| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The recent extension of irq_set_lockdep_class() with a second argument
added the new lockdep class to the mrcmstb driver, but used the already
existing lockdep class as second argument, which leaves the new lockdep
class defined but unused.
Use the new lockdep class as that's what the change intended to do.
Fixes: 39c3fd58952d ("kernel/irq: Extend lockdep class for request mutex")
Reported-by: Ingo Molnar <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Cc: Andrew Lunn <[email protected]>
Cc: [email protected]
|
|
Some of the APIC incarnations are operating in lowest priority delivery
mode. This worked as long as the vector management code allocated the same
vector on all possible CPUs for each interrupt.
Lowest priority delivery mode does not necessarily respect the affinity
setting and may redirect to some other online CPU. This was documented
somewhere in the old code and the conversion to single target delivery
missed to update the delivery mode of the affected APIC drivers which
results in spurious interrupts on some of the affected CPU/Chipset
combinations.
Switch the APIC drivers over to Fixed delivery mode and remove all
leftovers of lowest priority delivery mode.
Switching to Fixed delivery mode is not a problem on these CPUs because the
kernel already uses Fixed delivery mode for IPIs. The reason for this is
that th SDM explicitely forbids lowest prio mode for IPIs. The reason is
obvious: If the irq routing does not honor destination targets in lowest
prio mode then an IPI targeted at CPU1 might end up on CPU0, which would be
a fatal problem in many cases.
As a consequence of this change, the apic::irq_delivery_mode field is now
pointless, but this needs to be cleaned up in a separate patch.
Fixes: fdba46ffb4c2 ("x86/apic: Get rid of multi CPU affinity")
Reported-by: [email protected]
Signed-off-by: Thomas Gleixner <[email protected]>
Tested-by: [email protected]
Cc: Pavel Machek <[email protected]>
Link: https://lkml.kernel.org/r/alpine.DEB.2.20.1712281140440.1688@nanos
|
|
Pull networking fixes from David Miller:
1) IPv6 gre tunnels end up with different default features enabled
depending upon whether netlink or ioctls are used to bring them up.
Fix from Alexey Kodanev.
2) Fix read past end of user control message in RDS< from Avinash
Repaka.
3) Missing RCU barrier in mini qdisc code, from Cong Wang.
4) Missing policy put when reusing per-cpu route entries, from Florian
Westphal.
5) Handle nested PCI errors properly in bnx2x driver, from Guilherme G.
Piccoli.
6) Run nested transport mode IPSEC packets via tasklet, from Herbert
Xu.
7) Fix handling poll() for stream sockets in tipc, from Parthasarathy
Bhuvaragan.
8) Fix two stack-out-of-bounds issues in IPSEC, from Steffen Klassert.
9) Another zerocopy ubuf handling fix, from Willem de Bruijn.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (33 commits)
strparser: Call sock_owned_by_user_nocheck
sock: Add sock_owned_by_user_nocheck
skbuff: in skb_copy_ubufs unclone before releasing zerocopy
tipc: fix hanging poll() for stream sockets
sctp: Replace use of sockets_allocated with specified macro.
bnx2x: Improve reliability in case of nested PCI errors
tg3: Enable PHY reset in MTU change path for 5720
tg3: Add workaround to restrict 5762 MRRS to 2048
tg3: Update copyright
net: fec: unmap the xmit buffer that are not transferred by DMA
tipc: fix tipc_mon_delete() oops in tipc_enable_bearer() error path
tipc: error path leak fixes in tipc_enable_bearer()
RDS: Check cmsg_len before dereferencing CMSG_DATA
tcp: Avoid preprocessor directives in tracepoint macro args
tipc: fix memory leak of group member when peer node is lost
net: sched: fix possible null pointer deref in tcf_block_put
tipc: base group replicast ack counter on number of actual receivers
net_sched: fix a missing rcu barrier in mini_qdisc_pair_swap()
net: phy: micrel: ksz9031: reconfigure autoneg after phy autoneg workaround
ip6_gre: fix device features for ioctl setup
...
|
|
git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"nouveau and i915 regression fixes"
* tag 'drm-fixes-for-v4.15-rc6' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau: fix race when adding delayed work items
i915: Reject CCS modifiers for pipe C on Geminilake
drm/i915/gvt: Fix pipe A enable as default for vgpu
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fix from Stephen Boyd:
"One more fix for the runtime PM clk patches. We're calling a runtime
PM API that may schedule from somewhere that we can't do that. We
change to the async version of pm_runtime_put() to fix it"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: use atomic runtime pm api in clk_core_is_enabled
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED fix from Jacek Anaszewski:
"A single LED fix for brightness setting when delay_off is 0"
* tag 'led_fixes_for_4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
led: core: Fix brightness setting when setting delay_off=0
|
|
Pull rdma fixes from Jason Gunthorpe:
"This is the next batch of for-rc patches from RDMA. It includes the
fix for the ipoib regression I mentioned last time, and the result of
a fairly major debugging effort to get iser working reliably on cxgb4
hardware - it turns out the cxgb4 driver was not handling QP error
flushing properly causing iser to fail.
