aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2013-06-07hwmon: (adm1021) Strengthen chip detection for ADM1021, LM84 and MAX1617Guenter Roeck1-8/+50
On a system with both MAX1617 and JC42 sensors, JC42 sensors can be misdetected as LM84. Strengthen detection sufficiently enough to avoid this misdetection. Also improve detection for ADM1021. Modeled after chip detection code in sensors-detect command. Cc: [email protected] Signed-off-by: Guenter Roeck <[email protected]> Tested-by: Jean Delvare <[email protected]> Acked-by: Jean Delvare <[email protected]>
2013-06-07ASoC: tlv320aic3x: Remove deadlock from snd_soc_dapm_put_volsw_aic3x()Andreas Irestål1-5/+5
When calling snd_soc_dapm_sync(), it eventually tries to lock the same mutex already locked in snd_soc_dapm_put_volsw_aic3x() and a deadlock occurs. By moving the mutex unlock to just before snd_soc_dapm_sync(), this deadlock is prevented. This problem was introduced in Linux 3.5 Signed-off-by: Andreas Irestål <[email protected]> Signed-off-by: Mark Brown <[email protected]>
2013-06-07netfilter: nfnetlink_queue: fix missing HW protocolPablo Neira Ayuso1-3/+3
Locally generated IPv4 and IPv6 traffic gets skb->protocol unset, thus passing zero. ip6tables -I OUTPUT -j NFQUEUE libmnl/examples/netfilter# ./nf-queue 0 & ping6 ::1 packet received (id=1 hw=0x0000 hook=3) ^^^^^^ Signed-off-by: Pablo Neira Ayuso <[email protected]>
2013-06-07ncpfs: fix rmdir returns Device or resource busyDave Chiluk1-9/+0
1d2ef5901483004d74947bbf78d5146c24038fe7 caused a regression in ncpfs such that directories could no longer be removed. This was because ncp_rmdir checked to see if a dentry could be unhashed before allowing it to be removed. Since 1d2ef5901483004d74947bbf78d5146c24038fe7 introduced a change that incremented dentry->d_count causing it to always be greater than 1 unhash would always fail. Thus causing the error path in ncp_rmdir to always be taken. Removing this error path is safe as unhashing is still accomplished by calls to dput from vfs_rmdir. Signed-off-by: Dave Chiluk <[email protected]> Signed-off-by: Petr Vandrovec <[email protected]> Signed-off-by: Al Viro <[email protected]>
2013-06-07ASoC: dapm: Treat DAI widgets like AIF widgets for powerMark Brown3-25/+34
Even though they are virtual widgets DAI widgets still get counted for the DAPM context power management so we can't just use the active state to check if they should be powered as they may not be part of a complete path. Instead split them into input and output widgets and do the same power checks as we perform on AIFs. Reported-by: Stephen Warren <[email protected]> Tested-by: Stephen Warren <[email protected]> Signed-off-by: Mark Brown <[email protected]>
2013-06-07Merge branch 'pm-fixes'Rafael J. Wysocki3-4/+8
* pm-fixes: cpufreq: cpufreq-cpu0: use the exact frequency for clk_set_rate() cpufreq: protect 'policy->cpus' from offlining during __gov_queue_work() acpi-cpufreq: set current frequency based on target P-State
2013-06-07Merge branch 'acpi-fixes'Rafael J. Wysocki5-8/+31
* acpi-fixes: ACPI / PM: Do not execute _PS0 for devices without _PSC during initialization ACPI / scan: do not match drivers against objects having scan handlers ACPI / APEI: fix error return code in ghes_probe() ACPI / video: ignore BIOS initial backlight value for HP Pavilion g6 ACPI / video: ignore BIOS initial backlight value for HP m4 x86 / platform / hp_wmi: Fix bluetooth_rfkill misuse in hp_wmi_rfkill_setup()
2013-06-07ACPI / PM: Do not execute _PS0 for devices without _PSC during initializationRafael J. Wysocki1-4/+6
Commit b378549 (ACPI / PM: Do not power manage devices in unknown initial states) added code to force devices without _PSC, but having _PS0 defined in the ACPI namespace, into ACPI power state D0 by executing _PS0 for them. That turned out to break Toshiba P870-303, however, so revert that code. References: https://bugzilla.kernel.org/show_bug.cgi?id=58201 Reported-and-tested-by: Jerome Cantenot <[email protected]> Tracked-down-by: Lan Tianyu <[email protected]> Cc: 3.9+ <[email protected]> Signed-off-by: Rafael J. Wysocki <[email protected]>
2013-06-06clk: remove notifier from list before freeing itLai Jiangshan1-0/+1
The @cn is stay in @clk_notifier_list after it is freed, it cause memory corruption. Example, if @clk is registered(first), unregistered(first), registered(second), unregistered(second). The freed @cn will be used when @clk is registered(second), and the bug will be happened when @clk is unregistered(second): [ 517.040000] clk_notif_dbg clk_notif_dbg.1: clk_notifier_unregister() [ 517.040000] Unable to handle kernel paging request at virtual address 00df3008 [ 517.050000] pgd = ed858000 [ 517.050000] [00df3008] *pgd=00000000 [ 517.060000] Internal error: Oops: 5 [#1] PREEMPT SMP ARM [ 517.060000] Modules linked in: clk_notif_dbg(O-) [last unloaded: clk_notif_dbg] [ 517.060000] CPU: 1 PID: 499 Comm: modprobe Tainted: G O 3.10.0-rc3-00119-ga93cb29-dirty #85 [ 517.060000] task: ee1e0180 ti: ee3e6000 task.ti: ee3e6000 [ 517.060000] PC is at srcu_readers_seq_idx+0x48/0x84 [ 517.060000] LR is at srcu_readers_seq_idx+0x60/0x84 [ 517.060000] pc : [<c0052720>] lr : [<c0052738>] psr: 80070013 [ 517.060000] sp : ee3e7d48 ip : 00000000 fp : ee3e7d6c [ 517.060000] r10: 00000000 r9 : ee3e6000 r8 : 00000000 [ 517.060000] r7 : ed84fe4c r6 : c068ec90 r5 : c068e430 r4 : 00000000 [ 517.060000] r3 : 00df3000 r2 : 00000000 r1 : 00000002 r0 : 00000000 [ 517.060000] Flags: Nzcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user [ 517.060000] Control: 18c5387d Table: 2d85804a DAC: 00000015 [ 517.060000] Process modprobe (pid: 499, stack