Age | Commit message (Collapse) | Author | Files | Lines |
|
As made explicit by commit 03a283cdc8c8 ("net/mlx5: Kconfig: Make tc
offload depend on tc skb extension") tc skb extension is required for
offloading tc as well as bridges on switchdev capable ConnectX devices.
Signed-off-by: Niklas Schnelle <[email protected]>
Signed-off-by: Alexander Gordeev <[email protected]>
|
|
Fix virtual vs physical address confusion (which currently are the same).
Reviewed-by: Vasily Gorbik <[email protected]>
Signed-off-by: Alexander Gordeev <[email protected]>
|
|
Kernel Address Sanitizer uses 3 bits per byte to
encode memory. That is the number of bits the start
and end address of a memory range is shifted right
when the corresponding shadow memory is created for
that memory range.
The used memory mapping routine expects page-aligned
addresses, while the above described 3-bit shift might
turn the shadow memory range start and end boundaries
into non-page-aligned in case the size of the original
memory range is less than (PAGE_SIZE << 3). As result,
the resulting shadow memory range could be short on one
page.
Align on page boundary the start and end addresses when
mapping a shadow memory range and avoid the described
issue in the future.
Note, that does not fix a real problem, since currently
no virtual regions of size less than (PAGE_SIZE << 3)
exist.
Reviewed-by: Vasily Gorbik <[email protected]>
Signed-off-by: Alexander Gordeev <[email protected]>
|
|
Since commit 3b5c3f000c2e ("s390/kasan: move shadow mapping
to decompressor") the decompressor establishes mappings for
the shadow memory and sets initial protection attributes to
RWX. The decompressed kernel resets protection to RW+NX
later on.
In case a shadow memory range is not aligned on page boundary
(e.g. as result of mem= kernel command line parameter use),
the "Checked W+X mappings: FAILED, 1 W+X pages found" warning
hits.
Reported-by: Vasily Gorbik <[email protected]>
Fixes: 557b19709da9 ("s390/kasan: move shadow mapping to decompressor")
Reviewed-by: Vasily Gorbik <[email protected]>
Signed-off-by: Alexander Gordeev <[email protected]>
|
|
get_elfcorehdr_size() returns a size_t, so there is no real point to
store it in a u32.
Turn 'alloc_size' into a size_t.
Signed-off-by: Christophe JAILLET <[email protected]>
Link: https://lore.kernel.org/r/0756118c9058338f3040edb91971d0bfd100027b.1686688212.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Alexander Gordeev <[email protected]>
|
|
Avoid linker error for randomly generated config file that
has CONFIG_BRANCH_PROFILE_NONE enabled and make it similar
to riscv, x86 and also to commit 4bf3ec384edf ("s390: disable
branch profiling for vdso").
Reviewed-by: Vasily Gorbik <[email protected]>
Signed-off-by: Alexander Gordeev <[email protected]>
|
|
Currently, if the device is offline and all the channel paths are
either configured or varied offline, the associated subchannel gets
unregistered. Don't unregister the subchannel, instead unregister
offline device.
Signed-off-by: Vineeth Vijayan <[email protected]>
Reviewed-by: Peter Oberparleiter <[email protected]>
Signed-off-by: Alexander Gordeev <[email protected]>
|
|
These don't do anything anymore, the only user of the symbol was
VFIO_CCW/AP which already "depends on VFIO" and VFIO itself selects
IOMMU_API.
When this was added VFIO was wrongly doing "depends on IOMMU_API" which
required some contortions like this to ensure IOMMU_API was turned on.
Reviewed-by: Eric Farman <[email protected]>
Signed-off-by: Jason Gunthorpe <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Alexander Gordeev <[email protected]>
|
|
Commit f1045056c726 ("topology/sysfs: rework book and drawer topology
ifdefery") activates the book and drawer topology, previously activated by
CONFIG_SCHED_{BOOK,DRAWER}, dependent on the existence of certain macro
definitions. Hence, since then, CONFIG_SCHED_{BOOK,DRAWER} have no effect
and any further purpose.
Remove the obsolete configs SCHED_{BOOK,DRAWER}.
