| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Add support for jump labels based on the ARM64 version.
Acked-by: Peter Zijlstra (Intel) <[email protected]>
Signed-off-by: Youling Tang <[email protected]>
Signed-off-by: Huacai Chen <[email protected]>
|
|
We can see that DEBUG_KMEMLEAK depends on HAVE_DEBUG_KMEMLEAK after
commit b69ec42b1b19 ("Kconfig: clean up the long arch list for the
DEBUG_KMEMLEAK config option"), just select HAVE_DEBUG_KMEMLEAK to
support kmemleak on LoongArch.
Signed-off-by: Tiezhu Yang <[email protected]>
Signed-off-by: Huacai Chen <[email protected]>
|
|
Some PMC (Power Management Controllers) need to support DTS and will use
the suspend interfaces thus this patch was to export such interfaces for
their use.
Signed-off-by: Yinbo Zhu <[email protected]>
Signed-off-by: Huacai Chen <[email protected]>
|
|
Loongson-3A6000 and newer processors have hardware page table walker
(PTW) support. PTW can handle all fastpaths of TLBI/TLBL/TLBS/TLBM
exceptions by hardware, software only need to handle slowpaths (page
faults).
BTW, PTW doesn't append _PAGE_MODIFIED for page table entries, so we
change pmd_dirty() and pte_dirty() to also check _PAGE_DIRTY for the
"dirty" attribute.
Signed-off-by: Liang Gao <[email protected]>
Signed-off-by: Jun Yi <[email protected]>
Signed-off-by: Huacai Chen <[email protected]>
|
|
Traditionally, LoongArch uses "dbar 0" (full completion barrier) for
everything. But the full completion barrier is a performance killer, so
Loongson-3A6000 and newer processors have made finer granularity hints
available:
Bit4: ordering or completion (0: completion, 1: ordering)
Bit3: barrier for previous read (0: true, 1: false)
Bit2: barrier for previous write (0: true, 1: false)
Bit1: barrier for succeeding read (0: true, 1: false)
Bit0: barrier for succeeding write (0: true, 1: false)
Hint 0x700: barrier for "read after read" from the same address, which
is needed by LL-SC loops on old models (dbar 0x700 behaves the same as
nop if such reordering is disabled on new models).
This patch makes use of the various new hints for different kinds of
memory barriers. It brings performance improvements on Loongson-3A6000
series, while not affecting the existing models because all variants are
treated as 'dbar 0' there.
Why override queued_spin_unlock()?
After commit 01e3b958efe85a26d9b ("drivers: Remove explicit invocations
of mmiowb()") we need a completion barrier in queued_spin_unlock(), but
the generic implementation use smp_store_release() which only provide an
ordering barrier.
Signed-off-by: Jun Yi <[email protected]>
Signed-off-by: Huacai Chen <[email protected]>
|
|
Loongson-3A6000 has SMT (Simultaneous Multi-Threading) support, each
physical core has two logical cores (threads). This patch add SMT probe
and scheduler support via ACPI PPTT.
If SCHED_SMT enabled, Loongson-3A6000 is treated as 4 cores, 8 threads;
If SCHED_SMT disabled, Loongson-3A6000 is treated as 8 cores, 8 threads.
Remove smp_num_siblings to support HMP (Heterogeneous Multi-Processing).
Signed-off-by: Liupu Wang <[email protected]>
Signed-off-by: Huacai Chen <[email protected]>
|
|
Add LoongArch's vector extensions support, which including 128bit LSX
(i.e., Loongson SIMD eXtension) and 256bit LASX (i.e., Loongson Advanced
SIMD eXtension).
Linux kernel doesn't use vector itself, it only handle exceptions and
context save/restore. So it only needs a subset of these instructions:
* Vector load/store: vld vst vldx vstx xvld xvst xvldx xvstx
* 8bit-elements move: vpickve2gr.b xvpickve2gr.b vinsgr2vr.b xvinsgr2vr.b
* 16bit-elements move: vpickve2gr.h xvpickve2gr.h vinsgr2vr.h xvinsgr2vr.h
* 32bit-elements move: vpickve2gr.w xvpickve2gr.w vinsgr2vr.w xvinsgr2vr.w
* 64bit-elements move: vpickve2gr.d xvpickve2gr.d vinsgr2vr.d xvinsgr2vr.d
* Elements permute: vpermi.w vpermi.d xvpermi.w xvpermi.d xvpermi.q
Introduce AS_HAS_LSX_EXTENSION and AS_HAS_LASX_EXTENSION to avoid non-
vector toolchains complains unsupported instructions.
Signed-off-by: Huacai Chen <[email protected]>
|
|
We can see that "Time namespaces are not supported" on LoongArch:
(1) clone3 test
# cd tools/testing/selftests/clone3 && make && ./clone3
...
# Time namespaces are not supported
ok 18 # SKIP Skipping clone3() with CLONE_NEWTIME
# Totals: pass:17 fail:0 xfail:0 xpass:0 skip:1 error:0
(2) timens test
# cd tools/testing/selftests/timens && make && ./timens
...
1..0 # SKIP Time namespaces are not supported
On LoongArch the current kernel does not support CONFIG_TIME_NS which
depends on GENERIC_VDSO_TIME_NS, select GENERIC_VDSO_TIME_NS to enable
CONFIG_TIME_NS to build kernel/time/namespace.c.
Additionally, it needs to define some arch-dependent functions for the
timens, such as __arch_get_timens_vdso_data(), arch_get_vdso_data() and
vdso_join_timens().
At the same time, modify the layout of vvar to use one page size for
generic vdso data, expand another page size for timens vdso data and
assign LOONGARCH_VDSO_DATA_SIZE (maybe exceeds a page size if expand in
the future) for loongarch vdso data, at last add the callback function
vvar_fault() and modify stack_top().
With this patch under CONFIG_TIME_NS:
(1) clone3 test
# cd tools/testing/selftests/clone3 && make && ./clone3
...
ok 18 [739] Result (0) matches expectation (0)
# Totals: pass:18 fail:0 xfail:0 xpass:0 skip:0 error:0
(2) timens test
# cd tools/testing/selftests/timens && make && ./timens
...
# Totals: pass:10 fail:0 xfail:0 xpass:0 skip:0 error:0
Signed-off-by: Tiezhu Yang <[email protected]>
Signed-off-by: Huacai Chen <[email protected]>
|
|
The LoongArch kernel is 64-bit and built with the soft-float ABI,
hence the loongarch64-linux-gnusf target. (The "libc" part can affect
the codegen of libcalls: other arches do not use a bare-metal target,
and currently the only fully supported libc on LoongArch is glibc
anyway.)
See: https://lore.kernel.org/loongarch/CAKwvOdnimxv8oJ4mVY74zqtt1x7KTMrWvn2_T9x22SFDbU6rHQ@mail.gmail.com/
Reviewed-by: Nick Desaulniers <[email protected]>
Signed-off-by: WANG Xuerui <[email protected]>
Signed-off-by: Huacai Chen <[email protected]>
|
|
Confirmed working with QEMU system emulation.
Acked-by: Nick Desaulniers <[email protected]>
Signed-off-by: WANG Xuerui <[email protected]>
Signed-off-by: Huacai Chen <[email protected]>
|
|
This is a port of commit 08f6554ff90e ("mips: Include KBUILD_CPPFLAGS in
CHECKFLAGS invocation") to arch/loongarch, for fixing cross-compilation
of Linux/LoongArch with Clang, where previously the `--target` flag
would no longer be present for the CHECKFLAGS cc invocation leading to
build failure.
