| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
UBSAN triggers the following undefined behaviour warnings:
[...]
[ 13.236124] UBSAN: Undefined behaviour in drivers/net/ethernet/amazon/ena/ena_eth_com.c:468:22
[ 13.240043] shift exponent 64 is too large for 64-bit type 'long long unsigned int'
[...]
[ 13.744769] UBSAN: Undefined behaviour in drivers/net/ethernet/amazon/ena/ena_eth_com.c:373:4
[ 13.748694] shift exponent 64 is too large for 64-bit type 'long long unsigned int'
[...]
When splitting the address to high and low, GENMASK_ULL is used to generate
a bitmask with dma_addr_bits field from io_sq (in ena_com_prepare_tx and
ena_com_add_single_rx_desc).
The problem is that dma_addr_bits is not initialized with a proper value
(besides being cleared in ena_com_create_io_queue).
Assign dma_addr_bits the correct value that is stored in ena_dev when
initializing the SQ.
Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Gal Pressman <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The size of kvm's shadow page tables corresponds to the size of the
guest virtual machines on the system. Large VMs can spend a significant
amount of memory as shadow page tables which can not be left as system
memory overhead. So, account shadow page tables to the kmemcg.
[[email protected]: replace (GFP_KERNEL|__GFP_ACCOUNT) with GFP_KERNEL_ACCOUNT]
Link: http://lkml.kernel.org/r/[email protected]
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Shakeel Butt <[email protected]>
Cc: Michal Hocko <[email protected]>
Cc: Johannes Weiner <[email protected]>
Cc: Vladimir Davydov <[email protected]>
Cc: Paolo Bonzini <[email protected]>
Cc: Greg Thelen <[email protected]>
Cc: Radim Krčmář <[email protected]>
Cc: Peter Feiner <[email protected]>
Cc: <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
/sys/../zswap/stored_pages keeps rising in a zswap test with
"zswap.max_pool_percent=0" parameter. But it should not compress or
store pages any more since there is no space in the compressed pool.
Reproduce steps:
1. Boot kernel with "zswap.enabled=1"
2. Set the max_pool_percent to 0
# echo 0 > /sys/module/zswap/parameters/max_pool_percent
3. Do memory stress test to see if some pages have been compressed
# stress --vm 1 --vm-bytes $mem_available"M" --timeout 60s
4. Watching the 'stored_pages' number increasing or not
The root cause is:
When zswap_max_pool_percent is set to 0 via kernel parameter,
zswap_is_full() will always return true due to zswap_shrink(). But if
the shinking is able to reclain a page successfully the code then
proceeds to compressing/storing another page, so the value of
stored_pages will keep changing.
To solve the issue, this patch adds a zswap_is_full() check again after
zswap_shrink() to make sure it's now under the max_pool_percent, and to
not compress/store if we reached the limit.
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Li Wang <[email protected]>
Acked-by: Dan Streetman <[email protected]>
Cc: Seth Jennings <[email protected]>
Cc: Huang Ying <[email protected]>
Cc: Yu Zhao <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
The new gasket staging driver ran into a randconfig build failure when
CONFIG_EVENTFD is disabled:
In file included from drivers/staging/gasket/gasket_interrupt.h:11,
from drivers/staging/gasket/gasket_interrupt.c:4:
include/linux/eventfd.h: In function 'eventfd_ctx_fdget':
include/linux/eventfd.h:51:9: error: implicit declaration of function 'ERR_PTR' [-Werror=implicit-function-declaration]
I can't see anything wrong with including eventfd.h before err.h, so the
easiest fix is to make it possible to do this by including the file
where it is needed.
Link: http://lkml.kernel.org/r/[email protected]
Fixes: 9a69f5087ccc ("drivers/staging: Gasket driver framework + Apex driver")
Signed-off-by: Arnd Bergmann <[email protected]>
Cc: Eric Biggers <[email protected]>
Cc: Al Viro <[email protected]>
Cc: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
vma_is_anonymous() relies on ->vm_ops being NULL to detect anonymous
VMA. This is unreliable as ->mmap may not set ->vm_ops.
False-positive vma_is_anonymous() may lead to crashes:
next ffff8801ce5e7040 prev ffff8801d20eca50 mm ffff88019c1e13c0
prot 27 anon_vma ffff88019680cdd8 vm_ops 0000000000000000
pgoff 0 file ffff8801b2ec2d00 private_data 0000000000000000
flags: 0xff(read|write|exec|shared|mayread|maywrite|mayexec|mayshare)
------------[ cut here ]------------
kernel BUG at mm/memory.c:1422!