Signed-off-by: Lukas Bulwahn <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Alexander Gordeev <[email protected]>
|
|
pahole says:
struct compat_statfs64 {
...
u32 f_spare[4]; /* 68 16 */
/* size: 88, cachelines: 1, members: 12 */
/* padding: 4 */
struct statfs {
...
unsigned int f_spare[4]; /* 68 16 */
/* size: 88, cachelines: 1, members: 12 */
/* padding: 4 */
struct statfs64 {
...
unsigned int f_spare[4]; /* 68 16 */
/* size: 88, cachelines: 1, members: 12 */
/* padding: 4 */
One has to keep the existence of padding in mind when working with
these structs. Grow f_spare arrays to 5 in order to simplify things.
Acked-by: Heiko Carstens <[email protected]>
Signed-off-by: Ilya Leoshkevich <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Alexander Gordeev <[email protected]>
|
|
s390's struct statfs and struct statfs64 contain padding, which
field-by-field copying does not set. Initialize the respective structs
with zeros before filling them and copying them to userspace, like it's
already done for the compat versions of these structs.
Found by KMSAN.
[[email protected]: fixed typo in patch description]
Acked-by: Heiko Carstens <[email protected]>
Cc: [email protected] # v4.14+
Signed-off-by: Ilya Leoshkevich <[email protected]>
Reviewed-by: Andrew Morton <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Alexander Gordeev <[email protected]>
|
|
Use "a" constraint instead of "d" constraint to pass the state parameter to
the do_sqbs() inline assembly. This prevents that general purpose register
zero is used for the state parameter.
If the compiler would select general purpose register zero this would be
problematic for the used instruction in rsy format: the register used for
the state parameter is a base register. If the base register is general
purpose register zero the contents of the register are unexpectedly ignored
when the instruction is executed.
This only applies to z/VM guests using QIOASSIST with dedicated (pass through)
QDIO-based devices such as FCP [zfcp driver] as well as real OSA or
HiperSockets [qeth driver].
A possible symptom for this case using zfcp is the following repeating kernel
message pattern:
zfcp <devbusid>: A QDIO problem occurred
zfcp <devbusid>: A QDIO problem occurred
zfcp <devbusid>: qdio: ZFCP on SC <sc> using AI:1 QEBSM:1 PRI:1 TDD:1 SIGA: W
zfcp <devbusid>: A QDIO problem occurred
zfcp <devbusid>: A QDIO problem occurred
Each of the qdio problem message can be accompanied by the following entries
for the affected subchannel <sc> in
/sys/kernel/debug/s390dbf/qdio_error/hex_ascii for zfcp or qeth:
<sc> ccq: 69....
<sc> SQBS ERROR.
Reviewed-by: Benjamin Block <[email protected]>
Cc: Steffen Maier <[email protected]>
Fixes: 8129ee164267 ("[PATCH] s390: qdio V=V pass-through")
Cc: <[email protected]>
Signed-off-by: Heiko Carstens <[email protected]>
Signed-off-by: Alexander Gordeev <[email protected]>
|
|
The pointer to IPL Parameter Information Block is stored
in the absolute lowcore for later use by dump tools. That
pointer is a virtual address, though it should be physical
instead.
Note, this does not fix a real issue, since virtual and
physical addresses are currently the same.
Suggested-by: Heiko Carstens <[email protected]>
Reviewed-by: Heiko Carstens <[email protected]>
Signed-off-by: Alexander Gordeev <[email protected]>
|
|
When SMT thread CPUs are added to CPU masks the nr_cpu_ids
limit is not checked and could be exceeded. This leads to
a warning for example if CONFIG_DEBUG_PER_CPU_MAPS is set
and the command line parameter nr_cpus is set to 1.
Reviewed-by: Heiko Carstens <[email protected]>
Signed-off-by: Alexander Gordeev <[email protected]>
|
|
Currently when the new channel-path is enabled, we do evaluation only
on the subchannels with a device connected on it. This is because,
in the past, if the device in the subchannel is not working or not
available, we used to unregister the subchannels. But, from the 'commit
2297791c92d0 ("s390/cio: dont unregister subchannel from child-drivers")'
we allow subchannels with or without an active device connected
on it. So, when we do the io_subchannel_verify, make sure that,
we are evaluating the subchannels without any device too.
Fixes: 2297791c92d0 ("s390/cio: dont unregister subchannel from child-drivers")
Reported-by: Boris Fiuczynski <[email protected]>
Signed-off-by: Vineeth Vijayan <[email protected]>
Reviewed-by: Peter Oberparleiter <[email protected]>
Signed-off-by: Alexander Gordeev <[email protected]>
|
|
Set CONFIG_INIT_STACK_NONE=y in defconfigs to avoid the extra overhead of
initializing all stack variables by default. Users who want to have that
must change the configuration on their own.