limit = 0xee3e6238) [ 517.060000] Stack: (0xee3e7d48 to 0xee3e8000) .... [ 517.060000] [<c0052720>] (srcu_readers_seq_idx+0x48/0x84) from [<c0052790>] (try_check_zero+0x34/0xfc) [ 517.060000] [<c0052790>] (try_check_zero+0x34/0xfc) from [<c00528b0>] (srcu_advance_batches+0x58/0x114) [ 517.060000] [<c00528b0>] (srcu_advance_batches+0x58/0x114) from [<c0052c30>] (__synchronize_srcu+0x114/0x1ac) [ 517.060000] [<c0052c30>] (__synchronize_srcu+0x114/0x1ac) from [<c0052d14>] (synchronize_srcu+0x2c/0x34) [ 517.060000] [<c0052d14>] (synchronize_srcu+0x2c/0x34) from [<c0053a08>] (srcu_notifier_chain_unregister+0x68/0x74) [ 517.060000] [<c0053a08>] (srcu_notifier_chain_unregister+0x68/0x74) from [<c0375a78>] (clk_notifier_unregister+0x7c/0xc0) [ 517.060000] [<c0375a78>] (clk_notifier_unregister+0x7c/0xc0) from [<bf008034>] (clk_notif_dbg_remove+0x34/0x9c [clk_notif_dbg]) [ 517.060000] [<bf008034>] (clk_notif_dbg_remove+0x34/0x9c [clk_notif_dbg]) from [<c02bb974>] (platform_drv_remove+0x24/0x28) [ 517.060000] [<c02bb974>] (platform_drv_remove+0x24/0x28) from [<c02b9bf8>] (__device_release_driver+0x8c/0xd4) [ 517.060000] [<c02b9bf8>] (__device_release_driver+0x8c/0xd4) from [<c02ba680>] (driver_detach+0x9c/0xc4) [ 517.060000] [<c02ba680>] (driver_detach+0x9c/0xc4) from [<c02b99c4>] (bus_remove_driver+0xcc/0xfc) [ 517.060000] [<c02b99c4>] (bus_remove_driver+0xcc/0xfc) from [<c02bace4>] (driver_unregister+0x54/0x78) [ 517.060000] [<c02bace4>] (driver_unregister+0x54/0x78) from [<c02bbb44>] (platform_driver_unregister+0x1c/0x20) [ 517.060000] [<c02bbb44>] (platform_driver_unregister+0x1c/0x20) from [<bf0081f8>] (clk_notif_dbg_driver_exit+0x14/0x1c [clk_notif_dbg]) [ 517.060000] [<bf0081f8>] (clk_notif_dbg_driver_exit+0x14/0x1c [clk_notif_dbg]) from [<c00835e4>] (SyS_delete_module+0x200/0x28c) [ 517.060000] [<c00835e4>] (SyS_delete_module+0x200/0x28c) from [<c000edc0>] (ret_fast_syscall+0x0/0x48) [ 517.060000] Code: e5973004 e7911102 e0833001 e2881002 (e7933101) Cc: [email protected] Reported-by: Sören Brinkmann <[email protected]> Signed-off-by: Lai Jiangshan <[email protected]> Tested-by: Sören Brinkmann <[email protected]> Signed-off-by: Mike Turquette <[email protected]> [[email protected]: shortened $SUBJECT]
2013-06-06Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds3-41/+47
Pull networking fix from David Miller: "This is a quick one commit pull request to cure the regression introduced by the MSG_CMSG_COMPAT change." (Background: commit 1be374a0518a completely broke 32-bit COMPAT handling by not only disallowing MSG_CMSG_COMPAT from user APIs, but clearing it in our own internal use too!) * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: net: Unbreak compat_sys_{send,recv}msg
2013-06-06Merge tag 'staging-3.10-rc4' of ↵Linus Torvalds8-15/+21
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging Pull staging driver fixes from Greg Kroah-Hartman: "Here are some staging and IIO driver fixes for the 3.10-rc5 release. All of them are tiny, and fix a number of reported issues (build and runtime)" Signed-off-by: Greg Kroah-Hartman <[email protected]> * tag 'staging-3.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: iio:inkern: Fix typo/bug in convert raw to processed. iio: frequency: ad4350: Fix bug / typo in mask inkern: iio_device_put after incorrect return/goto staging: alarm-dev: information leak in alarm_compat_ioctl() iio:callback buffer: free the scan_mask staging: alarm-dev: information leak in alarm_ioctl() drivers: staging: zcache: fix compile error staging: dwc2: fix value of dma_mask
2013-06-06Merge tag 'tty-3.10-rc4' of ↵Linus Torvalds3-7/+22
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty Pull tty/serial driver fixes from Greg Kroah-Hartman: "Here are some small bugfixes, and one revert, of serial driver issues that have been reported" * tag 'tty-3.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: Revert "serial: 8250: Make SERIAL_8250_RUNTIME_UARTS work correctly" serial: samsung: enable clock before clearing pending interrupts during init serial/imx: disable hardware flow control at startup
2013-06-06Merge tag 'usb-3.10-rc4' of ↵Linus Torvalds24-106/+187
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb Pull USB fixes from Greg Kroah-Hartman: "Here are a number of USB bugfixes and new device ids for the 3.10-rc5 tree. Nothing major here, a number of new device ids (and movement from the option to the zte_ev driver of a number of ids that we had previously gotten wrong, some xhci bugfixes, some usb-serial driver fixes that were recently found, some host controller fixes / reverts, and a variety of smaller other things" * tag 'usb-3.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (29 commits) USB: option,zte_ev: move most ZTE CDMA devices to zte_ev USB: option: blacklist network interface on Huawei E1820 USB: whiteheat: fix broken port configuration USB: serial: fix TIOCMIWAIT return value USB: mos7720: fix hardware flow control USB: keyspan: remove unused endpoint-array access USB: keyspan: fix bogus array index USB: zte_ev: fix broken open USB: serial: Add Option GTM681W to qcserial device table. USB: Serial: cypress_M8: Enable FRWD Dongle hidcom device USB: EHCI: fix regression related to qh_refresh() usbfs: Increase arbitrary limit for USB 3 isopkt length USB: zte_ev: fix control-message timeouts USB: mos7720: fix message timeouts USB: iuu_phoenix: fix bulk-message timeout USB: ark3116: fix control-message timeout USB: mos7840: fix DMA to stack USB: mos7720: fix DMA to stack USB: visor: fix initialisation of Treo/Kyocera devices USB: serial: fix Treo/Kyocera interrrupt-in urb context ...