invalid opcode: 0000 [#1] SMP KASAN
CPU: 0 PID: 18486 Comm: syz-executor3 Not tainted 4.18.0-rc3+ #136
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google
01/01/2011
RIP: 0010:zap_pmd_range mm/memory.c:1421 [inline]
RIP: 0010:zap_pud_range mm/memory.c:1466 [inline]
RIP: 0010:zap_p4d_range mm/memory.c:1487 [inline]
RIP: 0010:unmap_page_range+0x1c18/0x2220 mm/memory.c:1508
Call Trace:
unmap_single_vma+0x1a0/0x310 mm/memory.c:1553
zap_page_range_single+0x3cc/0x580 mm/memory.c:1644
unmap_mapping_range_vma mm/memory.c:2792 [inline]
unmap_mapping_range_tree mm/memory.c:2813 [inline]
unmap_mapping_pages+0x3a7/0x5b0 mm/memory.c:2845
unmap_mapping_range+0x48/0x60 mm/memory.c:2880
truncate_pagecache+0x54/0x90 mm/truncate.c:800
truncate_setsize+0x70/0xb0 mm/truncate.c:826
simple_setattr+0xe9/0x110 fs/libfs.c:409
notify_change+0xf13/0x10f0 fs/attr.c:335
do_truncate+0x1ac/0x2b0 fs/open.c:63
do_sys_ftruncate+0x492/0x560 fs/open.c:205
__do_sys_ftruncate fs/open.c:215 [inline]
__se_sys_ftruncate fs/open.c:213 [inline]
__x64_sys_ftruncate+0x59/0x80 fs/open.c:213
do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Reproducer:
#include <stdio.h>
#include <stddef.h>
#include <stdint.h>
#include <stdlib.h>
#include <string.h>
#include <sys/types.h>
#include <sys/stat.h>
#include <sys/ioctl.h>
#include <sys/mman.h>
#include <unistd.h>
#include <fcntl.h>
#define KCOV_INIT_TRACE _IOR('c', 1, unsigned long)
#define KCOV_ENABLE _IO('c', 100)
#define KCOV_DISABLE _IO('c', 101)
#define COVER_SIZE (1024<<10)
#define KCOV_TRACE_PC 0
#define KCOV_TRACE_CMP 1
int main(int argc, char **argv)
{
int fd;
unsigned long *cover;
system("mount -t debugfs none /sys/kernel/debug");
fd = open("/sys/kernel/debug/kcov", O_RDWR);
ioctl(fd, KCOV_INIT_TRACE, COVER_SIZE);
cover = mmap(NULL, COVER_SIZE * sizeof(unsigned long),
PROT_READ | PROT_WRITE, MAP_SHARED, fd, 0);
munmap(cover, COVER_SIZE * sizeof(unsigned long));
cover = mmap(NULL, COVER_SIZE * sizeof(unsigned long),
PROT_READ | PROT_WRITE, MAP_PRIVATE, fd, 0);
memset(cover, 0, COVER_SIZE * sizeof(unsigned long));
ftruncate(fd, 3UL << 20);
return 0;
}
This can be fixed by assigning anonymous VMAs own vm_ops and not relying
on it being NULL.
If ->mmap() failed to set ->vm_ops, mmap_region() will set it to
dummy_vm_ops. This way we will have non-NULL ->vm_ops for all VMAs.
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Kirill A. Shutemov <[email protected]>
Reported-by: [email protected]
Acked-by: Linus Torvalds <[email protected]>
Reviewed-by: Andrew Morton <[email protected]>
Cc: Dmitry Vyukov <[email protected]>
Cc: Oleg Nesterov <[email protected]>
Cc: Andrea Arcangeli <[email protected]>
Cc: <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Make sure to initialize all VMAs properly, not only those which come
from vm_area_cachep.
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Kirill A. Shutemov <[email protected]>
Acked-by: Linus Torvalds <[email protected]>
Reviewed-by: Andrew Morton <[email protected]>
Cc: Dmitry Vyukov <[email protected]>
Cc: Oleg Nesterov <[email protected]>
Cc: Andrea Arcangeli <[email protected]>
Cc: <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Not all VMAs allocated with vm_area_alloc(). Some of them allocated on
stack or in data segment.
The new helper can be use to initialize VMA properly regardless where it
was allocated.
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Kirill A. Shutemov <[email protected]>
Acked-by: Linus Torvalds <[email protected]>
Reviewed-by: Andrew Morton <[email protected]>
Cc: Dmitry Vyukov <[email protected]>
Cc: Oleg Nesterov <[email protected]>
Cc: Andrea Arcangeli <[email protected]>
Cc: <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Commit e76384884344 ("mm: introduce MEMORY_DEVICE_FS_DAX and
CONFIG_DEV_PAGEMAP_OPS") added two EXPORT_SYMBOL_GPL() symbols, but
these symbols are required by the inlined put_page(), thus accidentally
making put_page() a GPL export only. This breaks OpenAFS (at least).
Mark them EXPORT_SYMBOL() instead.
Link: http://lkml.kernel.org/r/153128611970.2928.11310692420711601254.stgit@dwillia2-desk3.amr.corp.intel.com
Fixes: e76384884344 ("mm: introduce MEMORY_DEVICE_FS_DAX and CONFIG_DEV_PAGEMAP_OPS")
Signed-off-by: Dan Williams <[email protected]>
Reported-by: Joe Gorse <[email protected]>
Reported-by: John Hubbard <[email protected]>
Tested-by: Joe Gorse <[email protected]>
Tested-by: John Hubbard <[email protected]>
Cc: Jérôme Glisse <[email protected]>
Cc: Mark Vitale <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
In order for load/store tearing prevention to work, _all_ accesses to
the variable in question need to be done around READ and WRITE_ONCE()
macros. Ensure everyone does so for q->status variable for
semtimedop().
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Davidlohr Bueso <[email protected]>
Cc: Manfred Spraul <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
When pmem namespaces created are smaller than section size, this can
cause an issue during removal and gpf was observed:
general protection fault: 0000 1 SMP PTI
CPU: 36 PID: 3941 Comm: ndctl Tainted: G W 4.14.28-1.el7uek.x86_64 #2
task: ffff88acda150000 task.stack: ffffc900233a4000
RIP: 0010:__put_page+0x56/0x79
Call Trace:
devm_memremap_pages_release+0x155/0x23a
release_nodes+0x21e/0x260
devres_release_all+0x3c/0x48
device_release_driver_internal+0x15c/0x207
device_release_driver+0x12/0x14
unbind_store+0xba/0xd8
drv_attr_store+0x27/0x31
sysfs_kf_write+0x3f/0x46
kernfs_fop_write+0x10f/0x18b
__vfs_write+0x3a/0x16d
vfs_write+0xb2/0x1a1
SyS_write+0x55/0xb9
do_syscall_64+0x79/0x1ae
entry_SYSCALL_64_after_hwframe+0x3d/0x0
Add code to check whether we have a mapping already in the same section
and prevent additional mappings from being created if that is the case.
