aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2017-10-04mmc: meson-gx: fix rx phase resetJerome Brunet1-2/+4
Resetting the phase when POWER_ON is set the set_ios() call means that the phase is reset almost every time the set_ios() is called, while the expected behavior was to reset the phase on a power cycle. This had gone unnoticed until now because in all mode (except hs400) the tuning is done after the last to set_ios(). In such case, the tuning result is used anyway. In HS400, there are a few calls to set_ios() after the tuning is done, overwriting the tuning result. Resetting the phase on POWER_UP instead of POWER_ON solve the problem. Fixes: d341ca88eead ("mmc: meson-gx: rework tuning function") Signed-off-by: Jerome Brunet <[email protected]> Reviewed-by: Kevin Hilman <[email protected]> Signed-off-by: Ulf Hansson <[email protected]>
2017-10-04mmc: meson-gx: make sure the clock is rounded downJerome Brunet1-2/+1
Using CLK_DIVIDER_ROUND_CLOSEST is unsafe as the mmc clock could be rounded to a rate higher the specified rate. Removing this flag ensure that, if the rate needs to be rounded, it will be rounded down. Fixes: 51c5d8447bd7 ("MMC: meson: initial support for GX platforms") Signed-off-by: Jerome Brunet <[email protected]> Reviewed-by: Kevin Hilman <[email protected]> Signed-off-by: Ulf Hansson <[email protected]>
2017-10-04mmc: Delete bounce buffer handlingLinus Walleij6-132/+12
In may, Steven sent a patch deleting the bounce buffer handling and the CONFIG_MMC_BLOCK_BOUNCE option. I chose the less invasive path of making it a runtime config option, and we merged that successfully for kernel v4.12. The code is however just standing in the way and taking up space for seemingly no gain on any systems in wide use today. Pierre says the code was there to improve speed on TI SDHCI controllers on certain HP laptops and possibly some Ricoh controllers as well. Early SDHCI controllers lacked the scatter-gather feature, which made software bounce buffers a significant speed boost. We are clearly talking about the list of SDHCI PCI-based MMC/SD card readers found in the pci_ids[] list in drivers/mmc/host/sdhci-pci-core.c. The TI SDHCI derivative is not supported by the upstream kernel. This leaves the Ricoh. What we can however notice is that the x86 defconfigs in the kernel did not enable CONFIG_MMC_BLOCK_BOUNCE option, which means that any such laptop would have to have a custom configured kernel to actually take advantage of this bounce buffer speed-up. It simply seems like there was a speed optimization for the Ricoh controllers that noone was using. (I have not checked the distro defconfigs but I am pretty sure the situation is the same there.) Bounce buffers increased performance on the OMAP HSMMC at one point, and was part of the original submission in commit a45c6cb81647 ("[ARM] 5369/1: omap mmc: Add new omap hsmmc controller for 2430 and 34xx, v3") This optimization was removed in commit 0ccd76d4c236 ("omap_hsmmc: Implement scatter-gather emulation") which found that scatter-gather emulation provided even better performance. The same was introduced for SDHCI in commit 2134a922c6e7 ("sdhci: scatter-gather (ADMA) support") I am pretty positively convinced that software scatter-gather emulation will do for any host controller what the bounce buffers were doing. Essentially, the bounce buffer was a reimplementation of software scatter-gather-emulation in the MMC subsystem, and it should be done away with. Cc: Pierre Ossman <[email protected]> Cc: Juha Yrjola <[email protected]> Cc: Steven J. Hill <[email protected]> Cc: Shawn Lin <[email protected]> Cc: Adrian Hunter <[email protected]> Suggested-by: Steven J. Hill <[email protected]> Suggested-by: Shawn Lin <[email protected]> Signed-off-by: Linus Walleij <[email protected]> Signed-off-by: Ulf Hansson <[email protected]>
2017-10-04dt-bindings: serial: document rs485 bindings for various devicesUwe Kleine-König4-0/+4
Atmel USART, Freescale UARTs and OMAP UART all support the rs485 binding described in rs485.txt, this commit just makes that explicit. Acked-by: Nicolas Ferre <[email protected]> Acked-by: Rob Herring <[email protected]> Signed-off-by: Uwe Kleine-König <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2017-10-04serial: 8250_dw: Improve clock rate settingEd Blake1-12/+18
Currently dw8250_set_termios sets the input clock to the nearest achievable rate to baudx16. If necessary, the input clock is then divided down to baudx16 using an integer divider within the UART device, with the divisor calculated in the 8250 core driver. However, the clock rate set by dw8250_set_termios and subsequently divided down could be considerably different to the target baudx16 rate, resulting in incorrect operation. This patch fixes this by iteratively searching for an input clock rate that is within +/-1.6% of an integer multiple of the target baudx16 rate. Signed-off-by: Ed Blake <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2017-10-04serial: Add define for max baud rate divisorEd Blake4-4/+5