2013-06-06Merge tag 'pci-v3.10-fixes-3' of ↵Linus Torvalds1-1/+4
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci Pull PCI fixes from Bjorn Helgaas: "This fixes a crash when booting a 32-bit kernel via the EFI boot stub. PCI ROM from EFI x86/PCI: Map PCI setup data with ioremap() so it can be in highmem" * tag 'pci-v3.10-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: x86/PCI: Map PCI setup data with ioremap() so it can be in highmem
2013-06-06Merge tag 'for-linus-v3.10-rc5' of git://oss.sgi.com/xfs/xfsLinus Torvalds10-59/+198
Pull more xfs updates from Ben Myers: "Here are several fixes for filesystems with CRC support turned on: fixes for quota, remote attributes, and recovery. There is also some feature work related to CRCs: the implementation of CRCs for the inode unlinked lists, disabling noattr2/attr2 options when appropriate, and bumping the maximum number of ACLs. I would have preferred to defer this last category of items to 3.11. This would require setting a feature bit for the on-disk changes, so there is some pressure to get these in 3.10. I believe this represents the end of the CRC related queue. - Rework of dquot CRCs - Fix for remote attribute invalidation of a leaf - Fix ordering of transaction replay in recovery - Implement CRCs for inode unlinked list - Disable noattr2/attr2 mount options when CRCs are enabled - Bump the limitation of ACL entries for v5 superblocks" * tag 'for-linus-v3.10-rc5' of git://oss.sgi.com/xfs/xfs: xfs: increase number of ACL entries for V5 superblocks xfs: disable noattr2/attr2 mount options for CRC enabled filesystems xfs: inode unlinked list needs to recalculate the inode CRC xfs: fix log recovery transaction item reordering xfs: fix remote attribute invalidation for a leaf xfs: rework dquot CRCs
2013-06-06arm: mvebu: armada-xp-{gp,openblocks-ax3-4}: specify PCIe rangeThomas Petazzoni2-4/+6
The ranges DT entry needed by the PCIe controller is defined at the SoC .dtsi level. However, some boards have a NOR flash, and to support it, they need to override the SoC-level ranges property to add an additional range. Since PCIe and NOR support came separately, some boards were not properly changed to include the PCIe range in their ranges property at the .dts level. This commit fixes those platforms. Signed-off-by: Thomas Petazzoni <[email protected]> Signed-off-by: Jason Cooper <[email protected]>
2013-06-06net: Unbreak compat_sys_{send,recv}msgAndy Lutomirski3-41/+47
I broke them in this commit: commit 1be374a0518a288147c6a7398792583200a67261 Author: Andy Lutomirski <[email protected]> Date: Wed May 22 14:07:44 2013 -0700 net: Block MSG_CMSG_COMPAT in send(m)msg and recv(m)msg This patch adds __sys_sendmsg and __sys_sendmsg as common helpers that accept MSG_CMSG_COMPAT and blocks MSG_CMSG_COMPAT at the syscall entrypoints. It also reverts some unnecessary checks in sys_socketcall. Apparently I was suffering from underscore blindness the first time around. Signed-off-by: Andy Lutomirski <[email protected]> Tested-by: Eric Dumazet <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2013-06-06ARM: Kirkwood: handle mv88f6282 cpu in __kirkwood_variant().Nicolas Schichan1-2/+3
MPP_F6281_MASK would be previously be returned when on mv88f6282, which would disallow some valid MPP configurations. Commit 830f8b91 (arm: plat-orion: fix printing of "MPP config unavailable on this hardware") made this problem visible as an invalid MPP configuration is now correctly detected and not applied. Signed-off-by: Nicolas Schichan <[email protected]> Cc: <[email protected]> # v3.9.x Signed-off-by: Jason Cooper <[email protected]>
2013-06-06tracing: Use current_uid() for critical time tracingSteven Rostedt (Red Hat)1-1/+9
The irqsoff tracer records the max time that interrupts are disabled. There are hooks in the assembly code that calls back into the tracer when interrupts are disabled or enabled. When they are enabled, the tracer checks if the amount of time they were disabled is larger than the previous recorded max interrupts off time. If it is, it creates a snapshot of the currently running trace to store where the last largest interrupts off time was held and how it happened. During testing, this RCU lockdep dump appeared: [ 1257.829021] =============================== [ 1257.829021] [ INFO: suspicious RCU usage. ] [ 1257.829021] 3.10.0-rc1-test+ #171 Tainted: G W [ 1257.829021] ------------------------------- [ 1257.829021] /home/rostedt/work/git/linux-trace.git/include/linux/rcupdate.h:780 rcu_read_lock() used illegally while idle! [ 1257.829021] [ 1257.829021] other info that might help us debug this: [ 1257.829021] [ 1257.829021] [ 1257.829021] RCU used illegally from idle CPU! [ 1257.829021] rcu_scheduler_active = 1, debug_locks = 0 [ 1257.829021] RCU used illegally from extended quiescent state! [ 1257.829021] 2 locks held by trace-cmd/4831: [ 1257.829021] #0: (max_trace_lock){......}, at: [<ffffffff810e2b77>] stop_critical_timing+0x1a3/0x209 [ 1257.829021] #1: (rcu_read_lock){.+.+..}, at: [<ffffffff810dae5a>] __update_max_tr+0x88/0x1ee [ 1257.829021] [ 1257.829021] stack backtrace: [ 1257.829021] CPU: 3 PID: 4831 Comm: trace-cmd Tainted: G W 3.10.0-rc1-test+ #171 [ 1257.829021] Hardware name: To Be Filled By O.E.M. To Be Filled By O.E.M./To be filled by O.E.M., BIOS SDBLI944.86P 05/08/2007 [ 1257.829021] 0000000000000001 ffff880065f49da8 ffffffff8153dd2b ffff880065f49dd8 [ 1257.829021] ffffffff81092a00 ffff88006bd78680 ffff88007add7500 0000000000000003 [ 1257.829021] ffff88006bd78680 ffff880065f49e18 ffffffff810daebf ffffffff810dae5a [ 1257.829021] Call Trace: [ 1257.829021] [<ffffffff8153dd2b>] dump_stack+0x19/0x1b [ 1257.829021] [<ffffffff81092a00>] lockdep_rcu_suspicious+0x109/0x112 [ 1257.829021] [<ffffffff810daebf>] __update_max_tr+0xed/0x1ee [ 1257.829021] [<ffffffff810dae5a>] ? __update_max_tr+0x88/0x1ee [ 1257.829021] [<ffffffff811002b9>] ? user_enter+0xfd/0x107 [ 1257.829021] [<ffffffff810dbf85>] update_max_tr_single+0x11d/0x12d [ 1257.829021] [<ffffffff811002b9>] ? user_enter+0xfd/0x107 [ 1257.829021] [<ffffffff810e2b15>] stop_critical_timing+0x141/0x209 [ 1257.829021] [<ffffffff8109569a>] ? trace_hardirqs_on+0xd/0xf [ 