aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2017-08-10USB: Check for dropped connection before switching to full speedAlan Stern1-4/+6
Some buggy USB disk adapters disconnect and reconnect multiple times during the enumeration procedure. This may lead to a device connecting at full speed instead of high speed, because when the USB stack sees that a device isn't able to enumerate at high speed, it tries to hand the connection over to a full-speed companion controller. The logic for doing this is careful to check that the device is still connected. But this check is inadequate if the device disconnects and reconnects before the check is done. The symptom is that a device works, but much more slowly than it is capable of operating. The situation was made worse recently by commit 22547c4cc4fe ("usb: hub: Wait for connection to be reestablished after port reset"), which increases the delay following a reset before a disconnect is recognized, thus giving the device more time to reconnect. This patch makes the check more robust. If the device was disconnected at any time during enumeration, we will now skip the full-speed handover. Signed-off-by: Alan Stern <[email protected]> Reported-and-tested-by: Zdenek Kabelac <[email protected]> Reviewed-by: Guenter Roeck <[email protected]> Cc: stable <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2017-08-10usb:xhci:Add quirk for Certain failing HP keyboard on reset after resumeSandeep Singh2-5/+13
Certain HP keyboards would keep inputting a character automatically which is the wake-up key after S3 resume On some AMD platforms USB host fails to respond (by holding resume-K) to USB device (an HP keyboard) resume request within 1ms (TURSM) and ensures that resume is signaled for at least 20 ms (TDRSMDN), which is defined in USB 2.0 spec. The result is that the keyboard is out of function. In SNPS USB design, the host responds to the resume request only after system gets back to S0 and the host gets to functional after the internal HW restore operation that is more than 1 second after the initial resume request from the USB device. As a workaround for specific keyboard ID(HP Keyboards), applying port reset after resume when the keyboard is plugged in. Signed-off-by: Sandeep Singh <[email protected]> Signed-off-by: Shyam Sundar S K <[email protected]> cc: Nehal Shah <[email protected]> Reviewed-by: Felipe Balbi <[email protected]> Cc: stable <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2017-08-03Merge tag 'usb-serial-4.13-rc4' of ↵Greg Kroah-Hartman2-0/+3
git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus Johan writes: USB-serial fixes for v4.13-rc4 Here are some new device ids for v4.13-rc4. All have been in linux-next with no reported issues. Signed-off-by: Johan Hovold <[email protected]>
2017-08-03Merge tag 'fixes-for-v4.13-rc4' of ↵Greg Kroah-Hartman228-1526/+1973
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus Felipe writes: usb: fixes for v4.13-rc4 Another fix for isochronous transfers on dwc3. This time around, we're making sure that we use correct PIDs in all transfer sizes. MSM PHY driver got a fix for the use of devm_regulator_bulk_get() API which will avoid kernel crashes. Renesas DRD driver got 3 fixes: a fix on giveback, a fix for proper controller programming and the removal of set-but-never-used variable.
2017-08-03usb: renesas_usbhs: gadget: fix unused-but-set-variable warningYoshihiro Shimoda1-4/+1
The commit b8b9c974afee ("usb: renesas_usbhs: gadget: disable all eps when the driver stops") causes the unused-but-set-variable warning. But, if the usbhsg_ep_disable() will return non-zero value, udc/core.c doesn't clear the ep->enabled flag. So, this driver should not return non-zero value, if the pipe is zero because this means the pipe is already disabled. Otherwise, the ep->enabled flag is never cleared when the usbhsg_ep_disable() is called by the renesas_usbhs driver first. Fixes: b8b9c974afee ("usb: renesas_usbhs: gadget: disable all eps when the driver stops") Fixes: 11432050f070 ("usb: renesas_usbhs: gadget: fix NULL pointer dereference in ep_disable()") Signed-off-by: Yoshihiro Shimoda <[email protected]> Signed-off-by: Felipe Balbi <[email protected]>
2017-08-03usb: renesas_usbhs: Fix UGCTRL2 value for R-Car Gen3Yoshihiro Shimoda1-2/+7
The latest HW manual (Rev.0.55) shows us this UGCTRL2.VBUSSEL bit. If the bit sets to 1, the VBUS drive is controlled by phy related registers (called "UCOM Registers" on the manual). Since R-Car Gen3 environment will control VBUS by phy-rcar-gen3-usb2 driver, the UGCTRL2.VBUSSEL bit should be set to 1. So, this patch fixes the register's value. Otherwise, even if the ID pin indicates to peripheral, the R-Car will output USBn_PWEN to 1 when a host driver is running. Fixes: de18757e272d ("usb: renesas_usbhs: add R-Car Gen3 power control" Cc: <[email protected]> # v4.6+ Signed-off-by: Yoshihiro Shimoda <[email protected]> Signed-off-by: Felipe Balbi <[email protected]>
2017-08-03usb: phy: phy-msm-usb: Fix usage of devm_regulator_bulk_get()Rajendra Nayak1-8/+9
The regulator_bulk_data pointer passed to devm_regulator_bulk_get() is used to store the client handles for the regulators, which is later used by devm_regulator_bulk_release() to free the regulators. Passing a local array as is done here means the memory used to store the handles is freed causing the handles to be corrupted, resulting in a crash when devm_regulator_bulk_release() tries to free them. Fix this my moving the array inside of the msm_otg structure. Signed-off-by: Rajendra Nayak <[email protected]> Signed-off-by: Felipe Balbi <[email protected]>
2017-08-03usb: gadget: udc: renesas_usb3: Fix usb_gadget_giveback_request() callingYoshihiro Shimoda1-5/+16
According to the gadget.h, a "complete" function will always be called with interrupts disabled. However, sometimes usb3_request_done() function is called with interrupts enabled. So, this function should be held by spin_lock_irqsave() to disable interruption. Also, this driver has to call spin_unlock() to avoid spinlock recursion by this driver before calling usb_gadget_giveback_request(). Reported-by: Kazuya Mizuguchi <[email protected]> Tested-by: Kazuya Mizuguchi <[email protected]> Fixes: 746bfe63bba3 ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller") Cc: <[email protected]> # v4.5+ Signed-off-by: Yoshihiro Shimoda <[email protected]> Signed-off-by: Felipe Balbi <[email protected]>
