aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2024-10-17wifi: rtlwifi: rtl8192du: Don't claim USB ID 0bda:8171Bitterblue Smith1-1/+0
This ID appears to be RTL8188SU, not RTL8192DU. This is the wrong driver for RTL8188SU. The r8712u driver from staging handles this ID. I think this ID comes from the original rtl8192du driver from Realtek. I don't know if they added it by mistake, or it was actually used for two different chips. RTL8188SU with this ID exists in the wild. RTL8192DU with this ID probably doesn't. Fixes: b5dc8873b6ff ("wifi: rtlwifi: Add rtl8192du/sw.c") Cc: [email protected] # v6.11 Closes: https://github.com/lwfinger/rtl8192du/issues/105 Signed-off-by: Bitterblue Smith <[email protected]> Acked-by: Ping-Ke Shih <[email protected]> Signed-off-by: Kalle Valo <[email protected]> Link: https://patch.msgid.link/[email protected]
2024-10-17wifi: rtw88: Fix the RX aggregation in USB 3 modeBitterblue Smith1-1/+0
RTL8822CU, RTL8822BU, and RTL8821CU don't need BIT_EN_PRE_CALC. In fact, RTL8822BU in USB 3 mode doesn't pass all the frames to the driver, resulting in much lower download speed than normal: $ iperf3 -c 192.168.0.1 -R Connecting to host 192.168.0.1, port 5201 Reverse mode, remote host 192.168.0.1 is sending [ 5] local 192.168.0.50 port 43062 connected to 192.168.0.1 port 5201 [ ID] Interval Transfer Bitrate [ 5] 0.00-1.00 sec 26.9 MBytes 225 Mbits/sec [ 5] 1.00-2.00 sec 7.50 MBytes 62.9 Mbits/sec [ 5] 2.00-3.00 sec 8.50 MBytes 71.3 Mbits/sec [ 5] 3.00-4.00 sec 8.38 MBytes 70.3 Mbits/sec [ 5] 4.00-5.00 sec 7.75 MBytes 65.0 Mbits/sec [ 5] 5.00-6.00 sec 8.00 MBytes 67.1 Mbits/sec [ 5] 6.00-7.00 sec 8.00 MBytes 67.1 Mbits/sec [ 5] 7.00-8.00 sec 7.75 MBytes 65.0 Mbits/sec [ 5] 8.00-9.00 sec 7.88 MBytes 66.1 Mbits/sec [ 5] 9.00-10.00 sec 7.88 MBytes 66.1 Mbits/sec - - - - - - - - - - - - - - - - - - - - - - - - - [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-10.02 sec 102 MBytes 85.1 Mbits/sec 224 sender [ 5] 0.00-10.00 sec 98.6 MBytes 82.7 Mbits/sec receiver Don't set BIT_EN_PRE_CALC. Then the speed is much better: % iperf3 -c 192.168.0.1 -R Connecting to host 192.168.0.1, port 5201 Reverse mode, remote host 192.168.0.1 is sending [ 5] local 192.168.0.50 port 39000 connected to 192.168.0.1 port 5201 [ ID] Interval Transfer Bitrate [ 5] 0.00-1.00 sec 52.8 MBytes 442 Mbits/sec [ 5] 1.00-2.00 sec 71.9 MBytes 603 Mbits/sec [ 5] 2.00-3.00 sec 74.8 MBytes 627 Mbits/sec [ 5] 3.00-4.00 sec 75.9 MBytes 636 Mbits/sec [ 5] 4.00-5.00 sec 76.0 MBytes 638 Mbits/sec [ 5] 5.00-6.00 sec 74.1 MBytes 622 Mbits/sec [ 5] 6.00-7.00 sec 74.0 MBytes 621 Mbits/sec [ 5] 7.00-8.00 sec 76.0 MBytes 638 Mbits/sec [ 5] 8.00-9.00 sec 74.4 MBytes 624 Mbits/sec [ 5] 9.00-10.00 sec 63.9 MBytes 536 Mbits/sec - - - - - - - - - - - - - - - - - - - - - - - - - [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-10.00 sec 717 MBytes 601 Mbits/sec 24 sender [ 5] 0.00-10.00 sec 714 MBytes 599 Mbits/sec receiver Fixes: 002a5db9a52a ("wifi: rtw88: Enable USB RX aggregation for 8822c/8822b/8821c") Signed-off-by: Bitterblue Smith <[email protected]> Acked-by: Ping-Ke Shih <[email protected]> Signed-off-by: Kalle Valo <[email protected]> Link: https://patch.msgid.link/[email protected]
2024-10-17wifi: brcm80211: BRCM_TRACING should depend on TRACINGGeert Uytterhoeven1-0/+1
When tracing is disabled, there is no point in asking the user about enabling Broadcom wireless device tracing. Fixes: f5c4f10852d42012 ("brcm80211: Allow trace support to be enabled separately from debug") Signed-off-by: Geert Uytterhoeven <[email protected]> Acked-by: Arend van Spriel <[email protected]> Signed-off-by: Kalle Valo <[email protected]> Link: https://patch.msgid.link/81a29b15eaacc1ac1fb421bdace9ac0c3385f40f.1727179742.git.geert@linux-m68k.org
2024-10-17wifi: rtw89: pci: early chips only enable 36-bit DMA on specific PCI hostsPing-Ke Shih1-7/+41
The early chips including RTL8852A, RTL8851B, RTL8852B and RTL8852BT have interoperability problems of 36-bit DMA with some PCI hosts. Rollback to 32-bit DMA by default, and only enable 36-bit DMA for tested platforms. Since all Intel platforms we have can work correctly, add the vendor ID to white list. Otherwise, list vendor/device ID of bridge we have tested. Fixes: 1fd4b3fe52ef ("wifi: rtw89: pci: support 36-bit PCI DMA address") Reported-by: Marcel Weißenbach <[email protected]> Closes: https://lore.kernel.org/linux-wireless/[email protected]/T/#m07c5694df1acb173a42e1a0bab7ac22bd231a2b8 Signed-off-by: Ping-Ke Shih <[email protected]> Tested-by: Marcel Weißenbach <[email protected]> Signed-off-by: Kalle Valo <[email protected]> Link: https://patch.msgid.link/[email protected]
2024-10-08wifi: mac80211: skip non-uploaded keys in ieee80211_iter_keysFelix Fietkau1-17/+25
Sync iterator conditions with ieee80211_iter_keys_rcu. Fixes: 830af02f24fb ("mac80211: allow driver to iterate keys") Signed-off-by: Felix Fietkau <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Johannes Berg <[email protected]>
2024-10-08wifi: radiotap: Avoid -Wflex-array-member-not-at-end warningsGustavo A. R. Silva7-28/+33
-Wflex-array-member-not-at-end was introduced in GCC-14, and we are getting ready to enable it, globally. So, in order to avoid ending up with a flexible-array member in the middle of multiple other structs, we use the `__struct_group()` helper to create a new tagged `struct ieee80211_radiotap_header_fixed`. This structure groups together all the members of the flexible `struct ieee80211_radiotap_header` except the flexible array. As a result, the array is effectively separated from the rest of the members without modifying the memory layout of the flexible structure. We then change the type of the middle struct members currently causing trouble from `struct ieee80211_radiotap_header` to `struct ieee80211_radiotap_header_fixed`. We also want to ensure that in case new members need to be added to the flexible structure, they are always included within the newly created tagged struct. For this, we use `static_assert()`. This ensures that the memory layout for both the flexible structure and the new tagged struct is the same after any changes. This approach avoids having to implement `struct ieee80211_radiotap_header_fixed` as a completely separate structure, thus preventing having to maintain two independent but basically identical structures, closing the door to potential bugs in the future. So, with these changes, fix the following warnings: drivers/net/wireless/ath/wil6210/txrx.c:309:50: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end] drivers/net/wireless/intel/ipw2x00/ipw2100.c:2521:50: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end] drivers/net/wireless/intel/ipw2x00/ipw2200.h:1146:42: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end] drivers/net/wireless/intel/ipw2x00/libipw.h:595:36: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end] drivers/net/wireless/marvell/libertas/radiotap.h:34:42: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end] drivers/net/wireless/marvell/libertas/radiotap.h:5:42: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end] drivers/net/wireless/microchip/wilc1000/mon.c:10:42: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end] drivers/net/wireless/microchip/wilc1000/mon.c:15:42: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end] drivers/net/wireless/virtual/mac80211_hwsim.c:758:42: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end] drivers/net/wireless/virtual/mac80211_hwsim.c:767:42: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end] Signed-off-by: Gustavo A. R. Silva <[email protected]> Link: https://patch.msgid.link/ZwBMtBZKcrzwU7l4@kspp Signed-off-by: Johannes Berg <[email protected]>
2024-10-08wifi: mac80211: do not pass a stopped vif to the driver in .get_txpowerFelix Fietkau1-1/+2
Avoid potentially crashing in the driver because of uninitialized private data Fixes: 5b3dc42b1b0d ("mac80211: add support for driver tx power reporting") Cc: [email protected] Signed-off-by: Felix Fietkau <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Johannes Berg <[email protected]>
2024-10-08wifi: mac80211: Convert color collision detection to wiphy workRemi Pommarel3-13/+16
Call to ieee80211_color_collision_detection_work() needs wiphy lock to be held (see lockdep assert in cfg80211_bss_color_notify()). Not locking wiphy causes the following lockdep error: WARNING: CPU: 2 PID: 42 at net/wireless/nl80211.c:19505 cfg80211_bss_color_notify+0x1a4/0x25c Modules linked in: CPU: 2 PID: 42 Comm: kworker/u8:3 Tainted: G W 6.4.0-02327-g36c6cb260481 #1048 Hardware name: Workqueue: phy1 ieee80211_color_collision_detection_work pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : cfg80211_bss_color_notify+0x1a4/0x25c lr : cfg80211_bss_color_notify+0x1a0/0x25c sp : ffff000002947d00 x29: ffff000002947d00 x28: ffff800008e1a000 x27: ffff000002bd4705 x26: ffff00000d034000 x25: ffff80000903cf40 x24: 0000000000000000 x23: ffff00000cb70720 x22: 0000000000800000 x21: ffff800008dfb008 x20: 000000000000008d x19: ffff00000d035fa8 x18: 0000000000000010 x17: 0000000000000001 x16: 000003564b1ce96a x15: 000d69696d057970 x14: 000000000000003b x13: 0000000000000001 x12: 0000000000040000 x11: 0000000000000001 x10: ffff80000978f9c0 x9 : ffff0000028d3174 x8 : ffff800008e30000 x7 : 0000000000000000 x6 : 0000000000000028 x5 : 000000000002f498 x4 : ffff00000d034a80 x3 : 0000000000800000 x2 : ffff800016143000 x1 : 0000000000000000 x0 : 0000000000000000 Call trace: cfg80211_bss_color_notify+0x1a4/0x25c ieee80211_color_collision_detection_work+0x20/0x118 process_one_work+0x294/0x554 worker_thread+0x70/0x440 kthread+0xf4/0xf8 ret_from_fork+0x10/0x20 irq event stamp: 77372 hardirqs last enabled at (77371): [<ffff800008a346fc>] _raw_spin_unlock_irq+0x2c/0x4c hardirqs last disabled at (77372): [<ffff800008a28754>] el1_dbg+0x20/0x48 softirqs last enabled at (77350): [<ffff8000089e120c>] batadv_send_outstanding_bcast_packet+0xb8/0x120 softirqs last disabled at (77348): [<ffff8000089e11d4>] batadv_send_outstanding_bcast_packet+0x80/0x120 The wiphy lock cannot be taken directly from color collision detection delayed work (ieee80211_color_collision_detection_work()) because this work is cancel_delayed_work_sync() under this wiphy lock causing a potential deadlock( see [0] for details). To fix that ieee80211_color_collision_detection_work() could be converted to a wiphy work and cancel_delayed_work_sync() can be simply replaced by wiphy_delayed_work_cancel() serving the same purpose under wiphy lock. This could potentially fix [1]. [0]: https://lore.kernel.org/linux-wireless/[email protected]/ [1]: https://lore.kernel.org/lkml/[email protected]/ Reported-by: Nicolas Escande <[email protected]> Signed-off-by: Remi Pommarel <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Johannes Berg <[email protected]>
2024-10-08wifi: cfg80211: Add wiphy_delayed_work_pending()Remi Pommarel2-0/+51
Add wiphy_delayed_work_pending() to check if any delayed work timer is pending, that can be used to be sure that wiphy_delayed_work_queue() won't postpone an already pending delayed work. Signed-off-by: Remi Pommarel <[email protected]> Link: https://patch.msgid.link/[email protected] [fix return value kernel-doc] Signed-off-by: Johannes Berg <[email protected]>
2024-10-08wifi: cfg80211: Do not create BSS entries for unsupported channelsChenming Huang1-0/+4
Currently, in cfg80211_parse_ml_elem_sta_data(), when RNR element indicates a BSS that operates in a channel that current regulatory domain doesn't support, a NULL value is returned by ieee80211_get_channel_khz() and assigned to this BSS entry's channel field. Later in cfg80211_inform_single_bss_data(), the reported BSS entry's channel will be wrongly overridden by transmitted BSS's. This could result in connection failure that when wpa_supplicant tries to select this reported BSS entry while it actually resides in an unsupported channel. Since this channel is not supported, it is reasonable to skip such entries instead of reporting wrong information. Signed-off-by: Chenming Huang <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Johannes Berg <[email protected]>
2024-10-08wifi: mac80211: Fix setting txpower with emulate_chanctxBen Greear1-0/+5
Propagate hw conf into the driver when txpower changes and driver is emulating channel contexts. Signed-off-by: Ben Greear <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Johannes Berg <[email protected]>
2024-10-08mac80211: MAC80211_MESSAGE_TRACING should depend on TRACINGGeert Uytterhoeven1-1/+1
When tracing is disabled, there is no point in asking the user about enabling tracing of all mac80211 debug messages. Fixes: 3fae0273168026ed ("mac80211: trace debug messages") Signed-off-by: Geert Uytterhoeven <[email protected]> Link: https://patch.msgid.link/85bbe38ce0df13350f45714e2dc288cc70947a19.1727179690.git.geert@linux-m68k.org Signed-off-by: Johannes Berg <[email protected]>
2024-10-08wifi: iwlegacy: Clear stale interrupts before resuming deviceVille Syrjälä1-0/+2