1257.829021] [<ffffffff811002b9>] ? user_enter+0xfd/0x107 [ 1257.829021] [<ffffffff810e3057>] time_hardirqs_on+0x2a/0x2f [ 1257.829021] [<ffffffff811002b9>] ? user_enter+0xfd/0x107 [ 1257.829021] [<ffffffff8109550c>] trace_hardirqs_on_caller+0x16/0x197 [ 1257.829021] [<ffffffff8109569a>] trace_hardirqs_on+0xd/0xf [ 1257.829021] [<ffffffff811002b9>] user_enter+0xfd/0x107 [ 1257.829021] [<ffffffff810029b4>] do_notify_resume+0x92/0x97 [ 1257.829021] [<ffffffff8154bdca>] int_signal+0x12/0x17 What happened was entering into the user code, the interrupts were enabled and a max interrupts off was recorded. The trace buffer was saved along with various information about the task: comm, pid, uid, priority, etc. The uid is recorded with task_uid(tsk). But this is a macro that uses rcu_read_lock() to retrieve the data, and this happened to happen where RCU is blind (user_enter). As only the preempt and irqs off tracers can have this happen, and they both only have the tsk == current, if tsk == current, use current_uid() instead of task_uid(), as current_uid() does not use RCU as only current can change its uid. This fixes the RCU suspicious splat. Signed-off-by: Steven Rostedt <[email protected]>
2013-06-06USB: option,zte_ev: move most ZTE CDMA devices to zte_evDan Williams2-26/+22
Per some ZTE Linux drivers I found for the AC2716, the following patch moves most ZTE CDMA devices from option to zte_ev. The blacklist stuff that option does is not required with zte_ev, because it doesn't implement any of the send_setup hooks which the blacklist suppressed. I did not move the 2718 over because I could not find any ZTE Linux drivers for that device, nor even any Windows drivers. Signed-off-by: Dan Williams <[email protected]> Cc: stable <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2013-06-06USB: option: blacklist network interface on Huawei E1820Bjørn Mork1-0/+2
The mode used by Windows for the Huawei E1820 will use the same ff/ff/ff class codes for both serial and network functions. Reported-by: Graham Inggs <[email protected]> Signed-off-by: Bjørn Mork <[email protected]> Cc: stable <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2013-06-06USB: whiteheat: fix broken port configurationJohan Hovold1-1/+1
When configuring the port (e.g. set_termios) the port minor number rather than the port number was used in the request (and they only coincide for minor number 0). Cc: [email protected] Signed-off-by: Johan Hovold <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2013-06-06xfs: increase number of ACL entries for V5 superblocksDave Chinner2-20/+42
The limit of 25 ACL entries is arbitrary, but baked into the on-disk format. For version 5 superblocks, increase it to the maximum nuber of ACLs that can fit into a single xattr. Signed-off-by: Dave Chinner <[email protected]> Reviewed-by: Brian Foster <[email protected]> Reviewed-by: Mark Tinguely <[email protected]> Signed-off-by: Ben Myers <[email protected]> (cherry picked from commit 5c87d4bc1a86bd6e6754ac3d6e111d776ddcfe57)
2013-06-06xfs: disable noattr2/attr2 mount options for CRC enabled filesystemsDave Chinner2-0/+14
attr2 format is always enabled for v5 superblock filesystems, so the mount options to enable or disable it need to be cause mount errors. Signed-off-by: Dave Chinner <[email protected]> Reviewed-by: Brian Foster <[email protected]> Signed-off-by: Ben Myers <[email protected]> (cherry picked from commit d3eaace84e40bf946129e516dcbd617173c1cf14)
2013-06-06xfs: inode unlinked list needs to recalculate the inode CRCDave Chinner2-0/+25
The inode unlinked list manipulations operate directly on the inode buffer, and so bypass the inode CRC calculation mechanisms. Hence an inode on the unlinked list has an invalid CRC. Fix this by recalculating the CRC whenever we modify an unlinked list pointer in an inode, ncluding during log recovery. This is trivial to do and results in unlinked list operations always leaving a consistent inode in the buffer. Signed-off-by: Dave Chinner <[email protected]> Reviewed-by: Mark Tinguely <[email protected]> Signed-off-by: Ben Myers <[email protected]> (cherry picked from commit 0a32c26e720a8b38971d0685976f4a7d63f9e2ef)
2013-06-06xfs: fix log recovery transaction item reorderingDave Chinner1-7/+58
There are several constraints that inode allocation and unlink logging impose on log recovery. These all stem from the fact that inode alloc/unlink are logged in buffers, but all other inode changes are logged in inode items. Hence there are ordering constraints that recovery must follow to ensure the correct result occurs. As it turns out, this ordering has been working mostly by chance than good management. The existing code moves all buffers except cancelled buffers to the head of the list, and everything else to the tail of the list. The problem with this is that is interleaves inode items with the buffer cancellation items, and hence whether the inode item in an cancelled buffer gets replayed is essentially left to chance. Further, this ordering causes problems for log recovery when inode CRCs are enabled. It typically replays the inode unlink buffer long before it replays the inode core changes, and so the CRC recorded in an unlink buffer is going to be invalid and hence any attempt to validate the inode in the buffer is going to fail. Hence we really need to enforce the ordering that the inode alloc/unlink code has expected log recovery to have since inode chunk de-allocation was introduced back in 2003... Signed-off-by: Dave Chinner <[email protected]> Reviewed-by: Mark Tinguely <[email protected]> Signed-off-by: Ben Myers <[email protected]> (cherry picked from commit a775ad778073d55744ed6709ccede36310638911)
2013-06-06xfs: fix remote attribute invalidation for a leafDave Chinner1-1/+1
When invalidating an attribute leaf block block, there might be remote attributes that it points to. With the recent rework of the remote attribute format, we have to make sure we calculate the length of the attribute correctly. We aren't doing that in xfs_attr3_leaf_inactive(), so fix it. Signed-off-by: Dave Chinner <[email protected]> Reviewed-by: Brian Foster <[email protected]> Reviewed-by: Mark Tinguely <[email protected]> Signed-off-by: Ben Myers <[email protected]> (cherry picked from commit 59913f14dfe8eb772ff93eb442947451b4416329)