Signed-off-by: Heiko Carstens <[email protected]>
Signed-off-by: Alexander Gordeev <[email protected]>
|
|
Key blobs for the IOCTLs PKEY_KBLOB2PROTK[23] may contain clear key
material. Zeroize the copies of these keys in kernel memory after
creating the protected key.
Reviewed-by: Harald Freudenberger <[email protected]>
Signed-off-by: Holger Dengler <[email protected]>
Signed-off-by: Alexander Gordeev <[email protected]>
|
|
Commit 349d03ffd5f6 ("crypto: s390 - add crypto library interface for
ChaCha20") added a library interface to the s390 specific ChaCha20
implementation. However no check was added to verify if the required
facilities are installed before branching into the assembler code.
If compiled into the kernel, this will lead to the following crash,
if vector instructions are not available:
data exception: 0007 ilc:3 [#1] SMP
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 6.3.0-rc7+ #11
Hardware name: IBM 3931 A01 704 (KVM/Linux)
Krnl PSW : 0704e00180000000 000000001857277a (chacha20_vx+0x32/0x818)
R:0 T:1 IO:1 EX:1 Key:0 M:1 W:0 P:0 AS:3 CC:2 PM:0 RI:0 EA:3
Krnl GPRS: 0000037f0000000a ffffffffffffff60 000000008184b000 0000000019f5c8e6
0000000000000109 0000037fffb13c58 0000037fffb13c78 0000000019bb1780
0000037fffb13c58 0000000019f5c8e6 000000008184b000 0000000000000109
00000000802d8000 0000000000000109 0000000018571ebc 0000037fffb13718
Krnl Code: 000000001857276a: c07000b1f80b larl %r7,0000000019bb1780
0000000018572770: a708000a lhi %r0,10
#0000000018572774: e78950000c36 vlm %v24,%v25,0(%r5),0
>000000001857277a: e7a060000806 vl %v26,0(%r6),0
0000000018572780: e7bf70004c36 vlm %v27,%v31,0(%r7),4
0000000018572786: e70b00000456 vlr %v0,%v27
000000001857278c: e71800000456 vlr %v1,%v24
0000000018572792: e74b00000456 vlr %v4,%v27
Call Trace:
[<000000001857277a>] chacha20_vx+0x32/0x818
Last Breaking-Event-Address:
[<0000000018571eb6>] chacha20_crypt_s390.constprop.0+0x6e/0xd8
---[ end trace 0000000000000000 ]---
Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
Fix this by adding a missing MACHINE_HAS_VX check.
Fixes: 349d03ffd5f6 ("crypto: s390 - add crypto library interface for ChaCha20")
Reported-by: Marc Hartmayer <[email protected]>
Cc: <[email protected]> # 5.19+
Reviewed-by: Harald Freudenberger <[email protected]>
[[email protected]: remove duplicates in commit message]
Signed-off-by: Heiko Carstens <[email protected]>
Signed-off-by: Alexander Gordeev <[email protected]>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl
Pull compute express link fixes from Dan Williams:
- Fix a compilation issue with DEFINE_STATIC_SRCU() in the unit tests
- Fix leaking kernel memory to a root-only sysfs attribute
* tag 'cxl-fixes-6.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl:
cxl: Add missing return to cdat read error path
tools/testing/cxl: Use DEFINE_STATIC_SRCU()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc architecture fixes from Helge Deller:
- Fix encoding of swp_entry due to added SWP_EXCLUSIVE flag
- Include reboot.h to avoid gcc-12 compiler warning
* tag 'parisc-for-6.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix encoding of swp_entry due to added SWP_EXCLUSIVE flag
parisc: kexec: include reboot.h
|
|
Pull ARM fixes from Russell King:
- fix unwinder for uleb128 case
- fix kernel-doc warnings for HP Jornada 7xx
- fix unbalanced stack on vfp success path
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 9297/1: vfp: avoid unbalanced stack on 'success' return path
ARM: 9296/1: HP Jornada 7XX: fix kernel-doc warnings
ARM: 9295/1: unwind:fix unwind abort for uleb128 case
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fix from Borislav Petkov:
- Make sure __down_read_common() is always inlined so that the callers'
names land in traceevents output and thus the blocked function can be
identified
* tag 'locking_urgent_for_v6.4_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/rwsem: Add __always_inline annotation to __down_read_common() and inlined callers
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Borislav Petkov:
- Make sure the PEBS buffer is flushed before reprogramming the
hardware so that the correct record sizes are used
- Update the sample size for AMD BRS events