iwl4965 fails upon resume from hibernation on my laptop. The reason seems to be a stale interrupt which isn't being cleared out before interrupts are enabled. We end up with a race beween the resume trying to bring things back up, and the restart work (queued form the interrupt handler) trying to bring things down. Eventually the whole thing blows up. Fix the problem by clearing out any stale interrupts before interrupts get enabled during resume. Here's a debug log of the indicent: [ 12.042589] ieee80211 phy0: il_isr ISR inta 0x00000080, enabled 0xaa00008b, fh 0x00000000 [ 12.042625] ieee80211 phy0: il4965_irq_tasklet inta 0x00000080, enabled 0x00000000, fh 0x00000000 [ 12.042651] iwl4965 0000:10:00.0: RF_KILL bit toggled to enable radio. [ 12.042653] iwl4965 0000:10:00.0: On demand firmware reload [ 12.042690] ieee80211 phy0: il4965_irq_tasklet End inta 0x00000000, enabled 0xaa00008b, fh 0x00000000, flags 0x00000282 [ 12.052207] ieee80211 phy0: il4965_mac_start enter [ 12.052212] ieee80211 phy0: il_prep_station Add STA to driver ID 31: ff:ff:ff:ff:ff:ff [ 12.052244] ieee80211 phy0: il4965_set_hw_ready hardware ready [ 12.052324] ieee80211 phy0: il_apm_init Init card's basic functions [ 12.052348] ieee80211 phy0: il_apm_init L1 Enabled; Disabling L0S [ 12.055727] ieee80211 phy0: il4965_load_bsm Begin load bsm [ 12.056140] ieee80211 phy0: il4965_verify_bsm Begin verify bsm [ 12.058642] ieee80211 phy0: il4965_verify_bsm BSM bootstrap uCode image OK [ 12.058721] ieee80211 phy0: il4965_load_bsm BSM write complete, poll 1 iterations [ 12.058734] ieee80211 phy0: __il4965_up iwl4965 is coming up [ 12.058737] ieee80211 phy0: il4965_mac_start Start UP work done. [ 12.058757] ieee80211 phy0: __il4965_down iwl4965 is going down [ 12.058761] ieee80211 phy0: il_scan_cancel_timeout Scan cancel timeout [ 12.058762] ieee80211 phy0: il_do_scan_abort Not performing scan to abort [ 12.058765] ieee80211 phy0: il_clear_ucode_stations Clearing ucode stations in driver [ 12.058767] ieee80211 phy0: il_clear_ucode_stations No active stations found to be cleared [ 12.058819] ieee80211 phy0: _il_apm_stop Stop card, put in low power state [ 12.058827] ieee80211 phy0: _il_apm_stop_master stop master [ 12.058864] ieee80211 phy0: il4965_clear_free_frames 0 frames on pre-allocated heap on clear. [ 12.058869] ieee80211 phy0: Hardware restart was requested [ 16.132299] iwl4965 0000:10:00.0: START_ALIVE timeout after 4000ms. [ 16.132303] ------------[ cut here ]------------ [ 16.132304] Hardware became unavailable upon resume. This could be a software issue prior to suspend or a hardware issue. [ 16.132338] WARNING: CPU: 0 PID: 181 at net/mac80211/util.c:1826 ieee80211_reconfig+0x8f/0x14b0 [mac80211] [ 16.132390] Modules linked in: ctr ccm sch_fq_codel xt_tcpudp xt_multiport xt_state iptable_filter iptable_nat nf_nat nf_conntrack nf_defrag_ipv4 ip_tables x_tables binfmt_misc joydev mousedev btusb btrtl btintel btbcm bluetooth ecdh_generic ecc iTCO_wdt i2c_dev iwl4965 iwlegacy coretemp snd_hda_codec_analog pcspkr psmouse mac80211 snd_hda_codec_generic libarc4 sdhci_pci cqhci sha256_generic sdhci libsha256 firewire_ohci snd_hda_intel snd_intel_dspcfg mmc_core snd_hda_codec snd_hwdep firewire_core led_class iosf_mbi snd_hda_core uhci_hcd lpc_ich crc_itu_t cfg80211 ehci_pci ehci_hcd snd_pcm usbcore mfd_core rfkill snd_timer snd usb_common soundcore video parport_pc parport intel_agp wmi intel_gtt backlight e1000e agpgart evdev [ 16.132456] CPU: 0 UID: 0 PID: 181 Comm: kworker/u8:6 Not tainted 6.11.0-cl+ #143 [ 16.132460] Hardware name: Hewlett-Packard HP Compaq 6910p/30BE, BIOS 68MCU Ver. F.19 07/06/2010 [ 16.132463] Workqueue: async async_run_entry_fn [ 16.132469] RIP: 0010:ieee80211_reconfig+0x8f/0x14b0 [mac80211] [ 16.132501] Code: da 02 00 00 c6 83 ad 05 00 00 00 48 89 df e8 98 1b fc ff 85 c0 41 89 c7 0f 84 e9 02 00 00 48 c7 c7 a0 e6 48 a0 e8 d1 77 c4 e0 <0f> 0b eb 2d 84 c0 0f 85 8b 01 00 00 c6 87 ad 05 00 00 00 e8 69 1b [ 16.132504] RSP: 0018:ffffc9000029fcf0 EFLAGS: 00010282 [ 16.132507] RAX: 0000000000000000 RBX: ffff8880072008e0 RCX: 0000000000000001 [ 16.132509] RDX: ffffffff81f21a18 RSI: 0000000000000086 RDI: 0000000000000001 [ 16.132510] RBP: ffff8880072003c0 R08: 0000000000000000 R09: 0000000000000003 [ 16.132512] R10: 0000000000000000 R11: ffff88807e5b0000 R12: 0000000000000001 [ 16.132514] R13: 0000000000000000 R14: 0000000000000000 R15: 00000000ffffff92 [ 16.132515] FS: 0000000000000000(0000) GS:ffff88807c200000(0000) knlGS:0000000000000000 [ 16.132517] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 16.132519] CR2: 000055dd43786c08 CR3: 000000000978f000 CR4: 00000000000006f0 [ 16.132521] Call Trace: [ 16.132525] <TASK> [ 16.132526] ? __warn+0x77/0x120 [ 16.132532] ? ieee80211_reconfig+0x8f/0x14b0 [mac80211] [ 16.132564] ? report_bug+0x15c/0x190 [ 16.132568] ? handle_bug+0x36/0x70 [ 16.132571] ? exc_invalid_op+0x13/0x60 [ 16.132573] ? asm_exc_invalid_op+0x16/0x20 [ 16.132579] ? ieee80211_reconfig+0x8f/0x14b0 [mac80211] [ 16.132611] ? snd_hdac_bus_init_cmd_io+0x24/0x200 [snd_hda_core] [ 16.132617] ? pick_eevdf+0x133/0x1c0 [ 16.132622] ? check_preempt_wakeup_fair+0x70/0x90 [ 16.132626] ? wakeup_preempt+0x4a/0x60 [ 16.132628] ? ttwu_do_activate.isra.0+0x5a/0x190 [ 16.132632] wiphy_resume+0x79/0x1a0 [cfg80211] [ 16.132675] ? wiphy_suspend+0x2a0/0x2a0 [cfg80211] [ 16.132697] dpm_run_callback+0x75/0x1b0 [ 16.132703] device_resume+0x97/0x200 [ 16.132707] async_resume+0x14/0x20 [ 16.132711] async_run_entry_fn+0x1b/0xa0 [ 16.132714] process_one_work+0x13d/0x350 [ 16.132718] worker_thread+0x2be/0x3d0 [ 16.132722] ? cancel_delayed_work_sync+0x70/0x70 [ 16.132725] kthread+0xc0/0xf0 [ 16.132729] ? kthread_park+0x80/0x80 [ 16.132732] ret_from_fork+0x28/0x40 [ 16.132735] ? kthread_park+0x80/0x80 [ 16.132738] ret_from_fork_asm+0x11/0x20 [ 16.132741] </TASK> [ 16.132742] ---[ end trace 0000000000000000 ]--- [ 16.132930] ------------[ cut here ]------------ [ 16.132932] WARNING: CPU: 0 PID: 181 at net/mac80211/driver-ops.c:41 drv_stop+0xe7/0xf0 [mac80211] [ 16.132957] Modules linked in: ctr ccm sch_fq_codel xt_tcpudp xt_multiport xt_state iptable_filter iptable_nat nf_nat nf_conntrack nf_defrag_ipv4 ip_tables x_tables binfmt_misc joydev mousedev btusb btrtl btintel btbcm bluetooth ecdh_generic ecc iTCO_wdt i2c_dev iwl4965 iwlegacy coretemp snd_hda_codec_analog pcspkr psmouse mac80211 snd_hda_codec_generic libarc4 sdhci_pci cqhci sha256_generic sdhci libsha256 firewire_ohci snd_hda_intel snd_intel_dspcfg mmc_core snd_hda_codec snd_hwdep firewire_core led_class iosf_mbi snd_hda_core uhci_hcd lpc_ich crc_itu_t cfg80211 ehci_pci ehci_hcd snd_pcm usbcore mfd_core rfkill snd_timer snd usb_common soundcore video parport_pc parport intel_agp wmi intel_gtt backlight e1000e agpgart evdev [ 16.133014] CPU: 0 UID: 0 PID: 181 Comm: kworker/u8:6 Tainted: G W 6.11.0-cl+ #143 [ 16.133018] Tainted: [W]=WARN [ 16.133019] Hardware name: Hewlett-Packard HP Compaq 6910p/30BE, BIOS 68MCU Ver. F.19 07/06/2010 [ 16.133021] Workqueue: async async_run_entry_fn [ 16.133025] RIP: 0010:drv_stop+0xe7/0xf0 [mac80211] [ 16.133048] Code: 48 85 c0 74 0e 48 8b 78 08 89 ea 48 89 de e8 e0 87 04 00 65 ff 0d d1 de c4 5f 0f 85 42 ff ff ff e8 be 52 c2 e0 e9 38 ff ff ff <0f> 0b 5b 5d c3 0f 1f 40 00 41 54 49 89 fc 55 53 48 89 f3 2e 2e 2e [ 16.133050] RSP: 0018:ffffc9000029fc50 EFLAGS: 00010246 [ 16.133053] RAX: 0000000000000000 RBX: ffff8880072008e0 RCX: ffff88800377f6c0 [ 16.133054] RDX: 0000000000000001 RSI: 0000000000000000 RDI: ffff8880072008e0 [ 16.133056] RBP: 0000000000000000 R08: ffffffff81f238d8 R09: 0000000000000000 [ 16.133058] R10: ffff8880080520f0 R11: 0000000000000000 R12: ffff888008051c60 [ 16.133060] R13: ffff8880072008e0 R14: 0000000000000000 R15: ffff8880072011d8 [ 16.133061] FS: 0000000000000000(0000) GS:ffff88807c200000(0000) knlGS:0000000000000000 [ 16.133063] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 16.133065] CR2: 000055dd43786c08 CR3: 000000000978f000 CR4: 00000000000006f0 [ 16.133067] Call Trace: [ 16.133069] <TASK> [ 16.133070] ? __warn+0x77/0x120 [ 16.133075] ? drv_stop+0xe7/0xf0 [mac80211] [ 16.133098] ? report_bug+0x15c/0x190 [ 16.133100] ? handle_bug+0x36/0x70 [ 16.133103] ? exc_invalid_op+0x13/0x60 [ 16.133105] ? asm_exc_invalid_op+0x16/0x20 [ 16.133109] ? drv_stop+0xe7/0xf0 [mac80211] [ 16.133132] ieee80211_do_stop+0x55a/0x810 [mac80211] [ 16.133161] ? fq_codel_reset+0xa5/0xc0 [sch_fq_codel] [ 16.133164] ieee80211_stop+0x4f/0x180 [mac80211] [ 16.133192] __dev_close_many+0xa2/0x120 [ 16.133195] dev_close_many+0x90/0x150 [ 16.133198] dev_close+0x5d/0x80 [ 16.133200] cfg80211_shutdown_all_interfaces+0x40/0xe0 [cfg80211] [ 16.133223] wiphy_resume+0xb2/0x1a0 [cfg80211] [ 16.133247] ? wiphy_suspend+0x2a0/0x2a0 [cfg80211] [ 16.133269] dpm_run_callback+0x75/0x1b0 [ 16.133273] device_resume+0x97/0x200 [ 16.133277] async_resume+0x14/0x20 [ 16.133280] async_run_entry_fn+0x1b/0xa0 [ 16.133283] process_one_work+0x13d/0x350 [ 16.133287] worker_thread+0x2be/0x3d0 [ 16.133290] ? cancel_delayed_work_sync+0x70/0x70 [ 16.133294] kthread+0xc0/0xf0 [ 16.133296] ? kthread_park+0x80/0x80 [ 16.133299] ret_from_fork+0x28/0x40 [ 16.133302] ? kthread_park+0x80/0x80 [ 16.133304] ret_from_fork_asm+0x11/0x20 [ 16.133307] </TASK> [ 16.133308] ---[ end trace 0000000000000000 ]--- [ 16.133335] ieee80211 phy0: PM: dpm_run_callback(): wiphy_resume [cfg80211] returns -110 [ 16.133360] ieee80211 phy0: PM: failed to restore async: error -110 Cc: [email protected] Cc: Stanislaw Gruszka <[email protected]> Cc: Kalle Valo <[email protected]> Cc: [email protected] Signed-off-by: Ville Syrjälä <[email protected]> Acked-by: Stanislaw Gruszka <[email protected]> Signed-off-by: Kalle Valo <[email protected]> Link: https://patch.msgid.link/[email protected]
2024-09-19wifi: iwlegacy: Fix "field-spanning write" warning in il_enqueue_hcmd()Ben Hutchings2-1/+24
iwlegacy uses command buffers with a payload size of 320 bytes (default) or 4092 bytes (huge). The struct il_device_cmd type describes the default buffers and there is no separate type describing the huge buffers. The il_enqueue_hcmd() function works with both default and huge buffers, and has a memcpy() to the buffer payload. The size of this copy may exceed 320 bytes when using a huge buffer, which now results in a run-time warning: memcpy: detected field-spanning write (size 1014) of single field "&out_cmd->cmd.payload" at drivers/net/wireless/intel/iwlegacy/common.c:3170 (size 320) To fix this: - Define a new struct type for huge buffers, with a correctly sized payload field - When using a huge buffer in il_enqueue_hcmd(), cast the command buffer pointer to that type when looking up the payload field Reported-by: Martin-Éric Racine <[email protected]> References: https://bugs.debian.org/1062421 References: https://bugzilla.kernel.org/show_bug.cgi?id=219124 Signed-off-by: Ben Hutchings <[email protected]> Fixes: 54d9469bc515 ("fortify: Add run-time WARN for cross-field memcpy()") Tested-by: Martin-Éric Racine <[email protected]> Tested-by: Brandon Nielsen <[email protected]> Acked-by: Stanislaw Gruszka <[email protected]> Signed-off-by: Kalle Valo <[email protected]> Link: https://patch.msgid.link/ZuIhQRi/[email protected]
2024-09-18wifi: mt76: do not increase mcu skb refcount if retry is not supportedFelix Fietkau1-2/+5
If mcu_skb_prepare_msg is not implemented, incrementing skb refcount does not work for mcu message retry. In some cases (e.g. on SDIO), shared skbs can trigger a BUG_ON, crashing the system. Fix this by only incrementing refcount if retry is actually supported. Fixes: 3688c18b65ae ("wifi: mt76: mt7915: retry mcu messages") Closes: https://lore.kernel.org/r/d907b13a-f8be-4cb8-a0bb-560a21278041@notapiano/ Reported-by: Nícolas F. R. A. Prado <[email protected]> #KernelCI Tested-by: Alper Nebi Yasak <[email protected]> Signed-off-by: Felix Fietkau <[email protected]> Signed-off-by: Kalle Valo <[email protected]> Link: https://patch.msgid.link/[email protected]
2024-09-18wifi: rtw89: coex: add debug message of link counts on 2/5GHz bands for ↵Ping-Ke Shih1-0/+2
wl_info v7 The counts will be used by MLO, and it is ongoing to add the code, so add debug message in todo part to avoid warnings reported by clang: coex.c:6323:23: warning: variable 'cnt_2g' set but not used [-Wunused-but-set-variable] 6323 | u8 i, mode, cnt = 0, cnt_2g = 0, cnt_5g = 0, ... | ^ coex.c:6323:35: warning: variable 'cnt_5g' set but not used [-Wunused-but-set-variable] 6323 | u8 i, mode, cnt = 0, cnt_2g = 0, cnt_5g = 0, ... | ^ Signed-off-by: Ping-Ke Shih <[email protected]> Signed-off-by: Kalle Valo <[email protected]> Link: https://patch.msgid.link/[email protected]
2024-09-16Merge tag 'net-next-6.12' of ↵Linus Torvalds1458-13760/+69936