Link: http://lkml.kernel.org/r/152909478401.50143.312364396244072931.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Dave Jiang <[email protected]>
Cc: Dan Williams <[email protected]>
Cc: Robert Elliott <[email protected]>
Cc: Jeff Moyer <[email protected]>
Cc: Matthew Wilcox <[email protected]>
Cc: <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Building with KASAN and SLUB but without sysfs now results in a
build-time error:
WARNING: unmet direct dependencies detected for SLUB_DEBUG
Depends on [n]: SLUB [=y] && SYSFS [=n]
Selected by [y]:
- KASAN [=y] && HAVE_ARCH_KASAN [=y] && (SLUB [=y] || SLAB [=n] && !DEBUG_SLAB [=n]) && SLUB [=y]
mm/slub.c:4565:12: error: 'list_locations' defined but not used [-Werror=unused-function]
static int list_locations(struct kmem_cache *s, char *buf,
^~~~~~~~~~~~~~
mm/slub.c:4406:13: error: 'validate_slab_cache' defined but not used [-Werror=unused-function]
static long validate_slab_cache(struct kmem_cache *s)
This disallows that broken configuration in Kconfig.
Link: http://lkml.kernel.org/r/[email protected]
Fixes: dd275caf4a0d ("kasan: depend on CONFIG_SLUB_DEBUG")
Signed-off-by: Arnd Bergmann <[email protected]>
Cc: "Jason A. Donenfeld" <[email protected]>
Cc: Arnd Bergmann <[email protected]>
Cc: Shakeel Butt <[email protected]>
Cc: Andrey Ryabinin <[email protected]>
Cc: Christoph Lameter <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
While forking, if delayacct init fails due to memory shortage, it
continues expecting all delayacct users to check task->delays pointer
against NULL before dereferencing it, which all of them used to do.
Commit c96f5471ce7d ("delayacct: Account blkio completion on the correct
task"), while updating delayacct_blkio_end() to take the target task
instead of always using %current, made the function test NULL on
%current->delays and then continue to operated on @p->delays. If
%current succeeded init while @p didn't, it leads to the following
crash.
BUG: unable to handle kernel NULL pointer dereference at 0000000000000004
IP: __delayacct_blkio_end+0xc/0x40
PGD 8000001fd07e1067 P4D 8000001fd07e1067 PUD 1fcffbb067 PMD 0
Oops: 0000 [#1] SMP PTI
CPU: 4 PID: 25774 Comm: QIOThread0 Not tainted 4.16.0-9_fbk1_rc2_1180_g6b593215b4d7 #9
RIP: 0010:__delayacct_blkio_end+0xc/0x40
Call Trace:
try_to_wake_up+0x2c0/0x600
autoremove_wake_function+0xe/0x30
__wake_up_common+0x74/0x120
wake_up_page_bit+0x9c/0xe0
mpage_end_io+0x27/0x70
blk_update_request+0x78/0x2c0
scsi_end_request+0x2c/0x1e0
scsi_io_completion+0x20b/0x5f0
blk_mq_complete_request+0xa2/0x100
ata_scsi_qc_complete+0x79/0x400
ata_qc_complete_multiple+0x86/0xd0
ahci_handle_port_interrupt+0xc9/0x5c0
ahci_handle_port_intr+0x54/0xb0
ahci_single_level_irq_intr+0x3b/0x60
__handle_irq_event_percpu+0x43/0x190
handle_irq_event_percpu+0x20/0x50
handle_irq_event+0x2a/0x50
handle_edge_irq+0x80/0x1c0
handle_irq+0xaf/0x120
do_IRQ+0x41/0xc0
common_interrupt+0xf/0xf
Fix it by updating delayacct_blkio_end() check @p->delays instead.
Link: http://lkml.kernel.org/r/[email protected]
Fixes: c96f5471ce7d ("delayacct: Account blkio completion on the correct task")
Signed-off-by: Tejun Heo <[email protected]>
Reported-by: Dave Jones <[email protected]>
Debugged-by: Dave Jones <[email protected]>
Reviewed-by: Andrew Morton <[email protected]>
Cc: Josh Snyder <[email protected]>
Cc: <[email protected]> [4.15+]
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
git://git.pengutronix.de/git/pza/linux into drm-fixes
drm/imx: imx-drm ldb and ipu-v3 csi fixes
- Disable the LVDS Display Bridge (LDB) on driver bind. This is
necessary to guarantee correct LVDS signals in case the bootloader
left the LVDS output active.
- Remove false positive warning about disabled second LVDS channel in
dual-channel mode. In this mode, the second LVDS channel can not be
used separately. If the second channel is correctly described as
disabled in the device tree, the driver warned about this anyway.
- Fix the CSI confiuration to not only enable interlaced capture mode
for V4L2_FIELD_SEQ_BT and V4L2_FIELD_SEQ_TB, but also for the
V4L2_FIELD_ALTERNATE interlacing mode. Before, it incorrectly tried
to capture progressive frames in that case.
Signed-off-by: Dave Airlie <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
- Only a quirk for GLK NUC HDMI port issues
Signed-off-by: Dave Airlie <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
The current map_check_btf() in BPF_MAP_TYPE_ARRAY rejects
'> map->value_size' to ensure map_seq_show_elem() will not
access things beyond an array element.
Yonghong suggested that using '!=' is a more correct
check. The 8 bytes round_up on value_size is stored
in array->elem_size. Hence, using '!=' on map->value_size
is a proper check.
