redundant semicolon in num_isa_ext_regs()
- Fix APLIC setipnum_le/be write emulation
- Fix APLIC in_clrip[x] read emulation
x86:
- Fix a bug in KVM_SET_CPUID{2,} where KVM looks at the wrong CPUID
entries (old vs. new) and ultimately neglects to clear PV_UNHALT
from vCPUs with HLT-exiting disabled
- Documentation fixes for SEV
- Fix compat ABI for KVM_MEMORY_ENCRYPT_OP
- Fix a 14-year-old goof in a declaration shared by host and guest;
the enabled field used by Linux when running as a guest pushes the
size of "struct kvm_vcpu_pv_apf_data" from 64 to 68 bytes. This is
really unconsequential because KVM never consumes anything beyond
the first 64 bytes, but the resulting struct does not match the
documentation
Selftests:
- Fix spelling mistake in arch_timer selftest"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (25 commits)
KVM: arm64: Rationalise KVM banner output
arm64: Fix early handling of FEAT_E2H0 not being implemented
KVM: arm64: Ensure target address is granule-aligned for range TLBI
KVM: arm64: Use TLBI_TTL_UNKNOWN in __kvm_tlb_flush_vmid_range()
KVM: arm64: Don't pass a TLBI level hint when zapping table entries
KVM: arm64: Don't defer TLB invalidation when zapping table entries
KVM: selftests: Fix __GUEST_ASSERT() format warnings in ARM's arch timer test
KVM: arm64: Fix out-of-IPA space translation fault handling
KVM: arm64: Fix host-programmed guest events in nVHE
RISC-V: KVM: Fix APLIC in_clrip[x] read emulation
RISC-V: KVM: Fix APLIC setipnum_le/be write emulation
RISC-V: KVM: Remove second semicolon
KVM: selftests: Fix spelling mistake "trigged" -> "triggered"
Documentation: kvm/sev: clarify usage of KVM_MEMORY_ENCRYPT_OP
Documentation: kvm/sev: separate description of firmware
KVM: SEV: fix compat ABI for KVM_MEMORY_ENCRYPT_OP
KVM: selftests: Check that PV_UNHALT is cleared when HLT exiting is disabled
KVM: x86: Use actual kvm_cpuid.base for clearing KVM_FEATURE_PV_UNHALT
KVM: x86: Introduce __kvm_get_hypervisor_cpuid() helper
KVM: SVM: Return -EINVAL instead of -EBUSY on attempt to re-init SEV/SEV-ES
...
|
|
Commit 08abce60d63f ("security: Introduce path_post_mknod hook")
introduced security_path_post_mknod(), to replace the IMA-specific call
to ima_post_path_mknod().
For symmetry with security_path_mknod(), security_path_post_mknod() was
called after a successful mknod operation, for any file type, rather
than only for regular files at the time there was the IMA call.
However, as reported by VFS maintainers, successful mknod operation does
not mean that the dentry always has an inode attached to it (for
example, not for FIFOs on a SAMBA mount).
If that condition happens, the kernel crashes when
security_path_post_mknod() attempts to verify if the inode associated to
the dentry is private.
Move security_path_post_mknod() where the ima_post_path_mknod() call was,
which is obviously correct from IMA/EVM perspective. IMA/EVM are the only
in-kernel users, and only need to inspect regular files.
Reported-by: Steve French <[email protected]>
Closes: https://lore.kernel.org/linux-kernel/CAH2r5msAVzxCUHHG8VKrMPUKQHmBpE6K9_vjhgDa1uAvwx4ppw@mail.gmail.com/
Suggested-by: Al Viro <[email protected]>
Fixes: 08abce60d63f ("security: Introduce path_post_mknod hook")
Signed-off-by: Roberto Sassu <[email protected]>
Reviewed-by: Christian Brauner <[email protected]>
Reviewed-by: Mimi Zohar <[email protected]>
Acked-by: Paul Moore <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
The srso_alias_untrain_ret() dummy thunk in the !CONFIG_MITIGATION_SRSO
case is there only for the altenative in CALL_UNTRAIN_RET to have
a symbol to resolve.