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next Pull networking updates from Jakub Kicinski: "The zero-copy changes are relatively significant, but regression risk should be contained. The feature needs to be used to cause trouble. Also it feels like we got an order of magnitude more semi-automated "refactoring" chaff than usual, I wonder if it's just us. Core & protocols: - Support Device Memory TCP, ability to zero-copy receive TCP payloads to a DMABUF region of memory while packet headers land separately in normal kernel buffers, and TCP processes then as usual. - The ability to read the PTP PHC (Physical Hardware Clock) alongside MONOTONIC_RAW timestamps with PTP_SYS_OFFSET_EXTENDED. Previously only CLOCK_REALTIME was supported. - Allow matching on all bits of IP DSCP for routing decisions. Previously we only supported on matching TOS bits in IPv4 which is a narrower interpretation of the same header field. - Increase the range of weights used for multi-path routing from 8 bits to 16 bits. - Add support for IPv6 PIO p flag in the Prefix Information Option per draft-ietf-6man-pio-pflag. - IPv6 IOAM6 support for new tunsrc encap mode for better performance. - Detect destinations which blackhole MPTCP traffic and avoid initiating MPTCP connections to them for a certain period of time, 1h by default. - Improve IPsec control path performance by removing the inexact policies list. - AF_VSOCK: add support for SIOCOUTQ ioctl. - Add enum for reasons TCP reset was sent for easier tracing. - Add SMC ringbufs usage statistics. Drivers: - Handle netconsole setup failures more gracefully, don't fail loading, retain the specified target as disabled. - Extend bonding's IPsec offload pass thru capabilities (ESN, stats). Filtering: - Add TCP_BPF_SOCK_OPS_CB_FLAGS to bpf_*sockopt() to address the case when long-lived sockets miss a chance to set additional callbacks if a sockops program was not attached early in their lifetime. - Support using BPF skb helpers in tracepoints. - Conntrack Netlink: support CTA_FILTER for flush. - Improve SCTP support in nfnetlink_queue. - Improve performance of large nftables flush transactions. Things we sprinkled into general kernel code: - selftests: support setting an "interpreter" for script files; make it easy to run as separate cases tests where one "interpreter" is fed various test descriptions (in our case packet sequences). Driver API: - Extend core and ethtool APIs to support many PHYs connected to a single interface (PHY topologies). - Extend cable diagnostics to specify whether Time Domain Reflectometry (TDR) or Active Link Cable Diagnostic (ALCD) was used. - Add library for implementing MAC-PHY Ethernet drivers for SPI devices compatible with Open Alliance 10BASE-T1x MAC-PHY Serial Interface (TC6) standard. - Add helpers to the PHY framework, for PHYs following the Open Alliance standards: - 1000BaseT1 link settings - cable test and diagnostics - Support listing / dumping all allocated RSS contexts. - Add configuration for frequency Embedded SYNC in DPLL, which magically embeds sync pulses into Ethernet signaling. Device drivers: - Ethernet high-speed NICs: - Broadcom (bnxt): - use better FW APIs for queue reset - support QOS and TPID settings for the SR-IOV VLAN - support dynamic MSI-X allocation - Intel (100G, ice, idpf): - ice: support PCIe subfunctions - iavf: add support for TC U32 filters on VFs - ice: support Embedded SYNC in DPLL - nVidia/Mellanox (mlx5): - support HW managed steering tables - support PCIe PTM cross timestamping - AMD/Pensando: - ionic: use page_pool to increase Rx performance - Cisco (enic): - report per-queue statistics - Ethernet virtual: - Microsoft vNIC: - mana: support configuring ring length - netvsc: enable more channels on systems with many CPUs - IBM veth: - optimize polling to improve TCP_RR performance - optimize performance of Tx handling - VirtIO net: - synchronize the operstate with the admin state to allow a lower virtio-net to propagate the link status to an upper device like macvlan - Ethernet NICs consumer, and embedded: - Add driver for Realtek automotive PCIe devices (RTL9054, RTL9068, RTL9072, RTL9075, RTL9068, RTL9071) - Add driver for Microchip LAN8650/1 10BASE-T1S MAC-PHY. - Microchip: - lan743x: use phylink - support WOL, EEE, pause, link settings - add Wake-on-LAN support for KSZ87xx family - add KSZ8895/KSZ8864 switch support - factor out FDMA code and use it in sparx5 and lan966x (including DCB support in both) - Synopsys (stmmac): - support frame preemption (configured using TC and ethtool) - support Loongson DWMAC (GMAC v3.73) - support RockChips RK3576 DWMAC - TI: - am65-cpsw: add multi queue RX support - icssg-prueth: HSR offload support - Cadence (macb): - enable software (hrtimer based) IRQ coalescing by default - Xilinx (axinet): - expose HW statistics - improve multicast filtering - relax Rx checksum offload constraints - MediaTek: - mt7530: add EN7581 support - Aspeed (ftgmac100): - report link speed and duplex - Intel: - igc: add mqprio offload - igc: report EEE configuration - RealTek (r8169): - add support for RTL8126A rev.b - Vitesse (vsc73xx): - implement FDB add/del/dump operations - Freescale (fs_enet): - use phylink - Ethernet PHYs: - vitesse: implement downshift and MDI-X in vsc73xx PHYs - microchip: support LAN887x, supporting IEEE 802.3bw (100BASE-T1) and IEEE 802.3bp (1000BASE-T1) specifications - add Applied Micro QT2025 PHY driver (in Rust) - add Motorcomm yt8821 2.5G Ethernet PHY driver - CAN: - add driver for Rockchip RK3568 CAN-FD controller - flexcan: add wakeup support for imx95 - kvaser_usb: set hardware timestamp on transmitted packets - WiFi: - mac80211/cfg80211: - EHT rate support in AQL airtime fairness - handle DFS (radar detection) per link in Multi-Link Operation - RealTek (rtw89): - support RTL8852BT and 8852BE-VT (WiFi 6) - support hardware rfkill - support HW encryption in unicast management frames - support Wake-on-WLAN with supported network detection - RealTek (rtw89): - improve Rx performance by using USB frame aggregation - support USB 3 with RTL8822CU/RTL8822BU - Intel (iwlwifi/mvm): - offload RLC/SMPS functionality to firmware - Marvell (mwifiex): - add host based MLME to enable WPA3 - Bluetooth: - add support for Amlogic HCI UART protocol - add support for ISO data/packets to Intel and NXP drivers" * tag 'net-next-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1303 commits) net/mlx5: HWS, check the correct variable in hws_send_ring_alloc_sq() netfilter: nft_socket: Fix a NULL vs IS_ERR() bug in nft_socket_cgroup_subtree_level() ice: Fix a NULL vs IS_ERR() check in probe() ice: Fix a couple NULL vs IS_ERR() bugs net: ethernet: fs_enet: Make the per clock optional net: ti: icssg-prueth: Add multicast filtering support in HSR mode net: ti: icssg-prueth: Enable HSR Tx duplication, Tx Tag and Rx Tag offload net: ti: icssg-prueth: Add support for HSR frame forward offload net: ti: icssg-prueth: Stop hardcoding def_inc net: ti: icss-iep: Move icss_iep structure net: ibm: emac: get rid of wol_irq net: ibm: emac: remove all waiting code net: ibm: emac: replace of_get_property net: ibm: emac: use netdev's phydev directly net: ibm: emac: use devm for register_netdev net: ibm: emac: remove mii_bus with devm net: ibm: emac: use devm for of_iomap net: ibm: emac: manage emac_irq with devm net: ibm: emac: use devm for alloc_etherdev octeontx2-af: debugfs: Add Channel info to RPM map ...
2024-09-15Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski13-35/+76