This patch also adds new tests to check the btf array
key type and value type. Two of these new tests verify
the btf's value_size (the change in this patch).
It also fixes two existing tests that wrongly encoded
a btf's type size (pprint_test) and the value_type_id (in one
of the raw_tests[]). However, that do not affect these two
BTF verification tests before or after this test changes.
These two tests mainly failed at array creation time after
this patch.
Fixes: a26ca7c982cb ("bpf: btf: Add pretty print support to the basic arraymap")
Suggested-by: Yonghong Song <[email protected]>
Acked-by: Yonghong Song <[email protected]>
Signed-off-by: Martin KaFai Lau <[email protected]>
Signed-off-by: Daniel Borkmann <[email protected]>
|
|
rhashtable_lookup() can return NULL. so that NULL pointer
check routine should be added.
Fixes: 02b55e5657c3 ("xdp: add MEM_TYPE_ZERO_COPY")
Signed-off-by: Taehee Yoo <[email protected]>
Acked-by: Martin KaFai Lau <[email protected]>
Acked-by: Björn Töpel <[email protected]>
Signed-off-by: Daniel Borkmann <[email protected]>
|
|
Registration of a memory region(MR) through FRMR/fastreg(unlike FMR)
needs a connection/qp. With a proxy qp, this dependency on connection
will be removed, but that needs more infrastructure patches, which is a
work in progress.
As an intermediate fix, the get_mr returns EOPNOTSUPP when connection
details are not populated. The MR registration through sendmsg() will
continue to work even with fast registration, since connection in this
case is formed upfront.
This patch fixes the following crash:
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] SMP KASAN
Modules linked in:
CPU: 1 PID: 4244 Comm: syzkaller468044 Not tainted 4.16.0-rc6+ #361
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
RIP: 0010:rds_ib_get_mr+0x5c/0x230 net/rds/ib_rdma.c:544
RSP: 0018:ffff8801b059f890 EFLAGS: 00010202
RAX: dffffc0000000000 RBX: ffff8801b07e1300 RCX: ffffffff8562d96e
RDX: 000000000000000d RSI: 0000000000000001 RDI: 0000000000000068
RBP: ffff8801b059f8b8 R08: ffffed0036274244 R09: ffff8801b13a1200
R10: 0000000000000004 R11: ffffed0036274243 R12: ffff8801b13a1200
R13: 0000000000000001 R14: ffff8801ca09fa9c R15: 0000000000000000
FS: 00007f4d050af700(0000) GS:ffff8801db300000(0000)
knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f4d050aee78 CR3: 00000001b0d9b006 CR4: 00000000001606e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
__rds_rdma_map+0x710/0x1050 net/rds/rdma.c:271
rds_get_mr_for_dest+0x1d4/0x2c0 net/rds/rdma.c:357
rds_setsockopt+0x6cc/0x980 net/rds/af_rds.c:347
SYSC_setsockopt net/socket.c:1849 [inline]
SyS_setsockopt+0x189/0x360 net/socket.c:1828
do_syscall_64+0x281/0x940 arch/x86/entry/common.c:287
entry_SYSCALL_64_after_hwframe+0x42/0xb7
RIP: 0033:0x4456d9
RSP: 002b:00007f4d050aedb8 EFLAGS: 00000246 ORIG_RAX: 0000000000000036
RAX: ffffffffffffffda RBX: 00000000006dac3c RCX: 00000000004456d9
RDX: 0000000000000007 RSI: 0000000000000114 RDI: 0000000000000004
RBP: 00000000006dac38 R08: 00000000000000a0 R09: 0000000000000000
R10: 0000000020000380 R11: 0000000000000246 R12: 0000000000000000
R13: 00007fffbfb36d6f R14: 00007f4d050af9c0 R15: 0000000000000005
Code: fa 48 c1 ea 03 80 3c 02 00 0f 85 cc 01 00 00 4c 8b bb 80 04 00 00
48
b8 00 00 00 00 00 fc ff df 49 8d 7f 68 48 89 fa 48 c1 ea 03 <80> 3c 02
00 0f
85 9c 01 00 00 4d 8b 7f 68 48 b8 00 00 00 00 00
RIP: rds_ib_get_mr+0x5c/0x230 net/rds/ib_rdma.c:544 RSP:
ffff8801b059f890
---[ end trace 7e1cea13b85473b0 ]---
Reported-by: [email protected]
Signed-off-by: Santosh Shilimkar <[email protected]>
Signed-off-by: Avinash Repaka <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Fix dev_change_tx_queue_len so it rolls back original value
upon a failure in dev_qdisc_change_tx_queue_len.
This is already done for notifirers' failures, share the code.
In case of failure in dev_qdisc_change_tx_queue_len, some tx queues
would still be of the new length, while they should be reverted.
Currently, the revert is not done, and is marked with a TODO label
in dev_qdisc_change_tx_queue_len, and should find some nice solution
to do it.
Yet it is still better to not apply the newly requested value.
Fixes: 48bfd55e7e41 ("net_sched: plug in qdisc ops change_tx_queue_len")
Signed-off-by: Tariq Toukan <[email protected]>
Reviewed-by: Eran Ben Elisha <[email protected]>
Reported-by: Ran Rozenstein <[email protected]>
Cc: Cong Wang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
non-sequential physical nodes
turbostat fails on some multi-package topologies because the logical node
enumeration assumes that the nodes are sequentially numbered,
which causes the logical numa nodes to not be enumerated, or enumerated incorrectly.
Use a more robust enumeration algorithm which allows for non-seqential physical nodes.
Signed-off-by: Prarit Bhargava <[email protected]>
Signed-off-by: Len Brown <[email protected]>
|
|
A recently added x2apic debug message was hard-coded to stderr.