Add a define for the maximum baud rate divisor, to improve code readability. Signed-off-by: Ed Blake <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2017-10-04serial: sh-sci: suppress warning for ports without dma channelsAndy Lowe1-0/+8
If a port has no dma channel defined in the device tree, then don't attempt to allocate a dma channel for the port. Also suppress the warning message concerning the failure to allocate a dma channel. Continue to emit the warning message if a dma channel is defined but cannot be allocated. Signed-off-by: Andy Lowe <[email protected]> Signed-off-by: Eugeniu Rosca <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2017-10-04serial: 8250_mid: Enable HSU on Intel Cedar Fork PCHAndy Shevchenko2-2/+5
Intel Cedar Fork PCH has similar HSU as has been used on Intel Denverton. Add PCI ID to get it enumerated. While here, remove DNV part form INTEL_MID_UART_DNV_FISR to show that is used not only on Intel Denverton from now on. Signed-off-by: Andy Shevchenko <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2017-10-04mxser: remove unused parametersJiri Slaby1-9/+7
Remove * pdev from mxser_initbrd * old_termios from mxser_change_speed as they are unused and update the callers. Signed-off-by: Jiri Slaby <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2017-10-04tty: xilinx_uartps: move to arch_initcall for earlier consoleShubhrajyoti Datta1-1/+1
move to arch_initcall to get the console up really early, it is quite helpful for spotting early boot problems. Signed-off-by: Shubhrajyoti Datta <[email protected]> Tested-by: Michal Simek <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2017-10-04Arm: dts: stm32: remove extra compatible string from DT & driverVikas Manocha4-17/+14
This patch remove the extra compatibility string "st,stm32-usart" from driver & device tree. Signed-off-by: Vikas Manocha <[email protected]> Reviewed-by: Patrice Chotard <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2017-10-04Arm: dts: stm32: remove extra compatible string for uartVikas Manocha2-8/+4
This patch removes the extra compatibility string "st,stm32-usart" to avoid confusion, save some time & space. Signed-off-by: Vikas Manocha <[email protected]> Reviewed-by: Patrice Chotard <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2017-10-04tty/serial: atmel: Prevent a warning on suspendRomain Izard1-0/+13
The atmel serial port driver reported the following warning on suspend: atmel_usart f8020000.serial: ttyS1: Unable to drain transmitter As the ATMEL_US_TXEMPTY status bit in ATMEL_US_CSR is always cleared when the transmitter is disabled, we need to know the transmitter's state to return the real fifo state. And as ATMEL_US_CR is write-only, it is necessary to save the state of the transmitter in a local variable, and update the variable when TXEN and TXDIS is written in ATMEL_US_CR. After those changes, atmel_tx_empty can return "empty" on suspend, the warning in uart_suspend_port disappears, and suspending is 20ms shorter for each enabled Atmel serial port. Signed-off-by: Romain Izard <[email protected]> Tested-by: Nicolas Ferre <[email protected]> Acked-by: Nicolas Ferre <[email protected]> Acked-by: Richard Genoud <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2017-10-04lsm: fix smack_inode_removexattr and xattr_getsecurity memleakCasey Schaufler2-31/+26
security_inode_getsecurity() provides the text string value of a security attribute. It does not provide a "secctx". The code in xattr_getsecurity() that calls security_inode_getsecurity() and then calls security_release_secctx() happened to work because SElinux and Smack treat the attribute and the secctx the same way. It fails for cap_inode_getsecurity(), because that module has no secctx that ever needs releasing. It turns out that Smack is the one that's doing things wrong by not allocating memory when instructed to do so by the "alloc" parameter. The fix is simple enough. Change the security_release_secctx() to kfree() because it isn't a secctx being returned by security_inode_getsecurity(). Change Smack to allocate the string when told to do so. Note: this also fixes memory leaks for LSMs which implement inode_getsecurity but not release_secctx, such as capabilities. Signed-off-by: Casey Schaufler <[email protected]> Reported-by: Konstantin Khlebnikov <[email protected]> Cc: [email protected] Signed-off-by: James Morris <[email protected]>
2017-10-03 xfs: handle racy AIO in xfs_reflink_end_cowChristoph Hellwig1-1/+8
If we got two AIO writes into a COW area the second one might not have any COW extents left to convert. Handle that case gracefully instead of triggering an assert or accessing beyond the bounds of the extent list. Signed-off-by: Christoph Hellwig <[email protected]> Reviewed-by: Darrick J. Wong <[email protected]> Signed-off-by: Darrick J. Wong <[email protected]>
2017-10-03xfs: always swap the cow forks when swapping extentsDarrick J. Wong1-2/+22
Since the CoW fork exists as a secondary data structure to the data fork, we must always swap cow forks during swapext. We also need to swap the extent counts and reset the cowblocks tags. Reviewed-by: Brian Foster <[email protected]> Reviewed-by: Christoph Hellwig <[email protected]> Signed-off-by: Darrick J. Wong <[email protected]>