- Fix a confusion with using the same on-stack struct with different
events in the event processing path
* tag 'perf_urgent_for_v6.4_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel/ds: Flush PEBS DS when changing PEBS_DATA_CFG
perf/x86: Fix missing sample size update on AMD BRS
perf/core: Fix perf_sample_data not properly initialized for different swevents in perf_tp_event()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fix from Borislav Petkov:
- Fix a couple of kernel-doc warnings
* tag 'sched_urgent_for_v6.4_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: fix cid_lock kernel-doc warnings
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fix from Borislav Petkov:
- Add the required PCI IDs so that the generic SMN accesses provided by
amd_nb.c work for drivers which switch to them. Add a PCI device ID
to k10temp's table so that latter is loaded on such systems too
* tag 'x86_urgent_for_v6.4_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
hwmon: (k10temp) Add PCI ID for family 19, model 78h
x86/amd_nb: Add PCI ID for family 19h model 78h
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fix from Borislav Petkov:
- Prevent CPU state corruption when an active clockevent broadcast
device is replaced while the system is already in oneshot mode
* tag 'timers_urgent_for_v6.4_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick/broadcast: Make broadcast device replacement work correctly
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"Some ext4 bug fixes (mostly to address Syzbot reports)"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: bail out of ext4_xattr_ibody_get() fails for any reason
ext4: add bounds checking in get_max_inline_xattr_value_size()
ext4: add indication of ro vs r/w mounts in the mount message
ext4: fix deadlock when converting an inline directory in nojournal mode
ext4: improve error recovery code paths in __ext4_remount()
ext4: improve error handling from ext4_dirhash()
ext4: don't clear SB_RDONLY when remounting r/w until quota is re-enabled
ext4: check iomap type only if ext4_iomap_begin() does not fail
ext4: avoid a potential slab-out-of-bounds in ext4_group_desc_csum
ext4: fix data races when using cached status extents
ext4: avoid deadlock in fs reclaim with page writeback
ext4: fix invalid free tracking in ext4_xattr_move_to_block()
ext4: remove a BUG_ON in ext4_mb_release_group_pa()
ext4: allow ext4_get_group_info() to fail
ext4: fix lockdep warning when enabling MMP
ext4: fix WARNING in mb_find_extent
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev
Pull fbdev fixes from Helge Deller:
- use after free fix in imsttfb (Zheng Wang)
- fix error handling in arcfb (Zongjie Li)
- lots of whitespace cleanups (Thomas Zimmermann)
- add 1920x1080 modedb entry (me)
* tag 'fbdev-for-6.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev:
fbdev: stifb: Fix info entry in sti_struct on error path
fbdev: modedb: Add 1920x1080 at 60 Hz video mode
fbdev: imsttfb: Fix use after free bug in imsttfb_probe
fbdev: vfb: Remove trailing whitespaces
fbdev: valkyriefb: Remove trailing whitespaces
fbdev: stifb: Remove trailing whitespaces
fbdev: sa1100fb: Remove trailing whitespaces
fbdev: platinumfb: Remove trailing whitespaces
fbdev: p9100: Remove trailing whitespaces
fbdev: maxinefb: Remove trailing whitespaces
fbdev: macfb: Remove trailing whitespaces
fbdev: hpfb: Remove trailing whitespaces
fbdev: hgafb: Remove trailing whitespaces
fbdev: g364fb: Remove trailing whitespaces
fbdev: controlfb: Remove trailing whitespaces
fbdev: cg14: Remove trailing whitespaces
fbdev: atmel_lcdfb: Remove trailing whitespaces
fbdev: 68328fb: Remove trailing whitespaces
fbdev: arcfb: Fix error handling in arcfb_probe()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fix from James Bottomley:
"A single small fix for the UFS driver to fix a power management
failure"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: core: Fix I/O hang that occurs when BKOPS fails in W-LUN suspend
|
|
Fix the __swp_offset() and __swp_entry() macros due to commit 6d239fc78c0b
("parisc/mm: support __HAVE_ARCH_PTE_SWP_EXCLUSIVE") which introduced the
SWP_EXCLUSIVE flag by reusing the _PAGE_ACCESSED flag.
