aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2021-06-02nvme-loop: reset queue count to 1 in nvme_loop_destroy_io_queues()Hannes Reinecke1-0/+1
The queue count is increased in nvme_loop_init_io_queues(), so we need to reset it to 1 at the end of nvme_loop_destroy_io_queues(). Otherwise the function is not re-entrant safe, and crash will happen during concurrent reset and remove calls. Signed-off-by: Hannes Reinecke <[email protected]> Reviewed-by: Chaitanya Kulkarni <[email protected]> Signed-off-by: Christoph Hellwig <[email protected]>
2021-06-01Merge remote-tracking branch 'riscv/riscv-wx-mappings' into fixesPalmer Dabbelt1-2/+6
This single commit is shared between fixes and for-next, as it fixes a concrete bug while likely conflicting with a more invasive cleanup to avoid these oddball mappings entirely. * riscv/riscv-wx-mappings: riscv: mm: Fix W+X mappings at boot
2021-06-01RISC-V: Fix memblock_free() usages in init_resources()Wende Tan1-2/+2
`memblock_free()` takes a physical address as its first argument. Fix the wrong usages in `init_resources()`. Fixes: ffe0e526126884cf036a6f724220f1f9b4094fd2 ("RISC-V: Improve init_resources()") Fixes: 797f0375dd2ef5cdc68ac23450cbae9a5c67a74e ("RISC-V: Do not allocate memblock while iterating reserved memblocks") Signed-off-by: Wende Tan <[email protected]> Signed-off-by: Palmer Dabbelt <[email protected]>
2021-06-01riscv: skip errata_cip_453.o if CONFIG_ERRATA_SIFIVE_CIP_453 is disabledVincent1-1/+1
The errata_cip_453.o should be built only when the Kconfig CONFIG_ERRATA_SIFIVE_CIP_453 is enabled. Reported-by: kernel test robot <[email protected]> Signed-off-by: Vincent <[email protected]> Fixes: 0e0d4992517f ("riscv: enable SiFive errata CIP-453 and CIP-1200 Kconfig only if CONFIG_64BIT=y") Signed-off-by: Palmer Dabbelt <[email protected]>
2021-06-01riscv: mm: Fix W+X mappings at bootJisheng Zhang1-2/+6
When the kernel mapping was moved the last 2GB of the address space, (__va(PFN_PHYS(max_low_pfn))) is much smaller than the .data section start address, the last set_memory_nx() in protect_kernel_text_data() will fail, thus the .data section is still mapped as W+X. This results in below W+X mapping waring at boot. Fix it by passing the correct .data section page num to the set_memory_nx(). [ 0.396516] ------------[ cut here ]------------ [ 0.396889] riscv/mm: Found insecure W+X mapping at address (____ptrval____)/0xffffffff80c00000 [ 0.398347] WARNING: CPU: 0 PID: 1 at arch/riscv/mm/ptdump.c:258 note_page+0x244/0x24a [ 0.398964] Modules linked in: [ 0.399459] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.13.0-rc1+ #14 [ 0.400003] Hardware name: riscv-virtio,qemu (DT) [ 0.400591] epc : note_page+0x244/0x24a [ 0.401368] ra : note_page+0x244/0x24a [ 0.401772] epc : ffffffff80007c86 ra : ffffffff80007c86 sp : ffffffe000e7bc30 [ 0.402304] gp : ffffffff80caae88 tp : ffffffe000e70000 t0 : ffffffff80cb80cf [ 0.402800] t1 : ffffffff80cb80c0 t2 : 0000000000000000 s0 : ffffffe000e7bc80 [ 0.403310] s1 : ffffffe000e7bde8 a0 : 0000000000000053 a1 : ffffffff80c83ff0 [ 0.403805] a2 : 0000000000000010 a3 : 0000000000000000 a4 : 6c7e7a5137233100 [ 0.404298] a5 : 6c7e7a5137233100 a6 : 0000000000000030 a7 : ffffffffffffffff [ 0.404849] s2 : ffffffff80e00000 s3 : 0000000040000000 s4 : 0000000000000000 [ 0.405393] s5 : 0000000000000000 s6 : 0000000000000003 s7 : ffffffe000e7bd48 [ 0.405935] s8 : ffffffff81000000 s9 : ffffffffc0000000 s10: ffffffe000e7bd48 [ 0.406476] s11: 0000000000001000 t3 : 0000000000000072 t4 : ffffffffffffffff [ 0.407016] t5 : 0000000000000002 t6 : ffffffe000e7b978 [ 0.407435] status: 0000000000000120 badaddr: 0000000000000000 cause: 0000000000000003 [ 0.408052] Call Trace: [ 0.408343] [<ffffffff80007c86>] note_page+0x244/0x24a [ 0.408855] [<ffffffff8010c5a6>] ptdump_hole+0x14/0x1e [ 0.409263] [<ffffffff800f65c6>] walk_pgd_range+0x2a0/0x376 [ 0.409690] [<ffffffff800f6828>] walk_page_range_novma+0x4e/0x6e [ 0.410146] [<ffffffff8010c5f8>] ptdump_walk_pgd+0x48/0x78 [ 0.410570] [<ffffffff80007d66>] ptdump_check_wx+0xb4/0xf8 [ 0.410990] [<ffffffff80006738>] mark_rodata_ro+0x26/0x2e [ 0.411407] [<ffffffff8031961e>] kernel_init+0x44/0x108 [ 0.411814] [<ffffffff80002312>] ret_from_exception+0x0/0xc [ 0.412309] ---[ end trace 7ec3459f2547ea83 ]--- [ 0.413141] Checked W+X mappings: failed, 512 W+X pages found Fixes: 2bfc6cd81bd17e43 ("riscv: Move kernel mapping outside of linear mapping") Signed-off-by: Jisheng Zhang <[email protected]> Signed-off-by: Palmer Dabbelt <[email protected]>
2021-06-01Merge branch 'for-linus' of ↵Linus Torvalds28-70/+206
git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid Pull HID fixes from Jiri Kosina: - memory leak fix in usbhid from Anirudh Rayabharam - additions for a few new recognized generic key IDs from Dmitry Torokhov - Asus T101HA and Dell K15A quirks from Hans de Goede - memory leak fix in amd_sfh from Basavaraj Natikar - Win8 compatibility and Stylus fixes in multitouch driver from Ahelenia Ziemiańska - NULL pointer dereference fix in hid-magicmouse from Johan Hovold - assorted other small fixes and device ID additions * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid: (33 commits) HID: asus: Cleanup Asus T101HA keyboard-dock handling HID: magicmouse: fix NULL-deref on disconnect HID: intel-ish-hid: ipc: Add Alder Lake device IDs HID: i2c-hid: fix format string mismatch HID: amd_sfh: Fix memory leak in amd_sfh_work HID: amd_sfh: Use devm_kzalloc() instead of kzalloc() HID: ft260: improve error handling of ft260_hid_feature_report_get() HID: magicmouse: fix crash when disconnecting Magic Trackpad 2 HID: gt683r: add missing MODULE_DEVICE_TABLE HID: pidff: fix error return code in hid_pidff_init() HID: logitech-hidpp: initialize level variable HID: multitouch: Disable event reporting on suspend on the Asus T101HA touchpad HID: core: Remove extraneous empty line before EXPORT_SYMBOL_GPL(hid_check_keys_pressed) HID: hid-sensor-custom: Process failure of sensor_hub_set_feature() HID: i2c-hid: Skip ELAN power-on command after reset HID: usbhid: fix info leak in hid_submit_ctrl HID: Add BUS_VIRTUAL to hid_connect logging HID: multitouch: set Stylus suffix for Stylus-application devices, too HID: multitouch: require Finger field to mark Win8 reports as MT HID: remove the unnecessary redefinition of a macro ...