2017-08-03usb: dwc3: gadget: Correct ISOC DATA PIDs for short packetsManu Gautam1-1/+32
The PIDs for Isochronous data transfers are incorrect for high bandwidth IN endpoints when the request length is less than EP wMaxPacketSize. As per spec correct PIDs for ISOC data transfers are: 1) For request length <= maxpacket - DATA0, 2) For maxpacket < length <= (2 * maxpacket) - DATA1, DATA0 3) For (2 * maxpacket) < length <= (3 * maxpacket) - DATA2, DATA1, DATA0. But driver always sets PCM fields based on wMaxPacketSize due to which DATA2 happens even for small requests. Fix this by setting the PCM field of trb->size depending on request length rather than fixing it to the value depending on wMaxPacketSize. Ideally it shouldn't give any issues as dwc3 will send 0-length packet for next IN token if host sends (even after receiving a short packet). Windows seems to ignore this but with MacOS frame loss observed when using f_uvc. Signed-off-by: Manu Gautam <[email protected]> Signed-off-by: Felipe Balbi <[email protected]>
2017-08-01USB: serial: option: add D-Link DWM-222 device IDHector Martin1-0/+2
Add device id for D-Link DWM-222. Cc: [email protected] Signed-off-by: Hector Martin <[email protected]> Signed-off-by: Johan Hovold <[email protected]>
2017-07-30Linux 4.13-rc3Linus Torvalds1-1/+1
2017-07-30Merge branch 'x86-urgent-for-linus' of ↵Linus Torvalds3-3/+13
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull x86 fixes from Thomas Gleixner: "A small set of x86 fixes: - prevent the kernel from using the EFI reboot method when EFI is disabled. - two patches addressing clang issues" * 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/boot: Disable the address-of-packed-member compiler warning x86/efi: Fix reboot_mode when EFI runtime services are disabled x86/boot: #undef memcpy() et al in string.c
2017-07-30Merge branch 'sched-urgent-for-linus' of ↵Linus Torvalds2-5/+5
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull scheduler fixes from Thomas Gleixner: "Two patches addressing build warnings caused by inconsistent kernel doc comments" * 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: sched/wait: Clean up some documentation warnings sched/core: Fix some documentation build warnings
2017-07-30Merge branch 'perf-urgent-for-linus' of ↵Linus Torvalds2-11/+50
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull perf fixes from Thomas Gleixner: "A couple of fixes for performance counters and kprobes: - a series of small patches which make the uncore performance counters on Skylake server systems work correctly - add a missing instruction slot release to the failure path of kprobes" * 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: kprobes/x86: Release insn_slot in failure path perf/x86/intel/uncore: Fix missing marker for skx_uncore_cha_extra_regs perf/x86/intel/uncore: Fix SKX CHA event extra regs perf/x86/intel/uncore: Remove invalid Skylake server CHA filter field perf/x86/intel/uncore: Fix Skylake server CHA LLC_LOOKUP event umask perf/x86/intel/uncore: Fix Skylake server PCU PMU event format perf/x86/intel/uncore: Fix Skylake UPI PMU event masks
2017-07-30Merge branch 'irq-urgent-for-linus' of ↵Linus Torvalds2-3/+13
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull irq fix from Thomas Gleixner: "Fix for a regression caused by the conversion of x86 to the generic hotplug code. Instead of doing a plain single line revert, this adds a pile of comments so the semantics of the force argument are clear" * 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: genirq/cpuhotplug: Revert "Set force affinity flag on hotplug migration"
2017-07-30usb: musb: fix tx fifo flush handling againBin Liu1-0/+1
commit 68fe05e2a451 ("usb: musb: fix tx fifo flush handling") drops the 1ms delay trying to solve the long disconnect time issue when application queued many tx urbs. However, the 1ms delay is needed for some use cases, for example, without the delay, reconnecting AR9271 WIFI dongle no longer works if the connection is dropped from the AP. So let's add back the 1ms delay in musb_h_tx_flush_fifo(), and solve the long disconnect time problem with a separate patch for usb_hcd_flush_endpoint(). Cc: [email protected] # v4.4+ Signed-off-by: Bin Liu <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2017-07-30usb: core: unlink urbs from the tail of the endpoint's urb_listBin Liu1-1/+1
While unlink an urb, if the urb has been programmed in the controller, the controller driver might do some hw related actions to tear down the urb. Currently usb_hcd_flush_endpoint() passes each urb from the head of the endpoint's urb_list to the controller driver, which could make the controller driver think each urb has been programmed and take the unnecessary actions for each urb. This patch changes the behavior in usb_hcd_flush_endpoint() to pass the urbs from the tail of the list, to avoid any unnecessary actions in an controller driver. Cc: [email protected] # v4.4+ Acked-by: Alan Stern <[email protected]> Signed-off-by: Bin Liu <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2017-07-30usb-storage: fix deadlock involving host lock and scsi_doneAlan Stern1-6/+12
Christoph Hellwig says that since version 4.12, the kernel switched to using blk-mq by default. The old code used a softirq for handling request completions, but blk-mq can handle completions in the caller's context. This may cause a problem for usb-storage, because it invokes the ->scsi_done callback while holding the host lock, and the completion routine sometimes tries to acquire the same lock (when running the error handler, for example). The consequence is that the existing code will sometimes deadlock upon error completion of a SCSI command (with a lockdep warning). This is easy enough to fix, since usb-storage doesn't really need to hold the host lock while the callback runs. It was simpler to write it that way, but moving the call outside the locked region is pretty easy and there's no downside. That's what this patch does. Signed-off-by: Alan Stern <[email protected]> Reported-and-tested-by: Arthur Marsh <[email protected]> CC: Christoph Hellwig <[email protected]> CC: <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2017-07-30uas: Add US_FL_IGNORE_RESIDUE for Initio Corporation INIC-3069Alan Swanson1-2/+2
