| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Check if rx offload is supported running mtk_wed_get_rx_capa routine
before configuring it. This is a preliminary patch to introduce Wireless
Ethernet Dispatcher (WED) support for MT7988 SoC.
Co-developed-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Similar to mtk_eth_soc, introduce the following wed versioning
utility routines:
- mtk_wed_is_v1
- mtk_wed_is_v2
This is a preliminary patch to introduce WED support for MT7988 SoC
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Introduce MT7988 SoC compatibility string in mtk_wed binding.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Introduce MT7988 SoC compatibility string in mt7986-wo-ccif binding.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
We have data-races while reading np->srcprefs
Switch the field to a plain byte, add READ_ONCE()
and WRITE_ONCE() annotations where needed,
and IPV6_ADDR_PREFERENCES setsockopt() can now be lockless.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20230918142321.1794107-1-edumazet@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Marek reports that a deadlock occurs with the AX88772A PHY used on the
ASIX USB network driver:
asix 1-1.4:1.0 (unnamed net_device) (uninitialized): PHY [usb-001:003:10] driver [Asix Electronics AX88772A] (irq=POLL)
Asix Electronics AX88772A usb-001:003:10: attached PHY driver(mii_bus:phy_addr=usb-001:003:10, irq=POLL)
asix 1-1.4:1.0 eth0: register 'asix' at usb-12110000.usb-1.4, ASIX AX88772 USB 2.0 Ethernet, a2:99:b6:cd:11:eb
asix 1-1.4:1.0 eth0: configuring for phy/internal link mode
============================================
WARNING: possible recursive locking detected
6.6.0-rc1-00239-g8da77df649c4-dirty #13949 Not tainted
--------------------------------------------
kworker/3:3/71 is trying to acquire lock:
c6c704cc (&dev->lock){+.+.}-{3:3}, at: phy_start_aneg+0x1c/0x38
but task is already holding lock:
c6c704cc (&dev->lock){+.+.}-{3:3}, at: phy_state_machine+0x100/0x2b8
This is because we now consistently call phy_process_state_change()
while holding phydev->lock, but the AX88772A PHY driver then goes on
to call phy_start_aneg() which tries to grab the same lock - causing
deadlock.
Fix this by exporting the unlocked version, and use this in the PHY
driver instead.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: ef113a60d0a9 ("net: phy: call phy_error_precise() while holding the lock")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/E1qiEFs-007g7b-Lq@rmk-PC.armlinux.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
There is a spelling mistake in a dev_err message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20230918132142.199638-1-colin.i.king@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Separated queue specific interrupts to register to individual msix-vectors
instead of using a single generic interrupt handler on a single
msix-vector.
Signed-off-by: Shinas Rasheed <srasheed@marvell.com>
Link: https://lore.kernel.org/r/20230918065621.2165449-1-srasheed@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Jisheng Zhang says:
====================
stmmac: convert to devm_stmmac_probe_config_dt
Russell pointed out there's a new devm_stmmac_probe_config_dt()
helper now when reviewing my starfive gmac error handling patch[1].
After greping the code, this nice helper was introduced by Bartosz in
[2], I think it's time to convert all dwmac users to this helper and
finally complete the TODO in [2] "but once all users of the old
stmmac_pltfr_remove() are converted to the devres helper, it will be
renamed back to stmmac_pltfr_remove() and the no_dt function removed."
Link: https://lore.kernel.org/netdev/ZOtWmedBsa6wQQ6+@shell.armlinux.org.uk/ [1]
Link: https://lore.kernel.org/all/20230623100417.93592-1-brgl@bgdev.pl/ [2]
Since v1:
- rebase on new net-next
- add make stmmac_{probe|remove}_config_dt static as suggested by Russell.
====================
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now there's no external users of these two functions, make them static
so that there aren't any new usages of stmmac_probe_config_dt().
To avoid forward declaration, move stmmac_remove_config_dt() location.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Suggested-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now, all users of the old stmmac_pltfr_remove() are converted to the
devres helper, it's time to rename stmmac_pltfr_remove_no_dt() back to
stmmac_pltfr_remove() and remove the old stmmac_pltfr_remove().
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the driver's probe() function by using the devres
variant of stmmac_probe_config_dt().
The calling of stmmac_pltfr_remove() now needs to be switched to
stmmac_pltfr_remove_no_dt().
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the driver's probe() function by using the devres
variant of stmmac_probe_config_dt().