2021-06-01scsi: scsi_devinfo: Add blacklist entry for HPE OPEN-VEwan D. Milne1-0/+1
Apparently some arrays are now returning "HPE" as the vendor. Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Ewan D. Milne <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2021-06-01Merge tag 'gfs2-v5.13-rc2-fixes2' of ↵Linus Torvalds1-3/+1
git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2 Pull gfs2 fix from Andreas Gruenbacher: "Revert broken commit" * tag 'gfs2-v5.13-rc2-fixes2' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2: Revert "gfs2: Fix mmap locking for write faults"
2021-06-01Bluetooth: Add a new USB ID for RTL8822CELarry Finger1-0/+2
Some models of the RTL8822ce utilize a different USB ID. Add this new one to the Bluetooth driver. Signed-off-by: Larry Finger <[email protected]> Signed-off-by: Linus Torvalds <[email protected]>
2021-06-01scsi: ufs: ufs-mediatek: Fix HCI version in some platformsStanley Chu1-1/+14
Some MediaTek SoC platforms with UFSHCI version below 3.0 have incorrect UFSHCI versions showed in register map. Fix the version by referring to UniPro version which is always correct. Link: https://lore.kernel.org/r/[email protected] Reviewed-by: Alim Akhtar <[email protected]> Signed-off-by: Stanley Chu <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2021-06-01scsi: qedf: Do not put host in qedf_vport_create() unconditionallyDaniel Wagner1-11/+9
Do not drop reference count on vn_port->host in qedf_vport_create() unconditionally. Instead drop the reference count in qedf_vport_destroy(). Link: https://lore.kernel.org/r/[email protected] Reported-by: Javed Hasan <[email protected]> Signed-off-by: Daniel Wagner <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2021-06-01net/mlx5: DR, Create multi-destination flow table with level less than 64Yevgeny Kliteynik2-1/+4
Flow table that contains flow pointing to multiple flow tables or multiple TIRs must have a level lower than 64. In our case it applies to muli- destination flow table. Fix the level of the created table to comply with HW Spec definitions, and still make sure that its level lower than SW-owned tables, so that it would be possible to point from the multi-destination FW table to SW tables. Fixes: 34583beea4b7 ("net/mlx5: DR, Create multi-destination table for SW-steering use") Signed-off-by: Yevgeny Kliteynik <[email protected]> Reviewed-by: Alex Vesker <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>
2021-06-01net/mlx5e: Fix conflict with HW TS and CQE compressionAya Levin1-0/+7
When a driver's profile doesn't support a dedicated PTP-RQ, configuration of CQE compression while HW TS is configured should fail. Fixes: 885b8cfb161e ("net/mlx5e: Update ethtool setting of CQE compression") Signed-off-by: Aya Levin <[email protected]> Reviewed-by: Moshe Shemesh <[email protected]> Reviewed-by: Tariq Toukan <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>
2021-06-01net/mlx5e: Fix HW TS with CQE compression according to profileAya Levin1-15/+52
When the driver's profile doesn't support a dedicated PTP-RQ, the PTP accuracy of HW TS is affected by the CQE compression. In this case, turn off CQE compression. Otherwise, the driver crashes: BUG: kernel NULL pointer dereference, address:0000000000000018 ... ... RIP: 0010:mlx5e_ptp_rx_set_fs+0x25/0x1a0 [mlx5_core] ... ... Call Trace: mlx5e_ptp_activate_channel+0xb2/0xf0 [mlx5_core] mlx5e_activate_priv_channels+0x3b9/0x8c0 [mlx5_core] ? __mutex_unlock_slowpath+0x45/0x2a0 ? mlx5e_refresh_tirs+0x151/0x1e0 [mlx5_core] mlx5e_switch_priv_channels+0x1cd/0x2d0 [mlx5_core] ? mlx5e_xdp_allowed+0x150/0x150 [mlx5_core] mlx5e_safe_switch_params+0x118/0x3c0 [mlx5_core] ? __mutex_lock+0x6e/0x8e0 ? mlx5e_hwstamp_set+0xa9/0x300 [mlx5_core] mlx5e_hwstamp_set+0x194/0x300 [mlx5_core] ? dev_ioctl+0x9b/0x3d0 mlx5i_ioctl+0x37/0x60 [mlx5_core] mlx5i_pkey_ioctl+0x12/0x20 [mlx5_core] dev_ioctl+0xa9/0x3d0 sock_ioctl+0x268/0x420 __x64_sys_ioctl+0x3d8/0x790 ? lockdep_hardirqs_on_prepare+0xe4/0x190 do_syscall_64+0x2d/0x40 entry_SYSCALL_64_after_hwframe+0x44/0xae Fixes: 960fbfe222a4 ("net/mlx5e: Allow coexistence of CQE compression and HW TS PTP") Signed-off-by: Aya Levin <[email protected]> Reviewed-by: Moshe Shemesh <[email protected]> Reviewed-by: Tariq Toukan <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>
2021-06-01net/mlx5e: Fix adding encap rules to slow pathRoi Dayan3-2/+8
On some devices the ignore flow level cap is not supported and we shouldn't use it. Setting the dest ft with mlx5_chains_get_tc_end_ft() already gives the correct end ft if ignore flow level cap is supported or not. Fixes: 39ac237ce009 ("net/mlx5: E-Switch, Refactor chains and priorities") Signed-off-by: Roi Dayan <[email protected]> Reviewed-by: Paul Blakey <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>
2021-06-01net/mlx5e: Check for needed capability for cvlan matchingRoi Dayan1-0/+9
If not supported show an error and return instead of trying to offload to the hardware and fail. Fixes: 699e96ddf47f ("net/mlx5e: Support offloading tc double vlan headers match") Reported-by: Pablo Neira Ayuso <[email protected]> Signed-off-by: Roi Dayan <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>
2021-06-01net/mlx5: Check firmware sync reset requested is set before trying to abort itMoshe Shemesh1-0/+3
