aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2020-09-01pktgen: fix error message with wrong function nameLeesoo Ahn1-1/+1
Error on calling kthread_create_on_node prints wrong function name, kernel_thread. Fixes: 94dcf29a11b3 ("kthread: use kthread_create_on_node()") Signed-off-by: Leesoo Ahn <[email protected]> Acked-by: Gustavo A. R. Silva <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-01arc: fix memory initialization for systems with two memory banksMike Rapoport1-11/+16
Rework of memory map initialization broke initialization of ARC systems with two memory banks. Before these changes, memblock was not aware of nodes configuration and the memory map was always allocated from the "lowmem" bank. After the addition of node information to memblock, the core mm attempts to allocate the memory map for the "highmem" bank from its node. The access to this memory using __va() fails because it can be only accessed using kmap. Anther problem that was uncovered is that {min,max}_high_pfn are calculated from u64 high_mem_start variable which prevents truncation to 32-bit physical address and the PFN values are above the node and zone boundaries. Use phys_addr_t type for high_mem_start and high_mem_size to ensure correspondence between PFNs and highmem zone boundaries and reserve the entire highmem bank until mem_init() to avoid accesses to it before highmem is enabled. To test this: 1. Enable HIGHMEM in ARC config 2. Enable 2 memory banks in haps_hs.dts (uncomment the 2nd bank) Fixes: 51930df5801e ("mm: free_area_init: allow defining max_zone_pfn in descending order") Cc: [email protected] [5.8] Signed-off-by: Mike Rapoport <[email protected]> Signed-off-by: Vineet Gupta <[email protected]> [vgupta: added instructions to test highmem]
2020-09-01Merge branch 'opp/fixes' of ↵Rafael J. Wysocki2-7/+17
git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm Pull operating performance points (OPP) framework fixes for 5.9-rc4 from Viresh Kumar: "This fixes reference counting for OPP tables. Few patches are getting queued (for various subsystems) for 5.10 which depend on this to be fixed first." * 'opp/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm: opp: Don't drop reference for an OPP table that was never parsed
2020-09-01ia64: fix min_low_pfn/max_low_pfn build errorsRandy Dunlap1-1/+1
Fix min_low_pfn/max_low_pfn build errors for arch/ia64/: (e.g.) ERROR: "max_low_pfn" [drivers/rpmsg/virtio_rpmsg_bus.ko] undefined! ERROR: "min_low_pfn" [drivers/rpmsg/virtio_rpmsg_bus.ko] undefined! ERROR: "min_low_pfn" [drivers/hwtracing/intel_th/intel_th_msu.ko] undefined! ERROR: "max_low_pfn" [drivers/hwtracing/intel_th/intel_th_msu.ko] undefined! ERROR: "min_low_pfn" [drivers/crypto/cavium/nitrox/n5pf.ko] undefined! ERROR: "max_low_pfn" [drivers/crypto/cavium/nitrox/n5pf.ko] undefined! ERROR: "max_low_pfn" [drivers/md/dm-integrity.ko] undefined! ERROR: "min_low_pfn" [drivers/md/dm-integrity.ko] undefined! ERROR: "max_low_pfn" [crypto/tcrypt.ko] undefined! ERROR: "min_low_pfn" [crypto/tcrypt.ko] undefined! ERROR: "min_low_pfn" [security/keys/encrypted-keys/encrypted-keys.ko] undefined! ERROR: "max_low_pfn" [security/keys/encrypted-keys/encrypted-keys.ko] undefined! ERROR: "min_low_pfn" [arch/ia64/kernel/mca_recovery.ko] undefined! ERROR: "max_low_pfn" [arch/ia64/kernel/mca_recovery.ko] undefined! David suggested just exporting min_low_pfn & max_low_pfn in mm/memblock.c: https://lore.kernel.org/lkml/alpine.DEB.2.22.394.2006291911220.1118534@chino.kir.corp.google.com/ Reported-by: kernel test robot <[email protected]> Signed-off-by: Randy Dunlap <[email protected]> Acked-by: David Rientjes <[email protected]> Acked-by: Tony Luck <[email protected]> Cc: [email protected] Cc: Andrew Morton <[email protected]> Cc: David Rientjes <[email protected]> Cc: Mike Rapoport <[email protected]> Cc: Tony Luck <[email protected]> Cc: Fenghua Yu <[email protected]> Cc: [email protected] Signed-off-by: Mike Rapoport <[email protected]>
2020-09-01perf report: Disable ordered_events for raw dumpJiri Olsa1-0/+3
Disable ordered_events for report raw dump, because for raw dump we want to see events as they are stored in the perf.data file, not sorted by time. Signed-off-by: Jiri Olsa <[email protected]> Cc: Alexander Shishkin <[email protected]> Cc: Ian Rogers <[email protected]> Cc: Michael Petlan <[email protected]> Cc: Namhyung Kim <[email protected]> Cc: Peter Zijlstra <[email protected]> Link: http://lore.kernel.org/lkml/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
2020-09-01perf tools: Correct SNOOPX field offsetAl Grant1-1/+1
perf_event.h has macros that define the field offsets in the data_src bitmask in perf records. The SNOOPX and REMOTE offsets were both 37. These are distinct fields, and the bitfield layout in perf_mem_data_src confirms that SNOOPX should be at offset 38. Committer notes: This was extracted from a larger patch that also contained kernel changes. Fixes: 52839e653b5629bd ("perf tools: Add support for printing new mem_info encodings") Signed-off-by: Al Grant <[email protected]> Reviewed-by: Andi Kleen <[email protected]> Cc: Adrian Hunter <[email protected]> Cc: Ian Rogers <[email protected]> Cc: Jiri Olsa <[email protected]> Cc: Namhyung Kim <[email protected]> Cc: Peter Zijlstra <[email protected]> Link: http://lore.kernel.org/lkml/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
2020-09-01perf intel-pt: Fix corrupt data after perf inject fromAl Grant1-1/+8
Commit 42bbabed09ce6208 ("perf tools: Add hw_idx in struct branch_stack") changed the format of branch stacks in perf samples. When samples use this new format, a flag must be set in the corresponding event. Synthesized branch stacks generated from Intel PT were using the new format, but not setting the event attribute, leading to consumers seeing corrupt data. This patch fixes the issue by setting the event attribute to indicate use of the new format. Fixes: 42bbabed09ce6208 ("perf tools: Add hw_idx in struct branch_stack") Signed-off-by: Al Grant <[email protected]> Acked-by: Adrian Hunter <[email protected]> Reviewed-by: Mathieu Poirier <[email protected]> Cc: Alexander Shishkin <[email protected]> Cc: Andi Kleen <[email protected]> Cc: Jiri Olsa <[email protected]> Cc: Kan Liang <[email protected]> Cc: Leo Yan <[email protected]> Cc: Mark Rutland <[email protected]> Cc: Mike Leach <[email protected]> Cc: Namhyung Kim <[email protected]> Cc: Peter Zijlstra <[email protected]> Cc: Suzuki Poulouse <[email protected]> Cc: [email protected] Link: http://lore.kernel.org/lkml/[email protected] Signed-off-by: Leo Yan <[email protected]> Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