- cxgb4 fix for an iser testing failure as debugged by Steve and
Sagi. The problem was a driver bug in the handling of shutting down
a QP.
- Various vmw_pvrdma fixes for bogus WARN_ON, missed resource free on
error unwind and a use after free bug
- Improper congestion counter values on mlx5 when link aggregation is
enabled
- ipoib lockdep regression introduced in this merge window
- hfi1 regression supporting the device in a VM introduced in a
recent patch
- Typo that breaks future uAPI compatibility in the verbs core
- More SELinux related oops fixing
- Fix an oops during error unwind in mlx5"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
IB/mlx5: Fix mlx5_ib_alloc_mr error flow
IB/core: Verify that QP is security enabled in create and destroy
IB/uverbs: Fix command checking as part of ib_uverbs_ex_modify_qp()
IB/mlx5: Serialize access to the VMA list
IB/hfi: Only read capability registers if the capability exists
IB/ipoib: Fix lockdep issue found on ipoib_ib_dev_heavy_flush
IB/mlx5: Fix congestion counters in LAG mode
RDMA/vmw_pvrdma: Avoid use after free due to QP/CQ/SRQ destroy
RDMA/vmw_pvrdma: Use refcount_dec_and_test to avoid warning
RDMA/vmw_pvrdma: Call ib_umem_release on destroy QP path
iw_cxgb4: when flushing, complete all wrs in a chain
iw_cxgb4: reflect the original WR opcode in drain cqes
iw_cxgb4: Only validate the MSN for successful completions
|
|
Tom Herbert says:
====================
strparser: Fix lockdep issue
When sock_owned_by_user returns true in strparser. Fix is to add and
call sock_owned_by_user_nocheck since the check for owned by user is
not an error condition in this case.
====================
Fixes: 43a0c6751a322847 ("strparser: Stream parser for messages")
Reported-by: syzbot <[email protected]>
Reported-and-tested-by: <syzbot+c91c53af67f9ebe599a337d2e70950366153b295@syzkaller.appspotmail.com>
Signed-off-by: David S. Miller <[email protected]>
|
|
strparser wants to check socket ownership without producing any
warnings. As indicated by the comment in the code, it is permissible
for owned_by_user to return true.
Fixes: 43a0c6751a322847 ("strparser: Stream parser for messages")
Reported-by: syzbot <[email protected]>
Reported-and-tested-by: <syzbot+c91c53af67f9ebe599a337d2e70950366153b295@syzkaller.appspotmail.com>
Signed-off-by: Tom Herbert <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This allows checking socket lock ownership with producing lockdep
warnings.
Signed-off-by: Tom Herbert <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
skb_copy_ubufs must unclone before it is safe to modify its
skb_shared_info with skb_zcopy_clear.
Commit b90ddd568792 ("skbuff: skb_copy_ubufs must release uarg even
without user frags") ensures that all skbs release their zerocopy
state, even those without frags.
But I forgot an edge case where such an skb arrives that is cloned.
The stack does not build such packets. Vhost/tun skbs have their
frags orphaned before cloning. TCP skbs only attach zerocopy state
when a frag is added.
But if TCP packets can be trimmed or linearized, this might occur.
Tracing the code I found no instance so far (e.g., skb_linearize
ends up calling skb_zcopy_clear if !skb->data_len).
Still, it is non-obvious that no path exists. And it is fragile to
rely on this.
Fixes: b90ddd568792 ("skbuff: skb_copy_ubufs must release uarg even without user frags")
Signed-off-by: Willem de Bruijn <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In commit 42b531de17d2f6 ("tipc: Fix missing connection request
handling"), we replaced unconditional wakeup() with condtional
wakeup for clients with flags POLLIN | POLLRDNORM | POLLRDBAND.
This breaks the applications which do a connect followed by poll
with POLLOUT flag. These applications are not woken when the
connection is ESTABLISHED and hence sleep forever.
In this commit, we fix it by including the POLLOUT event for
sockets in TIPC_CONNECTING state.
Fixes: 42b531de17d2f6 ("tipc: Fix missing connection request handling")
Acked-by: Jon Maloy <[email protected]>
Signed-off-by: Parthasarathy Bhuvaragan <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Fix the following Clang enum conversion warning:
arch/x86/decode.c:141:20: error: implicit conversion from enumeration
type 'enum op_src_type' to different enumeration
type 'enum op_dest_type' [-Werror,-Wenum-conversion]
op->dest.type = OP_SRC_REG;
~ ^~~~~~~~~~
It just happened to work before because OP_SRC_REG and OP_DEST_REG have
the same value.
Signed-off-by: Lukas Bulwahn <[email protected]>
Signed-off-by: Josh Poimboeuf <[email protected]>
Reviewed-by: Nicholas Mc Guire <[email protected]>
Reviewed-by: Nick Desaulniers <[email protected]>
Cc: Jiri Slaby <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Fixes: baa41469a7b9 ("objtool: Implement stack validation 2.0")
Link: http://lkml.kernel.org/r/b4156c5738bae781c392e7a3691aed4514ebbdf2.1514323568.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <[email protected]>
|
|
There are two consumers of apic=: the APIC debug level and the low
level generic architecture code, but Linux just documented the first
one.