The calling of stmmac_pltfr_remove() now needs to be switched to
stmmac_pltfr_remove_no_dt().
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the driver's probe() function by using the devres
variant of stmmac_probe_config_dt().
The remove_new() callback now needs to be switched to
stmmac_pltfr_remove_no_dt().
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the driver's probe() function by using the devres
variant of stmmac_probe_config_dt().
The calling of stmmac_pltfr_remove() now needs to be switched to
stmmac_pltfr_remove_no_dt().
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the driver's probe() function by using the devres
variant of stmmac_probe_config_dt().
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the driver's probe() function by using the devres
variant of stmmac_probe_config_dt().
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the driver's probe() function by using the devres
variant of stmmac_probe_config_dt().
The remove_new() callback now needs to be switched to
stmmac_pltfr_remove_no_dt().
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the driver's probe() function by using the devres
variant of stmmac_probe_config_dt().
The calling of stmmac_pltfr_remove() now needs to be switched to
stmmac_pltfr_remove_no_dt().
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the driver's probe() function by using the devres
variant of stmmac_probe_config_dt().
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the driver's probe() function by using the devres
variant of stmmac_probe_config_dt().
The remove_new() callback now needs to be switched to
stmmac_pltfr_remove_no_dt().
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the driver's probe() function by using the devres
variant of stmmac_probe_config_dt().
The remove_new() callback now needs to be switched to
stmmac_pltfr_remove_no_dt().
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the driver's probe() function by using the devres
variant of stmmac_probe_config_dt().
The calling of stmmac_pltfr_remove() now needs to be switched to
stmmac_pltfr_remove_no_dt().
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the driver's probe() function by using the devres
variant of stmmac_probe_config_dt().
The remove_new() callback now needs to be switched to
stmmac_pltfr_remove_no_dt().
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the driver's probe() function by using the devres
variant of stmmac_probe_config_dt().
The remove_new() callback now needs to be switched to
stmmac_pltfr_remove_no_dt().
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the driver's probe() function by using the devres
variant of stmmac_probe_config_dt().
The calling of stmmac_pltfr_remove() now needs to be switched to
stmmac_pltfr_remove_no_dt().
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the driver's probe() function by using the devres
variant of stmmac_probe_config_dt().
The remove_new() callback now needs to be switched to
stmmac_pltfr_remove_no_dt().
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the driver's probe() function by using the devres
variant of stmmac_probe_config_dt().
The remove_new() callback now needs to be switched to
stmmac_pltfr_remove_no_dt().
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the devres variant of stmmac_pltfr_probe() and finally drop the
remove() hook.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the driver's probe() function by using the devres
variant of stmmac_probe_config_dt().
The remove_new() callback now needs to be switched to
stmmac_pltfr_remove_no_dt().
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the driver's probe() function by using the devres
variant of stmmac_probe_config_dt().
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the driver's probe() function by using the devres
variant of stmmac_probe_config_dt().
The remove_new() callback now needs to be switched to
stmmac_pltfr_remove_no_dt().
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rohan G Thomas says:
====================
net: stmmac: Tx coe sw fallback
DW xGMAC IP can be synthesized such that it can support tx checksum
offloading only for a few initial tx queues. Also as Serge pointed
out, for the DW QoS IP, tx coe can be individually configured for
each tx queue. This patchset adds support for tx coe sw fallback for
those queues that don't support tx coe. Also, add binding for
snps,coe-unsupported property.
changelog v7:
* Updated commit message.
* Add blank lines around newly added dt binding.
changelog v6:
* Reworked patchset to cover DW QoS Ethernet IP also.
changelog v5:
* As rightly suggested by Serge, reworked redundant code.
changelog v4:
* Replaced tx_q_coe_lmt with bit flag.
changelog v3:
* Resend with complete email list.
changelog v2:
* Reformed binding description.
* Minor grammatical corrections in comments and commit messages.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add sw fallback of tx checksum calculation for those tx queues that
don't support tx checksum offloading. DW xGMAC IP can be synthesized
such that it can support tx checksum offloading only for a few
initial tx queues. Also as Serge pointed out, for the DW QoS IP, tx
coe can be individually configured for each tx queue.
So when tx coe is enabled, for any tx queue that doesn't support
tx coe with 'coe-unsupported' flag set will have a sw fallback
happen in the driver for tx checksum calculation when any packets to
be transmitted on these tx queues.