2017-10-03ARC: [plat-hsdk]: Temporary fix to set CPU frequency to 1GHzEugeniy Paltsev1-0/+42
Add temporary fix to HSDK platform code to setup CPU frequency to 1GHz on early boot. We can remove this fix when smart hsdk pll driver will be introduced, see discussion: https://www.mail-archive.com/[email protected]/msg02689.html Signed-off-by: Eugeniy Paltsev <[email protected]> Signed-off-by: Vineet Gupta <[email protected]>
2017-10-03ARC: fix allnoconfig build warningVineet Gupta1-1/+1
Reported-by: Dmitrii Kolesnichenko <[email protected]> Signed-off-by: Vineet Gupta <[email protected]>
2017-10-03ARCv2: boot log: identify HS48 cores (dual issue)Vineet Gupta2-4/+16
Signed-off-by: Vineet Gupta <[email protected]>
2017-10-03ARC: boot log: decontaminate ARCv2 ISA_CONFIG registerVineet Gupta2-8/+15
ARCv2 ISA_CONFIG and ARC700_BUILD build config registers are not compatible. cpuinfo_arc had isa info placeholder which was mashup of bits form both. Untangle this by defining it off of ARCv2 ISA info and it is fine even for ARC700 since former is a super set of latter (ARC700 buildonly has 2 bits for atomics and stack check). At runtime, we treat ARCv2 ISA info as a generic placeholder but populate it correctly depending on ARC700 or HS. This paves way for adding more HS specific bits in isa info which was colliding with the extra bits for arc700. Signed-off-by: Vineet Gupta <[email protected]>
2017-10-03arc: remove redundant UTS_MACHINE define in arch/arc/MakefileMasahiro Yamada1-2/+0
The top-level Makefile sets the default of UTS_MACHINE to $(ARCH). If ARCH and UTS_MACHINE match, arch/$(ARCH)/Makefile need not specify UTS_MACHINE explicitly. Signed-off-by: Masahiro Yamada <[email protected]> Signed-off-by: Vineet Gupta <[email protected]>
2017-10-03ARC: [plat-eznps] Update platform maintainer as Noam leftVineet Gupta1-1/+2
Signed-off-by: Vineet Gupta <[email protected]>
2017-10-03ARC: [plat-hsdk] use actual clk driver to manage cpu clkEugeniy Paltsev2-3/+11
With corresponding clk driver now merged upstream, switch to it. - core_clk now represent the PLL (vs. fixed clk before) - input_clk represent the clk signal src for PLL (basically xtal) Signed-off-by: Eugeniy Paltsev <[email protected]> Signed-off-by: Vineet Gupta <[email protected]>
2017-10-03ARC: [*defconfig] Reenable soft lock-up detectorAlexey Brodkin7-7/+7
Commit 92e5aae45778 "kernel/watchdog: split up config options" introduced SOFTLOCKUP_DETECTOR which selects LOCKUP_DETECTOR instead of the latter to be selected itself. We need to adjust our defconfigs accordingly. Signed-off-by: Alexey Brodkin <[email protected]> Signed-off-by: Vineet Gupta <[email protected]>
2017-10-03ARC: [plat-axs10x] sdio: Temporary fix of sdio ciu frequencyEugeniy Paltsev1-1/+8
DW sdio controller has external ciu clock divider controlled via register in SDIO IP. It divides sdio_ref_clk (which comes from CGU) by 16 for default. So default mmcclk clock (which comes to sdk_in) is 25000000 Hz. So fix wrong current value (50000000 Hz) to actual 25000000 Hz. Note this is a preventive fix, in line with similar change for HSDK where this was actually needed. see: http://lists.infradead.org/pipermail/linux-snps-arc/2017-September/002924.html Signed-off-by: Eugeniy Paltsev <[email protected]> Signed-off-by: Vineet Gupta <[email protected]>
2017-10-03ARC: [plat-hsdk] sdio: Temporary fix of sdio ciu frequencyEugeniy Paltsev1-1/+11
DW sdio controller has external ciu clock divider controlled via register in SDIO IP. Due to its unexpected default value (it should divide by 1 but it divides by 8) SDIO IP uses wrong ciu clock and works unstable So add temporary fix and change clock frequency from 100000000 to 12500000 Hz until we fix dw sdio driver itself. Fixes SNPS STAR 9001204800 Signed-off-by: Eugeniy Paltsev <[email protected]> Signed-off-by: Vineet Gupta <[email protected]>
2017-10-03ARC: [plat-axs103] Add temporary quirk to reset ethernet IPEugeniy Paltsev1-0/+7
DW ethernet controller on AXS10x hangs sometimes after SW reset, so add temporary quirk to reset DW ethernet controller IP core. This quirk can be removed after axs10x reset driver (see http://patchwork.ozlabs.org/patch/800273/) or simple reset driver (see https://patchwork.kernel.org/patch/9903375/) will be available in upstream. Signed-off-by: Eugeniy Paltsev <[email protected]> Signed-off-by: Vineet Gupta <[email protected]>
2017-10-03Merge tag 'omap-for-v4.14/fixes-rc3' of ↵Olof Johansson6-18/+8