Similar to commit d595259fbb7a ("usb-storage: Add ignore-residue quirk for Initio INIC-3619") for INIC-3169 in unusual_devs.h but INIC-3069 already present in unusual_uas.h. Both in same controller IC family. Issue is that MakeMKV fails during key exchange with installed bluray drive with following error: 002004:0000 Error 'Scsi error - ILLEGAL REQUEST:COPY PROTECTION KEY EXCHANGE FAILURE - KEY NOT ESTABLISHED' occurred while issuing SCSI command AD010..080002400 to device 'SG:dev_11:0' Signed-off-by: Alan Swanson <[email protected]> Acked-by: Oliver Neukum <[email protected]> Cc: stable <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2017-07-30USB: hcd: Mark secondary HCD as dead if the primary one diedRafael J. Wysocki1-0/+2
Make usb_hc_died() clear the HCD_FLAG_RH_RUNNING flag for the shared HCD and set HCD_FLAG_DEAD for it, in analogy with what is done for the primary one. Among other thigs, this prevents check_root_hub_suspended() from returning -EBUSY for dead HCDs which helps to work around system suspend issues in some situations. This actually fixes occasional suspend failures on one of my test machines. Suggested-by: Alan Stern <[email protected]> Signed-off-by: Rafael J. Wysocki <[email protected]> Acked-by: Alan Stern <[email protected]> Cc: stable <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2017-07-28Merge tag 'devicetree-fixes-for-4.13' of ↵Linus Torvalds2-2/+2
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux Pull DeviceTree fixes from Rob Herring: "Two small DT fixes: - Fix error handling in of_irq_to_resource_table() due to of_irq_to_resource() error return changes. - Fix dtx_diff script due to dts include path changes" * tag 'devicetree-fixes-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: of: irq: fix of_irq_to_resource() error check scripts/dtc: dtx_diff - update include dts paths to match build
2017-07-28Merge tag 'nfs-for-4.13-3' of git://git.linux-nfs.org/projects/anna/linux-nfsLinus Torvalds2-6/+12
Pull NFS client fixes from Anna Schumaker: "More NFS client bugfixes for 4.13. Most of these fix locking bugs that Ben and Neil noticed, but I also have a patch to fix one more access bug that was reported after last week. Stable fixes: - Fix a race where CB_NOTIFY_LOCK fails to wake a waiter - Invalidate file size when taking a lock to prevent corruption Other fixes: - Don't excessively generate tiny writes with fallocate - Use the raw NFS access mask in nfs4_opendata_access()" * tag 'nfs-for-4.13-3' of git://git.linux-nfs.org/projects/anna/linux-nfs: NFSv4.1: Fix a race where CB_NOTIFY_LOCK fails to wake a waiter NFS: Optimize fallocate by refreshing mapping when needed. NFS: invalidate file size when taking a lock. NFS: Use raw NFS access mask in nfs4_opendata_access()
2017-07-28Merge tag 'xfs-4.13-fixes-2' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linuxLinus Torvalds6-3/+39
Pull xfs fixes from Darrick Wong: - fix firstfsb variables that we left uninitialized, which could lead to locking problems. - check for NULL metadata buffer pointers before using them. - don't allow btree cursor manipulation if the btree block is corrupt. Better to just shut down. - fix infinite loop problems in quotacheck. - fix buffer overrun when validating directory blocks. - fix deadlock problem in bunmapi. * tag 'xfs-4.13-fixes-2' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux: xfs: fix multi-AG deadlock in xfs_bunmapi xfs: check that dir block entries don't off the end of the buffer xfs: fix quotacheck dquot id overflow infinite loop xfs: check _alloc_read_agf buffer pointer before using xfs: set firstfsb to NULLFSBLOCK before feeding it to _bmapi_write xfs: check _btree_check_block value
2017-07-28Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvmLinus Torvalds16-49/+99
Pull KVM fixes from Paolo Bonzini: "s390: - SRCU fix PPC: - host crash fixes x86: - bugfixes, including making nested posted interrupts really work Generic: - tweaks to kvm_stat and to uevents" * tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: KVM: LAPIC: Fix reentrancy issues with preempt notifiers tools/kvm_stat: add '-f help' to get the available event list tools/kvm_stat: use variables instead of hard paths in help output KVM: nVMX: Fix loss of L2's NMI blocking state KVM: nVMX: Fix posted intr delivery when vcpu is in guest mode x86: irq: Define a global vector for nested posted interrupts KVM: x86: do mask out upper bits of PAE CR3 KVM: make pid available for uevents without debugfs KVM: s390: take srcu lock when getting/setting storage keys KVM: VMX: remove unused field KVM: PPC: Book3S HV: Fix host crash on changing HPT size KVM: PPC: Book3S HV: Enable TM before accessing TM registers
2017-07-28Merge tag 'for-linus-4.13b-rc3-tag' of ↵Linus Torvalds3-13/+5
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip Pull xen fixes from Juergen Gross: "Three minor cleanups for xen related drivers" * tag 'for-linus-4.13b-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: xen: dont fiddle with event channel masking in suspend/resume xen: selfballoon: remove unnecessary static in frontswap_selfshrink() xen: Drop un-informative message during boot
2017-07-28Merge tag 'arm64-fixes' of ↵Linus Torvalds15-61/+84
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux Pull arm64 fixes from Will Deacon: "I'd been collecting these whilst we debugged a CPU hotplug failure, but we ended up diagnosing that one to tglx, who has taken a fix via the -tip tree separately. We're seeing some NFS issues that we haven't gotten to the bottom of yet, and we've uncovered some issues with our backtracing too so there might be another fixes pull before we're done. Summary: - Ensure we have a guard page after the kernel image in vmalloc - Fix incorrect prefetch stride in copy_page - Ensure irqs are disabled in die() - Fix for event group validation in QCOM L2 PMU driver - Fix requesting of PMU IRQs on AMD Seattle - Minor cleanups and fixes" * tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: arm64: mmu: Place guard page after mapping of kernel image drivers/perf: arm_pmu: Request PMU SPIs with IRQF_PER_CPU arm64: sysreg: Fix unprotected macro argmuent in write_sysreg perf: qcom_l2: fix column exclusion check arm64/lib: copy_page: use consistent prefetch stride arm64/numa: Drop duplicate message perf: Convert to using %pOF instead of full_name arm64: Convert to using %pOF instead of full_name arm64: traps: disable irq in die() arm64: atomics: Remove '&' from '+&' asm constraint in lse atomics arm64: uaccess: Remove redundant __force from addr cast in __range_ok
