| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This patch prohibits performing of set commands on all hwmon attributes
through sysfs in ONEVF mode.
Signed-off-by: Danijel Slivka <[email protected]>
Acked-by: Harish Kasiviswanathan <[email protected]>
Reviewed-by: Harish Kasiviswanathan <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
Pull kvm fixes from Paolo Bonzini:
"x86 host:
- Expose KVM_CAP_ENABLE_CAP since it is supported
- Disable KVM_HC_CLOCK_PAIRING in TSC catchup mode
- Ensure async page fault token is nonzero
- Fix lockdep false negative
- Fix FPU migration regression from the AMX changes
x86 guest:
- Don't use PV TLB/IPI/yield on uniprocessor guests
PPC:
- reserve capability id (topic branch for ppc/kvm)"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: nSVM: disallow userspace setting of MSR_AMD64_TSC_RATIO to non default value when tsc scaling disabled
KVM: x86/mmu: make apf token non-zero to fix bug
KVM: PPC: reserve capability 210 for KVM_CAP_PPC_AIL_MODE_3
x86/kvm: Don't use pv tlb/ipi/sched_yield if on 1 vCPU
x86/kvm: Fix compilation warning in non-x86_64 builds
x86/kvm/fpu: Remove kvm_vcpu_arch.guest_supported_xcr0
x86/kvm/fpu: Limit guest user_xfeatures to supported bits of XCR0
kvm: x86: Disable KVM_HC_CLOCK_PAIRING if tsc is in always catchup mode
KVM: Fix lockdep false negative during host resume
KVM: x86: Add KVM_CAP_ENABLE_CAP to x86
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci fixes from Bjorn Helgaas:
- Fix a merge error that broke PCI device enumeration on mvebu
platforms, including Turris Omnia (Armada 385) (Pali Rohár)
- Avoid using ATS on all AMD Navi10 and Navi14 GPUs because some
VBIOSes don't account for "harvested" (disabled) parts of the chip
when initializing caches (Alex Deucher)
* tag 'pci-v5.17-fixes-5' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Mark all AMD Navi10 and Navi14 GPU ATS as broken
PCI: mvebu: Fix device enumeration regression
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from bpf and netfilter.
Current release - regressions:
- bpf: fix crash due to out of bounds access into reg2btf_ids
- mvpp2: always set port pcs ops, avoid null-deref
- eth: marvell: fix driver load from initrd
- eth: intel: revert "Fix reset bw limit when DCB enabled with 1 TC"
Current release - new code bugs:
- mptcp: fix race in overlapping signal events
Previous releases - regressions:
- xen-netback: revert hotplug-status changes causing devices to not
be configured
- dsa:
- avoid call to __dev_set_promiscuity() while rtnl_mutex isn't
held
- fix panic when removing unoffloaded port from bridge
- dsa: microchip: fix bridging with more than two member ports
Previous releases - always broken:
- bpf:
- fix crash due to incorrect copy_map_value when both spin lock
and timer are present in a single value
- fix a bpf_timer initialization issue with clang
- do not try bpf_msg_push_data with len 0
- add schedule points in batch ops
- nf_tables:
- unregister flowtable hooks on netns exit
- correct flow offload action array size
- fix a couple of memory leaks
- vsock: don't check owner in vhost_vsock_stop() while releasing
- gso: do not skip outer ip header in case of ipip and net_failover
- smc: use a mutex for locking "struct smc_pnettable"
- openvswitch: fix setting ipv6 fields causing hw csum failure
- mptcp: fix race in incoming ADD_ADDR option processing
- sysfs: add check for netdevice being present to speed_show
- sched: act_ct: fix flow table lookup after ct clear or switching
zones
- eth: intel: fixes for SR-IOV forwarding offloads
- eth: broadcom: fixes for selftests and error recovery
- eth: mellanox: flow steering and SR-IOV forwarding fixes
Misc:
- make __pskb_pull_tail() & pskb_carve_frag_list() drop_monitor
friends not report freed skbs as drops
- force inlining of checksum functions in net/checksum.h"
* tag 'net-5.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (85 commits)
net: mv643xx_eth: process retval from of_get_mac_address
ping: remove pr_err from ping_lookup
Revert "i40e: Fix reset bw limit when DCB enabled with 1 TC"
openvswitch: Fix setting ipv6 fields causing hw csum failure
ipv6: prevent a possible race condition with lifetimes
net/smc: Use a mutex for locking "struct smc_pnettable"
bnx2x: fix driver load from initrd
Revert "xen-netback: Check for hotplug-status existence before watching"
Revert "xen-netback: remove 'hotplug-status' once it has served its purpose"
net/mlx5e: Fix VF min/max rate parameters interchange mistake
net/mlx5e: Add missing increment of count
net/mlx5e: MPLSoUDP decap, fix check for unsupported matches
net/mlx5e: Fix MPLSoUDP encap to use MPLS action information
net/mlx5e: Add feature check for set fec counters
net/mlx5e: TC, Skip redundant ct clear actions
net/mlx5e: TC, Reject rules with forward and drop actions
net/mlx5e: TC, Reject rules with drop and modify hdr action
net/mlx5e: kTLS, Use CHECKSUM_UNNECESSARY for device-offloaded packets
net/mlx5e: Fix wrong return value on ioctl EEPROM query failure
net/mlx5: Fix possible deadlock on rule deletion
...