However, testing with kernels which don't have CONFIG_MITIGATION_SRSO
enabled, leads to the warning in patch_return() to fire:
missing return thunk: srso_alias_untrain_ret+0x0/0x10-0x0: eb 0e 66 66 2e
WARNING: CPU: 0 PID: 0 at arch/x86/kernel/alternative.c:826 apply_returns (arch/x86/kernel/alternative.c:826
Put in a plain "ret" there so that gcc doesn't put a return thunk in
in its place which special and gets checked.
In addition:
ERROR: modpost: "srso_alias_untrain_ret" [arch/x86/kvm/kvm-amd.ko] undefined!
make[2]: *** [scripts/Makefile.modpost:145: Module.symvers] Chyba 1
make[1]: *** [/usr/src/linux-6.8.3/Makefile:1873: modpost] Chyba 2
make: *** [Makefile:240: __sub-make] Chyba 2
since !SRSO builds would use the dummy return thunk as reported by
[email protected], https://bugzilla.kernel.org/show_bug.cgi?id=218679.
Reported-by: kernel test robot <[email protected]>
Closes: https://lore.kernel.org/oe-lkp/[email protected]
Signed-off-by: Borislav Petkov (AMD) <[email protected]>
Link: https://lore.kernel.org/all/[email protected]/
Signed-off-by: Linus Torvalds <[email protected]>
|
|
ice_port_vlan_on/off() was introduced in commit 2946204b3fa8 ("ice:
implement bridge port vlan"). But ice_port_vlan_on() incorrectly assigns
ena_rx_filtering to inner_vlan_ops in DVM mode.
This causes an error when rx_filtering cannot be enabled in legacy mode.
Reproducer:
echo 1 > /sys/class/net/$PF/device/sriov_numvfs
ip link set $PF vf 0 spoofchk off trust on vlan 3
dmesg:
ice 0000:41:00.0: failed to enable Rx VLAN filtering for VF 0 VSI 9 during VF rebuild, error -95
Fixes: 2946204b3fa8 ("ice: implement bridge port vlan")
Signed-off-by: Petr Oros <[email protected]>
Reviewed-by: Michal Swiatkowski <[email protected]>
Tested-by: Rafal Romanowski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Automatically cleaned up pointers need to be initialized before exiting
their scope. In this case, they need to be initialized to NULL before
any return statement.
Fixes: 90f821d72e11 ("ice: avoid unnecessary devm_ usage")
Signed-off-by: Dan Carpenter <[email protected]>
Reviewed-by: Jiri Pirko <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
This v6.8 change didn't make it into the release, send it as a fix for
v6.9.
|
|
IPA probe function was recently refactored to perform extra error checks
and make sure the thermal zone has trip points necessary for the IPA
operation. With this change, if a thermal zone is probed such that it
has no trip points that IPA can use, IPA will fail and the TZ won't be
created. This is the case if a platform defines a TZ without cooling
devices and only with "hot"/"critical" trip points, often found on some
Qualcomm devices [1].
Documentation across IPA code (notably get_governor_trips() kerneldoc)
suggests that IPA is supposed to handle such TZ even if it won't
actually do anything.
This commit partially reverts the previous change to allow IPA to bind
to such "empty" thermal zones.
Fixes: e83747c2f8e3 ("thermal: gov_power_allocator: Set up trip points earlier")
Link: arch/arm64/boot/dts/qcom/sc7180.dtsi#n4776 # [1]
Signed-off-by: Nikita Travkin <[email protected]>
Reviewed-by: Lukasz Luba <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
IPA was recently refactored to split out memory allocation into a
separate funciton. That funciton was made to return -EINVAL if there is
zero power_actors and thus no memory to allocate. This causes IPA to
fail probing when the thermal zone has no attached cooling devices.
Since cooling devices can attach after the thermal zone is created and
the governer is attached to it, failing probe due to the lack of cooling
devices is incorrect.
Change the allocate_actors_buffer() to return success when there is no
cooling devices present.
Fixes: 912e97c67cc3 ("thermal: gov_power_allocator: Move memory allocation out of throttle()")
Signed-off-by: Nikita Travkin <[email protected]>
Reviewed-by: Lukasz Luba <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
vboxsf does not break leases on its own, so it can't properly handle the
case where the hypervisor changes the data. Don't allow file leases on
vboxsf.