2020-09-01perf cs-etm: Fix corrupt data after perf inject fromAl Grant1-1/+8
Commit 42bbabed09ce6208 ("perf tools: Add hw_idx in struct branch_stack") changed the format of branch stacks in perf samples. When samples use this new format, a flag must be set in the corresponding event. Synthesized branch stacks generated from CoreSight ETM trace were using the new format, but not setting the event attribute, leading to consumers seeing corrupt data. This patch fixes the issue by setting the event attribute to indicate use of the new format. Fixes: 42bbabed09ce6208 ("perf tools: Add hw_idx in struct branch_stack") Signed-off-by: Al Grant <[email protected]> Reviewed-by: Andrea Brunato <[email protected]> Cc: Adrian Hunter <[email protected]> Cc: Alexander Shishkin <[email protected]> Cc: Andi Kleen <[email protected]> Cc: Jiri Olsa <[email protected]> Cc: Kan Liang <[email protected]> Cc: Mark Rutland <[email protected]> Cc: Mathieu Poirier <[email protected]> Cc: Mike Leach <[email protected]> Cc: Namhyung Kim <[email protected]> Cc: Peter Zijlstra <[email protected]> Cc: Suzuki Poulouse <[email protected]> Cc: [email protected] Signed-off-by: Leo Yan <[email protected]> Link: http://lore.kernel.org/lkml/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
2020-09-01perf top/report: Fix infinite loop in the TUI for grouped eventsArnaldo Carvalho de Melo1-1/+2
For a while we need to have a dummy event for doing things like receiving PERF_RECORD_COMM, PERF_RECORD_EXEC, etc for threads being created and dying while we synthesize the pre-existing ones at tool start. This 'dummy' event is needed for keeping track of thread lifetime events early in the session but are uninteresting otherwise, i.e. no need to have it in a initial events menu for the non-grouped case, i.e. for: # perf top -e cycles,instructions or even for plain: # perf top When 'cycles' and that 'dummy' event are in place. The code to remove that 'dummy' event ended up creating an endless loop for the grouped case, i.e.: # perf top -e '{cycles,instructions}' Fix it. Fixes: bee9ca1c8a237ca1 ("perf report TUI: Remove needless 'dummy' event from menu") Cc: Adrian Hunter <[email protected]> Cc: Ian Rogers <[email protected]> Cc: Jiri Olsa <[email protected]> Cc: Namhyung Kim <[email protected]> Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
2020-09-01perf parse-events: Avoid an uninitialized read when using fake PMUsIan Rogers1-13/+17
With a fake_pmu the pmu_info isn't populated by perf_pmu__check_alias. In this case, don't try to copy the uninitialized values to the evsel. Signed-off-by: Ian Rogers <[email protected]> Acked-by: Jiri Olsa <[email protected]> Cc: Adrian Hunter <[email protected]> Cc: Alexander Shishkin <[email protected]> Cc: Andi Kleen <[email protected]> Cc: Jin Yao <[email protected]> Cc: Kajol Jain <[email protected]> Cc: Kan Liang <[email protected]> Cc: Leo Yan <[email protected]> Cc: Mark Rutland <[email protected]> Cc: Namhyung Kim <[email protected]> Cc: Peter Zijlstra <[email protected]> Cc: Stephane Eranian <[email protected]> Link: http://lore.kernel.org/lkml/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
2020-09-01perf stat: Fix out of bounds array access in the print_counters() evlist methodThomas Richter1-1/+1
Fix a compile error on F32 and gcc version 10.1 on s390 in file utils/stat-display.c. The error does not show up with make DEBUG=y. In fact the issue shows up when using both compiler options -O6 and -D_FORTIFY_SOURCE=2 (which are omitted with DEBUG=Y). This is the offending call chain: print_counter_aggr() printout(config, -1, 0, ...) with 2nd parm id set to -1 aggr_printout(config, x, id --> -1, ...) which leads to this code: case AGGR_NONE: if (evsel->percore && !config->percore_show_thread) { .... } else { fprintf(config->output, "CPU%*d%s", config->csv_output ? 0 : -7, evsel__cpus(evsel)->map[id], ^^ id is -1 !!!! config->csv_sep); } This is a compiler inlining issue which is detected on s390 but not on other plattforms. Output before: # make util/stat-display.o ..... util/stat-display.c: In function ‘perf_evlist__print_counters’: util/stat-display.c:121:4: error: array subscript -1 is below array bounds of ‘int[]’ [-Werror=array-bounds] 121 | fprintf(config->output, "CPU%*d%s", | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 122 | config->csv_output ? 0 : -7, | ~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 123 | evsel__cpus(evsel)->map[id], | ~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 124 | config->csv_sep); | ~~~~~~~~~~~~~~~~ In file included from util/evsel.h:13, from util/evlist.h:13, from util/stat-display.c:9: /root/linux/tools/lib/perf/include/internal/cpumap.h:10:7: note: while referencing ‘map’ 10 | int map[]; | ^~~ cc1: all warnings being treated as errors mv: cannot stat 'util/.stat-display.o.tmp': No such file or directory make[3]: *** [/root/linux/tools/build/Makefile.build:97: util/stat-display.o] Error 1 make[2]: *** [Makefile.perf:716: util/stat-display.o] Error 2 make[1]: *** [Makefile.perf:231: sub-make] Error 2 make: *** [Makefile:110: util/stat-display.o] Error 2 [root@t35lp46 perf]# Output after: # make util/stat-display.o ..... CC util/stat-display.o [root@t35lp46 perf]# Committer notes: Removed the removal of {} enclosing the multiline else block, as pointed out by Jiri Olsa. Suggested-by: Jiri Olsa <[email protected]> Signed-off-by: Thomas Richter <[email protected]> Acked-by: Jiri Olsa <[email protected]> Cc: Heiko Carstens <[email protected]> Cc: Sumanth Korikkar <[email protected]> Cc: Sven Schnelle <[email protected]> Cc: Vasily Gorbik <[email protected]> Link: http://lore.kernel.org/lkml/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
2020-09-01perf test: Set NULL sentinel in pmu_events table in "Parse and process ↵Thomas Richter1-0/+3