That doesn't work with "-o outfile".
Signed-off-by: Len Brown <[email protected]>
|
|
This patch fixes a regression introduced in
commit 8cb48b32a5de ("tools/power turbostat: track thread ID in cpu_topology")
Turbostat uses incorrect cores number ('topo.num_cores') - its value is count
of logical CPUs, instead of count of physical cores. So it is twice as large as
it should be on a typical Intel system. For example, on a 6 core Xeon system
'topo.num_cores' is 12, and on a 52 core Xeon system 'topo.num_cores' is 104.
And interestingly, on a 68-core Knights Landing Intel system 'topo.num_cores'
is 272, because this system has 4 logical CPUs per core.
As a result, some of the turbostat calculations are incorrect. For example,
on idle 52-core Xeon system when all cores are ~99% in Core C6 (CPU%c6), the
summary (very first) line shows ~48% Core C6, while it should be ~99%.
This patch fixes the problem by fixing 'topo.num_cores' calculation.
Was:
1. Init 'thread_id' for all CPUs to -1
2. Run 'get_thread_siblings()' which sets it to 0 or 1
3. Increment 'topo.num_cores' when thread_id != -1 (bug!)
Now:
1. Init 'thread_id' for all CPUs to -1
2. Run 'get_thread_siblings()' which sets it to 0 or 1
3. Increment 'topo.num_cores' when thread_id is not 0
I did not have a chance to test this on an AMD machine, and only tested on a
couple of Intel Xeons (6 and 52 cores).
Reported-by: Vladislav Govtva <[email protected]>
Signed-off-by: Artem Bityutskiy <[email protected]>
Signed-off-by: Len Brown <[email protected]>
|
|
bio_iov_iter_get_pages() currently only adds pages for the next non-zero
segment from the iov_iter to the bio. That's suboptimal for callers,
which typically try to pin as many pages as fit into the bio. This patch
converts the current bio_iov_iter_get_pages() into a static helper, and
introduces a new helper that allocates as many pages as
1) fit into the bio,
2) are present in the iov_iter,
3) and can be pinned by MM.
Error is returned only if zero pages could be pinned. Because of 3), a
zero return value doesn't necessarily mean all pages have been pinned.
Callers that have to pin every page in the iov_iter must still call this
function in a loop (this is currently the case).
This change matters most for __blkdev_direct_IO_simple(), which calls
bio_iov_iter_get_pages() only once. If it obtains less pages than
requested, it returns a "short write" or "short read", and
__generic_file_write_iter() falls back to buffered writes, which may
lead to data corruption.
Fixes: 72ecad22d9f1 ("block: support a full bio worth of IO for simplified bdev direct-io")
Reviewed-by: Christoph Hellwig <[email protected]>
Signed-off-by: Martin Wilck <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
Fixes: 72ecad22d9f1 ("block: support a full bio worth of IO for simplified bdev direct-io")
Reviewed-by: Ming Lei <[email protected]>
Reviewed-by: Hannes Reinecke <[email protected]>
Reviewed-by: Christoph Hellwig <[email protected]>
Signed-off-by: Martin Wilck <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
If the last page of the bio is not "full", the length of the last
vector slot needs to be corrected. This slot has the index
(bio->bi_vcnt - 1), but only in bio->bi_io_vec. In the "bv" helper
array, which is shifted by the value of bio->bi_vcnt at function
invocation, the correct index is (nr_pages - 1).
v2: improved readability following suggestions from Ming Lei.
v3: followed a formatting suggestion from Christoph Hellwig.
Fixes: 2cefe4dbaadf ("block: add bio_iov_iter_get_pages()")
Reviewed-by: Hannes Reinecke <[email protected]>
Reviewed-by: Ming Lei <[email protected]>
Reviewed-by: Jan Kara <[email protected]>
Reviewed-by: Christoph Hellwig <[email protected]>
Signed-off-by: Martin Wilck <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
Pull NVMe fixes from Christoph:
"Two small fixes each for the FC code and the target."
* 'nvme-4.18' of git://git.infradead.org/nvme:
nvmet: only check for filebacking on -ENOTBLK
nvmet: fixup crash on NULL device path
nvme: if_ready checks to fail io to deleting controller
nvmet-fc: fix target sgl list on large transfers
|
|
When an fatal error is received by a non-bridge device, the device is
removed, and pci_stop_and_remove_bus_device() deallocates the device
structure. The freed device structure is used by subsequent code to send
uevents and print messages.
Hold a reference on the device until we're finished using it. This is not
an ideal fix because pcie_do_fatal_recovery() should not use the device at
all after removing it, but that's too big a project for right now.
Fixes: 7e9084b36740 ("PCI/AER: Handle ERR_FATAL with removal and re-enumeration of devices")
Signed-off-by: Thomas Tai <[email protected]>
[bhelgaas: changelog, reduce get/put coverage]
Signed-off-by: Bjorn Helgaas <[email protected]>
|
|
If we enable or disable xgbe flow-control by ethtool ,
it does't work.Because the parameter is not properly
assigned,so we need to adjust the assignment order
of the parameters.
Fixes: c1ce2f77366b ("amd-xgbe: Fix flow control setting logic")
Signed-off-by: tangpengpeng <[email protected]>
Acked-by: Tom Lendacky <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of USB fixes and new device ids for 4.18-rc7.
The largest number are a bunch of gadget driver fixes that got delayed
in being submitted earlier due to vacation schedules, but nothing
really huge is present in them. There are some new device ids and some
PHY driver fixes that were connected to some USB ones. Full details
are in the shortlog.