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
- Fix QGV handling on ADL-P+ (Ville Syrjälä)
- Fix bw atomic check when switching between SAGV vs. no SAGV (Ville Syrjälä)
- Disconnect PHYs left connected by BIOS on disabled ports (Imre Deak)
- Fix SAVG to no SAGV transitions on TGL+ (Ville Syrjälä)
- Print PHY name properly on calibration error (DG2) (Matt Roper)
Signed-off-by: Dave Airlie <[email protected]>
From: Tvrtko Ursulin <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/YhdyHwRWkOTWwlqi@tursulin-mobl2
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.18:
UAPI Changes:
Cross-subsystem Changes:
- Split out panel-lvds and lvds dt bindings .
- Put yes/no on/off disabled/enabled strings in linux/string_helpers.h
and use it in drivers and tomoyo.
- Clarify dma_fence_chain and dma_fence_array should never include eachother.
- Flatten chains in syncobj's.
- Don't double add in fbdev/defio when page is already enlisted.
- Don't sort deferred-I/O pages by default in fbdev.
Core Changes:
- Fix missing pm_runtime_put_sync in bridge.
- Set modifier support to only linear fb modifier if drivers don't
advertise support.
- As a result, we remove allow_fb_modifiers.
- Add missing clear for EDID Deep Color Modes in drm_reset_display_info.
- Assorted documentation updates.
- Warn once in drm_clflush if there is no arch support.
- Add missing select for dp helper in drm_panel_edp.
- Assorted small fixes.
- Improve fb-helper's clipping handling.
- Don't dump shmem mmaps in a core dump.
- Add accounting to ttm resource manager, and use it in amdgpu.
- Allow querying the detected eDP panel through debugfs.
- Add helpers for xrgb8888 to 8 and 1 bits gray.
- Improve drm's buddy allocator.
- Add selftests for the buddy allocator.
Driver Changes:
- Add support for nomodeset to a lot of drm drivers.
- Use drm_module_*_driver in a lot of drm drivers.
- Assorted small fixes to bridge/lt9611, v3d, vc4, vmwgfx, mxsfb, nouveau,
bridge/dw-hdmi, panfrost, lima, ingenic, sprd, bridge/anx7625, ti-sn65dsi86.
- Add bridge/it6505.
- Create DP and DVI-I connectors in ast.
- Assorted nouveau backlight fixes.
- Rework amdgpu reset handling.
- Add dt bindings for ingenic,jz4780-dw-hdmi.
- Support reading edid through aux channel in ingenic.
- Add a drm driver for Solomon SSD130x OLED displays.
- Add simple support for sharp LQ140M1JW46.
- Add more panels to nt35560.
Signed-off-by: Dave Airlie <[email protected]>
From: Maarten Lankhorst <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-next
Linux core:
-----------
iosys-map: Add offset to iosys_map_memcpy_to() (Lucas)
iosys-map: Add a few more helpers (Lucas)
i915 (display and core changes on drm-intel-next):
--------------------------------------------------
- Display's DBuf and watermark related fixes and improvements (Ville)
- More i915 header and other code clean-up (Jani)
- Display IPS fixes and improvements (Ville)
- OPRegion fixes and cleanups (Jani)
- Fix the plane end Y offset check for FBC (Ville)
- DP 128b/132b updates (Jani)
- Disable runtime pm wakeref tracking for the mock device selftest (Ville)
- Many display code clean-up while targeting to fix up DP DFP 4:2:0 handling (Ville)
- Bigjoiner state tracking and more bigjoiner related work (Ville)
- Update DMC_DEBUG3 register for DG1 (Chuansheng)
- SAGV fixes (Ville)
- More GT register cleanup (Matt)
- Fix build issue when using clang (Tong)
- Display DG2 fixes (Matt)
- ADL-P PHY related fixes (Imre)
- PSR2 fixes (Jose)
- Add PCH Support for Alder Lake N (Tejas)
drm-intel-gt-next (drm-intel-gt-next-2022-02-17):
-------------------------------------------------
UAPI Changes:
- Weak parallel submission support for execlists
Minimal implementation of the parallel submission support for
execlists backend that was previously only implemented for GuC.
Support one sibling non-virtual engine.
Core Changes:
- Two backmerges of drm/drm-next for header file renames/changes and
i915_regs reorganization
Driver Changes:
- Add new DG2 subplatform: DG2-G12 (Matt R)
- Add new DG2 workarounds (Matt R, Ram, Bruce)
- Handle pre-programmed WOPCM registers for DG2+ (Daniele)
- Update guc shim control programming on XeHP SDV+ (Daniele)
- Add RPL-S C0/D0 stepping information (Anusha)
- Improve GuC ADS initialization to work on ARM64 on dGFX (Lucas)
- Fix KMD and GuC race on accessing PMU busyness (Umesh)
- Use PM timestamp instead of RING TIMESTAMP for reference in PMU with GuC (Umesh)
- Report error on invalid reset notification from GuC (John)
- Avoid WARN splat by holding RPM wakelock during PXP unbind (Juston)
- Fixes to parallel submission implementation (Matt B.)
- Improve GuC loading status check/error reports (John)
- Tweak TTM LRU priority hint selection (Matt A.)
- Align the plane_vma to min_page_size of stolen mem (Ram)
- Introduce vma resources and implement async unbinding (Thomas)
- Use struct vma_resource instead of struct vma_snapshot (Thomas)
- Return some TTM accel move errors instead of trying memcpy move (Thomas)
- Fix a race between vma / object destruction and unbinding (Thomas)
- Remove short-term pins from execbuf (Maarten)
- Update to GuC version 69.0.3 (John, Michal Wa.)