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes Fixes for omaps for v4.14-rc cycle Few minor fixes for omaps, mostly just boot time warning fixes: - Drop undocumented camera binding that got merged during the merge window by accident as I applied before Sakari's comments - Fix soft reset warning for dra7 kexec boot for gpio1 as the optional clocks need to be enabled for reset - Fix dra7 kexec boot clock rate for McASP as the rate is no longer the default rate after kexec - Fix omap3 pandora MMC warning during boot - Add am33xx SPI alias like we have on other SoCs - Remove node for non-existing CPSW EMAC Ethernet on am43xx-epos-evm * tag 'omap-for-v4.14/fixes-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: ARM: dts: am43xx-epos-evm: Remove extra CPSW EMAC entry ARM: dts: am33xx: Add spi alias to match SOC schematics ARM: OMAP2+: hsmmc: fix logic to call either omap_hsmmc_init or omap_hsmmc_late_init but not both ARM: dts: dra7: Set a default parent to mcasp3_ahclkx_mux ARM: OMAP2+: dra7xx: Set OPT_CLKS_IN_RESET flag for gpio1 ARM: dts: nokia n900: drop unneeded/undocumented parts of the dts Signed-off-by: Olof Johansson <[email protected]>
2017-10-03Merge tag 'v4.14-rockchip-dts64fixes-1' of ↵Olof Johansson2-73/+5
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes Adding the operating points on rk3368 like they were did not end up well for the boards as all of them are missing their cpu supplies, the OPPs actually need to follow the <target min max> format as the regulator is shared between both clusters and the one rk3368 board I have, somehow also doesn't like the higher opps at all - all of which I only realized after I brought my rk3368 board online again, after its bootloader broke. So we revert that OPP addition for now. And also two fixes for the mipi dsi controller on rk3399, which was referencing a clock to high up in the clock-tree so that an intermediate gate could be disabled inadvertently and also needs a clock for its area in the general register files of the rk3399 soc. * tag 'v4.14-rockchip-dts64fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: arm64: dts: rockchip: add the grf clk for dw-mipi-dsi on rk3399 arm64: dts: rockchip: Correct MIPI DPHY PLL clock on rk3399 Revert "arm64: dts: rockchip: Add basic cpu frequencies for RK3368" Signed-off-by: Olof Johansson <[email protected]>
2017-10-03Merge tag 'mvebu-fixes-4.14-1' of git://git.infradead.org/linux-mvebu into fixesOlof Johansson2-2/+8
mvebu fixes for 4.14 (part 1) Update MAINTAINERS for the Macchiatobin board (Armada 8K based) Fix AP806 system controller size on Armada 7K/8K * tag 'mvebu-fixes-4.14-1' of git://git.infradead.org/linux-mvebu: arm64: dt marvell: Fix AP806 system controller size MAINTAINERS: add Macchiatobin maintainers entry Signed-off-by: Olof Johansson <[email protected]>
2017-10-03Merge tag 'reset-fixes-for-4.14' of git://git.pengutronix.de/git/pza/linux ↵Olof Johansson7-47/+76
into fixes Reset controller fixes for v4.14 - Remove misleading HSDK v1 suffix, as there is no v2 planned - Add missing DT binding documentation for HSDK reset driver - Fix HSDK reset driver dependencies * tag 'reset-fixes-for-4.14' of git://git.pengutronix.de/git/pza/linux: reset: Restrict RESET_HSDK to ARC_SOC_HSDK or COMPILE_TEST ARC: reset: remove the misleading v1 suffix all over ARC: reset: add missing DT binding documentation for HSDKv1 reset driver ARC: reset: Only build on archs that have IOMEM Signed-off-by: Olof Johansson <[email protected]>
2017-10-03Merge tag 'davinci-fixes-for-v4.14' of ↵Olof Johansson1-0/+7
git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into fixes A fix for random ethernet mac address problem on DA850 EVM. * tag 'davinci-fixes-for-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci: ARM: dts: da850-evm: add serial and ethernet aliases Signed-off-by: Olof Johansson <[email protected]>
2017-10-03Merge tag 'at91-fixes' of ↵Olof Johansson2-10/+13
git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into fixes Fixes for 4.14: - three DT fixes for the newly introduced sama5d27_som1_ek board - one treewide modification that didn't touch this new PM code: we synchronize now to be coherent with the other ARM platforms * tag 'at91-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91: ARM: at91: Replace uses of virt_to_phys with __pa_symbol ARM: dts: at91: sama5d27_som1_ek: fix USB host vbus ARM: dts: at91: sama5d27_som1_ek: fix typos ARM: dts: at91: sama5d27_som1_ek: update pinmux/pinconf for LEDs and USB Signed-off-by: Olof Johansson <[email protected]>
2017-10-03ARM: defconfig: update Gemini defconfigLinus Walleij1-1/+2
This updates the Gemini defconfig with drivers merged for v4.13 or v4.14: - ATA driver is merged - DMA driver is merged - RTC driver gets selected from default Kconfig Signed-off-by: Linus Walleij <[email protected]> Signed-off-by: Olof Johansson <[email protected]>
2017-10-03ARM: defconfig: FRAMEBUFFER_CONSOLE can no longer be =mArnd Bergmann3-3/+3
It is no longer possible to load this at runtime, so let's change the few remaining users to have it built-in all the time. arch/arm/configs/zeus_defconfig:115:warning: symbol value 'm' invalid for FRAMEBUFFER_CONSOLE arch/arm/configs/viper_defconfig:116:warning: symbol value 'm' invalid for FRAMEBUFFER_CONSOLE arch/arm/configs/pxa_defconfig:474:warning: symbol value 'm' invalid for FRAMEBUFFER_CONSOLE Reported-by: kernelci.org bot <[email protected]> Fixes: 6104c37094e7 ("fbcon: Make fbcon a built-time depency for fbdev") Signed-off-by: Arnd Bergmann <[email protected]> Signed-off-by: Olof Johansson <[email protected]>