2013-06-06xfs: rework dquot CRCsDave Chinner4-31/+58
Calculating dquot CRCs when the backing buffer is written back just doesn't work reliably. There are several places which manipulate dquots directly in the buffers, and they don't calculate CRCs appropriately, nor do they always set the buffer up to calculate CRCs appropriately. Firstly, if we log a dquot buffer (e.g. during allocation) it gets logged without valid CRC, and so on recovery we end up with a dquot that is not valid. Secondly, if we recover/repair a dquot, we don't have a verifier attached to the buffer and hence CRCs are not calculated on the way down to disk. Thirdly, calculating the CRC after we've changed the contents means that if we re-read the dquot from the buffer, we cannot verify the contents of the dquot are valid, as the CRC is invalid. So, to avoid all the dquot CRC errors that are being detected by the read verifier, change to using the same model as for inodes. That is, dquot CRCs are calculated and written to the backing buffer at the time the dquot is flushed to the backing buffer. If we modify the dquot directly in the backing buffer, calculate the CRC immediately after the modification is complete. Hence the dquot in the on-disk buffer should always have a valid CRC. Signed-off-by: Dave Chinner <[email protected]> Reviewed-by: Brian Foster <[email protected]> Reviewed-by: Ben Myers <[email protected]> Signed-off-by: Ben Myers <[email protected]> (cherry picked from commit 6fcdc59de28817d1fbf1bd58cc01f4f3fac858fb)
2013-06-06ARM: omap3: clock: fix wrong container_of in clock36xx.cJean-Philippe Francois1-9/+9
omap36xx_pwrdn_clk_enable_with_hsdiv_restore expects the parent hw of the clock to be a clk_hw_omap. However, looking at cclock3xxx_data.c, all concerned clock have parent defined as clk_divider. Fix the function to use clk_divider. Tested with 3.9 on dm3730. Signed-off-by: Jean-Philippe François <[email protected]> Cc: NeilBrown <[email protected]> Cc: Mike Turquette <[email protected]> Signed-off-by: Paul Walmsley <[email protected]>
2013-06-06MIPS: ralink: add missing SZ_1M multiplierJohn Crispin1-1/+1
On RT5350 the memory size is set to Bytes and not MegaBytes due to a missing multiplier. Signed-off-by: John Crispin <[email protected]> Cc: John Crispin <[email protected]> Patchwork: https://patchwork.linux-mips.org/patch/5378/ Signed-off-by: Ralf Baechle <[email protected]>
2013-06-06MIPS: Compat: Fix cputime_to_timeval() arguments in compat binfmt_elf.Ralf Baechle2-0/+22
cputime_to_timeval() takes a struct timeval *as its second argument but a struct compat_timeval * will be passed resulting in: CC arch/mips/kernel/binfmt_elfn32.o In file included from arch/mips/kernel/binfmt_elfn32.c:122:0: arch/mips/kernel/../../../fs/binfmt_elf.c: In function ‘fill_prstatus’: arch/mips/kernel/../../../fs/binfmt_elf.c:1330:3: warning: passing argument 2 of ‘cputime_to_timeval’ from incompatible pointer type [enabled by default] In file included from include/asm-generic/cputime.h:12:0, from /home/ralf/src/linux/linux-mips/arch/mips/include/asm/cputime.h:4, from include/linux/sched.h:28, from include/linux/ptrace.h:5, from include/uapi/linux/elfcore.h:7, from include/linux/elfcore.h:7, from arch/mips/kernel/binfmt_elfn32.c:55: include/asm-generic/cputime_nsecs.h:92:91: note: expected ‘struct timeval *’ but argument is of type ‘struct compat_timeval *’ In file included from arch/mips/kernel/binfmt_elfn32.c:122:0: arch/mips/kernel/../../../fs/binfmt_elf.c:1331:3: warning: passing argument 2 of ‘cputime_to_timeval’ from incompatible pointer type [enabled by default] In file included from include/asm-generic/cputime.h:12:0, from /home/ralf/src/linux/linux-mips/arch/mips/include/asm/cputime.h:4, from include/linux/sched.h:28, from include/linux/ptrace.h:5, from include/uapi/linux/elfcore.h:7, from include/linux/elfcore.h:7, from arch/mips/kernel/binfmt_elfn32.c:55: include/asm-generic/cputime_nsecs.h:92:91: note: expected ‘struct timeval *’ but argument is of type ‘struct compat_timeval *’ In file included from arch/mips/kernel/binfmt_elfn32.c:122:0: arch/mips/kernel/../../../fs/binfmt_elf.c:1336:3: warning: passing argument 2 of ‘cputime_to_timeval’ from incompatible pointer type [enabled by default] In file included from include/asm-generic/cputime.h:12:0, from /home/ralf/src/linux/linux-mips/arch/mips/include/asm/cputime.h:4, from include/linux/sched.h:28, from include/linux/ptrace.h:5, from include/uapi/linux/elfcore.h:7, from include/linux/elfcore.h:7, from arch/mips/kernel/binfmt_elfn32.c:55: include/asm-generic/cputime_nsecs.h:92:91: note: expected ‘struct timeval *’ but argument is of type ‘struct compat_timeval *’ In file included from arch/mips/kernel/binfmt_elfn32.c:122:0: arch/mips/kernel/../../../fs/binfmt_elf.c:1337:3: warning: passing argument 2 of ‘cputime_to_timeval’ from incompatible pointer type [enabled by default] In file included from include/asm-generic/cputime.h:12:0, from /home/ralf/src/linux/linux-mips/arch/mips/include/asm/cputime.h:4, from include/linux/sched.h:28, from include/linux/ptrace.h:5, from include/uapi/linux/elfcore.h:7, from include/linux/elfcore.h:7, from arch/mips/kernel/binfmt_elfn32.c:55: include/asm-generic/cputime_nsecs.h:92:91: note: expected ‘struct timeval *’ but argument is of type ‘struct compat_timeval *’ In file included from arch/mips/kernel/binfmt_elfn32.c:122:0: arch/mips/kernel/../../../fs/binfmt_elf.c:1339:2: warning: passing argument 2 of ‘cputime_to_timeval’ from incompatible pointer type [enabled by default] In file included from include/asm-generic/cputime.h:12:0, from /home/ralf/src/linux/linux-mips/arch/mips/include/asm/cputime.h:4, from include/linux/sched.h:28, from include/linux/ptrace.h:5, from include/uapi/linux/elfcore.h:7, from include/linux/elfcore.h:7, from arch/mips/kernel/binfmt_elfn32.c:55: include/asm-generic/cputime_nsecs.h:92:91: note: expected ‘struct timeval *’ but argument is of type ‘struct compat_timeval *’ In file included from arch/mips/kernel/binfmt_elfn32.c:122:0: arch/mips/kernel/../../../fs/binfmt_elf.c:1340:2: warning: passing argument 