- Improvements to GT reset paths in GuC backend (Matt B.)
- Use shrinker_release_pages instead of writeback in shmem object hooks (Matt A., Tvrtko)
- Use trylock instead of blocking lock when freeing GEM objects (Maarten)
- Allocate intel_engine_coredump_alloc with ALLOW_FAIL (Matt B.)
- Fixes to object unmapping and purging (Matt A)
- Check for wedged device in GuC backend (John)
- Avoid lockdep splat by locking dpt_obj around set_cache_level (Maarten)
- Allow dead vm to unbind vma's without lock (Maarten)
- s/engine->i915/i915/ for DG2 engine workarounds (Matt R)
- Use to_gt() helper for GGTT accesses (Michal Wi.)
- Selftest improvements (Matt B., Thomas, Ram)
- Coding style and compiler warning fixes (Matt B., Jasmine, Andi, Colin, Gustavo, Dan)
Signed-off-by: Dave Airlie <[email protected]>
From: Rodrigo Vivi <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Pull block fixes from Jens Axboe:
- NVMe pull request:
- send H2CData PDUs based on MAXH2CDATA (Varun Prakash)
- fix passthrough to namespaces with unsupported features (Christoph
Hellwig)
- Clear iocb->private at poll completion (Stefano)
* tag 'block-5.17-2022-02-24' of git://git.kernel.dk/linux-block:
nvme-tcp: send H2CData PDUs based on MAXH2CDATA
nvme: also mark passthrough-only namespaces ready in nvme_update_ns_info
nvme: don't return an error from nvme_configure_metadata
block: clear iocb->private in blkdev_bio_end_io_async()
|
|
It is easy to hit the below memory leaks in my TigerLake platform:
unreferenced object 0xffff927c8b91dbc0 (size 32):
comm "kworker/0:2", pid 112, jiffies 4294893323 (age 83.604s)
hex dump (first 32 bytes):
4e 41 4d 45 3d 49 4e 54 33 34 30 30 20 54 68 65 NAME=INT3400 The
72 6d 61 6c 00 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b a5 rmal.kkkkkkkkkk.
backtrace:
[<ffffffff9c502c3e>] __kmalloc_track_caller+0x2fe/0x4a0
[<ffffffff9c7b7c15>] kvasprintf+0x65/0xd0
[<ffffffff9c7b7d6e>] kasprintf+0x4e/0x70
[<ffffffffc04cb662>] int3400_notify+0x82/0x120 [int3400_thermal]
[<ffffffff9c8b7358>] acpi_ev_notify_dispatch+0x54/0x71
[<ffffffff9c88f1a7>] acpi_os_execute_deferred+0x17/0x30
[<ffffffff9c2c2c0a>] process_one_work+0x21a/0x3f0
[<ffffffff9c2c2e2a>] worker_thread+0x4a/0x3b0
[<ffffffff9c2cb4dd>] kthread+0xfd/0x130
[<ffffffff9c201c1f>] ret_from_fork+0x1f/0x30
Fix it by calling kfree() accordingly.
Fixes: 38e44da59130 ("thermal: int3400_thermal: process "thermal table changed" event")
Signed-off-by: Chuansheng Liu <[email protected]>
Cc: 4.14+ <[email protected]> # 4.14+
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
Pull io_uring fixes from Jens Axboe:
- Add a conditional schedule point in io_add_buffers() (Eric)
- Fix for a quiesce speedup merged in this release (Dylan)
- Don't convert to jiffies for event timeout waiting, it's way too
coarse when we accept a timespec as input (me)
* tag 'io_uring-5.17-2022-02-23' of git://git.kernel.dk/linux-block:
io_uring: disallow modification of rsrc_data during quiesce
io_uring: don't convert to jiffies for waiting on timeouts
io_uring: add a schedule point in io_add_buffers()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm
Pull ARM cpufreq fixes for 5.18-rc6 from Viresh Kumar:
"This fixes issues related to throttle IRQ for Qcom SoCs."
* 'cpufreq/arm/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
cpufreq: qcom-hw: Delay enabling throttle_irq
cpufreq: Reintroduce ready() callback
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull more x86 platform driver fixes from Hans de Goede:
"Two more fixes:
- Fix suspend/resume regression on AMD Cezanne APUs in >= 5.16
- Fix Microsoft Surface 3 battery readings"
* tag 'platform-drivers-x86-v5.17-4' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
surface: surface3_power: Fix battery readings on batteries without a serial number
platform/x86: amd-pmc: Set QOS during suspend on CZN w/ timer wakeup
|
|
Obtaining a MAC address may be deferred in cases when the MAC is stored
in an NVMEM block, for example, and it may not be ready upon the first
retrieval attempt and return EPROBE_DEFER.
It is also possible that a port that does not rely on NVMEM has been
already created when getting the defer request. Thus, also the resources
allocated previously must be freed when doing a roll-back.
Fixes: 76723bca2802 ("net: mv643xx_eth: add DT parsing support")
Signed-off-by: Mauri Sandberg <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
default value when tsc scaling disabled
If nested tsc scaling is disabled, MSR_AMD64_TSC_RATIO should
never have non default value.
Due to way nested tsc scaling support was implmented in qemu,
it would set this msr to 0 when nested tsc scaling was disabled.
Ignore that value for now, as it causes no harm.