In case driver sent NACK to firmware on sync reset request, it will get sync reset abort event while it didn't set sync reset requested mode. Thus, on abort sync reset event handler, driver should check reset requested is set before trying to stop sync reset poll. Fixes: 7dd6df329d4c ("net/mlx5: Handle sync reset abort event") Signed-off-by: Moshe Shemesh <[email protected]> Reviewed-by: Tariq Toukan <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>
2021-06-01net/mlx5e: Disable TLS offload for uplink representorRoi Dayan1-0/+10
TLS offload is not supported in switchdev mode. Fixes: 7a9fb35e8c3a ("net/mlx5e: Do not reload ethernet ports when changing eswitch mode") Signed-off-by: Roi Dayan <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>
2021-06-01net/mlx5e: Fix incompatible castingAya Levin1-2/+3
Device supports setting of a single fec mode at a time, enforce this by bitmap_weight == 1. Input from fec command is in u32, avoid cast to unsigned long and use bitmap_from_arr32 to populate bitmap safely. Fixes: 4bd9d5070b92 ("net/mlx5e: Enforce setting of a single FEC mode") Signed-off-by: Aya Levin <[email protected]> Reviewed-by: Tariq Toukan <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>
2021-06-01MAINTAINERS: nfc mailing lists are subscribers-onlyJoe Perches1-5/+5
It looks as if the MAINTAINERS entries for the nfc mailing list should be updated as I just got a "rejected" bounce from the nfc list. ------- Your message to the Linux-nfc mailing-list was rejected for the following reasons: The message is not from a list member ------- Signed-off-by: Joe Perches <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2021-06-01Merge branch 'ktls-use-after-free'David S. Miller4-12/+66
Maxim Mikityanskiy says: ==================== Fix use-after-free after the TLS device goes down and up This small series fixes a use-after-free bug in the TLS offload code. The first patch is a preparation for the second one, and the second is the fix itself. v2 changes: Remove unneeded EXPORT_SYMBOL_GPL. ==================== Acked-by: Jakub Kicinski <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2021-06-01net/tls: Fix use-after-free after the TLS device goes down and upMaxim Mikityanskiy4-5/+64
When a netdev with active TLS offload goes down, tls_device_down is called to stop the offload and tear down the TLS context. However, the socket stays alive, and it still points to the TLS context, which is now deallocated. If a netdev goes up, while the connection is still active, and the data flow resumes after a number of TCP retransmissions, it will lead to a use-after-free of the TLS context. This commit addresses this bug by keeping the context alive until its normal destruction, and implements the necessary fallbacks, so that the connection can resume in software (non-offloaded) kTLS mode. On the TX side tls_sw_fallback is used to encrypt all packets. The RX side already has all the necessary fallbacks, because receiving non-decrypted packets is supported. The thing needed on the RX side is to block resync requests, which are normally produced after receiving non-decrypted packets. The necessary synchronization is implemented for a graceful teardown: first the fallbacks are deployed, then the driver resources are released (it used to be possible to have a tls_dev_resync after tls_dev_del). A new flag called TLS_RX_DEV_DEGRADED is added to indicate the fallback mode. It's used to skip the RX resync logic completely, as it becomes useless, and some objects may be released (for example, resync_async, which is allocated and freed by the driver). Fixes: e8f69799810c ("net/tls: Add generic NIC offload infrastructure") Signed-off-by: Maxim Mikityanskiy <[email protected]> Reviewed-by: Tariq Toukan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2021-06-01net/tls: Replace TLS_RX_SYNC_RUNNING with RCUMaxim Mikityanskiy2-8/+3
RCU synchronization is guaranteed to finish in finite time, unlike a busy loop that polls a flag. This patch is a preparation for the bugfix in the next patch, where the same synchronize_net() call will also be used to sync with the TX datapath. Signed-off-by: Maxim Mikityanskiy <[email protected]> Reviewed-by: Tariq Toukan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2021-06-01ethernet: myri10ge: Fix missing error code in myri10ge_probe()Jiapeng Chong1-0/+1
The error code is missing in this code scenario, add the error code '-EINVAL' to the return value 'status'. Eliminate the follow smatch warning: drivers/net/ethernet/myricom/myri10ge/myri10ge.c:3818 myri10ge_probe() warn: missing error code 'status'. Reported-by: Abaci Robot <[email protected]> Signed-off-by: Jiapeng Chong <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2021-06-01Merge branch 'virtio_net-build_skb-fixes'David S. Miller1-12/+8
Xuan Zhuo says: ==================== virtio-net: fix for build_skb() The logic of this piece is really messy. Fortunately, my refactored patch can be completed with a small amount of testing. ==================== Acked-by: Michael S. Tsirkin <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2021-06-01virtio_net: get build_skb() buf by data ptrXuan Zhuo1-11/+6
In the case of merge, the page passed into page_to_skb() may be a head page, not the page where the current data is located. So when trying to get the buf where the data is located, we should get buf based on headroom instead of offset. This patch solves this problem. But if you don't use this patch, the original code can also run, because if the page is not the page of the current data, the calculated tailroom will be less than 0, and will not enter the logic of build_skb() . The significance of this patch is to modify this logical problem, allowing more situations to use build_skb(). Signed-off-by: Xuan Zhuo <[email protected]> Acked-by: Jason Wang <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2021-06-01virtio-net: fix for unable to handle page fault for addressXuan Zhuo1-1/+2