2 of ‘cputime_to_timeval’ from incompatible pointer type [enabled by default] In file included from include/asm-generic/cputime.h:12:0, from /home/ralf/src/linux/linux-mips/arch/mips/include/asm/cputime.h:4, from include/linux/sched.h:28, from include/linux/ptrace.h:5, from include/uapi/linux/elfcore.h:7, from include/linux/elfcore.h:7, from arch/mips/kernel/binfmt_elfn32.c:55: include/asm-generic/cputime_nsecs.h:92:91: note: expected ‘struct timeval *’ but argument is of type ‘struct compat_timeval *’ AS arch/mips/kernel/scall64-n32.o CC arch/mips/kernel/signal_n32.o CC arch/mips/kernel/binfmt_elfo32.o In file included from arch/mips/kernel/binfmt_elfo32.c:165:0: arch/mips/kernel/../../../fs/binfmt_elf.c: In function ‘fill_prstatus’: arch/mips/kernel/../../../fs/binfmt_elf.c:1330:3: warning: passing argument 2 of ‘cputime_to_timeval’ from incompatible pointer type [enabled by default] In file included from include/asm-generic/cputime.h:12:0, from /home/ralf/src/linux/linux-mips/arch/mips/include/asm/cputime.h:4, from include/linux/sched.h:28, from include/linux/ptrace.h:5, from include/uapi/linux/elfcore.h:7, from include/linux/elfcore.h:7, from arch/mips/kernel/binfmt_elfo32.c:78: include/asm-generic/cputime_nsecs.h:92:91: note: expected ‘struct timeval *’ but argument is of type ‘struct compat_timeval *’ In file included from arch/mips/kernel/binfmt_elfo32.c:165:0: arch/mips/kernel/../../../fs/binfmt_elf.c:1331:3: warning: passing argument 2 of ‘cputime_to_timeval’ from incompatible pointer type [enabled by default] In file included from include/asm-generic/cputime.h:12:0, from /home/ralf/src/linux/linux-mips/arch/mips/include/asm/cputime.h:4, from include/linux/sched.h:28, from include/linux/ptrace.h:5, from include/uapi/linux/elfcore.h:7, from include/linux/elfcore.h:7, from arch/mips/kernel/binfmt_elfo32.c:78: include/asm-generic/cputime_nsecs.h:92:91: note: expected ‘struct timeval *’ but argument is of type ‘struct compat_timeval *’ In file included from arch/mips/kernel/binfmt_elfo32.c:165:0: arch/mips/kernel/../../../fs/binfmt_elf.c:1336:3: warning: passing argument 2 of ‘cputime_to_timeval’ from incompatible pointer type [enabled by default] In file included from include/asm-generic/cputime.h:12:0, from /home/ralf/src/linux/linux-mips/arch/mips/include/asm/cputime.h:4, from include/linux/sched.h:28, from include/linux/ptrace.h:5, from include/uapi/linux/elfcore.h:7, from include/linux/elfcore.h:7, from arch/mips/kernel/binfmt_elfo32.c:78: include/asm-generic/cputime_nsecs.h:92:91: note: expected ‘struct timeval *’ but argument is of type ‘struct compat_timeval *’ In file included from arch/mips/kernel/binfmt_elfo32.c:165:0: arch/mips/kernel/../../../fs/binfmt_elf.c:1337:3: warning: passing argument 2 of ‘cputime_to_timeval’ from incompatible pointer type [enabled by default] In file included from include/asm-generic/cputime.h:12:0, from /home/ralf/src/linux/linux-mips/arch/mips/include/asm/cputime.h:4, from include/linux/sched.h:28, from include/linux/ptrace.h:5, from include/uapi/linux/elfcore.h:7, from include/linux/elfcore.h:7, from arch/mips/kernel/binfmt_elfo32.c:78: include/asm-generic/cputime_nsecs.h:92:91: note: expected ‘struct timeval *’ but argument is of type ‘struct compat_timeval *’ In file included from arch/mips/kernel/binfmt_elfo32.c:165:0: arch/mips/kernel/../../../fs/binfmt_elf.c:1339:2: warning: passing argument 2 of ‘cputime_to_timeval’ from incompatible pointer type [enabled by default] In file included from include/asm-generic/cputime.h:12:0, from /home/ralf/src/linux/linux-mips/arch/mips/include/asm/cputime.h:4, from include/linux/sched.h:28, from include/linux/ptrace.h:5, from include/uapi/linux/elfcore.h:7, from include/linux/elfcore.h:7, from arch/mips/kernel/binfmt_elfo32.c:78: include/asm-generic/cputime_nsecs.h:92:91: note: expected ‘struct timeval *’ but argument is of type ‘struct compat_timeval *’ In file included from arch/mips/kernel/binfmt_elfo32.c:165:0: arch/mips/kernel/../../../fs/binfmt_elf.c:1340:2: warning: passing argument 2 of ‘cputime_to_timeval’ from incompatible pointer type [enabled by default] In file included from include/asm-generic/cputime.h:12:0, from /home/ralf/src/linux/linux-mips/arch/mips/include/asm/cputime.h:4, from include/linux/sched.h:28, from include/linux/ptrace.h:5, from include/uapi/linux/elfcore.h:7, from include/linux/elfcore.h:7, from arch/mips/kernel/binfmt_elfo32.c:78: include/asm-generic/cputime_nsecs.h:92:91: note: expected ‘struct timeval *’ but argument is of type ‘struct compat_timeval *’ Signed-off-by: Ralf Baechle <[email protected]>
2013-06-06MIPS: OCTEON: Improve _machine_halt implementation.David Daney1-6/+9
As noted by Wladislav Wiebe: $ halt .. Sent SIGKILL to all processes Requesting system halt [66.729373] System halted. [66.733244] [66.734761] ===================================== [66.739473] [ BUG: lock held at task exit time! ] [66.744188] 3.8.7-0-sampleversion-fct #49 Tainted: G O [66.750202] ------------------------------------- [66.754913] init/21479 is exiting with locks still held! [66.760234] 1 lock held by init/21479: [66.763990] #0: (reboot_mutex){+.+...}, at: [<ffffffff801776c8>] SyS_reboot+0xe0/0x218 [66.772165] [66.772165] stack backtrace: [66.776532] Call Trace: [66.778992] [<ffffffff805780a8>] dump_stack+0x8/0x34 [66.783972] [<ffffffff801618b0>] do_exit+0x610/0xa70 [66.788948] [<ffffffff801777a8>] SyS_reboot+0x1c0/0x218 [66.794186] [<ffffffff8013d6a4>] handle_sys64+0x44/0x64 This is an alternative fix to the one sent by Wladislav. We kill the watchdog for each CPU and then spin in WAIT with interrupts disabled. This is the lowest power mode for the OCTEON. If we were to spin with interrupts enabled, we would get a continual stream of warning messages and backtraces from the lockup detector, so I chose to disable interrupts. Signed-off-by: David Daney <[email protected]> Cc: Maxim Uvarov <[email protected]> Cc: Wladislav Wiebe <[email protected]> Cc: [email protected] Cc: David Daney <[email protected]> Patchwork: https://patchwork.linux-mips.org/patch/5324/ Signed-off-by: Ralf Baechle <[email protected]>
2013-06-06MIPS: rtlx: Fix implicit declaration of function set_vi_handler()Yoichi Yuasa1-0/+1