Reported-by: Nathan Chancellor <[email protected]>
Reviewed-by: Nathan Chancellor <[email protected]>
Link: https://github.com/ClangBuiltLinux/linux/issues/1787#issuecomment-1608306002
Signed-off-by: WANG Xuerui <[email protected]>
Signed-off-by: Huacai Chen <[email protected]>
|
|
This is a port of commit 76d7fff22be3e ("MIPS: VDSO: Use CLANG_FLAGS
instead of filtering out '--target='") to arch/loongarch, for fixing
cross-compilation with Clang.
Reported-by: Nathan Chancellor <[email protected]>
Reviewed-by: Nathan Chancellor <[email protected]>
Link: https://github.com/ClangBuiltLinux/linux/issues/1787#issuecomment-1608306002
Signed-off-by: WANG Xuerui <[email protected]>
Signed-off-by: Huacai Chen <[email protected]>
|
|
Now the arch code is mostly ready for LLVM/Clang consumption, it is time
to re-organize the CFLAGS a little to actually enable the LLVM build.
Namely, all -G0 switches from CFLAGS are removed, and -mexplicit-relocs
and -mdirect-extern-access are now wrapped with cc-option (with the
related asm/percpu.h definition guarded against toolchain combos that
are known to not work).
A build with !RELOCATABLE && !MODULE is confirmed working within a QEMU
environment; support for the two features are currently blocked on
LLVM/Clang, and will come later.
Why -G0 can be removed:
In GCC, -G stands for "small data threshold", that instructs the
compiler to put data smaller than the specified threshold in a dedicated
"small data" section (called .sdata on LoongArch and several other
arches).
However, benefiting from this would require ABI cooperation, which is
not the case for LoongArch; and current GCC behave the same whether -G0
(equal to disabling this optimization) is given or not. So, remove -G0
from CFLAGS altogether for one less thing to care about. This also
benefits LLVM/Clang compatibility where the -G switch is not supported.
Why -mexplicit-relocs can now be conditionally applied without
regressions:
Originally -mexplicit-relocs is unconditionally added to CFLAGS in case
of CONFIG_AS_HAS_EXPLICIT_RELOCS, because not having it (i.e. old GCC +
new binutils) would not work: modules will have R_LARCH_ABS_* relocs
inside, but given the rarity of such toolchain combo in the wild, it may
not be worthwhile to support it, so support for such relocs in modules
were not added back when explicit relocs support was upstreamed, and
-mexplicit-relocs is unconditionally added to fail the build early.
Now that Clang compatibility is desired, given Clang is behaving like
-mexplicit-relocs from day one but without support for the CLI flag, we
must ensure the flag is not passed in case of Clang. However, explicit
compiler flavor checks can be more brittle than feature detection: in
this case what actually matters is support for __attribute__((model))
when building modules. Given neither older GCC nor current Clang support
this attribute, probing for the attribute support and #error'ing out
would allow proper UX without checking for Clang, and also automatically
work when Clang support for the attribute is to be added in the future.
Why -mdirect-extern-access is now conditionally applied:
This is actually a nice-to-have optimization that can reduce GOT
accesses, but not having it is harmless either. Because Clang does not
support the option currently, but might do so in the future, conditional
application via cc-option ensures compatibility with both current and
future Clang versions.
Suggested-by: Xi Ruoyao <[email protected]> # cc-option changes
Signed-off-by: WANG Xuerui <[email protected]>
Signed-off-by: Huacai Chen <[email protected]>
|
|
The invtlb instruction has been supported by upstream LoongArch
toolchains from day one, so ditch the raw opcode trickery and just use
plain inline asm for it.
While at it, also make the invtlb asm statements barriers, for proper
modeling of the side effects. The functions are also marked as
__always_inline instead of just "inline", because they cannot work at
all if not inlined: the op argument will not be compile-time const in
that case, thus failing to satisfy the "i" constraint.
The signature of the other more specific invtlb wrappers contain unused
arguments right now, but these are not removed right away in order for
the patch to be focused. In the meantime, assertions are added to ensure
no accidental misuse happens before the refactor. (The more specific
wrappers cannot re-use the generic invtlb wrapper, because the ISA
manual says $zero shall be used in case a particular op does not take
the respective argument: re-using the generic wrapper would mean losing
control over the register usage.)
Signed-off-by: WANG Xuerui <[email protected]>
Signed-off-by: Huacai Chen <[email protected]>
|
|
In addition to less visual clutter, this also makes Clang happy
regarding the const-ness of arguments. In the original approach, all
Clang gets to see is the incoming arguments whose const-ness cannot be
proven without first being inlined; so Clang errors out here while GCC
is fine.
While at it, tweak several printk format strings because the return type
of csr_read64 becomes effectively unsigned long, instead of unsigned
long long.
Signed-off-by: WANG Xuerui <[email protected]>
Signed-off-by: Huacai Chen <[email protected]>
|
|
The GNU assembler (as of 2.40) mis-treats FCSR operands as GPRs, but
the LLVM IAS does not. Probe for this and refer to FCSRs as "$fcsrNN"
if support is present.
Signed-off-by: WANG Xuerui <[email protected]>
Signed-off-by: Huacai Chen <[email protected]>
|
|
When the kernel is compiled with LLVM, the register names being handled
during exception fixup building are ABI names instead of bare $rNN
style. Add mapping for the ABI names for LLVM compatibility.
Signed-off-by: WANG Rui <[email protected]>
Signed-off-by: WANG Xuerui <[email protected]>
Signed-off-by: Huacai Chen <[email protected]>
|
|
Taking the address delta between symbols in different sections is not
supported by the LLVM IAS. Instead, do this in the linker script, so
the same data can be properly referenced in assembly.
Signed-off-by: WANG Rui <[email protected]>
Signed-off-by: WANG Xuerui <[email protected]>
[chenhuacai: Fix build with !CONFIG_EFI_STUB]
Signed-off-by: Huacai Chen <[email protected]>
|
|
Add guard for the larch_insn_gen_xxx functions to verify whether the
immediate operand is within the acceptable range.
Signed-off-by: WANG Rui <[email protected]>
Signed-off-by: Huacai Chen <[email protected]>
|
|
Debugfs functions are not supposed to be checked for errors. This
is sort of unusual but it is described in the comments for the
debugfs_create_dir() function. Also debugfs_create_dir() can never
return NULL.
Reviewed-by: WANG Xuerui <[email protected]>
Signed-off-by: Dan Carpenter <[email protected]>
Signed-off-by: Huacai Chen <[email protected]>
|
|
ACPI systems set io masters by parsing ACPI MADT, FDT systems have no
MADT so we explicitly set CPU#0 as the io master. Otherwise CPU#0 will
be considered as hotpluggable.
Signed-off-by: Huacai Chen <[email protected]>
|
|
Vladimir Oltean says:
====================
Fix PTP received on wrong port with bridged SJA1105 DSA
Since the changes were made to tag_8021q to support imprecise RX for
bridged ports, the tag_sja1105 driver still prefers the source port
information deduced from the VLAN headers for link-local traffic, even
though the switch can theoretically do better and report the precise
source port.
The problem is that the tagger doesn't know when to trust one source of
information over another, because the INCL_SRCPT option (to "tag" link
local frames) is sometimes enabled and sometimes it isn't.