2017-07-28Merge tag 'powerpc-4.13-4' of ↵Linus Torvalds9-36/+168
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux Pull powerpc fixes from Michael Ellerman: "The highlight is Ben's patch to work around a host killing bug when running KVM guests with the Radix MMU on Power9. See the long change log of that commit for more detail. And then three fairly minor fixes: - fix of_node_put() underflow during reconfig remove, using old DLPAR tools. - fix recently introduced ld version check with 64-bit LE-only toolchain. - free the subpage_prot_table correctly, avoiding a memory leak. Thanks to: Aneesh Kumar K.V, Benjamin Herrenschmidt, Laurent Vivier" * tag 'powerpc-4.13-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: powerpc/mm/hash: Free the subpage_prot_table correctly powerpc/Makefile: Fix ld version check with 64-bit LE-only toolchain powerpc/pseries: Fix of_node_put() underflow during reconfig remove powerpc/mm/radix: Workaround prefetch issue with KVM
2017-07-28NFSv4.1: Fix a race where CB_NOTIFY_LOCK fails to wake a waiterBenjamin Coddington1-1/+1
nfs4_retry_setlk() sets the task's state to TASK_INTERRUPTIBLE within the same region protected by the wait_queue's lock after checking for a notification from CB_NOTIFY_LOCK callback. However, after releasing that lock, a wakeup for that task may race in before the call to freezable_schedule_timeout_interruptible() and set TASK_WAKING, then freezable_schedule_timeout_interruptible() will set the state back to TASK_INTERRUPTIBLE before the task will sleep. The result is that the task will sleep for the entire duration of the timeout. Since we've already set TASK_INTERRUPTIBLE in the locked section, just use freezable_schedule_timout() instead. Fixes: a1d617d8f134 ("nfs: allow blocking locks to be awoken by lock callbacks") Signed-off-by: Benjamin Coddington <[email protected]> Reviewed-by: Jeff Layton <[email protected]> Cc: [email protected] # v4.9+ Signed-off-by: Anna Schumaker <[email protected]>
2017-07-28Merge branch 'linus' of ↵Linus Torvalds6-8/+10
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6 Pull crypto fixes from Herbert Xu: - remove broken dt bindings in inside-secure - fix authencesn crash when used with digest_null - fix cavium/nitrox firmware path - fix SHA3 failure in brcm - fix Kconfig dependency for brcm * 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: crypto: authencesn - Fix digest_null crash crypto: brcm - remove BCM_PDC_MBOX dependency in Kconfig Documentation/bindings: crypto: remove the dma-mask property crypto: inside-secure - do not parse the dma mask from dt crypto: cavium/nitrox - Change in firmware path. crypto: brcm - Fix SHA3-512 algorithm failure
2017-07-28Merge branch 'for-4.13-part3' of ↵Linus Torvalds3-10/+8
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux Pull btrfs fixes from David Sterba: "Fixes addressing problems reported by users, and there's one more regression fix" * 'for-4.13-part3' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux: btrfs: round down size diff when shrinking/growing device Btrfs: fix early ENOSPC due to delalloc btrfs: fix lockup in find_free_extent with read-only block groups Btrfs: fix dir item validation when replaying xattr deletes
2017-07-28Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/mdLinus Torvalds6-126/+115
Pull MD fixes from Shaohua Li: "This fixes several bugs, three of them are marked for stable: - an initialization issue fixed by Ming - a bio clone race issue fixed by me - an async tx flush issue fixed by Ofer - other cleanups" * 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md: MD: fix warnning for UP case md/raid5: add thread_group worker async_tx_issue_pending_all md: simplify code with bio_io_error md/raid1: fix writebehind bio clone md: raid1-10: move raid1/raid10 common code into raid1-10.c md: raid1/raid10: initialize bvec table via bio_add_page() md: remove 'idx' from 'struct resync_pages'
2017-07-28Merge tag 'for-4.13/dm-fixes' of ↵Linus Torvalds11-46/+94
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm Pull device mapper fixes from Mike Snitzer: - a few DM integrity fixes that improve performance. One that address inefficiencies in the on-disk journal device layout. Another that makes use of the block layer's on-stack plugging when writing the journal. - a dm-bufio fix for the blk_status_t conversion that went in during the merge window. - a few DM raid fixes that address correctness when suspending the device and a validation fix for validation that occurs during device activation. - a couple DM zoned target fixes. Important one being the fix to not use GFP_KERNEL in the IO path due to concerns about deadlock in low-memory conditions (e.g. swap over a DM zoned device, etc). - a DM DAX device fix to make sure dm_dax_flush() is called if the underlying DAX device is operating as a write cache. * tag 'for-4.13/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm: dm, dax: Make sure dm_dax_flush() is called if device supports it dm verity fec: fix GFP flags used with mempool_alloc() dm zoned: use GFP_NOIO in I/O path dm zoned: remove test for impossible REQ_OP_FLUSH conditions dm raid: bump target version dm raid: avoid mddev->suspended access dm raid: fix activation check in validate_raid_redundancy() dm raid: remove WARN_ON() in raid10_md_layout_to_format() dm bufio: fix error code in dm_bufio_write_dirty_buffers() dm integrity: test for corrupted disk format during table load dm integrity: WARN_ON if variables representing journal usage get out of sync dm integrity: use plugging when writing the journal dm integrity: fix inefficient allocation of journal space
2017-07-28Merge branch 'for-linus' of git://git.kernel.dk/linux-blockLinus Torvalds13-138/+197