Append the second description.
Signed-off-by: Dou Liyang <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Link: https://lkml.kernel.org/r/[email protected]
|
|
There are two consumers of apic=:
apic_set_verbosity() for setting the APIC debug level;
parse_apic() for registering APIC driver by hand.
X86-32 supports both of them, but sometimes, kernel issues a weird warning.
eg: when kernel was booted up with 'apic=bigsmp' in command line,
early_param would warn like that:
...
[ 0.000000] APIC Verbosity level bigsmp not recognised use apic=verbose or apic=debug
[ 0.000000] Malformed early option 'apic'
...
Wrap the warning code in CONFIG_X86_64 case to avoid this.
Signed-off-by: Dou Liyang <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Link: https://lkml.kernel.org/r/[email protected]
|
|
An interrupt storm on a bad interrupt will cause the kernel
log to be clogged.
[ 60.089234] ->handle_irq(): ffffffffbe2f803f,
[ 60.090455] 0xffffffffbf2af380
[ 60.090510] handle_bad_irq+0x0/0x2e5
[ 60.090522] ->irq_data.chip(): ffffffffbf2af380,
[ 60.090553] IRQ_NOPROBE set
[ 60.090584] ->handle_irq(): ffffffffbe2f803f,
[ 60.090590] handle_bad_irq+0x0/0x2e5
[ 60.090596] ->irq_data.chip(): ffffffffbf2af380,
[ 60.090602] 0xffffffffbf2af380
[ 60.090608] ->action(): (null)
[ 60.090779] handle_bad_irq+0x0/0x2e5
This was seen when running an upstream kernel on Acer Chromebook R11. The
system was unstable as result.
Guard the log message with __printk_ratelimit to reduce the impact. This
won't prevent the interrupt storm from happening, but at least the system
remains stable.
Signed-off-by: Guenter Roeck <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Cc: Dmitry Torokhov <[email protected]>
Cc: Joe Perches <[email protected]>
Cc: Andy Shevchenko <[email protected]>
Cc: Mika Westerberg <[email protected]>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=197953
Link: https://lkml.kernel.org/r/[email protected]
|
|
Since the recent remote cpufreq callback work, its possible that a cpufreq
update is triggered from a remote CPU. For single policies however, the current
code uses the local CPU when trying to determine if the remote sg_cpu entered
idle or is busy. This is incorrect. To remedy this, compare with the nohz tick
idle_calls counter of the remote CPU.
Fixes: 674e75411fc2 (sched: cpufreq: Allow remote cpufreq callbacks)
Acked-by: Viresh Kumar <[email protected]>
Acked-by: Peter Zijlstra (Intel) <[email protected]>
Signed-off-by: Joel Fernandes <[email protected]>
Cc: 4.14+ <[email protected]> # 4.14+
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
The IRQ code already has support for lockdep class for the lock mutex
in an interrupt descriptor. Extend this to add a second class for the
request mutex in the descriptor. Not having a class is resulting in
false positive splats in some code paths.
Signed-off-by: Andrew Lunn <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Acked-by: [email protected]
Cc: [email protected]
Cc: [email protected]
Link: https://lkml.kernel.org/r/[email protected]
|
|
Daniel Borkmann says:
====================
pull-request: bpf 2017-12-28
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Two small fixes for bpftool. Fix otherwise broken output if any of
the system calls failed when listing maps in json format and instead
of bailing out, skip maps or progs that disappeared between fetching
next id and getting an fd for that id, both from Jakub.
2) Small fix in BPF selftests to respect LLC passed from command line
when testing for -mcpu=probe presence, from Quentin.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
Commit v4.12-rc4-1-g9289ea7f952b introduced a mistake that made the
64-bit hweight stub call the 16-bit hweight function.
Fixes: 9289ea7f952b ("sparc64: Use indirect calls in hamming weight stubs")
Signed-off-by: Jan Engelhardt <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
ibmr.device is being set only after ib_alloc_mr() is
(successfully) complete. Therefore, in case mlx5_core_create_mkey()
return with error, the error flow calls mlx5_free_priv_descs()
which uses ibmr.device (which doesn't exist yet), causing
a NULL dereference oops.
To fix this, the IB device should be set in the mr struct earlier
stage (e.g. prior to calling mlx5_core_create_mkey()).
Fixes: 8a187ee52b04 ("IB/mlx5: Support the new memory registration API")
Signed-off-by: Max Gurtovoy <[email protected]>
Signed-off-by: Nitzan Carmi <[email protected]>
Signed-off-by: Leon Romanovsky <[email protected]>
Signed-off-by: Jason Gunthorpe <[email protected]>
|
|
The XRC target QP create flow sets up qp_sec only if there is an IB link with
LSM security enabled. However, several other related uAPI entry points blindly
follow the qp_sec NULL pointer, resulting in a possible oops.
Check for NULL before using qp_sec.