metrics" test Linux 5.9 introduced perf test case "Parse and process metrics" and on s390 this test case always dumps core: [root@t35lp67 perf]# ./perf test -vvvv -F 67 67: Parse and process metrics : --- start --- metric expr inst_retired.any / cpu_clk_unhalted.thread for IPC parsing metric: inst_retired.any / cpu_clk_unhalted.thread Segmentation fault (core dumped) [root@t35lp67 perf]# I debugged this core dump and gdb shows this call chain: (gdb) where #0 0x000003ffabc3192a in __strnlen_c_1 () from /lib64/libc.so.6 #1 0x000003ffabc293de in strcasestr () from /lib64/libc.so.6 #2 0x0000000001102ba2 in match_metric(list=0x1e6ea20 "inst_retired.any", n=<optimized out>) at util/metricgroup.c:368 #3 find_metric (map=<optimized out>, map=<optimized out>, metric=0x1e6ea20 "inst_retired.any") at util/metricgroup.c:765 #4 __resolve_metric (ids=0x0, map=<optimized out>, metric_list=0x0, metric_no_group=<optimized out>, m=<optimized out>) at util/metricgroup.c:844 #5 resolve_metric (ids=0x0, map=0x0, metric_list=0x0, metric_no_group=<optimized out>) at util/metricgroup.c:881 #6 metricgroup__add_metric (metric=<optimized out>, metric_no_group=metric_no_group@entry=false, events=<optimized out>, events@entry=0x3ffd84fb878, metric_list=0x0, metric_list@entry=0x3ffd84fb868, map=0x0) at util/metricgroup.c:943 #7 0x00000000011034ae in metricgroup__add_metric_list (map=0x13f9828 <map>, metric_list=0x3ffd84fb868, events=0x3ffd84fb878, metric_no_group=<optimized out>, list=<optimized out>) at util/metricgroup.c:988 #8 parse_groups (perf_evlist=perf_evlist@entry=0x1e70260, str=str@entry=0x12f34b2 "IPC", metric_no_group=<optimized out>, metric_no_merge=<optimized out>, fake_pmu=fake_pmu@entry=0x1462f18 <perf_pmu.fake>, metric_events=0x3ffd84fba58, map=0x1) at util/metricgroup.c:1040 #9 0x0000000001103eb2 in metricgroup__parse_groups_test( evlist=evlist@entry=0x1e70260, map=map@entry=0x13f9828 <map>, str=str@entry=0x12f34b2 "IPC", metric_no_group=metric_no_group@entry=false, metric_no_merge=metric_no_merge@entry=false, metric_events=0x3ffd84fba58) at util/metricgroup.c:1082 #10 0x00000000010c84d8 in __compute_metric (ratio2=0x0, name2=0x0, ratio1=<synthetic pointer>, name1=0x12f34b2 "IPC", vals=0x3ffd84fbad8, name=0x12f34b2 "IPC") at tests/parse-metric.c:159 #11 compute_metric (ratio=<synthetic pointer>, vals=0x3ffd84fbad8, name=0x12f34b2 "IPC") at tests/parse-metric.c:189 #12 test_ipc () at tests/parse-metric.c:208 ..... ..... omitted many more lines This test case was added with commit 218ca91df477 ("perf tests: Add parse metric test for frontend metric"). When I compile with make DEBUG=y it works fine and I do not get a core dump. It turned out that the above listed function call chain worked on a struct pmu_event array which requires a trailing element with zeroes which was missing. The marco map_for_each_event() loops over that array tests for members metric_expr/metric_name/metric_group being non-NULL. Adding this element fixes the issue. Output after: [root@t35lp46 perf]# ./perf test 67 67: Parse and process metrics : Ok [root@t35lp46 perf]# Committer notes: As Ian remarks, this is not s390 specific: <quote Ian> This also shows up with address sanitizer on all architectures (perhaps change the patch title) and perhaps add a "Fixes: <commit>" tag. ================================================================= ==4718==ERROR: AddressSanitizer: global-buffer-overflow on address 0x55c93b4d59e8 at pc 0x55c93a1541e2 bp 0x7ffd24327c60 sp 0x7ffd24327c58 READ of size 8 at 0x55c93b4d59e8 thread T0 #0 0x55c93a1541e1 in find_metric tools/perf/util/metricgroup.c:764:2 #1 0x55c93a153e6c in __resolve_metric tools/perf/util/metricgroup.c:844:9 #2 0x55c93a152f18 in resolve_metric tools/perf/util/metricgroup.c:881:9 #3 0x55c93a1528db in metricgroup__add_metric tools/perf/util/metricgroup.c:943:9 #4 0x55c93a151996 in metricgroup__add_metric_list tools/perf/util/metricgroup.c:988:9 #5 0x55c93a1511b9 in parse_groups tools/perf/util/metricgroup.c:1040:8 #6 0x55c93a1513e1 in metricgroup__parse_groups_test tools/perf/util/metricgroup.c:1082:9 #7 0x55c93a0108ae in __compute_metric tools/perf/tests/parse-metric.c:159:8 #8 0x55c93a010744 in compute_metric tools/perf/tests/parse-metric.c:189:9 #9 0x55c93a00f5ee in test_ipc tools/perf/tests/parse-metric.c:208:2 #10 0x55c93a00f1e8 in test__parse_metric tools/perf/tests/parse-metric.c:345:2 #11 0x55c939fd7202 in run_test tools/perf/tests/builtin-test.c:410:9 #12 0x55c939fd6736 in test_and_print tools/perf/tests/builtin-test.c:440:9 #13 0x55c939fd58c3 in __cmd_test tools/perf/tests/builtin-test.c:661:4 #14 0x55c939fd4e02 in cmd_test tools/perf/tests/builtin-test.c:807:9 #15 0x55c939e4763d in run_builtin tools/perf/perf.c:313:11 #16 0x55c939e46475 in handle_internal_command tools/perf/perf.c:365:8 #17 0x55c939e4737e in run_argv tools/perf/perf.c:409:2 #18 0x55c939e45f7e in main tools/perf/perf.c:539:3 0x55c93b4d59e8 is located 0 bytes to the right of global variable 'pme_test' defined in 'tools/perf/tests/parse-metric.c:17:25' (0x55c93b4d54a0) of size 1352 SUMMARY: AddressSanitizer: global-buffer-overflow tools/perf/util/metricgroup.c:764:2 in find_metric Shadow bytes around the buggy address: 0x0ab9a7692ae0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0ab9a7692af0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0ab9a7692b00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0ab9a7692b10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0ab9a7692b20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 =>0x0ab9a7692b30: 00 00 00 00 00 00 00 00 00 00 00 00 00[f9]f9 f9 0x0ab9a7692b40: f9 f9 f9 f9 f9 f9 f9 f9 f9 f9 f9 f9 f9 f9 f9 f9 0x0ab9a7692b50: f9 f9 f9 f9 f9 f9 f9 f9 f9 f9 f9 f9 f9 f9 f9 f9 0x0ab9a7692b60: f9 f9 f9 f9 f9 f9 f9 f9 00 00 00 00 00 00 00 00 0x0ab9a7692b70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0ab9a7692b80: f9 f9 f9 f9 f9 f9 f9 f9 f9 f9 f9 f9 f9 f9 f9 f9 Shadow byte legend (one shadow byte represents 8 application bytes): Addressable: 00 Partially addressable: 01 02 03 04 05 06 07 Heap left redzone: fa Freed heap region: fd Stack left redzone: f1 Stack mid redzone: f2 Stack right redzone: f3 Stack after return: f5 Stack use after scope: f8 Global redzone: f9 Global init order: f6 Poisoned by user: f7 Container overflow: fc Array cookie: ac Intra object redzone: bb ASan internal: fe Left alloca redzone: ca Right alloca redzone: cb Shadow gap: cc </quote> I'm also adding the missing "Fixes" tag and setting just .name to NULL, as doing it that way is more compact (the compiler will zero out everything else) and the table iterators look for .name being NULL as the sentinel marking the end of the table. Fixes: 0a507af9c681ac2a ("perf tests: Add parse metric test for ipc metric") Signed-off-by: Thomas Richter <[email protected]> Reviewed-by: Sumanth Korikkar <[email protected]> Acked-by: Ian Rogers <[email protected]> Cc: Heiko Carstens <[email protected]> Cc: Jiri Olsa <[email protected]> Cc: Namhyung Kim <[email protected]> Cc: Sven Schnelle <[email protected]> Cc: Vasily Gorbik <[email protected]> Link: http://lore.kernel.org/lkml/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