Merge in late fixes to prepare for the 6.12 net-next PR. No conflicts or adjacent changes. Signed-off-by: Jakub Kicinski <[email protected]>
2024-09-15net/mlx5: HWS, check the correct variable in hws_send_ring_alloc_sq()Dan Carpenter1-1/+1
There is a copy and paste bug so this code checks "sq->dep_wqe" where "sq->wr_priv" was intended. It could result in a NULL pointer dereference. Fixes: 2ca62599aa0b ("net/mlx5: HWS, added send engine and context handling") Signed-off-by: Dan Carpenter <[email protected]> Reviewed-by: Simon Horman <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2024-09-15netfilter: nft_socket: Fix a NULL vs IS_ERR() bug in ↵Dan Carpenter1-2/+2
nft_socket_cgroup_subtree_level() The cgroup_get_from_path() function never returns NULL, it returns error pointers. Update the error handling to match. Fixes: 7f3287db6543 ("netfilter: nft_socket: make cgroupsv2 matching work with namespaces") Signed-off-by: Dan Carpenter <[email protected]> Acked-by: Florian Westphal <[email protected]> Acked-by: Pablo Neira Ayuso <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2024-09-15ice: Fix a NULL vs IS_ERR() check in probe()Dan Carpenter1-2/+2
The ice_allocate_sf() function returns error pointers on error. It doesn't return NULL. Update the check to match. Fixes: 177ef7f1e2a0 ("ice: base subfunction aux driver") Signed-off-by: Dan Carpenter <[email protected]> Reviewed-by: Simon Horman <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2024-09-15ice: Fix a couple NULL vs IS_ERR() bugsDan Carpenter1-4/+4
The ice_repr_create() function returns error pointers. It never returns NULL. Fix the callers to check for IS_ERR(). Fixes: 977514fb0fa8 ("ice: create port representor for SF") Fixes: 415db8399d06 ("ice: make representor code generic") Signed-off-by: Dan Carpenter <[email protected]> Reviewed-by: Simon Horman <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2024-09-15net: ethernet: fs_enet: Make the per clock optionalMaxime Chevallier1-1/+1
Some platforms that use fs_enet don't have the PER register clock. This optional dependency on the clock was incorrectly made mandatory when switching to devm_ accessors. Reported-by: Christophe JAILLET <[email protected]> Closes: https://lore.kernel.org/netdev/[email protected]/ Fixes: c614acf6e8e1 ("net: ethernet: fs_enet: simplify clock handling with devm accessors") Signed-off-by: Maxime Chevallier <[email protected]> Reviewed-by: Christophe JAILLET <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2024-09-15Linux 6.11Linus Torvalds1-1/+1
2024-09-15Merge tag 'for-linus-6.11' of git://git.kernel.org/pub/scm/virt/kvm/kvmLinus Torvalds2-11/+7
Pull kvm fix from Paolo Bonzini: "Do not always honor guest PAT on CPUs that support self-snoop. This triggers an issue in the bochsdrm driver, which used ioremap() instead of ioremap_wc() to map the video RAM. The revert lets video RAM use the WB memory type instead of the slower UC memory type" * tag 'for-linus-6.11' of git://git.kernel.org/pub/scm/virt/kvm/kvm: Revert "KVM: VMX: Always honor guest PAT on CPUs that support self-snoop"
2024-09-15Revert "KVM: VMX: Always honor guest PAT on CPUs that support self-snoop"Paolo Bonzini2-11/+7
This reverts commit 377b2f359d1f71c75f8cc352b5c81f2210312d83. This caused a regression with the bochsdrm driver, which used ioremap() instead of ioremap_wc() to map the video RAM. After the commit, the WB memory type is used without the IGNORE_PAT, resulting in the slower UC memory type. In fact, UC is slow enough to basically cause guests to not boot... but only on new processors such as Sapphire Rapids and Cascade Lake. Coffee Lake for example works properly, though that might also be an effect of being on a larger, more NUMA system. The driver has been fixed but that does not help older guests. Until we figure out whether Cascade Lake and newer processors are working as intended, revert the commit. Long term we might add a quirk, but the details depend on whether the processors are working as intended: for example if they are, the quirk might reference bochs-compatible devices, e.g. in the name and documentation, so that userspace can disable the quirk by default and only leave it enabled if such a device is being exposed to the guest. If instead this is actually a bug in CLX+, then the actions we need to take are different and depend on the actual cause of the bug. Signed-off-by: Paolo Bonzini <[email protected]>
2024-09-14Merge branch 'introduce-hsr-offload-support-for-icssg'Jakub Kicinski8-92/+290
MD Danish Anwar says: ==================== Introduce HSR offload support for ICSSG This series introduces HSR offload support for ICSSG driver. To support HSR offload to hardware, ICSSG HSR firmware is used. This series introduces, 1. HSR frame offload support for ICSSG driver. 2. HSR Tx Packet duplication offload 3. HSR Tx Tag and Rx Tag offload 4. Multicast filtering support in HSR offload mode. 5. Dependencies related to IEP. HSR Test Setup: -------------- ___________ ___________ ___________ | | Link AB | | Link BC | | __| AM64* |_________| AM64 |_________| AM64* |___ | | Station A | | Station B | | Station C | | | |___________| |___________| |___________| | | | |______________________________________________________________| Link CA *Could be any device that supports two ethernet interfaces. Steps to switch to HSR frame forward offload mode: ------------------------------------------------- Example assuming eth1, eth2 ports of ICSSG1 on AM64-EVM 1) Enable HSR offload for both interfaces ethtool -K eth1 hsr-fwd-offload on ethtool -K eth1 hsr-dup-offload on ethtool -K eth1 hsr-tag-ins-offload on ethtool -K eth1 hsr-tag-rm-offload on ethtool -K eth2 hsr-fwd-offload on ethtool -K eth2 hsr-dup-offload on ethtool -K eth2 hsr-tag-ins-offload on ethtool -K eth2 hsr-tag-rm-offload on 2) Create HSR interface and add slave interfaces to it ip link add name hsr0 type hsr slave1 eth1 slave2 eth2 \ supervision 45 version 1 3) Add IP address to the HSR interface ip addr add <IP_ADDR>/24 dev hsr0 4) Bring up the HSR interface ip link set hsr0 up Switching back to previous mode: -------------------------------- 1) Delete HSR interface ip link delete hsr0 2) Disable HSR port-to-port offloading mode, packet duplication ethtool -K eth1 hsr-fwd-offload off ethtool -K eth1 hsr-dup-offload off ethtool -K eth1 hsr-tag-ins-offload off ethtool -K eth1 hsr-tag-rm-offload off ethtool -K eth2 hsr-fwd-offload off ethtool -K eth2 hsr-dup-offload off ethtool -K eth2 hsr-tag-ins-offload off ethtool -K eth2 hsr-tag-rm-offload off Testing the port-to-port frame forward offload feature: ----------------------------------------------------- 1) Connect the LAN cables as shown in the test setup. 