Cc: <[email protected]> # v4.12
Fixes: d291f1a65232 ("IB/core: Enforce PKey security on QPs")
Reviewed-by: Daniel Jurgens <[email protected]>
Signed-off-by: Moni Shoua <[email protected]>
Signed-off-by: Leon Romanovsky <[email protected]>
Signed-off-by: Jason Gunthorpe <[email protected]>
|
|
If the input command length is larger than the kernel supports an error should
be returned in case the unsupported bytes are not cleared, instead of the
other way aroudn. This matches what all other callers of ib_is_udata_cleared
do and will avoid user ABI problems in the future.
Cc: <[email protected]> # v4.10
Fixes: 189aba99e700 ("IB/uverbs: Extend modify_qp and support packet pacing")
Reviewed-by: Yishai Hadas <[email protected]>
Signed-off-by: Moni Shoua <[email protected]>
Signed-off-by: Leon Romanovsky <[email protected]>
Signed-off-by: Jason Gunthorpe <[email protected]>
|
|
User-space applications can do mmap and munmap directly at
any time.
Since the VMA list is not protected with a mutex, concurrent
accesses to the VMA list from the mmap and munmap can cause
data corruption. Add a mutex around the list.
Cc: <[email protected]> # v4.7
Fixes: 7c2344c3bbf9 ("IB/mlx5: Implements disassociate_ucontext API")
Reviewed-by: Yishai Hadas <[email protected]>
Signed-off-by: Majd Dibbiny <[email protected]>
Signed-off-by: Leon Romanovsky <[email protected]>
Signed-off-by: Jason Gunthorpe <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"While doing tests on tracing over the network, I found that the
packets were getting corrupted.
In the process I found three bugs.
One was the culprit, but the other two scared me. After deeper
investigation, they were not as major as I thought they were, due to a
signed compared to an unsigned that prevented a negative number from
doing actual harm.
The two bigger bugs:
- Mask the ring buffer data page length. There are data flags at the
high bits of the length field. These were not cleared via the
length function, and the length could return a negative number.
(Although the number returned was unsigned, but was assigned to a
signed number) Luckily, this value was compared to PAGE_SIZE which
is unsigned and kept it from entering the path that could have
caused damage.
- Check the page usage before reusing the ring buffer reader page.
TCP increments the page ref when passing the page off to the
network. The page is passed back to the ring buffer for use on
free. But the page could still be in use by the TCP stack.
Minor bugs:
- Related to the first bug. No need to clear out the unused ring
buffer data before sending to user space. It is now done by the
ring buffer code itself.
- Reset pointers after free on error path. There were some cases in
the error path that pointers were freed but not set to NULL, and
could have them freed again, having a pointer freed twice"
* tag 'trace-v4.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Fix possible double free on failure of allocating trace buffer
tracing: Fix crash when it fails to alloc ring buffer
ring-buffer: Do no reuse reader page if still in use
tracing: Remove extra zeroing out of the ring buffer page
ring-buffer: Mask out the info bits when returning buffer page length
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"It seems that Santa overslept with a bunch of gifts; the majority of
changes here are various device-specific ASoC fixes, most notably the
revert of rcar IOMMU support and fsl_ssi AC97 fixes, but also lots of
small fixes for codecs. Besides that, the usual HD-audio quirks and
fixes are included, too"
* tag 'sound-4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (31 commits)
ALSA: hda - Fix missing COEF init for ALC225/295/299
ALSA: hda: Drop useless WARN_ON()
ALSA: hda - change the location for one mic on a Lenovo machine
ALSA: hda - fix headset mic detection issue on a Dell machine
ALSA: hda - Add MIC_NO_PRESENCE fixup for 2 HP machines
ASoC: rsnd: fixup ADG register mask
ASoC: rt5514-spi: only enable wakeup when fully initialized
ASoC: nau8825: fix issue that pop noise when start capture
ASoC: rt5663: Fix the wrong result of the first jack detection
ASoC: rsnd: ssi: fix race condition in rsnd_ssi_pointer_update
ASoC: Intel: Change kern log level to avoid unwanted messages
ASoC: atmel-classd: select correct Kconfig symbol
ASoC: wm_adsp: Fix validation of firmware and coeff lengths
ASoC: Intel: Skylake: Do not check dev_type for dmic link type
ASoC: rockchip: disable clock on error
ASoC: tlv320aic31xx: Fix GPIO1 register definition
ASoC: codecs: msm8916-wcd: Fix supported formats
ASoC: fsl_asrc: Fix typo in a field define
ASoC: rsnd: ssiu: clear SSI_MODE for non TDM Extended modes
ASoC: da7218: Correct IRQ level in DT binding example
...
|
|
Commit e802a51ede91 ("x86/idt: Consolidate IDT invalidation") cleaned up
and unified the IDT invalidation that existed in a couple of places. It
changed no actual real code.
Despite not changing any actual real code, it _did_ change code generation:
by implementing the common idt_invalidate() function in
archx86/kernel/idt.c, it made the use of the function in
arch/x86/kernel/machine_kexec_32.c be a real function call rather than an
(accidental) inlining of the function.
That, in turn, exposed two issues:
- in load_segments(), we had incorrectly reset all the segment
registers, which then made the stack canary load (which gcc does
using offset of %gs) cause a trap. Instead of %gs pointing to the
stack canary, it will be the normal zero-based kernel segment, and
the stack canary load will take a page fault at address 0x14.