2020-09-01perf parse-events: Set exclude_guest=1 for user-space countingJin Yao2-2/+5
Currently if we run 'perf record -e cycles:u', exclude_guest=0. But it doesn't make sense in most cases that we request for user-space counting but we also get the guest report. Of course, we also need to consider 'perf kvm' usage case that authorized perf users on the host may only want to count guest user space events. For example, # perf kvm --guest record -e cycles:u When we have 'exclude_guest=1' for 'perf kvm' usage, we may get nothing from guest events. To keep perf semantics consistent and clear, this patch sets exclude_guest=1 for user-space counting but except for 'perf kvm' usage. Before: perf record -e cycles:u ./div perf evlist -v cycles:u: ..., exclude_kernel: 1, exclude_hv: 1, ... After: perf record -e cycles:u ./div perf evlist -v cycles:u: ..., exclude_kernel: 1, exclude_hv: 1, exclude_guest: 1, ... Before: perf kvm --guest record -e cycles:u -vvv perf_event_attr: size 120 { sample_period, sample_freq } 4000 sample_type IP|TID|TIME|ID|CPU|PERIOD read_format ID disabled 1 inherit 1 exclude_kernel 1 exclude_hv 1 freq 1 sample_id_all 1 After: perf kvm --guest record -e cycles:u -vvv perf_event_attr: size 120 { sample_period, sample_freq } 4000 sample_type IP|TID|TIME|ID|CPU|PERIOD read_format ID disabled 1 inherit 1 exclude_kernel 1 exclude_hv 1 freq 1 sample_id_all 1 For Before/After, exclude_guest are both 0 for perf kvm usage. perf test 6 6: Parse event definition strings : Ok Signed-off-by: Jin Yao <[email protected]> Tested-by: Like Xu <[email protected]> Cc: Alexander Shishkin <[email protected]> Cc: Andi Kleen <[email protected]> Cc: Jin Yao <[email protected]> Cc: Jiri Olsa <[email protected]> Cc: Kan Liang <[email protected]> Cc: Peter Zijlstra <[email protected]> Link: http://lore.kernel.org/lkml/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
2020-09-01perf record: Correct the help info of option "--no-bpf-event"Wei Li1-1/+1
The help info of option "--no-bpf-event" is wrongly described as "record bpf events", correct it. Committer testing: $ perf record -h bpf Usage: perf record [<options>] [<command>] or: perf record [<options>] -- <command> [<options>] --clang-opt <clang options> options passed to clang when compiling BPF scriptlets --clang-path <clang path> clang binary to use for compiling BPF scriptlets --no-bpf-event do not record bpf events $ Fixes: 71184c6ab7e6 ("perf record: Replace option --bpf-event with --no-bpf-event") Signed-off-by: Wei Li <[email protected]> Acked-by: Song Liu <[email protected]> Tested-by: Arnaldo Carvalho de Melo <[email protected]> Cc: Alexander Shishkin <[email protected]> Cc: Hanjun Guo <[email protected]> Cc: Jiri Olsa <[email protected]> Cc: Li Bin <[email protected]> Cc: Mark Rutland <[email protected]> Cc: Namhyung Kim <[email protected]> Link: http://lore.kernel.org/lkml/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
2020-09-01perf tools: Use %zd for size_t printf formats on 32-bitChris Wilson2-2/+2
A couple of trivial fixes for using %zd for size_t in the code supporting the ZSTD compression library. Signed-off-by: Chris Wilson <[email protected]> Acked-by: Jiri Olsa <[email protected]> Cc: Adrian Hunter <[email protected]> Cc: Alexey Budankov <[email protected]> Cc: Namhyung Kim <[email protected]> Cc: Peter Zijlstra <[email protected]> Link: http://lore.kernel.org/lkml/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
2020-09-01block: fix locking in bdev_del_partitionChristoph Hellwig1-14/+13
We need to hold the whole device bd_mutex to protect against other thread concurrently deleting out partition before we get to it, and thus causing a use after free. Fixes: cddae808aeb7 ("block: pass a hd_struct to delete_partition") Reported-by: [email protected] Signed-off-by: Christoph Hellwig <[email protected]> Signed-off-by: Jens Axboe <[email protected]>
2020-09-01block: release disk reference in hd_struct_free_workMing Lei1-1/+9
Commit e8c7d14ac6c3 ("block: revert back to synchronous request_queue removal") stops to release request queue from wq context because that commit supposed all blk_put_queue() is called in context which is allowed to sleep. However, this assumption isn't true because we release disk's reference in partition's percpu_ref's ->release() which doesn't allow to sleep, because the ->release() is run via call_rcu(). Fixes this issue by moving put disk reference into hd_struct_free_work() Fixes: e8c7d14ac6c3 ("block: revert back to synchronous request_queue removal") Reported-by: Ilya Dryomov <[email protected]> Signed-off-by: Ming Lei <[email protected]> Tested-by: Ilya Dryomov <[email protected]> Reviewed-by: Christoph Hellwig <[email protected]> Cc: Luis Chamberlain <[email protected]> Cc: Christoph Hellwig <[email protected]> Cc: Bart Van Assche <[email protected]> Signed-off-by: Jens Axboe <[email protected]>
2020-09-01io_uring: fix removing the wrong file in __io_sqe_files_update()Jiufei Xue1-1/+1
Index here is already the position of the file in fixed_file_table, we should not use io_file_from_index() again to get it. Otherwise, the wrong file which still in use may be released unexpectedly. Cc: [email protected] # v5.6 Fixes: 05f3fb3c5397 ("io_uring: avoid ring quiesce for fixed file set unregister and update") Signed-off-by: Jiufei Xue <[email protected]> Signed-off-by: Jens Axboe <[email protected]>
2020-09-01block: ensure bdi->io_pages is always initializedJens Axboe1-0/+1
If a driver leaves the limit settings as the defaults, then we don't initialize bdi->io_pages. This means that file systems may need to work around bdi->io_pages == 0, which is somewhat messy. Initialize the default value just like we do for ->ra_pages. Cc: [email protected] Fixes: 9491ae4aade6 ("mm: don't cap request size based on read-ahead setting") Reported-by: OGAWA Hirofumi <[email protected]> Reviewed-by: Christoph Hellwig <[email protected]> Signed-off-by: Jens Axboe <[email protected]>