2017-10-03include/linux/fs.h: fix comment about struct address_spaceMike Rapoport1-1/+1
Before commit 9c5d760b8d22 ("mm: split gfp_mask and mapping flags into separate fields") the private_* fields of struct adrress_space were grouped together and using "ditto" in comments describing the last fields was correct. With introduction of gpf_mask between private_lock and private_list "ditto" references the wrong description. Fix it by using the elaborate description. Link: http://lkml.kernel.org/r/[email protected] Signed-off-by: Mike Rapoport <[email protected]> Cc: Michal Hocko <[email protected]> Signed-off-by: Andrew Morton <[email protected]> Signed-off-by: Linus Torvalds <[email protected]>
2017-10-03checkpatch: fix ignoring cover-letter logicStafford Horne1-1/+1
Currently running checkpatch on a directory with a cover-letter.patch file reports the following error: ----------------------------------------- patches/smp-v2/v2-0000-cover-letter.patch ----------------------------------------- ERROR: Does not appear to be a unified-diff format patch The logic to suppress the unified-diff check for cover letters is there but is checking $file instead of $filename. Fix the variable to use the correct one. Link: http://lkml.kernel.org/r/[email protected] Signed-off-by: Stafford Horne <[email protected]> Acked-by: Joe Perches <[email protected]> Signed-off-by: Andrew Morton <[email protected]> Signed-off-by: Linus Torvalds <[email protected]>
2017-10-03m32r: fix build failureSudip Mukherjee1-0/+9
The allmodconfig build of m32r is failing with the error: lib/mpi/mpih-div.o: In function 'mpihelp_divrem': mpih-div.c:(.text+0x40): undefined reference to 'abort' mpih-div.c:(.text+0x40): relocation truncated to fit: R_M32R_26_PCREL_RELA against undefined symbol 'abort' The function 'abort' was never defined for the m32r architecture. Create 'abort' as is done in other arch like 'arm' and 'unicore32'. Link: http://lkml.kernel.org/r/[email protected] Signed-off-by: Sudip Mukherjee <[email protected]> Signed-off-by: Andrew Morton <[email protected]> Signed-off-by: Linus Torvalds <[email protected]>
2017-10-03lib/ratelimit.c: use deferred printk() versionSergey Senozhatsky1-1/+3
printk_ratelimit() invokes ___ratelimit() which may invoke a normal printk() (pr_warn() in this particular case) to warn about suppressed output. Given that printk_ratelimit() may be called from anywhere, that pr_warn() is dangerous - it may end up deadlocking the system. Fix ___ratelimit() by using deferred printk(). Sasha reported the following lockdep error: : Unregister pv shared memory for cpu 8 : select_fallback_rq: 3 callbacks suppressed : process 8583 (trinity-c78) no longer affine to cpu8 : : ====================================================== : WARNING: possible circular locking dependency detected : 4.14.0-rc2-next-20170927+ #252 Not tainted : ------------------------------------------------------ : migration/8/62 is trying to acquire lock: : (&port_lock_key){-.-.}, at: serial8250_console_write() : : but task is already holding lock: : (&rq->lock){-.-.}, at: sched_cpu_dying() : : which lock already depends on the new lock. : : : the existing dependency chain (in reverse order) is: : : -> #3 (&rq->lock){-.-.}: : __lock_acquire() : lock_acquire() : _raw_spin_lock() : task_fork_fair() : sched_fork() : copy_process.part.31() : _do_fork() : kernel_thread() : rest_init() : start_kernel() : x86_64_start_reservations() : x86_64_start_kernel() : verify_cpu() : : -> #2 (&p->pi_lock){-.-.}: : __lock_acquire() : lock_acquire() : _raw_spin_lock_irqsave() : try_to_wake_up() : default_wake_function() : woken_wake_function() : __wake_up_common() : __wake_up_common_lock() : __wake_up() : tty_wakeup() : tty_port_default_wakeup() : tty_port_tty_wakeup() : uart_write_wakeup() : serial8250_tx_chars() : serial8250_handle_irq.part.25() : serial8250_default_handle_irq() : serial8250_interrupt() : __handle_irq_event_percpu() : handle_irq_event_percpu() : handle_irq_event() : handle_level_irq() : handle_irq() : do_IRQ() : ret_from_intr() : native_safe_halt() : default_idle() : arch_cpu_idle() : default_idle_call() : do_idle() : cpu_startup_entry() : rest_init() : start_kernel() : x86_64_start_reservations() : x86_64_start_kernel() : verify_cpu() : : -> #1 (&tty->write_wait){-.-.}: : __lock_acquire() : lock_acquire() : _raw_spin_lock_irqsave() : __wake_up_common_lock() : __wake_up() : tty_wakeup() : tty_port_default_wakeup() : tty_port_tty_wakeup() : uart_write_wakeup() : serial8250_tx_chars() : serial8250_handle_irq.part.25() : serial8250_default_handle_irq() : serial8250_interrupt() : __handle_irq_event_percpu() : handle_irq_event_percpu() : handle_irq_event() : handle_level_irq() : handle_irq() : do_IRQ() : ret_from_intr() : native_safe_halt() : default_idle() : arch_cpu_idle() : default_idle_call() : do_idle() : cpu_startup_entry() : rest_init() : start_kernel() : x86_64_start_reservations() : x86_64_start_kernel() : verify_cpu() : : -> #0 (&port_lock_key){-.-.