Age | Commit message (Collapse) | Author | Files | Lines |
|
Replace deferred action function wrappers with equivalent ones defined
using the macro introduced by commit 56778b49c9a2 ("kunit: Add a macro to
wrap a deferred action function")
Signed-off-by: Marco Pagani <[email protected]>
Signed-off-by: Daniel Vetter <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
This was basically just another one of amdgpus hacks. The parameter
allowed to restart the scheduler without turning fence signaling on
again.
That this is absolutely not a good idea should be obvious by now since
the fences will then just sit there and never signal.
While at it cleanup the code a bit.
Signed-off-by: Christian König <[email protected]>
Reviewed-by: Matthew Brost <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
When the bridge is powered off, disable the IRQ until the next power on
to workaround an interrupt storm on some badly-designed hardware.
Signed-off-by: Pin-yen Lin <[email protected]>
Reviewed-by: Robert Foss <[email protected]>
Signed-off-by: Robert Foss <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
[Why]
Page table of compute VM in the VRAM will lost after gpu reset.
VRAM won't be restored since compute VM has no shadows.
[How]
Use higher 32-bit of vm->generation to record a vram_lost_counter.
Reset the VM state machine when vm->genertaion is not equal to
the new generation token.
v2: Check vm->generation instead of calling drm_sched_entity_error
in amdgpu_vm_validate.
v3: Use new generation token instead of vram_lost_counter for check.
Signed-off-by: ZhenGuo Yin <[email protected]>
Reviewed-by: Christian König <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
Cc: [email protected]
(cherry picked from commit 47c0388b0589cb481c294dcb857d25a214c46eb3)
|
|
To prevent below probe failure, add a check for models with VCN
IP v4.0.6 where VCN1 may be harvested.
v2:
Apply the same check to VCN IP v4.0 and v5.0.
[ 54.070117] RIP: 0010:vcn_v4_0_5_start_dpg_mode+0x9be/0x36b0 [amdgpu]
[ 54.071055] Code: 80 fb ff 8d 82 00 80 fe ff 81 fe 00 06 00 00 0f 43
c2 49 69 d5 38 0d 00 00 48 8d 71 04 c1 e8 02 4c 01 f2 48 89 b2 50 f6 02
00 <89> 01 48 8b 82 50 f6 02 00 48 8d 48 04 48 89 8a 50 f6 02 00 c7 00
[ 54.072408] RSP: 0018:ffffb17985f736f8 EFLAGS: 00010286
[ 54.072793] RAX: 00000000000000d6 RBX: ffff99a82f680000 RCX:
0000000000000000
[ 54.073315] RDX: ffff99a82f680000 RSI: 0000000000000004 RDI:
ffff99a82f680000
[ 54.073835] RBP: ffffb17985f73730 R08: 0000000000000001 R09:
0000000000000000
[ 54.074353] R10: 0000000000000008 R11: ffffb17983c05000 R12:
0000000000000000
[ 54.074879] R13: 0000000000000000 R14: ffff99a82f680000 R15:
0000000000000001
[ 54.075400] FS: 00007f8d9c79a000(0000) GS:ffff99ab2f140000(0000)
knlGS:0000000000000000
[ 54.075988] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 54.076408] CR2: 0000000000000000 CR3: 0000000140c3a000 CR4:
0000000000750ef0
[ 54.076927] PKRU: 55555554
[ 54.077132] Call Trace:
[ 54.077319] <TASK>
[ 54.077484] ? show_regs+0x69/0x80
[ 54.077747] ? __die+0x28/0x70
[ 54.077979] ? page_fault_oops+0x180/0x4b0
[ 54.078286] ? do_user_addr_fault+0x2d2/0x680
[ 54.078610] ? exc_page_fault+0x84/0x190
[ 54.078910] ? asm_exc_page_fault+0x2b/0x30
[ 54.079224] ? vcn_v4_0_5_start_dpg_mode+0x9be/0x36b0 [amdgpu]
[ 54.079941] ? vcn_v4_0_5_start_dpg_mode+0xe6/0x36b0 [amdgpu]