2020-09-01ALSA: pcm: oss: Remove superfluous WARN_ON() for mulaw sanity checkTakashi Iwai1-2/+2
The PCM OSS mulaw plugin has a check of the format of the counter part whether it's a linear format. The check is with snd_BUG_ON() that emits WARN_ON() when the debug config is set, and it confuses syzkaller as if it were a serious issue. Let's drop snd_BUG_ON() for avoiding that. While we're at it, correct the error code to a more suitable, EINVAL. Reported-by: [email protected] Cc: <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Takashi Iwai <[email protected]>
2020-09-01MIPS: perf: Fix wrong check condition of Loongson event IDsTiezhu Yang1-2/+2
According to the user's manual chapter 8.2.1 of Loongson 3A2000 CPU [1] and 3A3000 CPU [2], we should take some event IDs such as 274, 358, 359 and 360 as valid in the check condition, otherwise they are recognized as "not supported", fix it. [1] http://www.loongson.cn/uploadfile/cpu/3A2000/Loongson3A2000_user2.pdf [2] http://www.loongson.cn/uploadfile/cpu/3A3000/Loongson3A3000_3B3000user2.pdf Fixes: e9dfbaaeef1c ("MIPS: perf: Add hardware perf events support for new Loongson-3") Signed-off-by: Tiezhu Yang <[email protected]> Acked-by: Huang Pei <[email protected]> Signed-off-by: Thomas Bogendoerfer <[email protected]>
2020-09-01clang-format: Update with the latest for_each macro listMiguel Ojeda1-0/+12
Re-run the shell fragment that generated the original list. Signed-off-by: Miguel Ojeda <[email protected]>
2020-09-01HID: core: Sanitize event code and type when mapping inputMarc Zyngier3-13/+35
When calling into hid_map_usage(), the passed event code is blindly stored as is, even if it doesn't fit in the associated bitmap. This event code can come from a variety of sources, including devices masquerading as input devices, only a bit more "programmable". Instead of taking the event code at face value, check that it actually fits the corresponding bitmap, and if it doesn't: - spit out a warning so that we know which device is acting up - NULLify the bitmap pointer so that we catch unexpected uses Code paths that can make use of untrusted inputs can now check that the mapping was indeed correct and bail out if not. Cc: [email protected] Signed-off-by: Marc Zyngier <[email protected]> Signed-off-by: Benjamin Tissoires <[email protected]>
2020-09-01HID: core: Correctly handle ReportSize being zeroMarc Zyngier1-2/+13
It appears that a ReportSize value of zero is legal, even if a bit non-sensical. Most of the HID code seems to handle that gracefully, except when computing the total size in bytes. When fed as input to memset, this leads to some funky outcomes. Detect the corner case and correctly compute the size. Cc: [email protected] Signed-off-by: Marc Zyngier <[email protected]> Signed-off-by: Benjamin Tissoires <[email protected]>
2020-09-01HID: elan: Fix memleak in elan_input_configuredDinghao Liu1-0/+2
When input_mt_init_slots() fails, input should be freed to prevent memleak. When input_register_device() fails, we should call input_mt_destroy_slots() to free memory allocated by input_mt_init_slots(). Signed-off-by: Dinghao Liu <[email protected]> Signed-off-by: Jiri Kosina <[email protected]>
2020-08-31scsi: lpfc: Update lpfc version to 12.8.0.4James Smart1-1/+1
Update lpfc version to 12.8.0.4 Link: https://lore.kernel.org/r/[email protected] Co-developed-by: Dick Kennedy <[email protected]> Signed-off-by: Dick Kennedy <[email protected]> Signed-off-by: James Smart <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2020-08-31scsi: lpfc: Extend the RDF FPIN Registration descriptor for additional eventsJames Smart2-1/+4
Currently the driver registers for Link Integrity events only. This patch adds registration for the following FPIN types: - Delivery Notifications - Congestion Notification - Peer Congestion Notification Link: https://lore.kernel.org/r/[email protected] Co-developed-by: Dick Kennedy <[email protected]> Signed-off-by: Dick Kennedy <[email protected]> Signed-off-by: James Smart <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2020-08-31scsi: lpfc: Fix FLOGI/PLOGI receive race condition in pt2pt discoveryJames Smart1-1/+3
The driver is unable to successfully login with remote device. During pt2pt login, the driver completes its FLOGI request with the remote device having WWN precedence. The remote device issues its own (delayed) FLOGI after accepting the driver's and, upon transmitting the FLOGI, immediately recognizes it has already processed the driver's FLOGI thus it transitions to sending a PLOGI before waiting for an ACC to its FLOGI. In the driver, the FLOGI is received and an ACC sent, followed by the PLOGI being received and an ACC sent. The issue is that the PLOGI reception occurs before the response from the adapter from the FLOGI ACC is received. Processing of the PLOGI sets state flags to perform the REG_RPI mailbox command and proceed with the rest of discovery on the port. The same completion routine used by both FLOGI and PLOGI is generic in nature. One of the things it does is clear flags, and those flags happen to drive the rest of discovery. So what happened was the PLOGI processing set the flags, the FLOGI ACC completion cleared them, thus when the PLOGI ACC completes it doesn't see the flags and stops. Fix by modifying the generic completion routine to not clear the rest of discovery flag (NLP_ACC_REGLOGIN) unless the completion is also associated with performing a mailbox command as part of its handling. For things such as FLOGI ACC, there isn't a subsequent action to perform with the adapter, thus there is no mailbox cmd ptr. PLOGI ACC though will perform REG_RPI upon completion, thus there is a mailbox cmd ptr. Link: https://lore.kernel.org/r/[email protected] Co-developed-by: Dick Kennedy <[email protected]> Signed-off-by: Dick Kennedy <[email protected]> Signed-off-by: James Smart <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2020-08-31scsi: lpfc: Fix setting IRQ affinity with an empty CPU maskJames Smart1-1/+0