Reported-by: Christoph Biedl <[email protected]>
Tested-by: Christoph Biedl <[email protected]>
Reviewed-by: David Hildenbrand <[email protected]>
Signed-off-by: Helge Deller <[email protected]>
Fixes: 6d239fc78c0b ("parisc/mm: support __HAVE_ARCH_PTE_SWP_EXCLUSIVE")
Cc: <[email protected]> # v6.3+
|
|
In ext4_update_inline_data(), if ext4_xattr_ibody_get() fails for any
reason, it's best if we just fail as opposed to stumbling on,
especially if the failure is EFSCORRUPTED.
Cc: [email protected]
Signed-off-by: Theodore Ts'o <[email protected]>
|
|
Normally the extended attributes in the inode body would have been
checked when the inode is first opened, but if someone is writing to
the block device while the file system is mounted, it's possible for
the inode table to get corrupted. Add bounds checking to avoid
reading beyond the end of allocated memory if this happens.
Reported-by: [email protected]
Link: https://syzkaller.appspot.com/bug?extid=1966db24521e5f6e23f7
Cc: [email protected]
Signed-off-by: Theodore Ts'o <[email protected]>
|
|
Whether the file system is mounted read-only or read/write is more
important than the quota mode, which we are already printing. Add the
ro vs r/w indication since this can be helpful in debugging problems
from the console log.
Signed-off-by: Theodore Ts'o <[email protected]>
|
|
In no journal mode, ext4_finish_convert_inline_dir() can self-deadlock
by calling ext4_handle_dirty_dirblock() when it already has taken the
directory lock. There is a similar self-deadlock in
ext4_incvert_inline_data_nolock() for data files which we'll fix at
the same time.
A simple reproducer demonstrating the problem:
mke2fs -Fq -t ext2 -O inline_data -b 4k /dev/vdc 64
mount -t ext4 -o dirsync /dev/vdc /vdc
cd /vdc
mkdir file0
cd file0
touch file0
touch file1
attr -s BurnSpaceInEA -V abcde .
touch supercalifragilisticexpialidocious
Cc: [email protected]
Link: https://lore.kernel.org/r/[email protected]
Reported-by: [email protected]
Link: https://syzkaller.appspot.com/bug?id=ba84cc80a9491d65416bc7877e1650c87530fe8a
Signed-off-by: Theodore Ts'o <[email protected]>
|
|
If there are failures while changing the mount options in
__ext4_remount(), we need to restore the old mount options.
This commit fixes two problem. The first is there is a chance that we
will free the old quota file names before a potential failure leading
to a use-after-free. The second problem addressed in this commit is
if there is a failed read/write to read-only transition, if the quota
has already been suspended, we need to renable quota handling.
Cc: [email protected]
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Theodore Ts'o <[email protected]>
|
|
The ext4_dirhash() will *almost* never fail, especially when the hash
tree feature was first introduced. However, with the addition of
support of encrypted, casefolded file names, that function can most
certainly fail today.
So make sure the callers of ext4_dirhash() properly check for
failures, and reflect the errors back up to their callers.
Cc: [email protected]
Link: https://lore.kernel.org/r/[email protected]
Reported-by: [email protected]
Reported-by: [email protected]
Link: https://syzkaller.appspot.com/bug?id=db56459ea4ac4a676ae4b4678f633e55da005a9b
Signed-off-by: Theodore Ts'o <[email protected]>
|
|
When a file system currently mounted read/only is remounted
read/write, if we clear the SB_RDONLY flag too early, before the quota
is initialized, and there is another process/thread constantly
attempting to create a directory, it's possible to trigger the
WARN_ON_ONCE(dquot_initialize_needed(inode));
in ext4_xattr_block_set(), with the following stack trace:
WARNING: CPU: 0 PID: 5338 at fs/ext4/xattr.c:2141 ext4_xattr_block_set+0x2ef2/0x3680
RIP: 0010:ext4_xattr_block_set+0x2ef2/0x3680 fs/ext4/xattr.c:2141
Call Trace:
ext4_xattr_set_handle+0xcd4/0x15c0 fs/ext4/xattr.c:2458
ext4_initxattrs+0xa3/0x110 fs/ext4/xattr_security.c:44
security_inode_init_security+0x2df/0x3f0 security/security.c:1147
__ext4_new_inode+0x347e/0x43d0 fs/ext4/ialloc.c:1324
ext4_mkdir+0x425/0xce0 fs/ext4/namei.c:2992
vfs_mkdir+0x29d/0x450 fs/namei.c:4038
do_mkdirat+0x264/0x520 fs/namei.c:4061
__do_sys_mkdirat fs/namei.c:4076 [inline]
__se_sys_mkdirat fs/namei.c:4074 [inline]
__x64_sys_mkdirat+0x89/0xa0 fs/namei.c:4074
Cc: [email protected]
Link: https://lore.kernel.org/r/[email protected]
Reported-by: [email protected]
Link: https://syzkaller.appspot.com/bug?id=6513f6cb5cd6b5fc9f37e3bb70d273b94be9c34c
Signed-off-by: Theodore Ts'o <[email protected]>
|
|
When ext4_iomap_overwrite_begin() calls ext4_iomap_begin() map blocks may
fail for some reason (e.g. memory allocation failure, bare disk write), and
later because "iomap->type ! = IOMAP_MAPPED" triggers WARN_ON(). When ext4
iomap_begin() returns an error, it is normal that the type of iomap->type
may not match the expectation. Therefore, we only determine if iomap->type
is as expected when ext4_iomap_begin() is executed successfully.