Pull block fixes from Jens Axboe: "A small collection of fixes that should go into this series. This contains: - NVMe pull request from Christoph, with various fixes for nvme proper and nvme-fc. - disable runtime PM for blk-mq for now. With scsi now defaulting to using blk-mq, this reared its head as an issue. Longer term we'll fix up runtime PM for blk-mq, for now just disable it to prevent a hang on laptop resume for some folks. - blk-mq CPU <-> hw queue map fix from Christoph. - xen/blkfront pull request from Konrad, with two small fixes for the blkfront driver. - a few fixups for nbd from Joseph. - a stable fix for pblk from Javier" * 'for-linus' of git://git.kernel.dk/linux-block: lightnvm: pblk: advance bio according to lba index nvme: validate admin queue before unquiesce nbd: clear disconnected on reconnect nvme-pci: fix HMB size calculation nvme-fc: revise TRADDR parsing nvme-fc: address target disconnect race conditions in fcp io submit nvme: fabrics commands should use the fctype field for data direction nvme: also provide a UUID in the WWID sysfs attribute xen/blkfront: always allocate grants first from per-queue persistent grants xen-blkfront: fix mq start/stop race blk-mq: map queues to all present CPUs block: disable runtime-pm for blk-mq xen-blkfront: Fix handling of non-supported operations nbd: only set sndtimeo if we have a timeout set nbd: take tx_lock before disconnecting nbd: allow multiple disconnects to be sent
2017-07-28Merge tag 'mmc-v4.13-rc1' of ↵Linus Torvalds11-284/+16
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc Pull MMC fixes from Ulf Hansson: "Here are a couple of mmc fixes intended for v4.13-rc1. I have also included a couple of cleanup patches in this pull request for OMAP2+, related to the omap_hsmmc driver. The reason is because of the changes are also depending on OMAP SoC specific code, so this simplifies how to deal with this. Summary: MMC host: - sunxi: Correct time phase settings - omap_hsmmc: Clean up some dead code - dw_mmc: Fix message printed for deprecated num-slots DT binding - dw_mmc: Fix DT documentation" * tag 'mmc-v4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: Documentation: dw-mshc: deprecate num-slots mmc: dw_mmc: fix the wrong condition check of getting num-slots from DT mmc: host: omap_hsmmc: remove unused platform callbacks ARM: OMAP2+: hsmmc.c: Remove dead code mmc: sunxi: Keep default timing phase settings for new timing mode
2017-07-28lightnvm: pblk: advance bio according to lba indexJavier González3-10/+19
When a lba either hits the cache or corresponds to an empty entry in the L2P table, we need to advance the bio according to the position in which the lba is located. Otherwise, we will copy data in the wrong page, thus causing data corruption for the application. In case of a cache hit, we assumed that bio->bi_iter.bi_idx would contain the correct index, but this is no necessarily true. Instead, use the local bio advance counter and iterator. This guarantees that lbas hitting the cache are copied into the right bv_page. In case of an empty L2P entry, we omitted to advance the bio. In the cases when the same I/O also contains a cache hit, data corresponding to this lba will be copied to the wrong bv_page. Fix this by advancing the bio as we do in the case of a cache hit. Fixes: a4bd217b4326 lightnvm: physical block device (pblk) target Signed-off-by: Javier González <[email protected]> Signed-off-by: Jens Axboe <[email protected]>
2017-07-28arm64: mmu: Place guard page after mapping of kernel imageWill Deacon1-7/+11
The vast majority of virtual allocations in the vmalloc region are followed by a guard page, which can help to avoid overruning on vma into another, which may map a read-sensitive device. This patch adds a guard page to the end of the kernel image mapping (i.e. following the data/bss segments). Cc: Mark Rutland <[email protected]> Reviewed-by: Ard Biesheuvel <[email protected]> Signed-off-by: Will Deacon <[email protected]>
2017-07-28x86/boot: Disable the address-of-packed-member compiler warningMatthias Kaehlcke1-0/+1
The clang warning 'address-of-packed-member' is disabled for the general kernel code, also disable it for the x86 boot code. This suppresses a bunch of warnings like this when building with clang: ./arch/x86/include/asm/processor.h:535:30: warning: taking address of packed member 'sp0' of class or structure 'x86_hw_tss' may result in an unaligned pointer value [-Waddress-of-packed-member] return this_cpu_read_stable(cpu_tss.x86_tss.sp0); ^~~~~~~~~~~~~~~~~~~ ./arch/x86/include/asm/percpu.h:391:59: note: expanded from macro 'this_cpu_read_stable' #define this_cpu_read_stable(var) percpu_stable_op("mov", var) ^~~ ./arch/x86/include/asm/percpu.h:228:16: note: expanded from macro 'percpu_stable_op' : "p" (&(var))); ^~~ Signed-off-by: Matthias Kaehlcke <[email protected]> Cc: Doug Anderson <[email protected]> Cc: Linus Torvalds <[email protected]> Cc: Masahiro Yamada <[email protected]> Cc: Peter Zijlstra <[email protected]> Cc: Thomas Gleixner <[email protected]> Link: http://lkml.kernel.org/r/[email protected] Signed-off-by: Ingo Molnar <[email protected]>
2017-07-27Merge tag 'drm-fixes-for-v4.13-rc3' of ↵Linus Torvalds51-229/+298
git://people.freedesktop.org/~airlied/linux Pull drm fixes from Dave Airlie: "These iare the fixes for 4.13-rc3: vmwgfx, exynos, i915, amdgpu, nouveau, host1x and displayport fixes. As expected people woke up this week, i915 didn't do an -rc2 pull so got a bumper -rc3 pull, and Ben resurfaced on nouveau and fixed a bunch of major crashers seen on Fedora 26, and there are a few vmwgfx fixes as well. Otherwise exynos had some regression fixes/cleanups, and amdgpu has an rcu locking regression fix and a couple of minor fixes" * tag 'drm-fixes-for-v4.13-rc3' of git://people.freedesktop.org/~airlied/linux: (44 commits) drm/i915: Fix bad comparison in skl_compute_plane_wm. drm/i915: Force CPU synchronisation even if userspace requests ASYNC drm/i915: Only skip updating execobject.offset after error drm/i915: Only mark the execobject as pinned on success drm/i915: Remove assertion from raw __i915_vma_unpin() drm/i915/cnl: Fix loadgen select programming on ddi vswing sequence drm/i915: Fix scaler init during CRTC HW state readout drm/i915/selftests: Fix an error handling path in 'mock_gem_device()' drm/i915: Unbreak gpu reset vs. modeset locking gpu: host1x: Free the IOMMU domain when there is no device to attach drm/i915: Fix cursor updates on some platforms drm/i915: Fix user ptr check size in eb_relocate_vma() drm: exynos: mark pm functions as __maybe_unused drm/exynos: select CEC_CORE if CEC_NOTIFIER drm/exynos/hdmi: fix disable sequence drm/exynos: mic: add a bridge at probe drm/exynos/dsi: Remove error handling for bridge_node DT parsing drm/exynos: dsi: do not try to find bridge drm: exynos: hdmi: make of_device_ids const. drm: exynos: constify mixer_match_types and *_mxr_drv_data. ...