Some systems are reporting the following log message during driver unload or system shutdown: ics_rtas_set_affinity: No online cpus in the mask A prior commit introduced the writing of an empty affinity mask in calls to irq_set_affinity_hint() when disabling interrupts or when there are no remaining online CPUs to service an eq interrupt. At least some ppc64 systems are checking whether affinity masks are empty or not. Do not call irq_set_affinity_hint() with an empty CPU mask. Fixes: dcaa21367938 ("scsi: lpfc: Change default IRQ model on AMD architectures") Link: https://lore.kernel.org/r/[email protected] Cc: <[email protected]> # v5.5+ Co-developed-by: Dick Kennedy <[email protected]> Signed-off-by: Dick Kennedy <[email protected]> Signed-off-by: James Smart <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2020-08-31scsi: qla2xxx: Fix regression on sparc64René Rebe2-4/+4
Commit 98aee70d19a7 ("qla2xxx: Add endianizer to max_payload_size modifier.") in 2014 broke qla2xxx on sparc64, e.g. as in the Sun Blade 1000 / 2000. Unbreak by partial revert to fix endianness in nvram firmware default initialization. Also mark the second frame_payload_size in nvram_t __le16 to avoid new sparse warnings. Link: https://lore.kernel.org/r/[email protected] Fixes: 98aee70d19a7 ("qla2xxx: Add endianizer to max_payload_size modifier.") Reviewed-by: Himanshu Madhani <[email protected]> Reviewed-by: Bart Van Assche <[email protected]> Acked-by: Arun Easi <[email protected]> Signed-off-by: René Rebe <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2020-08-31scsi: libfc: Fix for double free()Javed Hasan1-2/+0
Fix for '&fp->skb' double free. Link: https://lore.kernel.org/r/[email protected] Reported-by: Dan Carpenter <[email protected]> Signed-off-by: Javed Hasan <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2020-08-31scsi: pm8001: Fix memleak in pm8001_exec_internal_task_abortDinghao Liu1-1/+1
When pm8001_tag_alloc() fails, task should be freed just like it is done in the subsequent error paths. Link: https://lore.kernel.org/r/[email protected] Acked-by: Jack Wang <[email protected]> Signed-off-by: Dinghao Liu <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2020-08-31net: ethernet: ti: am65-cpsw: fix rmii 100Mbit link modeGrygorii Strashko1-0/+2
In RMII link mode it's required to set bit 15 IFCTL_A in MAC_SL MAC_CONTROL register to enable support for 100Mbit link speed. Fixes: 93a76530316a ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver") Signed-off-by: Grygorii Strashko <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-08-31Merge tag 'docs-5.9-3' of git://git.lwn.net/linuxLinus Torvalds16-55/+57
Pull documentation fixes from Jonathan Corbet: "A handful of documentation fixes for 5.9" * tag 'docs-5.9-3' of git://git.lwn.net/linux: Documentation: laptops: thinkpad-acpi: fix underline length build warning Documentation: fix typo for abituguru documentation docs: Fix function name trailing double-()s devices.txt: fix typo of "ubd" as "udb" Documentation: add riscv entry in list of existing profiles MAINTAINERS: mention documentation maintainer entry profile Fpga: Documentation: Replace deprecated :c:func: Usage IIO: Documentation: Replace deprecated :c:func: Usage Documentation/locking/locktypes: fix local_locks documentation
2020-08-31cxgb4: fix thermal zone device registrationPotnuri Bharat Teja1-2/+6
When multiple adapters are present in the system, pci hot-removing second adapter leads to the following warning as both the adapters registered thermal zone device with same thermal zone name/type. Therefore, use unique thermal zone name during thermal zone device initialization. Also mark thermal zone dev NULL once unregistered. [ 414.370143] ------------[ cut here ]------------ [ 414.370944] sysfs group 'power' not found for kobject 'hwmon0' [ 414.371747] WARNING: CPU: 9 PID: 2661 at fs/sysfs/group.c:281 sysfs_remove_group+0x76/0x80 [ 414.382550] CPU: 9 PID: 2661 Comm: bash Not tainted 5.8.0-rc6+ #33 [ 414.383593] Hardware name: Supermicro X10SRA-F/X10SRA-F, BIOS 2.0a 06/23/2016 [ 414.384669] RIP: 0010:sysfs_remove_group+0x76/0x80 [ 414.385738] Code: 48 89 df 5b 5d 41 5c e9 d8 b5 ff ff 48 89 df e8 60 b0 ff ff eb cb 49 8b 14 24 48 8b 75 00 48 c7 c7 90 ae 13 bb e8 6a 27 d0 ff <0f> 0b 5b 5d 41 5c c3 0f 1f 00 0f 1f 44 00 00 48 85 f6 74 31 41 54 [ 414.388404] RSP: 0018:ffffa22bc080fcb0 EFLAGS: 00010286 [ 414.389638] RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000 [ 414.390829] RDX: 0000000000000001 RSI: ffff8ee2de3e9510 RDI: ffff8ee2de3e9510 [ 414.392064] RBP: ffffffffbaef2ee0 R08: 0000000000000000 R09: 0000000000000000 [ 414.393224] R10: 0000000000000000 R11: 000000002b30006c R12: ffff8ee260720008 [ 414.394388] R13: ffff8ee25e0a40e8 R14: ffffa22bc080ff08 R15: ffff8ee2c3be5020 [ 414.395661] FS: 00007fd2a7171740(0000) GS:ffff8ee2de200000(0000) knlGS:0000000000000000 [ 414.396825] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 414.398011] CR2: 00007f178ffe5020 CR3: 000000084c5cc003 CR4: 00000000003606e0 [ 414.399172] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 414.400352] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 414.401473] Call Trace: [ 414.402685] device_del+0x89/0x400 [ 414.403819] device_unregister+0x16/0x60 [ 414.405024] hwmon_device_unregister+0x44/0xa0 [ 414.406112] thermal_remove_hwmon_sysfs+0x196/0x200 [ 414.407256] thermal_zone_device_unregister+0x1b5/0x1f0 [ 414.408415] cxgb4_thermal_remove+0x3c/0x4f [cxgb4] [ 414.409668] remove_one+0x212/0x290 [cxgb4] [ 414.410875] pci_device_remove+0x36/0xb0 [ 414.412004] device_release_driver_internal+0xe2/0x1c0 [ 414.413276] pci_stop_bus_device+0x64/0x90 [ 414.414433] pci_stop_and_remove_bus_device_locked+0x16/0x30 [ 414.415609] remove_store+0x75/0x90 [ 414.416790] kernfs_fop_write+0x114/0x1b0 [ 414.417930] vfs_write+0xcf/0x210 [ 414.419059] ksys_write+0xa7/0xe0 [ 414.420120] do_syscall_64+0x4c/0xa0 [ 414.421278] entry_SYSCALL_64_after_hwframe+0x44/0xa9 [ 414.422335] RIP: 0033:0x7fd2a686afd0 [ 414.423396] Code: Bad RIP value. [ 414.424549] RSP: 002b:00007fffc1446148 EFLAGS: 00000246 ORIG_RAX: 0000000000000001 [ 414.425638] RAX: ffffffffffffffda RBX: 0000000000000002 RCX: 00007fd2a686afd0 [ 414.426830] RDX: 0000000000000002 RSI: 00007fd2a7196000 RDI: 0000000000000001 [ 414.427927] RBP: 00007fd2a7196000 R08: 000000000000000a R09: 00007fd2a7171740 [ 414.428923] R10: 00007fd2a7171740 R11: 0000000000000246 R12: 00007fd2a6b43400 [ 414.430082] R13: 0000000000000002 R14: 0000000000000001 R15: 0000000000000000 [ 414.431027] irq event stamp: 76300 [ 414.435678] ---[ end trace 13865acb4d5ab00f ]--- Fixes: b18719157762 ("cxgb4: Add thermal zone support") Signed-off-by: Potnuri Bharat Teja <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-08-31drivers/net/wan/hdlc_cisco: Add hard_header_lenXie He1-0/+1