Signed-off-by: Jeff Layton <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Hans de Goede <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
|
|
ida_alloc() and ida_free() should be preferred to the deprecated
ida_simple_get() and ida_simple_remove().
This is less verbose.
Signed-off-by: Christophe JAILLET <[email protected]>
Link: https://lore.kernel.org/r/b3c057c86b73f0309a6362031d21f4d7ebb60587.1698835730.git.christophe.jaillet@wanadoo.fr
Reviewed-by: Hans de Goede <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
|
|
If an load_nls_xxx() function fails a few lines above, the 'sbi->bdi_id' is
still 0.
So, in the error handling path, we will call ida_simple_remove(..., 0)
which is not allocated yet.
In order to prevent a spurious "ida_free called for id=0 which is not
allocated." message, tweak the error handling path and add a new label.
Fixes: 0fd169576648 ("fs: Add VirtualBox guest shared folder (vboxsf) support")
Signed-off-by: Christophe JAILLET <[email protected]>
Link: https://lore.kernel.org/r/d09eaaa4e2e08206c58a1a27ca9b3e81dc168773.1698835730.git.christophe.jaillet@wanadoo.fr
Reviewed-by: Hans de Goede <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
|
|
The variable out_len is being used to accumulate the number of
bytes but it is not being used for any other purpose. The variable
is redundant and can be removed.
Cleans up clang scan build warning:
fs/vboxsf/utils.c:443:9: warning: variable 'out_len' set but not
used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Hans de Goede <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
|
|
kobject_get() errors
When a gpiochip gets added by loading a module, then another driver may
be waiting for that gpiochip to load on the deferred-probe list.
If the deferred-probe for the consumer of gpiochip then triggers between
the gpiodev_add_to_list_unlocked() calls which makes gpio_device_find()
see the chip and the gpiochip_setup_dev() later then gpio_device_find()
does a kobject_get() on an uninitialized kobject since the kobject is
initialized by gpiochip_setup_dev() calling device_initialize():
arizona spi-10WM5102:00: cannot find GPIO chip arizona, deferring
arizona spi-10WM5102:00: cannot find GPIO chip arizona, deferring
------------[ cut here ]------------
kobject: 'gpiochip5' (00000000241466f2): is not initialized, yet kobject_get() is being called.
WARNING: CPU: 3 PID: 42 at lib/kobject.c:640 kobject_get+0x43/0x70
Call Trace:
kobject_get
gpio_device_find
gpiod_find_and_request
gpiod_get
snd_byt_wm5102_mc_probe
Not only is the device not initialized yet, but when the gpio-device is
added to the list things like the irqchip also have not been initialized
yet.
So gpio_device_find() should really ignore the gpio-device until
gpiochip_add_data_with_key() is fully done. Add a device_is_registered()
check to gpio_device_find() to ignore gpio-devices on the list which are
not yet fully initialized.
Fixes: aab5c6f20023 ("gpio: set device type for GPIO chips")
Suggested-by: Bartosz Golaszewski <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
Reviewed-by: Andy Shevchenko <[email protected]>
[Bartosz: fix a typo in commit message]
Signed-off-by: Bartosz Golaszewski <[email protected]>
|
|
If the RBUF logic is not reset when the kernel starts then there
may be some data left over from any network boot loader. If the
64-byte packet headers are enabled then this can be fatal.
Extend bcmgenet_dma_disable to do perform the reset, but not when
called from bcmgenet_resume in order to preserve a wake packet.
N.B. This different handling of resume is just based on a hunch -
why else wouldn't one reset the RBUF as well as the TBUF? If this
isn't the case then it's easy to change the patch to make the RBUF
reset unconditional.
See: https://github.com/raspberrypi/linux/issues/3850
See: https://github.com/raspberrypi/firmware/issues/1882
Signed-off-by: Phil Elwell <[email protected]>
Signed-off-by: Maarten Vanraes <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In rvu_map_cgx_lmac_pf() the 'iter', which is used as an array index, can reach
value (up to 14) that exceed the size (MAX_LMAC_COUNT = 8) of the array.