2017-07-28Merge tag 'exynos-drm-fixes-for-v4.13-rc3' of ↵Dave Airlie6-27/+29
git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-fixes Summary: - fix probing fail issue of dsi driver without bridge device. - fix disable sequence of hdmi driver. - trivial cleanups. * tag 'exynos-drm-fixes-for-v4.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos: drm: exynos: mark pm functions as __maybe_unused drm/exynos: select CEC_CORE if CEC_NOTIFIER drm/exynos/hdmi: fix disable sequence drm/exynos: mic: add a bridge at probe drm/exynos/dsi: Remove error handling for bridge_node DT parsing drm/exynos: dsi: do not try to find bridge drm: exynos: hdmi: make of_device_ids const. drm: exynos: constify mixer_match_types and *_mxr_drv_data. exynos_drm: Clean up duplicated assignment in exynos_drm_driver
2017-07-28Merge tag 'drm-intel-fixes-2017-07-27' of ↵Dave Airlie10-83/+72
git://anongit.freedesktop.org/git/drm-intel into drm-fixes i915 fixes for -rc3 Bit more than usual since we missed -rc2. 4x cc: stable, 2 gvt patches, but all fairly minor stuff. Last minute rebase was to add a few missing cc: stable, I did prep the pull this morning already and made sure CI approves. * tag 'drm-intel-fixes-2017-07-27' of git://anongit.freedesktop.org/git/drm-intel: drm/i915: Fix bad comparison in skl_compute_plane_wm. drm/i915: Force CPU synchronisation even if userspace requests ASYNC drm/i915: Only skip updating execobject.offset after error drm/i915: Only mark the execobject as pinned on success drm/i915: Remove assertion from raw __i915_vma_unpin() drm/i915/cnl: Fix loadgen select programming on ddi vswing sequence drm/i915: Fix scaler init during CRTC HW state readout drm/i915/selftests: Fix an error handling path in 'mock_gem_device()' drm/i915: Unbreak gpu reset vs. modeset locking drm/i915: Fix cursor updates on some platforms drm/i915: Fix user ptr check size in eb_relocate_vma() drm/i915/gvt: Extend KBL platform support in GVT-g drm/i915/gvt: Fix the vblank timer close issue after shutdown VMs in reverse
2017-07-28Merge tag 'drm-misc-fixes-2017-07-27' of ↵Dave Airlie3-13/+19
git://anongit.freedesktop.org/git/drm-misc into drm-fixes Core Changes: - dp: A few fixes in drm_dp_downstream_debug() (Chris) - rockchip: sanitize the Kconfig dependencies (fallout from EXTCON) (Arnd) - host1x: Free the iommu domain when attach_device fails (Paul) Cc: Chris Wilson <[email protected]> Cc: Arnd Bergmann <[email protected]> Cc: Paul Kocialkowski <[email protected]> * tag 'drm-misc-fixes-2017-07-27' of git://anongit.freedesktop.org/git/drm-misc: gpu: host1x: Free the IOMMU domain when there is no device to attach drm/rockchip: fix Kconfig dependencies drm/dp: Don't trust drm_dp_downstream_id() drm/dp: Fix read pointer for drm_dp_downsteam_debug()
2017-07-27Merge tag 'acpi-4.13-rc3' of ↵Linus Torvalds5-4/+48
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm Pull ACPI fixes from Rafael Wysocki: "These are two fixups for the suspend-to-idle handling in the ACPI subsystem after recent changes in that area and two simple fixes of the ACPI NUMA code. Specifics: - Add an ACPI module parameter to allow users to override the new default behavior on some systems where the EC GPE is not disabled during suspend-to-idle in case the EC on their systems generates excessive wakeup events and they want to sacrifice some functionality (like power button wakeups) for extra battery life while suspended (Rafael Wysocki). - Fix flushing of the outstanding EC work in the ACPI core suspend-to-idle code (Rafael Wysocki). - Add a missing include and fix a messed-up comment in the ACPI NUMA code (Ross Zwisler)" * tag 'acpi-4.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: ACPI: NUMA: Fix typo in the full name of SRAT ACPI: NUMA: add missing include in acpi_numa.h ACPI / PM / EC: Flush all EC work in acpi_freeze_sync() ACPI / EC: Add parameter to force disable the GPE on suspend
2017-07-27Merge branches 'acpi-pm' and 'acpi-numa'Rafael J. Wysocki452-4379/+11725
* acpi-pm: ACPI / PM / EC: Flush all EC work in acpi_freeze_sync() ACPI / EC: Add parameter to force disable the GPE on suspend * acpi-numa: ACPI: NUMA: Fix typo in the full name of SRAT ACPI: NUMA: add missing include in acpi_numa.h
2017-07-27Merge tag 'gvt-fixes-2017-07-26' of https://github.com/01org/gvt-linux into ↵Daniel Vetter2-12/+12
drm-intel-fixes gvt-fixes-2017-07-26 - Turn on KBL support for more SKUs (Jianjun) - Fix vblank timer close bug (Fred) Signed-off-by: Daniel Vetter <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
2017-07-27drm/i915: Fix bad comparison in skl_compute_plane_wm.Maarten Lankhorst1-2/+2