All have been in linux-next for a while with no reported issues"
* tag 'usb-4.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (28 commits)
usb: core: handle hub C_PORT_OVER_CURRENT condition
usb: xhci: Fix memory leak in xhci_endpoint_reset()
usb: typec: tcpm: Fix sink PDO starting index for PPS APDO selection
usb: gadget: f_fs: Only return delayed status when len is 0
usb: gadget: f_uac2: fix endianness of 'struct cntrl_*_lay3'
usb: dwc2: Fix inefficient copy of unaligned buffers
usb: dwc2: Fix DMA alignment to start at allocated boundary
usb: dwc3: rockchip: Fix PHY documentation links.
tools: usb: ffs-test: Fix build on big endian systems
usb: gadget: aspeed: Workaround memory ordering issue
usb: dwc3: gadget: remove redundant variable maxpacket
usb: dwc2: avoid NULL dereferences
usb/phy: fix PPC64 build errors in phy-fsl-usb.c
usb: dwc2: host: do not delay retries for CONTROL IN transfers
usb: gadget: u_audio: protect stream runtime fields with stream spinlock
usb: gadget: u_audio: remove cached period bytes value
usb: gadget: u_audio: remove caching of stream buffer parameters
usb: gadget: u_audio: update hw_ptr in iso_complete after data copied
usb: gadget: u_audio: fix pcm/card naming in g_audio_setup()
usb: gadget: f_uac2: fix error handling in afunc_bind (again)
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are three small staging driver fixes for 4.18-rc7.
One is a revert of an earlier patch that turned out to be incorrect,
one is a fix for the speakup drivers, and the last a fix for the
ks7010 driver to resolve a regression.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-4.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: speakup: fix wraparound in uaccess length check
staging: ks7010: call 'hostif_mib_set_request_int' instead of 'hostif_mib_set_request_bool'
Revert "staging:r8188eu: Use lib80211 to support TKIP"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fix from Greg KH:
"This is a single driver core fix for 4.18-rc7. It partially reverts a
previous commit to resolve some reported issues.
It has been in linux-next for a while now with no reported issues"
* tag 'driver-core-4.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
driver core: Partially revert "driver core: correct device's shutdown order"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"Fix a recent ACPICA regression causing the AML parser to get confused
and fail in some situations involving incorrect AML in an ACPI table
(Erik Schmauss)"
* tag 'acpi-4.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPICA: AML Parser: ignore dispatcher error status during table load
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fix from Rafael Wysocki:
"Fix up the recently introduced cpufreq driver for Qualcomm Kryo
processors by adding a terminating NULL entry to its table of device
IDs (YueHaibing)"
* tag 'pm-4.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: qcom-kryo: add NULL entry to the end of_device_id array
|
|
There is a window for racing when printing directly to task->comm,
allowing other threads to see a non-terminated string. The vsnprintf
function fills the buffer, counts the truncated chars, then finally
writes the \0 at the end.
creator other
vsnprintf:
fill (not terminated)
count the rest trace_sched_waking(p):
... memcpy(comm, p->comm, TASK_COMM_LEN)
write \0
The consequences depend on how 'other' uses the string. In our case,
it was copied into the tracing system's saved cmdlines, a buffer of
adjacent TASK_COMM_LEN-byte buffers (note the 'n' where 0 should be):
crash-arm64> x/1024s savedcmd->saved_cmdlines | grep 'evenk'
0xffffffd5b3818640: "irq/497-pwr_evenkworker/u16:12"
...and a strcpy out of there would cause stack corruption:
[224761.522292] Kernel panic - not syncing: stack-protector:
Kernel stack is corrupted in: ffffff9bf9783c78
crash-arm64> kbt | grep 'comm\|trace_print_context'
#6 0xffffff9bf9783c78 in trace_print_context+0x18c(+396)
comm (char [16]) = "irq/497-pwr_even"
crash-arm64> rd 0xffffffd4d0e17d14 8
ffffffd4d0e17d14: 2f71726900000000 5f7277702d373934 ....irq/497-pwr_
ffffffd4d0e17d24: 726f776b6e657665 3a3631752f72656b evenkworker/u16:
ffffffd4d0e17d34: f9780248ff003231 cede60e0ffffff9b 12..H.x......`..
ffffffd4d0e17d44: cede60c8ffffffd4 00000fffffffffd4 .....`..........
The workaround in e09e28671 (use strlcpy in __trace_find_cmdline) was
likely needed because of this same bug.
Solved by vsnprintf:ing to a local buffer, then using set_task_comm().
This way, there won't be a window where comm is not terminated.
Link: http://lkml.kernel.org/r/[email protected]
Cc: [email protected]
Fixes: bc0c38d139ec7 ("ftrace: latency tracer infrastructure")
Reviewed-by: Steven Rostedt (VMware) <[email protected]>
Signed-off-by: Snild Dolkow <[email protected]>
Signed-off-by: Steven Rostedt (VMware) <[email protected]>
|
|
Currently we are leaking bpf programs when they are detached from the
lirc device; the refcount never reaches zero.
Signed-off-by: Sean Young <[email protected]>
Signed-off-by: Mauro Carvalho Chehab <[email protected]>
|
|
Break statements were missing for Geneve case in
ndo_udp_tunnel_{add/del}, thereby raw mac matchall
entries were not getting added.
Fixes: c746fc0e8b2d("cxgb4: add geneve offload support for T6")
Signed-off-by: Arjun Vynipadath <[email protected]>
Signed-off-by: Ganesh Goudar <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Devlink resources registered with devlink_resource_register() have
to be unregistered.