- to make this even harder to debug, we had invalidated the GDT just
before calling idt_invalidate(), which meant that the fault happened
with an invalid GDT, which in turn causes a triple fault and
immediate reboot.
Fix this by
(a) not reloading the special segments in load_segments(). We currently
don't do any percpu accesses (which would require %fs on x86-32) in
this area, but there's no reason to think that we might not want to
do them, and like %gs, it's pointless to break it.
(b) doing idt_invalidate() before invalidating the GDT, to keep things
at least _slightly_ more debuggable for a bit longer. Without a
IDT, traps will not work. Without a GDT, traps also will not work,
but neither will any segment loads etc. So in a very real sense,
the GDT is even more core than the IDT.
Fixes: e802a51ede91 ("x86/idt: Consolidate IDT invalidation")
Reported-and-tested-by: Alexandru Chirvasitu <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Cc: Denys Vlasenko <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Brian Gerst <[email protected]>
Cc: Steven Rostedt <[email protected]>
Cc: Borislav Petkov <[email protected]>
Cc: Andy Lutomirski <[email protected]>
Cc: Josh Poimboeuf <[email protected]>
Cc: [email protected]
Link: https://lkml.kernel.org/r/[email protected]
|
|
With the current code, the following sequence won't work :
echo timer > trigger
echo 0 > delay_off
* at this point we call
** led_delay_off_store
** led_blink_set
*** stop timer
** led_blink_setup
** led_set_software_blink
*** if !delay_on, led off
*** if !delay_off, set led_set_brightness_nosleep <--- LED_BLINK_SW is set but timer is stop
*** otherwise start timer/set LED_BLINK_SW flag
echo xxx > brightness
* led_set_brightness
** if LED_BLINK_SW
*** if brightness=0, led off
*** else apply brightness if next timer <--- timer is stop, and will never apply new setting
** otherwise set led_set_brightness_nosleep
To fix that, when we delete the timer, we should clear LED_BLINK_SW.
Cc: [email protected]
Signed-off-by: Matthieu CASTET <[email protected]>
Signed-off-by: Jacek Anaszewski <[email protected]>
|
|
Commit e37e43a497d5 ("x86/mm/64: Enable vmapped stacks
(CONFIG_HAVE_ARCH_VMAP_STACK=y)") added prepare_switch_to with one extra
parameter which is not used by the function, remove it.
Signed-off-by: Rodrigo Siqueira <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Cc: [email protected]
Link: https://lkml.kernel.org/r/[email protected]
|
|
A recent commit introduced an extra merge_attr() call in the skylake
branch, which causes a memory leak.
Store the pointer to the extra allocated memory and free it at the end of
the function.
Fixes: a5df70c354c2 ("perf/x86: Only show format attributes when supported")
Reported-by: Tommi Rantala <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Cc: Andi Kleen <[email protected]>
|
|
Jing Xia and Chunyan Zhang reported that on failing to allocate part of the
tracing buffer, memory is freed, but the pointers that point to them are not
initialized back to NULL, and later paths may try to free the freed memory
again. Jing and Chunyan fixed one of the locations that does this, but
missed a spot.
Link: http://lkml.kernel.org/r/[email protected]
Cc: [email protected]
Fixes: 737223fbca3b1 ("tracing: Consolidate buffer allocation code")
Reported-by: Jing Xia <[email protected]>
Reported-by: Chunyan Zhang <[email protected]>
Signed-off-by: Steven Rostedt (VMware) <[email protected]>
|
|
Double free of the ring buffer happens when it fails to alloc new
ring buffer instance for max_buffer if TRACER_MAX_TRACE is configured.
The root cause is that the pointer is not set to NULL after the buffer
is freed in allocate_trace_buffers(), and the freeing of the ring
buffer is invoked again later if the pointer is not equal to Null,
as:
instance_mkdir()
|-allocate_trace_buffers()
|-allocate_trace_buffer(tr, &tr->trace_buffer...)
|-allocate_trace_buffer(tr, &tr->max_buffer...)
// allocate fail(-ENOMEM),first free
// and the buffer pointer is not set to null
|-ring_buffer_free(tr->trace_buffer.buffer)
// out_free_tr
|-free_trace_buffers()
|-free_trace_buffer(&tr->trace_buffer);
//if trace_buffer is not null, free again
|-ring_buffer_free(buf->buffer)
|-rb_free_cpu_buffer(buffer->buffers[cpu])
// ring_buffer_per_cpu is null, and
// crash in ring_buffer_per_cpu->pages
Link: http://lkml.kernel.org/r/[email protected]
Cc: [email protected]
Fixes: 737223fbca3b1 ("tracing: Consolidate buffer allocation code")
Signed-off-by: Jing Xia <[email protected]>
Signed-off-by: Chunyan Zhang <[email protected]>
Signed-off-by: Steven Rostedt (VMware) <[email protected]>
|
|
To free the reader page that is allocated with ring_buffer_alloc_read_page(),
ring_buffer_free_read_page() must be called. For faster performance, this
page can be reused by the ring buffer to avoid having to free and allocate
new pages.