[ 54.080617] vcn_v4_0_5_set_powergating_state+0x82/0x19b0 [amdgpu]
[ 54.081316] amdgpu_device_ip_set_powergating_state+0x64/0xc0
[amdgpu]
[ 54.082057] amdgpu_vcn_ring_begin_use+0x6f/0x1d0 [amdgpu]
[ 54.082727] amdgpu_ring_alloc+0x44/0x70 [amdgpu]
[ 54.083351] amdgpu_vcn_dec_sw_ring_test_ring+0x40/0x110 [amdgpu]
[ 54.084054] amdgpu_ring_test_helper+0x22/0x90 [amdgpu]
[ 54.084698] vcn_v4_0_5_hw_init+0x87/0xc0 [amdgpu]
[ 54.085307] amdgpu_device_init+0x1f96/0x2780 [amdgpu]
[ 54.085951] amdgpu_driver_load_kms+0x1e/0xc0 [amdgpu]
[ 54.086591] amdgpu_pci_probe+0x19f/0x550 [amdgpu]
[ 54.087215] local_pci_probe+0x48/0xa0
[ 54.087509] pci_device_probe+0xc9/0x250
[ 54.087812] really_probe+0x1a4/0x3f0
[ 54.088101] __driver_probe_device+0x7d/0x170
[ 54.088443] driver_probe_device+0x24/0xa0
[ 54.088765] __driver_attach+0xdd/0x1d0
[ 54.089068] ? __pfx___driver_attach+0x10/0x10
[ 54.089417] bus_for_each_dev+0x8e/0xe0
[ 54.089718] driver_attach+0x22/0x30
[ 54.090000] bus_add_driver+0x120/0x220
[ 54.090303] driver_register+0x62/0x120
[ 54.090606] ? __pfx_amdgpu_init+0x10/0x10 [amdgpu]
[ 54.091255] __pci_register_driver+0x62/0x70
[ 54.091593] amdgpu_init+0x67/0xff0 [amdgpu]
[ 54.092190] do_one_initcall+0x5f/0x330
[ 54.092495] do_init_module+0x68/0x240
[ 54.092794] load_module+0x201c/0x2110
[ 54.093093] init_module_from_file+0x97/0xd0
[ 54.093428] ? init_module_from_file+0x97/0xd0
[ 54.093777] idempotent_init_module+0x11c/0x2a0
[ 54.094134] __x64_sys_finit_module+0x64/0xc0
[ 54.094476] do_syscall_64+0x58/0x120
[ 54.094767] entry_SYSCALL_64_after_hwframe+0x6e/0x76
Signed-off-by: Tim Huang <[email protected]>
Reviewed-by: Saleemkhan Jamadar <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
Cc: [email protected]
(cherry picked from commit 0b071245ddd98539d4f7493bdd188417fcf2d629)
|
|
The eeprom table is empty before initializing,
set eeprom table version first before initializing.
Changed from V1:
Reuse amdgpu_ras_set_eeprom_table_version function
Signed-off-by: Stanley.Yang <[email protected]>
Reviewed-by: Hawking Zhang <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
(cherry picked from commit 015b8a2fdf39a4c288ff24e7b715b8d9198e56dc)
|
|
The ras command shared memory is allocated from
VRAM and the response status of the command
buffer will not be zero due to gpu being in
fatal error state after ras UE error injection.
Signed-off-by: YiPeng Chai <[email protected]>
Reviewed-by: Hawking Zhang <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
(cherry picked from commit 8284951a6e79c6806c675e5f68a4cd425dd56bc4)
|
|
In the DML math_ceil2 function, there is one ASSERT if the significance
is equal to zero. However, significance might be equal to zero
sometimes, and this is not an issue for a ceil function, but the current
ASSERT will trigger warnings in those cases. This commit removes the
ASSERT if the significance is equal to zero to avoid unnecessary noise.
Cc: Mario Limonciello <[email protected]>
Cc: Alex Deucher <[email protected]>
Cc: [email protected]
Reviewed-by: Chaitanya Dhere <[email protected]>
Signed-off-by: Rodrigo Siqueira <[email protected]>
Signed-off-by: Aurabindo Pillai <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
(cherry picked from commit 332315885d3ccc6d8fe99700f3c2e4c24aa65ab7)
|
|
[why & how]
Need to make sure plane_state is initialized
before accessing its members.