2) Configure Station A and Station C in HSR non-offload mode. 3) Configure Station B is HSR offload mode. 4) Since HSR is a redundancy protocol, disconnect cable "Link CA", to ensure frames from Station A reach Station C only through Station B. 5) Run iperf3 Server on Station C and client on station A. 7) Check the CPU usage on Station B. CPU usage report on Station B using mpstat when running UDP iperf3: ------------------------------------------------------------------- 1) Non-Offload case ------------------- CPU %usr %nice %sys %iowait %irq %soft %steal %guest %idle all 0.00 0.00 0.50 0.00 3.52 29.15 0.00 0.00 66.83 0 0.00 0.00 0.00 0.00 7.00 58.00 0.00 0.00 35.00 1 0.00 0.00 0.99 0.00 0.99 0.00 0.00 0.00 98.02 2) Offload case --------------- CPU %usr %nice %sys %iowait %irq %soft %steal %guest %idle all 0.00 0.00 0.00 0.00 0.50 0.00 0.00 0.00 99.50 0 0.00 0.00 0.99 0.00 0.00 0.00 0.00 0.00 99.01 1 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 100.00 Note: 1) At the very least, hsr-fwd-offload must be enabled. Without offloading the port-to-port offload, other HSR offloads cannot be enabled. 2) hsr-tag-ins-offload and hsr-dup-offload are tightly coupled in the firmware implementation. They both need to be enabled / disabled together. v1: https://lore.kernel.org/[email protected]/ v2: https://lore.kernel.org/[email protected] v3: https://lore.kernel.org/[email protected]/ v4: https://lore.kernel.org/[email protected]/ v5: https://lore.kernel.org/[email protected]/ [0] https://lore.kernel.org/[email protected]/ [1] https://lore.kernel.org/[email protected]/ [2] https://lore.kernel.org/[email protected]/ [3] https://lore.kernel.org/[email protected]/ [4] https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net.git/commit/?id=e846be0fba85 ==================== Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2024-09-14net: ti: icssg-prueth: Add multicast filtering support in HSR modeMD Danish Anwar1-2/+40
Add support for multicast filtering in HSR mode Reviewed-by: Roger Quadros <[email protected]> Signed-off-by: MD Danish Anwar <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2024-09-14net: ti: icssg-prueth: Enable HSR Tx duplication, Tx Tag and Rx Tag offloadRavi Gunasekaran5-5/+58
The HSR stack allows to offload its Tx packet duplication functionality to the hardware. Enable this offloading feature for ICSSG driver. Add support to offload HSR Tx Tag Insertion and Rx Tag Removal and duplicate discard. hsr tag insertion offload and hsr dup offload are tightly coupled in firmware implementation. Both these features need to be enabled / disabled together. Duplicate discard is done as part of RX tag removal and it is done by the firmware. When driver sends the r30 command ICSSG_EMAC_HSR_RX_OFFLOAD_ENABLE, firmware does RX tag removal as well as duplicate discard. Signed-off-by: Ravi Gunasekaran <[email protected]> Signed-off-by: MD Danish Anwar <[email protected]> Reviewed-by: Roger Quadros <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2024-09-14net: ti: icssg-prueth: Add support for HSR frame forward offloadMD Danish Anwar4-12/+119
Add support for offloading HSR port-to-port frame forward to hardware. When the slave interfaces are added to the HSR interface, the PRU cores will be stopped and ICSSG HSR firmwares will be loaded to them. Similarly, when HSR interface is deleted, the PRU cores will be restarted and the last used firmwares will be reloaded. PRUeth interfaces will be back to the last used mode. This commit also renames some APIs that are common between switch and hsr mode with '_fw_offload' suffix. Signed-off-by: MD Danish Anwar <[email protected]> Reviewed-by: Roger Quadros <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2024-09-14net: ti: icssg-prueth: Stop hardcoding def_incMD Danish Anwar1-1/+2
The def_inc is stored in icss_iep structure. Currently default increment (ns per clock tick) is hardcoded to 4 (Clock frequency being 250 MHz). Change this to use the iep->def_inc variable as the iep structure is now accessible to the driver files. Reviewed-by: Roger Quadros <[email protected]> Signed-off-by: MD Danish Anwar <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2024-09-14net: ti: icss-iep: Move icss_iep structureMD Danish Anwar2-73/+72
Move icss_iep structure definition and to icss_iep.h file so that the structure members can be used / accessed by all icssg driver files. Reviewed-by: Simon Horman <[email protected]> Reviewed-by: Jacob Keller <[email protected]> Reviewed-by: Roger Quadros <[email protected]> Signed-off-by: MD Danish Anwar <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2024-09-14Merge tag 'pinctrl-v6.11-4' of ↵Linus Torvalds2-5/+10
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl Pull pin control fixes from Linus Walleij: - One Intel patch that I mistakenly merged into for-next despite it belonging in fixes: add Arrow Lake-H/U ACPI ID so this Arrow Lake chip probes. - One fix making the CY895x0 reg cache work, which is good because it makes the device work too. * tag 'pinctrl-v6.11-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: pinctrl: pinctrl-cy8c95x0: Fix regcache pinctrl: meteorlake: Add Arrow Lake-H/U ACPI ID
2024-09-14Merge tag 'sound-6.11' of ↵Linus Torvalds7-6/+11
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound Pull sound fixes from Takashi Iwai: "A few last-minute ASoC fixes and MAINTAINERS update. All look small, obvious and nice-to-have fixes for 6.11-final" * tag 'sound-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: ASoC: meson: axg-card: fix 'use-after-free' ASoC: codecs: avoid possible garbage value in peb2466_reg_read() MAINTAINERS: update Pierre Bossart's email and role ASoC: tas2781: fix to save the dsp bin file name into the correct array in case name_prefix is not NULL ASoC: Intel: soc-acpi-intel-mtl-match: add missing empty item ASoC: Intel: soc-acpi-intel-lnl-match: add missing empty item
2024-09-14Merge tag '6.11-rc7-SMB3-client-fix' of git://git.samba.org/sfrench/cifs-2.6Linus Torvalds1-1/+1
Pull smb client fix from Steve French: "Fix for packet signing of write" * tag '6.11-rc7-SMB3-client-fix' of git://git.samba.org/sfrench/cifs-2.6: cifs: Fix signature miscalculation
2024-09-14Merge tag 'asoc-fix-v6.11-rc7' of ↵Takashi Iwai7-6/+11
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus ASoC: Fixes for v6.11 A few last minute fixes, plus an update for Pierre's contact details and status. It'd be good to get these into v6.11 (especially the MAINTAINERS update) but it wouldn't be the end of the world if they waited for the merge window, none of them are super remarkable and it's just a question of timing that they're last minute.