Fixes: 5228eb96a487 ("KVM: x86: nSVM: implement nested TSC scaling")
Cc: [email protected]
Signed-off-by: Maxim Levitsky <[email protected]>
Message-Id: <[email protected]>
Signed-off-by: Paolo Bonzini <[email protected]>
|
|
In current async pagefault logic, when a page is ready, KVM relies on
kvm_arch_can_dequeue_async_page_present() to determine whether to deliver
a READY event to the Guest. This function test token value of struct
kvm_vcpu_pv_apf_data, which must be reset to zero by Guest kernel when a
READY event is finished by Guest. If value is zero meaning that a READY
event is done, so the KVM can deliver another.
But the kvm_arch_setup_async_pf() may produce a valid token with zero
value, which is confused with previous mention and may lead the loss of
this READY event.
This bug may cause task blocked forever in Guest:
INFO: task stress:7532 blocked for more than 1254 seconds.
Not tainted 5.10.0 #16
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:stress state:D stack: 0 pid: 7532 ppid: 1409
flags:0x00000080
Call Trace:
__schedule+0x1e7/0x650
schedule+0x46/0xb0
kvm_async_pf_task_wait_schedule+0xad/0xe0
? exit_to_user_mode_prepare+0x60/0x70
__kvm_handle_async_pf+0x4f/0xb0
? asm_exc_page_fault+0x8/0x30
exc_page_fault+0x6f/0x110
? asm_exc_page_fault+0x8/0x30
asm_exc_page_fault+0x1e/0x30
RIP: 0033:0x402d00
RSP: 002b:00007ffd31912500 EFLAGS: 00010206
RAX: 0000000000071000 RBX: ffffffffffffffff RCX: 00000000021a32b0
RDX: 000000000007d011 RSI: 000000000007d000 RDI: 00000000021262b0
RBP: 00000000021262b0 R08: 0000000000000003 R09: 0000000000000086
R10: 00000000000000eb R11: 00007fefbdf2baa0 R12: 0000000000000000
R13: 0000000000000002 R14: 000000000007d000 R15: 0000000000001000
Signed-off-by: Liang Zhang <[email protected]>
Message-Id: <[email protected]>
Cc: [email protected]
Signed-off-by: Paolo Bonzini <[email protected]>
|
|
As Jakub noticed, prints should be avoided on the datapath.
Also, as packets would never come to the else branch in
ping_lookup(), remove pr_err() from ping_lookup().
Fixes: 35a79e64de29 ("ping: fix the dif and sdif check in ping_lookup")
Reported-by: Jakub Kicinski <[email protected]>
Signed-off-by: Xin Long <[email protected]>
Link: https://lore.kernel.org/r/1ef3f2fcd31bd681a193b1fcf235eee1603819bd.1645674068.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Revert of a patch that instead of fixing a AQ error when trying
to reset BW limit introduced several regressions related to
creation and managing TC. Currently there are errors when creating
a TC on both PF and VF.
Error log:
[17428.783095] i40e 0000:3b:00.1: AQ command Config VSI BW allocation per TC failed = 14
[17428.783107] i40e 0000:3b:00.1: Failed configuring TC map 0 for VSI 391
[17428.783254] i40e 0000:3b:00.1: AQ command Config VSI BW allocation per TC failed = 14
[17428.783259] i40e 0000:3b:00.1: Unable to configure TC map 0 for VSI 391
This reverts commit 3d2504663c41104b4359a15f35670cfa82de1bbf.
Fixes: 3d2504663c41 (i40e: Fix reset bw limit when DCB enabled with 1 TC)
Signed-off-by: Mateusz Palczewski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Ipv6 ttl, label and tos fields are modified without first
pulling/pushing the ipv6 header, which would have updated
the hw csum (if available). This might cause csum validation
when sending the packet to the stack, as can be seen in
the trace below.
Fix this by updating skb->csum if available.
Trace resulted by ipv6 ttl dec and then sending packet
to conntrack [actions: set(ipv6(hlimit=63)),ct(zone=99)]:
[295241.900063] s_pf0vf2: hw csum failure
[295241.923191] Call Trace:
[295241.925728] <IRQ>
[295241.927836] dump_stack+0x5c/0x80
[295241.931240] __skb_checksum_complete+0xac/0xc0
[295241.935778] nf_conntrack_tcp_packet+0x398/0xba0 [nf_conntrack]
[295241.953030] nf_conntrack_in+0x498/0x5e0 [nf_conntrack]
[295241.958344] __ovs_ct_lookup+0xac/0x860 [openvswitch]
[295241.968532] ovs_ct_execute+0x4a7/0x7c0 [openvswitch]
[295241.979167] do_execute_actions+0x54a/0xaa0 [openvswitch]
[295242.001482] ovs_execute_actions+0x48/0x100 [openvswitch]
[295242.006966] ovs_dp_process_packet+0x96/0x1d0 [openvswitch]
[295242.012626] ovs_vport_receive+0x6c/0xc0 [openvswitch]
[295242.028763] netdev_frame_hook+0xc0/0x180 [openvswitch]
[295242.034074] __netif_receive_skb_core+0x2ca/0xcb0
[295242.047498] netif_receive_skb_internal+0x3e/0xc0
[295242.052291] napi_gro_receive+0xba/0xe0
[295242.056231] mlx5e_handle_rx_cqe_mpwrq_rep+0x12b/0x250 [mlx5_core]
[295242.062513] mlx5e_poll_rx_cq+0xa0f/0xa30 [mlx5_core]
[295242.067669] mlx5e_napi_poll+0xe1/0x6b0 [mlx5_core]
[295242.077958] net_rx_action+0x149/0x3b0
[295242.086762] __do_softirq+0xd7/0x2d6
[295242.090427] irq_exit+0xf7/0x100
[295242.093748] do_IRQ+0x7f/0xd0
[295242.096806] common_interrupt+0xf/0xf
[295242.100559] </IRQ>
[295242.102750] RIP: 0033:0x7f9022e88cbd
[295242.125246] RSP: 002b:00007f9022282b20 EFLAGS: 00000246 ORIG_RAX: ffffffffffffffda
[295242.132900] RAX: 0000000000000005 RBX: 0000000000000010 RCX: 0000000000000000
[295242.140120] RDX: 00007f9022282ba8 RSI: 00007f9022282a30 RDI: 00007f9014005c30
[295242.147337] RBP: 00007f9014014d60 R08: 0000000000000020 R09: 00007f90254a8340
[295242.154557] R10: 00007f9022282a28 R11: 0000000000000246 R12: 0000000000000000
[295242.161775] R13: 00007f902308c000 R14: 000000000000002b R15: 00007f9022b71f40
Fixes: 3fdbd1ce11e5 ("openvswitch: add ipv6 'set' action")
Signed-off-by: Paul Blakey <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
valid_lft, prefered_lft and tstamp are always accessed under the lock
"lock" in other places. Reading these without taking the lock may result
in inconsistencies regarding the calculation of the valid and preferred
variables since decisions are taken on these fields for those variables.