The first patch makes the switch provide the hardware tag for link local
traffic under all circumstances, and the second patch makes the tagger
always use that hardware tag as primary source of information for link
local packets.
====================
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Paolo Abeni <[email protected]>
|
|
Currently the sja1105 tagging protocol prefers using the source port
information from the VLAN header if that is available, falling back to
the INCL_SRCPT option if it isn't. The VLAN header is available for all
frames except for META frames initiated by the switch (containing RX
timestamps), and thus, the "if (is_link_local)" branch is practically
dead.
The tag_8021q source port identification has become more loose
("imprecise") and will report a plausible rather than exact bridge port,
when under a bridge (be it VLAN-aware or VLAN-unaware). But link-local
traffic always needs to know the precise source port. With incorrect
source port reporting, for example PTP traffic over 2 bridged ports will
all be seen on sockets opened on the first such port, which is incorrect.
Now that the tagging protocol has been changed to make link-local frames
always contain source port information, we can reverse the order of the
checks so that we always give precedence to that information (which is
always precise) in lieu of the tag_8021q VID which is only precise for a
standalone port.
Fixes: d7f9787a763f ("net: dsa: tag_8021q: add support for imprecise RX based on the VBID")
Fixes: 91495f21fcec ("net: dsa: tag_8021q: replace the SVL bridging with VLAN-unaware IVL bridging")
Signed-off-by: Vladimir Oltean <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
|
|
Link-local traffic on bridged SJA1105 ports is sometimes tagged by the
hardware with source port information (when the port is under a VLAN
aware bridge).
The tag_8021q source port identification has become more loose
("imprecise") and will report a plausible rather than exact bridge port,
when under a bridge (be it VLAN-aware or VLAN-unaware). But link-local
traffic always needs to know the precise source port.
Modify the driver logic (and therefore: the tagging protocol itself) to
always include the source port information with link-local packets,
regardless of whether the port is standalone, under a VLAN-aware or
VLAN-unaware bridge. This makes it possible for the tagging driver to
give priority to that information over the tag_8021q VLAN header.
The big drawback with INCL_SRCPT is that it makes it impossible to
distinguish between an original MAC DA of 01:80:C2:XX:YY:ZZ and
01:80:C2:AA:BB:ZZ, because the tagger just patches MAC DA bytes 3 and 4
with zeroes. Only if PTP RX timestamping is enabled, the switch will
generate a META follow-up frame containing the RX timestamp and the
original bytes 3 and 4 of the MAC DA. Those will be used to patch up the
original packet. Nonetheless, in the absence of PTP RX timestamping, we
have to live with this limitation, since it is more important to have
the more precise source port information for link-local traffic.
Fixes: d7f9787a763f ("net: dsa: tag_8021q: add support for imprecise RX based on the VBID")
Fixes: 91495f21fcec ("net: dsa: tag_8021q: replace the SVL bridging with VLAN-unaware IVL bridging")
Signed-off-by: Vladimir Oltean <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
|
|
Vladimir Oltean says:
====================
Fix PTP packet drops with ocelot-8021q DSA tag protocol
Changes in v2:
- Distinguish between L2 and L4 PTP packets
v1 at:
https://lore.kernel.org/netdev/[email protected]/
Patch 3/3 fixes an issue with the ocelot/felix driver, where it would
drop PTP traffic on RX unless hardware timestamping for that packet type
was enabled.
Fixing that requires the driver to know whether it had previously
configured the hardware to timestamp PTP packets on that port. But it
cannot correctly determine that today using the existing code structure,
so patches 1/3 and 2/3 fix the control path of the code such that
ocelot->ports[port]->trap_proto faithfully reflects whether that
configuration took place.
====================
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Paolo Abeni <[email protected]>
|
|
is disabled
The driver implements a workaround for the fact that it doesn't have an
IRQ source to tell it whether PTP frames are available through the
extraction registers, for those frames to be processed and passed
towards the network stack. That workaround is to configure the switch,
through felix_hwtstamp_set() -> felix_update_trapping_destinations(),
to create two copies of PTP packets: one sent over Ethernet to the DSA
master, and one to be consumed through the aforementioned CPU extraction
queue registers.
The reason why we want PTP packets to be consumed through the CPU
extraction registers in the first place is because we want to see their
hardware RX timestamp. With tag_8021q, that is only visible that way,
and it isn't visible with the copy of the packet that's transmitted over
Ethernet.
The problem with the workaround implementation is that it drops the
packet received over Ethernet, in expectation of its copy being present
in the CPU extraction registers. However, if felix_hwtstamp_set() hasn't
run (aka PTP RX timestamping is disabled), the driver will drop the
original PTP frame and there will be no copy of it in the CPU extraction
registers. So, the network stack will simply not see any PTP frame.
Look at the port's trapping configuration to see whether the driver has
previously enabled the CPU extraction registers. If it hasn't, just
don't RX timestamp the frame and let it be passed up the stack by DSA,
which is perfectly fine.
Fixes: 0a6f17c6ae21 ("net: dsa: tag_ocelot_8021q: add support for PTP timestamping")
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
|
|
In a future change, the driver will need to determine whether PTP RX
timestamping is enabled on a port (including whether traps were set up
on that port in particular) and that is currently not possible.
The driver supports different RX filters (L2, L4) and kinds of TX
timestamping (one-step, two-step) on its ports, but it saves all
configuration in a single struct hwtstamp_config that is global to the
switch. So, the latest timestamping configuration on one port
(including a request to disable timestamping) affects what gets reported
for all ports, even though the configuration itself is still individual
to each port.
The port timestamping configurations are only coupled because of the
common structure, so replace the hwtstamp_config with a mask of trapped
protocols saved per port. We also have the ptp_cmd to distinguish
between one-step and two-step PTP timestamping, so with those 2 bits of
information we can fully reconstruct a descriptive struct
hwtstamp_config for each port, during the SIOCGHWTSTAMP ioctl.
Fixes: 4e3b0468e6d7 ("net: mscc: PTP Hardware Clock (PHC) support")
Fixes: 96ca08c05838 ("net: mscc: ocelot: set up traps for PTP packets")
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
|
|
PTP RX timestamping should be enabled when the user requests it, not by
default. If it is enabled by default, it can be problematic when the
ocelot driver is a DSA master, and it sidesteps what DSA tries to avoid
through __dsa_master_hwtstamp_validate().
Additionally, after the change which made ocelot trap PTP packets only
to the CPU at ocelot_hwtstamp_set() time, it is no longer even true that
RX timestamping is enabled by default, because until ocelot_hwtstamp_set()
is called, the PTP traps are actually not set up. So the rx_filter field
of ocelot->hwtstamp_config reflects an incorrect reality.
Fixes: 96ca08c05838 ("net: mscc: ocelot: set up traps for PTP packets")
Fixes: 4e3b0468e6d7 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
|
|
The FFR is a predicate register which can vary between 16 and 256 bits
in size depending upon the configured vector length. When saving the
SVE state in streaming SVE mode, the FFR register is inaccessible and
so commit 9f5848665788 ("arm64/sve: Make access to FFR optional") simply
clears the FFR field of the in-memory context structure. Unfortunately,
it achieves this using an unconditional 8-byte store and so if the SME
vector length is anything other than 64 bytes in size we will either
fail to clear the entire field or, worse, we will corrupt memory
immediately following the structure. This has led to intermittent kfence
splats in CI [1] and can trigger kmalloc Redzone corruption messages
when running the 'fp-stress' kselftest:
| =============================================================================
| BUG kmalloc-1k (Not tainted): kmalloc Redzone overwritten
| -----------------------------------------------------------------------------
|
| 0xffff000809bf1e22-0xffff000809bf1e27 @offset=7714. First byte 0x0 instead of 0xcc
| Allocated in do_sme_acc+0x9c/0x220 age=2613 cpu=1 pid=531
| __kmalloc+0x8c/0xcc
| do_sme_acc+0x9c/0x220
| ...