}: : check_prev_add() : __lock_acquire() : lock_acquire() : _raw_spin_lock_irqsave() : serial8250_console_write() : univ8250_console_write() : console_unlock() : vprintk_emit() : vprintk_default() : vprintk_func() : printk() : ___ratelimit() : __printk_ratelimit() : select_fallback_rq() : sched_cpu_dying() : cpuhp_invoke_callback() : take_cpu_down() : multi_cpu_stop() : cpu_stopper_thread() : smpboot_thread_fn() : kthread() : ret_from_fork() : : other info that might help us debug this: : : Chain exists of: : &port_lock_key --> &p->pi_lock --> &rq->lock : : Possible unsafe locking scenario: : : CPU0 CPU1 : ---- ---- : lock(&rq->lock); : lock(&p->pi_lock); : lock(&rq->lock); : lock(&port_lock_key); : : *** DEADLOCK *** : : 4 locks held by migration/8/62: : #0: (&p->pi_lock){-.-.}, at: sched_cpu_dying() : #1: (&rq->lock){-.-.}, at: sched_cpu_dying() : #2: (printk_ratelimit_state.lock){....}, at: ___ratelimit() : #3: (console_lock){+.+.}, at: vprintk_emit() : : stack backtrace: : CPU: 8 PID: 62 Comm: migration/8 Not tainted 4.14.0-rc2-next-20170927+ #252 : Call Trace: : dump_stack() : print_circular_bug() : check_prev_add() : ? add_lock_to_list.isra.26() : ? check_usage() : ? kvm_clock_read() : ? kvm_sched_clock_read() : ? sched_clock() : ? check_preemption_disabled() : __lock_acquire() : ? __lock_acquire() : ? add_lock_to_list.isra.26() : ? debug_check_no_locks_freed() : ? memcpy() : lock_acquire() : ? serial8250_console_write() : _raw_spin_lock_irqsave() : ? serial8250_console_write() : serial8250_console_write() : ? serial8250_start_tx() : ? lock_acquire() : ? memcpy() : univ8250_console_write() : console_unlock() : ? __down_trylock_console_sem() : vprintk_emit() : vprintk_default() : vprintk_func() : printk() : ? show_regs_print_info() : ? lock_acquire() : ___ratelimit() : __printk_ratelimit() : select_fallback_rq() : sched_cpu_dying() : ? sched_cpu_starting() : ? rcutree_dying_cpu() : ? sched_cpu_starting() : cpuhp_invoke_callback() : ? cpu_disable_common() : take_cpu_down() : ? trace_hardirqs_off_caller() : ? cpuhp_invoke_callback() : multi_cpu_stop() : ? __this_cpu_preempt_check() : ? cpu_stop_queue_work() : cpu_stopper_thread() : ? cpu_stop_create() : smpboot_thread_fn() : ? sort_range() : ? schedule() : ? __kthread_parkme() : kthread() : ? sort_range() : ? kthread_create_on_node() : ret_from_fork() : process 9121 (trinity-c78) no longer affine to cpu8 : smpboot: CPU 8 is now offline Link: http://lkml.kernel.org/r/[email protected] Fixes: 6b1d174b0c27b ("ratelimit: extend to print suppressed messages on release") Signed-off-by: Sergey Senozhatsky <[email protected]> Reported-by: Sasha Levin <[email protected]> Reviewed-by: Petr Mladek <[email protected]> Cc: Peter Zijlstra <[email protected]> Cc: Thomas Gleixner <[email protected]> Cc: Ingo Molnar <[email protected]> Cc: Borislav Petkov <[email protected]> Cc: Steven Rostedt <[email protected]> Cc: <[email protected]> Signed-off-by: Andrew Morton <[email protected]> Signed-off-by: Linus Torvalds <[email protected]>
2017-10-03kernel/params.c: improve STANDARD_PARAM_DEF readabilityJean Delvare1-8/+8
Align the parameters passed to STANDARD_PARAM_DEF for clarity. Link: http://lkml.kernel.org/r/20170928162728.756143cc@endymion Signed-off-by: Jean Delvare <[email protected]> Suggested-by: Ingo Molnar <[email protected]> Acked-by: Ingo Molnar <[email protected]> Cc: Baoquan He <[email protected]> Cc: Michal Hocko <[email protected]> Signed-off-by: Andrew Morton <[email protected]> Signed-off-by: Linus Torvalds <[email protected]>
2017-10-03kernel/params.c: fix an overflow in param_attr_showJean Delvare1-10/+7
Function param_attr_show could overflow the buffer it is operating on. The buffer size is PAGE_SIZE, and the string returned by attribute->param->ops->get is generated by scnprintf(buffer, PAGE_SIZE, ...) so it could be PAGE_SIZE - 1 long, with the terminating '\0' at the very end of the buffer. Calling strcat(..., "\n") on this isn't safe, as the '\0' will be replaced by '\n' (OK) and then another '\0' will be added past the end of the buffer (not OK.) Simply add the trailing '\n' when writing the attribute contents to the buffer originally. This is safe, and also faster. Credits to Teradata for discovering this issue. Link: http://lkml.kernel.org/r/20170928162602.60c379c7@endymion Signed-off-by: Jean Delvare <[email protected]> Acked-by: Ingo Molnar <[email protected]> Cc: Baoquan He <[email protected]> Cc: Michal Hocko <[email protected]> Signed-off-by: Andrew Morton <[email protected]> Signed-off-by: Linus Torvalds <[email protected]>
2017-10-03kernel/params.c: fix the maximum length in param_get_stringJean Delvare1-1/+1
The length parameter of strlcpy() is supposed to reflect the size of the target buffer, not of the source string. Harmless in this case as the buffer is PAGE_SIZE long and the source string is always much shorter than this, but conceptually wrong, so let's fix it. Link: http://lkml.kernel.org/r/20170928162515.24846b4f@endymion Signed-off-by: Jean Delvare <[email protected]> Acked-by: Ingo Molnar <[email protected]> Cc: Baoquan He <[email protected]> Cc: Michal Hocko <[email protected]> Signed-off-by: Andrew Morton <[email protected]> Signed-off-by: Linus Torvalds <[email protected]>