Fixes: 37923ed6b8ce ("netdevsim: Add simple FIB resource controller via devlink")
Signed-off-by: Jakub Kicinski <[email protected]>
Reviewed-by: Quentin Monnet <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Commit 57ea2a34adf4 ("tracing/kprobes: Fix trace_probe flags on
enable_trace_kprobe() failure") added an if statement that depends on another
if statement that gcc doesn't see will initialize the "link" variable and
gives the warning:
"warning: 'link' may be used uninitialized in this function"
It is really a false positive, but to quiet the warning, and also to make
sure that it never actually is used uninitialized, initialize the "link"
variable to NULL and add an if (!WARN_ON_ONCE(!link)) where the compiler
thinks it could be used uninitialized.
Cc: [email protected]
Fixes: 57ea2a34adf4 ("tracing/kprobes: Fix trace_probe flags on enable_trace_kprobe() failure")
Reported-by: kbuild test robot <[email protected]>
Signed-off-by: Steven Rostedt (VMware) <[email protected]>
|
|
There was a case that triggered a double free in event_trigger_callback()
due to the called reg() function freeing the trigger_data and then it
getting freed again by the error return by the caller. The solution there
was to up the trigger_data ref count.
Code inspection found that event_enable_trigger_func() has the same issue,
but is not as easy to trigger (requires harder to trigger failures). It
needs to be solved slightly different as it needs more to clean up when the
reg() function fails.
Link: http://lkml.kernel.org/r/[email protected]
Cc: [email protected]
Fixes: 7862ad1846e99 ("tracing: Add 'enable_event' and 'disable_event' event trigger commands")
Reivewed-by: Masami Hiramatsu <[email protected]>
Signed-off-by: Steven Rostedt (VMware) <[email protected]>
|
|
Polling for the ingress queues relies on reading the producer/consumer
pointers of the Rx queue.
Prior this commit, a cached consumer pointer could be used, instead of
the actual consumer pointer and therefore report POLLIN prematurely.
This patch makes sure that the non-cached consumer pointer is used
instead.
Reported-by: Qi Zhang <[email protected]>
Tested-by: Qi Zhang <[email protected]>
Fixes: c497176cb2e4 ("xsk: add Rx receive functions and poll support")
Signed-off-by: Björn Töpel <[email protected]>
Signed-off-by: Daniel Borkmann <[email protected]>
|
|
Commit 24dea04767e6 ("bpf, x32: remove ld_abs/ld_ind")
removed the 4 /* Extra space for skb_copy_bits buffer */
from _STACK_SIZE, but it didn't fix the concerned code
in emit_prologue and emit_epilogue, and this error will
bring very strange kernel runtime errors. This patch
fixes it.
Fixes: 24dea04767e6 ("bpf, x32: remove ld_abs/ld_ind")
Reported-by: Meelis Roos <[email protected]>
Bisected-by: Meelis Roos <[email protected]>
Signed-off-by: Wang YanQing <[email protected]>
Signed-off-by: Daniel Borkmann <[email protected]>
|
|
Fixes the following sparse warnings:
net/ipv4/igmp.c:1391:6: warning:
symbol '__ip_mc_inc_group' was not declared. Should it be static?
Fixes: 6e2059b53f98 ("ipv4/igmp: init group mode as INCLUDE when join source group")
Signed-off-by: Wei Yongjun <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
We observed high 99 and 99.9% latencies when doing RPCs with DCTCP. The
problem is triggered when the last packet of a request arrives CE
marked. The reply will carry the ECE mark causing TCP to shrink its cwnd
to 1 (because there are no packets in flight). When the 1st packet of
the next request arrives, the ACK was sometimes delayed even though it
is CWR marked, adding up to 40ms to the RPC latency.
This patch insures that CWR marked data packets arriving will be acked
immediately.
Packetdrill script to reproduce the problem:
0.000 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
0.000 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
0.000 setsockopt(3, SOL_TCP, TCP_CONGESTION, "dctcp", 5) = 0
0.000 bind(3, ..., ...) = 0
0.000 listen(3, 1) = 0
0.100 < [ect0] SEW 0:0(0) win 32792 <mss 1000,sackOK,nop,nop,nop,wscale 7>
0.100 > SE. 0:0(0) ack 1 <mss 1460,nop,nop,sackOK,nop,wscale 8>
0.110 < [ect0] . 1:1(0) ack 1 win 257
0.200 accept(3, ..., ...) = 4
0.200 < [ect0] . 1:1001(1000) ack 1 win 257
0.200 > [ect01] . 1:1(0) ack 1001
0.200 write(4, ..., 1) = 1
0.200 > [ect01] P. 1:2(1) ack 1001
0.200 < [ect0] . 1001:2001(1000) ack 2 win 257
0.200 write(4, ..., 1) = 1
0.200 > [ect01] P. 2:3(1) ack 2001
0.200 < [ect0] . 2001:3001(1000) ack 3 win 257
0.200 < [ect0] . 3001:4001(1000) ack 3 win 257
0.200 > [ect01] . 3:3(0) ack 4001
0.210 < [ce] P. 4001:4501(500) ack 3 win 257
+0.001 read(4, ..., 4500) = 4500
+0 write(4, ..., 1) = 1
+0 > [ect01] PE. 3:4(1) ack 4501
+0.010 < [ect0] W. 4501:5501(1000) ack 4 win 257
// Previously the ACK sequence below would be 4501, causing a long RTO
+0.040~+0.045 > [ect01] . 4:4(0) ack 5501 // delayed ack
+0.311 < [ect0] . 5501:6501(1000) ack 4 win 257 // More data
+0 > [ect01] . 4:4(0) ack 6501 // now acks everything
+0.500 < F. 9501:9501(0) ack 4 win 257
Modified based on comments by Neal Cardwell <[email protected]>
Signed-off-by: Lawrence Brakmo <[email protected]>
Acked-by: Neal Cardwell <[email protected]>
Acked-by: Yuchung Cheng <[email protected]>
Signed-off-by: Eric Dumazet <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
On GLK NUC platforms the HDMI retiming buffer needs additional disabled
time to correctly sync to a faster incoming signal.