Replace the 8-byte store with a store of a predicate register which has
been zero-initialised with PFALSE, ensuring that the entire field is
cleared in memory.
[1] https://lore.kernel.org/r/CA+G9fYtU7HsV0R0dp4XEH5xXHSJFw8KyDf5VQrLLfMxWfxQkag@mail.gmail.com
Cc: Mark Brown <[email protected]>
Cc: Mark Rutland <[email protected]>
Cc: Naresh Kamboju <[email protected]>
Fixes: 9f5848665788 ("arm64/sve: Make access to FFR optional")
Reported-by: Linux Kernel Functional Testing <[email protected]>
Signed-off-by: Will Deacon <[email protected]>
Reviewed-by: Mark Brown <[email protected]>
Tested-by: Anders Roxell <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Catalin Marinas <[email protected]>
|
|
Florian Westphal says:
====================
net/sched: act_ipt bug fixes
v3: prefer skb_header() helper in patch 2. No other changes.
I've retained Acks and RvB-Tags of v2.
While checking if netfilter could be updated to replace selected
instances of NF_DROP with kfree_skb_reason+NF_STOLEN to improve
debugging info via drop monitor I found that act_ipt is incompatible
with such an approach. Moreover, it lacks multiple sanity checks
to avoid certain code paths that make assumptions that the tc layer
doesn't meet, such as header sanity checks, availability of skb_dst,
skb_nfct() and so on.
act_ipt test in the tc selftest still pass with this applied.
I think that we should consider removal of this module, while
this should take care of all problems, its ipv4 only and I don't
think there are any netfilter targets that lack a native tc
equivalent, even when ignoring bpf.
====================
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Paolo Abeni <[email protected]>
|
|
xtables relies on skb being owned by ip stack, i.e. with ipv4
check in place skb->cb is supposed to be IPCB.
I don't see an immediate problem (REJECT target cannot be used anymore
now that PRE/POSTROUTING hook validation has been fixed), but better be
safe than sorry.
A much better patch would be to either mark act_ipt as
"depends on BROKEN" or remove it altogether. I plan to do this
for -next in the near future.
This tc extension is broken in the sense that tc lacks an
equivalent of NF_STOLEN verdict.
With NF_STOLEN, target function takes complete ownership of skb, caller
cannot dereference it anymore.
ACT_STOLEN cannot be used for this: it has a different meaning, caller
is allowed to dereference the skb.
At this time NF_STOLEN won't be returned by any targets as far as I can
see, but this may change in the future.
It might be possible to work around this via list of allowed
target extensions known to only return DROP or ACCEPT verdicts, but this
is error prone/fragile.
Existing selftest only validates xt_LOG and act_ipt is restricted
to ipv4 so I don't think this action is used widely.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Florian Westphal <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Acked-by: Jamal Hadi Salim <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
|
|
Netfilter targets make assumptions on the skb state, for example
iphdr is supposed to be in the linear area.
This is normally done by IP stack, but in act_ipt case no
such checks are made.
Some targets can even assume that skb_dst will be valid.
Make a minimum effort to check for this:
- Don't call the targets eval function for non-ipv4 skbs.
- Don't call the targets eval function for POSTROUTING
emulation when the skb has no dst set.
v3: use skb_protocol helper (Davide Caratti)
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Florian Westphal <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Acked-by: Jamal Hadi Salim <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
|
|
Looks like "tc" hard-codes "mangle" as the only supported table
name, but on kernel side there are no checks.
This is wrong. Not all xtables targets are safe to call from tc.
E.g. "nat" targets assume skb has a conntrack object assigned to it.
Normally those get called from netfilter nat core which consults the
nat table to obtain the address mapping.
"tc" userspace either sets PRE or POSTROUTING as hook number, but there
is no validation of this on kernel side, so update netlink policy to
reject bogus numbers. Some targets may assume skb_dst is set for
input/forward hooks, so prevent those from being used.
act_ipt uses the hook number in two places:
1. the state hook number, this is fine as-is
2. to set par.hook_mask
The latter is a bit mask, so update the assignment to make
xt_check_target() to the right thing.
Followup patch adds required checks for the skb/packet headers before
calling the targets evaluation function.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Florian Westphal <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Acked-by: Jamal Hadi Salim <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
|
|
As &net->sctp.addr_wq_lock is also acquired by the timer
sctp_addr_wq_timeout_handler() in protocal.c, the same lock acquisition
at sctp_auto_asconf_init() seems should disable irq since it is called
from sctp_accept() under process context.
Possible deadlock scenario:
sctp_accept()
-> sctp_sock_migrate()
-> sctp_auto_asconf_init()
-> spin_lock(&net->sctp.addr_wq_lock)
<timer interrupt>
-> sctp_addr_wq_timeout_handler()
-> spin_lock_bh(&net->sctp.addr_wq_lock); (deadlock here)
This flaw was found using an experimental static analysis tool we are
developing for irq-related deadlock.
The tentative patch fix the potential deadlock by spin_lock_bh().
Signed-off-by: Chengfeng Ye <[email protected]>
Fixes: 34e5b0118685 ("sctp: delay auto_asconf init until binding the first addr")
Acked-by: Xin Long <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Paolo Abeni <[email protected]>
|
|
dev_set_rx_mode() grabs a spin_lock, and the lan743x implementation
proceeds subsequently to go to sleep using readx_poll_timeout().
Introduce a helper wrapping the readx_poll_timeout_atomic() function
and use it to replace the calls to readx_polL_timeout().
Fixes: 23f0703c125b ("lan743x: Add main source files for new lan743x driver")
Cc: [email protected]
Cc: Bryan Whitehead <[email protected]>
Cc: [email protected]
Signed-off-by: Moritz Fischer <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Paolo Abeni <[email protected]>
|
|
Clang-16 produces this warning, which is fatal with CONFIG_WERROR:
../drivers/media/radio/wl128x/fmdrv_common.c:1237:19: error: variable 'cmd_cnt' set but not used [-Werror,-Wunused-but-set-variable]
int ret, fw_len, cmd_cnt;
^
1 error generated.
What happens is that cmd_cnt tracks the amount of firmware data packets
were transfered, which is printed only when debug is used.
Switch to use the firmware count, as the message is all about reporting
a partial firmware transfer.
Link: https://lore.kernel.org/linux-media/6badd27ebfa718d5737f517f18b29a3e0f6e43f8.1687981726.git.mchehab@kernel.org
Signed-off-by: Mauro Carvalho Chehab <[email protected]>
|
|
clang warns about a possible field overflow in a memcpy:
In file included from fs/smb/server/smb_common.c:7:
include/linux/fortify-string.h:583:4: error: call to '__write_overflow_field' declared with 'warning' attribute: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Werror,-Wattribute-warning]
__write_overflow_field(p_size_field, size);
It appears to interpret the "&out[baselen + 4]" as referring to a single
byte of the character array, while the equivalen "out + baselen + 4" is
seen as an offset into the array.
I don't see that kind of warning elsewhere, so just go with the simple
rework.