The issue arises when the page is used with a splice pipe into the
networking code. The networking code may up the page counter for the page,
and keep it active while sending it is queued to go to the network. The
incrementing of the page ref does not prevent it from being reused in the
ring buffer, and this can cause the page that is being sent out to the
network to be modified before it is sent by reading new data.
Add a check to the page ref counter, and only reuse the page if it is not
being used anywhere else.
Cc: [email protected]
Fixes: 73a757e63114d ("ring-buffer: Return reader page back into existing ring buffer")
Signed-off-by: Steven Rostedt (VMware) <[email protected]>
|
|
The ring_buffer_read_page() takes care of zeroing out any extra data in the
page that it returns. There's no need to zero it out again from the
consumer. It was removed from one consumer of this function, but
read_buffers_splice_read() did not remove it, and worse, it contained a
nasty bug because of it.
Cc: [email protected]
Fixes: 2711ca237a084 ("ring-buffer: Move zeroing out excess in page to ring buffer code")
Signed-off-by: Steven Rostedt (VMware) <[email protected]>
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
GLK pipe C related fix, and a gvt fix.
* tag 'drm-intel-fixes-2017-12-22-1' of git://anongit.freedesktop.org/drm/drm-intel:
i915: Reject CCS modifiers for pipe C on Geminilake
drm/i915/gvt: Fix pipe A enable as default for vgpu
|
|
Two info bits were added to the "commit" part of the ring buffer data page
when returned to be consumed. This was to inform the user space readers that
events have been missed, and that the count may be stored at the end of the
page.
What wasn't handled, was the splice code that actually called a function to
return the length of the data in order to zero out the rest of the page
before sending it up to user space. These data bits were returned with the
length making the value negative, and that negative value was not checked.
It was compared to PAGE_SIZE, and only used if the size was less than
PAGE_SIZE. Luckily PAGE_SIZE is unsigned long which made the compare an
unsigned compare, meaning the negative size value did not end up causing a
large portion of memory to be randomly zeroed out.
Cc: [email protected]
Fixes: 66a8cb95ed040 ("ring-buffer: Add place holder recording of dropped events")
Signed-off-by: Steven Rostedt (VMware) <[email protected]>
|
|
The patch(180d8cd942ce) replaces all uses of struct sock fields'
memory_pressure, memory_allocated, sockets_allocated, and sysctl_mem
to accessor macros. But the sockets_allocated field of sctp sock is
not replaced at all. Then replace it now for unifying the code.
Fixes: 180d8cd942ce ("foundations of per-cgroup memory pressure controlling.")
Cc: Glauber Costa <[email protected]>
Signed-off-by: Tonghao Zhang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Fix non-fatal warnings such as:
kernel/cpu.c:95:1: warning: ‘inline’ is not at beginning of declaration [-Wold-style-declaration]
static void inline cpuhp_lock_release(bool bringup) { }
^~~~~~
Signed-off-by: Mathieu Malaterre <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Cc: Arnd Bergmann <[email protected]>
Cc: Sebastian Andrzej Siewior <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: "Paul E. McKenney" <[email protected]>
Link: https://lkml.kernel.org/r/[email protected]
|
|
While in recovery process of PCI error (called EEH on PowerPC arch),
another PCI transaction could be corrupted causing a situation of
nested PCI errors. Also, this scenario could be reproduced with
error injection mechanisms (for debug purposes).
We observe that in case of nested PCI errors, bnx2x might attempt to
initialize its shmem and cause a kernel crash due to bad addresses
read from MCP. Multiple different stack traces were observed depending
on the point the second PCI error happens.
This patch avoids the crashes by:
* failing PCI recovery in case of nested errors (since multiple
PCI errors in a row are not expected to lead to a functional
adapter anyway), and by,
* preventing access to adapter FW when MCP is failed (we mark it as
failed when shmem cannot get initialized properly).
Reported-by: Abdul Haleem <[email protected]>
Signed-off-by: Guilherme G. Piccoli <[email protected]>
Acked-by: Shahed Shaikh <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Siva Reddy Kallam says:
====================
tg3: update on copyright and couple of fixes
First patch:
Update copyright
Second patch:
Add workaround to restrict 5762 MRRS
Third patch:
Add PHY reset in change MTU path for 5720
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
A customer noticed RX path hang when MTU is changed on the fly while
running heavy traffic with NCSI enabled for 5717 and 5719. Since 5720
belongs to same ASIC family, we observed same issue and same fix
could solve this problem for 5720.
Signed-off-by: Siva Reddy Kallam <[email protected]>
Signed-off-by: Michael Chan <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
One of AMD based server with 5762 hangs with jumbo frame traffic.
This AMD platform has southbridge limitation which is restricting MRRS
to 4000. As a work around, driver to restricts the MRRS to 2048 for
this particular 5762 NX1 card.
Signed-off-by: Siva Reddy Kallam <[email protected]>
Signed-off-by: Michael Chan <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Signed-off-by: Siva Reddy Kallam <[email protected]>
Signed-off-by: Michael Chan <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec
Steffen Klassert says:
====================
pull request (net): ipsec 2017-12-22
1) Check for valid id proto in validate_tmpl(), otherwise
we may trigger a warning in xfrm_state_fini().
From Cong Wang.