arch/mips/kernel/rtlx.c: In function 'rtlx_module_init': arch/mips/kernel/rtlx.c:523:3: error: implicit declaration of function 'set_vi_handler' [-Werror=implicit-function-declaration] Signed-off-by: Yoichi Yuasa <[email protected]> Cc: [email protected] Patchwork: https://patchwork.linux-mips.org/patch/5340/ Signed-off-by: Ralf Baechle <[email protected]>
2013-06-06arch, mm: Remove tlb_fast_mode()Peter Zijlstra4-81/+13
Since the introduction of preemptible mmu_gather TLB fast mode has been broken. TLB fast mode relies on there being absolutely no concurrency; it frees pages first and invalidates TLBs later. However now we can get concurrency and stuff goes *bang*. This patch removes all tlb_fast_mode() code; it was found the better option vs trying to patch the hole by entangling tlb invalidation with the scheduler. Cc: Thomas Gleixner <[email protected]> Cc: Russell King <[email protected]> Cc: Tony Luck <[email protected]> Reported-by: Max Filippov <[email protected]> Signed-off-by: Peter Zijlstra <[email protected]> Signed-off-by: Linus Torvalds <[email protected]>
2013-06-06Merge branch 'rc-fixes' of ↵Linus Torvalds5-12/+27
git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild Pull kbuild fixes from Michal Marek: "There is one fix for a kbuild regression, plus three kconfig fixes for bugs that have alway been there, but are simple enough to be fixed in an -rc" * 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild: kconfig/menu.c: fix multiple references to expressions in menu_add_prop() mconf: handle keys in empty dialogs kbuild: Don't assume dts files live in arch/*/boot/dts scripts/config: fix assignment of parameters for short version of --*-after options
2013-06-05ARM: 7747/1: pcpu: ensure __my_cpu_offset cannot be re-ordered across barrier()Will Deacon1-2/+9
__my_cpu_offset is non-volatile, since we want its value to be cached when we access several per-cpu variables in a row with preemption disabled. This means that we rely on preempt_{en,dis}able to hazard with the operation via the barrier() macro, so that we can't end up migrating CPUs without reloading the per-cpu offset. Unfortunately, GCC doesn't treat a "memory" clobber on a non-volatile asm block as a side-effect, and will happily re-order it before other memory clobbers (including those in prempt_disable()) and cache the value. This has been observed to break the cmpxchg logic in the slub allocator, leading to livelock in kmem_cache_alloc in mainline kernels. This patch adds a dummy memory input operand to __my_cpu_offset, forcing it to be ordered with respect to the barrier() macro. Cc: <[email protected]> Cc: Rob Herring <[email protected]> Reviewed-by: Nicolas Pitre <[email protected]> Signed-off-by: Will Deacon <[email protected]> Signed-off-by: Russell King <[email protected]>
2013-06-05ARM: 7750/1: update legacy CPU ID in decompressor cache support jump tableMarc C1-2/+2
The previous mask values for the legacy ARM CPU IDs were conflicting with the CPU ID assignments for late-generation CPUs (like the Qualcomm MSM/QSD or Broadcom Brahma-15 processors). This change corrects the legacy ARM CPU ID value so that the jump table can fall-through to the appropriate cache maintenance / MMU functions. Signed-off-by: Marc C <[email protected]> Signed-off-by: Russell King <[email protected]>
2013-06-05ARM: 7743/1: compressed/head.S: work around new binutils warningArnd Bergmann4-1/+4
In August 2012, Matthew Gretton-Dann checked a change into binutils labelled "Error on obsolete & warn on deprecated registers", apparently as part of ARMv8 support. Apparently, this was supposed to emit the message "Warning: This coprocessor register access is deprecated in ARMv8" when using certain mcr/mrc instructions and building for ARMv8. Unfortunately, the message that is actually emitted appears to be '(null)', which is less helpful in comparison. Even more unfortunately, this is biting us on every single kernel build with a new gas, because arch/arm/boot/compressed/head.S and some other files in that directory are built with -march=all since kernel commit 80cec14a8 "[ARM] Add -march=all to assembly file build in arch/arm/boot/compressed" back in v2.6.28. This patch reverts Russell's nice solution and instead marks the head.S file to be built for armv7-a, which fortunately lets us build all instructions in that file without warnings even on the broken binutils. Without this patch, building anything results in: arch/arm/boot/compressed/head.S: Assembler messages: arch/arm/boot/compressed/head.S:565: Warning: (null) arch/arm/boot/compressed/head.S:676: Warning: (null) arch/arm/boot/compressed/head.S:698: Warning: (null) arch/arm/boot/compressed/head.S:722: Warning: (null) arch/arm/boot/compressed/head.S:726: Warning: (null) arch/arm/boot/compressed/head.S:957: Warning: (null) arch/arm/boot/compressed/head.S:996: Warning: (null) arch/arm/boot/compressed/head.S:997: Warning: (null) arch/arm/boot/compressed/head.S:1027: Warning: (null) arch/arm/boot/compressed/head.S:1035: Warning: (null) arch/arm/boot/compressed/head.S:1046: Warning: (null) arch/arm/boot/compressed/head.S:1060: Warning: (null) arch/arm/boot/compressed/head.S:1092: Warning: (null) arch/arm/boot/compressed/head.S:1094: Warning: (null) arch/arm/boot/compressed/head.S:1095: Warning: (null) arch/arm/boot/compressed/head.S:1102: Warning: (null) arch/arm/boot/compressed/head.S:1134: Warning: (null) Signed-off-by: Arnd Bergmann <[email protected]> Cc: [email protected] Cc: Matthew Gretton-Dann <[email protected]> Signed-off-by: Russell King <[email protected]>
2013-06-05ARM: 7742/1: topology: export cpu_topologyArnd Bergmann1-0/+2
The cpu_topology symbol is required by any driver using the topology interfaces, which leads to a couple of build errors: ERROR: "cpu_topology" [drivers/net/ethernet/sfc/sfc.ko] undefined! ERROR: "cpu_topology" [drivers/cpufreq/arm_big_little.ko] undefined! ERROR: "cpu_topology" [drivers/block/mtip32xx/mtip32xx.ko] undefined! The obvious solution is to export this symbol. Signed-off-by: Arnd Bergmann <[email protected]> Acked-by: Will Deacon <[email protected]> Cc: [email protected] Cc: Nicolas Pitre <[email protected]> Cc: Vincent Guittot <[email protected]> Signed-off-by: Russell King <[email protected]>