Fixes: e2f34481b24d ("cifsd: add server-side procedures for SMB3")
Signed-off-by: Arnd Bergmann <[email protected]>
Acked-by: Namjae Jeon <[email protected]>
Signed-off-by: Steve French <[email protected]>
|
|
This modifies our user mode stack expansion code to always take the
mmap_lock for writing before modifying the VM layout.
It's actually something we always technically should have done, but
because we didn't strictly need it, we were being lazy ("opportunistic"
sounds so much better, doesn't it?) about things, and had this hack in
place where we would extend the stack vma in-place without doing the
proper locking.
And it worked fine. We just needed to change vm_start (or, in the case
of grow-up stacks, vm_end) and together with some special ad-hoc locking
using the anon_vma lock and the mm->page_table_lock, it all was fairly
straightforward.
That is, it was all fine until Ruihan Li pointed out that now that the
vma layout uses the maple tree code, we *really* don't just change
vm_start and vm_end any more, and the locking really is broken. Oops.
It's not actually all _that_ horrible to fix this once and for all, and
do proper locking, but it's a bit painful. We have basically three
different cases of stack expansion, and they all work just a bit
differently:
- the common and obvious case is the page fault handling. It's actually
fairly simple and straightforward, except for the fact that we have
something like 24 different versions of it, and you end up in a maze
of twisty little passages, all alike.
- the simplest case is the execve() code that creates a new stack.
There are no real locking concerns because it's all in a private new
VM that hasn't been exposed to anybody, but lockdep still can end up
unhappy if you get it wrong.
- and finally, we have GUP and page pinning, which shouldn't really be
expanding the stack in the first place, but in addition to execve()
we also use it for ptrace(). And debuggers do want to possibly access
memory under the stack pointer and thus need to be able to expand the
stack as a special case.
None of these cases are exactly complicated, but the page fault case in
particular is just repeated slightly differently many many times. And
ia64 in particular has a fairly complicated situation where you can have
both a regular grow-down stack _and_ a special grow-up stack for the
register backing store.
So to make this slightly more manageable, the bulk of this series is to
first create a helper function for the most common page fault case, and
convert all the straightforward architectures to it.
Thus the new 'lock_mm_and_find_vma()' helper function, which ends up
being used by x86, arm, powerpc, mips, riscv, alpha, arc, csky, hexagon,
loongarch, nios2, sh, sparc32, and xtensa. So we not only convert more
than half the architectures, we now have more shared code and avoid some
of those twisty little passages.
And largely due to this common helper function, the full diffstat of
this series ends up deleting more lines than it adds.
That still leaves eight architectures (ia64, m68k, microblaze, openrisc,
parisc, s390, sparc64 and um) that end up doing 'expand_stack()'
manually because they are doing something slightly different from the
normal pattern. Along with the couple of special cases in execve() and
GUP.
So there's a couple of patches that first create 'locked' helper
versions of the stack expansion functions, so that there's a obvious
path forward in the conversion. The execve() case is then actually
pretty simple, and is a nice cleanup from our old "grow-up stackls are
special, because at execve time even they grow down".
The #ifdef CONFIG_STACK_GROWSUP in that code just goes away, because
it's just more straightforward to write out the stack expansion there
manually, instead od having get_user_pages_remote() do it for us in some
situations but not others and have to worry about locking rules for GUP.
And the final step is then to just convert the remaining odd cases to a
new world order where 'expand_stack()' is called with the mmap_lock held
for reading, but where it might drop it and upgrade it to a write, only
to return with it held for reading (in the success case) or with it
completely dropped (in the failure case).
In the process, we remove all the stack expansion from GUP (where
dropping the lock wouldn't be ok without special rules anyway), and add
it in manually to __access_remote_vm() for ptrace().
Thanks to Adrian Glaubitz and Frank Scheiner who tested the ia64 cases.
Everything else here felt pretty straightforward, but the ia64 rules for
stack expansion are really quite odd and very different from everything
else. Also thanks to Vegard Nossum who caught me getting one of those
odd conditions entirely the wrong way around.
Anyway, I think I want to actually move all the stack expansion code to
a whole new file of its own, rather than have it split up between
mm/mmap.c and mm/memory.c, but since this will have to be backported to
the initial maple tree vma introduction anyway, I tried to keep the
patches _fairly_ minimal.
Also, while I don't think it's valid to expand the stack from GUP, the
final patch in here is a "warn if some crazy GUP user wants to try to
expand the stack" patch. That one will be reverted before the final
release, but it's left to catch any odd cases during the merge window
and release candidates.
Reported-by: Ruihan Li <[email protected]>
* branch 'expand-stack':
gup: add warning if some caller would seem to want stack expansion
mm: always expand the stack with the mmap write lock held
execve: expand new process stack manually ahead of time
mm: make find_extend_vma() fail if write lock not held
powerpc/mm: convert coprocessor fault to lock_mm_and_find_vma()
mm/fault: convert remaining simple cases to lock_mm_and_find_vma()
arm/mm: Convert to using lock_mm_and_find_vma()
riscv/mm: Convert to using lock_mm_and_find_vma()
mips/mm: Convert to using lock_mm_and_find_vma()
powerpc/mm: Convert to using lock_mm_and_find_vma()
arm64/mm: Convert to using lock_mm_and_find_vma()
mm: make the page fault mmap locking killable
mm: introduce new 'lock_mm_and_find_vma()' page fault helper
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking changes from Jakub Kicinski:
"WiFi 7 and sendpage changes are the biggest pieces of work for this
release. The latter will definitely require fixes but I think that we
got it to a reasonable point.
Core:
- Rework the sendpage & splice implementations
Instead of feeding data into sockets page by page extend sendmsg
handlers to support taking a reference on the data, controlled by a
new flag called MSG_SPLICE_PAGES
Rework the handling of unexpected-end-of-file to invoke an
additional callback instead of trying to predict what the right
combination of MORE/NOTLAST flags is
Remove the MSG_SENDPAGE_NOTLAST flag completely
- Implement SCM_PIDFD, a new type of CMSG type analogous to
SCM_CREDENTIALS, but it contains pidfd instead of plain pid
- Enable socket busy polling with CONFIG_RT
- Improve reliability and efficiency of reporting for ref_tracker
- Auto-generate a user space C library for various Netlink families
Protocols:
- Allow TCP to shrink the advertised window when necessary, prevent
sk_rcvbuf auto-tuning from growing the window all the way up to
tcp_rmem[2]
- Use per-VMA locking for "page-flipping" TCP receive zerocopy
- Prepare TCP for device-to-device data transfers, by making sure
that payloads are always attached to skbs as page frags
- Make the backoff time for the first N TCP SYN retransmissions
linear. Exponential backoff is unnecessarily conservative
- Create a new MPTCP getsockopt to retrieve all info
(MPTCP_FULL_INFO)
- Avoid waking up applications using TLS sockets until we have a full
record
- Allow using kernel memory for protocol ioctl callbacks, paving the
way to issuing ioctls over io_uring
- Add nolocalbypass option to VxLAN, forcing packets to be fully
encapsulated even if they are destined for a local IP address
- Make TCPv4 use consistent hash in TIME_WAIT and SYN_RECV. Ensure
in-kernel ECMP implementation (e.g. Open vSwitch) select the same
link for all packets. Support L4 symmetric hashing in Open vSwitch
- PPPoE: make number of hash bits configurable
- Allow DNS to be overwritten by DHCPACK in the in-kernel DHCP client
(ipconfig)
- Add layer 2 miss indication and filtering, allowing higher layers
(e.g. ACL filters) to make forwarding decisions based on whether
packet matched forwarding state in lower devices (bridge)
- Support matching on Connectivity Fault Management (CFM) packets
- Hide the "link becomes ready" IPv6 messages by demoting their
printk level to debug
- HSR: don't enable promiscuous mode if device offloads the proto
- Support active scanning in IEEE 802.15.4
- Continue work on Multi-Link Operation for WiFi 7
BPF:
- Add precision propagation for subprogs and callbacks. This allows
maintaining verification efficiency when subprograms are used, or
in fact passing the verifier at all for complex programs,
especially those using open-coded iterators
- Improve BPF's {g,s}setsockopt() length handling. Previously BPF
assumed the length is always equal to the amount of written data.