Fix this bug by adding 'iter' value check.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 91c6945ea1f9 ("octeontx2-af: cn10k: Add RPM MAC support")
Signed-off-by: Aleksandr Mishin <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux
Pull selinux fix from Paul Moore:
"A single patch for SELinux to fix a problem where we could potentially
dereference an error pointer if we failed to successfully mount
selinuxfs"
* tag 'selinux-pr-20240402' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux:
selinux: avoid dereference of garbage after mount failure
|
|
Add myself as mlx5 core and EN maintainer.
Signed-off-by: Tariq Toukan <[email protected]>
Reviewed-by: Gal Pressman <[email protected]>
Acked-by: Saeed Mahameed <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
syzkaller reported infinite recursive calls of fib6_dump_done() during
netlink socket destruction. [1]
From the log, syzkaller sent an AF_UNSPEC RTM_GETROUTE message, and then
the response was generated. The following recvmmsg() resumed the dump
for IPv6, but the first call of inet6_dump_fib() failed at kzalloc() due
to the fault injection. [0]
12:01:34 executing program 3:
r0 = socket$nl_route(0x10, 0x3, 0x0)
sendmsg$nl_route(r0, ... snip ...)
recvmmsg(r0, ... snip ...) (fail_nth: 8)
Here, fib6_dump_done() was set to nlk_sk(sk)->cb.done, and the next call
of inet6_dump_fib() set it to nlk_sk(sk)->cb.args[3]. syzkaller stopped
receiving the response halfway through, and finally netlink_sock_destruct()
called nlk_sk(sk)->cb.done().
fib6_dump_done() calls fib6_dump_end() and nlk_sk(sk)->cb.done() if it
is still not NULL. fib6_dump_end() rewrites nlk_sk(sk)->cb.done() by
nlk_sk(sk)->cb.args[3], but it has the same function, not NULL, calling
itself recursively and hitting the stack guard page.
To avoid the issue, let's set the destructor after kzalloc().
[0]:
FAULT_INJECTION: forcing a failure.
name failslab, interval 1, probability 0, space 0, times 0
CPU: 1 PID: 432110 Comm: syz-executor.3 Not tainted 6.8.0-12821-g537c2e91d354-dirty #11
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl (lib/dump_stack.c:117)
should_fail_ex (lib/fault-inject.c:52 lib/fault-inject.c:153)
should_failslab (mm/slub.c:3733)
kmalloc_trace (mm/slub.c:3748 mm/slub.c:3827 mm/slub.c:3992)
inet6_dump_fib (./include/linux/slab.h:628 ./include/linux/slab.h:749 net/ipv6/ip6_fib.c:662)
rtnl_dump_all (net/core/rtnetlink.c:4029)
netlink_dump (net/netlink/af_netlink.c:2269)
netlink_recvmsg (net/netlink/af_netlink.c:1988)
____sys_recvmsg (net/socket.c:1046 net/socket.c:2801)
___sys_recvmsg (net/socket.c:2846)
do_recvmmsg (net/socket.c:2943)
__x64_sys_recvmmsg (net/socket.c:3041 net/socket.c:3034 net/socket.c:3034)
[1]:
BUG: TASK stack guard page was hit at 00000000f2fa9af1 (stack is 00000000b7912430..000000009a436beb)
stack guard page: 0000 [#1] PREEMPT SMP KASAN
CPU: 1 PID: 223719 Comm: kworker/1:3 Not tainted 6.8.0-12821-g537c2e91d354-dirty #11
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014
Workqueue: events netlink_sock_destruct_work
RIP: 0010:fib6_dump_done (net/ipv6/ip6_fib.c:570)
Code: 3c 24 e8 f3 e9 51 fd e9 28 fd ff ff 66 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 00 f3 0f 1e fa 41 57 41 56 41 55 41 54 55 48 89 fd <53> 48 8d 5d 60 e8 b6 4d 07 fd 48 89 da 48 b8 00 00 00 00 00 fc ff
RSP: 0018:ffffc9000d980000 EFLAGS: 00010293
RAX: 0000000000000000 RBX: ffffffff84405990 RCX: ffffffff844059d3
RDX: ffff8881028e0000 RSI: ffffffff84405ac2 RDI: ffff88810c02f358
RBP: ffff88810c02f358 R08: 0000000000000007 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000224 R12: 0000000000000000
R13: ffff888007c82c78 R14: ffff888007c82c68 R15: ffff888007c82c68
FS: 0000000000000000(0000) GS:ffff88811b100000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffc9000d97fff8 CR3: 0000000102309002 CR4: 0000000000770ef0
PKRU: 55555554
Call Trace:
<#DF>
</#DF>
<TASK>
fib6_dump_done (net/ipv6/ip6_fib.c:572 (discriminator 1))
fib6_dump_done (net/ipv6/ip6_fib.c:572 (discriminator 1))
...