Cc: [email protected]
Reported-by: [email protected]
Link: https://lore.kernel.org/all/[email protected]
Signed-off-by: Baokun Li <[email protected]>
Reviewed-by: Jan Kara <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Theodore Ts'o <[email protected]>
|
|
When modifying the block device while it is mounted by the filesystem,
syzbot reported the following:
BUG: KASAN: slab-out-of-bounds in crc16+0x206/0x280 lib/crc16.c:58
Read of size 1 at addr ffff888075f5c0a8 by task syz-executor.2/15586
CPU: 1 PID: 15586 Comm: syz-executor.2 Not tainted 6.2.0-rc5-syzkaller-00205-gc96618275234 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/12/2023
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x1b1/0x290 lib/dump_stack.c:106
print_address_description+0x74/0x340 mm/kasan/report.c:306
print_report+0x107/0x1f0 mm/kasan/report.c:417
kasan_report+0xcd/0x100 mm/kasan/report.c:517
crc16+0x206/0x280 lib/crc16.c:58
ext4_group_desc_csum+0x81b/0xb20 fs/ext4/super.c:3187
ext4_group_desc_csum_set+0x195/0x230 fs/ext4/super.c:3210
ext4_mb_clear_bb fs/ext4/mballoc.c:6027 [inline]
ext4_free_blocks+0x191a/0x2810 fs/ext4/mballoc.c:6173
ext4_remove_blocks fs/ext4/extents.c:2527 [inline]
ext4_ext_rm_leaf fs/ext4/extents.c:2710 [inline]
ext4_ext_remove_space+0x24ef/0x46a0 fs/ext4/extents.c:2958
ext4_ext_truncate+0x177/0x220 fs/ext4/extents.c:4416
ext4_truncate+0xa6a/0xea0 fs/ext4/inode.c:4342
ext4_setattr+0x10c8/0x1930 fs/ext4/inode.c:5622
notify_change+0xe50/0x1100 fs/attr.c:482
do_truncate+0x200/0x2f0 fs/open.c:65
handle_truncate fs/namei.c:3216 [inline]
do_open fs/namei.c:3561 [inline]
path_openat+0x272b/0x2dd0 fs/namei.c:3714
do_filp_open+0x264/0x4f0 fs/namei.c:3741
do_sys_openat2+0x124/0x4e0 fs/open.c:1310
do_sys_open fs/open.c:1326 [inline]
__do_sys_creat fs/open.c:1402 [inline]
__se_sys_creat fs/open.c:1396 [inline]
__x64_sys_creat+0x11f/0x160 fs/open.c:1396
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
RIP: 0033:0x7f72f8a8c0c9
Code: 28 00 00 00 75 05 48 83 c4 28 c3 e8 f1 19 00 00 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b8 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007f72f97e3168 EFLAGS: 00000246 ORIG_RAX: 0000000000000055
RAX: ffffffffffffffda RBX: 00007f72f8bac050 RCX: 00007f72f8a8c0c9
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000020000280
RBP: 00007f72f8ae7ae9 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 00007ffd165348bf R14: 00007f72f97e3300 R15: 0000000000022000
Replace
le16_to_cpu(sbi->s_es->s_desc_size)
with
sbi->s_desc_size
It reduces ext4's compiled text size, and makes the code more efficient
(we remove an extra indirect reference and a potential byte
swap on big endian systems), and there is no downside. It also avoids the
potential KASAN / syzkaller failure, as a bonus.