Cc: Mario Limonciello <[email protected]>
Cc: Alex Deucher <[email protected]>
Cc: [email protected]
Reviewed-by: Xi (Alex) Liu <[email protected]>
Signed-off-by: Sung Joon Kim <[email protected]>
Signed-off-by: Aurabindo Pillai <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
(cherry picked from commit 295d91cbc700651782a60572f83c24861607b648)
|
|
For VCN/JPEG 4.0.3, use only the local addressing scheme.
- Mask bit higher than AID0 range
v2
remain the case for mmhub use master XCC
Signed-off-by: Jane Jian <[email protected]>
Reviewed-by: Lijo Lazar <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
(cherry picked from commit caaf576292f8ccef5cdc0ac16e77b87dbf6e17ab)
|
|
VCN 4.0.3 does not HDP flush with RRMT enabled. Instead, mmsch
will do the HDP flush.
This change is necessary for VCN v4.0.3, no need for backward compatibility
Signed-off-by: Lijo Lazar <[email protected]>
Signed-off-by: Jane Jian <[email protected]>
Reviewed-by: Hawking Zhang <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
(cherry picked from commit 49cfaebe48e97500a68d5322a8194736b0a2c3cf)
|
|
JPEG v4.0.3 doesn't support HDP flush when RRMT is enabled. Instead,
mmsch fw will do the flush.
This change is necessary for JPEG v4.0.3, no need for backward compatibility
Signed-off-by: Lijo Lazar <[email protected]>
Signed-off-by: Jane Jian <[email protected]>
Reviewed-by: Hawking Zhang <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
(cherry picked from commit 585e3fdb36f59c5cfed0ae06c852dc1df22b1d60)
|
|
Return 0 to avoid returning an uninitialized variable r.
Cc: [email protected]
Fixes: 230dd6bb6117 ("drm/amd/amdgpu: implement mode2 reset on smu_v13_0_10")
Signed-off-by: Ma Ke <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
(cherry picked from commit 6472de66c0aa18d50a4b5ca85f8272e88a737676)
|
|
If PCIe supports atomics, configure register to prevent DF from
breaking atomics in separate load/store operations.
Signed-off-by: David Belanger <[email protected]>
Reviewed-by: Hawking Zhang <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
(cherry picked from commit 666f14cab21b17ccc1bdfe1e82458aa429b3b7e0)
|
|
We seem to have a case where SDMA will sometimes miss a doorbell
if GFX is entering the powergating state when the doorbell comes in.
To workaround this, we can update the wptr via MMIO, however,
this is only safe because we disallow gfxoff in begin_ring() for
SDMA 5.2 and then allow it again in end_ring().
Enable this workaround while we are root causing the issue with
the HW team.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/3440
Tested-by: Friedrich Vock <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
Cc: [email protected]
(cherry picked from commit f2ac52634963fc38e4935e11077b6f7854e5d700)
|
|
Define DRM native context capset in the VirtIO-GPU protocol header.
Signed-off-by: Dmitry Osipenko <[email protected]>
Reviewed-by: Rob Clark <[email protected]>
Reviewed-by: Pierre-Eric Pelloux-Prayer <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
ILI9806E DSI TCON driver
Add Densitron DMT028VGHMCMI-1D 480x640 TFT matrix 2.83 inch panel
attached to Ilitek ILI9806E DSI TCON into the ILI9806E driver.
Note that the Densitron panels use different TCONs, this driver is for
the later panel, use panel-ilitek-st7701.c for the former panel:
DMT028VGHMCMI-1A - ST7701
DMT028VGHMCMI-1D - ILI9806E
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Michael Walle <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Neil Armstrong <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
ILI9806E DSI TCON
Document Densitron DMT028VGHMCMI-1D 480x640 TFT matrix 2.83 inch panel
attached to Ilitek ILI9806E DSI TCON in the ILI9806E bindings.