But some protos allow passing a NULL buffer to discover what the
output buffer *should* be, without writing anything
- Accept dynptr memory as memory arguments passed to helpers
- Add routing table ID to bpf_fib_lookup BPF helper
- Support O_PATH FDs in BPF_OBJ_PIN and BPF_OBJ_GET commands
- Drop bpf_capable() check in BPF_MAP_FREEZE command (used to mark
maps as read-only)
- Show target_{obj,btf}_id in tracing link fdinfo
- Addition of several new kfuncs (most of the names are
self-explanatory):
- Add a set of new dynptr kfuncs: bpf_dynptr_adjust(),
bpf_dynptr_is_null(), bpf_dynptr_is_rdonly(), bpf_dynptr_size()
and bpf_dynptr_clone().
- bpf_task_under_cgroup()
- bpf_sock_destroy() - force closing sockets
- bpf_cpumask_first_and(), rework bpf_cpumask_any*() kfuncs
Netfilter:
- Relax set/map validation checks in nf_tables. Allow checking
presence of an entry in a map without using the value
- Increase ip_vs_conn_tab_bits range for 64BIT builds
- Allow updating size of a set
- Improve NAT tuple selection when connection is closing
Driver API:
- Integrate netdev with LED subsystem, to allow configuring HW
"offloaded" blinking of LEDs based on link state and activity
(i.e. packets coming in and out)
- Support configuring rate selection pins of SFP modules
- Factor Clause 73 auto-negotiation code out of the drivers, provide
common helper routines
- Add more fool-proof helpers for managing lifetime of MDIO devices
associated with the PCS layer
- Allow drivers to report advanced statistics related to Time Aware
scheduler offload (taprio)
- Allow opting out of VF statistics in link dump, to allow more VFs
to fit into the message
- Split devlink instance and devlink port operations
New hardware / drivers:
- Ethernet:
- Synopsys EMAC4 IP support (stmmac)
- Marvell 88E6361 8 port (5x1GE + 3x2.5GE) switches
- Marvell 88E6250 7 port switches
- Microchip LAN8650/1 Rev.B0 PHYs
- MediaTek MT7981/MT7988 built-in 1GE PHY driver
- WiFi:
- Realtek RTL8192FU, 2.4 GHz, b/g/n mode, 2T2R, 300 Mbps
- Realtek RTL8723DS (SDIO variant)
- Realtek RTL8851BE
- CAN:
- Fintek F81604
Drivers:
- Ethernet NICs:
- Intel (100G, ice):
- support dynamic interrupt allocation
- use meta data match instead of VF MAC addr on slow-path
- nVidia/Mellanox:
- extend link aggregation to handle 4, rather than just 2 ports
- spawn sub-functions without any features by default
- OcteonTX2:
- support HTB (Tx scheduling/QoS) offload
- make RSS hash generation configurable
- support selecting Rx queue using TC filters
- Wangxun (ngbe/txgbe):
- add basic Tx/Rx packet offloads
- add phylink support (SFP/PCS control)
- Freescale/NXP (enetc):
- report TAPRIO packet statistics
- Solarflare/AMD:
- support matching on IP ToS and UDP source port of outer
header
- VxLAN and GENEVE tunnel encapsulation over IPv4 or IPv6
- add devlink dev info support for EF10
- Virtual NICs:
- Microsoft vNIC:
- size the Rx indirection table based on requested
configuration
- support VLAN tagging
- Amazon vNIC:
- try to reuse Rx buffers if not fully consumed, useful for ARM
servers running with 16kB pages
- Google vNIC:
- support TCP segmentation of >64kB frames
- Ethernet embedded switches:
- Marvell (mv88e6xxx):
- enable USXGMII (88E6191X)
- Microchip:
- lan966x: add support for Egress Stage 0 ACL engine
- lan966x: support mapping packet priority to internal switch
priority (based on PCP or DSCP)
- Ethernet PHYs:
- Broadcom PHYs:
- support for Wake-on-LAN for BCM54210E/B50212E
- report LPI counter
- Microsemi PHYs: support RGMII delay configuration (VSC85xx)
- Micrel PHYs: receive timestamp in the frame (LAN8841)
- Realtek PHYs: support optional external PHY clock
- Altera TSE PCS: merge the driver into Lynx PCS which it is a
variant of
- CAN: Kvaser PCIEcan:
- support packet timestamping
- WiFi:
- Intel (iwlwifi):
- major update for new firmware and Multi-Link Operation (MLO)
- configuration rework to drop test devices and split the
different families
- support for segmented PNVM images and power tables
- new vendor entries for PPAG (platform antenna gain) feature
- Qualcomm 802.11ax (ath11k):
- Multiple Basic Service Set Identifier (MBSSID) and Enhanced
MBSSID Advertisement (EMA) support in AP mode
- support factory test mode
- RealTek (rtw89):
- add RSSI based antenna diversity
- support U-NII-4 channels on 5 GHz band
- RealTek (rtl8xxxu):
- AP mode support for 8188f
- support USB RX aggregation for the newer chips"
* tag 'net-next-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1602 commits)
net: scm: introduce and use scm_recv_unix helper
af_unix: Skip SCM_PIDFD if scm->pid is NULL.
net: lan743x: Simplify comparison
netlink: Add __sock_i_ino() for __netlink_diag_dump().
net: dsa: avoid suspicious RCU usage for synced VLAN-aware MAC addresses
Revert "af_unix: Call scm_recv() only after scm_set_cred()."
phylink: ReST-ify the phylink_pcs_neg_mode() kdoc
libceph: Partially revert changes to support MSG_SPLICE_PAGES
net: phy: mscc: fix packet loss due to RGMII delays
net: mana: use vmalloc_array and vcalloc
net: enetc: use vmalloc_array and vcalloc
ionic: use vmalloc_array and vcalloc
pds_core: use vmalloc_array and vcalloc
gve: use vmalloc_array and vcalloc
octeon_ep: use vmalloc_array and vcalloc
net: usb: qmi_wwan: add u-blox 0x1312 composition
perf trace: fix MSG_SPLICE_PAGES build error
ipvlan: Fix return value of ipvlan_queue_xmit()
netfilter: nf_tables: fix underflow in chain reference counter
netfilter: nf_tables: unbind non-anonymous set if rule construction fails
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux
Pull sysctl updates from Luis Chamberlain:
"The changes for sysctl are in line with prior efforts to stop usage of
deprecated routines which incur recursion and also make it hard to
remove the empty array element in each sysctl array declaration.
The most difficult user to modify was parport which required a bit of
re-thinking of how to declare shared sysctls there, Joel Granados has
stepped up to the plate to do most of this work and eventual removal
of register_sysctl_table(). That work ended up saving us about 1465
bytes according to bloat-o-meter. Since we gained a few bloat-o-meter
karma points I moved two rather small sysctl arrays from
kernel/sysctl.c leaving us only two more sysctl arrays to move left.