2017-10-03mm/memory_hotplug: define find_{smallest|biggest}_section_pfn as unsigned longYASUAKI ISHIMATSU1-2/+2
find_{smallest|biggest}_section_pfn()s find the smallest/biggest section and return the pfn of the section. But the functions are defined as int. So the functions always return 0x00000000 - 0xffffffff. It means if memory address is over 16TB, the functions does not work correctly. To handle 64 bit value, the patch defines find_{smallest|biggest}_section_pfn() as unsigned long. Fixes: 815121d2b5cd ("memory_hotplug: clear zone when removing the memory") Link: http://lkml.kernel.org/r/[email protected] Signed-off-by: Yasuaki Ishimatsu <[email protected]> Acked-by: Michal Hocko <[email protected]> Cc: Xishi Qiu <[email protected]> Cc: Reza Arbab <[email protected]> Cc: Vlastimil Babka <[email protected]> Signed-off-by: Andrew Morton <[email protected]> Signed-off-by: Linus Torvalds <[email protected]>
2017-10-03mm/memory_hotplug: change pfn_to_section_nr/section_nr_to_pfn macro to ↵YASUAKI ISHIMATSU2-3/+9
inline function pfn_to_section_nr() and section_nr_to_pfn() are defined as macro. pfn_to_section_nr() has no issue even if it is defined as macro. But section_nr_to_pfn() has overflow issue if sec is defined as int. section_nr_to_pfn() just shifts sec by PFN_SECTION_SHIFT. If sec is defined as unsigned long, section_nr_to_pfn() returns pfn as 64 bit value. But if sec is defined as int, section_nr_to_pfn() returns pfn as 32 bit value. __remove_section() calculates start_pfn using section_nr_to_pfn() and scn_nr defined as int. So if hot-removed memory address is over 16TB, overflow issue occurs and section_nr_to_pfn() does not calculate correct pfn. To make callers use proper arg, the patch changes the macros to inline functions. Fixes: 815121d2b5cd ("memory_hotplug: clear zone when removing the memory") Link: http://lkml.kernel.org/r/[email protected] Signed-off-by: Yasuaki Ishimatsu <[email protected]> Acked-by: Michal Hocko <[email protected]> Cc: Xishi Qiu <[email protected]> Cc: Reza Arbab <[email protected]> Cc: Vlastimil Babka <[email protected]> Signed-off-by: Andrew Morton <[email protected]> Signed-off-by: Linus Torvalds <[email protected]>
2017-10-03kernel/kcmp.c: drop branch leftover typoCyrill Gorcunov1-1/+1
The else branch been left over and escaped the source code refresh. Not a problem but better clean it up. Fixes: 0791e3644e5e ("kcmp: add KCMP_EPOLL_TFD mode to compare epoll target files") Link: http://lkml.kernel.org/r/[email protected] Reported-by: Eugene Syromiatnikov <[email protected]> Signed-off-by: Cyrill Gorcunov <[email protected]> Acked-by: Andrei Vagin <[email protected]> Cc: Pavel Emelyanov <[email protected]> Signed-off-by: Andrew Morton <[email protected]> Signed-off-by: Linus Torvalds <[email protected]>
2017-10-03memremap: add scheduling point to devm_memremap_pagesMichal Hocko1-1/+3
devm_memremap_pages is initializing struct pages in for_each_device_pfn and that can take quite some time. We have even seen a soft lockup triggering on a non preemptive kernel NMI watchdog: BUG: soft lockup - CPU#61 stuck for 22s! [kworker/u641:11:1808] [...] RIP: 0010:[<ffffffff8118b6b7>] [<ffffffff8118b6b7>] devm_memremap_pages+0x327/0x430 [...] Call Trace: pmem_attach_disk+0x2fd/0x3f0 [nd_pmem] nvdimm_bus_probe+0x64/0x110 [libnvdimm] driver_probe_device+0x1f7/0x420 bus_for_each_drv+0x52/0x80 __device_attach+0xb0/0x130 bus_probe_device+0x87/0xa0 device_add+0x3fc/0x5f0 nd_async_device_register+0xe/0x40 [libnvdimm] async_run_entry_fn+0x43/0x150 process_one_work+0x14e/0x410 worker_thread+0x116/0x490 kthread+0xc7/0xe0 ret_from_fork+0x3f/0x70 fix this by adding cond_resched every 1024 pages. Link: http://lkml.kernel.org/r/[email protected] Signed-off-by: Michal Hocko <[email protected]> Reported-by: Johannes Thumshirn <[email protected]> Tested-by: Johannes Thumshirn <[email protected]> Cc: Dan Williams <[email protected]> Signed-off-by: Andrew Morton <[email protected]> Signed-off-by: Linus Torvalds <[email protected]>
2017-10-03mm, page_alloc: add scheduling point to memmap_init_zoneMichal Hocko1-0/+1
memmap_init_zone gets a pfn range to initialize and it can be really large resulting in a soft lockup on non-preemptible kernels NMI watchdog: BUG: soft lockup - CPU#31 stuck for 23s! [kworker/u642:5:1720] [...] task: ffff88ecd7e902c0 ti: ffff88eca4e50000 task.ti: ffff88eca4e50000 RIP: move_pfn_range_to_zone+0x185/0x1d0 [...] Call Trace: devm_memremap_pages+0x2c7/0x430 pmem_attach_disk+0x2fd/0x3f0 [nd_pmem] nvdimm_bus_probe+0x64/0x110 [libnvdimm] driver_probe_device+0x1f7/0x420 bus_for_each_drv+0x52/0x80 __device_attach+0xb0/0x130 bus_probe_device+0x87/0xa0 device_add+0x3fc/0x5f0 nd_async_device_register+0xe/0x40 [libnvdimm] async_run_entry_fn+0x43/0x150 process_one_work+0x14e/0x410 worker_thread+0x116/0x490 kthread+0xc7/0xe0 ret_from_fork+0x3f/0x70 Fix this by adding a scheduling point once per page block. Link: http://lkml.kernel.org/r/[email protected] Signed-off-by: Michal Hocko <[email protected]> Reported-by: Johannes Thumshirn <[email protected]> Tested-by: Johannes Thumshirn <[email protected]> Cc: Dan Williams <[email protected]> Signed-off-by: Andrew Morton <[email protected]> Signed-off-by: Linus Torvalds <[email protected]>