When measured on a scope the highspeed lines of the HDMI clock turn off
for ~400uS during a normal resolution change. The HDMI retimer on the
GLK NUC appears to require at least a full frame of quiet time before a
new faster clock can be correctly sync'd. Wait 100ms due to msleep
inaccuracies while waiting for a completed frame. Add a quirk to the
driver for GLK boards that use ITE66317 HDMI retimers.
V2: Add more devices to the quirk list
V3: Delay increased to 100ms, check to confirm crtc type is HDMI.
V4: crtc type check extended to include _DDI and whitespace fixes
v5: Fix white spaces, remove the macro for delay. Revert the crtc type
check introduced in v4.
Cc: Imre Deak <[email protected]>
Cc: <[email protected]> # v4.14+
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105887
Signed-off-by: Clint Taylor <[email protected]>
Tested-by: Daniel Scheller <[email protected]>
Signed-off-by: Radhakrishna Sripada <[email protected]>
Signed-off-by: Imre Deak <[email protected]>
Reviewed-by: Imre Deak <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
(cherry picked from commit 90c3e2198777aaa355b6994a31a79c636c8d4306)
Signed-off-by: Rodrigo Vivi <[email protected]>
|
|
Otherwise interfaces get exposed under /sys/devices/virtual, which
doesn't give udev the context it needs for PCI-based predictable
interface names.
Signed-off-by: dann frazier <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
When received packets are dropped in virtio_net driver, received packets
counter is incremented but bytes counter is not.
As a result, for instance if we drop all packets by XDP, only received
is counted and bytes stays 0, which looks inconsistent.
IMHO received packets/bytes should be counted if packets are produced by
the hypervisor, like what common NICs on physical machines are doing.
So fix the bytes counter.
Signed-off-by: Toshiaki Makita <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This is needed to ensure ->is_unity is correct when the plane was
previously configured to output a multi-planar format with scaling
enabled, and is then being reconfigured to output a uniplanar format.
Fixes: fc04023fafec ("drm/vc4: Add support for YUV planes.")
Cc: <[email protected]>
Signed-off-by: Boris Brezillon <[email protected]>
Reviewed-by: Eric Anholt <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
gcc happy
drm_atomic_helper_async_check() declares the plane, old_plane_state and
new_plane_state variables to iterate over all planes of the atomic
state and make sure only one plane is enabled.
Unfortunately gcc is not smart enough to figure out that the check on
n_planes is enough to guarantee that plane, new_plane_state and
old_plane_state are initialized.
Explicitly initialize those variables to NULL to make gcc happy.
Fixes: fef9df8b5945 ("drm/atomic: initial support for asynchronous plane update")
Cc: <[email protected]>
Signed-off-by: Boris Brezillon <[email protected]>
Reviewed-by: Sean Paul <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Async plane update is supposed to work only when updating the FB or FB
position of an already enabled plane. That does not apply to requests
where the plane was previously disabled or assigned to a different
CTRC.
Check old_plane_state->crtc value to make sure async plane update is
allowed.
Fixes: fef9df8b5945 ("drm/atomic: initial support for asynchronous plane update")
Cc: <[email protected]>
Signed-off-by: Boris Brezillon <[email protected]>
Reviewed-by: Eric Anholt <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"One more round of updates for problems seen this -rc series. Drivers
fixes are:
- Amlogic Meson audio divider fix and CPU clk critical marking
- Qualcomm multimedia GDSC marked as 'always on' to keep display
working
- Aspeed fixes for critical clks, resets causing clks to stay
disabled, and an incorrect HPLL frequency calculation
- Marvell Armada 3700 cpu clks would undervolt when switching from
low frequencies to high frequencies because the voltage didn't
stabilize in time so now we switch to an intermediate frequency
Plus we have a core framework thinko that messed up the debugfs flag
printing logic to make it not very useful"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: aspeed: Support HPLL strapping on ast2400
clk: mvebu: armada-37xx-periph: Fix switching CPU rate from 300Mhz to 1.2GHz
clk: aspeed: Mark bclk (PCIe) and dclk (VGA) as critical
clk/mmcc-msm8996: Make mmagic_bimc_gdsc ALWAYS_ON
clk: aspeed: Treat a gate in reset as disabled
clk: Really show symbolic clock flags in debugfs
clk: qcom: gcc-msm8996: Disable halt check on UFS tx clock
clk: meson: audio-divider is one based
clk: meson-gxbb: set fclk_div2 as CLK_IS_CRITICAL
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull fscache/cachefiles fixes from David Howells:
- Allow cancelled operations to be queued so they can be cleaned up.
- Fix a refcounting bug in the monitoring of reads on backend files
whereby a race can occur between monitor objects being listed for
work, the work processing being queued and the work processor running
and destroying the monitor objects.
- Fix a ref overput in object attachment, whereby a tentatively
considered object is put in error handling without first being 'got'.
- Fix a missing clear of the CACHEFILES_OBJECT_ACTIVE flag whereby an
assertion occurs when we retry because it seems the object is now
active.
- Wait rather BUG'ing on an object collision in the depths of
cachefiles as the active object should be being cleaned up - also
depends on the one above.
* tag 'fscache-fixes-20180725' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
cachefiles: Wait rather than BUG'ing on "Unexpected object collision"
cachefiles: Fix missing clear of the CACHEFILES_OBJECT_ACTIVE flag
fscache: Fix reference overput in fscache_attach_object() error handling
cachefiles: Fix refcounting bug in backing-file read monitoring
fscache: Allow cancelled operations to be enqueued
|