Most changes have been tested on linux-next for about a month. The
last straggler patches are a minor parport fix, changes to the sysctl
kernel selftest so to verify correctness and prevent regressions for
the future change he made to provide an alternative solution for the
special sysctl mount point target which was using the now deprecated
sysctl child element.
This is all prep work to now finally be able to remove the empty array
element in all sysctl declarations / registrations which is expected
to save us a bit of bytes all over the kernel. That work will be
tested early after v6.5-rc1 is out"
* tag 'v6.5-rc1-sysctl-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux:
sysctl: replace child with an enumeration
sysctl: Remove debugging dump_stack
test_sysclt: Test for registering a mount point
test_sysctl: Add an option to prevent test skip
test_sysctl: Add an unregister sysctl test
test_sysctl: Group node sysctl test under one func
test_sysctl: Fix test metadata getters
parport: plug a sysctl register leak
sysctl: move security keys sysctl registration to its own file
sysctl: move umh sysctl registration to its own file
signal: move show_unhandled_signals sysctl to its own file
sysctl: remove empty dev table
sysctl: Remove register_sysctl_table
sysctl: Refactor base paths registrations
sysctl: stop exporting register_sysctl_table
parport: Removed sysctl related defines
parport: Remove register_sysctl_table from parport_default_proc_register
parport: Remove register_sysctl_table from parport_device_proc_register
parport: Remove register_sysctl_table from parport_proc_register
parport: Move magic number "15" to a define
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux
Pull module updates from Luis Chamberlain:
"The changes queued up for modules are pretty tame, mostly code removal
of moving of code.
Only two minor functional changes are made, the only one which stands
out is Sebastian Andrzej Siewior's simplification of module reference
counting by removing preempt_disable() and that has been tested on
linux-next for well over a month without no regressions.
I'm now, I guess, also a kitchen sink for some kallsyms changes"
[ There was a mis-communication about the concurrent module load changes
that I had expected to come through Luis despite me authoring the
patch. So some of the module updates were left hanging in the email
ether, and I just committed them separately.
It's my bad - I should have made it more clear that I expected my
own patches to come through the module tree too. Now they missed
linux-next, but hopefully that won't cause any issues - Linus ]
* tag 'v6.5-rc1-modules-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux:
kallsyms: make kallsyms_show_value() as generic function
kallsyms: move kallsyms_show_value() out of kallsyms.c
kallsyms: remove unsed API lookup_symbol_attrs
kallsyms: remove unused arch_get_kallsym() helper
module: Remove preempt_disable() from module reference counting.
|
|
This is the new-and-improved attempt at avoiding huge memory load spikes
when the user space boot sequence tries to load hundreds (or even
thousands) of redundant duplicate modules in parallel.
See commit 9828ed3f695a ("module: error out early on concurrent load of
the same module file") for background and an earlier failed attempt that
was reverted.
That earlier attempt just said "concurrently loading the same module is
silly, just open the module file exclusively and return -ETXTBSY if
somebody else is already loading it".
While it is true that concurrent module loads of the same module is
silly, the reason that earlier attempt then failed was that the
concurrently loaded module would often be a prerequisite for another
module.
Thus failing to load the prerequisite would then cause cascading
failures of the other modules, rather than just short-circuiting that
one unnecessary module load.
At the same time, we still really don't want to load the contents of the
same module file hundreds of times, only to then wait for an eventually
successful load, and have everybody else return -EEXIST.
As a result, this takes another approach, and treats concurrent module
loads from the same file as "idempotent" in the inode. So if one module
load is ongoing, we don't start a new one, but instead just wait for the
first one to complete and return the same return value as it did.
So unlike the first attempt, this does not return early: the intent is
not to speed up the boot, but to avoid a thundering herd problem in
allocating memory (both physical and virtual) for a module more than
once.
Also note that this does change behavior: it used to be that when you
had concurrent loads, you'd have one "winner" that would return success,
and everybody else would return -EEXIST.
In contrast, this idempotent logic goes all Oprah on the problem, and
says "You are a winner! And you are a winner! We are ALL winners". But
since there's no possible actual real semantic difference between "you
loaded the module" and "somebody else already loaded the module", this
is more of a feel-good change than an actual honest-to-goodness semantic
change.
Of course, any true Johnny-come-latelies that don't get caught in the
concurrency filter will still return -EEXIST. It's no different from
not even getting a seat at an Oprah taping. That's life.
See the long thread on the kernel mailing list about this all, which
includes some numbers for memory use before and after the patch.
Link: https://lore.kernel.org/lkml/[email protected]/
Reviewed-by: Johan Hovold <[email protected]>
Tested-by: Johan Hovold <[email protected]>
Tested-by: Luis Chamberlain <[email protected]>
Tested-by: Dan Williams <[email protected]>
Tested-by: Rudi Heitbaum <[email protected]>
Tested-by: David Hildenbrand <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
This will simplify the next step, where we can then key off the inode to
do one idempotent module load.
Let's do the obvious re-organization in one step, and then the new code
in another.
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Drivers can poll requests directly, so use that. We just need to ensure
the driver's request was allocated from a polled hctx, so a special
driver flag is added to struct io_uring_cmd.
The allows unshared and multipath namespaces to use the same polling
callback, and multipath is guaranteed to get the same queue as the
command was submitted on. Previously multipath polling might check a
different path and poll the wrong info.
The other bonus is we don't need a bio payload in order to poll,
allowing commands like 'flush' and 'write zeroes' to be submitted on the
same high priority queue as read and write commands.
Finally, using the request based polling skips the unnecessary bio
overhead.
Signed-off-by: Keith Busch <[email protected]>
Reviewed-by: Sagi Grimberg <[email protected]>
Reviewed-by: Christoph Hellwig <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jens Axboe <[email protected]>
|
|
Provide a direct request polling will for drivers. The interface does
not require a bio, and can skip the overhead associated with polling
those. The biggest gain from skipping the relatively expensive xarray
lookup unnecessary when you already have the request.
With this, the simple rq/qc conversion functions have only one caller
each, so open code this and remove the helpers.