2017-10-03mm, memory_hotplug: add scheduling point to __add_pagesMichal Hocko1-0/+1
Patch series "mm, memory_hotplug: fix few soft lockups in memory hotadd". Johannes has noticed few soft lockups when adding a large nvdimm device. All of them were caused by a long loop without any explicit cond_resched which is a problem for !PREEMPT kernels. The fix is quite straightforward. Just make sure that cond_resched gets called from time to time. This patch (of 3): __add_pages gets a pfn range to add and there is no upper bound for a single call. This is usually a memory block aligned size for the regular memory hotplug - smaller sizes are usual for memory balloning drivers, or the whole NUMA node for physical memory online. There is no explicit scheduling point in that code path though. This can lead to long latencies while __add_pages is executed and we have even seen a soft lockup report during nvdimm initialization with !PREEMPT kernel NMI watchdog: BUG: soft lockup - CPU#11 stuck for 23s! [kworker/u641:3:832] [...] Workqueue: events_unbound async_run_entry_fn task: ffff881809270f40 ti: ffff881809274000 task.ti: ffff881809274000 RIP: _raw_spin_unlock_irqrestore+0x11/0x20 RSP: 0018:ffff881809277b10 EFLAGS: 00000286 [...] Call Trace: sparse_add_one_section+0x13d/0x18e __add_pages+0x10a/0x1d0 arch_add_memory+0x4a/0xc0 devm_memremap_pages+0x29d/0x430 pmem_attach_disk+0x2fd/0x3f0 [nd_pmem] nvdimm_bus_probe+0x64/0x110 [libnvdimm] driver_probe_device+0x1f7/0x420 bus_for_each_drv+0x52/0x80 __device_attach+0xb0/0x130 bus_probe_device+0x87/0xa0 device_add+0x3fc/0x5f0 nd_async_device_register+0xe/0x40 [libnvdimm] async_run_entry_fn+0x43/0x150 process_one_work+0x14e/0x410 worker_thread+0x116/0x490 kthread+0xc7/0xe0 ret_from_fork+0x3f/0x70 DWARF2 unwinder stuck at ret_from_fork+0x3f/0x70 Fix this by adding cond_resched once per each memory section in the given pfn range. Each section is constant amount of work which itself is not too expensive but many of them will just add up. Link: http://lkml.kernel.org/r/[email protected] Signed-off-by: Michal Hocko <[email protected]> Reported-by: Johannes Thumshirn <[email protected]> Tested-by: Johannes Thumshirn <[email protected]> Cc: Dan Williams <[email protected]> Signed-off-by: Andrew Morton <[email protected]> Signed-off-by: Linus Torvalds <[email protected]>
2017-10-03lib/idr.c: fix comment for idr_replace()Eric Biggers1-2/+2
idr_replace() returns the old value on success, not 0. Link: http://lkml.kernel.org/r/[email protected] Signed-off-by: Eric Biggers <[email protected]> Cc: Matthew Wilcox <[email protected]> Signed-off-by: Andrew Morton <[email protected]> Signed-off-by: Linus Torvalds <[email protected]>
2017-10-03mm: memcontrol: use vmalloc fallback for large kmem memcg arraysJohannes Weiner2-13/+21
For quick per-memcg indexing, slab caches and list_lru structures maintain linear arrays of descriptors. As the number of concurrent memory cgroups in the system goes up, this requires large contiguous allocations (8k cgroups = order-5, 16k cgroups = order-6 etc.) for every existing slab cache and list_lru, which can easily fail on loaded systems. E.g.: mkdir: page allocation failure: order:5, mode:0x14040c0(GFP_KERNEL|__GFP_COMP), nodemask=(null) CPU: 1 PID: 6399 Comm: mkdir Not tainted 4.13.0-mm1-00065-g720bbe532b7c-dirty #481 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-20170228_101828-anatol 04/01/2014 Call Trace: ? __alloc_pages_direct_compact+0x4c/0x110 __alloc_pages_nodemask+0xf50/0x1430 alloc_pages_current+0x60/0xc0 kmalloc_order_trace+0x29/0x1b0 __kmalloc+0x1f4/0x320 memcg_update_all_list_lrus+0xca/0x2e0 mem_cgroup_css_alloc+0x612/0x670 cgroup_apply_control_enable+0x19e/0x360 cgroup_mkdir+0x322/0x490 kernfs_iop_mkdir+0x55/0x80 vfs_mkdir+0xd0/0x120 SyS_mkdirat+0x6c/0xe0 SyS_mkdir+0x14/0x20 entry_SYSCALL_64_fastpath+0x18/0xad Mem-Info: active_anon:2965 inactive_anon:19 isolated_anon:0 active_file:100270 inactive_file:98846 isolated_file:0 unevictable:0 dirty:0 writeback:0 unstable:0 slab_reclaimable:7328 slab_unreclaimable:16402 mapped:771 shmem:52 pagetables:278 bounce:0 free:13718 free_pcp:0 free_cma:0 This output is from an artificial reproducer, but we have repeatedly observed order-7 failures in production in the Facebook fleet. These systems become useless as they cannot run more jobs, even though there is plenty of memory to allocate 128 individual pages. Use kvmalloc and kvzalloc to fall back to vmalloc space if these arrays prove too large for allocating them physically contiguous. Link: http://lkml.kernel.org/r/[email protected] Signed-off-by: Johannes Weiner <[email protected]> Reviewed-by: Josef Bacik <[email protected]> Acked-by: Michal Hocko <[email protected]> Acked-by: Vladimir Davydov <[email protected]> Signed-off-by: Andrew Morton <[email protected]> Signed-off-by: Linus Torvalds <[email protected]>
Powered by cgit, Gruvboxed by Blaster4385.