Signed-off-by: Niels Dossche <[email protected]>
Reviewed-by: David Ahern <[email protected]>
Signed-off-by: Niels Dossche <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
smc_pnetid_by_table_ib() uses read_lock() and then it calls smc_pnet_apply_ib()
which, in turn, calls mutex_lock(&smc_ib_devices.mutex).
read_lock() disables preemption. Therefore, the code acquires a mutex while in
atomic context and it leads to a SAC bug.
Fix this bug by replacing the rwlock with a mutex.
Reported-and-tested-by: [email protected]
Fixes: 64e28b52c7a6 ("net/smc: add pnet table namespace support")
Confirmed-by: Tony Lu <[email protected]>
Signed-off-by: Fabio M. De Francesco <[email protected]>
Acked-by: Karsten Graul <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Commit b7a49f73059f ("bnx2x: Utilize firmware 7.13.21.0") added
new firmware support in the driver with maintaining older firmware
compatibility. However, older firmware was not added in MODULE_FIRMWARE()
which caused missing firmware files in initrd image leading to driver load
failure from initrd. This patch adds MODULE_FIRMWARE() for older firmware
version to have firmware files included in initrd.
Fixes: b7a49f73059f ("bnx2x: Utilize firmware 7.13.21.0")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215627
Signed-off-by: Manish Chopra <[email protected]>
Signed-off-by: Alok Prasad <[email protected]>
Signed-off-by: Ariel Elior <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
This reverts commit 2afeec08ab5c86ae21952151f726bfe184f6b23d.
The reasoning in the commit was wrong - the code expected to setup the
watch even if 'hotplug-status' didn't exist. In fact, it relied on the
watch being fired the first time - to check if maybe 'hotplug-status' is
already set to 'connected'. Not registering a watch for non-existing
path (which is the case if hotplug script hasn't been executed yet),
made the backend not waiting for the hotplug script to execute. This in
turns, made the netfront think the interface is fully operational, while
in fact it was not (the vif interface on xen-netback side might not be
configured yet).
This was a workaround for 'hotplug-status' erroneously being removed.
But since that is reverted now, the workaround is not necessary either.
More discussion at
https://lore.kernel.org/xen-devel/[email protected]/T/#u
Signed-off-by: Marek Marczykowski-Górecki <[email protected]>
Reviewed-by: Paul Durrant <[email protected]>
Reviewed-by: Michael Brown <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
This reverts commit 1f2565780e9b7218cf92c7630130e82dcc0fe9c2.
The 'hotplug-status' node should not be removed as long as the vif
device remains configured. Otherwise the xen-netback would wait for
re-running the network script even if it was already called (in case of
the frontent re-connecting). But also, it _should_ be removed when the
vif device is destroyed (for example when unbinding the driver) -
otherwise hotplug script would not configure the device whenever it
re-appear.
Moving removal of the 'hotplug-status' node was a workaround for nothing
calling network script after xen-netback module is reloaded. But when
vif interface is re-created (on xen-netback unbind/bind for example),
the script should be called, regardless of who does that - currently
this case is not handled by the toolstack, and requires manual
script call. Keeping hotplug-status=connected to skip the call is wrong
and leads to not configured interface.
More discussion at
https://lore.kernel.org/xen-devel/[email protected]/T/#u
Signed-off-by: Marek Marczykowski-Górecki <[email protected]>
Reviewed-by: Paul Durrant <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
There is a big gap between inode_should_defrag() and autodefrag extent
size threshold. For inode_should_defrag() it has a flexible
@small_write value. For compressed extent is 16K, and for non-compressed
extent it's 64K.
However for autodefrag extent size threshold, it's always fixed to the
default value (256K).
This means, the following write sequence will trigger autodefrag to
defrag ranges which didn't trigger autodefrag:
pwrite 0 8k
sync
pwrite 8k 128K
sync
The latter 128K write will also be considered as a defrag target (if
other conditions are met). While only that 8K write is really
triggering autodefrag.
Such behavior can cause extra IO for autodefrag.
Close the gap, by copying the @small_write value into inode_defrag, so
that later autodefrag can use the same @small_write value which
triggered autodefrag.
With the existing transid value, this allows autodefrag really to scan
the ranges which triggered autodefrag.