fib6_dump_done (net/ipv6/ip6_fib.c:572 (discriminator 1))
fib6_dump_done (net/ipv6/ip6_fib.c:572 (discriminator 1))
netlink_sock_destruct (net/netlink/af_netlink.c:401)
__sk_destruct (net/core/sock.c:2177 (discriminator 2))
sk_destruct (net/core/sock.c:2224)
__sk_free (net/core/sock.c:2235)
sk_free (net/core/sock.c:2246)
process_one_work (kernel/workqueue.c:3259)
worker_thread (kernel/workqueue.c:3329 kernel/workqueue.c:3416)
kthread (kernel/kthread.c:388)
ret_from_fork (arch/x86/kernel/process.c:153)
ret_from_fork_asm (arch/x86/entry/entry_64.S:256)
Modules linked in:
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: syzkaller <[email protected]>
Signed-off-by: Kuniyuki Iwashima <[email protected]>
Reviewed-by: Eric Dumazet <[email protected]>
Reviewed-by: David Ahern <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
On some boards with this chip version the BIOS is buggy and misses
to reset the PHY page selector. This results in the PHY ID read
accessing registers on a different page, returning a more or
less random value. Fix this by resetting the page selector first.
Fixes: f1e911d5d0df ("r8169: add basic phylib support")
Cc: [email protected]
Signed-off-by: Heiner Kallweit <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Commit 82dfb540aeb2 ("VSOCK: Add virtio vsock vsockmon hooks") added
virtio_transport_deliver_tap_pkt() for handing packets to the
vsockmon device. However, in virtio_transport_send_pkt_work(),
the function is called before actually sending the packet (i.e.
before placing it in the virtqueue with virtqueue_add_sgs() and checking
whether it returned successfully).
Queuing the packet in the virtqueue can fail even multiple times.
However, in virtio_transport_deliver_tap_pkt() we deliver the packet
to the monitoring tap interface only the first time we call it.
This certainly avoids seeing the same packet replicated multiple times
in the monitoring interface, but it can show the packet sent with the
wrong timestamp or even before we succeed to queue it in the virtqueue.
Move virtio_transport_deliver_tap_pkt() after calling virtqueue_add_sgs()
and making sure it returned successfully.
Fixes: 82dfb540aeb2 ("VSOCK: Add virtio vsock vsockmon hooks")
Cc: [email protected]
Signed-off-by: Marco Pinna <[email protected]>
Reviewed-by: Stefano Garzarella <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
When the ax25 device is detaching, the ax25_dev_device_down()
calls ax25_ds_del_timer() to cleanup the slave_timer. When
the timer handler is running, the ax25_ds_del_timer() that
calls del_timer() in it will return directly. As a result,
the use-after-free bugs could happen, one of the scenarios
is shown below:
(Thread 1) | (Thread 2)
| ax25_ds_timeout()
ax25_dev_device_down() |
ax25_ds_del_timer() |
del_timer() |
ax25_dev_put() //FREE |
| ax25_dev-> //USE
In order to mitigate bugs, when the device is detaching, use
timer_shutdown_sync() to stop the timer.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Duoming Zhou <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Signed-off-by: Kent Overstreet <[email protected]>
|
|
In the discard worker, we were failing to validate the bucket state -
meaning a corrupt needs_discard btree could cause us to discard a bucket
that we shouldn't.
If check_alloc_info hasn't run yet we just want to bail out, otherwise
it's a filesystem inconsistent error.
Signed-off-by: Kent Overstreet <[email protected]>
|