| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The PCIe QMP 4x2 RC PHY generates high latency when ASPM is enabled. This
seem to be fixed by clearing the QPHY_V5_20_PCS_PCIE_PRESET_P10_POST
register of the pcs_misc register space.
Fixes: 2c91bf6bf290 ("phy: qcom-qmp: Add SM8450 PCIe1 PHY support")
Signed-off-by: Manivannan Sadhasivam <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
Commit af6643242d3a ("phy: qcom-qmp-pcie: split pcs_misc region for ipq6018
pcie gen3") reworked the pcs regs values and removed the 0x400 offset
for each pcs_misc regs.
This change caused the malfunction of ipq8074 downstream since it still
has the legacy pcs table where pcs_misc are not placed on a different
table and instead put together assuming the offset of 0x400 for the
related pcs_misc regs.
Split pcs_misc init cfg from the ipq8074 pcs init table to be handled
correctly to prepare for actual support for gen3 pcie for ipq8074.
Fixes: af6643242d3a ("phy: qcom-qmp-pcie: split pcs_misc region for ipq6018 pcie gen3")
Reported-by: Robert Marko <[email protected]>
Tested-by: Robert Marko <[email protected]>
Signed-off-by: Christian Marangi <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
The PCIe2 and PCIe3 controllers and PHYs on SC8280XP can be used in
4-lane mode or as separate controllers and PHYs in 2-lane mode (e.g. as
PCIe2A and PCIe2B).
Add support for fetching the 4-lane configuration from the TCSR and
programming the lane registers of the second port when in 4-lane mode.
Reviewed-by: Dmitry Baryshkov <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
Add support for the single and dual-lane PHYs found on SC8280XP.
Note that the SC8280XP binding does not try to describe every register
subregion and instead the driver holds the corresponding offsets.
Reviewed-by: Dmitry Baryshkov <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
Some QMP PHYs have a second fixed-divider pipe clock that needs to be
enabled along with the pipe clock.
Add support for an optional "pipediv2" clock.
Reviewed-by: Dmitry Baryshkov <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
Add the missing delay after asserting reset. This is specifically needed
for the reset to have any effect on SC8280XP.
The vendor driver uses a 1 ms delay, but that seems a bit excessive.
Instead use a 200 us delay which appears to be more than enough and also
matches the UFS reset delay added by commit 870b1279c7a0 ("scsi:
ufs-qcom: Add reset control support for host controller").
Reviewed-by: Dmitry Baryshkov <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
In preparation for supporting devicetree bindings which do not use a
child node, move the PHY creation to probe() proper and parse the serdes
resource in what is now the legacy devicetree helper.
Reviewed-by: Dmitry Baryshkov <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
Add bindings for the PCIe QMP PHYs found on SC8280XP.
The PCIe2 and PCIe3 controllers and PHYs on SC8280XP can be used in
4-lane mode or as separate controllers and PHYs in 2-lane mode (e.g. as
PCIe2A and PCIe2B).
The configuration for a specific system can be read from a TCSR register.
Reviewed-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
The current QMP PCIe PHY bindings are based on the original MSM8996
binding which provided multiple PHYs per IP block and these in turn were
described by child nodes.
Later QMP PCIe PHY blocks only provide a single PHY and the remnant
child node does not really reflect the hardware.
The original MSM8996 binding also ended up describing the individual
register blocks as belonging to either the wrapper node or the PHY child
nodes.
This is an unnecessary level of detail which has lead to problems when
later IP blocks using different register layouts have been forced to fit
the original mould rather than updating the binding. The bindings are
arguable also incomplete as they only the describe register blocks used
by the current Linux drivers (e.g. does not include the per lane PCS
registers).
In preparation for adding new bindings for SC8280XP which further
bindings can be based on, rename the current schema file after IPQ8074,
which was the first SoC added to the bindings after MSM8996 (which has
already been split out), and add a reference to the SC8280XP bindings.
Reviewed-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
Generalise the serdes initialisation helper so that it can be used to
initialise all the PHY registers (e.g. serdes, tx, rx, pcs).
Note that this defers the ungating of the PIPE clock somewhat, which is
fine as it isn't needed until starting the PHY.
Reviewed-by: Dmitry Baryshkov <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
The QMP drivers all use 'tbl' to refer to their register initialisation
tables.
For consistency use 'tbls' rather than 'tables' to refer to the new
aggregate table structures.
Signed-off-by: Johan Hovold <[email protected]>
Reviewed-by: Dmitry Baryshkov <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
Clean up the PHY lane initialisation somewhat by adding further
temporary variables and programming both tx and rx for the second lane
after the first lane.