Although this behavior change is mostly reducing the extent_thresh value
for autodefrag, I believe in the future we should allow users to specify
the autodefrag extent threshold through mount options, but that's an
other problem to consider in the future.
CC: [email protected] # 5.16+
Signed-off-by: Qu Wenruo <[email protected]>
Signed-off-by: David Sterba <[email protected]>
|
|
Pull NVMe fixes from Christoph:
"nvme fixes for Linux 5.17
- send H2CData PDUs based on MAXH2CDATA (Varun Prakash)
- fix passthrough to namespaces with unsupported features (me)"
* tag 'nvme-5.17-2022-02-24' of git://git.infradead.org/nvme:
nvme-tcp: send H2CData PDUs based on MAXH2CDATA
nvme: also mark passthrough-only namespaces ready in nvme_update_ns_info
nvme: don't return an error from nvme_configure_metadata
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.17-rc6
Here's a revert of a commit which erroneously added a device id used for
the EPP/MEM mode of ch341 devices.
Included are also some new modem device ids.
All have been in linux-next with no reported issues.
* tag 'usb-serial-5.17-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Telit LE910R1 compositions
USB: serial: option: add support for DW5829e
Revert "USB: serial: ch341: add new Product ID for CH341A"
|
|
number
The battery on the 2nd hand Surface 3 which I recently bought appears to
not have a serial number programmed in. This results in any I2C reads from
the registers containing the serial number failing with an I2C NACK.
This was causing mshw0011_bix() to fail causing the battery readings to
not work at all.
Ignore EREMOTEIO (I2C NACK) errors when retrieving the serial number and
continue with an empty serial number to fix this.
Fixes: b1f81b496b0d ("platform/x86: surface3_power: MSHW0011 rev-eng implementation")
BugLink: https://github.com/linux-surface/linux-surface/issues/608
Reviewed-by: Benjamin Tissoires <[email protected]>
Reviewed-by: Maximilian Luz <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
commit 59348401ebed ("platform/x86: amd-pmc: Add special handling for
timer based S0i3 wakeup") adds support for using another platform timer
in lieu of the RTC which doesn't work properly on some systems. This path
was validated and worked well before submission. During the 5.16-rc1 merge
window other patches were merged that caused this to stop working properly.
When this feature was used with 5.16-rc1 or later some OEM laptops with the
matching firmware requirements from that commit would shutdown instead of
program a timer based wakeup.
This was bisected to commit 8d89835b0467 ("PM: suspend: Do not pause
cpuidle in the suspend-to-idle path"). This wasn't supposed to cause any
negative impacts and also tested well on both Intel and ARM platforms.
However this changed the semantics of when CPUs are allowed to be in the
deepest state. For the AMD systems in question it appears this causes a
firmware crash for timer based wakeup.
It's hypothesized to be caused by the `amd-pmc` driver sending `OS_HINT`
and all the CPUs going into a deep state while the timer is still being
programmed. It's likely a firmware bug, but to avoid it don't allow setting
CPUs into the deepest state while using CZN timer wakeup path.
If later it's discovered that this also occurs from "regular" suspends
without a timer as well or on other silicon, this may be later expanded to
run in the suspend path for more scenarios.
Cc: [email protected] # 5.16+
Suggested-by: Rafael J. Wysocki <[email protected]>
Link: https://lore.kernel.org/linux-acpi/BL1PR12MB51570F5BD05980A0DCA1F3F4E23A9@BL1PR12MB5157.namprd12.prod.outlook.com/T/#mee35f39c41a04b624700ab2621c795367f19c90e
Fixes: 8d89835b0467 ("PM: suspend: Do not pause cpuidle in the suspend-to-idle path")
Fixes: 23f62d7ab25b ("PM: sleep: Pause cpuidle later and resume it earlier during system transitions")
Fixes: 59348401ebed ("platform/x86: amd-pmc: Add special handling for timer based S0i3 wakeup"
Reviewed-by: Rafael J. Wysocki <[email protected]>
Signed-off-by: Mario Limonciello <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Hans de Goede <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
|
|
There's no lock for rndis response list. It could cause list corruption
if there're two different list_add at the same time like below.
It's better to add in rndis_add_response / rndis_free_response
/ rndis_get_next_response to prevent any race condition on response list.
[ 361.894299] [1: irq/191-dwc3:16979] list_add corruption.
next->prev should be prev (ffffff80651764d0),
but was ffffff883dc36f80. (next=ffffff80651764d0).
[ 361.904380] [1: irq/191-dwc3:16979] Call trace:
[ 361.904391] [1: irq/191-dwc3:16979] __list_add_valid+0x74/0x90
[ 361.904401] [1: irq/191-dwc3:16979] rndis_msg_parser+0x168/0x8c0
[ 361.904409] [1: irq/191-dwc3:16979] rndis_command_complete+0x24/0x84
[ 361.904417] [1: irq/191-dwc3:16979] usb_gadget_giveback_request+0x20/0xe4
[ 361.904426] [1: irq/191-dwc3:16979] dwc3_gadget_giveback+0x44/0x60
[ 361.904434] [1: irq/191-dwc3:16979] dwc3_ep0_complete_data+0x1e8/0x3a0
[ 361.904442] [1: irq/191-dwc3:16979] dwc3_ep0_interrupt+0x29c/0x3dc
[ 361.904450] [1: irq/191-dwc3:16979] dwc3_process_event_entry+0x78/0x6cc
[ 361.904457] [1: irq/191-dwc3:16979] dwc3_process_event_buf+0xa0/0x1ec
[ 361.904465] [1: irq/191-dwc3:16979] dwc3_thread_interrupt+0x34/0x5c
Fixes: f6281af9d62e ("usb: gadget: rndis: use list_for_each_entry_safe")
Cc: stable <[email protected]>
Signed-off-by: Daehwan Jung <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The interrupt service routine registered for the gadget is a primary
handler which mask the interrupt source and a threaded handler which
handles the source of the interrupt. Since the threaded handler is
voluntary threaded, the IRQ-core does not disable bottom halves before
invoke the handler like it does for the forced-threaded handler.