In merge mode, when xdp is enabled, if the headroom of buf is smaller than virtnet_get_headroom(), xdp_linearize_page() will be called but the variable of "headroom" is still 0, which leads to wrong logic after entering page_to_skb(). [ 16.600944] BUG: unable to handle page fault for address: ffffecbfff7b43c8[ 16.602175] #PF: supervisor read access in kernel mode [ 16.603350] #PF: error_code(0x0000) - not-present page [ 16.604200] PGD 0 P4D 0 [ 16.604686] Oops: 0000 [#1] SMP PTI [ 16.605306] CPU: 4 PID: 715 Comm: sh Tainted: G B 5.12.0+ #312 [ 16.606429] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/04 [ 16.608217] RIP: 0010:unmap_page_range+0x947/0xde0 [ 16.609014] Code: 00 00 08 00 48 83 f8 01 45 19 e4 41 f7 d4 41 83 e4 03 e9 a4 fd ff ff e8 b7 63 ed ff 4c 89 e0 48 c1 e0 065 [ 16.611863] RSP: 0018:ffffc90002503c58 EFLAGS: 00010286 [ 16.612720] RAX: ffffecbfff7b43c0 RBX: 00007f19f7203000 RCX: ffffffff812ff359 [ 16.613853] RDX: ffff888107778000 RSI: 0000000000000000 RDI: 0000000000000005 [ 16.614976] RBP: ffffea000425e000 R08: 0000000000000000 R09: 3030303030303030 [ 16.616124] R10: ffffffff82ed7d94 R11: 6637303030302052 R12: 7c00000afffded0f [ 16.617276] R13: 0000000000000001 R14: ffff888119ee7010 R15: 00007f19f7202000 [ 16.618423] FS: 0000000000000000(0000) GS:ffff88842fd00000(0000) knlGS:0000000000000000 [ 16.619738] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 16.620670] CR2: ffffecbfff7b43c8 CR3: 0000000103220005 CR4: 0000000000370ee0 [ 16.621792] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 16.622920] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 16.624047] Call Trace: [ 16.624525] ? release_pages+0x24d/0x730 [ 16.625209] unmap_single_vma+0xa9/0x130 [ 16.625885] unmap_vmas+0x76/0xf0 [ 16.626480] exit_mmap+0xa0/0x210 [ 16.627129] mmput+0x67/0x180 [ 16.627673] do_exit+0x3d1/0xf10 [ 16.628259] ? do_user_addr_fault+0x231/0x840 [ 16.629000] do_group_exit+0x53/0xd0 [ 16.629631] __x64_sys_exit_group+0x1d/0x20 [ 16.630354] do_syscall_64+0x3c/0x80 [ 16.630988] entry_SYSCALL_64_after_hwframe+0x44/0xae [ 16.631828] RIP: 0033:0x7f1a043d0191 [ 16.632464] Code: Unable to access opcode bytes at RIP 0x7f1a043d0167. [ 16.633502] RSP: 002b:00007ffe3d993308 EFLAGS: 00000246 ORIG_RAX: 00000000000000e7 [ 16.634737] RAX: ffffffffffffffda RBX: 00007f1a044c9490 RCX: 00007f1a043d0191 [ 16.635857] RDX: 000000000000003c RSI: 00000000000000e7 RDI: 0000000000000000 [ 16.636986] RBP: 0000000000000000 R08: ffffffffffffff88 R09: 0000000000000001 [ 16.638120] R10: 0000000000000008 R11: 0000000000000246 R12: 00007f1a044c9490 [ 16.639245] R13: 0000000000000001 R14: 00007f1a044c9968 R15: 0000000000000000 [ 16.640408] Modules linked in: [ 16.640958] CR2: ffffecbfff7b43c8 [ 16.641557] ---[ end trace bc4891c6ce46354c ]--- [ 16.642335] RIP: 0010:unmap_page_range+0x947/0xde0 [ 16.643135] Code: 00 00 08 00 48 83 f8 01 45 19 e4 41 f7 d4 41 83 e4 03 e9 a4 fd ff ff e8 b7 63 ed ff 4c 89 e0 48 c1 e0 065 [ 16.645983] RSP: 0018:ffffc90002503c58 EFLAGS: 00010286 [ 16.646845] RAX: ffffecbfff7b43c0 RBX: 00007f19f7203000 RCX: ffffffff812ff359 [ 16.647970] RDX: ffff888107778000 RSI: 0000000000000000 RDI: 0000000000000005 [ 16.649091] RBP: ffffea000425e000 R08: 0000000000000000 R09: 3030303030303030 [ 16.650250] R10: ffffffff82ed7d94 R11: 6637303030302052 R12: 7c00000afffded0f [ 16.651394] R13: 0000000000000001 R14: ffff888119ee7010 R15: 00007f19f7202000 [ 16.652529] FS: 0000000000000000(0000) GS:ffff88842fd00000(0000) knlGS:0000000000000000 [ 16.653887] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 16.654841] CR2: ffffecbfff7b43c8 CR3: 0000000103220005 CR4: 0000000000370ee0 [ 16.655992] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 16.657150] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 16.658290] Kernel panic - not syncing: Fatal exception [ 16.659613] Kernel Offset: disabled [ 16.660234] ---[ end Kernel panic - not syncing: Fatal exception ]--- Fixes: fb32856b16ad ("virtio-net: page_to_skb() use build_skb when there's sufficient tailroom") Signed-off-by: Xuan Zhuo <[email protected]> Acked-by: Jason Wang <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2021-06-01net: sock: fix in-kernel mark settingAlexander Aring1-4/+12
This patch fixes the in-kernel mark setting by doing an additional sk_dst_reset() which was introduced by commit 50254256f382 ("sock: Reset dst when changing sk_mark via setsockopt"). The code is now shared to avoid any further suprises when changing the socket mark value. Fixes: 84d1c617402e ("net: sock: add sock_set_mark") Reported-by: Marcelo Ricardo Leitner <[email protected]> Signed-off-by: Alexander Aring <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2021-06-01net: dsa: tag_8021q: fix the VLAN IDs used for encoding sub-VLANsVladimir Oltean1-1/+1