Reviewed-by: Dmitry Baryshkov <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
Rename the PHY operation structure so that it has a "phy_ops" suffix and
move it next to the implementation.
Reviewed-by: Dmitry Baryshkov <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
Stop abusing the driver data pointer and instead pass the driver state
structure directly to the initialisation helpers during probe.
Reviewed-by: Dmitry Baryshkov <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
Since the QMP driver split there will be at most a single child node so
drop the obsolete iteration construct.
While at it, drop the verbose error logging that would have been
printed also on probe deferrals.
Note that there's no need to check if there are additional child nodes
(the kernel is not a devicetree validator), but let's return an error if
there are no child nodes at all for now.
Reviewed-by: Dmitry Baryshkov <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
The PCIe QMP PHY driver only manages a single PHY so merge the old
qcom_qmp and qmp_phy structures and drop the PHY array.
Reviewed-by: Dmitry Baryshkov <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
Move the device-id table below probe() and next to the driver structure
to keep the driver callback functions grouped together.
Reviewed-by: Dmitry Baryshkov <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
Sort the device-id table by compatible string to make it easier to find
and add new entries.
Reviewed-by: Dmitry Baryshkov <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
Document the typical order of API calls to used by new drivers and
controllers. Many existing controllers follow this order, but some do
not. This is especially true for controllers designed to work with one
particular PHY driver, which may not need a call to (for example)
phy_init.
Signed-off-by: Sean Anderson <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
Remove redundant codes for getting the vbus supply of usb3 ports because
we get and control the vbus supply by the companion usb2 ports
Signed-off-by: Wayne Chang <[email protected]>
Signed-off-by: Haotien Hsu <[email protected]>
Reviewed-by: Jon Hunter <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
The wake-up interrupt lines are entirely optional, avoid printing
messages that interrupts were not found by switching to the _optional
variant.
Signed-off-by: Florian Fainelli <[email protected]>
Acked-by: Justin Chen <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
Each of the CPSW9G ports in J721e support additional modes like QSGMII.
Add a new compatible for J721e to support the additional modes.
In TI's J721e, each of the CPSW9G ethernet interfaces can act as a
QSGMII main or QSGMII-SUB port. The QSGMII main interface is responsible
for performing auto-negotiation between the MAC and the PHY while the rest
of the interfaces are designated as QSGMII-SUB interfaces, indicating that
they will not be taking part in the auto-negotiation process.
Signed-off-by: Siddharth Vadapalli <[email protected]>
Reviewed-by: Roger Quadros <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
The number of QSGMII main ports are specific to the device. TI's J7200 for
which the QSGMII main port property is fetched from the device-tree has
only one QSGMII main port. However, devices like TI's J721e support up to
two QSGMII main ports. Thus, the existing methods for fetching and using
the QSGMII main port are not scalable.
Update the existing methods for handling the QSGMII main ports and its
associated requirements to make it scalable for future devices.
Signed-off-by: Siddharth Vadapalli <[email protected]>
Reviewed-by: Roger Quadros <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
TI's J721e SoC supports additional PHY modes like QSGMII and SGMII
that are not supported on earlier SoCs. Add a compatible for it.
Extend ti,qsgmii-main-ports property to support selection of upto
two main ports at once across the two QSGMII interfaces.
Signed-off-by: Siddharth Vadapalli <[email protected]>
Reviewed-by: Rob Herring <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
The USB PHY used in the Allwinner H616 SoC inherits some traits from its
various predecessors: it has four full PHYs like the H3, needs some
extra bits to be set like the H6, and puts SIDDQ on a different bit like
the A100. Plus it needs this weird PHY2 quirk.
Name all those properties in a new config struct and assign a new
compatible name to it.
Signed-off-by: Andre Przywara <[email protected]>
Reviewed-by: Samuel Holland <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
At least the Allwinner H616 SoC requires a weird quirk to make most
USB PHYs work: Only port2 works out of the box, but all other ports
need some help from this port2 to work correctly: The CLK_BUS_PHY2 and
RST_USB_PHY2 clock and reset need to be enabled, and the SIDDQ bit in
the PMU PHY control register needs to be cleared. For this register to
be accessible, CLK_BUS_ECHI2 needs to be ungated. Don't ask ....
Instead of disguising this as some generic feature, treat it more like
a quirk (what it really is):
If the quirk bit is set, and we initialise a PHY other than PHY2, ungate
this one special clock, and clear the SIDDQ bit. We also pick the clock
and reset from PHY2 and enable them as well.