2013-06-05ARM: 7737/1: fix kernel decompressor compilation error with ↵Nicolas Pitre1-0/+28
CONFIG_DEBUG_SEMIHOSTING Selecting this option produces: AS arch/arm/boot/compressed/debug.o arch/arm/boot/compressed/debug.S:4:33: fatal error: mach/debug-macro.S: No such file or directory compilation terminated. make[3]: *** [arch/arm/boot/compressed/debug.o] Error 1 The semihosting support cannot be modelled into a senduart macro as it requires memory space for argument passing. So the CONFIG_DEBUG_LL_INCLUDE may not have any sensible value and the include directive should be omitted. While at it, let's add proper semihosting output support to the decompressor. Signed-off-by: Nicolas Pitre <[email protected]> Acked-by: Shawn Guo <[email protected]> Signed-off-by: Russell King <[email protected]>
2013-06-05x86/PCI: Map PCI setup data with ioremap() so it can be in highmemMatt Fleming1-1/+4
f9a37be0f0 ("x86: Use PCI setup data") added support for using PCI ROM images from setup_data. This used phys_to_virt(), which is not valid for highmem addresses, and can cause a crash when booting a 32-bit kernel via the EFI boot stub. pcibios_add_device() assumes that the physical addresses stored in setup_data are accessible via the direct kernel mapping, and that calling phys_to_virt() is valid. This isn't guaranteed to be true on x86 where the direct mapping range is much smaller than on x86-64. Calling phys_to_virt() on a highmem address results in the following: BUG: unable to handle kernel paging request at 39a3c198 IP: [<c262be0f>] pcibios_add_device+0x2f/0x90 ... Call Trace: [<c2370c73>] pci_device_add+0xe3/0x130 [<c274640b>] pci_scan_single_device+0x8b/0xb0 [<c2370d08>] pci_scan_slot+0x48/0x100 [<c2371904>] pci_scan_child_bus+0x24/0xc0 [<c262a7b0>] pci_acpi_scan_root+0x2c0/0x490 [<c23b7203>] acpi_pci_root_add+0x312/0x42f ... The solution is to use ioremap() instead of phys_to_virt() to map the setup data into the kernel address space. [bhelgaas: changelog] Tested-by: Jani Nikula <[email protected]> Signed-off-by: Matt Fleming <[email protected]> Signed-off-by: Bjorn Helgaas <[email protected]> Cc: Matthew Garrett <[email protected]> Cc: Seth Forshee <[email protected]> Cc: Jesse Barnes <[email protected]> Cc: [email protected] # v3.8+
2013-06-05s390/sclp: fix new line detectionPeter Oberparleiter1-1/+1
When printing multi-line text using sclp_print, line endings are not correctly handled. The routine is expecting an EBCDIC new line character as line terminator while the input text is encoded in ASCII format. Fix this problem by modifying sclp_print to scan for ASCII new line characters. Signed-off-by: Peter Oberparleiter <[email protected]> Signed-off-by: Martin Schwidefsky <[email protected]>
2013-06-05s390/pgtable: make pgste lock an explicit barrierChristian Borntraeger1-2/+3
Getting and Releasing the pgste lock has lock semantics. Make the code an explicit barrier. Signed-off-by: Christian Borntraeger <[email protected]> Signed-off-by: Martin Schwidefsky <[email protected]>
2013-06-05s390/pgtable: Save pgste during modify_prot_start/commitChristian Borntraeger1-1/+10
In modify_prot_start we update the pgste value but never store it back into the original location. Lets save the calculated result, since modify_prot_commit will use the value of the pgste. Signed-off-by: Christian Borntraeger <[email protected]> Signed-off-by: Martin Schwidefsky <[email protected]>
2013-06-05s390/dumpstack: fix address ranges for asynchronous and panic stackMartin Schwidefsky1-4/+8
git commit dc7ee00d4771b321 "s390: lowcore stack pointer offsets" introduced a regression in regard to show_stack(). The stack pointer for the asynchronous and the panic stack in the lowcore now have an additional offset applied to them. This offset needs to be taken into account in the calculation for the low and high address for the stacks. Signed-off-by: Martin Schwidefsky <[email protected]>
2013-06-05s390/pgtable: Fix guest overindication for change bitChristian Borntraeger1-7/+9
When doing the transition invalid->valid in the host page table for a guest, then the guest view of C/R is in the pgste. After validation the view is pgste OR real key. We must zero out the real key C/R to avoid guest over-indication for change (and reference). Touching the real key is ok also for the host: The change bit is tracked via write protection and the reference bit is also ok because set_pte_at was called and the page will be touched anyway soon. Furthermore architecture defines reference as "substantially accurate", over- and underindication are ok. Signed-off-by: Christian Borntraeger <[email protected]> Signed-off-by: Martin Schwidefsky <[email protected]>
2013-06-05USB: serial: fix TIOCMIWAIT return valueJohan Hovold1-3/+1
Fix regression introduced by commit 143d9d9616 ("USB: serial: add tiocmiwait subdriver operation") which made the ioctl operation return ENODEV rather than ENOIOCTLCMD when a subdriver TIOCMIWAIT implementation is missing. Signed-off-by: Johan Hovold <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2013-06-05vfio: fix crash on rmmodAlexey Kardashevskiy1-1/+1
devtmpfs_delete_node() calls devnode() callback with mode==NULL but vfio still tries to write there. The patch fixes this. Signed-off-by: Alexey Kardashevskiy <[email protected]> Signed-off-by: Alex Williamson <[email protected]>
2013-06-05ASoC: arizona: Correct AEC loopback enableCharles Keepax2-2/+4
Signed-off-by: Charles Keepax <[email protected]> Signed-off-by: Mark Brown <[email protected]>
2013-06-05netfilter: xt_TCPMSS: Fix violation of RFC879 in absence of MSS optionPhil Oester1-0/+6
The clamp-mss-to-pmtu option of the xt_TCPMSS target can cause issues connecting to websites if there was no MSS option present in the original SYN packet from the client. In these cases, it may add a MSS higher than the default specified in RFC879. Fix this by never setting a value > 536 if no MSS option was specified by the client. This closes netfilter's bugzilla #662. Signed-off-by: Phil Oester <[email protected]> Signed-off-by: Pablo Neira Ayuso <[email protected]>
Powered by cgit, Gruvboxed by Blaster4385.