Signed-off-by: Marek Vasut <[email protected]>
Acked-by: Krzysztof Kozlowski <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Neil Armstrong <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Use public functions( drm_connector_helper_get_modes_fixed()) to
get porch parameters.
Signed-off-by: Zhaoxiong Lv <[email protected]>
Reviewed-by: Douglas Anderson <[email protected]>
Link: https://lore.kernel.org/r/20240723062615.14796-3-lvzhaoxiong@huaqin.corp-partner.google.com
Signed-off-by: Neil Armstrong <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/20240723062615.14796-3-lvzhaoxiong@huaqin.corp-partner.google.com
|
|
The current driver can only obtain the porch parameters
of boe-th101mb31ig002. Modify it to obtain the porch
parameters of the panel currently being used.
Reviewed-by: Douglas Anderson <[email protected]>
Signed-off-by: Zhaoxiong Lv <[email protected]>
Link: https://lore.kernel.org/r/20240723062615.14796-2-lvzhaoxiong@huaqin.corp-partner.google.com
Signed-off-by: Neil Armstrong <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/20240723062615.14796-2-lvzhaoxiong@huaqin.corp-partner.google.com
|
|
Enable prepare_prev_first flag for BF060Y8M-AJ0 panel so that the
previous controller should be prepared first before the prepare for
the panel is called.
This makes sure that the previous controller, likely to be a DSI host
controller should be initialized to LP-11 before the panel is powered up.
Suggested-by: Marijn Suijten <[email protected]>
Signed-off-by: Dang Huynh <[email protected]>
Reviewed-by: Neil Armstrong <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Neil Armstrong <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Single characters should be put into a sequence.
Thus use the corresponding function “seq_putc” for one selected call.
This issue was transformed by using the Coccinelle software.
Suggested-by: Christophe Jaillet <[email protected]>
Signed-off-by: Markus Elfring <[email protected]>
Reviewed-by: Lyude Paul <[email protected]>
Signed-off-by: Lyude Paul <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Make the default DP port preemphasis configurable via new DT property
"toshiba,pre-emphasis". This is useful in case the DP link properties
are known and starting link training from preemphasis setting of 0 dB
is not useful. The preemphasis can be set separately for both DP lanes
in range 0=0dB, 1=3.5dB, 2=6dB .
Acked-by: Alexander Stein <[email protected]>
Signed-off-by: Marek Vasut <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Document default DP port preemphasis configurable via new DT property
"toshiba,pre-emphasis". This is useful in case the DP link properties
are known and starting link training from preemphasis setting of 0 dB
is not useful. The preemphasis can be set separately for both DP lanes
in range 0=0dB, 1=3.5dB, 2=6dB .
This is an endpoint property, not a port property, because the TC9595
datasheet does mention that the DP might operate in some sort of split
mode, where each DP lane is used to feed one display, so in that case
there might be two endpoints.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Rob Herring (Arm) <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Prevent a NULL pointer access in intel_memory_regions_hw_probe.
Fixes: 05da7d9f717b ("drm/i915/gem: Downgrade stolen lmem setup warning")
Reported-by: Dan Carpenter <[email protected]>
Closes: https://gitlab.freedesktop.org/drm/i915/kernel/-/issues/11704
Signed-off-by: Jonathan Cavitt <[email protected]>
Reviewed-by: Nirmoy Das <[email protected]>
Reviewed-by: Andi Shyti <[email protected]>
Signed-off-by: Andi Shyti <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
(cherry picked from commit d75dec1fcbcb05b021c08b62551649567ab8955c)
Signed-off-by: Tvrtko Ursulin <[email protected]>
|
|
We're seeing a GPU hang issue on a CHV platform, which was caused by commit
bac24f59f454 ("drm/i915/execlists: Enable coarse preemption boundaries for
Gen8").
The Gen8 platform only supports timeslicing and doesn't have a preemption
mechanism, as its engines do not have a preemption timer.