When using sub-VLANs in the range of 1-7, the resulting value from: rx_vid = dsa_8021q_rx_vid_subvlan(ds, port, subvlan); is wrong according to the description from tag_8021q.c: | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | +-----------+-----+-----------------+-----------+-----------------------+ | DIR | SVL | SWITCH_ID | SUBVLAN | PORT | +-----------+-----+-----------------+-----------+-----------------------+ For example, when ds->index == 0, port == 3 and subvlan == 1, dsa_8021q_rx_vid_subvlan() returns 1027, same as it returns for subvlan == 0, but it should have returned 1043. This is because the low portion of the subvlan bits are not masked properly when writing into the 12-bit VLAN value. They are masked into bits 4:3, but they should be masked into bits 5:4. Fixes: 3eaae1d05f2b ("net: dsa: tag_8021q: support up to 8 VLANs per port using sub-VLANs") Signed-off-by: Vladimir Oltean <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2021-06-01Revert "gfs2: Fix mmap locking for write faults"Andreas Gruenbacher1-3/+1
This reverts commit b7f55d928e75557295c1ac280c291b738905b6fb. As explained by Linus in [*], write faults on a mmap region are reads from a filesysten point of view, so taking the inode glock exclusively on write faults is incorrect. Instead, when a page is marked writable, the .page_mkwrite vm operation will be called, which is where the exclusive lock taking needs to happen. I got this wrong because of a broken test case that made me believe .page_mkwrite isn't getting called when it actually is. [*] https://lore.kernel.org/lkml/CAHk-=wj8EWr_D65i4oRSj2FTbrc6RdNydNNCGxeabRnwtoU=3Q@mail.gmail.com/ Signed-off-by: Andreas Gruenbacher <[email protected]>
2021-06-01Revert "fb_defio: Remove custom address_space_operations"Matthew Wilcox3-0/+42
Commit ccf953d8f3d6 makes framebuffers which use deferred I/O stop displaying updates after the first one. This is because the pages handled by fb_defio no longer have a page_mapping(). That prevents page_mkclean() from marking the PTEs as clean, and so writes are only noticed the first time. Reported-by: Andy Shevchenko <[email protected]> Signed-off-by: Matthew Wilcox (Oracle) <[email protected]> Signed-off-by: Daniel Vetter <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
2021-06-01perf test: Test 17 fails with make LIBPFM4=1 on s390 z/VMThomas Richter1-1/+1
This test case fails on s390 virtual machine z/VM which has no PMU support when the perf tool is built with LIBPFM4=1. Using make LIBPFM4=1 builds the perf tool with support for libpfm event notation. The command line flag --pfm-events is valid: # ./perf record --pfm-events cycles -- true [ perf record: Woken up 1 times to write data ] [ perf record: Captured and wrote 0.001 MB perf.data (2 samples) ] # However the command 'perf test -Fv 17' fails on s390 z/VM virtual machine with LIBPFM4=1: # perf test -Fv 17 17: Setup struct perf_event_attr : --- start --- ..... running './tests/attr/test-record-group2' unsupp './tests/attr/test-record-group2' running './tests/attr/test-record-pfm-period' expected exclude_hv=0, got 1 FAILED './tests/attr/test-record-pfm-period' - match failure ---- end ---- Setup struct perf_event_attr: FAILED! When --pfm-event system is not supported, the test returns unsupported and continues. Here is an example using a virtual machine on x86 and Fedora 34: [root@f33 perf]# perf test -Fv 17 17: Setup struct perf_event_attr : --- start --- ..... running './tests/attr/test-record-group2' unsupp './tests/attr/test-record-group2' running './tests/attr/test-record-pfm-period' unsupp './tests/attr/test-record-pfm-period' .... The issue is file ./tests/attr/test-record-pfm-period which requires perf event attribute member exclude_hv to be zero. This is not the case on s390 where the value of exclude_hv is one when executing on a z/VM virtual machine without PMU hardware support. Fix this by allowing value exlucde_hv to be zero or one. Output before: # /usr/bin/python ./tests/attr.py -d ./tests/attr/ -t \ test-record-pfm-period -p ./perf -vvv 2>&1| fgrep match matching [event:base-record] match: [event:base-record] matches [] FAILED './tests/attr//test-record-pfm-period' - match failure # Output after: # /usr/bin/python ./tests/attr.py -d ./tests/attr/ -t \ test-record-pfm-period -p ./perf -vvv 2>&1| fgrep match matching [event:base-record] match: [event:base-record] matches ['event-1-0-6', 'event-1-0-5'] matched Background: Using libpfm library ends up in this function call sequence pfm_get_perf_event_encoding() +-- pfm_get_os_event_encoding() +-- pfmlib_perf_event_encode() is called when no hardware specific PMU unit can be detected as in the s390 z/VM virtual machine case. This uses the "perf_events generic PMU" data structure which sets exclude_hv to 1 per default. Using this PMU that test case always fails. That is the reason why exclude_hv attribute setting varies. Version 2: As suggested by Ian Rogers make perf_event_attribute member exclude_hv more robust and accept value 0 or 1 to handle more test cases which might fail on s390 virtual machine z/VM. Suggested-by: Ian Rogers <[email protected]> Signed-off-by: Thomas Richter <[email protected]> Reviewed-by: Ian Rogers <[email protected]> Cc: Heiko Carstens <[email protected]> Cc: Ian Rogers <[email protected]> Cc: Sumanth Korikkar <[email protected]> Cc: Sven Schnelle <[email protected]> Cc: Vasily Gorbik <[email protected]> Link: http://lore.kernel.org/lkml/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
2021-06-01perf stat: Fix error return code in bperf__load()Yu Kuai1-2/+4