This driver didn't set hard_header_len. This patch sets hard_header_len for it according to its header_ops->create function. This driver's header_ops->create function (cisco_hard_header) creates a header of (struct hdlc_header), so hard_header_len should be set to sizeof(struct hdlc_header). Cc: Martin Schiller <[email protected]> Signed-off-by: Xie He <[email protected]> Acked-by: Krzysztof Halasa <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-08-31ionic: fix txrx work accountingShannon Nelson1-10/+3
Take the tx accounting out of the work_done calculation to prevent a possible duplicate napi_schedule call when under high Tx stress but low Rx traffic. Fixes: b14e4e95f9ec ("ionic: tx separate servicing") Signed-off-by: Shannon Nelson <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-08-31Merge tag 'mmc-v5.9-rc1' of ↵Linus Torvalds11-43/+203
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc Pull MMC fixes from Ulf Hansson: - Fix HS400 tuning for ACPI ID AMDI0040 - Fix reset of CQHCI for Intel GLK-based controllers - Use correct timeout clock for Tegra186/194/210 - Fix eMMC mounting on mt7622/Bpi-64 * tag 'mmc-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: sdhci: tegra: Add missing TMCLK for data timeout arm64: tegra: Add missing timeout clock to Tegra194 SDMMC nodes arm64: tegra: Add missing timeout clock to Tegra186 SDMMC nodes arm64: tegra: Add missing timeout clock to Tegra210 SDMMC dt-bindings: mmc: tegra: Add tmclk for Tegra210 and later sdhci: tegra: Remove SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK for Tegra186 sdhci: tegra: Remove SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK for Tegra210 arm64: dts: mt7622: add reset node for mmc device dt-bindings: mmc: Add missing description for clk_in/out_sd1 mmc: mediatek: add optional module reset property mmc: dt-bindings: Add resets/reset-names for Mediatek MMC bindings mmc: sdhci-pci: Fix SDHCI_RESET_ALL for CQHCI for Intel GLK-based controllers mmc: sdhci-acpi: Fix HS400 tuning for AMDI0040
2020-08-31Merge git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nfDavid S. Miller12-91/+92
Pablo Neira Ayuso says: ==================== Netfilter fixes for net The following patchset contains Netfilter fixes for net: 1) Do not delete clash entries on reply, let them expire instead, from Florian Westphal. 2) Do not report EAGAIN to nfnetlink, otherwise this enters a busy loop. Update nfnetlink_unicast() to translate EAGAIN to ENOBUFS. 3) Remove repeated words in code comments, from Randy Dunlap. 4) Several patches for the flowtable selftests, from Fabian Frederick. ==================== Signed-off-by: David S. Miller <[email protected]>
2020-08-31microblaze: fix min_low_pfn/max_low_pfn build errorsRandy Dunlap1-0/+3
Fix min_low_pfn/max_low_pfn build errors for arch/microblaze/: (e.g.) ERROR: "min_low_pfn" [drivers/rpmsg/virtio_rpmsg_bus.ko] undefined! ERROR: "min_low_pfn" [drivers/hwtracing/intel_th/intel_th_msu_sink.ko] undefined! ERROR: "min_low_pfn" [drivers/hwtracing/intel_th/intel_th_msu.ko] undefined! ERROR: "min_low_pfn" [drivers/mmc/core/mmc_core.ko] undefined! ERROR: "min_low_pfn" [drivers/md/dm-crypt.ko] undefined! ERROR: "min_low_pfn" [drivers/net/wireless/ath/ath6kl/ath6kl_sdio.ko] undefined! ERROR: "min_low_pfn" [crypto/tcrypt.ko] undefined! ERROR: "min_low_pfn" [crypto/asymmetric_keys/asym_tpm.ko] undefined! Mike had/has an alternate patch for Microblaze: https://lore.kernel.org/lkml/[email protected]/ David suggested just exporting min_low_pfn & max_low_pfn in mm/memblock.c: https://lore.kernel.org/lkml/alpine.DEB.2.22.394.2006291911220.1118534@chino.kir.corp.google.com/ Reported-by: kernel test robot <[email protected]> Signed-off-by: Randy Dunlap <[email protected]> Acked-by: Michal Simek <[email protected]> Acked-by: David Rientjes <[email protected]> Cc: [email protected] Cc: Andrew Morton <[email protected]> Cc: David Rientjes <[email protected]> Cc: Mike Rapoport <[email protected]> Cc: Michal Simek <[email protected]> Cc: Michal Simek <[email protected]> Signed-off-by: Mike Rapoport <[email protected]>
2020-08-31Documentation/llvm: Improve formatting of commands, variables, and argumentsNathan Chancellor1-13/+13
While reviewing a separate patch, I noticed that the formatting of the commands, variables, and arguments was not in a monospaced font like the rest of the Kbuild documentation (see kbuild/kconfig.rst for an example). This is due to a lack of "::" before indented command blocks and single backticks instead of double backticks for inline formatting. Add those so that the document looks nicer in an HTML format, while not ruining the look in plain text. As a result of this, we can remove the escaped backslashes in the last code block and move them to single backslashes. Signed-off-by: Nathan Chancellor <[email protected]> Reviewed-by: Nick Desaulniers <[email protected]> Signed-off-by: Masahiro Yamada <[email protected]>
2020-08-31affs: fix basic permission bits to actually workMax Staudt3-7/+62
The basic permission bits (protection bits in AmigaOS) have been broken in Linux' AFFS - it would only set bits, but never delete them. Also, contrary to the documentation, the Archived bit was not handled. Let's fix this for good, and set the bits such that Linux and classic AmigaOS can coexist in the most peaceful manner. Also, update the documentation to represent the current state of things. Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Cc: [email protected] Signed-off-by: Max Staudt <[email protected]> Signed-off-by: David Sterba <[email protected]>
2020-08-31opp: Don't drop reference for an OPP table that was never parsedViresh Kumar2-7/+17
dev_pm_opp_remove_table() should drop a reference to the OPP table only if the DT OPP table was parsed earlier with a call to dev_pm_opp_of_add_table() earlier. Else it may end up dropping the reference to the OPP table, which was added as a result of other calls like dev_pm_opp_set_clkname(). And would hence result in undesirable behavior later on when caller would try to free the resource again. Fixes: 03758d60265c ("opp: Replace list_kref with a local counter") Reported-by: Naresh Kamboju <[email protected]> Reported-by: Anders Roxell <[email protected]> Tested-by: Naresh Kamboju <[email protected]> Signed-off-by: Viresh Kumar <[email protected]>