Commit 751f82b353a6 ("drm/i915/gt: Only disable preemption on Gen8 render
engines") addressed this issue only for render engines. This patch extends
that fix by ensuring that preemption is not considered for all engines on
Gen8 platforms.
v4:
- Use the correct Fixes tag (Rodrigo Vivi)
- Reworded commit log (Andi Shyti)
v3:
- Inside need_preempt(), condition of can_preempt() is not required
as simplified can_preempt() is enough. (Chris Wilson)
v2: Simplify can_preempt() function (Tvrtko Ursulin)
Fixes: 751f82b353a6 ("drm/i915/gt: Only disable preemption on gen8 render engines")
Closes: https://gitlab.freedesktop.org/drm/i915/kernel/-/issues/11396
Suggested-by: Andi Shyti <[email protected]>
Signed-off-by: Nitin Gote <[email protected]>
Cc: Chris Wilson <[email protected]>
CC: <[email protected]> # v5.12+
Reviewed-by: Jonathan Cavitt <[email protected]>
Reviewed-by: Andi Shyti <[email protected]>
Signed-off-by: Andi Shyti <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
(cherry picked from commit 7df0be6e6280c6fca01d039864bb123e5e36604b)
Signed-off-by: Tvrtko Ursulin <[email protected]>
|
|
Limiting the allocation of higher order pages to the closest NUMA node
and enabling direct memory reclaim provides not only failsafe against
situations when memory becomes too much fragmented and the allocator is
not able to satisfy the request from the local node but falls back to
remote pages (HUGEPAGE) but also offers performance improvement.
Accessing remote pages suffers due to bandwidth limitations and could be
avoided if memory becomes defragmented and in most cases without using
manual compaction. (/proc/sys/vm/compact_memory)
Note: On certain distros such as RHEL, the proactive compaction is
disabled. (https://tinyurl.com/4f32f7rs)
v2 (chk): drop __GFP_RECLAIM since that is already set by GFP_USER
Cc: Dave Airlie <[email protected]>
Cc: Vlastimil Babka <[email protected]>
Cc: Daniel Vetter <[email protected]>
Reviewed-by: Christian König <[email protected]>
Signed-off-by: Rajneesh Bhardwaj <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Signed-off-by: Christian König <[email protected]>
|
|
The docs for dma_heap_get_name were incorrect, and since they were
duplicated in the header they were wrong there too.
The docs formatting was inconsistent so I tried to make it more
consistent across functions since I'm already in here doing cleanup.
Remove multiple unused includes and alphabetize.
Signed-off-by: T.J. Mercier <[email protected]>
Signed-off-by: Yong Wu <[email protected]>
[Yong: Just add a comment for "priv" to mute build warning]
Signed-off-by: Yunfei Dong <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Signed-off-by: Christian König <[email protected]>
|
|
TTM wants to get rid of the duplicate refcounting of the embedded GEM
object and its own reference count.
Hence, use of GEM object references where possible.
Also get rid of nouveau_bo_ref() and replace it with nouveau_bo_fini(),
which drops the initial reference we get from initializing a ttm_bo.
Reviewed-by: Ben Skeggs <[email protected]>
Acked-by: Christian König <[email protected]>
Signed-off-by: Danilo Krummrich <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
nouveau_bo_new_pin_map() and nouveau_bo_unmap_unpin_unref() are unused,
hence remove them.
Reviewed-by: Ben Skeggs <[email protected]>
Acked-by: Christian König <[email protected]>
Signed-off-by: Danilo Krummrich <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Calling nouveau_bo_ref() on a nouveau_bo without initializing it (and
hence the backing ttm_bo) leads to a refcount underflow.
Instead of calling nouveau_bo_ref() in the unwind path of
drm_gem_object_init(), clean things up manually.