Reported-by: [email protected]
Reported-by: [email protected]
Link: https://syzkaller.appspot.com/bug?id=70d28d11ab14bd7938f3e088365252aa923cff42
Link: https://syzkaller.appspot.com/bug?id=b85721b38583ecc6b5e72ff524c67302abbc30f3
Link: https://lore.kernel.org/all/[email protected]/
Fixes: 717d50e4971b ("Ext4: Uninitialized Block Groups")
Cc: [email protected]
Signed-off-by: Tudor Ambarus <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Theodore Ts'o <[email protected]>
|
|
When using cached extent stored in extent status tree in tree->cache_es
another process holding ei->i_es_lock for reading can be racing with us
setting new value of tree->cache_es. If the compiler would decide to
refetch tree->cache_es at an unfortunate moment, it could result in a
bogus in_range() check. Fix the possible race by using READ_ONCE() when
using tree->cache_es only under ei->i_es_lock for reading.
Cc: [email protected]
Reported-by: [email protected]
Link: https://lore.kernel.org/all/[email protected]
Suggested-by: Dmitry Vyukov <[email protected]>
Signed-off-by: Jan Kara <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Theodore Ts'o <[email protected]>
|
|
Ext4 has a filesystem wide lock protecting ext4_writepages() calls to
avoid races with switching of journalled data flag or inode format. This
lock can however cause a deadlock like:
CPU0 CPU1
ext4_writepages()
percpu_down_read(sbi->s_writepages_rwsem);
ext4_change_inode_journal_flag()
percpu_down_write(sbi->s_writepages_rwsem);
- blocks, all readers block from now on
ext4_do_writepages()
ext4_init_io_end()
kmem_cache_zalloc(io_end_cachep, GFP_KERNEL)
fs_reclaim frees dentry...
dentry_unlink_inode()
iput() - last ref =>
iput_final() - inode dirty =>
write_inode_now()...
ext4_writepages() tries to acquire sbi->s_writepages_rwsem
and blocks forever
Make sure we cannot recurse into filesystem reclaim from writeback code
to avoid the deadlock.
Reported-by: [email protected]
Link: https://lore.kernel.org/all/[email protected]
Fixes: c8585c6fcaf2 ("ext4: fix races between changing inode journal mode and ext4_writepages")
CC: [email protected]
Signed-off-by: Jan Kara <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Theodore Ts'o <[email protected]>
|
|
In ext4_xattr_move_to_block(), the value of the extended attribute
which we need to move to an external block may be allocated by
kvmalloc() if the value is stored in an external inode. So at the end
of the function the code tried to check if this was the case by
testing entry->e_value_inum.
However, at this point, the pointer to the xattr entry is no longer
valid, because it was removed from the original location where it had
been stored. So we could end up calling kvfree() on a pointer which
was not allocated by kvmalloc(); or we could also potentially leak
memory by not freeing the buffer when it should be freed. Fix this by
storing whether it should be freed in a separate variable.
Cc: [email protected]
Link: https://lore.kernel.org/r/[email protected]
Link: https://syzkaller.appspot.com/bug?id=5c2aee8256e30b55ccf57312c16d88417adbd5e1
Link: https://syzkaller.appspot.com/bug?id=41a6b5d4917c0412eb3b3c3c604965bed7d7420b
Reported-by: [email protected]
Reported-by: [email protected]
Signed-off-by: Theodore Ts'o <[email protected]>
|
|
If a malicious fuzzer overwrites the ext4 superblock while it is
mounted such that the s_first_data_block is set to a very large
number, the calculation of the block group can underflow, and trigger
a BUG_ON check. Change this to be an ext4_warning so that we don't
crash the kernel.
Cc: [email protected]
Link: https://lore.kernel.org/r/[email protected]
Reported-by: [email protected]
Link: https://syzkaller.appspot.com/bug?id=69b28112e098b070f639efb356393af3ffec4220
Signed-off-by: Theodore Ts'o <[email protected]>
|
|
Previously, ext4_get_group_info() would treat an invalid group number
as BUG(), since in theory it should never happen. However, if a
malicious attaker (or fuzzer) modifies the superblock via the block
device while it is the file system is mounted, it is possible for
s_first_data_block to get set to a very large number. In that case,
when calculating the block group of some block number (such as the
starting block of a preallocation region), could result in an
underflow and very large block group number. Then the BUG_ON check in
ext4_get_group_info() would fire, resutling in a denial of service
attack that can be triggered by root or someone with write access to
the block device.