2020-08-31HID: microsoft: Add rumble support for the 8bitdo SN30 Pro+ controllerNicholas Miell2-0/+3
When operating in XInput mode, the 8bitdo SN30 Pro+ requires the same quirk as the official Xbox One Bluetooth controllers for rumble to function. Other controllers like the N30 Pro 2, SF30 Pro, SN30 Pro, etc. probably also need this quirk, but I do not have the hardware to test. Signed-off-by: Nicholas Miell <[email protected]> Signed-off-by: Jiri Kosina <[email protected]>
2020-08-31HID: quirks: Set INCREMENT_USAGE_ON_DUPLICATE for all Saitek X52 devicesNirenjan Krishnan2-0/+4
The Saitek X52 family of joysticks has a pair of axes that were originally (by the Windows driver) used as mouse pointer controls. The corresponding usage page is the Game Controls page, which is not recognized by the generic HID driver, and therefore, both axes get mapped to ABS_MISC. The quirk makes the second axis get mapped to ABS_MISC+1, and therefore made available separately. One Saitek X52 device is already fixed. This patch fixes the other two known devices with VID/PID 06a3:0255 and 06a3:0762. Signed-off-by: Nirenjan Krishnan <[email protected]> Signed-off-by: Jiri Kosina <[email protected]>
2020-08-30tipc: fix using smp_processor_id() in preemptibleTuong Lien1-3/+9
The 'this_cpu_ptr()' is used to obtain the AEAD key' TFM on the current CPU for encryption, however the execution can be preemptible since it's actually user-space context, so the 'using smp_processor_id() in preemptible' has been observed. We fix the issue by using the 'get/put_cpu_ptr()' API which consists of a 'preempt_disable()' instead. Fixes: fc1b6d6de220 ("tipc: introduce TIPC encryption & authentication") Acked-by: Jon Maloy <[email protected]> Signed-off-by: Tuong Lien <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-08-30Linux 5.9-rc3Linus Torvalds1-1/+1
2020-08-30Merge branch 'linus' of ↵Linus Torvalds4-13/+19
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6 Pull crypto fixes from Herbert Xu: - fix regression in af_alg that affects iwd - restore polling delay in qat - fix double free in ingenic on error path - fix potential build failure in sa2ul due to missing Kconfig dependency * 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: crypto: af_alg - Work around empty control messages without MSG_MORE crypto: sa2ul - add Kconfig selects to fix build error crypto: ingenic - Drop kfree for memory allocated with devm_kzalloc crypto: qat - add delay before polling mailbox
2020-08-30Merge tag 'x86-urgent-2020-08-30' of ↵Linus Torvalds4-13/+45
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull x86 fixes from Thomas Gleixner: "Three interrupt related fixes for X86: - Move disabling of the local APIC after invoking fixup_irqs() to ensure that interrupts which are incoming are noted in the IRR and not ignored. - Unbreak affinity setting. The rework of the entry code reused the regular exception entry code for device interrupts. The vector number is pushed into the errorcode slot on the stack which is then lifted into an argument and set to -1 because that's regs->orig_ax which is used in quite some places to check whether the entry came from a syscall. But it was overlooked that orig_ax is used in the affinity cleanup code to validate whether the interrupt has arrived on the new target. It turned out that this vector check is pointless because interrupts are never moved from one vector to another on the same CPU. That check is a historical leftover from the time where x86 supported multi-CPU affinities, but not longer needed with the now strict single CPU affinity. Famous last words ... - Add a missing check for an empty cpumask into the matrix allocator. The affinity change added a warning to catch the case where an interrupt is moved on the same CPU to a different vector. This triggers because a condition with an empty cpumask returns an assignment from the allocator as the allocator uses for_each_cpu() without checking the cpumask for being empty. The historical inconsistent for_each_cpu() behaviour of ignoring the cpumask and unconditionally claiming that CPU0 is in the mask struck again. Sigh. plus a new entry into the MAINTAINER file for the HPE/UV platform" * tag 'x86-urgent-2020-08-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: genirq/matrix: Deal with the sillyness of for_each_cpu() on UP x86/irq: Unbreak interrupt affinity setting x86/hotplug: Silence APIC only after all interrupts are migrated MAINTAINERS: Add entry for HPE Superdome Flex (UV) maintainers
2020-08-30Merge tag 'irq-urgent-2020-08-30' of ↵Linus Torvalds23-394/+534
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull irq fixes from Thomas Gleixner: "A set of fixes for interrupt chip drivers: - Revert the platform driver conversion of interrupt chip drivers as it turned out to create more problems than it solves. - Fix a trivial typo in the new module helpers which made probing reliably fail. - Small fixes in the STM32 and MIPS Ingenic drivers - The TI firmware rework which had badly managed dependencies and had to wait post rc1" * tag 'irq-urgent-2020-08-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: irqchip/ingenic: Leave parent IRQ unmasked on suspend irqchip/stm32-exti: Avoid losing interrupts due to clearing pending bits by mistake irqchip: Revert modular support for drivers using IRQCHIP_PLATFORM_DRIVER helperse irqchip: Fix probing deferal when using IRQCHIP_PLATFORM_DRIVER helpers arm64: dts: k3-am65: Update the RM resource types arm64: dts: k3-am65: ti-sci-inta/intr: Update to latest bindings arm64: dts: k3-j721e: ti-sci-inta/intr: Update to latest bindings irqchip/ti-sci-inta: Add support for INTA directly connecting to GIC irqchip/ti-sci-inta: Do not store TISCI device id in platform device id field dt-bindings: irqchip: Convert ti, sci-inta bindings to yaml dt-bindings: irqchip: ti, sci-inta: Update docs to support different parent. irqchip/ti-sci-intr: Add support for INTR being a parent to INTR dt-bindings: irqchip: Convert ti, sci-intr bindings to yaml dt-bindings: irqchip: ti, sci-intr: Update bindings to drop the usage of gic as parent firmware: ti_sci: Add support for getting resource with subtype firmware: ti_sci: Drop unused structure ti_sci_rm_type_map firmware: ti_sci: Drop the device id to resource type translation
Powered by cgit, Gruvboxed by Blaster4385.