Fixes: ab9ccb96a6e6 ("drm/nouveau: use prime helpers")
Reviewed-by: Ben Skeggs <[email protected]>
Reviewed-by: Christian König <[email protected]>
Signed-off-by: Danilo Krummrich <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
The raw EDIDs for each panel:
AUO
- B116XTN02.3
00 ff ff ff ff ff ff 00 06 af aa 73 00 00 00 00
00 21 01 04 95 1a 0e 78 02 6b f5 91 55 54 91 27
22 50 54 00 00 00 01 01 01 01 01 01 01 01 01 01
01 01 01 01 01 01 ce 1d 56 e2 50 00 1e 30 26 16
36 00 00 90 10 00 00 18 df 13 56 e2 50 00 1e 30
26 16 36 00 00 90 10 00 00 18 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 02
00 10 48 ff 0f 3c 7d 50 05 18 7d 20 20 20 00 67
- B116XAN06.1
00 ff ff ff ff ff ff 00 06 af 99 a1 00 00 00 00
00 1f 01 04 95 1a 0e 78 02 9e a5 96 59 58 96 28
1b 50 54 00 00 00 01 01 01 01 01 01 01 01 01 01
01 01 01 01 01 01 ce 1d 56 ea 50 00 1a 30 30 20
46 00 00 90 10 00 00 18 df 13 56 ea 50 00 1a 30
30 20 46 00 00 90 10 00 00 18 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 02
00 10 48 ff 0f 3c 7d 0c 0a 2a 7d 20 20 20 00 3a
- B116XAT04.1
00 ff ff ff ff ff ff 00 06 af b4 c4 00 00 00 00
12 22 01 04 95 1a 0e 78 02 9e a5 96 59 58 96 28
1b 50 54 00 00 00 01 01 01 01 01 01 01 01 01 01
01 01 01 01 01 01 ce 1d 56 ea 50 00 1a 30 30 20
46 00 00 90 10 00 00 18 df 13 56 ea 50 00 1a 30
30 20 46 00 00 90 10 00 00 18 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 02
00 10 48 ff 0f 3c 7d 0c 0a 2a 7d 20 20 20 00 e7
BOE
- NV116WHM-A4D
00 ff ff ff ff ff ff 00 09 e5 fa 0c 00 00 00 00
12 22 01 04 95 1a 0e 78 03 0b 55 9a 5f 58 95 28
1e 50 54 00 00 00 01 01 01 01 01 01 01 01 01 01
01 01 01 01 01 01 96 1d 56 c8 50 00 26 30 30 20
36 00 00 90 10 00 00 1a b9 13 56 c8 50 00 26 30
30 20 36 00 00 90 10 00 00 1a 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 02
00 0d 40 ff 0a 3c 7d 0f 0c 17 7d 00 00 00 00 1a
CMN
- N116BCA-EA2
00 ff ff ff ff ff ff 00 0d ae 5d 11 00 00 00 00
0f 21 01 04 95 1a 0e 78 03 67 75 98 59 53 90 27
1c 50 54 00 00 00 01 01 01 01 01 01 01 01 01 01
01 01 01 01 01 01 da 1d 56 e2 50 00 20 30 30 20
a6 00 00 90 10 00 00 1a e7 13 56 e2 50 00 20 30
30 20 a6 00 00 90 10 00 00 1a 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 02
00 0c 3d ff 0d 3c 7d 0d 0a 15 7d 00 00 00 00 0f
- N116BCP-EA2
00 ff ff ff ff ff ff 00 0d ae 61 11 00 00 00 00
0f 21 01 04 95 1a 0e 78 03 67 75 98 59 53 90 27
1c 50 54 00 00 00 01 01 01 01 01 01 01 01 01 01
01 01 01 01 01 01 da 1d 56 e2 50 00 20 30 30 20
a6 00 00 90 10 00 00 1a e7 13 56 e2 50 00 20 30
30 20 a6 00 00 90 10 00 00 1a 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 02
00 0c 3d ff 0d 3c 7d 0d 0a 15 7d 00 00 00 00 0b
Signed-off-by: Terry Hsiao <[email protected]>
Reviewed-by: Douglas Anderson <[email protected]>
Signed-off-by: Douglas Anderson <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
At shutdown if you've got a _properly_ coded DRM modeset driver then
you'll get these two warnings at shutdown time:
Skipping disable of already disabled panel
Skipping unprepare of already unprepared panel
These warnings are ugly and sound concerning, but they're actually a
sign of a properly working system. That's not great.
We're not ready to get rid of the calls to drm_panel_disable() and
drm_panel_unprepare() because we're not 100% convinced that all DRM
modeset drivers are properly calling drm_atomic_helper_shutdown() or
drm_helper_force_disable_all() at the right times. However, having the
warning show up for correctly working systems is bad.