Fix to return a negative error code from the error handling case instead of 0, as done elsewhere in this function. Committer notes: Added the missing {} for the now multiline 'if' block, fixing this error: CC /tmp/build/perf/util/bpf_counter.o util/bpf_counter.c: In function ‘bperf__load’: util/bpf_counter.c:523:9: error: this ‘if’ clause does not guard... [-Werror=misleading-indentation] 523 | if (evsel->bperf_leader_link_fd < 0 && | ^~ util/bpf_counter.c:526:17: note: ...this statement, but the latter is misleadingly indented as if it were guarded by the ‘if’ 526 | goto out; | ^~~~ cc1: all warnings being treated as errors Fixes: 7fac83aaf2eecc9e ("perf stat: Introduce 'bperf' to share hardware PMCs with BPF") Reported-by: Hulk Robot <[email protected]> Signed-off-by: Yu Kuai <[email protected]> Cc: Alexei Starovoitov <[email protected]> Cc: Andrii Nakryiko <[email protected]> Cc: Daniel Borkmann <[email protected]> Cc: Peter Zijlstra <[email protected]> Cc: Song Liu <[email protected]> Cc: Yu Kuai <[email protected]> Cc: Zhang Yi <[email protected]> Link: http://lore.kernel.org/lkml/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
2021-06-01perf record: Move probing cgroup sampling supportNamhyung Kim3-0/+17
I found that checking cgroup sampling support using the missing features doesn't work on old kernels. Because it added both attr.cgroup bit and PERF_SAMPLE_CGROUP bit, it needs to check whichever comes first (usually the actual event, not dummy). But it only checks the attr.cgroup bit which is set only in the dummy event so cannot detect failtures due the sample bits. Also we don't ignore the missing feature and retry, it'd be better checking it with the API probing logic. Committer notes: Extracted the minimal part to check using the new cgroup API probe routine, the part that removes the cgroup member can be left for further discussion. Signed-off-by: Namhyung Kim <[email protected]> Cc: Alexander Shishkin <[email protected]> Cc: Andi Kleen <[email protected]> Cc: Ian Rogers <[email protected]> Cc: Jiri Olsa <[email protected]> Cc: Mark Rutland <[email protected]> Cc: Peter Zijlstra <[email protected]> Link: http://lore.kernel.org/lkml/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
2021-06-01perf probe: Fix NULL pointer dereference in convert_variable_location()Li Huafei2-2/+9
If we just check whether the variable can be converted, 'tvar' should be a null pointer. However, the null pointer check is missing in the 'Constant value' execution path. The following cases can trigger this problem: $ cat test.c #include <stdio.h> void main(void) { int a; const int b = 1; asm volatile("mov %1, %0" : "=r"(a): "i"(b)); printf("a: %d\n", a); } $ gcc test.c -o test -O -g $ sudo ./perf probe -x ./test -L "main" <main@/home/lhf/test.c:0> 0 void main(void) { 2 int a; const int b = 1; asm volatile("mov %1, %0" : "=r"(a): "i"(b)); 6 printf("a: %d\n", a); } $ sudo ./perf probe -x ./test -V "main:6" Segmentation fault The check on 'tvar' is added. If 'tavr' is a null pointer, we return 0 to indicate that the variable can be converted. Now, we can successfully show the variables that can be accessed. $ sudo ./perf probe -x ./test -V "main:6" Available variables at main:6 @<main+13> char* __fmt int a int b However, the variable 'b' cannot be tracked. $ sudo ./perf probe -x ./test -D "main:6 b" Failed to find the location of the 'b' variable at this address. Perhaps it has been optimized out. Use -V with the --range option to show 'b' location range. Error: Failed to add events. This is because __die_find_variable_cb() did not successfully match variable 'b', which has the DW_AT_const_value attribute instead of DW_AT_location. We added support for DW_AT_const_value in __die_find_variable_cb(). With this modification, we can successfully track the variable 'b'. $ sudo ./perf probe -x ./test -D "main:6 b" p:probe_test/main_L6 /home/lhf/test:0x1156 b=\1:s32 Fixes: 66f69b219716 ("perf probe: Support DW_AT_const_value constant value") Signed-off-by: Li Huafei <[email protected]> Tested-by: Arnaldo Carvalho de Melo <[email protected]> Cc: Alexander Shishkin <[email protected]> Cc: Frank Ch. Eigler <[email protected]> Cc: Jianlin Lv <[email protected]> Cc: Jiri Olsa <[email protected]> Cc: Mark Rutland <[email protected]> Cc: Masami Hiramatsu <[email protected]> Cc: Namhyung Kim <[email protected]> Cc: Peter Zijlstra <[email protected]> Cc: Srikar Dronamraju <[email protected]> Cc: Yang Jihong <[email protected]> Cc: Zhang Jinhao <[email protected]> http://lore.kernel.org/lkml/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
2021-06-01perf tools: Copy uapi/asm/perf_regs.h from the kernel for MIPSTiezhu Yang3-1/+41
To allow the build to complete on older systems, where those files are either not uptodate, lacking some recent additions or not present at all. And check if the copy drifts from the kernel. This commit is similar with commit 12f020338a2c ("tools: Copy uapi/asm/perf_regs.h from the kernel") With this commit, we can avoid the following build error in any case: tools/perf/arch/mips/include/perf_regs.h:7:10: fatal error: asm/perf_regs.h: No such file or directory #include <asm/perf_regs.h> ^~~~~~~~~~~~~~~~~ compilation terminated. Signed-off-by: Tiezhu Yang <[email protected]> Cc: Alexander Shishkin <[email protected]> Cc: Jiri Olsa <[email protected]> Cc: Mark Rutland <[email protected]> Cc: Namhyung Kim <[email protected]> Cc: Peter Zijlstra <[email protected]> Cc: Xuefeng Li <[email protected]> Link: http://lore.kernel.org/lkml/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
2021-06-01ALSA: hda: Fix for mute key LED for HP Pavilion 15-CK0xxCarlos M1-0/+1
For the HP Pavilion 15-CK0xx, with audio subsystem ID 0x103c:0x841c, adding a line in patch_realtek.c to apply the ALC269_FIXUP_HP_MUTE_LED_MIC3 fix activates the mute key LED. Signed-off-by: Carlos M <[email protected]> Cc: <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Takashi Iwai <[email protected]>