Signed-off-by: Andre Przywara <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
The USB PHY IP in the Allwinner H616 SoC requires a quirk that involves
some resources from port 2's PHY and HCI IP. In particular the PMU clock
for port 2 must be surely ungated before accessing the REG_HCI_PHY_CTL
register of port 2. To allow each USB port to be controlled
independently of port 2, we need a handle to that particular PMU clock
in the *PHY* node, as the HCI and PHY part might be handled by separate
drivers.
Add that clock to the requirements of the H616 PHY binding, so that a
PHY driver can apply the quirk in isolation, without requiring help from
port 2's HCI driver.
Signed-off-by: Andre Przywara <[email protected]>
Reviewed-by: Rob Herring <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
We should be disabling clocks when wake from USB is not needed. Since
this wasn't done, we had a clock imbalance since clocks were always
being enabled on resume.
Fixes: ae532b2b7aa5 ("phy: usb: Add "wake on" functionality for newer Synopsis XHCI controllers")
Fixes: b0c0b66c0b43 ("phy: usb: Add support for wake and USB low power mode for 7211 S2/S5")
Signed-off-by: Justin Chen <[email protected]>
Acked-by: Florian Fainelli <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
The logic was incorrect when switching to slow clock. We want the slow
clock if wake_enabled is set.
Fixes: ae532b2b7aa5 ("phy: usb: Add "wake on" functionality for newer Synopsis XHCI controllers")
Signed-off-by: Justin Chen <[email protected]>
Acked-by: Florian Fainelli <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
The BDC block requires the PLL lock in order to grab the PLL clock.
The phy auto-suspend feature turns off the phy when nothing is attached
leading to the PLL to not lock. This leads the BDC block to grab the AUX
clock instead of the PLL clock. This is not ideal, so lets turn this
feature off.
Signed-off-by: Justin Chen <[email protected]>
Acked-by: Florian Fainelli <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
Using BIT and BITMASK macros makes it much easier to read and make
modifications. Also reordered some constants to be in numerical order.
Signed-off-by: Justin Chen <[email protected]>
Acked-by: Florian Fainelli <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
The PHY's "wakeup_count" is not incrementing when waking from
WoL. The wakeup count can be found in sysfs at:
/sys/bus/platform/devices/rdb/*.usb-phy/power/wakeup_count.
The problem is that the system wakup event handler was being passed
the wrong "device" by the PHY driver.
Fixes: f1c0db40a3ad ("phy: usb: Add "wake on" functionality")
Signed-off-by: Al Cooper <[email protected]>
Signed-off-by: Justin Chen <[email protected]>
Acked-by: Florian Fainelli <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
Split port modes into two different variables. Supported port modes
is what the hardware supports. While port mode is how the hardware
is currently configured and can be dynamically changed through the
sysfs. We initialize all supported port modes on init even though
the port mode may not be selected because we cannot guarantee the
downstream interface from the phy will be active or not.
This also fixes an issue where port modes selected via sysfs were
not being saved through suspend/resume.
Signed-off-by: Justin Chen <[email protected]>
Acked-by: Florian Fainelli <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
Add support for the new SC8280XP binding.
Note that the binding does not try to describe every register subregion
and instead the driver holds the corresponding offsets. This includes
the PCS_USB region which was initially overlooked.
Note that the driver will no longer accept the old binding due to the
fixed "phy_phy" reset name.
Reviewed-by: Dmitry Baryshkov <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
In preparation for supporting devicetree bindings which do not use a
child node, move the PHY creation to probe() proper and parse the serdes
and dp_com resources in what is now the legacy devicetree helper.
Reviewed-by: Dmitry Baryshkov <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
The current QMP USB PHY bindings are based on the original MSM8996 PCIe
PHY binding which provided multiple PHYs per IP block and these in turn
were described by child nodes.
The QMP USB PHY block only provide a single PHY and the remnant child
node does not really reflect the hardware.
The original MSM8996 binding also ended up describing the individual
register blocks as belonging to either the wrapper node or the PHY child
nodes.
This is an unnecessary level of detail which has lead to problems when
later IP blocks using different register layouts have been forced to fit
the original mould rather than updating the binding. The bindings are
arguable also incomplete as they only the describe register blocks used
by the current Linux drivers (e.g. does not include the per lane PCS
registers).
Note that PCS_USB region is also not described by the current bindings
despite being used by the driver and this has led to people increasing
the size of the PCS region in the devicetree so that it includes PCS_USB
registers even though other regions like TX and RX may lie in between.
Add a new binding for the QMP USB PHYs found on SC8280XP which further
bindings can be based on.
Note that this also fixes the SC8280XP "phy_phy" reset name.