Due to changes in networking it became visible that a network gadget's
completions handler may schedule a softirq which remains unprocessed.
The gadget's completion handler is usually invoked either in hard-IRQ or
soft-IRQ context. In this context it is enough to just raise the softirq
because the softirq itself will be handled once that context is left.
In the case of the voluntary threaded handler, there is nothing that
will process pending softirqs. Which means it remain queued until
another random interrupt (on this CPU) fires and handles it on its exit
path or another thread locks and unlocks a lock with the bh suffix.
Worst case is that the CPU goes idle and the NOHZ complains about
unhandled softirqs.
Disable bottom halves before acquiring the lock (and disabling
interrupts) and enable them after dropping the lock. This ensures that
any pending softirqs will handled right away.
Link: https://lkml.kernel.org/r/[email protected]
Fixes: e5f68b4a3e7b0 ("Revert "usb: dwc3: gadget: remove unnecessary _irqsave()"")
Cc: stable <[email protected]>
Reported-by: Marek Szyprowski <[email protected]>
Tested-by: Marek Szyprowski <[email protected]>
Signed-off-by: Sebastian Andrzej Siewior <[email protected]>
Link: https://lore.kernel.org/r/Yg/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Assure that host may not manipulate the index to point
past endpoint array.
Signed-off-by: Szymon Heidrich <[email protected]>
Cc: stable <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes 2022-02-22
This series provides bug fixes to mlx5 driver.
Please pull and let me know if there is any problem.
* tag 'mlx5-fixes-2022-02-23' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5e: Fix VF min/max rate parameters interchange mistake
net/mlx5e: Add missing increment of count
net/mlx5e: MPLSoUDP decap, fix check for unsupported matches
net/mlx5e: Fix MPLSoUDP encap to use MPLS action information
net/mlx5e: Add feature check for set fec counters
net/mlx5e: TC, Skip redundant ct clear actions
net/mlx5e: TC, Reject rules with forward and drop actions
net/mlx5e: TC, Reject rules with drop and modify hdr action
net/mlx5e: kTLS, Use CHECKSUM_UNNECESSARY for device-offloaded packets
net/mlx5e: Fix wrong return value on ioctl EEPROM query failure
net/mlx5: Fix possible deadlock on rule deletion
net/mlx5: Fix tc max supported prio for nic mode
net/mlx5: Fix wrong limitation of metadata match on ecpf
net/mlx5: Update log_max_qp value to be 17 at most
net/mlx5: DR, Fix the threshold that defines when pool sync is initiated
net/mlx5: DR, Don't allow match on IP w/o matching on full ethertype/ip_version
net/mlx5: DR, Fix slab-out-of-bounds in mlx5_cmd_dr_create_fte
net/mlx5: DR, Cache STE shadow memory
net/mlx5: Update the list of the PCI supported devices
====================
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
https://gitlab.freedesktop.org/agd5f/linux into drm-fixes
amd-drm-fixes-5.17-2022-02-23:
amdgpu:
- Display FP fix
- PCO powergating fix
- RDNA2 OEM SKU stability fixes
- Display PSR fix
- PCI ASPM fix
- Display link encoder fix for TEST_COMMIT
- Raven2 suspend/resume fix
- Fix a regression in virtual display support
- GPUVM eviction fix
Signed-off-by: Dave Airlie <[email protected]>
From: Alex Deucher <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
https://gitlab.freedesktop.org/drm/tegra into drm-fixes
drm/tegra: Fixes for v5.17-rc6
Contains a couple of fixes for Tegra186 suspend/resume, syncpoint
waiting, a build warning and eDP on older Tegra devices.
Signed-off-by: Dave Airlie <[email protected]>
From: Thierry Reding <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
* edid: Always set RGB444
* imx/dcss: Select GEM CMA helpers
* radeon: Fix some variables's type
* vc4: Fix codec cleanup; Fix PM reference counting
Signed-off-by: Dave Airlie <[email protected]>
From: Thomas Zimmermann <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Link: https://lkml.kernel.org/r/[email protected]
Fixes: 496082df01bb08a4 ("rtla: Add rtla osnoise man page")
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
Acked-by: Daniel Bristot de Oliveira <[email protected]>
Signed-off-by: Steven Rostedt (Google) <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
- Update some maintainers email addresses
- Fix handling of elfcorehdr reservation for crash dump kernel
- Fix unittest expected warnings text
* tag 'devicetree-fixes-for-5.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: update Roger Quadros email
MAINTAINERS: sifive: drop Yash Shah
of/fdt: move elfcorehdr reservation early for crash dump kernel
of: unittest: update text of expected warnings
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux
Pull selinux fix from Paul Moore:
"A second small SELinux fix which addresses an incorrect
mutex_is_locked() check"
* tag 'selinux-pr-20220223' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux:
selinux: fix misuse of mutex_is_locked()
|
|
The VF min and max rate were passed incorrectly and resulted in wrongly
interchanging them. Fix the order of parameters in
mlx5_esw_qos_set_vport_rate().