2021-06-01ALSA: hda/cirrus: Set Initial DMIC volume to -26 dBStefan Binding1-4/+3
Previously this fix was applied only to Bullseye variant laptops, and should be applied to Cyborg and Warlock variants. Fixes: 45b14fe200ba ("ALSA: hda/cirrus: Use CS8409 filter to fix abnormal sounds on Bullseye") Signed-off-by: Stefan Binding <[email protected]> Signed-off-by: Vitaly Rodionov <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Takashi Iwai <[email protected]>
2021-05-31nfc: fix NULL ptr dereference in llcp_sock_getname() after failed connectKrzysztof Kozlowski1-0/+2
It's possible to trigger NULL pointer dereference by local unprivileged user, when calling getsockname() after failed bind() (e.g. the bind fails because LLCP_SAP_MAX used as SAP): BUG: kernel NULL pointer dereference, address: 0000000000000000 CPU: 1 PID: 426 Comm: llcp_sock_getna Not tainted 5.13.0-rc2-next-20210521+ #9 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-1 04/01/2014 Call Trace: llcp_sock_getname+0xb1/0xe0 __sys_getpeername+0x95/0xc0 ? lockdep_hardirqs_on_prepare+0xd5/0x180 ? syscall_enter_from_user_mode+0x1c/0x40 __x64_sys_getpeername+0x11/0x20 do_syscall_64+0x36/0x70 entry_SYSCALL_64_after_hwframe+0x44/0xae This can be reproduced with Syzkaller C repro (bind followed by getpeername): https://syzkaller.appspot.com/x/repro.c?x=14def446e00000 Cc: <[email protected]> Fixes: d646960f7986 ("NFC: Initial LLCP support") Reported-by: [email protected] Reported-by: butt3rflyh4ck <[email protected]> Signed-off-by: Krzysztof Kozlowski <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2021-05-31scsi: lpfc: Fix failure to transmit ABTS on FC linkJames Smart1-3/+1
The abort_cmd_ia flag in an abort wqe describes whether an ABTS basic link service should be transmitted on the FC link or not. Code added in lpfc_sli4_issue_abort_iotag() set the abort_cmd_ia flag incorrectly, surpressing ABTS transmission. A previous LPFC change to build an abort wqe inverted prior logic that determined whether an ABTS was to be issued on the FC link. Revert this logic to its proper state. Link: https://lore.kernel.org/r/[email protected] Fixes: db7531d2b377 ("scsi: lpfc: Convert abort handling to SLI-3 and SLI-4 handlers") Cc: <[email protected]> # v5.11+ Signed-off-by: James Smart <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2021-05-31scsi: target: core: Fix warning on realtime kernelsMaurizio Lombardi1-3/+1
On realtime kernels, spin_lock_irq*(spinlock_t) do not disable the interrupts, a call to irqs_disabled() will return false thus firing a warning in __transport_wait_for_tasks(). Remove the warning and also replace assert_spin_locked() with lockdep_assert_held() Link: https://lore.kernel.org/r/[email protected] Reviewed-by: Bart Van Assche <[email protected]> Signed-off-by: Maurizio Lombardi <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2021-06-01Revert "powerpc/kernel/iommu: Align size for IOMMU_PAGE_SIZE() to save TCEs"Frederic Barrat1-6/+5
This reverts commit 3c0468d4451eb6b4f6604370639f163f9637a479. That commit was breaking alignment guarantees for the DMA address when allocating coherent mappings, as described in Documentation/core-api/dma-api-howto.rst It was also noticed by Mellanox' driver: [ 1515.763621] mlx5_core c002:01:00.0: mlx5_frag_buf_alloc_node:146:(pid 13402): unexpected map alignment: 0x0800000000c61000, page_shift=16 [ 1515.763635] mlx5_core c002:01:00.0: mlx5_cqwq_create:181:(pid 13402): mlx5_frag_buf_alloc_node() failed, -12 Fixes: 3c0468d4451e ("powerpc/kernel/iommu: Align size for IOMMU_PAGE_SIZE() to save TCEs") Signed-off-by: Frederic Barrat <[email protected]> Reviewed-by: Alexey Kardashevskiy <[email protected]> Signed-off-by: Michael Ellerman <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2021-05-31x86/thermal: Fix LVT thermal setup for SMI delivery modeBorislav Petkov3-5/+23
There are machines out there with added value crap^WBIOS which provide an SMI handler for the local APIC thermal sensor interrupt. Out of reset, the BSP on those machines has something like 0x200 in that APIC register (timestamps left in because this whole issue is timing sensitive): [ 0.033858] read lvtthmr: 0x330, val: 0x200 which means: - bit 16 - the interrupt mask bit is clear and thus that interrupt is enabled - bits [10:8] have 010b which means SMI delivery mode. Now, later during boot, when the kernel programs the local APIC, it soft-disables it temporarily through the spurious vector register: setup_local_APIC: ... /* * If this comes from kexec/kcrash the APIC might be enabled in * SPIV. Soft disable it before doing further initialization. */ value = apic_read(APIC_SPIV); value &= ~APIC_SPIV_APIC_ENABLED; apic_write(APIC_SPIV, value); which means (from the SDM): "10.4.7.2 Local APIC State After It Has Been Software Disabled ... * The mask bits for all the LVT entries are set. Attempts to reset these bits will be ignored." And this happens too: [ 0.124111] APIC: Switch to symmetric I/O mode setup [ 0.124117] lvtthmr 0x200 before write 0xf to APIC 0xf0 [ 0.124118] lvtthmr 0x10200 after write 0xf to APIC 0xf0 This results in CPU 0 soft lockups depending on the placement in time when the APIC soft-disable happens. Those soft lockups are not 100% reproducible and the reason for that can only be speculated as no one tells you what SMM does. Likely, it confuses the SMM code that the APIC is disabled and the thermal interrupt doesn't doesn't fire at