For a quality of implementation perspective, it's best that even if
the system administrator does something that they shouldn't, that it
will not trigger a BUG. So instead of BUG'ing, ext4_get_group_info()
will call ext4_error and return NULL. We also add fallback code in
all of the callers of ext4_get_group_info() that it might NULL.
Also, since ext4_get_group_info() was already borderline to be an
inline function, un-inline it. The results in a next reduction of the
compiled text size of ext4 by roughly 2k.
Cc: [email protected]
Link: https://lore.kernel.org/r/[email protected]
Reported-by: [email protected]
Link: https://syzkaller.appspot.com/bug?id=69b28112e098b070f639efb356393af3ffec4220
Signed-off-by: Theodore Ts'o <[email protected]>
Reviewed-by: Jan Kara <[email protected]>
|
|
Pull block fixes from Jens Axboe:
"Just a few minor fixes for drivers, and a deletion of a file that is
woefully out-of-date these days"
* tag 'block-6.4-2023-05-13' of git://git.kernel.dk/linux:
Documentation/block: drop the request.rst file
ublk: fix command op code check
block/rnbd: replace REQ_OP_FLUSH with REQ_OP_WRITE
nbd: Fix debugfs_create_dir error checking
|
|
Add a return to the error path when cxl_cdat_read_table() fails. Current
code continues with the table pointer points to freed memory.
Fixes: 7a877c923995 ("cxl/pci: Simplify CDAT retrieval error path")
Signed-off-by: Dave Jiang <[email protected]>
Reviewed-by: Davidlohr Bueso <[email protected]>
Link: https://lore.kernel.org/r/168382793506.3510737.4792518576623749076.stgit@djiang5-mobl3
Signed-off-by: Dan Williams <[email protected]>
|
|
Starting with commit:
95433f726301 ("srcu: Begin offloading srcu_struct fields to srcu_update")
...it is no longer possible to do:
static DEFINE_SRCU(x)
Switch to DEFINE_STATIC_SRCU(x) to fix:
tools/testing/cxl/test/mock.c:22:1: error: duplicate ‘static’
22 | static DEFINE_SRCU(cxl_mock_srcu);
| ^~~~~~
Reviewed-by: Dave Jiang <[email protected]>
Link: https://lore.kernel.org/r/168392709546.1135523.10424917245934547117.stgit@dwillia2-xfh.jf.intel.com
Signed-off-by: Dan Williams <[email protected]>
|
|
SYM_FUNC_START_LOCAL_NOALIGN() adds an endbr leading to this layout
(leaving only the last 2 bytes of the address):
3bff <zen_untrain_ret>:
3bff: f3 0f 1e fa endbr64
3c03: f6 test $0xcc,%bl
3c04 <__x86_return_thunk>:
3c04: c3 ret
3c05: cc int3
3c06: 0f ae e8 lfence
However, "the RET at __x86_return_thunk must be on a 64 byte boundary,
for alignment within the BTB."
Use SYM_START instead.
Signed-off-by: Borislav Petkov (AMD) <[email protected]>
Reviewed-by: Thomas Gleixner <[email protected]>
Cc: <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull more btrfs fixes from David Sterba:
- fix incorrect number of bitmap entries for space cache if loading is
interrupted by some error
- fix backref walking, this breaks a mode of LOGICAL_INO_V2 ioctl that
is used in deduplication tools
- zoned mode fixes:
- properly finish zone reserved for relocation
- correctly calculate super block zone end on ZNS
- properly initialize new extent buffer for redirty
- make mount option clear_cache work with block-group-tree, to rebuild
free-space-tree instead of temporarily disabling it that would lead
to a forced read-only mount
- fix alignment check for offset when printing extent item
* tag 'for-6.4-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: make clear_cache mount option to rebuild FST without disabling it
btrfs: zero the buffer before marking it dirty in btrfs_redirty_list_add
btrfs: zoned: fix full zone super block reading on ZNS
btrfs: zoned: zone finish data relocation BG with last IO
btrfs: fix backref walking not returning all inode refs
btrfs: fix space cache inconsistency after error loading it from disk
btrfs: print-tree: parent bytenr must be aligned to sector size
|