As a bit of a workaround, add some "if" tests to try to avoid the
warning on correctly working systems. Also add some comments and
update the TODO items in the hopes that future developers won't be too
confused by what's going on here.
Suggested-by: Daniel Vetter <[email protected]>
Acked-by: Neil Armstrong <[email protected]>
Reviewed-by: Linus Walleij <[email protected]>
Signed-off-by: Douglas Anderson <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/20240621134427.1.Ieb287c2c3ee3f6d3b0d5f49b29f746b93621749c@changeid
|
|
When the kmsg_dumper callback parameter changed, the reason variable
in mtdoops_do_dump() was not updated accordingly.
This breaks the build with mtdoops.
Fixes: e1a261ba599e ("printk: Add a short description string to kmsg_dump()")
Suggested-by: Knop Ryszard <[email protected]>
Signed-off-by: Jocelyn Falempe <[email protected]>
Acked-by: Richard Weinberger <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Panic_cpu is not exported, so it can't be used if fbcon is used as
a module. Use oops_in_progress in this case, but non-fatal oops won't
be printed.
Reported-by: kernel test robot <[email protected]>
Closes: https://lore.kernel.org/oe-kbuild-all/[email protected]/
Signed-off-by: Jocelyn Falempe <[email protected]>
Reviewed-by: Daniel Vetter <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
The Samsung ATNA45AF01 panel is an AMOLED eDP panel that has backlight
control over the DP AUX channel. While it works almost correctly with the
generic "edp-panel" compatible, the backlight needs special handling to
work correctly. It is similar to the existing ATNA33XC20 panel, just with
a larger resolution and size.
Add a new "samsung,atna45af01" compatible to describe this panel in the DT.
Use the existing "samsung,atna33xc20" as fallback compatible since existing
drivers should work as-is, given that resolution and size are discoverable
through the eDP link.
Signed-off-by: Stephan Gerhold <[email protected]>
Acked-by: Conor Dooley <[email protected]>
Reviewed-by: Neil Armstrong <[email protected]>
Reviewed-by: Douglas Anderson <[email protected]>
Signed-off-by: Douglas Anderson <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
https://gitlab.freedesktop.org/agd5f/linux into drm-next
amd-drm-fixes-6.11-2024-07-18:
amdgpu:
- Bump driver version for GFX12 DCC
- DC documention warning fixes
- VCN unified queue power fix
- SMU fix
- RAS fix
- Display corruption fix
Signed-off-by: Dave Airlie <[email protected]>
From: Alex Deucher <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
https://gitlab.freedesktop.org/drm/misc/kernel into drm-next
Two fixes for v3d to fix an array indexing on newer V3D revisions.
Signed-off-by: Dave Airlie <[email protected]>
From: Maxime Ripard <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/20240719-emerald-newt-of-skill-89b54a@houat
|
|
https://gitlab.freedesktop.org/drm/xe/kernel into drm-next
- Xe_exec ioctl minor fix on sync entry cleanup upon error (Ashutosh)
- SRIOV: limit VF LMEM provisioning (Michal)
- Wedge mode fixes (Brost)
Signed-off-by: Dave Airlie <[email protected]>
From: Rodrigo Vivi <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
https://gitlab.freedesktop.org/drm/i915/kernel into drm-next
- Reset intel_dp->link_trained before retraining the link [dp] (Imre Deak)
- Don't switch the LTTPR mode on an active link [dp] (Imre Deak)
Signed-off-by: Dave Airlie <[email protected]>
From: Tvrtko Ursulin <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/ZpjgtowjpUZoHvrl@linux
|
|
This breaks build if DRM_PANIC is not enabled.