all, leading to CPU 0 stuck in SMM forever... Now, before 4f432e8bb15b ("x86/mce: Get rid of mcheck_intel_therm_init()") due to how the APIC_LVTTHMR was read before APIC initialization in mcheck_intel_therm_init(), it would read the value with the mask bit 16 clear and then intel_init_thermal() would replicate it onto the APs and all would be peachy - the thermal interrupt would remain enabled. But that commit moved that reading to a later moment in intel_init_thermal(), resulting in reading APIC_LVTTHMR on the BSP too late and with its interrupt mask bit set. Thus, revert back to the old behavior of reading the thermal LVT register before the APIC gets initialized. Fixes: 4f432e8bb15b ("x86/mce: Get rid of mcheck_intel_therm_init()") Reported-by: James Feeney <[email protected]> Signed-off-by: Borislav Petkov <[email protected]> Cc: <[email protected]> Cc: Zhang Rui <[email protected]> Cc: Srinivas Pandruvada <[email protected]> Link: https://lkml.kernel.org/r/[email protected]
2021-05-31ALSA: hda: Fix a regression in Capture Switch mixer readTakashi Iwai1-0/+1
The recent commit to drop the HDA-specific mute-LED control, e65bf99718b5 ("ALSA: HDA - remove the custom implementation for the audio LED trigger"), caused a regression on the mixer element read for "Capture Switch" when it's built from bind controls. The function create_bind_cap_vol_ctl() creates the snd_kcontrol_new object directly via snd_hda_gen_add_kctl() instead of add_control(). Although the commit above added a workaround for the SNDRV_CTL_ACCESS_READWRITE in add_control() as default, this code path fell out from the radar. As a result, now the driver gives -EPERM error because of the lack of the proper access bit at reading "Capture Switch" element value. Fix the regression by setting the access bit properly. Fixes: e65bf99718b5 ("ALSA: HDA - remove the custom implementation for the audio LED trigger") BugLink: https://bugzilla.opensuse.org/show_bug.cgi?id=1186634 Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Takashi Iwai <[email protected]>
2021-05-31Merge tag 'gfs2-v5.13-rc2-fixes' of ↵Linus Torvalds8-11/+44
git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2 Pull gfs2 fixes from Andreas Gruenbacher: "Various gfs2 fixes" * tag 'gfs2-v5.13-rc2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2: gfs2: Fix use-after-free in gfs2_glock_shrink_scan gfs2: Fix mmap locking for write faults gfs2: Clean up revokes on normal withdraws gfs2: fix a deadlock on withdraw-during-mount gfs2: fix scheduling while atomic bug in glocks gfs2: Fix I_NEW check in gfs2_dinode_in gfs2: Prevent direct-I/O write fallback errors from getting lost
2021-05-31Merge tag 'fsnotify_for_v5.13-rc5' of ↵Linus Torvalds4-7/+30
git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs Pull fsnotify fixes from Jan Kara: "A fix for permission checking with fanotify unpriviledged groups. Also there's a small update in MAINTAINERS file for fanotify" * tag 'fsnotify_for_v5.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs: fanotify: fix permission model of unprivileged group MAINTAINERS: Add Matthew Bobrowski as a reviewer
2021-05-31Bluetooth: use correct lock to prevent UAF of hdev objectLin Ma1-2/+2
The hci_sock_dev_event() function will cleanup the hdev object for sockets even if this object may still be in used within the hci_sock_bound_ioctl() function, result in UAF vulnerability. This patch replace the BH context lock to serialize these affairs and prevent the race condition. Signed-off-by: Lin Ma <[email protected]> Signed-off-by: Marcel Holtmann <[email protected]>
2021-05-31drm/tegra: Correct DRM_FORMAT_MOD_NVIDIA_SECTOR_LAYOUTDmitry Osipenko1-1/+1
The format modifier is 64bit, while DRM_FORMAT_MOD_NVIDIA_SECTOR_LAYOUT uses BIT() macro that is 32bit on ARM32. The (modifier &= ~DRM_FORMAT_MOD_NVIDIA_SECTOR_LAYOUT) doesn't work as expected on ARM32 and tegra_fb_get_tiling() fails for the tiled formats on 32bit Tegra because modifier mask isn't applied properly. Use the BIT_ULL() macro to fix this trouble. Fixes: 7b6f846785f4 ("drm/tegra: Support sector layout on Tegra194") Signed-off-by: Dmitry Osipenko <[email protected]> Signed-off-by: Thierry Reding <[email protected]>
2021-05-31ACPICA: Clean up context mutex during object deletionErik Kaneda1-0/+8
ACPICA commit bc43c878fd4ff27ba75b1d111b97ee90d4a82707 Fixes: c27f3d011b08 ("Fix race in GenericSerialBus (I2C) and GPIO OpRegion parameter handling") Link: https://github.com/acpica/acpica/commit/bc43c878 Reported-by: John Garry <[email protected]> Reported-by: Xiang Chen <[email protected]> Tested-by: Xiang Chen <[email protected]> Signed-off-by: Erik Kaneda <[email protected]> Signed-off-by: Bob Moore <[email protected]> Signed-off-by: Rafael J. Wysocki <[email protected]>
2021-05-31gfs2: Fix use-after-free in gfs2_glock_shrink_scanHillf Danton1-1/+1
The GLF_LRU flag is checked under lru_lock in gfs2_glock_remove_from_lru() to remove the glock from the lru list in __gfs2_glock_put(). On the shrink scan path, the same flag is cleared under lru_lock but because of cond_resched_lock(&lru_lock) in gfs2_dispose_glock_lru(), progress on the put side can be made without deleting the glock from the lru list. Keep GLF_LRU across the race window opened by cond_resched_lock(&lru_lock) to ensure correct behavior on both sides - clear GLF_LRU after list_del under lru_lock. Reported-by: syzbot <[email protected]> Signed-off-by: Hillf Danton <[email protected]> Signed-off-by: Andreas Gruenbacher <[email protected]>