Fixes: d7df09f5e7b4 ("net/mlx5: E-switch, Enable vport QoS on demand")
Signed-off-by: Gal Pressman <[email protected]>
Reviewed-by: Aya Levin <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
Add mistakenly missing increment of count variable when looping over
output buffer in mlx5e_self_test().
This resolves the issue of garbage values output when querying with self
test via ethtool.
before:
$ ethtool -t eth2
The test result is PASS
The test extra info:
Link Test 0
Speed Test 1768697188
Health Test 758528120
Loopback Test 3288687
after:
$ ethtool -t eth2
The test result is PASS
The test extra info:
Link Test 0
Speed Test 0
Health Test 0
Loopback Test 0
Fixes: 7990b1b5e8bd ("net/mlx5e: loopback test is not supported in switchdev mode")
Signed-off-by: Lama Kayal <[email protected]>
Reviewed-by: Gal Pressman <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
Currently offload of rule on bareudp device require tunnel key
in order to match on mpls fields and without it the mpls fields
are ignored, this is incorrect due to the fact udp tunnel doesn't
have key to match on.
Fix by returning error in case flow is matching on tunnel key.
Fixes: 72046a91d134 ("net/mlx5e: Allow to match on mpls parameters")
Signed-off-by: Maor Dickman <[email protected]>
Reviewed-by: Roi Dayan <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
Currently the MPLSoUDP encap builds the MPLS header using encap action
information (tunnel id, ttl and tos) instead of the MPLS action
information (label, ttl, tc and bos) which is wrong.
Fix by storing the MPLS action information during the flow action
parse and later using it to create the encap MPLS header.
Fixes: f828ca6a2fb6 ("net/mlx5e: Add support for hw encapsulation of MPLS over UDP")
Signed-off-by: Maor Dickman <[email protected]>
Reviewed-by: Roi Dayan <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
Fec counters support is checked via the PCAM feature_cap_mask,
bit 0: PPCNT_counter_group_Phy_statistical_counter_group.
Add feature check to avoid faulty behavior.
Fixes: 0a1498ebfa55 ("net/mlx5e: Expose FEC counters via ethtool")
Signed-off-by: Lama Kayal <[email protected]>
Reviewed-by: Gal Pressman <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
Offload of ct clear action is just resetting the reg_c register.
It's done by allocating modify hdr resources which is limited.
Doing it multiple times is redundant and wasting modify hdr resources
and if resources depleted the driver will fail offloading the rule.
Ignore redundant ct clear actions after the first one.
Fixes: 806401c20a0f ("net/mlx5e: CT, Fix multiple allocations and memleak of mod acts")
Signed-off-by: Roi Dayan <[email protected]>
Reviewed-by: Ariel Levkovich <[email protected]>
Reviewed-by: Maor Dickman <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
Such rules are redundant but allowed and passed to the driver.
The driver does not support offloading such rules so return an error.
Fixes: 03a9d11e6eeb ("net/mlx5e: Add TC drop and mirred/redirect action parsing for SRIOV offloads")
Signed-off-by: Roi Dayan <[email protected]>
Reviewed-by: Oz Shlomo <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
This kind of action is not supported by firmware and generates a
syndrome.
kernel: mlx5_core 0000:08:00.0: mlx5_cmd_check:777:(pid 102063): SET_FLOW_TABLE_ENTRY(0x936) op_mod(0x0) failed, status bad parameter(0x3), syndrome (0x8708c3)
Fixes: d7e75a325cb2 ("net/mlx5e: Add offloading of E-Switch TC pedit (header re-write) actions")
Signed-off-by: Roi Dayan <[email protected]>
Reviewed-by: Maor Dickman <[email protected]>
Reviewed-by: Oz Shlomo <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
For RX TLS device-offloaded packets, the HW spec guarantees checksum
validation for the offloaded packets, but does not define whether the
CQE.checksum field matches the original packet (ciphertext) or
the decrypted one (plaintext). This latitude allows architetctural
improvements between generations of chips, resulting in different decisions
regarding the value type of CQE.checksum.
Hence, for these packets, the device driver should not make use of this CQE
field. Here we block CHECKSUM_COMPLETE usage for RX TLS device-offloaded
packets, and use CHECKSUM_UNNECESSARY instead.
Value of the packet's tcp_hdr.csum is not modified by the HW, and it always
matches the original ciphertext.
Fixes: 1182f3659357 ("net/mlx5e: kTLS, Add kTLS RX HW offload support")
Signed-off-by: Tariq Toukan <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
The ioctl EEPROM query wrongly returns success on read failures, fix
that by returning the appropriate error code.
Fixes: bb64143eee8c ("net/mlx5e: Add ethtool support for dump module EEPROM")
Signed-off-by: Gal Pressman <[email protected]>
Reviewed-by: Tariq Toukan <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
Add missing call to up_write_ref_node() which releases the semaphore
in case the FTE doesn't have destinations, such in drop rule case.
Fixes: 465e7baab6d9 ("net/mlx5: Fix deletion of duplicate rules")
Signed-off-by: Maor Gottlieb <[email protected]>
Reviewed-by: Mark Bloch <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
Only prio 1 is supported if firmware doesn't support ignore flow
level for nic mode. The offending commit removed the check wrongly.
Add it back.
Fixes: 9a99c8f1253a ("net/mlx5e: E-Switch, Offload all chain 0 priorities when modify header and forward action is not supported")
Signed-off-by: Chris Mi <[email protected]>
Reviewed-by: Roi Dayan <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|