2024-09-13Merge branch 'net-ibm-emac-modernize-a-bit'Jakub Kicinski2-152/+71
Rosen Penev says: ==================== net: ibm: emac: modernize a bit ==================== Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2024-09-13net: ibm: emac: get rid of wol_irqRosen Penev1-10/+3
This is completely unused. Signed-off-by: Rosen Penev <[email protected]> Reviewed-by: Andrew Lunn <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2024-09-13net: ibm: emac: remove all waiting codeRosen Penev1-48/+7
EPROBE_DEFER, which probably wasn't available when this driver was written, can be used instead of waiting manually. Signed-off-by: Rosen Penev <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2024-09-13net: ibm: emac: replace of_get_propertyRosen Penev1-11/+9
of_property_read_u32 can be used. Signed-off-by: Rosen Penev <[email protected]> Reviewed-by: Andrew Lunn <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2024-09-13net: ibm: emac: use netdev's phydev directlyRosen Penev2-30/+22
Avoids having to use own struct member. Signed-off-by: Rosen Penev <[email protected]> Reviewed-by: Andrew Lunn <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2024-09-13net: ibm: emac: use devm for register_netdevRosen Penev1-3/+1
Cleans it up automatically. No need to handle manually. Signed-off-by: Rosen Penev <[email protected]> Reviewed-by: Andrew Lunn <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2024-09-13net: ibm: emac: remove mii_bus with devmRosen Penev2-20/+13
Switching to devm management of mii_bus allows to remove mdiobus_unregister calls and thus avoids needing a mii_bus global struct member. Signed-off-by: Rosen Penev <[email protected]> Reviewed-by: Andrew Lunn <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2024-09-13net: ibm: emac: use devm for of_iomapRosen Penev1-8/+4
Allows removing manual iounmap. Signed-off-by: Rosen Penev <[email protected]> Reviewed-by: Andrew Lunn <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2024-09-13net: ibm: emac: manage emac_irq with devmRosen Penev1-18/+11
It's the last to go in remove. Safe to let devm handle it. Also move request_irq to probe for clarity. It's removed in _remove not close. Use dev_err_probe instead of printk. Handles EPROBE_DEFER automatically. Signed-off-by: Rosen Penev <[email protected]> Reviewed-by: Andrew Lunn <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2024-09-13net: ibm: emac: use devm for alloc_etherdevRosen Penev1-6/+3
Allows to simplify the code slightly. This is safe to do as free_netdev gets called last. Signed-off-by: Rosen Penev <[email protected]> Reviewed-by: Andrew Lunn <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2024-09-13octeontx2-af: debugfs: Add Channel info to RPM mapLinu Cherian1-4/+7
Display channel info in the RPM map debugfs output. With this, cat /sys/kernel/debug/cn10k/rvu_pf_rpm_map would display channel number for each device in addition to the existing data. Sample output: PCI dev RVU PF Func NIX block rpm LMAC CHAN 0002:02:00.0 0x400 NIX0 rpm0 LMAC0 256 Signed-off-by: Linu Cherian <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2024-09-13net: ethtool: phy: Don't set the context dev pointer for unfiltered DUMPMaxime Chevallier1-2/+0
The context info allows continuing DUMP requests, shall they fill the netlink buffer. In the case of filtered DUMP requests, a reference on the netdev is grabbed in the .start() callback and release in .done(). Unfiltered DUMP request don't need the dev pointer to be set in the context info, doing so will trigger an unwanted netdev_put() in .done(). Reported-by: [email protected] Closes: https://lore.kernel.org/netdev/[email protected]/ Fixes: 17194be4c8e1 ("net: ethtool: Introduce a command to list PHYs on an interface") Signed-off-by: Maxime Chevallier <[email protected]> Reviewed-by: Vadim Fedorenko <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2024-09-13Merge tag 'linux-can-next-for-6.12-20240911' of ↵Jakub Kicinski24-27/+27
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next Marc Kleine-Budde says: ==================== pull-request: can-next 2024-09-11 The first patch is by Uwe Kleine-König targets all CAN platform driver and switches back the remove function to struct platform_driver::remove(). A patch by Stefan Mätje fixes the help text of the ESD USB driver. Jake Hamby's patch masks an unneeded interrupt in the m_can driver. The last 2 patches target the rockchip_canfd driver. Arnd Bergmann's patch reworks the delay calculation for the timekeeping worker, a patch by me fixes the decoding of the error code register. * tag 'linux-can-next-for-6.12-20240911' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next: can: rockchip_canfd: rkcanfd_handle_error_int_reg_ec(): fix decoding of error code register can: rockchip_canfd: rkcanfd_timestamp_init(): rework delay calculation can: m_can: m_can_chip_config(): mask timestamp wraparound IRQ can: usb: Kconfig: Fix list of devices for esd_usb driver can: Switch back to struct platform_driver::remove() ==================== Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2024-09-13rtase: Fix error code in rtase_init_board()Dan Carpenter1-1/+2
Return an error if dma_set_mask_and_coherent() fails. Don't return success. Fixes: a36e9f5cfe9e ("rtase: Add support for a pci table in this module") Signed-off-by: Dan Carpenter <[email protected]> Reviewed-by: Simon Horman <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
Powered by cgit, Gruvboxed by Blaster4385.