2) Fix a typo on XFRMA_OUTPUT_MARK policy attribute.
From Michal Kubecek.
3) Verify the state is valid when encap_type < 0,
otherwise we may crash on IPsec GRO .
From Aviv Heller.
4) Fix stack-out-of-bounds read on socket policy lookup.
We access the flowi of the wrong address family in the
IPv4 mapped IPv6 case, fix this by catching address
family missmatches before we do the lookup.
5) fix xfrm_do_migrate() with AEAD to copy the geniv
field too. Otherwise the state is not fully initialized
and migration fails. From Antony Antony.
6) Fix stack-out-of-bounds with misconfigured transport
mode policies. Our policy template validation is not
strict enough. It is possible to configure policies
with transport mode template where the address family
of the template does not match the selectors address
family. Fix this by refusing such a configuration,
address family can not change on transport mode.
7) Fix a policy reference leak when reusing pcpu xdst
entry. From Florian Westphal.
8) Reinject transport-mode packets through tasklet,
otherwise it is possible to reate a recursion
loop. From Herbert Xu.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
The enet IP only support 32 bit, it will use swiotlb buffer to do dma
mapping when xmit buffer DMA memory address is bigger than 4G in i.MX
platform. After stress suspend/resume test, it will print out:
log:
[12826.352864] fec 5b040000.ethernet: swiotlb buffer is full (sz: 191 bytes)
[12826.359676] DMA: Out of SW-IOMMU space for 191 bytes at device 5b040000.ethernet
[12826.367110] fec 5b040000.ethernet eth0: Tx DMA memory map failed
The issue is that the ready xmit buffers that are dma mapped but DMA still
don't copy them into fifo, once MAC restart, these DMA buffers are not unmapped.
So it should check the dma mapping buffer and unmap them.
Signed-off-by: Fugang Duan <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Calling tipc_mon_delete() before the monitor has been created will oops.
This can happen in tipc_enable_bearer() error path if tipc_disc_create()
fails.
[ 48.589074] BUG: unable to handle kernel paging request at 0000000000001008
[ 48.590266] IP: tipc_mon_delete+0xea/0x270 [tipc]
[ 48.591223] PGD 1e60c5067 P4D 1e60c5067 PUD 1eb0cf067 PMD 0
[ 48.592230] Oops: 0000 [#1] SMP KASAN
[ 48.595610] CPU: 5 PID: 1199 Comm: tipc Tainted: G B 4.15.0-rc4-pc64-dirty #5
[ 48.597176] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-2.fc27 04/01/2014
[ 48.598489] RIP: 0010:tipc_mon_delete+0xea/0x270 [tipc]
[ 48.599347] RSP: 0018:ffff8801d827f668 EFLAGS: 00010282
[ 48.600705] RAX: ffff8801ee813f00 RBX: 0000000000000204 RCX: 0000000000000000
[ 48.602183] RDX: 1ffffffff1de6a75 RSI: 0000000000000297 RDI: 0000000000000297
[ 48.604373] RBP: 0000000000000000 R08: 0000000000000000 R09: fffffbfff1dd1533
[ 48.605607] R10: ffffffff8eafbb05 R11: fffffbfff1dd1534 R12: 0000000000000050
[ 48.607082] R13: dead000000000200 R14: ffffffff8e73f310 R15: 0000000000001020
[ 48.608228] FS: 00007fc686484800(0000) GS:ffff8801f5540000(0000) knlGS:0000000000000000
[ 48.610189] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 48.611459] CR2: 0000000000001008 CR3: 00000001dda70002 CR4: 00000000003606e0
[ 48.612759] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 48.613831] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 48.615038] Call Trace:
[ 48.615635] tipc_enable_bearer+0x415/0x5e0 [tipc]
[ 48.620623] tipc_nl_bearer_enable+0x1ab/0x200 [tipc]
[ 48.625118] genl_family_rcv_msg+0x36b/0x570
[ 48.631233] genl_rcv_msg+0x5a/0xa0
[ 48.631867] netlink_rcv_skb+0x1cc/0x220
[ 48.636373] genl_rcv+0x24/0x40
[ 48.637306] netlink_unicast+0x29c/0x350
[ 48.639664] netlink_sendmsg+0x439/0x590
[ 48.642014] SYSC_sendto+0x199/0x250
[ 48.649912] do_syscall_64+0xfd/0x2c0
[ 48.650651] entry_SYSCALL64_slow_path+0x25/0x25
[ 48.651843] RIP: 0033:0x7fc6859848e3
[ 48.652539] RSP: 002b:00007ffd25dff938 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
[ 48.654003] RAX: ffffffffffffffda RBX: 00007ffd25dff990 RCX: 00007fc6859848e3
[ 48.655303] RDX: 0000000000000054 RSI: 00007ffd25dff990 RDI: 0000000000000003
[ 48.656512] RBP: 00007ffd25dff980 R08: 00007fc685c35fc0 R09: 000000000000000c
[ 48.657697] R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000d13010
[ 48.658840] R13: 00007ffd25e009c0 R14: 0000000000000000 R15: 0000000000000000
[ 48.662972] RIP: tipc_mon_delete+0xea/0x270 [tipc] RSP: ffff8801d827f668
[ 48.664073] CR2: 0000000000001008
[ 48.664576] ---[ end trace e811818d54d5ce88 ]---
Acked-by: Ying Xue <[email protected]>
Acked-by: Jon Maloy <[email protected]>
Signed-off-by: Tommi Rantala <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Fix memory leak in tipc_enable_bearer() if enable_media() fails, and
cleanup with bearer_disable() if tipc_mon_create() fails.