Signed-off-by: Rohan G Thomas <rohan.g.thomas@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add dt-bindings for coe-unsupported property per tx queue. Some DWMAC
IPs support tx checksum offloading(coe) only for a few tx queues.
DW xGMAC IP can be synthesized such that it can support tx coe only
for a few initial tx queues. Also as Serge pointed out, for the DW
QoS IP tx coe can be individually configured for each tx queue. This
property is added to have sw fallback for checksum calculation if a
tx queue doesn't support tx coe.
Signed-off-by: Rohan G Thomas <rohan.g.thomas@intel.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct ceph_monmap.
Additionally, since the element count member must be set before accessing
the annotated flexible array member, move its initialization earlier.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Ilya Dryomov <idryomov@gmail.com>
Cc: Xiubo Li <xiubli@redhat.com>
Cc: Jeff Layton <jlayton@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: ceph-devel@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Xiubo Li <xiubli@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If, for any reason, the open-coded arithmetic causes a wraparound,
the protection that `struct_size()` adds against potential integer
overflows is defeated. Fix this by hardening call to `struct_size()`
with `size_add()`.
Fixes: 3f1071ec39f7 ("net: spider_net: Use struct_size() helper")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If, for any reason, the open-coded arithmetic causes a wraparound,
the protection that `struct_size()` adds against potential integer
overflows is defeated. Fix this by hardening call to `struct_size()`
with `size_add()`.
Fixes: e034c6d23bc4 ("tipc: Use struct_size() helper")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If, for any reason, the open-coded arithmetic causes a wraparound,
the protection that `struct_size()` adds against potential integer
overflows is defeated. Fix this by hardening call to `struct_size()`
with `size_add()`.
Fixes: b89fec54fd61 ("tls: rx: wrap decrypt params in a struct")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If, for any reason, the open-coded arithmetic causes a wraparound, the
protection that `struct_size()` adds against potential integer overflows
is defeated. Fix this by hardening call to `struct_size()` with `size_mul()`.
Fixes: 2285ec872d9d ("mlxsw: spectrum_acl_bloom_filter: use struct_size() in kzalloc()")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Daniel Mendes says:
====================
kselftest: rtnetlink: add additional command line options
Many other tests implement options like verbose, pause, and pause
on failure. These patches just add these options to rtnetlink.sh.
The same conventions are used as the tests that already have this
functionality: eg verbose is 0 or 1 but PAUSE is "yes" or "no".
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
'Pause' prompts the user to press Enter to continue running tests
once one test has finished. Pause on fail on prompts the user to press
enter only when a test fails.
Modifications to kci_test_addrlft() and kci_test_ipsec_offload()
ensure that whenever end_test is called, [$ret -ne 0] indicates
failure. This allows end_test to really easily implement pause on fail
functionality.
Signed-off-by: Daniel Mendes <dmendes@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Uses a run_cmd helper function similar to other selftests to add
verbose functionality i.e. print executed commands and their outputs
Many commands silence or redirect output. This can be removed since
the verbose helper function captures output anyway and only outputs it
if VERBOSE is true. Similarly, the helper command for pipes to grep
searches stderr and stdout. This makes output redirection unnecessary
in those cases.
Signed-off-by: Daniel Mendes <dmendes@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Shannon Nelson says:
====================
pds_core: add PCI reset handling
Make sure pds_core can handle and recover from PCI function resets and
similar PCI bus issues: add detection and handlers for PCI problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we see a 0xff value from a PCI register read, we know that
the PCI connection is broken, possibly by a low level reset that
didn't go through the nice pci_error_handlers path.
Make use of the PCI cleanup code that we already have from the
reset handlers and add some detection and attempted recovery
from a broken PCI connection.
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement the callbacks for a nice PCI reset. These get called
when a user is nice enough to use the sysfs PCI reset entry, e.g.
echo 1 > /sys/bus/pci/devices/0000:2b:00.0/reset
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Keep the viftypes and the current enable/disable states
across a recovery action.
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similar to what we do in the AdminQ, check for devcmd health
while waiting for an answer.
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support to fetch firmware info such as heartbeat miss count,
heartbeat interval. This shall be used for heartbeat monitor.
Signed-off-by: Shinas Rasheed <srasheed@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If, for any reason, `tx_stats_num + rx_stats_num` wraps around, the
protection that struct_size() adds against potential integer overflows
is defeated. Fix this by hardening call to struct_size() with size_add().
Fixes: 691f4077d560 ("gve: Replace zero-length array with flexible-array member")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|