Also note that the current binding is simply removed instead of being
deprecated as it was only recently merged and support for SC8280XP is
still under development. And, specifically, there is no support in
mainline for the multiport controller that uses these PHYs.
Signed-off-by: Johan Hovold <[email protected]>
Reviewed-by: Rob Herring <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
The current QMP USB PHY bindings are based on the original MSM8996
binding which provided multiple PHYs per IP block and these in turn were
described by child nodes.
Later QMP USB PHY blocks only provide a single PHY and the remnant child
node does not really reflect the hardware.
The original MSM8996 binding also ended up describing the individual
register blocks as belonging to either the wrapper node or the PHY child
nodes.
This is an unnecessary level of detail which has lead to problems when
later IP blocks using different register layouts have been forced to fit
the original mould rather than updating the binding. The bindings are
arguable also incomplete as they only the describe register blocks used
by the current Linux drivers (e.g. does not include the per lane PCS
registers).
In preparation for adding new bindings for SC8280XP which further
bindings can be based on, rename the current bindings after MSM8996 and
add a reference to the SC8280XP bindings.
Reviewed-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
Clean up the PHY initialisation somewhat by programming both tx and rx
for the second lane after the first lane.
Reviewed-by: Dmitry Baryshkov <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
Rename the PHY operation structure so that it has a "phy_ops" suffix and
move it next to the implementation.
Reviewed-by: Dmitry Baryshkov <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
Stop abusing the driver data pointer and instead pass the driver state
structure directly to the initialisation helpers during probe.
Reviewed-by: Dmitry Baryshkov <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
Since the QMP driver split there will be at most a single child node so
drop the obsolete iteration construct.
While at it, drop the verbose error logging that would have been
printed also on probe deferrals.
Note that there's no need to check if there are additional child nodes
(the kernel is not a devicetree validator), but let's return an error if
there are no child nodes at all for now.
Reviewed-by: Dmitry Baryshkov <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
The USB QMP PHY driver only manages a single PHY so merge the old
qcom_qmp and qmp_phy structures and drop the PHY array.
Reviewed-by: Dmitry Baryshkov <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
Move the PM ops structure next to the implementation to keep the driver
callbacks grouped.
Reviewed-by: Dmitry Baryshkov <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
Move the device-id table below probe() and next to the driver structure
to keep the driver callback functions grouped together.
Reviewed-by: Dmitry Baryshkov <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
Sort the device-id table by compatible string to make it easier to find
and add new entries.
Reviewed-by: Dmitry Baryshkov <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
The PCS_USB register block lives at an offset of 0x1000 from the PCS
region on SC8280XP so add the missing offset to avoid corrupting
unrelated registers on runtime suspend.
Note that the current binding is broken as it does not describe the
PCS_USB region and the PCS register size does not cover PCS_USB and the
regions in between. As Linux currently maps full pages, simply adding
the offset to driver works until the binding has been fixed.
Fixes: c0c7769cdae2 ("phy: qcom-qmp: Add SC8280XP USB3 UNI phy")
Reviewed-by: Dmitry Baryshkov <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
Merge the fixes to next as both carry qmp-phy patches
|
|
Add support for the new SC8280XP binding.
Note that the binding does not try to describe every register subregion
and instead the driver holds the corresponding offsets.
Also note that the driver will continue to accept the old binding, at
least for the time being.
Signed-off-by: Johan Hovold <[email protected]>
Reviewed-by: Dmitry Baryshkov <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
In preparation for supporting devicetree bindings which do not use a
child node, move the PHY creation to probe() proper and parse the serdes
resource in what is now the legacy devicetree helper.
Signed-off-by: Johan Hovold <[email protected]>
Reviewed-by: Dmitry Baryshkov <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
The current QMP UFS PHY bindings are based on the original MSM8996 PCIe
PHY binding which provided multiple PHYs per IP block and these in turn
were described by child nodes.
The QMP UFS PHY block only provide a single PHY and the remnant child
node does not really reflect the hardware.
The original MSM8996 binding also ended up describing the individual
register blocks as belonging to either the wrapper node or the PHY child
nodes.
This is an unnecessary level of detail which has lead to problems when
later IP blocks using different register layouts have been forced to fit
the original mould rather than updating the binding. The bindings are
arguable also incomplete as they only the describe register blocks used
by the current Linux drivers.
Add a new binding for the UFS QMP PHYs found on SC8280XP which further
bindings can be based on.
Note that the current binding is simply removed instead of being
deprecated as it was only recently merged and support for SC8280XP is
still under development.
Signed-off-by: Johan Hovold <[email protected]>
Reviewed-by: Krzysztof Kozlowski <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|