Signed-off-by: Keith Busch <[email protected]>
Reviewed-by: Kanchan Joshi <[email protected]>
Reviewed-by: Sagi Grimberg <[email protected]>
Reviewed-by: Christoph Hellwig <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jens Axboe <[email protected]>
|
|
* for-6.5/block-late:
blk-sysfs: add a new attr_group for blk_mq
blk-iocost: move wbt_enable/disable_default() out of spinlock
blk-wbt: cleanup rwb_enabled() and wbt_disabled()
blk-wbt: remove dead code to handle wbt enable/disable with io inflight
blk-wbt: don't create wbt sysfs entry if CONFIG_BLK_WBT is disabled
blk-mq: fix two misuses on RQF_USE_SCHED
blk-throttle: Fix io statistics for cgroup v1
bcache: Fix bcache device claiming
bcache: Alloc holder object before async registration
raid10: avoid spin_lock from fastpath from raid10_unplug()
md: fix 'delete_mutex' deadlock
md: use mddev->external to select holder in export_rdev()
md/raid1-10: fix casting from randomized structure in raid1_submit_write()
md/raid10: fix the condition to call bio_end_io_acct()
|
|
Pull MMC updates from Ulf Hansson:
"MMC core:
- Allow synchronous detection of (e)MMC/SD/SDIO cards
- Fixup error check for ioctls for SPI hosts
- Disable broken SD-Cache support for Kingston Canvas Go Plus from 2019
- Disable broken eMMC-Trim support for Kingston EMMC04G-M627
- Disable broken eMMC-Trim support for Micron MTFC4GACAJCN-1M
MMC host:
- bcm2835: Convert DT bindings to YAML
- mmci:
- Enable asynchronous probe
- Transform the ux500 HW-busy detection into a proper state machine
- Add support for SW busy-end timeouts for the ux500 variants
- mmci_stm32:
- Add support for sdm32 variant revision v3.0 used on STM32MP25
- Improve the tuning sequence
- mtk-sd: Tune polling-period to improve performance
- sdhci: Fixup DMA configuration for 64-bit DMA mode
- sdhci-bcm-kona: Convert DT bindings to YAML
- sdhci-msm:
- Switch to use the new ICE API
- Add support for the SC8280XP/IPQ6018/QDU1000/QRU1000 variants
- sdhci-pci-gli:
- Add support SD Express cards for GL9767
- Add support for the Genesys Logic GL9767 variant"
* tag 'mmc-v6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (42 commits)
dt-bindings: mmc: fsl-imx-esdhc: Add imx6ul support
mmc: mmci: Add support for SW busy-end timeouts
mmc: Add MMC_QUIRK_BROKEN_SD_CACHE for Kingston Canvas Go Plus from 11/2019
mmc: core: disable TRIM on Kingston EMMC04G-M627
mmc: mmci: stm32: add delay block support for STM32MP25
mmc: mmci: stm32: prepare other delay block support
mmc: mmci: stm32: manage block gap hardware flow control
mmc: mmci: Add support for sdmmc variant revision v3.0
mmc: mmci: add stm32_idmabsize_align parameter
dt-bindings: mmc: mmci: Add st,stm32mp25-sdmmc2 compatible
mmc: core: disable TRIM on Micron MTFC4GACAJCN-1M
mmc: mmci: Break out a helper function
mmc: mmci: Use a switch statement machine
mmc: mmci: Use state machine state as exit condition
mmc: mmci: Retry the busy start condition
mmc: mmci: Make busy complete state machine explicit
mmc: mmci: Break out error check in busy detect
mmc: mmci: Stash status while waiting for busy
mmc: mmci: Unwind big if() clause
mmc: mmci: Clear busy_status when starting command
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd updates from
"Core MTD changes:
- otp:
- Put factory OTP/NVRAM into the entropy pool
- Clean up on error in mtd_otp_nvmem_add()
MTD devices changes:
- sm_ftl: Fix typos in comments
- Use SPDX license headers
- pismo: Switch back to use i2c_driver's .probe()
- mtdpart: Drop useless LIST_HEAD
- st_spi_fsm: Use the devm_clk_get_enabled() helper function
DT binding changes:
- partitions:
- Include TP-Link SafeLoader in allowed list
- Add missing type for "linux,rootfs"
- Extend the nand node names filter
- Create a file for raw NAND chip properties
- Mark nand-ecc-placement deprecated
- Describe nand-ecc-mode
- Prevent NAND chip unevaluated properties in all NAND bindings with
a NAND chip reference.
- Qcom: Fix a property position
- Marvell: Convert to YAML DT schema
Raw NAND chip drivers changes:
- Macronix: OTP access for MX30LFxG18AC
- Add basic Sandisk manufacturer ops
- Add support for Sandisk SDTNQGAMA
Raw NAND controller driver changes:
- Meson:
- Replace integer consts with proper defines
- Allow waiting w/o wired ready/busy pin
- Check buffer length validity
- Fix unaligned DMA buffers handling
- dt-bindings: Fix 'nand-rb' property
- Arasan: Revert "mtd: rawnand: arasan: Prevent an unsupported
configuration" as this limitation is no longer true thanks to the
recent efforts in improving the clocks support in this driver
SPI-NAND changes:
- Gigadevice: add support for GD5F2GQ5xExxH
- Macronix: Add support for serial NAND flashes"
* tag 'mtd/for-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (38 commits)
dt-bindings: mtd: marvell-nand: Convert to YAML DT scheme
dt-bindings: mtd: ti,am654: Prevent unevaluated properties
dt-bindings: mtd: mediatek: Prevent NAND chip unevaluated properties
dt-bindings: mtd: mediatek: Reference raw-nand-chip.yaml
dt-bindings: mtd: stm32: Prevent NAND chip unevaluated properties
dt-bindings: mtd: rockchip: Prevent NAND chip unevaluated properties
dt-bindings: mtd: intel: Prevent NAND chip unevaluated properties
dt-bindings: mtd: denali: Prevent NAND chip unevaluated properties
dt-bindings: mtd: brcmnand: Prevent NAND chip unevaluated properties
dt-bindings: mtd: meson: Prevent NAND chip unevaluated properties
dt-bindings: mtd: sunxi: Prevent NAND chip unevaluated properties
dt-bindings: mtd: ingenic: Prevent NAND chip unevaluated properties
dt-bindings: mtd: qcom: Prevent NAND chip unevaluated properties
dt-bindings: mtd: qcom: Fix a property position
dt-bindings: mtd: Describe nand-ecc-mode
dt-bindings: mtd: Mark nand-ecc-placement deprecated
dt-bindings: mtd: Create a file for raw NAND chip properties
dt-bindings: mtd: Accept nand related node names
mtd: sm_ftl: Fix typos in comments
mtd: otp: clean up on error in mtd_otp_nvmem_add()
...
|
|
Some servers may return error codes from REQ_GET_DFS_REFERRAL requests
that are unexpected by the client, so to make it easier, assume
non-DFS mounts when the client can't get the initial DFS referral of
@ctx->UNC in dfs_mount_share().
Signed-off-by: Paulo Alcantara (SUSE) <[email protected]>
Signed-off-by: Steve French <[email protected]>
|
|
When having two DFS root mounts that are connected to same namespace,
same mount options but different prefix paths, we can't really use the
shared @server->origin_fullpath when chasing DFS links in them.
Move the origin_fullpath field to cifs_tcon structure so when having
shared DFS root mounts with different prefix paths, and we need to
chase any DFS links, dfs_get_automount_devname() will pick up the
correct full path out of the @tcon that will be used for the new
mount.
Before patch
mount.cifs //dom/dfs/dir /mnt/1 -o ...
mount.cifs //dom/dfs /mnt/2 -o ...
# shared server, ses, tcon
# server: origin_fullpath=//dom/dfs/dir
# @server->origin_fullpath + '/dir/link1'
$ ls /mnt/2/dir/link1
ls: cannot open directory '/mnt/2/dir/link1': No such file or directory
After patch
mount.cifs //dom/dfs/dir /mnt/1 -o ...
mount.cifs //dom/dfs /mnt/2 -o ...
# shared server & ses
# tcon_1: origin_fullpath=//dom/dfs/dir
# tcon_2: origin_fullpath=//dom/dfs
# @tcon_2->origin_fullpath + '/dir/link1'
$ ls /mnt/2/dir/link1
dir0 dir1 dir10 dir3 dir5 dir6 dir7 dir9 target2_file.txt tsub
Fixes: 8e3554150d6c ("cifs: fix sharing of DFS connections")
Signed-off-by: Paulo Alcantara (SUSE) <[email protected]>
Signed-off-by: Steve French <[email protected]>
|