Acked-by: Ying Xue <[email protected]>
Acked-by: Jon Maloy <[email protected]>
Signed-off-by: Tommi Rantala <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
RDS currently doesn't check if the length of the control message is
large enough to hold the required data, before dereferencing the control
message data. This results in following crash:
BUG: KASAN: stack-out-of-bounds in rds_rdma_bytes net/rds/send.c:1013
[inline]
BUG: KASAN: stack-out-of-bounds in rds_sendmsg+0x1f02/0x1f90
net/rds/send.c:1066
Read of size 8 at addr ffff8801c928fb70 by task syzkaller455006/3157
CPU: 0 PID: 3157 Comm: syzkaller455006 Not tainted 4.15.0-rc3+ #161
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:17 [inline]
dump_stack+0x194/0x257 lib/dump_stack.c:53
print_address_description+0x73/0x250 mm/kasan/report.c:252
kasan_report_error mm/kasan/report.c:351 [inline]
kasan_report+0x25b/0x340 mm/kasan/report.c:409
__asan_report_load8_noabort+0x14/0x20 mm/kasan/report.c:430
rds_rdma_bytes net/rds/send.c:1013 [inline]
rds_sendmsg+0x1f02/0x1f90 net/rds/send.c:1066
sock_sendmsg_nosec net/socket.c:628 [inline]
sock_sendmsg+0xca/0x110 net/socket.c:638
___sys_sendmsg+0x320/0x8b0 net/socket.c:2018
__sys_sendmmsg+0x1ee/0x620 net/socket.c:2108
SYSC_sendmmsg net/socket.c:2139 [inline]
SyS_sendmmsg+0x35/0x60 net/socket.c:2134
entry_SYSCALL_64_fastpath+0x1f/0x96
RIP: 0033:0x43fe49
RSP: 002b:00007fffbe244ad8 EFLAGS: 00000217 ORIG_RAX: 0000000000000133
RAX: ffffffffffffffda RBX: 00000000004002c8 RCX: 000000000043fe49
RDX: 0000000000000001 RSI: 000000002020c000 RDI: 0000000000000003
RBP: 00000000006ca018 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000217 R12: 00000000004017b0
R13: 0000000000401840 R14: 0000000000000000 R15: 0000000000000000
To fix this, we verify that the cmsg_len is large enough to hold the
data to be read, before proceeding further.
Reported-by: syzbot <[email protected]>
Signed-off-by: Avinash Repaka <[email protected]>
Acked-by: Santosh Shilimkar <[email protected]>
Reviewed-by: Yuval Shaia <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
When plugging in a USB webcam I see the following message:
xhci_hcd 0000:04:00.0: WARN Successful completion on short TX: needs
XHCI_TRUST_TX_LENGTH quirk?
handle_tx_event: 913 callbacks suppressed
All is quiet again with this patch (and I've done a fair but of soak
testing with the camera since).
Cc: <[email protected]>
Signed-off-by: Daniel Thompson <[email protected]>
Acked-by: Ard Biesheuvel <[email protected]>
Signed-off-by: Mathias Nyman <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Trying to read from debugfs after the system has resumed from
hibernate causes a use-after-free and thus a protection fault.
Steps to reproduce:
Hibernate system, resume from hibernate, then run
$ cat /sys/kernel/debug/usb/xhci/*/command-ring/enqueue
[ 3902.765086] general protection fault: 0000 [#1] PREEMPT SMP
...
[ 3902.765136] RIP: 0010:xhci_trb_virt_to_dma.part.50+0x5/0x30
...
[ 3902.765178] Call Trace:
[ 3902.765188] xhci_ring_enqueue_show+0x1e/0x40
[ 3902.765197] seq_read+0xdb/0x3a0
[ 3902.765204] ? __handle_mm_fault+0x5fb/0x1210
[ 3902.765211] full_proxy_read+0x4a/0x70
[ 3902.765219] __vfs_read+0x23/0x120
[ 3902.765228] vfs_read+0x8e/0x130
[ 3902.765235] SyS_read+0x42/0x90
[ 3902.765242] do_syscall_64+0x6b/0x290
[ 3902.765251] entry_SYSCALL64_slow_path+0x25/0x25
The issue is caused by the xhci ring structures being reallocated
when the system is resumed, but pointers to the old structures
being retained in the debugfs files "private" field:
The proposed patch fixes this issue by storing a pointer to the xhci_ring
field in the xhci device structure in debugfs rather than directly
storing a pointer to the xhci_ring.
Fixes: 02b6fdc2a153 ("usb: xhci: Add debugfs interface for xHCI driver")
Signed-off-by: Alexander Kappner <[email protected]>
Signed-off-by: Mathias Nyman <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|