ddb_allocation && ddb_allocation / blocks_per_line >= 1 is the same as ddb_allocation >= blocks_per_line, so use the latter to simplify this. This fixes the following compiler warning: drivers/gpu/drm/i915/intel_pm.c:4467]: (warning) Comparison of a boolean expression with an integer other than 0 or 1. Signed-off-by: Maarten Lankhorst <[email protected]> Fixes: d555cb5827d6 ("drm/i915/skl+: use linetime latency if ddb size is not available") Cc: "Mahesh Kumar" <[email protected]> Reported-by: David Binderman <[email protected]> Cc: David Binderman <[email protected]> Cc: <[email protected]> # v4.13-rc1+ Reviewed-by: Mahesh Kumar <[email protected]> (cherry picked from commit 54d20ed1fff23c7d2633f01fc788111bf9c51c5d) Signed-off-by: Jani Nikula <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/[email protected] Signed-off-by: Daniel Vetter <[email protected]>
2017-07-27drm/i915: Force CPU synchronisation even if userspace requests ASYNCChris Wilson3-8/+11
The goal here was to minimise doing any thing or any check inside the kernel that was not strictly required. For a userspace that assumes complete control over the cache domains, the kernel is usually using outdated information and may trigger clflushes where none were required. However, swapping is a situation where userspace has no knowledge of the domain transfer, and will leave the object in the CPU cache. The kernel must flush this out to the backing storage prior to use with the GPU. As we use an asynchronous task tracked by an implicit fence for this, we also need to cancel the ASYNC flag on the object so that the object will wait for the clflush to complete before being executed. This also absolves userspace of the responsibility imposed by commit 77ae9957897d ("drm/i915: Enable userspace to opt-out of implicit fencing") that its needed to ensure that the object was out of the CPU cache prior to use on the GPU. Fixes: 77ae9957897d ("drm/i915: Enable userspace to opt-out of implicit fencing") Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101571 Signed-off-by: Chris Wilson <[email protected]> Cc: Joonas Lahtinen <[email protected]> Cc: Jason Ekstrand <[email protected]> Reviewed-by: Jason Ekstrand <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/[email protected] Reviewed-by: Joonas Lahtinen <[email protected]> Signed-off-by: Daniel Vetter <[email protected]> (cherry picked from commit 0f46daa1a273779a0b73d768a788ca3f04238f9c) Cc: [email protected] Signed-off-by: Daniel Vetter <[email protected]>
2017-07-27drm/i915: Only skip updating execobject.offset after errorChris Wilson1-3/+3
I was being overly paranoid in not updating the execobject.offset after performing the fallback copy where we set reloc.presumed_offset to -1. The thinking was to ensure that a subsequent NORELOC execbuf would be forced to process the invalid relocations. However this is overkill so long as we *only* update the execobject.offset following a successful update of the relocation value witin the batch. If we have to repeat the execbuf due to a later interruption, then we may skip the relocations on the second pass (honouring NORELOC) since the execobject.offset match the actual offsets (even though reloc.presumed_offset is garbage). Subsequent calls to execbuf with NORELOC should themselves ensure that the reloc.presumed_offset have been corrected in case of future migration. Reporting back the actual execobject.offset, even when reloc.presumed_offset is garbage, ensures that reuse of those objects use the latest information to avoid relocations. Fixes: 2889caa92321 ("drm/i915: Eliminate lots of iterations over the execobjects array") Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101635 Signed-off-by: Chris Wilson <[email protected]> Cc: Joonas Lahtinen <[email protected]> Cc: Tvrtko Ursulin <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/[email protected] Reviewed-by: Joonas Lahtinen <[email protected]> Signed-off-by: Daniel Vetter <[email protected]> (cherry picked from commit 1f727d9e725a408ef58d159c20fb2e51818ff153) Signed-off-by: Daniel Vetter <[email protected]>
2017-07-27drm/i915: Only mark the execobject as pinned on successChris Wilson1-3/+3
If we fail to acquire a fence (for old school fenced GPU access) then we unwind the vma reservation, including its pin. However, we were making the execobject as holding the pin before erring out, leading to a double unpin: [ 3193.991802] kernel BUG at drivers/gpu/drm/i915/i915_vma.h:287! [ 3193.998131] invalid opcode: 0000 [#1] PREEMPT SMP [ 3194.002816] Modules linked in: snd_hda_intel i915 vgem snd_hda_codec_analog snd_hda_codec_generic coretemp snd_hda_codec snd_hwdep snd_hda_core snd_pcm lpc_ich mei_me e1000e mei prime_numbers ptp pps_core [last unloaded: i915] [ 3194.022841] CPU: 0 PID: 8123 Comm: kms_flip Tainted: G U 4.13.0-rc1-CI-CI_DRM_471+ #1 [ 3194.031765] Hardware name: Dell Inc. OptiPlex 755 /0PU052, BIOS A04 11/05/2007 [ 3194.040343] task: ffff8800785d4c40 task.stack: ffffc90001768000 [ 3194.046339] RIP: 0010:eb_release_vmas.isra.6+0x119/0x180 [i915] [ 3194.052234] RSP: 0018:ffffc9000176ba80 EFLAGS: 