Also add the missing include drm_crtc_internal.h in drm_panic.c
Fixes: 9f774c42a908 ("drm/panic: Add drm_panic_is_enabled()")
Signed-off-by: Jocelyn Falempe <[email protected]>
Reviewed-by: Michal Wajdeczko <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
The added lvds driver and a change in the dsi driver resulted in failed
builds when COMMON_CLK is disabled:
x86_64-linux-ld: drivers/gpu/drm/stm/dw_mipi_dsi-stm.o: in function `dw_mipi_dsi_stm_remove':
dw_mipi_dsi-stm.c:(.text+0x51e): undefined reference to `clk_hw_unregister'
x86_64-linux-ld: drivers/gpu/drm/stm/lvds.o: in function `lvds_remove':
lvds.c:(.text+0xe3): undefined reference to `of_clk_del_provider'
x86_64-linux-ld: lvds.c:(.text+0xec): undefined reference to `clk_hw_unregister'
x86_64-linux-ld: drivers/gpu/drm/stm/lvds.o: in function `lvds_pll_config':
lvds.c:(.text+0xb5d): undefined reference to `clk_hw_get_rate'
x86_64-linux-ld: drivers/gpu/drm/stm/lvds.o: in function `lvds_probe':
lvds.c:(.text+0x1476): undefined reference to `clk_hw_register'
x86_64-linux-ld: lvds.c:(.text+0x148b): undefined reference to `of_clk_hw_simple_get'
x86_64-linux-ld: lvds.c:(.text+0x1493): undefined reference to `of_clk_add_hw_provider'
x86_64-linux-ld: lvds.c:(.text+0x1535): undefined reference to `clk_hw_unregister'
Add this as a dependency for the stm driver itself, since it will be
required in practice anyway.
Fixes: 185f99b61442 ("drm/stm: dsi: expose DSI PHY internal clock")
Fixes: aca1cbc1c986 ("drm/stm: lvds: add new STM32 LVDS Display Interface Transmitter driver")
Signed-off-by: Arnd Bergmann <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Signed-off-by: Raphael Gallais-Pou <[email protected]>
|
|
Now that fbcon has the skip_panic option, there is no more conflicts
between drm_panic and fbcon.
Remove the build time dependency, so they can be both enabled.
Signed-off-by: Jocelyn Falempe <[email protected]>
Reviewed-by: Javier Martinez Canillas <[email protected]>
Reviewed-by: Daniel Vetter <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
fb_info->skip_panic flag prevents fbcon from writing to the
framebuffer during a kernel panic. So set it when the drm driver
implements drm panic, to avoid overwriting the panic screen.
Signed-off-by: Jocelyn Falempe <[email protected]>
Reviewed-by: Javier Martinez Canillas <[email protected]>
Reviewed-by: Daniel Vetter <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
This is required to avoid conflict between DRM_PANIC, and fbcon. If
a drm device already handle panic with drm_panic, it should set
the skip_panic field in fb_info, so that fbcon will stay quiet, and
not overwrite the panic_screen.
Signed-off-by: Jocelyn Falempe <[email protected]>
Reviewed-by: Javier Martinez Canillas <[email protected]>
Reviewed-by: Daniel Vetter <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
It allows to check if the drm device supports drm_panic.
Prepare the work to have better integration with fbcon and vtconsole.
Signed-off-by: Jocelyn Falempe <[email protected]>
Reviewed-by: Javier Martinez Canillas <[email protected]>
Reviewed-by: Daniel Vetter <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
The reload interrupt is not used by the driver. To avoid
unnecessary calls of the interrupt routine, don't enable it.
Solve small typo and add mask to simplify the driver.
Signed-off-by: Yannick Fertre <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Signed-off-by: Raphael Gallais-Pou <[email protected]>
|
|
The purpose of this mask is to simplify writing to the lxcr
register and not to forget any fields.
Signed-off-by: Yannick Fertre <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Signed-off-by: Raphael Gallais-Pou <[email protected]>
|
|
The plane's opacity should be reseted while the plane
is disabled. It prevents from seeing a possible global
or layer background color set earlier.
Signed-off-by: Yannick Fertre <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Signed-off-by: Raphael Gallais-Pou <[email protected]>
|
|
Implement struct drm_crtc_funcs.get_vblank_timestamp with the DRM
helper drm_crtc_vblank_helper_get_vblank_timestamp() with its helper
get_scanout_position. Read the scanout position from the MGAREG_VCOUNT
register.
Signed-off-by: Thomas Zimmermann <[email protected]>
Reviewed-by: Jocelyn Falempe <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|