00010246 [ 3194.057439] RAX: 00000000000003c0 RBX: ffff8800710fc2d8 RCX: ffff8800588e4f48 [ 3194.064546] RDX: ffffffff1fffffff RSI: 00000000ffffffff RDI: ffff8800588e00d0 [ 3194.071654] RBP: ffffc9000176bab0 R08: 0000000000000000 R09: 0000000000000000 [ 3194.078761] R10: 0000000000000040 R11: 0000000000000001 R12: ffff880060822f00 [ 3194.085867] R13: 0000000000000310 R14: 00000000000003b8 R15: ffffc9000176bbb0 [ 3194.092975] FS: 00007fd2b94aba40(0000) GS:ffff88007d200000(0000) knlGS:0000000000000000 [ 3194.101033] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 3194.106754] CR2: 00007ffbec3ff000 CR3: 0000000074e67000 CR4: 00000000000006f0 [ 3194.113861] Call Trace: [ 3194.116321] eb_relocate_slow+0x67/0x4e0 [i915] [ 3194.120861] i915_gem_do_execbuffer+0x429/0x1260 [i915] [ 3194.126070] ? lock_acquire+0xb5/0x210 [ 3194.129803] ? __might_fault+0x39/0x90 [ 3194.133563] i915_gem_execbuffer2+0x9b/0x1b0 [i915] [ 3194.138447] ? i915_gem_execbuffer+0x2b0/0x2b0 [i915] [ 3194.143478] drm_ioctl_kernel+0x64/0xb0 [ 3194.147298] drm_ioctl+0x2cd/0x390 [ 3194.150710] ? i915_gem_execbuffer+0x2b0/0x2b0 [i915] [ 3194.155741] ? finish_task_switch+0xa5/0x210 [ 3194.159993] ? finish_task_switch+0x6a/0x210 [ 3194.164247] do_vfs_ioctl+0x90/0x670 [ 3194.167806] ? entry_SYSCALL_64_fastpath+0x5/0xb1 [ 3194.172492] ? __this_cpu_preempt_check+0x13/0x20 [ 3194.177176] ? trace_hardirqs_on_caller+0xe7/0x1c0 [ 3194.181946] SyS_ioctl+0x3c/0x70 [ 3194.185159] entry_SYSCALL_64_fastpath+0x1c/0xb1 [ 3194.189756] RIP: 0033:0x7fd2b76a8587 [ 3194.193314] RSP: 002b:00007fff074845b8 EFLAGS: 00000246 ORIG_RAX: 0000000000000010 [ 3194.200855] RAX: ffffffffffffffda RBX: ffffffff8146da43 RCX: 00007fd2b76a8587 [ 3194.207962] RDX: 00007fff074846e0 RSI: 0000000040406469 RDI: 0000000000000003 [ 3194.215068] RBP: ffffc9000176bf88 R08: 0000000000000000 R09: 0000000000000003 [ 3194.222175] R10: 00007fd2b796bb58 R11: 0000000000000246 R12: 00007fff07484880 [ 3194.229280] R13: 0000000000000003 R14: 0000000040406469 R15: 0000000000000000 [ 3194.236386] ? __this_cpu_preempt_check+0x13/0x20 [ 3194.241070] Code: 24 b0 00 00 00 48 85 c9 0f 84 6c ff ff ff 8b 41 20 85 c0 7e 73 83 e8 01 89 41 20 41 8b 84 24 e8 00 00 00 a8 0f 0f 85 5f ff ff ff <0f> 0b 48 83 c4 08 5b 41 5c 41 5d 41 5e 41 5f 5d f3 c3 49 8b 84 [ 3194.259943] RIP: eb_release_vmas.isra.6+0x119/0x180 [i915] RSP: ffffc9000176ba80 [ 3194.268047] ---[ end trace 1d7348c6575d8800 ]--- [ 3673.658819] softdog: Initiating panic [ 3673.662471] Kernel panic - not syncing: Software Watchdog Timer expired [ 3673.669066] Kernel Offset: disabled [ 3673.672541] Rebooting in 1 seconds.. Reported-by: Tomi Sarvela <[email protected]> Fixes: 2889caa92321 ("drm/i915: Eliminate lots of iterations over the execobjects array") Signed-off-by: Chris Wilson <[email protected]> Cc: Joonas Lahtinen <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/[email protected] Reviewed-by: Joonas Lahtinen <[email protected]> Signed-off-by: Daniel Vetter <[email protected]> (cherry picked from commit 1da7b54c46bcfe5484af0b27d8c9003b238031b0) Signed-off-by: Daniel Vetter <[email protected]>
2017-07-27drm/i915: Remove assertion from raw __i915_vma_unpin()Chris Wilson1-1/+1
After we detect a i915_vma pin overflow, we call __i915_vma_unpin to cleanup. However, on an overflow the pin_count bitfield will be zero, triggering an assertion, even though we the intention is to merely warn and report the error back to the user (as historically the culprit has be a leak in the display code). Fixes: 20dfbde463c8 ("drm/i915: Wrap vma->pin_count accessors with small inline helpers") Signed-off-by: Chris Wilson <[email protected]> Cc: Joonas Lahtinen <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/[email protected] Reviewed-by: Joonas Lahtinen <[email protected]> Signed-off-by: Daniel Vetter <[email protected]> (cherry picked from commit 67fddd902b8e37b15a905c287ce4e40f52a564af) Signed-off-by: Daniel Vetter <[email protected]>
2017-07-27drm/i915/cnl: Fix loadgen select programming on ddi vswing sequenceNavare, Manasi D1-2/+2
The condition for setting the Loadgen Select bit of PORT_TX_DW4 register during DDI Vswing Sequence should be Bit rate <=6 GHz whereas the existing code checks only Bit Rate < 6GHz. This patch fixes this condition. While at it also remove the redundant paranthesis. Fixes: cf54ca8bc567 ("drm/i915/cnl: Implement voltage swing sequence.") Cc: Paulo Zanoni <[email protected]> Cc: Rodrigo Vivi <[email protected]> Signed-off-by: Manasi Navare <[email protected]> Reviewed-by: Paulo Zanoni <[email protected]> Signed-off-by: Paulo Zanoni <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/[email protected] Signed-off-by: Daniel Vetter <[email protected]> (cherry picked from commit a8e45a1c42d11597e975f3e5f2fe182f90cdaa7f) Signed-off-by: Daniel Vetter <[email protected]>
Powered by cgit, Gruvboxed by Blaster4385.